FREEZER/REFRIGERATOR

Model : SRL3928B(A)/39WEB(A) SRL3926B(A)/39NEB(A) SRL3916B(A)/39NMB(A) SRL3626B(A)/36NEB(A) SRL3616B(A)/36NMB(A)
Eletrodomsticos Frum Todo sobre Electrodomsticos
www.eletrodomesticosforum.com

FREEZER / REFRIGERATOR

CONTENTS
1. Precautions.. 2 2. Product Specifications.. 3 3. Electrical part specifications & standards. 4 4. Setting Temperature of the Fridge/Freezer. 5 5. Circuit Diagram.. 6 6. Functions & Operating Instruction. 9 7. Functions of Refrigerator. 13 8. Circuit Descriptions.. 19 9. Diagnosis of disorder and method of repair. 24 10. Parts List.. 31 11. Disassembly & Assembly.. 39 12. PCB Circuit Diagram... 45

1. Precautions

Warning : Please abide by the following precautions in order to conduct the maintenance procedures in a safety fashion. Cleaning : After completing repairs, clean the surrounding area and the refrigerator and tell the consumer about the repairs being made. This appliance contains a small amount of the refrigerant isobutane(R600a), a natural gas with high environmental compatibility but which is also combustible. When transporting and installing the appliance, care should be taken to ensure that no parts of the refrigerating circuit are damaged. Refrigerant squirting out of the pipes could ignite or cause an eye injury. If damage occurs nevertheless, avoid any flames or potential sources of ignition, and air the room in which the appliance is standing for several minutes.
In order to avoid the creation of a flammable gas-air mixture if a leak in the refrigerating circuit occurs, the size of the room in which the appliance may be sited depends upon the amount of refrigerant used. The room must be 1m3 in size for every 8 g of refrigerant R600a inside the appliance. The amount of refrigerant contained in your particular appliance is shown on the identification plate inside the appliance. Never start up an appliance showing any signs damage. If in doubt, consult your dealer.
1-1. Caution when you replacing compressor.
Do not smoke. Remove all the possible ignition sources and then replace compressor in wellaired places. Dont use welding machines if R600a refrigerant does not exposed. In the case of gas leakage, always open the windows. When cutting the SUCTION, DISCHARGE pipe of the compressor, always take caution of the inner pressure of the remaining gas.
1-2. Take out the power plug
Always take out the power plug from the outlet when doing repairs.
1-3. Be careful of electric shocks
When inspecting the circuit, dont touch the battery charger and be careful of electric shocks.
1-4. Use proper components
Always use the component labeled in the service component chart when replacing components for repairs.
Refers to prohibition. Refers to prohibition of dismantling. Refers to prohibition of contact. Refers to guidelines which have to be followed. Refers to detaching the power plug from the outlet. Refers to earth connection for preventing electric shocks.

1-5. Use proper tools

Always use proper tools for repairs. If worn out tools are used, it would cause defects in tuning and electrical contact, leading to accidents.
1-6. When doing repairs, inspect the POWER 1-7. Cutting of LEAD-WIRE
CORD or whether there is fire in the lead wire and make sure they are replaced.
For connecting the lead-wire that has been cut off, use soldering or connector and always disconnect the vinyl tapes.
1-8. Check for disconnection
After completing the assembly, always measure the disconnection resistance level, and turn on the power after checking it is above 1M.

1-9. Earth

Check the status of earthing and repair the incomplete ones.
Refers to possibility of death or serious injury of a person.

Warning

Refers to possibility of injury of a person or damage to property.
1-10. Be careful of children
There is always the possibility of danger when doing repairs so make sure that children cant come nearby. Samsung Electronics

Caution

2. Product Specifications
Model Capacity (ISO) Dimension Net (Liter) Width(mm) Depth(mm) Height(mm) Net weight (kg) Cooling technology Freezer performance Control&Display Temperature control type Temperature display type Power off Super Freezer Function VAC ECO Alarming display for power failure Alarming melody for door open REFRIGERATOR COMPARTMENT Water dispenser(4.2L/Child lock) Shelf Tempered glass shelf Optional Optional 2 Optional Optional Optional Optional 1EA 1EA 1EA Optional Optional Optional Optional 2 Optional Optional Optional Optional 1EA 1EA 1EA Optional Optional Optional Optional 1EA 1EA 1EA Optional Optional Optional Optional 2 Transparent plastic Vegetable/Salad bin(Moisture controller) Interior lamp Door storage Incandescent lamp Fluorescent lamp Can-carry Door pocket Transparent/White Dairy pocket Deep bottle storage Egg tray FREEZER COMPARTMENT Drawer Ice tray Blowing agent Refrigerant Transparent / White Twist / Normal tray(2EA) Recessed type Bar type Total Freezer Refrigerator SR-L3928B(A) SR-L39WEB(A) No-frost (4-STAR) Electronic Digital
SR-L3926B(A) SR-L39NEB(A) SR-L3626B(A) SR-L36NEB(A) SR-L3916B(A) SR-L39NMB(A) SR-L3616B(A) SR-L36NMB(A)
350/325 104/104 246/1920/1820 76/73 No-frost (4-STAR) Electronic Digital
350/325 104/104 246/1920/1820 76/73 No-frost (4-STAR) Semi electronic LED
Cyclo Pentane Cyclo Pentane Cyclo Pentane R600a(65g) / R134a(155g)

Samsung Electronics

3. Electrical part specification & standard
ITEM Model Power source Refrigeration cycle Model Compressor starting type STANDARDS SR-L3928B(A)/L39WEB(A), SR-L3926B(A)/L39NMB(A) SR-L3916B(A)/L39NMB(A), SR-L3626B(A)/L36NEB(A) SR-L3616B(A)/L36NMB(A) 230-240V/50Hz DK4A1Q-L1U (R600a) 230V/50Hz 220V/50Hz 127V/60Hz DK172Q-L2U DK172P-L2U (R134a) (R134a) R.S.C.R FREOL 15c/265cc Split fin.Tube Type Natural Convection Type Molecular Sieve XH-9 I.D 0.75 L4,000mm 502AT 502AT 502AT 502AT 310W/240V 2W/240V 7W/240V 15W/240V 7W/240V 310W/220V 2W/220V For Only Fluorescent Lamp 7W/220V 15W/220V 7W/220V 250V/10A, 6 19hr(Vary According To The Environmental Conditions) 4hr 10min(At The First Operating Cycle) 7min 2min 350VAC/3.5 4TM213PHBYY-350VAC/5 4TM232SHBYY-135 J531Q35E330M385-2 20% 10 250VAC/12 4TM435PHBYY -125 J531Q33E100M200-2 20% 310W/127V 2W/127V 7W/127V 15W/127V 7W/127V

6-4. Cool Air Circulation
7. Functions of Refrigerator
7-1. 7-Segments Display Function

Section Function

Initial POWER Notch setting Blink setting temperature of freezer until temperature reaches below (YES) TFSET_ON +3 ON (Power s/w, instantaneous Notch setting -- displayed (until the notch control is operated) electricity failure) (NO) Stabilization of the temperature in the freezer (Since the setting temperature have reached) Blink if temperature goes above TFSET_ON +3. Display the setting temperature if the temperature goes below TFSET_ON +2
Display Blinking continuously ignoring temperature of freezer if displayed state of freezer before defrosting was Blinking. Display Setting temperature of freezer continuously ignoring temperature of Defrosting (precooling+defrosting+pause) freezer if displayed state of freezer before defrosting was Setting temperature of freezer. Maintain temperature constantly while it reaches TFSET_OFF point When you return to the operating cycle. Super Forced freezing Forced defrosting Display function of the temperature of refrigerator Blink if temperature goes above TFSET_ON +3 Display the setting temperature if the temperature goes below TFSET_ON +2 Display Display (Forced Freezing) (Forced Defrosting)
If you push REF. TEMP. button indicative LAMP of refrigerator starts to light up and blink the setting temperature of refrigerator. If you do not input the KEY, it is blinked 5 times for 5 seconds at 0.5second interval and automatically converted to the displayed state of setting temperature of refrigerator. If you push FRE. TEMP. button indicative LAMP of freezer starts to light up and blink the setting temperature of freezer. If you do not input the KEY, it is blinked 5 times for 5 seconds at 0.5second interval and automatically converted to the displayed state of setting temperature of freezer.
Display function of the temperature of freezer
References 1) TFSET-ON : Setting temperature of freezer +3 2) TFSET-OFF : Setting temperature of freezer -3
7-2. Function of Thermostatic Control

A. Function of controlling the temperature of freezer
1) You can control the temperature of freezer from -17
to -25 at 1 interval by pushing the control button of the temperature of freezer.(FRE. TEMP.) 2) Temperature is displayed in following order -19 -20 -21 -22 -23 -24 -25 -17 -18 whenever you push the control button of temperature. 3) The temperature of freezer is automatically set to be -19 on initial POWER ON. Section 7 Segment Controlled temperature of freezer 13 Power 1 time push 2 time push 3 time push 4 time push 5 time push 6 time push 7 time push 8 time push 9 time push 19C 19C 20C 20C 21C 21C 22C 22C 23C 23C 24C 24C 25C 25C 17C 17C 18C 18C
B. Function of controlling the temperature of refrigerator
1) You can control the temperature of refrigerator from 6
to 1 at 1 interval by pushing the control button of the temperature of refrigerator. 2) Temperature is displayed in following order whenever you push the control button of temperature. 3) The temperature of refrigerator is automatically set to be 4 on initial POWER ON. Section 7 Segment Controlled temperature of freezer power on 1 time push 4C 4C 2 time push 3C 3C 3 time push 2C 2C 4 time push 1C 1C 5 time push 6C 6C 6 time push 5C 5C note

C. SUPER Function

1) Press SUPER button briefly so that the LED lights up. The Freezer temperature will decrease and
the appliance will switch to the lowest temperature. 2) The displayed state is circulated in following order, SUPER is selected SUPER is selected, whenever you push the SUPER button one time. Section Dispaly change Initial power on SUPER Lamp off 1 time push SUPER Lamp ON 2 time push SUPER Lamp off SUPER is released note
3) If you select the ECO function while SUPER function is working, SUPER function is released and ECO

function begins to work.

4) If you select SUPER function, Compressor(and Fan) will be operating continuosly until the
temperature of freezer reaches -25. (10 seconds after selection) after working for 2 hours, compressor will be turned off automatically for 25minutes, and then compressor will be turned on antomatically until the temperature of freezer reaches -25 and this function will repeat for 8 hours. 6) If the commencing condition of defrosting is reached during super function, a defrosting cycle will be postponed until the next 25minutes delay time.
5) If the temperature does not reach -25

D. ECO Function

1) You can select or release this function by pushing the ECO button. 2) If you select the SUPER function while ECO function is working, ECO function will be released

and SUPER function will begin to work.
3) If you select the function of controlling the temperature of freezer compartment or fresh food
compartment while ECO function is working, ECO function will be released.
4) If you select the ECO function, the temperature of freezer and refrigerator will be controlled as -17

and 6 , respectively.

E. VACATION Function
1) You can select or release this function by pushing the VAC button. 2) If you select the VAC function, the temperature of refrigerator will not be controlled and DAMPER
will be maintained as closed state. So that, cool air will not be supplied to the refrigerator.
3) VAC function does not affect setting up of the temperature of freezer. 4) If you push the button of controlling the temperature of refrigerator while VAC function is working,
VAC function will be released automatically. Samsung Electronics 14

7-3. Initial Function

A. Initial function of first POWER ON
1) If power is pressed (POWER S/W ON), it will begin to make a self diagnosis and light all
DISPLAY for 2 seconds if normal condition is confirmed
2) After lighting DISPLAY ON, 7-Segment will be displayed as --. 3) Defrosting HEATER is set to be ON forcibly for 3 seconds irrespective of the evaporator
temperature. 4) After turning the defrosting HEATER ON for 3 seconds, turn off the defrosting HEATER and turn COMP. ON and keep it up for 5 minute irrespective of temperature of refrigerator. 5) After turning COMP. ON, operate DAMPER-MOTOR for control of refrigerator and confirm the zero point and 60Hz/50Hz and then control as considering the temperature condition of refrigerator. 6) At this moment, if it does not confirm the zero point due to the disorder of the some part of DAMPER-MOTOR, COMP. will be stoped immediately and display self diagnosis.

7-4. Defrosting Function

A. Common function
1) The period of defrosting is set to be 19 hours according to the COMP intergrated criterion.
Previous standard means the following conditions : frequency of opening and closing of the DOOR of refrigerator must be less than one time, the temperature of refrigerator and the temperature of freezer did not increase above TRSET ON+6 and TFSET ON+4 , respectively and special functional button (VAC,SUPER,ECO)was not selected. Besides the predescribed condition, the period of defrosting will be 6 hours and 50 minutes unconditionally. 2) If power is turned off and then is turned on again, the commencement of defrosting will be after 4 hours of the running time of compressor. 3) The COMP and FAN during defrosting, will stop and DAMPER-MOTOR will swing continuously. 4) At a pause time, DAMPER-MOTOR. 5) With the exception of 19 hours in the period of defrosting, will also swing the Pre_Cooling will be executed by operating the COMP forcibly for 50 minutes before execution of defrosting. 6) You are recommended to have a pause time after completion of HEATING. 7) The HEATING for defrosting will be controlled by SENSOR. If SENSOR is out of order or the temperature of EVAP is higher than HEATER ON temperature, HEATING will be skipped and ref only has a pause time.

C. TEST release function

1) If you push REF. TEMP. and FRE. TEMP. button simultaneously for 5 seconds only once during the
forced defrosting, the forced TEST function will be converted immediately to the previous temperature setting state immediately and will disappear on the DISPLAY.
7-6. The compensating function for electricity failure

A. NOTCH SAVE function

1) Whenever you push one of the SUPER, ECO, VAC, FRE.TEMP. and REF.TEMP. Button, the
current state will be saved and set to be the NOTCH and DISPLAY state which value was memorized as the one at rebooting point of POWER, respectively. 2) If the evaporator temperature at the inititial POWER ON state is less than the general defrosting OFF temperature, a clause1) will begin to work. If the evaporator temperature at the inititial POWER ON state is above the defrosting OFF temperature, the NOTCH of FRE.TEMP. and REF.TEMP. will be set to be -19 and 4 , and SUPER, ECO and VAC function does not selected.
7-7. The rest control functions
A. Function of COMP protection
1) After COMP is turned off, 5 minutes must be elapsed for the another operation under all conditions. 2) For the forced operation, compressor will begin to work immediately by pushing the forced operating
function without any delay for 5 minutes.
3) At the initial moment of POWER ON or POWER S/W ON, this function begins to work immediately
after heating of defrosting for 3 seconds.
B. Function of supercooling protection of refrigerator with a surrounding air of low temperature.
1) If the temperature of surrounding air begins to drop below 13 , the hysteresis of freezer sensor will
alter 3.0 into 1.5 and the temperature of refrigerator will be controlled with -1 shifted. 2) If the temperature of surrounding air will be between 14 and 31 , the hysteresis of freezer sensor will be back to 3.0 and the refrigerator will be controlled with REF. TEMP. setting temperature. 3) If the temperature of surrounding air begins to rise above 33 , the hysteresis of freezer sensor will alter 3.0 into 1.5.
C. Function of NOTCH compensation
1) The NOTCH of refrigerator temperature will be -1
shifted when the NOTCH setting of freezer and refrigerator are ranged from -17 to -19 and 1 to 2 , respectively. 2) The NOTCH of refrigerator temperature will be +2 shifted when the NOTCH setting of freezer and refrigerator are ranged from -25 to -23 and 5 to 6 , respectively. 3) The NOTCH of refrigerator temperature will be set to be normal condition when the NOTCH setting of freezer is ranged from -20 to -22.
7-8. Function of Self diagnosis

A. Function of self diagnosis
to +50. It is treated as SHORT/OPEN if the MICOM input voltage is out of voltage range from 0.5 VOLT to 4.5 VOLT. The disorder table prepared by self-diagnosis NO Items R-SENSOR F-EVAP SENSOR F-SENSOR DAMPER-MOTOR (GEARED) CONTROL RELAY of DAMPERMOTOR disorder or MOTOR, REED S/W, MAGNET disorder cannot sensing ON/OFF of REED S/W for more than 1 minute operation Segments display Contents of disorder OPEN disorder SHORT disorder Note if sensing below -50 if sensing above +50
1) The criterion of disorder of temperature sensor is out of temperature range from -50
B. Function of initial self diagnosis by POWER ON
1) After POWER ON, inside of MICOM automatically detects the existence of the disorder of temperature sensor within one second. 2) If bad sensor is found out by self diagnosis, it will be displayed rotatory on the 7 Segment at 0.5 second interval. 3) If bad sensor is detected, any button will not be recognized and all electrical load will be set to be OFF and normal control of temperature will be reserved. 4) If bad part is repaired, it will be restored to the original state. 17 Samsung Electronics
C. Function of self diagnosis during normal operation
1) If you push SUPER and VAC button simultaneously for 5 seconds while the refrigerator is working, on the 7 SEGMENTS will be displayed and function of self diagnosis will be selected. 2) KEY input will not work while self diagnosis function is operating. (except for POWER button)
7-9. Function of DOOR OPEN WARNING and control the light in refrigerator.

A. Warning of DOOR OPEN

1) BUZZER WARNING(ding-dong) SOUND will be generated if 2 minutes are elapsed continuously with the refrigerator door open. 2) Initial BUZZER WARNING will be generated for 10 seconds after 2 minutes of DOOR OPEN, and since then Ding-Dong sound will be generated every one minute for 10 seconds periodically. 3) If the refrigerator door is closed, warning will stop immediately. 4) If 10 minutes are elapsed continuously with the door open, light in refrigerator will be turned off and warning continues to work.
B. Function of controlling the light in refrigerator
1) If 10 minutes are elapsed continuously with refrigerator door open, the light in the refrigerator will be turned off automatically. 2) Despite of turning the light in the refrigerator off, it will be set to be ON again if you open the DOOR which was closed. 3) At this moment, OFF time of the light will be set to be 10 minutes again.
7-10. Function of POWER ON/OFF & Alarm of electricity failure
A. Function of POWER ON/OFF
1) This function is selected or released by POWER button. 2) If the power switch is turned on, all electrical load work normally, -- will be displayed on the 7-SEGMENTS DISPLAY. 3) At above state, 7-SEGMENTS will display the setting temperature if you push the freezer or the refrigerator setting BUTTON.

8-3. Division of RESONATOR
The role of this circuit is generation of synchronous CLOCK for transmission/reception of informations of the logical elements inside MICOM and the basic time for the calculation of time. Rated parts must be used in the division of RESONATOR because the calculation time of MICOM is changed or cannot work if specification is changed.

8-4. Division of SENSOR

SENSOR and F-rated resistance are connected to the GROUND and DC 5V, respectively. The resistance value which is changed by the temperature is converted to the voltage, and then respective temperature is discriminated by input voltage to A/D PORT of MICOM
8-5. Division of OPERATING
If at MICOM PORT begins to output High signal which corresponds to electrical load which we intend to work, DRIVER IC(KA2657) is turned ON and at this moment, corresponding electrical load starts to operate because the DC12 yield the electric current which flows corresponding RELAY COIL and RELAY contacting point is set to be ON so corresponding electrical load begins to operate.

8-6. Division of BUZZER

TRANSISTOR begins to operate by CLOCK which was generated at MICOM and BUZZER sound is generated by impression of 12V to the BUZZER.
8-7. Division of DISPLAY, KEY SCAN
from MICOM #3-#7 GHID signal is generated for 10 sec with the period of 2 sec HIGH signal and for the lighting the corresponding LED, the CONTROL terminal of MICOM PIN #8-#11 output the output signal which is coincident with GRID signal. Meanwhile by pushing the KEY which is connected by respective GRID, corresponding signal is inputted to MICOM.

8-8. Division of OPTION

The output such as GRID wave form which is only generated at the initial POWER ON is accepted as input through SWITCHING DIODE and discriminate OPTION by matrix method. #23, #24, and #25 PORT of MICOM PORT generate the same output with GRID wave form only at initial POWER ON.
Shift of temperature in freezer compartment(unit : C) SHIFT Default -1.0C -2.0C -3.0C +1.0C +2.0C +3.0C +4.0C 1
Shift of temperature in refrigerator compartment(unit : C) SHIFT Default -1.0C -2.0C -3.0C +1.0C +2.0C +3.0C +4.0C 1
9. Diagnosis of disorder and method of repair
Method of inspecting MAIN-PCB At the self diagnosis CHECK, you have to turn the main power OFF and turn it ON and check. ERROR CODE of self diagnosis is prepared as shown in the following table. ERROR CODE of self diagnosis NO Items R-SENSOR F-EVAP SENSOR F-SENSOR DAMPER-MOTOR (GEARED) CONTROL RELAY of DAMPERMOTOR disorder or MOTOR, REED S/W, MAGNET disorder cannot sensing ON/OFF of REED S/W for more than 1 minute operation Segments display Contents of disorder OPEN disorder SHORT disorder Note if sensing below -50 if sensing above +50
Door s/w R-sensor Refrigerator compartment

A. When Ding-Dong sound is generated continuously.
B. When the beeper sound is generated continuously
C. When the KEY of PANEL-PCB has not been selected.

10. Parts List

10-1. Freezer Compartment

Freezer List

1 1-1 1-2 1-3 1-5 5-1 5-6-1 6-2 6-3 6-4 6-7-1 7-2 7-3 7-8-9-1 9-2 9-3 9-4 9-5 9-6

CODE-NO

DA66-00087A DA71-00108A DA66-00071A DA64-00158A DA61-20136A DA66-00086A DA66-00091A DA66-00091B DA66-00092A DA66-00092B DA66-00101A DA66-00056A DA67-00302A DA61-00137A DA61-00082A DA66-00052A DA66-00053A 6002-000215 6002-000213 DA96-00015A DA96-00015B DA96-00024A DA32-10105Q DA47-10162F DA60-00053A DA60-00054A DA63-00395E DA63-00395F 6002-000215 DA63-00396R DA63-00396S DA97-00150A DA63-00237A DA61-00081A DA63-40119A DA31-00002P DA31-00002U DA31-00002X DA61-00117A DA31-10107C DA31-10107B DA31-00019A DA34-10125B 6002-000467 DA31-00026A DA63-00359A DA66-00095A DA61-20128A 6002-000215 DA32-10109P 6006-001083 DA47-00056A DA47-00056B DA47-00056C 6002-000215 DA66-00052A DA66-00053A DA67-40146B
TRAY ICE-ASSY FIXER-TRAY ICE TRAY-ICE KNOB-TRAY ICE SPRING-ICE MAKER TRAY FRE-C-ASSY TRAY FRE-A-ASSY TRAY FRE-A-ASSY TRAY FRE-B-ASSY TRAY FRE-B-ASSY TRAY-ICE,CUBE, ASSY TRAY-ICE,CUBE CAP-TRAY-ICE,CLUB SUPPORT-RAIL ASSY SUPT-RAIL ROLLER-FRE-A ROLLER-FRE-B SCREW-TAPPING SCREW-TAPPING EVAP ASSY EVAP ASSY EVAP ASSY SENSOR ASSY THERMO FUSE SPACER-EVAP,L SPACER-EVAP,I COVER-EVAP FRONT-ASSY COVER-EVAP FRONT-ASSY SCREW-TAPPING COVER EVAP REAR-ASSY COVER EVAP REAR-ASSY COVER EVAP REAR-ASSY COVER-EVAP REAR CASE-MOTOR GROMMET-MOTOR MOTOR-FAN MOTOR-FAN MOTOR-FAN CASE-G-MOTOR MOTOR-GEARD MOTOR-GEARD FAN-PROPELLER SWITCH SENSITIVE SCREW BLADE GASKET-BLADE SHAFT-BLADE ASSY SPRING-FAN SCREW-TAPPING SENSOR-ASSY SCREW ASSY TAPP HEATER-EVAP COVER,RE HEATER-EVAP COVER,RE HEATER-EVAP COVER,RE SCREW-TAPPING ROLLER-FRE-A ROLLER-FRE-B TRAY ICE

SPECIFICATION

HIPS,SRL36,L39 HIPS,W9540,SRL36,L39 SRL36,L39,W9540 HIPS,W9540,SRL36,L39 STS304,ID1.0,PI10.5,SR-53E SRL36,L39 WHT TRANSE PARENT WHT TRANSE PARENT SRL36,L39 SRL36,L39 HIPS,WHT,SRL36,L39 HIPS,SRL36,L39,WHT POM,SRL36,L39 POM,SRL36,L39 TH-1S,M4XL16,ZPC(YEL),MSWR1 TH,M4,L12,ZPC(YEL),SWRCH18 SRL36,L39,FIN,A1100P-H24,240V,310W SRL36,L39,FIN,A1100P-H24,220V,310W SRL36,L39,FIN,A1100P-H24,127V,310W 502AT,COMBI-PJT,300,YELLOW,F-DEF-SENSOR 250V,10A,72 127V EVAP ASSY 127V EVAP ASSY TWIST,PP NORMAL,PP TH,1,M4.0,L16,ZPC(YEL),MSWR1 240V/50Hz 220v/50,60Hz 127V/60Hz PP,NTR,SRL36,L39,T1.5 PP,SRL36,L39,NTR NBR,BLK 240V/50Hz, 2550 rpm 220V/50Hz, 2550 rpm 127V/60Hz, 2550 rpm PP,SRL36,L39,NTR M2LA49Z,220V,SR-41~518 M2BC59ZR12,110V SRL36,L39,NTR 5V,Black PH-2S 4X10 YEL PC,NTR,SRL36,L39 SILICON POM,SRL36,L39 STS27,ID1.0 TH,1,M4.0,L16,ZPC(YEL),MSWR1 502AT TH,M4,L16,ZPC(YEL),SWRCH18 240V 220V 127V TH,1,M4.0,L16,ZPC(YEL),MSWR1 POM POM PE, NTR, SR-1500

REMARK

9-7 9-8 9-9 9-10 9-11 9-12 9-13 9-14 9-15 9-16 9-13
10-2. Refrigerator Compartment

Refrigerator List

1 1-1 1-2-1 2-2 2-3 2-3-1 3-2 3-4-1 4-2 4-5-1 5-2 5-6-1
DA61-00126B DA69-00102B DA67-00203A DA67-00272A DA64-00119A DA66-00061A DA67-20346K DA64-00116A DA67-00268A DA64-00114A DA64-00115A DA67-20346J DA67-00270A DA64-00115A DA64-00116A DA67-20346J DA67-00269A DA64-00114A DA64-00116A DA67-20346H 4713-001041 4713-001140 4713-001141 DA63-00235A 6002-000213 DA97-00228A DA63-00239B DA72-00170A DA67-30266D 6002-000215 DA63-10467A DA32-10105B DA63-00234A DA63-00870A DA63-00245B DA64-00118A DA64-00117A DA63-00371A DA63-00390A DA70-00138A DA41-00014A DA41-00018B DA41-00013A DA41-20160B DA39-00112A 6002-000213 DA34-00015C 6001-000366 DA97-00526A DA63-00328B DA64-00180B DA64-00180A DA63-00375A DA63-00375A DA70-00208A DA41-00043A DA41-00042A DA67-00329A DA67-00444A DA67-00206A DA67-00207A
BOX-VEG ASS,Y BOX-VEG CAP-VEG SHELF-VEG ASSY TRIM-SHELF-FRONT, LOW LEVER-HUMIDITY SHELF GALSS TRIM-SHELF REAR-A SHELF REF-B-ASSY TRIM-SHELF REF-FRONT TRIM-SHELF REAR-B SHELF GALSS SHELF REF-C-ASSY TRIM-SHELF REAR-B TRIM-SHELF REAR-A SHELF GALSS SHELF REF-A-ASSY TRIM-SHELF REF-FRONT TRIM-SHELF REAR-A SHELF GALSS LAMP-FLUORESCENT LAMP-INCANDESENT LAMP-INCANDESENT COVER-LAMP REF SCREW-TAPPING COVER DAMPER-REF ASSY COVER-DAMPER REF SPACER-DAMPER, REF CAP-SCREW SCREW-TAPPING COVER-SENSOR SENSOR-ASSY COVER-SUCTION, REF COVER-TOP TABEL ASSY COVER-TOP TABLE ASSY BUTTON-PCB, R BUTTON-PCB, L GASKET-BUTTON PCB,R GASKET-BUTTON PCB,L PLATE-EARTH PBA-PANEL PBA-MAIN PBA-SUB PBA-SUB WIRE HARNESS-INVERTER SCREW-TAPPING SWITCH-DOOR SCREW-MACHING COVER TOP TABLE,ASSY COVER TOP TABLE BUTTON PCB,R BUTTON PCB,L GASKET-BUTTON PCB,R GASKET-BUTTON PCB,L PLATE-EARTH PAN-PCB MAIN-PCB COVER DISPLAY GASKET-WINDOW SHELF-REF LOW SHELF-REF
GPPS HIPS GLESS PP,W9540 PP,WHT GLASS,T4 P.P,BJ-730T4 GLASS,,T4 P.P,BJ-730T4 PP,W9540 GLASS,T4 GLESS P.P,W9540 P.P,BJ-730T4 GLASS,T4 GLESS P.P,BJ-730T4 P.P,BJ-730T4 GLASS,T4 220V,150mA,11W 240V,25W 130V,25W PP TH-1S,M4X12,ZPC(YEL) PP,W-9540 PP,W-9540 PS PP TH-1S,M4X12,ZPC(YEL) HIPS 502AT PP,W9540 HIPS,SC-97527R ABS,SC-97527R,IN HOUSE ABS,SC-97527R ABS,SC-97527R MBR MBR SBHG1 COMBI COMBI 240V 127V INVERTER TH-1S,M4X12,ZPC(YEL) H3005CL,250V,25W FH,M4X10,CR PLT,STS304 SEMI ABS ABS,SC-97527R ABS,SC-97527R NBR,BLACK NBR,BLACK COMBI COMBI COMBI GPPS NBR GPPS(HF-2660),NTR GPPS(HF-2660),NTR,SRL36,L39
9 9-1 9-15 15-1 15-2 15-3 15-4 15-5 15-6 15-7 15-8 15-9 15-10 15-11 15-17 17-1 17-2 17-3 17-4 17-5 17-6 17-7 17-8 17-9 17-19

10-3. Door

Door List
DA91-00711A DA91-00711B DA91-00694A DA91-00694C DA91-00697A DA91-00694B DA91-00694D DA91-00697B DA91-00699A DA91-00699B DA91-00699C DA91-00701A DA91-00701B DA63-00228A DA63-00228B DA71-00118A DA63-00227A DA63-00227B DA63-00405A DA63-00405B DA63-00229A DA63-00229B DA63-00230A DA63-00263A DA63-00263B DA71-00119A DA66-00058A DA63-00380A DA64-00157A DA67-00216A 6001-000715 DA67-00298A DA61-00083A DA66-00073D DA63-00247A DA74-00054A DA67-30216A DA63-00240A DA65-20004A DA74-00051A DA61-00139A DA67-00194A DA66-00054A DA66-00055A DA63-00376A DA71-20155B

ASSY DOOR FOAM REF, DISP ASSY DOOR FOAM REF, DISP ASSY DOOR FOAM REF ASSY DOOR FOAM REF ASSY DOOR FOAM REF ASSY DOOR FOAM REF ASSY DOOR FOAM REF ASSY DOOR FOAM REF ASSY DOOR FIANM FEF ASSY DOOR FIANM FEF ASSY DOOR FIANM FEF ASSY DOOR FIANM FEF ASSY DOOR FIANM FEF GUARD-BOTTLE GUARD-BOTTLE GUARD-BOTTLE GUARD-VARIETY GUARD-VARIETY GUARD-DAIRY ASSY GUARD-DAIRY ASSY GUARD-DAIRY GUARD-DAIRY COVER-DAIRY GUARD-BOTTLE-DISP GUARD-BOTTLE-DISP GUARD-BOTTLE-B TRAY-EGG GUARD-CAN CARRY HANDLE BAR(FAT) CAP-HANDLE SCREW-MACHINE CAP HOLE HANDLE BAR HINGE-WASHER,LOW SHAFT-WASHER,D GROMMET-HINGE TANK WATER-ASSY CAP-COVER WATER COVER-WATER TANK CLAMP-TANK TANK WATER CASE-COCK ASSY CAP-HINGE HOLE TRAY-DISPENSER-A TRAY-DISPENSER-B COVER DISPENSER-ASSY FIXER-CASE,ASSY
SRL39, RICH-ROUND, COOLNCOOL SRL39, RICH-ROUND, COOLTECH DY SRL39, RICH-ROUND, COOL N COOL SRL39, RICH-ROUND, COOLATRVH DY SRL39, RICH-ROUND, BAR-HANDLZ SRL39, RICH-ROUND, COOOOLATRVH DY SRL39, RICH-ROUND, COOLTECH DY SRL39, RICH-ROUND, BAR-HAUDLZ SRL36,39, RICH-ROUND, RECZSS SRL36,39, RICH-ROUND, RECZSS SRL36,39, RICH-ROUND, RECZSS SRL36,39, RICH-ROUND, BAR-HANDLZ SRL36,39, RICH-ROUND, BAR-HANDLZ GPPS(HF-2660),SD-97527R,SRL36,L39,WHT GPPS(HF-2660),TRANSPARENT MSWR10,SNC2,SRL36,L39,PI5.5 REF,GPPS,SC-97527R,SRL36,L39,WHT REF,GPPS,TRANSPARENT REF,GPPS,SC-97527R,SRL36,L39,WHT REF,GPPS,TRANSPARENT REF,GPPS,SC-97527R,SRL36,L39,WHT REF,GPPS,TRANSPARENT GPPS,SRL36,L39 GPPS,W9540,SRL39,WHT GPPS,TRANSPARENT MSWR10,SNC2,SRL39(D),PI5.5 SRL36,L39,S.S ABS(HG-0760) ABS(HG-0760S),W-97527R,SRL39 ABS(HG-0760),W-97527R,SRL39 TH,+,M5 L16,SWRCH18A ABS(HG-0760S),WHT(SC-97527R) POM(TP-20),NTR T2.0,RD-PVC,N.T.R,SRL36,L39 NY-66,NTR,SRL36,L39,S.S PP,SRL39 PE,WHT PP,SRL39,S.S P.C PP,SRL39 ABS,SC-97527R,SRL39,DISP PP,SC-97527R,WHT ABS(HG-0760H),SRL39,W-97527,S.S,WHT ABS(HG-0760H),SRL39,W-97527,S.S,WHT SRL39 ABS,SR-L5285,L5785,SC-9343
3 3-5 5-1 5-6-9-1 9-2 9-13 13-1 13-2 13-3 13-4 13-17 18
10-4. Cabinet Parts & Unit
Cabinet Parts & Unit Lists

NO CODE-NO ITEM

ASSY CABI FOAM HINGE-UPPER-L HINGE-UPPER ASSY-R SCREW-TAP TITE CAP-HINGE HOLE-UPP CAP-SCREW SCREW-TAP,PH CAP-HINGE HOLE-MID SCREW-TAP TITE HINGE MID ASSY HINGE-LOW-L-ASSY HINGE-LOW,R-ASSY FOOT-FRONT CAP-HINGE HOLE-LOW SCREW-TAP TITE COVER-LEG,FR TRANS DC TRANS DC CHASSIS-COMP ASSY CHASSIS-COMP CASTER-FRONT RIVET CASE-JUNCTION COVER COMP-ASSY POWER-CODE C-OIL C-OIL C-OIL SCREW-TAPPING RELAY-PTC RELAY-PTC PROTECTOR-O/L PROTECTOR-O/L TRAY-DRAIN WATER DRYER-ASSY GROMMET-COMP COMPRESSOR COMPRESSOR COMPRESSOR COVER-RELAY SCREW-TAPPING BOLT-HEX SCREW-ASSY SCREW-TAP TITE SCREW-EARTH

Remove 3 screws

7. Remove the latch of the cooling cycle unit cover from the bottom.
s Assembly of the cooling cycle unit in the freezer
11-4. Assembly of mechanic compartment in the refrigerator
1. Remove the screws from the securing cover of the mechanic compartment at the back bottom.
2. Mechanic compartment assembly
11-5. Electric box assembly
Warning Make sure the power plug is taken out when replacing the components for the main PCB. 1. Disconnect the power cord.
2. Remove the cover of electrical box with insert driver.( )
3. Assembly specification of electric box

TEST S/W Condenser

D/C Trans
11-6. Disassembly of Top Table
q With the door open, unscrew screws with a screw driver(+ type). q Lever out top table with a screw driver (_ type).
q Repair or change electric parts of top table.
q Attach the top table and click into hook by pressing.

12. PCB Circuit Diagram

12-1. ELECTRONIC MODEL
12-2. SEMI ELECTRONIC MODEL

12-3. Service Parts

NO CODE-NO DA41-00018A 1 DA41-00042A DA41-00042C DA41-00014A 2 DA41-00043A 7 DA32-10105B DA32-10109P DA32-10105Q DA26-00003A DA41-00013A PANEL PCB(SEMI) R-SENSOR F-SENSOR F DEF-SENSOR DC-TRANS SUB PCB COMBI-P/J 502AT 502AT 502AT COMBI-P/J COMBI-P/J Seoul Semiconductor Dong Kwang Dong Kwang Dong Kwang Sigma Telecom YuYu INVERTER PCB ITEM MAIN PCB MAIN PCB(SEMI) STANDARD COMBI-P/J COMBI-P/J COMPANY Kwangju Electronics Kwangju Electronics Kwangju Electronics Seoul Semiconductor Qty Remarks
MAIN PCB(SEMI(AH/AM)) COMBI-P/J PANEL PCB COMBI-P/J
12-4. The Changed Part Lists As Supplying Voltages

240V/50Hz NO

230V/50Hz CODE-NO

DA02-40030A

220V/50Hz CODE-NO

DA02-40030A DA59-00158A

ITEM CODE-NO
THERAFLUOROETHANE DA02-00038A COMPRESSOR

R-600a

R-134a DK172Q-L2U
DA59-00144A DK4A1Q-L1U DA59-00158A
PROTECTOR-O/L DA34-10003H 4TM213PHBYY-53 DA34-10003K 4TM232SHBYY-53 DA34-10003K 4TM232SHBYY-53 C-OIL RELAY-PTC DC-TRANS EVAP-ASSY 2501-001185 3.5uF, 350V 2501-001186 5uF, 350V 2501-001186 5uF, 350V