Digital Video Security System Technology CONTROLLERS

SNC-L200 / L200W

Wired Network Camera/Wireless (Wi-Fi) Network Camera

SCQ-041AP

4 Channel Digital Color Quad Switcher

Features

1/4" 320,000 pixels CMOS Preset function (Max=8) Remote Pan/Tilt contol Power Pan (50) /Tilt (+10 ~ -40) Flash LED for night vision PIR Sensor Pre Alarm / Auto Alarm Privacy function UPnP supportable Supports various protocol (TCP/IP UDP ARP HTTP SMTP FTP Telnet, DHCP PPPoE) , , , , , , , Supports WAP 2.0 (USA) IEEE 802.11b (SNC-L200W) Remote Recording with Free Multi-Viewer Management Software; Up to 16 CH Recording, 1CH Playback

Dimensions (unit : mm)

105 63.5 44

Front Panel

SNC-L200

SNC-L200W

Specifications
Camera Image Sensor White Balance Focus Min. Scene Illumination Pan/Tilt Range Pan/Tilt Speed Number of Preset Flash LED-LED Lens Degree Flash LED-Lux/Range PIR Sensor-Left/Right PIR Sensor-Up/Down PIR Sensor-Range Network Connection Network Service Network Protocol Image Compression Video Streaming Format Resolition Frame Rate-640x480 Frame Rate-320x240 File Size-640x480 File Size-320x240 File Size160x120 Authentification IP Router(AP)-LinkSys IP Router(AP)-Netgear IP Router(AP)-D-Link Simultaneous Viewer Pre-Alarm Camera Recording Frame Rate Control Free DDNS Compatible WAP-O.S WAP-WAP Version WAP-Browser WAP-display size WAP-Video Codec WAP-Service area WAP-URL support Wireless-Protocol Wireless-Frequency Wireless-Range Wireless-Throughput 1/4" 320,000 Pixels CMOS Pixels Auto Fixed 1m ~ Infinity 1 ~ 10,000 Lux Pan(50 Left ~ 50 Right)/Tilt(40 Down~ 10 Up) 50 /Sec 8 ea Lux/3 m 3m 10/100Base-T Fixed IP Cable Modem, ADSL, DHCP IP Router , , TCP/IP UDP ARP HTTP SMTP FTP Telnet, DHCP PPPoE , , , , , , , JPEG M-JPEG 640x480, 320x240, 160xfps 30 fps 12KB(Low), 17KB(Normal), 25KB(High) 4KB(Low), 7KB(Normal), 9KB(High) 2KB(Low), 3KB(Normal), 4KB(High) ID/Password Authentification WRT54G WGR614v4 DI-624+ 10 Persons yes yes (save on users PC via network) 1.0/5.0/10.0/15.0/30.0 Fps yes (A free Service that require upgrade) Embedded Linux WAP2.0 open browser 160x120, 320x240 M-JPEG USA yes
1/4" 320,000 Pixels CMOS Pixels Auto Fixed 1m ~ Infinity 1 ~ 10,000 Lux Pan(50 Left ~ 50 Right)/Tilt(40 Down~ 10 Up) 50 /Sec 8 ea Lux/3 m 3m 10/100Base-T Fixed IP Cable Modem, ADSL, DHCP IP Router , , TCP/IP UDP ARP HTTP SMTP FTP Telnet, DHCP PPPoE , , , , , , , JPEG M-JPEG 640x480, 320x240, 160xfps 30 fps 12KB(Low), 17KB(Normal), 25KB(High) 4KB(Low), 7KB(Normal), 9KB(High) 2KB(Low), 3KB(Normal), 4KB(High) ID/Password Authentification WRT54G WGR614v4 DI-624+ 10 Persons yes yes (save on users PC via network) 1.0/5.0/10.0/15.0/30.0 Fps yes (A free Service that require upgrade) Embedded Linux WAP2.0 open browser 160x120, 320x240 M-JPEG USA yes IEEE 802.1 1b 2.4 Ghz 100 ~ 150 feet 1 Mbps 1 8.4V DC, 1A 5W 400g 105 x 75 x 63.5 mm

Network & Server

Summary
SCQ-041AP is a digital 4-screen display device that enables the composite display of up to 4 Video signals from external devices such as the surveillance camera on a single monitor screen. It enables the initial encryption of up to 8 alphanumeric characters for each channel on a connected monitor screen and allows the wider range of application design by offering the time display, external alarm signal, and remote controlling. SCQ-041AP is suitable for - Police station - Corporate security - Factory facility - Apartment guard business - Department store - School (Educational organization) safety
Samsung Security System l 89
Power Requirement Power Consumption Weight-Net Dimension(WxHxD)-Net
8.4V DC, 1A 5W 400g 105 x 75 x 48 mm
* "P" indicates PAL model & "N" or no specific alphabet after the model name indicates NTSC model.

RF Radiation Exposure Statement
This equipment complies with FCC RF Radiation Exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2

Features

The Netcam can be installed in any place you want at domestic, business or industrial premises, and provides real-time security moving images over the Internet, allowing remote controlling for security and monitoring. The NetcamW is a wireless network camera adopting wireless network technology, which allows users to access a security camera without LAN cable connection.

Night Flash

You can monitor the environment at nighttime or in a dark room by using flash.
Passive Infrared (PIR)Sensor
Automatically detects and shoot any motion from intrusion, and sends it by E-mail. You can use this function when you leave the house or return from work.
1/4" 320,000-pixel CMOS
Provides high-quality video of 320,000-pixels (pixel is a number of dots comprising an image)by adopting high-resolution CMOS.

Pre-Alarm Pan &Tilt

Moves the lens up and down and left and right, allowing shooting of every corner in every direction. When motion is detected over the screen, both the detected image and the image before motion detection is sent to the E-mail address pre-set by the user (You can set the number of before and after-alarm images sent from the menu).

Power Pan &Tilt

When you select a desired spot by clicking, the camera lens moves the spot to the center of the screen. You can adjust movement over a screen more easily and accurately.

PRIVACY

Privacy Protection
You can press the Privacy Button of the Netcam(W) if you do not want to shoot videos. Then the lens rotates to uncovered range, and the screen turns black. If you press the button again, Privacy Mode is displayed on the black screen.

Reset Button

Netcam(W) User s Manual (Warranty Included) Installation Screws/Fix labels/ Power Adapter (DC Power Cord EMI suppression EMI suppression ferrite core ferrite core CD Anchor (16X3)2 8.4V/1A)(DC8.4V/1A) for Power Cable for LAN Cable
Detects and records motion of a human or an animal by using an infrared ray. - Selects perform or cancel by using the PIR Sensor Button of Smart/Multi Viewer. - Flash can be turned on in link with the PIR Sensor.
Range of detection left and right Range of detection up and down

Privacy

Turns the lens out of the performance range to prevent shooting for privacy.
Press the Privacy Button.
- Every time you press the button, [the lens moves out of the performance range Privacy Mode is displayed and video is not transmitted restore to the previous state ] process is repeated.

Distance and Range

Distance of Detection : Up to 3m Range of detection (up and down) : Around 85 Range of detection (left and right) : Around 40 The left and right range of detection may change if motion is fast. Avoid exposing this product to direct sunlight, air conditioner or heater, high or cold temperature, humidity, oil, smoke and glass when installing the product. The Sensor may malfunction.
When the product is not in normal conditions, you can set the values to factory default.
Press the Reset Button on the back for more than 5 seconds.
- Refer to the title of each component for the location of the Reset Button (page 12). - All the values are restored to factory default settings, and the system is rebooted. Use the product after some 2 minutes.
You can monitor the environment even in a dark room by using flash. - Turns on the flash by using the Flash button of the Smart/Multi Viewer. - Flash can be turned on in link with the PIR Sensor. - Flash is turned on for 5 seconds and off for 30 seconds. Even i f you click the Flash Button in 30 seconds, flash is not turned on. - Flash is also turned on for 5 seconds and off for 30 seconds when using the PIR Sensor.
Range of light emitting left and right Range of light emitting up and down
Do not use this function unless necessary. Stored values such as the network settings, registered users, the title of the Netcam(W), firmware upgrades are all switched to Warning factory default settings.

10. Clear Button: Deletes the list of the Netcam(W) s from the SNC Installer List. 11. Manual Set Button: The user enters the network settings of the Netcam(W). 12. Auto Local Set Button: The SNC Installer automatically sets the network settings of the Netcam(W). 13. Internet Set (UPnP)Button: Port-forward to enable access to the Netcam(W) from the external Internet. 14. Close Button: Closes the SNC Installer window. 15. URL via internet: The URL address used for access from the external Internet.

Setting the Network

You can set a variety of network settings such as IP address and UPnP by using the SNC Installer program. You can choose between <Auto Local Set>and <Manual Set>.

Auto Setting the Network

The SNC Installer searches and automatically allocates available IP and Subnet Masks over the user network by using the Auto Local Set.
5 When the Auto Local Set is completed, the Internet Set (UPnP)window appears as follows.
- Click Yes to set up connection over the Internet (refer to pages 38 to 40 for setup). - Click No to not set up connection over the Internet. Auto Local Set Screen 5 6
1 Click the Auto Local Set Button on the bottom of the SNC Installer screen. 2 Enter a proper value for each item. Apply the set values to the Netcam(W), 3 and save the values by entering the Root password and clicking the Set Button in the Save Configuration Option.
- Click the Cancel Button to cancel the set value.

4 Click the Yes Button.

- The following screen appears for about 2 minutes.
1. Server Name: Set the name of the Netcam(W).You can enter up to 20 letters (alphabet and Roman Numerals). You cannot use special characters such as #, , and:. 2. IP Address: Automatically enter the IP available in the user network environment. 3. Netmask: Automatically enter the Subnet Mask of the IP router (router or wireless router). 4. Wireless Enable/Wireless Disable(SNC-L200W Only): Choose the Wireless Enable when using wireless connection of the NetcamW. Choose the Wireless Disabled when not using wireless connection. Warning IP collision may occur between Netcam(W) and the PC if a firewall is installed over a single network. Exclude the IP of the PC with the firewall if collision occurs. 5. AP Information (SNC-L200W Only) :ESSID: Enter the (E)SSID used by the wireless router to be connected. Press the Scan AP Button next to the item, and the list of (E)SSIDs the wireless routers presently available from the NetcamW appears. AUTH MODE: Choose the AUTH Mode of the wireless router to be connected between the Open System and the Shared Key. WEP: Select WEP when the wireless router to be connected uses the WEP wireless security settings. Mode: Select the type of the WEP Key set for the wireless router to be connected. KEY: Enter the value of the WEP Key set for the wireless router to be connected. 6. Root password: The password is defaulted to root. Enter a new password if the current one is changed. 29

1. Server Name: Set the name of the Netcam(W). You can enter up to 20 letters (alphabet and Arabian numbers). You cannot use special characters such as #, , and :. 2. HTTP Port: Enter the port value of the Netcam(W) set during the Port Forwarding Setup of the IP router (router or wireless router) 3. IP Type: Select the type of IP Setup of the Netcam(W) in the IP router (or wireless router)(Usually select the Static when using an IP router).

Port Forwarding

Port Forwarding assigns port numbers to each network device (including the Netcam(W) and PC)connected to the local network comprising of IP routers (or wireless routers), in order to connect the Global IP to the Private IP.
After user authorization, a page that sets the display of the Netcam(W) Icon in the Port Forwarding and the My Network Environment appears. 3 Set the proper value for each item, and click the Apply Button.

IP Router

Click 1 Click the Internet Set ((UPnP)Button on the bottom of the SNC Installer screen. 2 Enter the user name and password, and click the OK button.
- Enter the new password when you have changed the user password from <Smart>to <Admin.Password>. (Default settings:ID-root, Password-root) Warning
The PC environment supporting UPnP functions is available with Windows XP Service Pack 2 or higher versions.
1 The results of port forwarding appear in the UPnP Portmapping Result screen.
- Access the address displayed in the results to be connected with an external network. - Check the URL or the external access, and click the Close Button.
UPnP Configuration Screen
2 Search the set values again by clicking the Search Button on the bottom of the SNC Installer screen.
- The Success(W) is displayed in the Status if the network is successfully connected. - When using wireless Netcam(W), pull out the LAN cable and close the cover after settings.
When accessing a local network, use the address displayed as the Camera s address for Local Network Access of the UPnP Status. When accessing an external network, use the address displayed as Camera s address for Access via Internet.
1. Port Forwarding: Select the method of allocating port numbers. Disable means no allocating of port numbers. Enable means auto allocating of port numbers. User Define means the user s entering port numbers. 2. Display shortcut Icon in My Network Places: Decides whether the Netcam(W) icon will be displayed in the My Network Environment. 3. Status: Displays the status of the UPnP. When succeeding, Success is displayed. When failing, the Error is displayed. 4. External Port No.: Displays the allocated port number. 5. Router Global Address: Displays the Global IP address of the router. 6. Camera s address for Local Network Access: Displays the address with which the user can access the Netcam(W) over the current network. 7. Camera s address for Access via Internet: Displays the address with which the user can access the Netcam(W) via the Internet.

Installing the ActiveX Control
A security warning window may appear when you access the Netcam(W) Website for the first time. In this case, you must install the Active Control program to view video from the Smart Viewer.
For Windows 2000/Windows XP
Click the Yes Button when the following security warning window appears.
1 Run Internet Explorer. 2 Enter http: //Private_IP address: port number in the URL, and press the Enter Button on the keyboard.
- The Smart Viewer Screen appears. - Ex)http://168.219.13.197:8080
For Windows XP Service Pack 2
1 Click the Installation Message when the following security warning window appears.
Manually Installing the Activex Control
1 Click the Smart Viewer For Network Camera.
Click 2 Click the ActiveX Control Install.
Click 2 Click the Down Load Button. 3 Click the Execute Button.
Click 3 Click the Install Button when a security warning window appears. Click Click 4 Click the Install Button.
Note The download time for the ActiveX Control program may vary depending on the network environment.

Using the Smart Viewer

You can use a variety of features such as video monitoring, record, capture and playback with the Smart Viewer.

Smart Viewer Screen 3 4

6. Preset Operation Button: Move when the lens relocates to the Preset direction. Preset Delete Button: Delete the stored Preset settings. Preset Store Button: Store the Preset settings. 7. Lens Direction Button (Pan &Tilt): Move the lens freely with 8 direction buttons. Locate the lens to the center position by clicking the central button. 8. Flash Button: Turn on flash (turned on for 5 seconds and off for 30 seconds) 9. PIR Button: Enable or disenable Passive Infrared (PIR)functions. 10. Storage Route Button: Change the storage route of record files. 11. Capture Button: Capture selected images in JPEG files. 12. Record Button: Record Video.
13. Playback Button: Play back recorded files. 14. Record Stop Button: Stop recording. 15. Screen Size Button: Adjust the image screen to desired size.
When you select a desired spot by clicking,the camera lens moves the spot to the center of the screen.
1. ActiveX Control Download: Click when installing the ActiveX Control program manually. 2. Smart Viewer Tab: You can video-monitor. 3. Smart Setting Tab: You can set the network over the Web. 4. Date Indicator: Display the day/month/year/time of monitoring. 5. Preset Number: You can choose a Preset Setting Number between 1 to 8.

Passive Infrared (PIR)

Detects and records motion of a human or an animal by using an infrared ray and captured images.
To Set Preset You can store up to 8 lens directions,thereby restoring the lens to the originally stored position after movement.

Click the PRI Button.

1 Click the Storage Route Button(
- The Select the Folder screen appears, and you can check the storage route.
2 Change the storage route and click the Select Button.
- The folder path is changed as you choose.
Note 48 Files are stored in the changed folder even when you close the Smart Viewer and access again. 49

Stop Recorded Files

Click the Stop Button(
)on the Simple player screen.

Print Playback Images

1 Click the Print Button when the image you want to print appears ( ). - The Print screen appears.
When the number of file appears in.fjp, it means it is a moving image file.When it appears in.jpg, it is a capture file.

Capture Playback Images

1 Click the Pause Button ( ) when the image you want to capture appears, and click the Snapshot Button ( ).
- The Store File screen appears.
2 Enter the name of the file, and click the Store Button.
- The file is stored in JPEG.
2 Click the Memo Button. - Enter information for the print,and

click the OK Button.

3 Click the Setup Button.
- Click the OK Button after printer settings, and the image is printed.
- The image is printed after clicking the Print Button, when you do not need to set the print.

Setting the Smart Viewer

You can set a variety of menus such as system, network, administrator settings and firmware upgrade over the Netcam(W) Website.

Simple Player Screen

Menu Bar
Click the Smart Setting Tab in the Smart Viewer Screen.
1. Open Button: Open files to be played back. 2. Playback Button: Play back files. Reverse Playback Button: Reverse playback files. Pause Button: Stop playback for seconds. Stop Button: Stop playback. (the screen appears at the beginning of the playback file) Previous Image Button: View the previous images cut by cut in Pause mode. Next Image Button: View the following images cut by cut in Pause mode. Previous File Button: Move to the previous file. Next File Button: Move to the next file. 3. Playback Speed Button: Set the playback speed faster or slower. (X0.1,X0.2,X0.5,X1,X2,X4,X8,X10) 4. Enlarge Button:Enlarge images. Contract Button: Contract images. Original Size Button: View images in original size. 5. Snapshot Button: Capture playback images in JPEG files. 6. Print Button: Print images. 7. Scroll Bar: Move the playback position by moving the scroll bar with a mouse. You can move to the image you want in Stop or Pause mode. 52

5 Enter the User Name. 6 Click the Apply Button.
< How to Change User Password > 1 Select the Edit by clicking.

changed.

3 Enter a new password. 4 Enter the password again for
1 Image Size: Select the size of transmitted images from 160 X 120, 32 0X 240 and

640 X 480.

2 Image Quality: Set the resolution of transmitted images from High, 7
Normal and Low. Hue: Set the hue tone from 10 to 10. Saturation: Set the saturation from 10 to 10. Contrast: Set the contrast from 10 to 10. Brightness: Set the brightness from 10 to 10. Privacy Control: Privacy Control: Privacy 1 will deactivate privacy mode. It does not operate in Privacy 2. 57

Network Configuration

Alarm Notification Capture images and send them via E-mail when a motion is detected by PIR.
< Network Configuration Sub Menu >
1 Service: Set whether to enable this service. Select Enable to use the Alarm Notification. 2 SMTP server address: Used to send E-mail to the address on SMTP (Simple Mail Transfer 7 8
Protocol)Server. Enter the SMTP server address and your personal e-mail address (only the part after @). ex) smtp.samsung.com Authentication Login: Select the Enable to use the log-in screen. It is recommended to select the Enable. User ID: Enter the User ID of the sender s E-mail address when using the Authentication Login. Password: Enter the User Password of the sender s E-mail address when using the Authentication Login. Sender(E-mail): Enter the sender s E-mail address. E-mail address 1~4: Enter up to 4 mail addresses to receive capture images. Image Count: Set the number of images to be transmitted upon Alarm Notification. Pre Alarm means the number of images to be sent before the Alarm, and Post Alarm is the number of images to be sent after the Alarm. Up to 5 images can be sent in a 0.5-second interval. PIR is linked with Preset : Select Enable if you want to move the camera lens to the specified Preset 1 when an alarm occurs. - Network Configuration: Set the Static IP or the DHCP. - PPPoE(ADSL): Set the PPPoE(ADSL). - UPnP Configuration: Set the Port Forwarding and the Display shortcut Icon in My Network Places. - Network Ports: Set the HTTP Port. - View Network Status: Display the network status of the current system. - Network Status Notification: Send information on allocated IP addresses such as the DHCP and the PPPoE. - DDNS Configuration: Set the DDNS.
Network Configuration Set the Static IP or the network of the cable modem. Talk with the network administrator, and enter correct values for items. Static IP
PPPoE (ADSL) Set the ADSL network.

Save Configuration Store the settings in the memory of Netcam(W),and save them when power is turned off or the system is re-booted. - To store settings in the memory, click the Save Button.
Do not use this function Warning unless necessary. All the stored settings are switched to factory default. System Update You can update firmware in two ways. - Normal Update: Update to the latest version of software for improving performances.
Press the Reset Button on the back of the Netcam(W) for more than 5 seconds to return to default settings. Then, settings stored in memory are erased.
- All Update: Seldom used. It updates the system to repair a serious defect such as program bug.

Normal Update

1 Click the OK Button.
4 Click the Open Button after selecting a system file to update.
2 Click the Yes or NO Button.

5 Click the Next Button.

Click 3 Click the Search Button.
6 Click the Next Button. Click
7 Click the Search Button.
10 Click the Next Button.

Click Click

11 Click the Reboot Button. 8 Click the Open Button after selecting a Web file to update.

12 Click the OK Button.

9 Click the Next Button. Click
Note Connection with Netcam(W) is cut during rebooting.Close Internet Explorer, and access the Internet again after 1 minute. You can download the latest version of software from the Samsung Electronics Website (http://www.samsung.com). - You have to separate wired from wireless models before updating. File name of a wired model: system - l - *, web- l - * / File name of a wireless model: system - w - *, web- w - * - Do not update any file that you have changed its extension to a system or web format at your own. Otherwise it will cause a serious damage to the system. - Just click Skip if updating a system or web file is not necessary. 71
Access to Netcam(W) via a cell phone (USA Only)
You can view still images of Netcam(W) by accessing the Internet via a cell phone. Enter http: //Global_IP address (or domain name): port number/wap. htm on the URL page of the cell phone, and press the OK button. (ex) http://wfffbbb.websamsung.net:8080/wap.htm - Enter the user name and password when the authorization window appears, and press the OK button.

< View and Control Images >
DISPLAY MODE < Main Page >
- 160x120 - 320x240 - Help - You can view images without the authorization process when the Access Limitation Configuration of the Smart Viewer settings is set to Full Access. Warning - The authorization process does not appear again after an initial authorization if you store the ID/Password in the cache during mobile phone settings.

< Help Page >

Explains camera operations. - Button 1: Displays the main page. - Button 2/4/6/8: Controls the Pan/Tilt. - Button 5: Refreshes still images. - Button 7: Turns On/Off the flash. - Button 9: Turns On/off the PIR sensor.
- Communication service providers available are listed below (as of August, 2005). * Cingular * Sprint * T-Mobile - Connection to or control over SNC-L200(W)may not work, depending on the communication service provider, mobile phones model or firmware version, area and/or wireless network operator, or for other reasons.
Installing the MultiViewer Program
You must first install the multi program of the installation CE to use more than one Netcam(W).
- Computer: Pentium 4/2.0 GHz or higher (8 channels) Pentium 4/2.4GHz or higher (16 channels) - Operating System: Windows 2000/XP (Service Pack installation is recommended) - Ram Memory: 512MB or higher - Video Memory: 64MB or higher - Resolution: 1024 X 768 - Web Browse: Internet Explorer 6.0 or higher
1 Insert the Installation CE into the CD-ROM of the PC. 2 Double click the NetworkCarmeraMV__Setup. exe of the CD. 3 Click the Next Button. 4 Click the Install Button.

5 Install is process.

To cancel the installation, click the Abort Button.
6 Click the OK Button. Installation is completed, and the Move to icon appears on the Background Screen.
Registering the Netcam(W)
You can register up to Netcam(W) 16 units.
1 Double-click the Network Camera MultiViewer icon on the Background Screen. Or Click [Start ] -[All Programs ] [Network Camera MultiViewer ] [Network Camera MultiViewer ] to start. 2 Click the MultiViewer Set Button. 2
- The Registration Screen appears.
Deleting the Registered Netcam(W)
1 Select the Netcam(W) to be deleted from the registration list. 2 Click the Delete Button. 3 Click the Yes Button.
3 Click the New Button. 4 Enter information on the Netcam(W).
- Check the StartUp item, and video is automatically connected when the MultiViewer program starts.
Modifying the Registered Netcam(W)

Sequence View

Video of the connected Netcam(W) is displayed in sequence automatically. Click the Sequence View Button. - 1 Channel:Video is displayed by one channel in sequence. - 4 Channels:Four screens are displayed at the same time,and switched up to four pages in sequence. - 9 Channels:Nine screens are displayed at the same time,and switched up to two pages in sequence. - 16 Channels:No sequence view is enabled.
To clear the Sequence View,click one of the 1/4/9/16 Channel Buttons. Channels are displayed in the Setup-Sequence time interval,and one by one in sequence.

Recording Video

You can record video from each channel by using the MultiViewer.
1 Select video you want to record on the MultiViewer Screen. 2 Click the Record Button( ).
- The REC-F is displayed on the screen,and recording begins.
3 Repeat the step 1 and 2 to record another video.
- Record video for 10 minutes,creating a recorded file for each Netcam(W).

Stop Record

Press the Record Button(

- Stop recording.

Sequence View can be set in 5 to 30-second interval in MultiViewer Mode.
- Recorded files are stored in the C: WProgram FilesWNetwork Camera MultiviewerWVideo Files.
Recording is stopped when the free space on the HDD is less than 5GB. Check the free space on the HDD if its sufficient to record video continuously.
Record video for up to 10 minutes for each Netcam(W).

Recording Motion

Set the motion area in the 16-split video, and automatically record video when a motion is detected in the set area. This function is applied to only one channel.
6 Set the most appropriate value by repeating the step 3 to 5. 7 Click the Enable Motion Detection to display the motion detection.
- The motion detection is selected. - To clear the motion detection, click the button again and clear the display.
1 Click the video you want to motion-record on the MultiViewer Screen. 2 Click the Motion Button( - The Motion Record Screen

appears.

8 Click the OK Button.
- Settings are completed.
3 Click the Motion area in the 16-split screen.
- The motion area is displayed in green color.
When a motion is detected in the motion area
- Click the button again to clear the motion area.
The motion area turns red, and blinks. Recording starts automatically.
- The REC-A is displayed on the screen, and video is recorded for up to 10 minutes.
4 Enter the Sensitivity Value.
- Enter a value between 1 and 10.The level of sensitivity increases close to 10.
5 Click the Pretest Button.
- The Sensitivity Setting Value is temporarily stored. - When a motion is detected, the motion area turns red, and blinks.Testing starts.
The Motion Detection detects and records a motion, while the PIR detects infrared.

Capturing Video

You can capture the images you want as JPEG files anytime during monitoring.

Screen Display

You can display Information on the Netcam(W) on the MultiViewer Screen.
1 Click the video you want on the MultiViewer Screen. 2 Click the Capture Button(
- Video is captured as a JPEG file. - Captured files are stored in the C:WProgram FilesWNetwork Camera MultiviewerWVideo Files folder.
Click the Screen Display Button(
- To clear the screen display, click the Screen Display Button again.

Printing Video

You can capture the images you want in JPEG file anytime during monitoring.
Running the SNC Installer
You can open the Smart Viewer by running the SNC Installer during the MultiViewer.
- The print screen appears.
Click the SNC Installer Button( ).
- The SNC Installer is executed, and the Netcam(W) Search Screen appears. - Refer to Page 42 to open the Smart Viewer.

3 Click the Memo Button.

- Enter information on print, and click the OK Button.
4 Click the Setup Button.
- Click the OK Button after setting the printer. Printing starts
Playing Back the MultiViewer
MultiViewer Playback Screen
Small Screen View Button: Play back images in 160X120 resolution. Normal Screen View Button: Play back images in 320X240 resolution. Large Screen View Button: Play back images in 640X480 resolution. Viewer Screen View Button: Play back images in MultiViewer Screen size. Full Screen View Button: Play back images in full monitor screen. Press the Esc
Button to cancel the Full Screen View.
Open File Button: Open files to be played back. Snapshot Button: Capture playback images. Print Button: Print images. Event Log Button: Check all the information and status on the MultiViewer.
Reverse Playback Button: Reverse-play back video. Pause Button: Stop playback for seconds. Playback Button: Play back video. Stop Button: Stop playback. Search Button: Fast-search forward or backward. Previous Image Button: View the previous/next images cut by cut in Pause mode. Previous File Button: Move to the previous/next file.
Scroll Bar: Move the playback position by moving the scroll bar with a mouse. You can move to the image you want in Stop/Pause Mode.

Record File Playback

You can check event log information in the MultiViewer, as well as play back, capture and print recorded files.

Event Log Information

You can check events (Alarm, Motion, Disconnect, Reconnect etc.)based on the date and motion status of the Netcam(W) connected to the MultiViewer. Alarm and Motion events are attached with recorded files. You can check the recorded video. Play back the files by double clicking on the name of the file.
1 Click the Multi Playback Mode icon on the MultiViewer Screen.
- The Multi Playback screen appears.

Click the Open Button.

1 Click the Event Log Button ( ) in the MultiViewer Playback screen.
- The Log Screen appears.
3 Open the file to be played back, and click the Open Button.

- Playback begins.

2 Click the Open Log File Button.
- Log files appear based on date.
Select the log file you want, and click the Open Button.
- Information is displayed on the log screen. Stop Playback

Click the Stop Button

Files with the extension name of.fjp are moving images, and files with.jpg are capture files.

Setting the MultiViewer

Event Log Screen
Setting the Viewer Environment
1 Click the MultiViewer Set Button on the MultiViewer Screen.
- The Setup Screen appears.
Click the Viewer Setup Tab. 2
- The MultiViewer Set Screen appears.
Time: Display the data and time of creating the log file. Target: Display information on the Netcam(W) server. IP Address: Display the Netcam(W) IP address. Mac address: Display the Netcam(W) Mac address. (Displayed on the label on the top of the main body) Event Mode: Display log information based on status. Reconnected, Motion and Forced Alarm and Disconnected File Folder: Display the location where the recorded file is stored.
3 Click the Close Button when the settings are completed.
Setting the Scheduled Recording
You can record the Netcam(W) on the specific day and at the specific time you want.

Selecting Logo

You can change the company logo on the right side of the MultiViewer Screen.
1 Select the Netcam((W)to scheduled-record from the Schedule of the Image Recording. Click the Browser Button.
- The Scheduled Recording Screen appears.
1 Click the Browser Button of the Logo Image File. 2 Select the company logo file to be used, and click the Open Button.
- The company logo on the MultiViewer Screen changes.
3 Select the day of the week you want.
- When you click the Select All Button, the Netcam(W) is recorded everyday.
4 Select the time you want.
- Check on the Use Time Range, and set the time.
Only.bmp company logo files can be used.