SCC-931T(P)
1/4 High Resolution, Anti Vandal Dome Color Digital Camera, Motorized 12x Zoom Lens

Features

High impact, vandal resistant dome (Shock/water/dust proof : IP66 grade) x12 motorized optical zoom with x10 digital zoom DSP (Digital Signal Processor) 1/4 410,000 (PAL 470,000) super HAD CCD Horizontal resolution (480 TV Lines) Back Light Compensation covers various light conditions External synchronization with linelock Motion detection function with alarming output On-screen menus (Multi-language) Picture in Picture on digital zoom Remote control: RS485 (Half duplex) Power input (AC24V/DC12V compatible) Built-in ground fault isolation transformer

SCC-641(P)/SCC-643A(P)

SmartDome Camera

Dimensions (unit : mm)

Rear Panel

Specifications

SCC-931TP
Camera Type Image Color Device Size Pixels - Total Pixels - Effective System Horizontal Frequency-Internal Mode Horizontal Frequency-Line-lock Mode Vertical Frequency-Internal Mode Vertical Frequency-Line-lock Mode Color Range-Panning Range-Tilting Motion Detection D-Zoom High Speed Shutter Sense Up PIP BLC AGC Line Lock Anti Vandal Camera ID White Balance Horizontal Vertical VBS 1.0Vp-p S/N Ratio Focal Length Zoom Ratio Aperture Ratio Viewing Angle-Tele Viewing Angle-Wide Lens Drive Type OSD Output RS485 Operating Temperature Humidity Power Requirement Power Consumption LED Indicator Dimensions (WxHxD)-Net Weight-Net Loading Quantity(20/40ft) Package Size Color CCD 1/4 inch 795 x x 582 Interlace 15,625 Hz 15,625 Hz 50 Hz 50 Hz 1 Lux(Sense Up x128 : 0.01) 360 (Manual) 90 (Manual) Off/On Off ~ x10 Off ~ 1/10Ksec Off ~ x128 Off/On Off/On Off/On Off/On Yes Off/On ATW/AWC/MANUAL 480 TV Lines 350 TV Lines VBS 1.0Vp-p 52dB 3.6 ~ 43.2 mm x12 F1.8(Wide), F2.6(Tele) 4 7(H) x 3 6(V) 52 8(H) x (V) AI (DC) Yes 1 Yes -10 C ~ +50 C Less than 90% AC24V(60Hz)10%, DC12V+10%/-5% 6W Yes 132() x 96.5(H) mm 1000g 4,080/8,x 335 x 160 mm

SCC-931T

Color CCD 1/4 inch 811 x x 494 Interlace 15,734 Hz 15,750 Hz 59.94 Hz 60 Hz 1 Lux(Sense Up x128 : 0.01) 360 (Manual) 90 (Manual) Off/On Off ~ x10 Off ~ 1/10Ksec Off ~ x128 Off/On Off/On Off/On Off/On Yes Off/On ATW/AWC/MANUAL 480 TV Lines 350 TV Lines VBS 1.0Vp-p 52dB 3.6 ~ 43.2 mm x12 F1.8(Wide), F2.6(Tele) 4 7(H) x 3 6(V) 52 8(H) x (V) AI (DC) Yes 1 Yes -10 C ~ +50 C Less than 90% AC24V(60Hz)10%, DC12V+10%/-5% 6W Yes 132() x 96.5(H) mm 1000g 4,080/8,x 335 x 160 mm * Design and specifications are subject to change without notice.

Scanning

Min. scene Illumination PAN/TILT Functions

Summary

This product employs a 10x digital zoom and 22x built-in optical lens to offer up to 220x zoom and can correctly catch an object at a long distance range via the Auto Focus function. Its Digital Signal Processor (DSP) system represents clear and high quality images of objects under either bright or dark settings. It can observe objects clearly under dark circumstances by realizing high sensitivity that allows observation under minimum illumination of 0.01Lux (Sense Up x128). SCC-643A(P) have the Day/Night function as well as the Privacy Zone (8 areas) function by which the user can mask a certain area to protect privacy. This camera can be panned 360 and tilted 90 conveniently with its 64 steps of Manual Pan/Tilt operations. With the moving speed of up to 240/sec during the preset mode, user can instantly observe desired points. It provides a remote control interface of RS-485 (Full-Duplex and Half-Duplex)/ RS-422 and can organize up to 128 cameras in a single system with Samsungs exclusive controllers (SSC-1000 and SSC-2000). One of the main features of this product is that it provides various AUTO functions that can be defined by the user. Its Preset function is distinguished from that of cameras of other manufacturers. Not only it can set 128 camera locations, zooms, and focuses of cameras but it can also perform video setups for the corresponding locations. Thus user can preset and save each video control such as iris control, shutter speed and white balance. This feature enables the expansion of applications of the smart dome under an assortment of installation circumstances. The Scan function executes touring of preset locations in order to observe critical places rapidly. The camera also supports the Auto Pan function that pans the camera to observe a place designated by user at a constant speed to designated directions, and the Pattern function that saves and replays the 30 seconds Pan/Tilt/Zoom operation by user (up to 3 operations). It also provides powerful Alarm In/Out and Motion Detection functions. Four inputs and three outputs are available for the Alarm function. Alarm and motion detection functions can be used by connecting to the Preset and Pattern functions defined by the user.

Resolution Video Output S/N Ratio Lens
OSD Alarm Remote Control Environmental Conditions Power Physical Specification
* "P" indicates PAL model & "N" or no specific alphabet after the model name indicates NTSC model.
SAMSUNG ELECTRONICS CO.,LTD.

Digital Video Division

416, Maetan-3Dong, Yeongtong-Gu, Suwon City, Gyeonggi-Do, Korea 443-742 Tel: +82-31-200-5504, 5578 Fax: +82-31-200-5594 http://www.securitysamsung.com
22x (f=3.6~79.2mm) optical lens, and built-in 10x digital zoom lens (Maximum 220x zoom-in, AF function) RS-485 (Half Duplex Full Duplex)/RS-422 remote control. DSP (Digital Signal Processor) IC suitable Day & Night function (SCC-643A(P)). Minimum illumination of 0.01 Lux (SCC-641(P)) Minimum illumination of 0.01 Lux for Color, 0.003 Lux for B/W (SCC-643A(P)) 360 endless horizontal rotation and 0~90 vertical rotation. Rapid search at maximum rotating speed of 240/sec. Motion detection. Alarm in : 4Ch, Alarm out: 3Ch. More than 480 lines of horizontal resolution. Preset function (Up to 128 locations). Auto functions that can be defined by the user (Preset, auto-pan, and scan). Privacy zone function for 8 locations (SCC-643A(P)).

SCC-C6405(P)

94.5 159.5 151

SCC-641(P)

Image Device Size Pixels-Total Pixels-Effective System Horizontal Frequency-Internal Mode Horizontal Frequency-Line-lock Mode Vertical Frequency-Internal Mode Vertical Frequency-Line-lock Mode Color B/W Speed-Manual Pan Speed-Preset Pan Speed-Manual Tilt Speed-Preset Tilt Range-Panning Range-Tilting Number of Scan Number of Auto PAN Number of Preset Number of Pattern Number of Privacy Zone Day/Night Motion Detection Wide Dynamic Range D-Zoom High Speed Shutter Sense Up PIP BLC AGC Line Lock Camera ID White Balance Horizontal Vertical VBS 1.0Vp-p 52 Focal Length Zoom ratio Aperture Ratio Viewing Angle-Tele Viewing Angle-Wide OSD Input Output RS485/RS-422 Operating Temperature Humidity Power Requirement Power Consumption LED Indicator Dimensions -Net Weight-Net Loading Quantity(20/40ft) Package Size CCD 1/4 inch 641: 811 x 508, 641P: 795 x 596 641: 768 x 494, 641P: 752 x 582 Interlace 641: 15,734 Hz, 641P: 15,625 Hz 641: 15,750 Hz, 641P: 15,625Hz 641: 59.94 Hz, 641P: 50Hz 641: 60 Hz, 641P: 50Hz 0.3 Lux (Sense Up X4 30IRE), 0.01 Lux (Sense Up X128) 0.8 /sec ~ 90 /sec 240 /sec 0.8 /sec ~ 45 /sec 150 /sec 360 (endless) 0 /sec ~ 90 /sec Yes Yes(2X ~ 10X) Yes(OFF ~ 1/10K) Yes(X2 ~ X128) Yes Yes Yes Yes Max 12 Character ATW/AWC/MANUAL 480 TV Lines 350 TV Lines VBS 1.0Vp-p 52 dB 3.6 ~ 79.2 mm 22X F1.6(Wide), F3.8(Tele) 2 3'(H) x 1 7'(V) 47 9'(H) x 36 9'(V) Yes RS485 Half/Full Duplex, RS-422 -10 C ~ +50 C Less than 90% AC24V 10% 18W Yes 159.5()x177(H) 1,700g 756/1,x 308 x 275 mm

SCC-643A(P)

CCD 1/4 inch 643A: 811 x 508, 643AP: 795 x 596 643A: 768 x 494, 643AP: 752 x 582 Interlace 643A: 15,734 Hz, 643AP: 15,625 Hz 643A: 15,750 Hz, 643AP: 15,625 Hz 643A: 59.94 Hz, 643AP: 50Hz 643A: 606 Hz, 643AP: 50 Hz 0.3 Lux (Sense Up X4 30IRE), 0.01 Lux (Sense Up X128) 0.003 Lux 0.8 /sec ~ 90 /sec 240 /sec 0.8 /sec ~ 45 /sec 150 /sec 360(endless) 0 /sec ~ 90 /sec 8 Yes Yes Yes(2X ~ 10X) Yes(OFF ~ 1/10K) Yes(X2 ~ X128) Yes Yes Yes Yes Max 12 Character ATW/AWC/MANUAL VBS 1.0Vp-p 52 dB 3.6 ~ 79.2 mm 22X F1.6(Wide), F3.8(Tele) 2 3'(H) x 1 7'(V) 47 9'(H) x 36 9'(V) Yes RS485 Half/Full Duplex, RS-422 -10 C ~ +50 C Less than 90% AC24V 10% 18W Yes 159.5()x177(H) 1,700g 756/1,x 308 x 275 mm * Design and specifications are subject to change without notice.

Min. Scene Illumination PAN/TILT

Functions

SCC-C6405(P) is a camera equipped with the 1/4" Progressive Ex-View CCD suitable for WDR (Wide Dynamic Range) thus represents clear and perfect images even under backlight conditions where illumination intensity varies excessively. It employs a 10x digital zoom and 22x built-in optical lens to offer up to 220x zoom and precisly catch an object at a long distance range via the Auto Focus function. The Digital Signal Processor (DSP) system represents clear and high quality images of objects under either bright or dark settings. It can observe objects clearly under dark circumstances by realizing high sensitivity that allows observation under minimum illumination [0.007Lux (Sense Up x160)]. SCC-C6405(P) has Day/Night function that switches the camera mode between Day and Night Mode according to the brightness of the object. It also has Mosaic Privacy Zone (12areas) function by which the user can mask a certain area to protect privacy. This camera can be panned 360 and tilted 180 conveniently with its 64 steps of Manual Pan/Tilt operations. With thee moving speed of up to 400/sec during the preset mode, user can instantly observe desired points. It provides a remote control interface of RS-485 (Full-Duplex and Half-Duplex)/ RS-422 and can organize up to 128 cameras in a single system with Samsungs exclusive controllers (SSC-1000 and SSC-2000). SCC-C6405(P) provides various AUTO functions that can be defined by user as one of the main function. Its preset function can not only set 128 camera locations, zooms, and focus of cameras but also perform video setups for the corresponding locations. Thus user can preset and save each video control such as iris control, shutter speed and white balance. SCC-C6405(P) provides Scan/Autopan/Pattern function. It also provides powerful Alarm In/Out and Motion Detection functions. Four inputs and three outputs are available for the Alarm function. Alarm and motion detection functions can be used by being connected to the Preset and Auto functions defined by user.

Combi Dome Camera

SCC-641(P)

Owner s Instructions

Part : AB68-00136A Printed in Korea

Before Usage

This is a basic instruction manual for the SCC-641(P) user. It contains all the instructions needed to use the SCC-641(P) from a simple introduction of the control locations and functions of the SCC-641(P) to installation methods in the set up menu. We recommend all users of the SCC-641(P) from the advanced user who has used similar cameras before to the general user to read the instruction manual before using. The most frequently used feature in the SCC-641(P) would be the SCC-641(P) Setup Menu. The SCC-641(P) Setup Menu is explained in detailed in "Chapter 3 Setup Menu Overview". The instructional manual is best used when read from beginning to end, but for users wanting to read only the part they need here are the Chapter summaries.
"Chapter 1 SCC-641(P) Overview" includes a brief introduction of the SCC-641(P), part names and functions, and Switching Settings. "Chapter2 SCC-641(P) Installation" explains the installation procedures of the SCC-641(P) and provides preparation and installation environment requirements. "Chapter 3 Setup Menu Overview" presents the structure of the Setup menu for the SCC-641(P) including a detailed explanation of the functions performed in each submenu. "Appendix A SCC-641(P) Product Specifications" contains product specifications of the SCC-641(P) in itemized categories.

Approval of Standards

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interface in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient of relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio TV technician for help.

Table of contents "

Before Usage Chapter 1 SCC-641(P) Overview SCC-641(P) Introduction SCC-641(P) Location of Controls Locations of Controls - Front Locations of Controls - Back ADATER CONNECTION 1-1 1-5 1-6 1-7 1-7 1-8 1-9
- SHUTTER - AGC - WHITE BAL - SPECIAL - AUTO FOCUS - D-ZOOM - EXIT PRESET AUTO MODE - AUTO PAN - PATTERN ALARM SET OTHER SET
3-10 3-11 3-12 3-14 3-15 3-15 3-15 3-16 3-18 3-18 3-20 3-21 3-23
INITIAL SETTING...1-10 Setting RS-422A/RS-485 Termination SWITCH SETTING Chapter 2 SCC-641(P) Installations Checking Package Contents Precautions for Installation and Usage Preparing the Cable Connecting the Cable SCC-641(P) Installation Chapter 3 Setup Menu Overview Contents of Setup Menu General Structure of CAMERA Block Menu - CAMERA ID - V-SYNC - ZOOM SPEED - MOTION DET - EXIT VIDEO SET MENU - IRIS 1-11 1-12 2-1 2-2 2-3 2-5 2-6 2-7 3-1 3-2 3-5 3-5 3-6 3-6 3-7 3-8 3-9 3-9

Product specifications

Chapter 1 SCC-641(P) Overview
In this chapter we will briefly introduce the SCC-641(P) and show main functions, locations of control and Switch Setting.

SCC-641(P) Introduction

The SCC-641(P) is the best performing zoom lens integrated surveillance camera. It can be used with CCTV in banks or companies to provide high level of security. The SCC-641(P) is a high quality surveillance camera using x22 zoom lens and digital zoom IC, it can catch clear images up to 220 times. The SCC-641(P) has Low light function that enables it to take shots in the environment where there is almost no light, White Balance function that corrects the picture natural depending on the background lights, Back light Compensation function that enables objects to be seen clearly even under bright-background lighting conditions and Auto Focus function that enables it to focus according to the movement of the object. It is a multifunction camera that has all the important functions of other surveillance cameras. The SCC-641(P) uses an Alarm function for alert situations and moving camera in the direction you want, ZOOM-IN and ZOOM-OUT functions can be remote controlled.

Locations of Control

ADAPTER CONNECTION

INITIAL SETTING

CAMERA ADDRESS SETUP Dip Switch setting is same as the following example: EX) CAMERA ADDR: When it's number 1, set as follows.

SCC-641(P) Adapter BOARD

ON OFF
Setting communication Protocol. Use number 6~8 PIN of SW501 to set communication Protocol.

A :SAMSUNG(SSC-1000)

Setting BAUD RATE Use number 4 and 5 of SW501 to set BAUD RATE.
BAUD RATE 4800 BPS 9600 BPS 19200 BPS 38400 BPS

PIN 4 ON OFF ON OFF

PIN 5 ON ON OFF OFF
Setting HALF or FULL DUPLEX
HALF or FULL DUPLEX is communication method with System Controller. Use number 3 PIN of SW 501. " ON " : FULL DUPLEX. " OFF " : HALF DUPLEX. (SSC-1000)
Setting RS-422A/RS-485 termination

Receiver Address 54 55

SWITCH SETTING
SW500-1 SW500-2 SW500-3 SW500-4 SW500-5 SW500-6 SW500-7 OFF OFF OFF OFF OFF OFF OFF ON OFF OFF OFF OFF OFF OFF OFF ON OFF OFF OFF OFF OFF ON ON OFF OFF OFF OFF OFF OFF OFF ON OFF OFF OFF OFF ON OFF ON OFF OFF OFF OFF OFF ON ON OFF OFF OFF OFF ON ON ON OFF OFF OFF OFF OFF OFF OFF ON OFF OFF OFF ON OFF OFF ON OFF OFF OFF OFF ON OFF ON OFF OFF OFF ON ON OFF ON OFF OFF OFF OFF OFF ON ON ON OFF OFF ON OFF ON ON ON OFF OFF OFF ON ON ON ON OFF OFF ON ON ON ON ON OFF OFF OFF OFF OFF OFF ON OFF OFF ON OFF OFF OFF ON OFF OFF OFF ON OFF OFF ON OFF OFF ON ON OFF OFF ON OFF OFF OFF OFF ON OFF ON OFF OFF ON OFF ON OFF ON OFF OFF OFF ON ON OFF ON OFF OFF ON ON ON OFF ON OFF OFF OFF OFF OFF ON ON OFF OFF ON OFF OFF ON ON OFF OFF OFF ON OFF ON ON OFF OFF ON ON OFF ON ON OFF OFF OFF OFF ON ON ON OFF OFF ON OFF ON ON ON OFF OFF OFF ON ON ON ON OFF OFF ON ON ON ON ON OFF OFF OFF OFF OFF OFF OFF ON OFF ON OFF OFF OFF OFF ON OFF OFF ON OFF OFF OFF ON OFF ON ON OFF OFF OFF ON OFF OFF OFF ON OFF OFF ON OFF ON OFF ON OFF OFF ON OFF OFF ON ON OFF OFF ON OFF ON ON ON OFF OFF ON OFF OFF OFF OFF ON OFF ON OFF ON OFF OFF ON OFF ON OFF OFF ON OFF ON OFF ON OFF ON ON OFF ON OFF ON OFF OFF OFF ON ON OFF ON OFF ON OFF ON ON OFF ON OFF OFF ON ON ON OFF ON OFF ON ON ON ON OFF ON OFF OFF OFF OFF OFF ON ON OFF ON OFF OFF OFF ON ON OFF OFF ON OFF OFF ON ON OFF ON ON OFF OFF ON ON OFF OFF OFF ON OFF ON ON OFF ON OFF ON OFF ON ON OFF OFF ON ON OFF ON ON OFF ON ON ON OFF ON ON OFF SW500-8 OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF

As it is shown in the structure map, when Controller and RS-422A/RS-485 is connected it should be terminated according to the Cable feature of impedance on the each end of the transmitting line to transfer the signals in long distance by controlling the reflection of the signals to the lowest.

Division n < 128

Termination

SW1-ON

<RS-485 Half Duplex Organization>
Termination: using numbers 1 and 2 PIN, turn to ON and it will be terminated.
n < 128 Division SW1-ON SW2-ON

Division

<RS-422A/RS-485 Full Duplex Organization>
If more than one camera is set of same address, Communication

CAUTION

error can be occurred.

Receiver Address 114 115

SW500-1 SW500-2 OFF OFF ON OFF OFF ON ON ON OFF OFF ON OFF OFF ON ON ON OFF OFF ON OFF OFF ON ON ON OFF OFF ON OFF OFF ON ON ON OFF OFF ON OFF OFF ON ON ON OFF OFF ON OFF OFF ON ON ON OFF OFF ON OFF OFF ON ON ON OFF OFF ON OFF OFF ON ON ON OFF OFF ON OFF OFF ON ON ON OFF OFF ON OFF OFF ON ON ON OFF OFF ON OFF OFF ON ON ON OFF OFF ON OFF OFF ON ON ON OFF OFF ON OFF OFF ON ON ON OFF OFF ON OFF OFF ON ON ON OFF OFF ON OFF OFF ON ON ON
SW500-3 SW500-4 SW500-5 SW500-6 SW500-7 SW500-8 OFF ON ON ON OFF OFF OFF ON ON ON OFF OFF OFF ON ON ON OFF OFF OFF ON ON ON OFF OFF ON ON ON ON OFF OFF ON ON ON ON OFF OFF ON ON ON ON OFF OFF ON OFF OFF OFF OFF OFF OFF OFF OFF OFF ON OFF OFF OFF OFF OFF ON OFF OFF OFF OFF OFF ON OFF OFF OFF OFF OFF ON OFF ON OFF OFF OFF ON OFF ON OFF OFF OFF ON OFF ON OFF OFF OFF ON OFF ON ON OFF OFF ON OFF OFF ON OFF OFF ON OFF OFF ON OFF OFF ON OFF OFF ON OFF OFF ON OFF OFF ON OFF OFF ON OFF ON ON OFF OFF ON OFF ON ON OFF OFF ON OFF ON ON OFF OFF ON OFF ON OFF ON OFF ON OFF OFF OFF ON OFF ON OFF OFF OFF ON OFF ON OFF OFF OFF ON OFF ON OFF OFF OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON ON ON OFF ON OFF OFF ON ON OFF ON OFF OFF ON ON OFF ON OFF OFF ON ON OFF ON OFF OFF ON ON OFF ON OFF ON ON ON OFF ON OFF ON ON ON OFF ON OFF ON ON ON OFF ON OFF ON OFF OFF ON ON OFF OFF OFF OFF ON ON OFF OFF OFF OFF ON ON OFF OFF OFF OFF ON ON OFF OFF OFF OFF ON ON OFF ON OFF OFF ON ON OFF ON OFF OFF ON ON OFF ON OFF OFF ON ON OFF ON ON OFF ON ON OFF OFF ON OFF ON ON OFF OFF ON OFF ON ON OFF OFF ON OFF ON ON OFF OFF ON OFF ON ON OFF ON ON OFF ON ON OFF ON ON OFF ON ON OFF ON ON OFF ON ON OFF ON OFF ON ON ON OFF OFF OFF ON ON ON OFF OFF OFF ON ON ON OFF OFF OFF ON ON ON OFF OFF OFF ON ON ON OFF

Receiver Address 174 175

SW500-1 SW500-2 SW500-3 SW500-4 SW500-5 SW500-6 SW500-7 OFF OFF ON OFF ON ON ON ON OFF ON OFF ON ON OFF OFF ON ON OFF ON ON ON ON ON ON OFF ON ON ON OFF OFF OFF ON ON ON ON ON OFF OFF ON ON ON ON OFF ON OFF ON ON ON ON ON ON OFF ON ON ON ON OFF OFF ON ON ON ON ON ON OFF ON ON ON ON ON OFF ON ON ON ON ON ON ON ON ON ON ON ON ON OFF OFF OFF OFF OFF OFF OFF ON OFF OFF OFF OFF OFF OFF OFF ON OFF OFF OFF OFF OFF ON ON OFF OFF OFF OFF OFF OFF OFF ON OFF OFF OFF OFF ON OFF ON OFF OFF OFF OFF OFF ON ON OFF OFF OFF OFF ON ON ON OFF OFF OFF OFF OFF OFF OFF ON OFF OFF OFF ON OFF OFF ON OFF OFF OFF OFF ON OFF ON OFF OFF OFF ON ON OFF ON OFF OFF OFF OFF OFF ON ON OFF OFF OFF ON OFF ON ON OFF OFF OFF OFF ON ON ON OFF OFF OFF ON ON ON ON OFF OFF OFF OFF OFF OFF OFF ON OFF OFF ON OFF OFF OFF ON OFF OFF OFF ON OFF OFF ON OFF OFF ON ON OFF OFF ON OFF OFF OFF OFF ON OFF ON OFF OFF ON OFF ON OFF ON OFF OFF OFF ON ON OFF ON OFF OFF ON ON ON OFF ON OFF OFF OFF OFF OFF ON ON OFF OFF ON OFF OFF ON ON OFF OFF OFF ON OFF ON ON OFF OFF ON ON OFF ON ON OFF OFF OFF OFF ON ON ON OFF OFF ON OFF ON ON ON OFF OFF OFF ON ON ON ON OFF OFF ON ON ON ON ON OFF OFF OFF OFF OFF OFF OFF ON OFF ON OFF OFF OFF OFF ON OFF OFF ON OFF OFF OFF ON OFF ON ON OFF OFF OFF ON OFF OFF OFF ON OFF OFF ON OFF ON OFF ON OFF OFF ON OFF OFF ON ON OFF OFF ON OFF ON ON ON OFF OFF ON OFF OFF OFF OFF ON OFF ON OFF ON OFF OFF ON OFF ON OFF OFF ON OFF ON OFF ON OFF ON ON OFF ON OFF ON OFF OFF OFF ON ON OFF ON OFF ON OFF ON ON OFF ON OFF OFF ON ON ON OFF ON OFF ON ON ON ON OFF ON OFF

SW500-8 OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON

Receiver Address 234 235

SW500-1 SW500-2 SW500-3 SW500-4 SW500-5 SW500-6 SW500-7 OFF OFF OFF OFF ON ON OFF ON OFF OFF OFF ON ON OFF OFF ON OFF OFF ON ON OFF ON ON OFF OFF ON ON OFF OFF OFF ON OFF ON ON OFF ON OFF ON OFF ON ON OFF OFF ON ON OFF ON ON OFF ON ON ON OFF ON ON OFF OFF OFF OFF ON ON ON OFF ON OFF OFF ON ON ON OFF OFF ON OFF ON ON ON OFF ON ON OFF ON ON ON OFF OFF OFF ON ON ON ON OFF ON OFF ON ON ON ON OFF OFF ON ON ON ON ON OFF ON ON ON ON ON ON OFF OFF OFF OFF OFF OFF OFF ON ON OFF OFF OFF OFF OFF ON OFF ON OFF OFF OFF OFF ON ON ON OFF OFF OFF OFF ON OFF OFF ON OFF OFF OFF ON ON OFF ON OFF OFF OFF ON OFF ON ON OFF OFF OFF ON ON ON ON OFF OFF OFF ON OFF OFF OFF ON OFF OFF ON ON OFF OFF ON OFF OFF ON OFF ON OFF ON OFF OFF ON ON ON OFF ON OFF OFF ON OFF OFF ON ON OFF OFF ON ON OFF ON ON OFF OFF ON OFF ON ON ON OFF OFF ON ON ON ON ON OFF OFF ON OFF OFF OFF OFF ON OFF ON ON OFF OFF OFF ON OFF ON OFF ON OFF OFF ON OFF ON ON ON OFF OFF ON OFF ON OFF OFF ON OFF ON OFF ON ON OFF ON OFF ON OFF ON OFF ON ON OFF ON OFF ON ON ON ON OFF ON OFF ON OFF OFF OFF ON ON OFF ON ON OFF OFF ON ON OFF ON OFF ON OFF ON ON OFF ON ON ON OFF ON ON OFF ON OFF OFF ON ON ON OFF ON ON OFF ON ON ON OFF ON OFF ON ON ON ON OFF ON ON ON ON ON ON OFF ON OFF OFF OFF OFF OFF ON ON ON OFF OFF OFF OFF ON ON OFF ON OFF OFF OFF ON ON ON ON OFF OFF OFF ON ON OFF OFF ON OFF OFF ON ON ON OFF ON OFF OFF ON ON OFF ON ON OFF OFF ON ON ON ON ON OFF OFF ON ON OFF OFF OFF ON OFF ON ON ON OFF OFF ON OFF ON ON OFF ON OFF ON OFF ON ON ON ON OFF ON OFF ON ON
SW500-8 ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON

Receiver Address 254 255

SW500-1 OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON
SW500-2 SW500-3 SW500-4 SW500-5 SW500-6 OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON ON ON ON ON OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF ON ON ON ON ON ON ON ON OFF OFF OFF OFF OFF OFF OFF OFF ON ON ON ON ON ON ON ON OFF OFF OFF OFF ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON

SW500-7 SW500-8 ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON

Before Installing

Chapter 2 SCC-641(P) Installation
In this chapter we will look over the checkpoints before installation, installation environmental requirements, and precautions during the installation of the SCC-641(P). After that we'll show the actual installation of the SCC-641(P) and cable connections.
Checking Package Contents
Please check that all components listed below are included in the package:

Power Adapter SCC-641(P)

Owners Instructions

Bracket Anchor

Cover Body

Camera Holder

Precautions for Installation and Usage.
Do not attempt to disassemble the SCC-641(P). There is a danger of electric shock if the screws or cover are removed. We strongly recommend that users avoid handling the interior part of the SCC-641(P). If it becomes necessary to inspect the inside, please contact a distributor. Handle the SCC-641(P) with care. Although the SCC-641(P) is a durable product, handling the product carefully will lengthen its operating life and prevent failures. Avoid shaking or directly impacting the camera to prevent damage to the product and handle and store properly. Do not expose the SCC-641(P) to rain or moisture or operate it in wet area. If the SCC-641(P) comes in contact with water, turn the power switch off immediately and contact a distributor. Moisture can damage the SCC-641(P) and increases the danger of electric shock. Do not use strong detergents or abrasive detergents to clean the SCC-641(P) body. If the SCC-641(P) body becomes dirty, use a dry cloth to clean the unit. In case the dirt is hard to remove, use a mild detergent and wipe gently.
Never face the SCC-641(P) towards the sun. Whether the SCC-641(P) is in use or not, never face it towards the sun. Use with caution when operating the SCC-641(P) in the vicinity of spotlights or other bright lights and light reflecting objects. The SCC-641(P) should be operated in a stable environment. Acceptable operating conditions are listed below:
Temperature : -10 +50 (14 Humidity level : 90% or less
Proper electric power should be used according to the specifications of the SCC-641(P) power supply system.
Power Consumed : 18W Power Input : 24VAC, 1.5A

Preparing the Cables

Cable Connection
1. First, connect one end of the BNC video cable connector to the Video Output Terminal (VIDEO OUT)
To install and use the SCC-641(P), the following cables should be prepared.
2. Then, connect the other end of the connector to the Video Input Terminal of the monitor.

Power Adapter Cable

The cable connected to the Power input terminal of the SCC-641(P) is shown below with a rated voltage of 24VAC and ampacity of 15A.
3. Now connect the Power Adapter Cable. Use a driver to screw one part of the two lines of Power Adapter to Power Input Terminal of the SCC-641(P).

Video Cable

The SCC-641(P)'s cable is a BNC Cable for connecting the video-output terminal to the video-input terminal of the monitor.
4. Adjust the switch below the Power Adapter to the proper voltage. Then, connect the Power Adapter's plug to the Power Connector. 5. Connect the Remote Control Terminal of the SCC-641(P) and the external Controller.
4. [Figure 3,4] Connect the various cables to the CAMERA ADAPTER. (See page 2-6)

SCC-641(P) Installation

1. [Figure 1] Install the structure on the ceiling. (Refer to Installation reference for the Length of the structure) * Built in by the builder of the structure
[Figure 1] [Figure 3] [Figure 4]
5. [Figure 5] Match the BRKT-ANCHOR and CAMERA ADAPTER and use 4screws (PH M4x8) to assemble them.

Lenght of ceiling Hole

2. Make a hole in the ceiling where the camera will be installed. (The hole should be about 180) [Figure 5]
3. [Figure 2] Assemble the BRKT-ANCHOR on the ceiling and screw the 4 bolts in.

[Figure 2]

6. [Figure 6] Match the 3 holes on the back of the CAMERA and the CONNECTOR and turn it left about 15 degrees. (Check the sound of LOCKING and that the LEVER-LOCKING is in place) * Use the screws (BH M3XL8) to connect the CAMERA and the ADAPTER so they don't move.
Chapter 3 Setup Menu Overview

[Figure 6]

In this chapter, we will look over the Setup Menu of the SCC-641(P), First we'll look over the overall structure of the Setup Menu, and then we'll look at the functions of each menu.
7. [Figure 7] Assemble the COVER-DOME onto the DOME.

[Figure 7]

Structure of the Setup Menu
ALARM SET CAMERA CAMERA ID V-SYNC ZOOM SPEED MOTION DET EXIT ON./OFF INT/LINE. 1/2/3/4 ON./OFF QUIT/SAVE/PRESET ALARM PRIORITY SET ALARM1 1~4 ALARM2 1~4 ALARM3 1~4 ALARM4 1~4 EXIT QUIT/SAVE ALARM1 ALARM2 ALARM3 ALARM4 EXIT ALARM1 ALARM2 ALARM3 ALARM4 MOTION EXIT ALARM1 ALARM2 ALARM3 ALARM4 MOTION EXIT OUT1 OUT2 OUT3 EXIT NO/NC/OFF NO/NC/OFF NO/NC/OFF NO/NC/OFF QUIT/SAVE 1~3 1~3 1~3 1~3 1~3 QUIT/SAVE OFF/1~3/HALF1/HALF2/FULL OFF/1~3/HALF1/HALF2/FULL OFF/1~3/HALF1/HALF2/FULL OFF/1~3/HALF1/HALF2/FULL OFF/1~3/HALF1/HALF2/FULL QUIT/SAVE

ALARM IN SET

CAMERA ID V-SYNC ZOOM SPEED MOTION DET
In MOTION DET, you can set the Motion Detection function, Motion Detection Sensitivity, and the Area of Motion Detection. If the Motion Detection function is set, the movement of an intruder can be detected. When motion is detected, it sets off the Alarm signal of the Controller.
(CAMERA SET) (MOTION DET) OFF INT 3 ON.
Select LINE and press [Enter]. You will see the LINE LOCK submenu where you can adjust the phase of the LINE LOCK. You can use the PHASE menu of the LINE LOCK submenu to assign as much PHASE as you want.
AREA SENSITIVITY RET USER. LOW
EXIT (CAMERA SET) CAMERA ID V-SYNC ZOOM SPEED MOTION DET OFF LINE. 3 OFF

(LINE LOCK)

Select ON and press [Enter] you will see the "MOTION DET" submenu. The "AREA" menu, the screen area where the Motion Detection function is going to be applied, can be set as
PRESET or USER. If the "AREA" menu is set to PRESET, the Motion Detection function will be applied to the basic part of the SCC-641(P)'s factory default presets. Set the AREA menu
PHASE (000) RET ---- ----
to USER and press [ENTER], the user can choose the size of the area and location where the Motion Detection function should be applied.When the area is not blinking, you can use the

ZOOM SPEED

In the ZOOM SPEED menu you can select the speed of the ZOOM Key (Tele/Wide). Use the [Left] or [Right] keys in the ZOOM SPEED menu to selcet the speed. 1 : Magnification x 22 takes about 17 seconds Slowest speed 2 : Magnification x 22 takes about 10 seconds Low speed 3 : Magnification x 22 takes about 6 seconds High speed 4 : Magnification x 22 takes about 3 seconds Fastest speed
(CAMERA SET) CAMERA ID V-SYNC ZOOM SPEED MOTION DET OFF INT 3 OFF
[Left, Right, Up, Down] keys to move and set the position. If you press [5] when the position is not blinking, it will start to blink and you can use the [Left, Right, Up, Down] keys to set the size of the area. Use the [5] and [Left, Right, Up, Down] keys to set the position and size of the Motion Detection Area.If you press [ENTER] once more, you will exit the "AREA" setting menu.Use the "SENSITIVITY" menu to set the sensitivity of the MOTION Detection.The Higher it is set, the more sensitive the Motion Detection moves.

- 3200 K : Set color temperature to 3200 K - 5600 K : Set color temperature to 5600 K - User : Set the appropriate value in the RED and BULE graph.

5000 K

(VIDEO SET) (AWB/MANU) ALC. OFF ON MANU. OFF AF OFF QUIT
4000 K Fluorescent lamp 3000 K Halogen lamp
IRIS SHUTTER AGC WHITE BAL SPECIAL AUTO FOCUS D-ZOOM EXIT
PRESET OFF(USER). RED (00) ---- ---BLUE (00) ---- ---RET
2000 K Tungsten lamp 1000 K Candlelight

SPECIAL

In the SPECIAL menu, POSI/NEGA, PIP, Mirror, and vertical and horizontal detail level can be adjusted. - POSI/NEGA: Video output signal is outputted normal/reverse. - PIP(Picture in Picture): When Digital Zoom is activated, the 1/16 minimized screen will be shown. - Mirror: Reverse the video output signal. - H-DTL: Adjust Horizontal Detail Level. - V-DTL: Adjust Vertical Detail Level.

AUTO FOCUS

In the AUTO FOCUS MENU, the Focus method can be set to AF, MF, or ONEAF. - AF: With AUTO FOCUS MODE, you can monitor the screen continuously and it will focus automatically. While moving the zoom keys, it will automatically focus so FOCUS key input is not necessary. - MF: In MANUAL FOCUS MODE the user adjusts the Focus manually. - ONEAF: In ONEAF mode the SCC-641(P) auto focuses only while moving/stopping. When the SCC-641(P) is not moving it is same as MF mode and when it's moving/stopping it's the same as AF mode. Use the left/right keys to select AF, MF or ONEAF in the AUTO FOCUS menu.
(VIDEO SET) IRIS SHUTTER AGC WHITE BAL SPECIAL AUTO FOCUS D-ZOOM EXIT + OFF OFF ---- ------ ----ALC. OFF ON ATW OFF AF OFF QUIT
Select ON and press [ENTER], the "SPECIAL" submenu to choose the special functions will be shown.
(VIDEO SET) IRIS SHUTTER AGC WHITE BAL SPECIAL AUTO FOCUS D-ZOOM EXIT ALC. OFF ON ATW ON. AF OFF QUIT (SPECIAL)
POSI/NEGA PIP MIRROR H-DTL ( 0) V-DTL ( 0) RET

D-ZOOM

In the D-ZOOM menu you can choose the Digital Zoom magnification. You can select a magnification from OFF to 10 times.
To choose functions use the left/right keys to select an item.In the PIP menu, select ON and press [ENTER]. Use the [left, right, up, down] keys to set the location of the PIP.
When Digital Zoom is selected at 10 times, it is the Optic Zoom for 22 times the size so the camera can film at up to 220 times. Use the [left, right] keys to select the magnification in the D-ZOOM menu.
PIP does not function in low speed SHUTTER MODE. When Mirror is functioning, Mirror does not function in the PIP windows.

(SPECIAL) (VIDEO SET) IRIS SHUTTER AGC WHITE BAL SPECIAL AUTO FOCUS D-ZOOM EXIT PIP Screen ALC. OFF ON ATW OFF AF OFF QUIT (VIDEO SET) IRIS SHUTTER AGC WHITE BAL SPECIAL AUTO FOCUS D-ZOOM EXIT ALC. OFF ON ATW OFF AF X10 QUIT
POSI/NEGA + PIP ON MIRROR OFF H-DTL (00) ---- ---V-DTL (00) ---- ---RET
It's the same as the EXIT function of the CAMERA SET menu.
A total of 128 presets are available including the selection of PAN/TILT location and Zoom/Focus, and setting up screen conditions and monitoring. (0 ~ 127) Among the 128 PRESETS PRESET 0: HOME POSITION, PRESET 1: ALARM1, PRESET 2: ALARM2, PRESET 3: ALARM3, PRESET 4: ALARM4,PRESET 5: set as special preset corresponding MOTION.

POSITION SET

From "POSITION SET " press [ENTER] to get into the PAN/TILT, FOCUS/ZOOM SET screen to set the PAN/TILT location and FOCUS/ZOOM condition then press [ENTER] to return to a higher menu.
PRESET NO.0 SET PAN/TILT SET ZOOM/FOCUS
This is the screen setting function for each PRESET.

** MAIN MENU **

Refer to the explanation under "VIDEO SET menu".
(PRESET MAP) 30 ID RET 31 : PRESET 0
CAMERA. VIDEO SET. PRESET. AUTO MODE. ALARM SET. OTHER SET.

PRESET ID

This is the ID set up function for each PRESET. It can be set up to 12 characters using the left, right, up, and down keys. The ID location can be set in the submenu of "LOCATION."
PRESET NO.0 ID A BCDEFGHIJKL M N O PQ R S T U V W X YZ:! - + * ()/ SP SP LOCATION. RET PRESET 0.

PRESET NO.0

PRESET NO.0 POSITION SET. VIDEO SET ON. PRESET ID ON. SCAN ON DWELL TIME 2S
This function sets up for movement or no movement in "SCAN" motion. When it's PRESET to "ON" it includes SCAN motion and to "OFF" no movement.
POSITION SET. VIDEO SET. ON. PRESET ID ON. SCAN ON DWELL TIME 2S

DWELL TIME

This is a function setting for the DWELL TIME of the PRESET location in "SCAN" motion. It can set DWELL TIME From 1 ~ 60 Sec.
"QUIT": Does not save the selected information and returns to a higher menu. "SAVE": Do saves the selected information and returns to a higher menu. "DEL" : Deletes the selected information and restores the DEFAULT. Then returns to a higher menu.
AUTO PAN and PATTERN functions are in AUTO MODE.

END SET

SET END!

"END SET" gets into the END SET setup screen by

AUTO PAN

After selecting the locations of two points (PAN/TILT) of START and END, it loops continuously in the set up SPEED.
pressing [ENTER]. Adjust PAN/TILT location and press [ENTER] to return to a higher menu.
(AUTO MODE) AUTO PAN. PATTERN SET 1.

DIRECTION

Set up the movement direction of the START to END location (PAN location standard)

"RIGHT " :

"LEFT " :
AUTO PAN START SET. END SET. DIRECTION RIGHT ENDLESS ON SPEED STEP5 DWELL TIME 2 S EXIT QUIT

ENDLESS

This is a 360-degree rotation function that only stops for the DWELL TIME in the START and END positions. It can be set to "ON" or "OFF".

START SET SPEED

From "START SET." get into the START SET setup screen by pressing [ENTER]. After selecting the locations of PAN/TILT location, press [ENTER] again to return to higher menu.

SET START!

This is a setting function for movement speed setup. It can be set from STEP1 to STEP64.
This is a function for setting up the time to stay in the START to END position.

PATTERN

This is a replay function so that the MANUAL functions such as PAN, TILT, ZOOM, and FOCUS are played for 30 seconds.

ALARM SET

It consists of 4 ALARM INPUTs and 3 ALARM OUTs.It can sense an ALARM input from exterior SENSORs and it performs with PRESET or PATTERN function and outputs the ALARM OUT signals. It recognizes the ALARM signal input as an ALARM signal when it continnes more than

(AUTO MODE)

150ms for a time and each ALARM movement time is decided depending on it's correspondence to the DWELL TIME of the PRESET and PATTERN connected.
( ALARM SET) ** MAIN MENU ** ALARM PRIORITY SET. ALARM IN SET. ALARM OUT SET. ALARM PATTERN SET. AUX OUT CONTROL.

AUTO PAN. PATTERN SET 1.

[Enter]
RET CAMERA. VIDEO SET. PRESET. AUTO MODE. ALARM SET. OTHER SET.

PATTERN1 SET

ALARM PRIORITY SET
Press [Enter] Sets the priority of the 4 ALARM inputs and corresponds to priority.The priority of the DEFAULT is ALARM1: 1, ALARM2: 2, ALARM 3: 3, ALARM: 4, MOTION: 5.If the ALARM is working at the same time and the priority is the same, it will operate according to the DEFAULT priority.While the ALARM is working, it cannot detect MOTION. PATTERN can be set to 3. Choose 1, 2, or 3 with the left or right key in the "PATTERN SET" and press [ENTER] to get into the PATTERN set up screen. From the moment "PATTERN 1 SET" is gone for 30 seconds, it memorizes the MANUAL movements and after 30 seconds it will return to a higher menu. If you want to finish set up before the 30-second ends, press [ENTER].

ALARM PRIORITY ALARM1 ALARM2 ALARM3 ALARM4
Set the TYPE to "NO" (Normal Open), "NC" (Normal Close), or "OFF" depending on the features of the SENSOR connected.
ALARM IN ALARM1 ALARM2 ALARM3 ALARM4 NO NC NO NC

ALARM OUT

Each ALARM input corresponds to one of the 3 ALARM OUT. < The ALARM3 is designed as the Relay OUT >
ALARM OUT ALARM1 ALARM2 ALARM3 ALARM4 MOTION 1

OTHER SET

HOME RETURN
When there is no KEY input or other movement for a certain time, the camera moves to
the HOME location automatically. The HOME location is assigned PRESET 0.

ALARM PATTERN

** MAIN MENU ** (OTHER SET) HOME RETURN AUTO FLIP OFF ON
This sets the operation of PATTERN movements when inputting ALARM. When the ALARM is inputted the correspondence will be as follows: ALARM1 input to PRESET 1, ALARM 2 input to PRESET 2, ALARM3 input to PRESET 3, ALARM 4 input to PRESET 4, and MOTION input to PRESET 5. When the ALARM is working, it will stay in the PRESET location corresponding the ALARM for the DWELL TIME and the ALARM connected to the PATTERN will continuously operate the PATTERN movements. The OFF in the Setup Menu does not operate the PATTERN, and it means 1 PATTERN1, 2 PATTERN 2, 3 PATTERN 3, continuous motion of HALF1 Pattern 2 + PATTERN 3 PATTERN 1 + PATTERN 2, continuous motion of HALF 2 and continuous motion of FULL OFF 1 MIN 2 MIN 3 MIN ~ 60MIN 12HOUR 2HOUR ~ 4HOUR
EXIT QUIT ALARM PATTERN ALARM1 ALARM2 ALARM3 ALARM4 MOTION OFF OFF 3 CAMERA. VIDEO SET. PRESET. AUTO MODE. ALARM SET. OTHER SET.
SET UP TIME FOR HOME RETURN: OFF: HOME RETURN function cancellation

AUTO FLIP

When operating the Tilt to the 90 limit using the Joystick, the camera PAN automatically revolves 180 showing the opposite area of the Tilt area.It gives the effect of extending the Tilt operating area 180.
PATTERN 1+PATTERN2+PATTERN3.

(OTHER SET)

This sets the ALARM OUT motion to continue or act only when the ALARM is working. If it is set to OFF the ALARM OUT motion will operate only when the ALARM is set off (Active "Low"), and if it's set to ON, the ALARM OUT will always operate regardless of the ALARM.

REMOTE CONTROL

Operation Temperature Operation Humidity SIZE Weight Altitude

Cautions

The copyright of the manual belongs to Samsung Electronics Co., Ltd. Without the permission of Samsung Electronics it cannot be reproduced electronically, mechanically, audibly, or by any other method. This manual will be modified according to product enhancements.