PROJECTION TV RECEIVER

Chassis : Model: J54A(P) C2.0 SP43T7HFS/XST SP55W3HCX/FES SP62T6HCX/HAC SP47W3HCX/FES

d&

ou n Le kS

CONTENTS

1. Alignment and Adjustments 2. Exploded View and Parts List 3. Electric Parts List 4. PCB Diagrams 5. Schematic Diagrams
Alignment and Adjustments
1. Alignment and Adjustments
1-1 When entering the service mode;
1. Turn on the TV, and then select DYNAMIC on the picture adjustment mode. 2. Turn off the TV(STAND-BY). 3. Enter the service mode by pressing the remote control keys in the following sequence: Note : If necessary, re-do steps 1~3. Initial display when the service mode is switched.
1-1-1 WHEN A RF SIGNAL IS RECEIVED
MODEL((T_CM2P06_002) DEFLECTION VIDEO ADJUST 1 VIDEO ADJUST 2 VIDEO ADJUST 3 VIDEO ADJUST 4 OPTION (87h 05ch) YC DELAY RESET T_CM2906_002 yy.mm.dd

MODEL(T_CMDEAC_XXX)

1-1-2 SERVICE MODE CONTROL KEYS

MAIN MENU UP / DOWN

RIGHT / LEFT
MENU DISPLAY Select item by moving cursor Decrease or increase the adjustment values

[Navigation Key]

PRECAUTIONS
1. When EEPROM IC (IC902) is replaced, first connect the power cord and wait for about 4~5 seconds. 2. After replacing EEPROM IC (IC902), enter the Service mode. Next, enter the standard data or the previous EEPROM IC data before replacement. And then check and adjust any items related to Geometric, Picture, Option.

Samsung Electronics

DEFLECTION VIDEO ADJUST 1 VIDEO ADJUST 2 VIDEO ADJUST 3 VIDEO ADJUST 4 OPTION (EF 8E 2E) YC DELAY RESET T_CMDEAC_XXX yy.mm.dd 1-1
Display -> Menu -> Mute -> Power ON

1-2 FACTORY MODE MENU

1-2-1 MODEL(T_CM2906_002)

1-2-1(A) DEFLECTION

Item V Amp V Shift H EW H Shift V Linearity Upper Linearity Lower Linearity V SC H Parabolra Upper Corner Lower Corner H Trapezium Bow Angle V Position Up UCG Lo UCG CXA Left Blk Range 0 ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ 63 Initial Data 4:7 Wide Remark Variable

0~ 3 0~ ~ 63

CXA Right Blk

0 ~ 63

FIX Variable FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX Samsung Electronics

1-2-1(B) VIDEO ADJUST1

Item R Cutoff G Cutoff B Cutoff Color On/Off CB Offset CR Offset R Drive G Drive B Drive Sub Bright Sub Contrast Sub Color Sut Tint CTI Level COL Axis LTI Level VSU Melody Volume LIT Mode System Range 0 ~ ~ ~ 63 0~ ~ ~ ~ ~ ~ ~ ~ ~ ~ 63 0~ 3 0~ 3 0~ 3 Initial Data Remark Variable FIX Variable Variable

0 ~ ~ 20

0~ 3 0~ 3
Variable Variable Variable FIX Variable Variable Variable FIX FIX FIX FIX FIX FIX FIX FIX FIX 1-3

1-2-1(C) VIDEO ADJUST2

Item ABL Level Gamma DPIC Level DC Trans ABL TH VM Level VM Corint VM f0 VM Limit VM Delay SHP CD SHP f0 SHP f1 & P/O AKB Time BandPass 9407 HighPass 9407 S ABL P ABL Range 0~ 3 0~ 3 0~ 3 0~ ~ 15 0~ ~ 15 0~ 3 0~ 3 0~ 3 0~ 3 0/~ 63 Initial Data Remark FIX FIX FIX

0~ ~ 15

FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX Samsung Electronics

1-2-1(D) VIDEO ADJUST3

Item H Comp V Comp Pin Comp AFC Comp H-Sync Phase NR Off Value CG HAO CG VAO NR High Ref NR Low Ref NR High Value NR Low Value NR Hight Ref(S) NR Low Ref(s) NR High Value(S) NR Low Value(S) NR Read M/S Range 0 ~ ~ 15 0~ 7 0~ 7 0/1 0~ ~ ~ ~~~~~~~~255 0/27 Initial Data 4:0 Wide Remark

1-2-1(E) VIDEO ADJUST4

Item SECAM Color Main SECAM Color Pip Picture Limit OSD Contrast TTX Contrast Range 0 ~~255 0~ ~ ~ 15 Initial Data 3 FIX Remark

1-2-1(F) OPTION

Item SYSTEM SOUND ASPECT WIDE 4:3 X-RAY AUTO FM PIP LNA Letter Box TTX Lang.Grp AGC Setting Data CS/CW
Appliance CS CS Dolby Prlogic ON ON ON ON ON OFF OFF
A2-NICAM/Dolby-Prologic WIDE / 4:3 ON/OFF
ON/OFF ON/OFF ON/OFF ON/OFF ON/OFF
West/East/CIS/Turk&Grk ON/OFF ON/OFF

Natural Zoom

Remark Area Option Inch Option Inch Option Area Option Samsung Electronics

1-2-1(G) YC DELAY

Item P.YC(AV) Delay S.YC(AV) Delay N.YC(AV) Delay P.BG.YC Dealy P.DK.YC Delay P.I.YC Delay P.M.YC Delay P.N.YC Delay S.BG.YC Delay S.DK.YC Delay S.I.YC Delay S.M.YC Delay S.L.YC Delay N.M.YC Delay N4.43 YC Delay Range 1 -1

Vi s d&

0 -7 -9 -9 -7 --6 1-7

200-channle ON

OFF ON 2-TUNER ON ON OFF RCA+DVD ON ON OFF WEST EUROPE OFF OFF OFF OFF
OFF ON ON OFF OFF OFF OFF

RCA+1SCART+DVD

TTX LANG
WEST EUROPE / EAST EUROPE RUSSIAN / GREEK-TURKEY ARABIC / FARSI / AREB-HEBREW OFF / ON OFF / ON OFF / ON OFF/ON

0N(AUSTRALIA)

WEST EUROPE
AGC AV MEMORY AUSTRALIA CG BRIGHT

OFF/0N(Thailand)

ON ON ON 2-TUNER ON ON OFF ON ON OFF ARABIC OFF OFF OFF OFF

250-channle

1-2-2(G) YC DELAY
Item P.YC(AV) Delay S.YC(AV) Delay N.YC(AV) Delay P.BG.YC Dealy P.DK.YC Delay P.I.YC Delay P.M.YC Delay P.N.YC Delay S.BG.YC Delay S.DK.YC Delay S.I.YC Delay S.M.YC Delay S.L.YC Delay N.M.YC Delay N.443.YC Delay Range 1 -1

0 -7 -10 -9 -7 --1 1-13

-2 -2 0
1-3 Screen Change (When Adjusting I2C Bus Geometric Items)

V - S - CORRECTION

V SHIFT

H Parabolra

4 H SHIFT 9 BOW

V LINEARITY

8 H Trapezium 10 ANGLE

1-4 Other Adjustments

1-4-1 Screen Adjustment
1. Warm up the TV for at least 30 minutes. 2. Select the DYNAMIC Video mode. 3. Trun to the Video Mode(No Signal) using a remote-control. 4. Connect an oscilloscope to RK, GK, BK. 5. Adjust the VR (VR501, VR531, VR561) screen so that RK, GK, BK pulse is 20Vp-p each. (Turn the R,G,B VR screen fully counterclockwise in the area of each flyback line.) 3. Select Sub-Bright by pressing the Volume +/keys. 4. Adjust so that the 63 step on the right side of the screen is not seen (Use the Volume +/keys). 5. Press the Menu key to exit. keys in the following sequence : Displsy Menu Mute Power ON
1-4-4 High Voltage (29KV) Check

PRECAUTION

1. Input a lion head pattern.
1-4-2 White Balance Adjustment
1. Select the DYNAMIC video mode. 2. Input 100% white pattern.
4. Warm up the TV for at least 30 minutes. 5. Input a 10-step signal.
6. R-cut off, B-cut off, and G-cut off by pressing the Volume +/- keys. 7. Adjust the low light with viewing the dark side of the screen.
8. Select R-drive, G-drive and B-drive by pressing the Volume +/- keys. 9. Adjust the high light with viewing the light side of the screen. 10. If necessary, redo adjustments 6~9. 11. Press the Menu key to exit.
1-4-3 Sub-Brightness Adjustment
1. Input a sub-brightness adjustment signal. (TOSHIBA PATTERN) 2. In the stand-by mode, press the remote-control
3. In the stand-by mode, press the remote-control keys in the following sequence: Displsy Menu Mute Power ON

ADJUSTMENT

2. Select DYNAMIC video mode. 3. Warm up the TV for at least 10 minutes. 4. Use a 1000:1 probe.
1. Connect the (+) terminal of the 10000:1 probe to the high voltage distributor and the(-) terminal to GND(located on the deflection board). 2. Adjust RR471S (located on the deflection board) so that the digital meter indicates DC290V 0.1V.

4-4-5 F.S. (Fail Safe) Circuit Check
Note : The finished product has a well-mounted VR(RR402S). If necessary, do the F.S adjustments in the following sequece. 1. Use a digital multimeter. 2. Connect the digital multimeter to the JIG pin (DZ482S) terminals. 3. Adjust VR(RR402S) so that the voltage becoms 2.25V. 4. After the adjustments are complete be sure to mount VR(RR402S) correctly.
1-4-6 Static Focus Adjustment
1. Select the DYNAMIC video mode. 2. Input a crosshatch pattern. 3. Cover the lenses that are not being adjusted. 4. Connect a convergence jig and read data. 5. Adjust the lens for best focus. (See Fig, 4-1) 5. Green lens adjustment: Set the lens at the point where Blue just changes to Red. If the color aberration is irregular throughout the picture screen, adjust the lens to show Red color aberration (approximately 1~3 mm area) within a 3-block grid around the horizontal center-line. If the color aberration is irregular, adjust the lens as shown in the diagram below. (Accurate alignment of Green is important for overall color quality.) 6. Red lens adjustment Set the Red lens at the point where Orange becomes Crimson. 7. Blue lens adjustment Set the Blue lens at the point where Purple becomes Green.

P L1 L2

4. When the lens is turned clockwise, the color aberration will change as follows: Lens R G B Color Aberration Change Orange - Crimson Blue - Red Purple - Green

STATIC FOCUS (CONTINUED)

Vary the focus pack VR (Red, Blue) on the front cabinet. Adjust the TV for best possible focus around the center of the crosshatch pattern, without losing overall screen balance. Figure Crosshatch Pattern Examine these points together.
Examine these points together
Fig. 4-1 Crosshatch Pattern.
1-4-7 Lens Focus Adjustment

PRECAUTIONS

1. Do this adjustment after the static focus adjustment and the tilt adjustment. 2. Select the DYNAMIC video mode. (Contrast:100, Brightness:50)
3. Input a crosshatch pattern.
1. Loosen the lens screws. 2. Cover the two lenses that are not being adjusted. 3. Adjust the lens, observing the color aberration vertically and horizontally within 3 blocks of the center of the crosshatch pattern.

RED ABERRATION BLUE ABERRATION < L1, L2_ P
Fig. 4-2 Color Aberration
1-5 Beam alignment Adjustments
1. Select the DYNAMIC video mode. 2. Warm up the set at least for 10 minutes. 3. Enter the Convergence mode by pressing the remote control buttons in the following sequence :
4. Set the Beam Alignment Adjustment CY to Zero magnetic field area.
(Creation of CPM Zero Magnet)
(Creation of the 2-pole/4-pole zero magnets)
5. Check the squarewave at the point where the focus is misaligned. 6. Press the 7. Adjust the Focus-pack VR for defocusing. (Use

G-FOCUS

8. Mute the other patterns (R/B) other than G-PATTERN. /
buttons on the remote control.)
(When VM 2-Pole Adjustment is completed)

(Varying G-Focus Pack)

Varying the 2-pole of VM Varying the 4-pole of VM
9. Adjust the 2, 4 polarities of VM-COIL as shown in figure below. 10. Adjust the G-Focus until any light around the core disappears. 11. Adjust G-Focus so that the surrounding flash can disappear from the spot. 12. After G-Focus adjustments are complete, adjust R-Focus as above procedures. 13. The B-CRT adjustments can be omitted because the variance of beam focus is small. (Only Vm-coil is mounted.) 14. Adjust the Focus-pack VR for fine focusing. 15. Press the mode. 16. Press the
button on the remote control, and the mode changes to the Convergence Adjustment button on the remote control to return to normal viewing.
button on the remote control during 3~5 sec and vibrating dot-pattern appears.
(Positioning the Core in the Center)
(Adjust until the light around the core becomes a circle)

1-6 High Voltage Part

1-6-1 PWM REG Circuit
For the existing high voltage REG circuit (input voltage variation type), a dynamic REG response is not provided. So it is difficult for both beam linearity and uniformity in screen size to be maintained on the screen with rapidly changing beams. A PWM (Pulse Width Modulation) type of high voltage, however, provides the maintenance of beam linearity and uniformity in screen size via a quick response to beam change by performing sync lock every 1H line, and detecting beam fluctuation at 1H line, and then controlling the IC current of high voltage output circuit. 1. High Voltage Fluctuation Detect (DC Detect) FBT pin 11 detects DC high voltage fluctuation. The detected DC high voltage value is input to PWM IC471 pin1 through R473, VR471, R471, and then it is input to a differential AMP circuit that differentiates the gap after comparing with the reference voltage input to pin2. 2. High Voltage Fluctuation Detect (AC Detect) 3. PWM IC OSC Sync Lock A PWM type IC needs sync lock for PWM pulse and horizontal scan line. The standard time constant of OSC circuit is determined by C487, R475 (PWM IC pins 5 and 6). And the standard OSC frequency is about 27 kHz. The horizontal frequency of scan line is 31.5kHz(NT), 31.25kHz(PAL), so sync lock for this horizontal frequency should be performed using sync lock circuit. The sync lock circuit consists of Q481(Tr KSC815-Y), D479, D478, and C492. The input AFC signal is connected to PWM IC pin 5 through D479 so that it can be negative Trig.

To check AC high voltage fluctuation, the output from FBT is detected by using a capacitor inside the high voltage distributor. The detection of AC high voltage fluctuation, a detection of dynamic beam current change is required in order to keep beam linearity and uniformity in size. Regarding the capacitor, a capacity of less than 3000P should be applied to a PWM type. (The existing type needs a capacity of about 6000P.) AC detect circuit eliminates unnecessary high frequency by using C476, D472. Also, AC gain is limited to + / - 0.7V (D472). This AC gain is combined with the detection value of DC high voltage fluctuation by using C478.
4. Dead Time (HV Protect) Dead Time (PWM IN pin4) consists of C481, delays high voltage for a certain time to soft start in power on, a x-ray protection circuit. The voltage of Dead Time is detected by FBT pin7 and through DC Feedback. The normal voltage of Dead Time is +27V. When high voltage increases, however, detected voltage is in proportion to high voltage. Then, the detected voltage is applied to ICR01S(TL431). If the voltage is over 2.5V (normal:about 2.25V), TL431 turns ON, the base port of QR401S becomes low, and then an emitter current flows. At this time, a high voltage protection point is set. When QR401S turns ON, high voltage is applied to PWM IC pin4 and then muted.

OSC : 27KHz

AFC Waveform : 31.5KHz(NT)
Locked OSC Waveform : 31.5KHz
5. Output Circuit The voltages, which are detected form an error detection circuit of PWM IC (Differential AMP) and Dead Time, each is applied to PWM conparator. Due to these detection coltages, Q1, Q2 (Output TR) parallel operate. Q482 (External TR), however, functions as a buffer; natches inpedance between the output port of PWM IC and the final output TR(IRFS640). The PWM pulse (applied to the final output FET (IRFS640 GATE) varies the IC current of high voltage TR(Q473) by adjusting the load impedance of starage Trans (T431). Due to this variation of current, the gain for Q473 emitter pulse changes T444(FBT)makes this emitter pulse became high voltage. Such change keeps both dynamic and static changes fixed. The output waveform of high valtage TR emitter is as shown in the figure below.
about 1V. A PWM modulation type REG detects static, dynamic high voltage fluctuation for only Ton Time (when the current of the output TR collector flows) each 1H, and modulates the width of PWM pulse. So, this PWM type has better improvement in the characteristic of high voltage REG as compared to the existing type.
High Voltage Drive Base Current
6. Paraneters according to beam
To maintain the set high voltage value (31kV), parmaters such as +Ve (DC), Vcp High Voltage change (See the table below).

Vi s Le kS

Factor of high voltage change Parameters Width of FET Gate Pulse + Ve (DC) Vcp High Voltage Beam (High voltage Beam (High voltage ) )
8. Application Effects 1) Improvement of horizontal size fluctuation 2) Linearity improved 3) Embodiment of X-ray protection circuit The figures below show characteristics when a PWM high voltage REG circuit is applied.

PWM Variation tange

PWM Input Waveform of FET GATE
7. Response Waveform To reduce unstable high voltage fluctuation, the existing high voltage type REG circuit controls dynamic fluctuation by using C-block capacitor. But, it can't detect actual dynamic fluctuation. Also, its velocity of response to static fluctuation is late because +B power supply changes per
PWM type When a Toshiba Pattern is recrived, the screen is displayed as shown in figute side Existing type
Ton Toff High Voltage Beam High Voltage OFF High Voltage REG ON BLACK WHITE

1-6 SCREEN-JIG

1-6-1 42W5
42W5 Screen Size : X 932, Y 524 (X:764 = 22 x 2 + 60 x 12, Y:262 = 17 x 2 + 38 x 6)-PAL MODE

2 6.m m 7 3.m m 2 6.m m

3 4.m m

7 6.m m

1-6-2 47W3
47W3 Screen Size : X 1045, Y 588 (X:764 = 22 x 2 + 60 x 12, Y:262 = 17 x 2 + 38 x 6)-PAL MODE

3 0.m m 8 2.m m 3 0.m m

3 8.m m

8 5.m m

1-6-3 55W3
55W3 Screen Size : X 1225, Y 686 (X:764 = 22 x 2 + 60 x 12, Y:262 = 17 x 2 + 38 x 6)-PAL MODE

3 5.m m 9 6.m m 3 5.m m

4 4.m m

9 9.m m

1-6-4 65W3
65W3 Screen Size : X 1442, Y 838 (X:764 = 22 x 2 + 60 x 12, Y:262 = 17 x 2 + 38 x 6)-PAL MODE

4 1.m m

4 1.m m 5 4.m m 5 4.m m

1-6-5 43T6/43T7

43T6 Screen Size : X 885, Y 666 (X:764 = 22 x 2 + 60 x 12, Y:262 = 17 x 2 + 38 x 6)-PAL MODE

2 5.m m 6 9.m m 2 5.m m

4 3.m m

9 6.m m

1-6-6 48T6
48T6 Screen Size : X 973.4 Y 738.4 (X:764 = 22 x 2 + 60 x 12, Y:262 = 17 x 2 + 38 x 6)-PAL MODE

2 8.m m

2 8.m m 4 7.m m 4 7.m m

1-6-7 54T6

54T6 Screen Size : X 1099 Y 823 (X:764 = 22 x 2 + 60 x 12, Y:262 = 17 x 2 + 38 x 6)-PAL MODE

3 1.m m 8 6.m m 3 1.m m

5 3.m m

1-6-8 62T6

62T6 Screen Size : X 1259.4, Y 948 (X:764 = 22 x 2 + 60 x 12, Y:262 = 17 x 2 + 38 x 6)-PAL MODE

3 6.m m 9 8.m m 3 6.m m

6 1.m m
1-7 Remote Control for Servicing(Convergence Mode)
Convergence Data LINE Adjust ENTIRE Adjust G-Mute R-Mute B-Mute Exit Button
Mute VOL Surround S.STD P.STD
Last Data Save button/Canccel Cg Factory Data Select Key(Each Inch) R-Selete B-Selete G-Selete

TV S.Mode

Test Normal
Display Text/Mix PIP ON Info. Scan

Menu Swap

Convergence Data Left/Right Move Button
Convergence H-PHASE Move Button(Left)
Still P Video P.Size Sleep Perfect Focus Locate
Save Button Convergence Data UP/DOWN Move Button Convergence Data UP/DOWN Move Button Convergence H-PHASE Move Button(Right)

1-7-1 KEY Function

1. R-SELECT Press to select RED color. 2. G-SELECT Press to select GREEN color. 3. B-SELECT Press to select BLUE color.
TV 6. B-MUTE Press to mute BLUE color.
7. CANCEL KEY Press to revert to the previous data during the Convergence Adjustment. 8. TEST/NORMAL Press to check TV mode in the Convergence Mode. 9. LINE SHIFT Press to move a line up/down or left/right.

Display

10. FACTORY DATA SELECT BUTTON Press to call the factory default values.

S.Mode

11. SAVE BUTTON After the Convergence Adjustments are completed, press to save data.
12. EXIT BUTTON After the Convergence adjustments are completed, press to exit to TV mode.
5. G-MUTE Press to mute GREEN color.
4. R-MUTE Press to mute RED color.
13. CURSOR MOVE BUTTON Press to move the cursor up/down or right/left. !

UP DOWN LEFT RIGHT

14. CONVERGENCE PICTURE MOVE BUTTON

(Right)

(Left)

(Down)

15. CONVERGENCE MOVE BUTTON Press to move the convergence right (

PIP ON

Cg -Data Move Button

) or left (

16. CONVERGENCE DATA ZERO BUTTON Press to zero the convergence correction data.

). Samsung Electronics

# (Mute) Press to move the cursor left or up. (Video) Press to move the cursor right or down. (Menu) Press switch the cursor direction horizontally or vertically.
17. INITIAL DATA SET BUTTON Changes when applying Almighty-Cg, Module (How to extract the basic Cg Data) Model Name Inch (Type) Representative Model SP42W5 SP47W3 SP55W3 SP43T6 SP43T7 SP48T6 SP54T6 SP62T6 SP65W3 Basic Data Number after entring the Cg-Mode 5-425 (Press in regular order) 5-473(Press in regular order) 5-553(Press in regular order) 5-436(Press in regular order) 5-437(Press in regular order) 5-485(Press in regular order) 5-545(Press in regular order) 5-625(Press in regular order) Screen Display
42 (42W5) 47 (47W3) 55 (55W3) 43 (43T(43T7) 48 (48T6) 54 (54T6) 62 (62T6) 65(65W3)

18. Data shift Button

Locate
Press to transmit data(PAL Mode/NTSC Mode).
1-8 Convergence Adjustment
1-8-1 Convergence Adjustment
Special Notes A sensor is attached on the center of each side of the Convergence Mode pattern (see figure below). The sensors are required for normal Perfect Focus function.
Do the convergence adjustments correctly. Otherwise, any Perfect Focus error can happen.
1. Warm up the TV for a least 30 minutes. 2. Input an PAL Signal.(Use an antenna or AV source.)
Make sure that deflection yoke are properly adjusted so that the center of Green, Red, Blue pattern is aligned on the center of screen jig.
3. Enter the Convergence Mode by Pressing the remote control keys in the following sequence:
If OSD displayed as shown in figure below, press the key to exit. Then, redo step 3 to enter the Convergence Mode. After entering the Convergence Mode, Stand by for about five seconds before doing the adjustments.
Use a screen jig to do the convergence adjustments correctly (Especially, perform correct convergence adjustments on the center of each side where a sensor is located.)

Menu Mute

P.Size

LINE Adjust

1-8-2 Perfect Focus(Factory Mode)

Up, Down

Left, Right
Perfect Focus Process : 83%
Perfect Focus Process : 83% Exit

1-9 MICOM and Pins Voltage
1-9-1 Pin Layout(T_CM2P06_XXX)
1080i-SW SCL1 SDA1 SCAN-RST N.C VS2 HS2 N.C OSD-YS/YM ST3.3A GND XTAL1 XTAL2 GND ST2.5A OSD-R OSD-G OSD-B GND ST2.5A GND GNA ST2.5A GND TTX-CVBS GND ST2.5A KEYS1 KEYS2 MAIN-AFT SUB-AFT GND

127 128

SDA6001-B11 (T_CM2P06_XXX)
D2 D12 D10 GND ST3.3B D4 D3 D11 RESET SCL2 SDA2 IR COMP | SW ST5V PROTECT WP S | RESET AMP | MUTE DEFL | SW GND ST3.3A GND ST2.5B TXD RXD LED1 LED2 STOP N.C N.C T1 T96 D5 D9 D13 ST3.3B GND D1 D6 D8 D14 D0 D7 ST3.3B GND D15 WR LDQM UDQM RD CSROM CLKEN CSSDRAM CLKSDRAM ST3.3B GND A15/CAS A14/RAS A13 A0 A1 A2 A3 A1 ST3.3B GND A12 A11 A10 A5 A6 A9 A7 A8 A16 ST2.5B GND A17 A18 A19 ST3.3B ST3.3B ST3.3A GND MAIN | SW1 MAIN | SW2 SUB | SW1 SUB | SW2 5VB AV | LINK ST5V C | SPK | MUTE TDO TDI TMS TCK
1-9-2 Pin Layout(T_CMDEAC_XXX)
A8 A6 A9 A5 A11 A4 LE PSEN A3 A10 GND 3.3V A2 A1 N.C DO7 A0 D06 D00 D51 N.C A7 A13 A12 A14 3.3V GND 2.5V N.C A15 A17 A16 N.C N.C N.C N.C N.C N.C N.C N.C OSD-F/B OSD-B OSD-G OSG-R 2.5V GND N.C XTAL1 XTAL2 N.C
DO1 DO4 DO2 DO3 GND 2.5V GND 3.3V W.P SDA2 SCL2 BUS-STOP SDA1 SCL1 S-RESET V-MUTE GND N.C N.C GND TTX-CVBS 2.5V GND MAIN-AFT SUB-AFT KEY2 KEY1 N.C H-BLK V-BLK
30 RESET N.C N.C 1080I POWER AMP MUTE N.C SW3/SW2 N.C N.C 3.3V GND N.C STD LED TIMER LED PROTECT IR C/SPK MUTE N.C N.C N.C

1-9-3 MICOM MODULE Pins

PIN NO. KEY 1
FUNCTION KEY SCAN1 PROTECT PORT KEY SCAN2 GND N.C VCC REMOCON INPUT POWER ON/OFF RELAY CONTROL TIMER LED N.C GND VIDEO RESET
OUT VOLT 2.28[V) 0.83[mV] 2.25[V] -
PROTECT KEY 2 GND N.C STB-5(V) IR IN POWER TIMER-LED N.C GND V-RESET SCL1 GND SDA1 S-RESET ST-BY-LED RESET AMP-MUTE N.C

SERIAL CLOCK LINE1 GND

SOUND RESET STAND-BY LED RESET SOUND AMP MUTE N.C GND N.C SERIAL CLOCK LINE2 CENTER SPEAKER MUTE SERIAL DATA LINE2 SW3(CONTROL) GND SW2(CONTROL) SUB TUNER AFT CONTROL GND MAIN TUNER AFT CONTROL IIC BUS STOP

SEREAL DATA LINE1

GND N.C

C-SPK MUTE SDA2 SW3 GND

SUB-AFT GND MAIN-AFT BUS-STOP
4.91[V] 3.74[V] 1.03[V] 2.07[V] 2.84[mV] 3.43[V] 3.49[V] 4.21[V] 2.95[V] 2.47[V] 0.89[mV] 3.27[V] 3.26[V] 3.27[V] 5[mV] 2.08[V] 2.57[V] 1.04[V] 3.27[V] 1-35

PIN NO. 5[V]

ITEM 5[V]

FUNCTION

OUT VOLT 4.96[V] 215.8[mV] -12.10[mV]

H-BLANK GND V-BLANK N.C GND GND N.C VS1 N.C HS1 N.C GND N.C TTX-CVBS GND GND N.C AN-LINK N.C
HORIZONTAL BLANK GND VERTICAL BLANK N.C GND GND N.C VERTICAL SYNC N.C HORIZONTAL SYNC N.C GND N.C
GND GND N.C NOT USE N.C GND N.C N.C GND N.C ON SCREEN DISPLAY RED GND ON SCREEN DISPLAY GREEN WRITE PROTECT ON SCREEN DISPLAY BLUE 3.3[V] OSD/TTX-FB

TTX/CAPTION-CVBS

GND N.C N.C

OSD-TTX-R GND

OSD-TTX-G WP OSD-TTX-B 3.3[V]

OSD-TTX-FB

215.51[mV] 1.19[V] 168[mV] 0.46[V] 0.46[V] 3.26[V] 7.31[mV] Samsung Electronics
1-9-4 PROSCAN MODULE Pins

PIN NO. EW

FUNCTION EAST WEST OUT VERTICAL BLANK ABL(Automatic Brightness Limiter) VERTICAL DRIVE(-VOLTAGE) VERTICAL DRIVE(+VOLTAGE) HORIZONTAL BLANK HORIZONTAL DRIVE GND OSD/TTX-FB
OUT VOLT 2.26[V] -12.07[mV] 2.26[V] 3.46[V]
V-BLK ABL VDVD+ H-BLK HD GND OSD/TTX-FB OSD/TTX-B OSD/TTX-G OSD/TTX-R V-RESET GND SCL1 SDA1 N.C COMP GND
ON SCREEN DISPLAY BLUE IN
ON SCREEN DISPLAY GREEN IN ON SCREEN DISPLAY RED IN VIDEO RESET GND
SERIAL DATA LINE N.C COMP GND CONVERGENCE RED CONVERGENCE GREEN CONVERGENCE BLUE CONVERGENCE SYNC DYNAMIC FOCUS GND 9[V] N.C N.C N.C N.C GND 13.5[V]

SERIAL CLOCK LINE

CG-G CG-B

CG-SYNC D/F

GND 9[V] N.C N.C N.C N.C GND

13.5[V]

3.53[V[ 215.93[mV] 2.38[V] 7.29[mV] 0.46[mV] 0.46[mV] 167.99[mV] 2.94[mV] 3.42[V] 3.50[V] 27.28[mV] 0.27[mV] 0.27[mV] 0.29[mV] 180.03[mV] 1.5[V] 9[V] 14.05[V] 1-37

PIN NO. 63 64

ITEM 5[V]-DW1 VM-Y SW3 SW2 N.C GND PIP-C PIP-Y CVBS GND MAIN-C MAIN-Y CVBS N.C GND N.C GND RF2-CVBS DVD-Pr/R DVD-Y/G DVD-Pb/B FB 5[V]-DW1
OUT VOLT 4.97[V] 1.97[V] 4.98[mV] 2.08[V]
VM-Y OUTPUT SW3(CONTROL) SW2(CONTROL) N.C GND PIP-C INPUT PIP-Y/CVBS INPUT GND MAIN-C INPUT MAIN-Y/CVBS INPUT N.C GND N.C GND
RF2-CVBS DVD-Pr/R(SCART) DVD-Y/G(SCART) DVD-Pb/B(SCART) FB(SCART) GND N.C N.C N.C GND DVD-Pr DVD-Y DVD-Pb GND 5[V]-DW2 N.C N.C

GND N.C N.C N.C

DVD-Pr DVD-Y

DVD-Pb GND

5[V]-DW2 N.C N.C
1.20[mV] 1.33[mV] 1.34[mV] 1.57[mV] 4.89[V] Samsung Electronics
1-9-5 CONVERGENCE MODULE Pins

PIN NO. 31 32

ITEM 5[V]-CG GND D/F GND SCL1 CG-SYNC GND N.C CG-R CG-G CG-B SDA1 N.C IR N.C GND GND GND BV 5[V]-CG GND

OUT VOLT 5.2[V] 1.5[V] -

DYNAMIC FOCUS GND SERIAL CLOCK LINE1 CONVERGENCE SYNC GND N.C CONVERGENCE RED CONVERGENCE GREEN CONVERGENCE BLUE SERIAL DATA LINE1 N.C

INPUT REMOCON N.C

GND GND GND BLUE VERTICAL OUT BLUE HORIZONTAL OUT GREEN VERTICAL OUT GREEN HORIZONTAL OUT RED VERTICAL OUT RED HORIZONTAL OUT GND HORIZONTAL BLANK VERTICAL BLANK GND N.C -5[V] 5[V] GND
H-BLK V-BLK GND N.C -5[V] 5[V] GND
3.4[V] 179[mV] 5.2[V] 0.27[mV] 0.26[mV] 0.29[mV] 3.5[V] 3.7[V] 34.27[mV] -107.32[mV] 101.52[mV] -15.83[mV] 104.32[mV] -88.95[mV] 275[mV] -13.22[mV] -4.99[V] 5.24[V] 1-39

5. Schematic Diagrams

5-1 MAIN 1

Schematic Diagrams

5-2 MAIN 2

'5 io n Vi s un d&

TP03 TP04 TP05

5-3 MAIN 3

'5 io n Vi s d&

TP06 TP07

5-4 MAIN 4
TP12 TP14 TP13 TP11 TP10 TP09 TP08

TP14 TP08 TP15 TP09

TP15 TP16 TP17 TP18 TP19 TP20

TP16 TP10

5-5 T_CM2906_002 MICOM

5-6 T_CMDEAC_XXX MICOM

5-7 CRT

5-8 SUB 1

'5 io n

5-9 SUB 2

io n Vi s
5-10 CONVERGENCE ( SDC12 - 1 )
5-11 CONVERGENCE ( SDC12 - 2 )

5-12 PRO SCAN 1

5-13 PRO SCAN 2

5-14 AV FRONT

5-15 VM

5-16 CONTROL

5-17 DY JACK, SENSOR

DY JACK

SENSOR

5-18 CG AMP

5-19 SUB AMP

PROJECTION TV RECEIVER

Chassis : Model: J54A(P) C2.0 SP43T7HF1X/BOB SP43T7HF1X/EUE SP42W5HF1X/XEG SP42W5HFX/XEU

CONTENTS

1. Alignment and Adjustments 2. Exploded View and Parts List 3. Electric Parts List 4. PCB Diagrams 5. Schematic Diagrams

ELECTRONICS

Samsung Electronics Co., Ltd. Apr. 2003
Printed in Korea AA82-00512A
Alignment and Adjustments
1. Alignment and Adjustments
1-1 When entering the service mode;
1. Turn on the TV, and then select DYNAMIC on the picture adjustment mode. 2. Turn off the TV(STAND-BY). 3. Enter the service mode by pressing the remote control keys in the following sequence: Display -> Menu -> Mute -> Power ON Note : If necessary, re-do steps 1~3. Initial display when the service mode is switched.
1-1-1 WHEN A RF SIGNAL IS RECEIVED
MODEL((T_CM2P06_002) DEFLECTION VIDEO ADJUST 1 VIDEO ADJUST 2 VIDEO ADJUST 3 VIDEO ADJUST 4 OPTION (87h 05ch) YC DELAY RESET T_CM2906_002 yy.mm.dd MODEL(T_CMDEAC_XXX) DEFLECTION VIDEO ADJUST 1 VIDEO ADJUST 2 VIDEO ADJUST 3 VIDEO ADJUST 4 OPTION (EF 8E 2E) YC DELAY RESET T_CMDEAC_XXX yy.mm.dd
1-1-2 SERVICE MODE CONTROL KEYS
MAIN MENU UP / DOWN RIGHT / LEFT MENU DISPLAY Select item by moving cursor Decrease or increase the adjustment values

[Navigation Key]

PRECAUTIONS
1. When EEPROM IC (IC902) is replaced, first connect the power cord and wait for about 4~5 seconds. 2. After replacing EEPROM IC (IC902), enter the Service mode. Next, enter the standard data or the previous EEPROM IC data before replacement. And then check and adjust any items related to Geometric, Picture, Option.

Samsung Electronics

1-2 FACTORY MODE MENU
1-2-1 MODEL(T_CM2906_002)

1-2-1(A) DEFLECTION

Item V Amp V Shift H EW H Shift V Linearity Upper Linearity Lower Linearity V SC H Parabolra Upper Corner Lower Corner H Trapezium Bow Angle V Position Up UCG Lo UCG CXA Left Blk CXA Right Blk Range 0 ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ 63 0~ 3 0~ ~ ~ Initial Data 4:Wide Remark Variable FIX Variable FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX

1-2-1(B) VIDEO ADJUST1

Item R Cutoff G Cutoff B Cutoff Color On/Off CB Offset CR Offset R Drive G Drive B Drive Sub Bright Sub Contrast Sub Color Sut Tint CTI Level COL Axis LTI Level VSU Melody Volume LIT Mode System Range 0 ~ ~ ~ 63 0~ ~ ~ ~ ~ ~ ~ ~ ~ ~ 63 0~ 3 0~ 3 0~ ~ ~ 20 0~ 3 0~ 3 Initial Data Remark Variable FIX Variable Variable Variable Variable Variable FIX Variable Variable Variable FIX FIX FIX FIX FIX FIX FIX FIX FIX

1-2-1(C) VIDEO ADJUST2

Item ABL Level Gamma DPIC Level DC Trans ABL TH VM Level VM Corint VM f0 VM Limit VM Delay SHP CD SHP f0 SHP f1 & P/O AKB Time BandPass 9407 HighPass 9407 S ABL P ABL Range 0~ 3 0~ 3 0~ 3 0~ ~ 15 0~ ~ 15 0~ 3 0~ 3 0~ 3 0~ 3 0/~ 63 0~ ~ 15 Initial Data Remark FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX

1-2-1(D) VIDEO ADJUST3

Item H Comp V Comp Pin Comp AFC Comp H-Sync Phase NR Off Value CG HAO CG VAO NR High Ref NR Low Ref NR High Value NR Low Value NR Hight Ref(S) NR Low Ref(s) NR High Value(S) NR Low Value(S) NR Read M/S Range 0 ~ ~ 15 0~ 7 0~ 7 0/1 0~ ~ ~ ~~~~~~~~255 0/Initial Data 4:FIX Wide Remark

1-2-1(E) VIDEO ADJUST4

Item SECAM Color Main SECAM Color Pip Picture Limit OSD Contrast TTX Contrast Range 0 ~~255 0~ ~ ~ 15 Initial Data 3 FIX Remark

1-2-1(F) OPTION

Item SYSTEM SOUND ASPECT WIDE 4:3 X-RAY AUTO FM PIP LNA Letter Box TTX Lang.Grp AGC Natural Zoom Setting Data CS/CW A2-NICAM/Dolby-Prologic WIDE / 4:3 ON/OFF ON/OFF ON/OFF ON/OFF ON/OFF ON/OFF West/East/CIS/Turk&Grk ON/OFF ON/OFF Appliance CW CW CS CS Dolby Prlogic ON ON ON ON ON OFF OFF Area Option Inch Option Inch Option Area Option Remark

1-2-1(G) YC DELAY

Item P.YC(AV) Delay S.YC(AV) Delay N.YC(AV) Delay P.BG.YC Dealy P.DK.YC Delay P.I.YC Delay P.M.YC Delay P.N.YC Delay S.BG.YC Delay S.DK.YC Delay S.I.YC Delay S.M.YC Delay S.L.YC Delay N.M.YC Delay N4.43 YC Delay Range 1 -1 --7 -9 -9 -7 --6

Dolby Prologic 4:3(Option) 200-channle ON OFF ON 2-TUNER ON ON OFF RCA+DVD ON ON OFF
Dolby Prologic 4:3(Option) 250-channle ON ON ON 2-TUNER ON ON OFF RCA+1SCART+DVD ON ON OFF
CRT CHANNEL X-LAY TTX AUTO FM PIP MULTI PIP LNA HIGH DEV SCART LETTER BOX DW PIP LIST PRIOR

TTX LANG

WEST EUROPE

ARABIC

AGC AV MEMORY AUSTRALIA CG BRIGHT
OFF/0N(Thailand) OFF OFF OFF

OFF OFF OFF OFF

1-2-2(G) YC DELAY
Item P.YC(AV) Delay S.YC(AV) Delay N.YC(AV) Delay P.BG.YC Dealy P.DK.YC Delay P.I.YC Delay P.M.YC Delay P.N.YC Delay S.BG.YC Delay S.DK.YC Delay S.I.YC Delay S.M.YC Delay S.L.YC Delay N.M.YC Delay N.443.YC Delay Range 1 -1 -2 -0 -7 -10 -9 -7 --1
1-3 Screen Change (When Adjusting I2C Bus Geometric Items)

V - S - CORRECTION

V SHIFT

H Parabolra

H Trapezium

H SHIFT

V LINEARITY

1-4 Other Adjustments

1-4-1 Screen Adjustment
1. Warm up the TV for at least 30 minutes. 2. Select the DYNAMIC Video mode. 3. Trun to the Video Mode(No Signal) using a remote-control. 4. Connect an oscilloscope to RK, GK, BK. 5. Press the Menu key to exit. 5. Adjust the VR (VR501, VR531, VR561) screen so that RK, GK, BK pulse is 20Vp-p each. (Turn the R,G,B VR screen fully counterclockwise in the area of each flyback line.) 3. Select Sub-Bright by pressing the Volume +/keys. 4. Adjust so that the 63 step on the right side of the screen is not seen (Use the Volume +/keys). keys in the following sequence : Displsy Menu Mute Power ON
1-4-4 High Voltage (29KV) Check

PRECAUTION

1. Input a lion head pattern.
1-4-2 White Balance Adjustment
2. Select DYNAMIC video mode. 1. Select the DYNAMIC video mode. 3. Warm up the TV for at least 10 minutes. 2. Input 100% white pattern. 4. Use a 1000:1 probe. 3. In the stand-by mode, press the remote-control keys in the following sequence: Displsy Menu Mute Power ON 4. Warm up the TV for at least 30 minutes. 5. Input a 10-step signal. 6. R-cut off, B-cut off, and G-cut off by pressing the Volume +/- keys. 7. Adjust the low light with viewing the dark side of the screen. 8. Select R-drive, G-drive and B-drive by pressing the Volume +/- keys. 9. Adjust the high light with viewing the light side of the screen. 10. If necessary, redo adjustments 6~9. 11. Press the Menu key to exit.

ADJUSTMENT

1. Connect the (+) terminal of the 10000:1 probe to the high voltage distributor and the(-) terminal to GND(located on the deflection board). 2. Adjust RR471S (located on the deflection board) so that the digital meter indicates DC290V 0.1V.
4-4-5 F.S. (Fail Safe) Circuit Check
Note : The finished product has a well-mounted VR(RR402S). If necessary, do the F.S adjustments in the following sequece. 1. Use a digital multimeter. 2. Connect the digital multimeter to the JIG pin (DZ482S) terminals. 3. Adjust VR(RR402S) so that the voltage becoms 2.25V. 4. After the adjustments are complete be sure to mount VR(RR402S) correctly.

1-4-3 Sub-Brightness Adjustment
1. Input a sub-brightness adjustment signal. (TOSHIBA PATTERN) 2. In the stand-by mode, press the remote-control
1-4-6 Static Focus Adjustment
1. Select the DYNAMIC video mode. 2. Input a crosshatch pattern. 3. Cover the lenses that are not being adjusted. 4. Connect a convergence jig and read data. 5. Adjust the lens for best focus. (See Fig, 4-1) 5. Green lens adjustment: Set the lens at the point where Blue just changes to Red. If the color aberration is irregular throughout the picture screen, adjust the lens to show Red color aberration (approximately 1~3 mm area) within a 3-block grid around the horizontal center-line. If the color aberration is irregular, adjust the lens as shown in the diagram below. (Accurate alignment of Green is important for overall color quality.) 6. Red lens adjustment Set the Red lens at the point where Orange becomes Crimson. 7. Blue lens adjustment Set the Blue lens at the point where Purple becomes Green.

P L1 L2

4. When the lens is turned clockwise, the color aberration will change as follows: Lens R G B Color Aberration Change Orange - Crimson Blue - Red Purple - Green

STATIC FOCUS (CONTINUED)

Vary the focus pack VR (Red, Blue) on the front cabinet. Adjust the TV for best possible focus around the center of the crosshatch pattern, without losing overall screen balance. Figure Crosshatch Pattern Examine these points together.
Examine these points together
Fig. 4-1 Crosshatch Pattern.
RED ABERRATION BLUE ABERRATION < L1, L2_ P
1-4-7 Lens Focus Adjustment

PRECAUTIONS

1. Do this adjustment after the static focus adjustment and the tilt adjustment. 2. Select the DYNAMIC video mode. (Contrast:100, Brightness:50) 3. Input a crosshatch pattern.
Fig. 4-2 Color Aberration
1. Loosen the lens screws. 2. Cover the two lenses that are not being adjusted. 3. Adjust the lens, observing the color aberration vertically and horizontally within 3 blocks of the center of the crosshatch pattern.

1-5 Beam alignment Adjustments
1. Select the DYNAMIC video mode. 2. Warm up the set at least for 10 minutes. 3. Enter the Convergence mode by pressing the remote control buttons in the following sequence :
4. Set the Beam Alignment Adjustment CY to Zero magnetic field area.
(Creation of CPM Zero Magnet)
(Creation of the 2-pole/4-pole zero magnets)
5. Check the squarewave at the point where the focus is misaligned. 6. Press the button on the remote control during 3~5 sec and vibrating dot-pattern appears. 7. Adjust the Focus-pack VR for defocusing. 8. Mute the other patterns (R/B) other than G-PATTERN. (Use

G-FOCUS

buttons on the remote control.)
Varying the 2-pole of VM (Varying G-Focus Pack) G-FOCUS CORE (Positioning the Core in the Center)
Varying the 4-pole of VM (When VM 2-Pole Adjustment is completed) (Adjust until the light around the core becomes a circle)
9. Adjust the 2, 4 polarities of VM-COIL as shown in figure below. 10. Adjust the G-Focus until any light around the core disappears. 11. Adjust G-Focus so that the surrounding flash can disappear from the spot. 12. After G-Focus adjustments are complete, adjust R-Focus as above procedures. 13. The B-CRT adjustments can be omitted because the variance of beam focus is small. (Only Vm-coil is mounted.) 14. Adjust the Focus-pack VR for fine focusing. 15. Press the mode. 16. Press the
button on the remote control, and the mode changes to the Convergence Adjustment button on the remote control to return to normal viewing.

1-6 High Voltage Part

1-6-1 PWM REG Circuit
For the existing high voltage REG circuit (input voltage variation type), a dynamic REG response is not provided. So it is difficult for both beam linearity and uniformity in screen size to be maintained on the screen with rapidly changing beams. A PWM (Pulse Width Modulation) type of high voltage, however, provides the maintenance of beam linearity and uniformity in screen size via a quick response to beam change by performing sync lock every 1H line, and detecting beam fluctuation at 1H line, and then controlling the IC current of high voltage output circuit. 1. High Voltage Fluctuation Detect (DC Detect) FBT pin 11 detects DC high voltage fluctuation. The detected DC high voltage value is input to PWM IC471 pin1 through R473, VR471, R471, and then it is input to a differential AMP circuit that differentiates the gap after comparing with the reference voltage input to pin2. 2. High Voltage Fluctuation Detect (AC Detect) 4. Dead Time (HV Protect) To check AC high voltage fluctuation, the output from FBT is detected by using a capacitor inside the high voltage distributor. The detection of AC high voltage fluctuation, a detection of dynamic beam current change is required in order to keep beam linearity and uniformity in size. Regarding the capacitor, a capacity of less than 3000P should be applied to a PWM type. (The existing type needs a capacity of about 6000P.) AC detect circuit eliminates unnecessary high frequency by using C476, D472. Also, AC gain is limited to + / - 0.7V (D472). This AC gain is combined with the detection value of DC high voltage fluctuation by using C478. Dead Time (PWM IN pin4) consists of C481, delays high voltage for a certain time to soft start in power on, a x-ray protection circuit. The voltage of Dead Time is detected by FBT pin7 and through DC Feedback. The normal voltage of Dead Time is +27V. When high voltage increases, however, detected voltage is in proportion to high voltage. Then, the detected voltage is applied to ICR01S(TL431). If the voltage is over 2.5V (normal:about 2.25V), TL431 turns ON, the base port of QR401S becomes low, and then an emitter current flows. At this time, a high voltage protection point is set. When QR401S turns ON, high voltage is applied to PWM IC pin4 and then muted. 3. PWM IC OSC Sync Lock A PWM type IC needs sync lock for PWM pulse and horizontal scan line. The standard time constant of OSC circuit is determined by C487, R475 (PWM IC pins 5 and 6). And the standard OSC frequency is about 27 kHz. The horizontal frequency of scan line is 31.5kHz(NT), 31.25kHz(PAL), so sync lock for this horizontal frequency should be performed using sync lock circuit. The sync lock circuit consists of Q481(Tr KSC815-Y), D479, D478, and C492. The input AFC signal is connected to PWM IC pin 5 through D479 so that it can be negative Trig.

PWM type When a Toshiba Pattern is recrived, the screen is displayed as shown in figute side Existing type

1-6 SCREEN-JIG

1-6-1 42W5
42W5 Screen Size : X 932, Y 524 (X:764 = 22 x 2 + 60 x 12, Y:262 = 17 x 2 + 38 x 6)-PAL MODE

2 6.m m 7 3.m m 2 6.m m

3 4.m m

7 6.m m

1-6-2 47W3
47W3 Screen Size : X 1045, Y 588 (X:764 = 22 x 2 + 60 x 12, Y:262 = 17 x 2 + 38 x 6)-PAL MODE

3 0.m m 8 2.m m 3 0.m m

3 8.m m

8 5.m m

1-6-3 55W3
55W3 Screen Size : X 1225, Y 686 (X:764 = 22 x 2 + 60 x 12, Y:262 = 17 x 2 + 38 x 6)-PAL MODE

3 5.m m 9 6.m m 3 5.m m

4 4.m m

9 9.m m

1-6-4 65W3
65W3 Screen Size : X 1442, Y 838 (X:764 = 22 x 2 + 60 x 12, Y:262 = 17 x 2 + 38 x 6)-PAL MODE

4 1.m m

5 4.m m

1-6-5 43T6/43T7

43T6 Screen Size : X 885, Y 666 (X:764 = 22 x 2 + 60 x 12, Y:262 = 17 x 2 + 38 x 6)-PAL MODE

2 5.m m 6 9.m m 2 5.m m

4 3.m m

9 6.m m

1-6-6 48T6
48T6 Screen Size : X 973.4 Y 738.4 (X:764 = 22 x 2 + 60 x 12, Y:262 = 17 x 2 + 38 x 6)-PAL MODE

2 8.m m

4 7.m m

1-6-7 54T6

54T6 Screen Size : X 1099 Y 823 (X:764 = 22 x 2 + 60 x 12, Y:262 = 17 x 2 + 38 x 6)-PAL MODE

3 1.m m 8 6.m m 3 1.m m

5 3.m m

1-6-8 62T6

62T6 Screen Size : X 1259.4, Y 948 (X:764 = 22 x 2 + 60 x 12, Y:262 = 17 x 2 + 38 x 6)-PAL MODE

3 6.m m 9 8.m m 3 6.m m

6 1.m m
1-7 Remote Control for Servicing(Convergence Mode)
Convergence Data LINE Adjust ENTIRE Adjust G-Mute R-Mute B-Mute Exit Button
Mute VOL P Still Surround S.STD P.STD
Last Data Save button/Canccel Cg Factory Data Select Key(Each Inch) R-Selete B-Selete G-Selete

TV S.Mode

Save Button
Convergence Data Left/Right Move Button
Convergence Data UP/DOWN Move Button

Test Normal

Display

P.Size

Text/Mix

Info. Scan

Sleep Perfect Focus Swap Locate
Convergence H-PHASE Move Button(Right)
Convergence H-PHASE Move Button(Left)

PIP ON

1-7-1 KEY Function
1. R-SELECT Press to select RED color. 2. G-SELECT Press to select GREEN color. 3. B-SELECT Press to select BLUE color.
4. R-MUTE Press to mute RED color. 5. G-MUTE Press to mute GREEN color.
TV 6. B-MUTE Press to mute BLUE color.
7. CANCEL KEY Press to revert to the previous data during the Convergence Adjustment. 8. TEST/NORMAL Press to check TV mode in the Convergence Mode. 9. LINE SHIFT Press to move a line up/down or left/right. 10. FACTORY DATA SELECT BUTTON Press to call the factory default values.

DYNAMIC FOCUS GND SERIAL CLOCK LINE1 CONVERGENCE SYNC GND N.C CONVERGENCE RED CONVERGENCE GREEN CONVERGENCE BLUE SERIAL DATA LINE1 N.C INPUT REMOCON N.C GND GND GND BLUE VERTICAL OUT BLUE HORIZONTAL OUT GREEN VERTICAL OUT GREEN HORIZONTAL OUT RED VERTICAL OUT RED HORIZONTAL OUT GND HORIZONTAL BLANK VERTICAL BLANK GND N.C -5[V] 5[V] GND

Schematic Diagrams

5. Schematic Diagrams

5-1 MAIN 1

5-2 MAIN 2

5-3 MAIN 3

TP06 TP07

5-4 MAIN 4

TP12 TP14 TP13 TP11 TP10 TP09 TP08
TP15 TP16 TP17 TP18 TP19 TP20

TP17 TP11 TP16 TP10

5-5 T_CM2906_002 MICOM

5-6 T_CMDEAC_XXX MICOM

5-7 CRT

5-8 SUB 1

5-9 SUB 2
5-10 CONVERGENCE ( SDC12 - 1 )
5-11 CONVERGENCE ( SDC12 - 2 )

5-12 PRO SCAN 1

5-13 PRO SCAN 2

5-14 AV FRONT

5-15 VM

5-16 CONTROL

5-17 DY JACK, SENSOR

DY JACK

SENSOR

5-18 CG AMP

5-19 SUB AMP

PCB Diagrams

4. PCB Diagrams

4-1 MAIN PCB

8-2 SUB PDB

Electrical Parts List

You can search for the updated part code through ITSELF web site. URL : http://itself.sec.samsung.co.kr

3. Electrical Parts List

3-1 SP43T7HF1X/BOB
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
BP91-00525A BP61-00079A AA91-00735B AA63-00076A AA61-00810B AA61-00809B AA61-00056B AA60-10011A AA60-00127B AA60-00126B AA60-00125B AA39-00018A AA33-00016A AA27-00278A AA26-30006F 0204-001148 0203-001303 0201-001030 AA61-00845A AA03-00200A AA67-00157A AA67-10008A AA67-00188A AA67-00147A
ASSY CPT-R;SP43T7HPX/XEF,J54A HOLDER-DY;,PJTV,T0.5,NYLON66 V2 ASSY-BRKT,CRT;DP,AA91-00722A,PROJ SPACER-LENS;FELT ,T1.0,GRAY,7CRT,PROJEC HOLDER-CAP;PROJ,PC,CLR HOLDER-CRT;PROJ,PC/ABS GF 20%,BLK BRACKET-LENS;PROJECTION,SECC,T1.6,-,-,-, SCREW-TAPTITE;-,SWRCH18A,M4,L12,HH,+,PC, SPACER-LENS;PROJ,SILICONE,D/GRAY SPACER-CAP;PROJ,EPDM,BLK SPACER-CRT;PROJ,SILICONE,D/GRAY LEAD CONNECTOR-ASSY;,UL1015#22,UL/CSA,1P MAGNET CONVERGENCE;JH 92LT - 29F,-,29.1M DEFLECTION YOKE;-,PT-S0712AC,S/S,PJTCRT( FLYBACK;*WIRE*-,FWZ-50A001C,55,30KV ETHYLENE GLYCOL;MS-S02,CH20HCH20H,80,20 TAPE-ACETATE;#1554,T0.25MM,W19MM,L30M,WH ADHESIVE-SIL;SE9178,GRY,NON-FLOW,UL94V0 CASE-COUPLER,R;DP,PROJ,AA61-00806B CRT MONO;P16LSG03RJA,-,7inch,-,-,-,FLAT LENS;,DELTA 240,RED,C-ELEMENT LENS;-,-,DELTA,77,RED,S4388,LENS;DELTA71,RED C ELEMENT LENS-ASSY;,DELTA 78,CLEAR A/B

AA33-00018A AA27-00278A AA26-30006F 0204-001148 0203-001303 0201-001030 AA61-00847A AA03-00202A AA67-00156A AA67-10007A AA67-00190A AA67-00147A
MAGNET CONVERGENCE;JH 92LT - 36F,-,29.1M DEFLECTION YOKE;-,PT-S0712AC,S/S,PJTCRT( FLYBACK;*WIRE*-,FWZ-50A001C,55,30KV ETHYLENE GLYCOL;MS-S02,CH20HCH20H,80,20 TAPE-ACETATE;#1554,T0.25MM,W19MM,L30M,WH ADHESIVE-SIL;SE9178,GRY,NON-FLOW,UL94V0 CASE-COUPLER,B;DP,PROJ,AA61-00808B CRT MONO;P16LSG03BMB,-,7inch,-,-,-,FLAT LENS;,DELTA 240,CLEAR,C-ELEMENT LENS;-,-,DELTA,77,CLEAR,S4388,LENS;DELTA71,CLEAR C ELEMENT LENS-ASSY;,DELTA 78,CLEAR A/B
BP91-00245M AA95-01841C BP94-00239A BP94-00328A BP94-00238A BP94-00353A BP94-00382A BP94-00383A BP94-00442B BP94-00329A
ASSY CHASSIS;SP43T7HFS,J54A,C2.0 ASSY SUB-PCB,SENSOR;DP,PCL545R,P54A,AA95 ASSY PCB MISC-DY-JACK;DP,HCM4215W3S/XAA, ASSY PCB MISC-CONTROL POWER;DP,SP43T7HPS ASSY PCB MISC-VM;DP,HCM4215W3S/XAA,P55A ASSY PCB MISC-A/V FRONT;DP, SP43T7HPS/XE ASSY PCB MISC-SUB AMP;DP,SP43T7HFS,J54A, ASSY PCB MISC-CG-AMP;DP,SP43T7HFS,J54A,C ASSY PCB MISC-SPK TERMINAL;DP, BP96-0003 ASSY PCB MISC-CONTROL SIDE;DP,SP43T7HPS/
BP91-00526A BP61-00079A AA91-00735B AA63-00076A AA61-00810B AA61-00809B AA61-00056B AA60-10011A AA60-00127B AA60-00126B AA60-00125B AA39-00018A AA27-00278A AA26-30006F 0204-001148 0203-001303 0201-001030 AA61-00846A AA03-00201A AA67-00158A AA67-10071A AA67-00189A AA67-00147A
ASSY CPT-G;SP43T7HPX/XEF,J54A HOLDER-DY;,PJTV,T0.5,NYLON66 V2 ASSY-BRKT,CRT;DP,AA91-00722A,PROJ SPACER-LENS;FELT ,T1.0,GRAY,7CRT,PROJEC HOLDER-CAP;PROJ,PC,CLR HOLDER-CRT;PROJ,PC/ABS GF 20%,BLK BRACKET-LENS;PROJECTION,SECC,T1.6,-,-,-, SCREW-TAPTITE;-,SWRCH18A,M4,L12,HH,+,PC, SPACER-LENS;PROJ,SILICONE,D/GRAY SPACER-CAP;PROJ,EPDM,BLK SPACER-CRT;PROJ,SILICONE,D/GRAY LEAD CONNECTOR-ASSY;,UL1015#22,UL/CSA,1P DEFLECTION YOKE;-,PT-S0712AC,S/S,PJTCRT( FLYBACK;*WIRE*-,FWZ-50A001C,55,30KV ETHYLENE GLYCOL;MS-S02,CH20HCH20H,80,20 TAPE-ACETATE;#1554,T0.25MM,W19MM,L30M,WH ADHESIVE-SIL;SE9178,GRY,NON-FLOW,UL94V0 CASE COUPLER G;DP,PROJ,AA61-00807B CRT MONO;P16LSG03HKA,-,7inch,-,-,-,FLAT LENS;,DELTA 240,GREEN,C-ELEMENT LENS;DELTA 77 79,-,GREEN,C ELEMENT, LENS;DELTA71,GREEN C ELEMENT LENS-ASSY;,DELTA 78,CLEAR A/B
BP94-00257A AA59-00171A AA39-20577B AA40-00051A AA40-00050A AA96-20130A AA39-30007A AA39-00006A

3-2 SP48T7HF1X/BOB

Loc. No. Code No. BP91-00525A BP61-00079A AA91-00735B AA63-00076A AA61-00810B AA61-00809B AA61-00056B AA60-10011A AA60-00127B AA60-00126B AA60-00125B AA39-00018A AA33-00016A AA27-00278A AA26-30006F 0204-001148 0203-001303 0201-001030 AA61-00845A AA03-00200A AA67-00157A AA67-10008A AA67-00188A AA67-00147A Description ; Specification Remark Loc. No. 2 Code No. AA03-00202A AA67-00156A AA67-10007A AA67-00190A AA67-00147A Description ; Specification CRT MONO;P16LSG03BMB,-,7inch,-,-,-,FLAT LENS;,DELTA 240,CLEAR,C-ELEMENT LENS;-,-,DELTA,77,CLEAR,S4388,LENS;DELTA71,CLEAR C ELEMENT LENS-ASSY;,DELTA 78,CLEAR A/B Remark
BP91-00527A BP61-00079A AA91-00735B AA63-00076A AA61-00810B AA61-00809B AA61-00056B AA60-10011A AA60-00127B AA60-00126B AA60-00125B AA39-00018A AA33-00018A AA27-00278A AA26-30006F 0204-001148 0203-001303 0201-001030 AA61-00847A
ASSY CPT-B;SP43T7HPX/XEF,J54A HOLDER-DY;,PJTV,T0.5,NYLON66 V2 ASSY-BRKT,CRT;DP,AA91-00722A,PROJ SPACER-LENS;FELT ,T1.0,GRAY,7CRT,PROJEC HOLDER-CAP;PROJ,PC,CLR HOLDER-CRT;PROJ,PC/ABS GF 20%,BLK BRACKET-LENS;PROJECTION,SECC,T1.6,-,-,-, SCREW-TAPTITE;-,SWRCH18A,M4,L12,HH,+,PC, SPACER-LENS;PROJ,SILICONE,D/GRAY SPACER-CAP;PROJ,EPDM,BLK SPACER-CRT;PROJ,SILICONE,D/GRAY LEAD CONNECTOR-ASSY;,UL1015#22,UL/CSA,1P MAGNET CONVERGENCE;JH 92LT - 36F,-,29.1M DEFLECTION YOKE;-,PT-S0712AC,S/S,PJTCRT( FLYBACK;*WIRE*-,FWZ-50A001C,55,30KV ETHYLENE GLYCOL;MS-S02,CH20HCH20H,80,20 TAPE-ACETATE;#1554,T0.25MM,W19MM,L30M,WH ADHESIVE-SIL;SE9178,GRY,NON-FLOW,UL94V0 CASE-COUPLER,B;DP,PROJ,AA61-00808B
BP64-00017B BP64-00016A BP64-00015B AA67-00195A AA67-00115B AA67-00129A BP61-00016A BP61-00017A BP61-00012A AA60-00072C AA63-60122J BP73-00004A
CABINET-BACK,BOT;DP,43T7,AA64-02735B CABINET-BACK,TOP;DP,43T7,AA64-02734A CABINET-FRONT,BOT;DP,43T7 EUR,AA64-02732 SCREEN-TINT;43,908*690,T=0.73,P=0.52 SCREEN-FRESNEL;43N,-,T2,910*692,-,-,SUN SCREEN-AG;43J8,T=82%,910*692*2,G=110 BRACKET-SCREEN,TB;DP,43T7,AA61-01124A BRACKET-SCREEN,RL;DP,43T7,AA61-01125A BRACKET-MIRROR;DP,42W5,AA61-01123A,11.8K SPACER-COVER,DUST;43T7,SPONGE 94HF-1,T3. SPACER-FELT;SPD-50P3H,FELT,L530,D20,T0.3 RUBBER-CAP;42W5,SILICONE,WHT,RUBBER
AA67-00205D AA26-00101A BP39-00009A BP39-00036A BP39-00048A AA61-00049B BP61-00043B BP61-00052A AA64-60449B BP64-00044A AA65-30018A AA65-30105A AA65-00020A AA65-30008A AA65-30013A AA65-30111A AA63-10002A AA63-10007B AA63-10002A 6003-001023 6003-001026 AA60-10011A 6005-001003 6005-001004 6009-001296 6002-000522 BP69-00020A BP69-00021A AA69-01652A BP59-00008A BP68-00099A AA68-50509A AA68-00526A AA68-00340A AA68-00344A AC68-00347A AA68-00345A AC68-00285A AA68-01070A AA68-50523A AA68-02415A 0203-000402 AA02-00022A 0203-001329 0201-001059 AA69-00862A AA69-00744L 4301-000120 AA63-70002B

MIRROR-BACK;DP,43T7,SSM,795*569*554*(78) TRANS FBT;FWZ50A001E/FFA97513B,12KV,5P,LEAD CONNECTOR ASSY;P54A/SVP-42W5,UL2547 LEAD CONNECTOR;J54A/SP42W5HP,UL2547#26,U LEAD CONNECTOR;P55A/SVP-47W3HRT,UL1617#2 HOLDER-BOX;-,PP,-,-,-,NTR,V0,AA61-20285A HOLDER-SENSOR;W9,PC HB,VIOLET HOLDER-WIRE;PJTV,NYLON,66,NATURAL INLAY-COVER;SP-434JMF,PS,T0.5,149.3X69.5 INLAY-VENT;43T7,PS SHEET,T0.5 CLAMP-WIRE;DONG-A,NYLON-66,-,-,-,DATL-60 CLAMPER CORE-WIRE;ALL MODEL,NYLON 66,V2, CLAMP CORE-WIRE;55W9,NYLON 66 CLAMP-CORD;-,PE,HB,-,BLK,CLAMP-WIRE;-,NYLON-6 CLAMP-WIRE;ALL MODEL,NYLON,V0,-,WHT,1T 1 BAND-TIE;-,NYLON66 V2,-,-,L100,NTR,BAND-PP;W18,CLEA BAND-TIE;-,NYLON66 V2,-,-,L100,NTR,SCREW-TAPTITE;RWH,+,B,M3,L10,ZPC(YEL),SW SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK) SCREW-TAPTITE;-,SWRCH18A,M4,L12,HH,+,PC, SCREW-WOOD;HH,+,M4,L19,ZPC(BLK),SWRCH18A SCREW-WOOD;HH,+,M4,L27,BLK,SWRCH18A SCREW-SPECIAL;BH,+,-,M4,L12(11),ZPC(BLK) SCREW-TAPPING;TH,+,2,M4,L15,ZPC(BLK),SWR PACKING CASE-OUT;43T7,H-3 YEL,C3,1045,63 PACKING-COVER,BOT;43T7,H-3 AB,C3,YEL,965 CUSHION-SET;43T7,PS FOAMED,C=0.02 REMOCON;,TM65A,COMMOANDO,J54A,49,L/GRAY, MANUAL USERS;SP43T7HF,GE,W/100G,J54A,B5, LABEL-BOX;A/P 90(G),ALL MODEL,-,WHT,L250 LABEL-RATING;ART PAPER(90),ALL MODEL,LAM LABEL-WARRANTY;-,-,-,WHT,75MM,20 LABEL-TRANSFER BOX;-,TF-53B LABEL-TRANSFER RATING;ALTA RESISTENCI LABEL-TRANSFER WARRANTY;-,TF-53B5D LABEL-TAPE TRANSPARENT;SESA,A/P,T0.3, LABEL-MODEL;-,A/P,-,30,20,-,-,-,ALL MODE LABEL-BACK,DOLBY;A/P 100(G),CW764AHD,DOL CARD-RTF;COLORIT 54 CREMA,MOJO80G,SPA,A TAPE-KRAFT;KRAFT,T0.17,W18,L50,BLK TAPE ETC;SESA,T0.3,75,132,BLK TAPE-OPP MASKING;ANT-300P,T0.07,W15.0,L5 ADHESIVE-SIL;#9590,WHT,-,CARTRIGE BAG PE;-,HDPE PE FOAM,T0.03,W400,H240 BAG-SHEET;-,HDPE PE FOAM,T0.015,W1650,H1 BATTERY-MN;1.5V,-,AA,14.5x50mm,SHEET;,PE-FOAM,T1.0,50G

3-3 SP42W5HFX/XEU

Loc. No. Code No. AA91-04077A AA91-04078A AA91-04079A AA91-04093A AA94-08401A AA94-08448A AA94-08457A AA94-08458A AA95-01841C AA94-11168E AA59-00171A AA96-20130G Description ; Specification Remark Loc. No. 1 Code No. AA39-30007B AA67-00204C BP61-00012A BP61-00010A BP61-00011A AA67-00193A AA67-00193B AA67-00207A BP39-00009A AA39-00285A BP65-00001B AA26-00101A AA61-00049B BP61-00043B AA64-60449B BP64-00029A AA65-30013A AA65-30018A AA65-30104B AA65-30008A BP61-00052A 6003-001019 6003-001022 6003-001026 AA60-10011A 6005-001003 6003-001339 AA63-70002B 0201-001059 0203-001329 AA60-00072B BP73-00004A AA69-01678A BP69-00019D AA69-01651A AA59-00220A AA68-01778A 6801-001014 AA39-40001B 4301-000115 AA68-50523A AA68-50509A AA68-00344A AA68-00526A AC68-00347A AA68-00340A AA68-00345A AA69-00862A AA69-00744L AA63-10002A AA63-10002A 0203-000402 AA68-02415A AA02-00022A AA65-00020A AA69-01876A AA39-20577B AC68-00285A AA63-10007B Description ; Specification Remark

ASSY CPT-R;,P16LSG03RJA,42,VENUS,D7 ASSY CPT-G;,P16LSG03HKA,42,VENUS,D7 ASSY CPT-B;,P16LSG03BMB,42,VENUS,D7 ASSY CHASSIS;SP42W5HFX/XEF,J52A ASSY PCB CRT;SP42W5HFX/XEF,J52A,DP ASSY PCB MISC-A/V FRONT;SP42W5HFS/XEF,J5 ASSY PCB MISC-A/V TERMINAL;SP42W5HFS/XEF ASSY PCB MISC-SUB-AMP;SP42W5HFS/XEF,J52A ASSY SUB-PCB,SENSOR;DP,PCL545R,P54A,AA95 ASSY PCB MISC-V/M;PCL5415R3S/XAA,P54A, MODULE-FOCUS,PACK;SVP-5200,S300-P3,-,-,ASSY POWER CORD;,CP2/NO(4.0R),H/C 2
BP91-00005C AA64-02724A AA61-00616B AA61-00097A BP61-00075A AA61-00094C BP61-00019A AA61-00533B 3001-001107 3001-000279 AA98-00049A 3301-001201 AA39-00086A AA60-10051A AA61-00864A BP61-00035A AA61-00617B 6006-001094 AA61-00618C
ASSY CABINET WOOD; WOOD,EUP,42W5 CABINET-WOOD;42W5,WOOD,SDE8336R HOLDER-CRT,MAIN;54J7,DP,-,-,-,-,AA61-005 HOLDER-WIRE;-,NYLON 6/6,-,-,-,NTR,HOLDER-JERSEY,ASSY;W3,ABS V0,GRAY,63-000 HOLDER-RAIL;PCJ533R,ABS,-,-,-,BLK,HB,480 HOLDER-PALLET;42W5,HIPS HB,BLK BRACKET-GRILLE;43,54,62J8,SECC-1 ,T0.5,SPEAKER;20W,8ohm,95dB,1300Hz SPEAKER;30W,8OHM,91DB,20HZ ASSY-LEAD,CON;-,LEAD-CON,CORE,AA39-20505 CORE-FERRITE;AE,21x11x32mm,1500,280G LEAD CONNECTOR-ASSY;,2.2UF,REC,REC,200MM SCREW-WOOD;-,SWRCH18A,M4,L16,PH,+,-,-,ZP HOLDER-PCB;W3,HIPS,V0,BLK BRACKET-GRILLE;42W5,SECC-1,T1.0 BRACKET-CRT,MAIN;DP,54J7,AA61-00475B SCREW-ASSY WOOD;WW,HH,+,M7,L32,ZPC(YEL) GUIDE-FLOW;54J8,J7,ABS,IVORY,V0
BP96-00013A AA64-02727C AA61-01133A AA64-02211E 6003-001019
ASSY COVER P-C/FRONT,MASK;DP,42W5,HIPS H CABINET-FRONT,MASK TOP;42W5,HIPS,HB,G430 VELCRO-B;COMMANDO,BST1 1/4H BADGE-BRAND;72MM,AL FORGING,SVM1132,SAMS SCREW-TAPTITE;RH,+,B,M4,L12,ZPC(BLK),SWR
BP96-00014A AA64-02725A AA64-02743A BP73-00001A AA61-01132A 6003-001019
ASSY C/FRONT BOTTOM; DP,42W5,HIPS HB CABINET-FRONT,BOT;42W5,HIPS,HB,G4309,SVM BADGE-DECORATION;42W5,AL,NI RUBBER-SHEET;42W5,NBB RUBBER,GRAY,10*20 VELCRO-A;COMMANDO,BST1 1/4H SCREW-TAPTITE;RH,+,B,M4,L12,ZPC(BLK),SWR
AA96-01135A BP64-00013A AA64-02740A AA61-60003J AA64-02742A BP64-00011A AA61-01130A AA94-08320A AA61-20129A AA61-01132A AA61-01133A 6003-001019 6003-001023 BP64-00035F
ASSY COVER P;42W5 CABINET-FRONT,PANEL CONTROL;DP,42W5,AA64 KNOB-POWER;42W5,ABS,HB,G3676,COT SPRING-CS;-,SUS304,-,-,OD6, WINDOW-RMC,LED;42W5,PC,CLR KNOB-CONTROL;DP,42W5,AA64-02739A 10.5KG GUIDE-KNOB,CONTROL;42W5,ABS HB,G3676,SVM ASSY PCB MISC-CONTROL;SP42W5HFS/XEF,J52A HOLDER-WIRE;-,NYLON-66,-,-,-,NTR,DAFC-25 VELCRO-A;COMMANDO,BST1 1/4H VELCRO-B;COMMANDO,BST1 1/4H SCREW-TAPTITE;RH,+,B,M4,L12,ZPC(BLK),SWR SCREW-TAPTITE;RWH,+,B,M3,L10,ZPC(YEL),SW INLAY-DECORATION;42W5,AL,T0.4,SESA 1POLE

BP96-00014A AA64-02725A AA64-02743A BP73-00001A AA61-01132A 6003-001019 BP98-00088H 6003-001019 AA61-01133A AA64-02727Q AA64-02211E
ASSY C/FRONT BOTTOM; DP,42W5,HIPS HB CABINET-FRONT,BOT;42W5,HIPS,HB,G4309,SVM BADGE-DECORATION;42W5,AL,NI RUBBER-SHEET;42W5,NBB RUBBER,GRAY,10*20 VELCRO-A;COMMANDO,BST1 1/4H SCREW-TAPTITE;RH,+,B,M4,L12,ZPC(BLK),SWR ASSY C/FRONT,MASK;SP42W5HF1S/XEF,J54 SCREW-TAPTITE;RH,+,B,M4,L12,ZPC(BLK),SWR VELCRO-B;COMMANDO,BST1 1/4H CABINET-FRONT,MASK TOP;42W5,HIPS,HB,G430 BADGE-BRAND;72MM,AL FORGING,SVM1132,SAMS
BP91-00455A BP61-00079A AA91-00735B AA63-00076A AA61-00810B BP61-00091A AA61-00056B AA60-10011A AA60-00127B AA60-00126B AA60-00128B AA39-00018A AA33-00018A AA27-00278A AA26-30006F 0204-001148 0203-001303 0201-001030
ASSY CPT-B;SP42W5HPX/XEU,J54A,CRT-B ASSY HOLDER-DY;,PJTV,T0.5,NYLON66 V2 ASSY-BRKT,CRT;DP,AA91-00722A,PROJ SPACER-LENS;FELT ,T1.0,GRAY,7CRT,PROJEC HOLDER-CAP;PROJ,PC,CLR HOLDER-CRT;PJTV,PCABS GF20%,BLK BRACKET-LENS;PROJECTION,SECC,T1.6,-,-,-, SCREW-TAPTITE;-,SWRCH18A,M4,L12,HH,+,PC, SPACER-LENS;PROJ,SILICONE,D/GRAY SPACER-CAP;PROJ,EPDM,BLK SPACER-CRT;PROJ(65),SILICONE,D/GRAY LEAD CONNECTOR-ASSY;,UL1015#22,UL/CSA,1P MAGNET CONVERGENCE;JH 92LT - 36F,-,29.1M DEFLECTION YOKE;-,PT-S0712AC,S/S,PJTCRT( FLYBACK;*WIRE*-,FWZ-50A001C,55,30KV ETHYLENE GLYCOL;MS-S02,CH20HCH20H,80,20 TAPE-ACETATE;#1554,T0.25MM,W19MM,L30M,WH ADHESIVE-SIL;SE9178,GRY,NON-FLOW,UL94V0
BP91-00005F AA60-10051A AA61-00094C AA61-00097A AA61-00508D AA61-00533B AA61-00616B AA61-00864A AA64-02724A BP61-00019A BP61-00035A AA61-10247A AA60-10051B 3001-000279 3001-001107 AA39-00086A AA98-00049B AA61-00617B 6006-001094 AA61-00618C
ASSY-CABINET,WOOD;,WOOD,42W5, DO SCREW-WOOD;-,SWRCH18A,M4,L16,PH,+,-,-,ZP HOLDER-RAIL;PCJ533R,ABS,-,-,-,BLK,HB,480 HOLDER-WIRE;-,NYLON 6/6,-,-,-,NTR,HOLDER-JERSEY;W3,ABS V0,GRAY,G4309 BRACKET-GRILLE;43,54,62J8,SECC-1 ,T0.5,HOLDER-CRT,MAIN;54J7,DP,-,-,-,-,AA61-005 HOLDER-PCB;W3,HIPS,V0,BLK CABINET-WOOD;42W5,WOOD,SDE8336R HOLDER-PALLET;42W5,HIPS HB,BLK BRACKET-GRILLE;42W5,SECC-1,T1.0 BRACKET-FOCUS;S46DS,SECC,T1.0,-,-,-,SCREW-WOOD;-,SWRCH18A,M3.5,L11,RH,+,-,-, SPEAKER;30W,8OHM,91DB,20HZ SPEAKER;20W,8ohm,95dB,1300Hz LEAD CONNECTOR-ASSY;,2.2UF,REC,REC,200MM ASSY-LEAD,CON;-,LEAD-CON,CORE,AA39-20505 BRACKET-CRT,MAIN;DP,54J7,AA61-00475B SCREW-ASSY WOOD;WW,HH,+,M7,L32,ZPC(YEL) GUIDE-FLOW;54J8,J7,ABS,IVORY,V0

BP98-00090D BP64-00013A AA64-02740A AA61-60003J AA64-02742A BP64-00011A AA61-01130A
ASSY PANEL CONTROL;SP42W5HPS/XEU,P5 CABINET-FRONT,PANEL CONTROL;DP,42W5,AA64 KNOB-POWER;42W5,ABS,HB,G3676,COT SPRING-CS;-,SUS304,-,-,OD6, WINDOW-RMC,LED;42W5,PC,CLR KNOB-CONTROL;DP,42W5,AA64-02739A 10.5KG GUIDE-KNOB,CONTROL;42W5,ABS HB,G3676,SVM
BP94-00194A AA61-20129A AA61-01132A AA61-01133A 6003-001019 6003-001023 BP64-00035J
ASSY PCB MISC-CONTROL;DP,SP42W5HPS/XEU,J HOLDER-WIRE;-,NYLON-66,-,-,-,NTR,DAFC-25 VELCRO-A;COMMANDO,BST1 1/4H VELCRO-B;COMMANDO,BST1 1/4H SCREW-TAPTITE;RH,+,B,M4,L12,ZPC(BLK),SWR SCREW-TAPTITE;RWH,+,B,M3,L10,ZPC(YEL),SW INLAY-DECORATION;42W5,AL,T0.4,PAL(COMAND
AA26-00101A AA67-00204C BP61-00012A BP61-00010A BP61-00011A AA60-00072B AA67-00193A AA67-00193B AA67-00207A BP61-00043B BP61-00052A AA61-00049B BP64-00029A AA64-60449B BP73-00004A AA63-10002A AA65-30013A AA65-30018A AA65-00020A AA65-30105A AA65-30111A AA65-30008A 6005-001003 6003-001026 6003-001023 6005-001003 6003-001339 AA60-10011A AA96-20130A AA39-30007A BP39-00036A BP39-00048A BP39-00009A AA39-00006A AA63-70002B AA69-01678A BP69-00019D AA69-01651A BP59-00008A BP68-00088A 0201-001059 0203-000402 AA02-00022A 0203-001329 AC68-00285A AA68-50523A AA68-00526A AC68-00347A AA68-50509A AA68-00344A AA68-00340A AA68-00345A AA69-00862A AA69-00744L 6801-001015 AA68-02415A AA69-01876A 4301-000120 AA63-10007B
TRANS FBT;FWZ50A001E/FFA97513B,12KV,5P,MIRROR-FRONT;DP,42W5,FSM,870*633*446 BRACKET-MIRROR;DP,42W5,AA61-01123A,11.8K BRACKET-SCREEN,TB;DP,42W5,AA61-01121A,26 BRACKET-SCREEN,RL;DP,42W5,AA61-01122A,13 SPACER-COVER,DUST;43,54,62J9,SPONGE 94HF SCREEN-TINT;42W,958*550,T=0.73,P=052 SCREEN-FRESNEL;42W,960*552,T=2.0 SCREEN-FILTER;,T=82%,960*552*2,G=110,AG HOLDER-SENSOR;W9,PC HB,VIOLET HOLDER-WIRE;PJTV,NYLON,66,NATURAL HOLDER-BOX;-,PP,-,-,-,NTR,V0,AA61-20285A INLAY-SUPPORT;42W5,PS SHEET,T0.5,94V0 INLAY-COVER;SP-434JMF,PS,T0.5,149.3X69.5 RUBBER-CAP;42W5,SILICONE,WHT,RUBBER BAND-TIE;-,NYLON66 V2,-,-,L100,NTR,CLAMP-WIRE;-,NYLON-6 CLAMP-WIRE;DONG-A,NYLON-66,-,-,-,DATL-60 CLAMP CORE-WIRE;55W9,NYLON 66 CLAMPER CORE-WIRE;ALL MODEL,NYLON 66,V2, CLAMP-WIRE;ALL MODEL,NYLON,V0,-,WHT,1T 1 CLAMP-CORD;-,PE,HB,-,BLK,SCREW-WOOD;HH,+,M4,L19,ZPC(BLK),SWRCH18A SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK) SCREW-TAPTITE;RWH,+,B,M3,L10,ZPC(YEL),SW SCREW-WOOD;HH,+,M4,L19,ZPC(BLK),SWRCH18A SCREW-TAPTITE;HH,+,B,M4,L15,ZPC(BLK),SWR SCREW-TAPTITE;-,SWRCH18A,M4,L12,HH,+,PC, ASSY-POWER,CORD;-,CP2/NO(4.0R),H/C150,KJ IF-CABLE;-,T,100mm,1365#26 LEAD CONNECTOR;J54A/SP42W5HP,UL2547#26,U LEAD CONNECTOR;P55A/SVP-47W3HRT,UL1617#2 LEAD CONNECTOR ASSY;P54A/SVP-42W5,UL2547 CABLE-RCA;-,RCA,3000MM,0.12/10,RED/WHT/Y SHEET;,PE-FOAM,T1.0,50G PACKING-COVER,BOT;42W5,H-3 AB,C3,YEL,910 PACKING CASE-OUT;42W4,H-3 YEL,C3,SESA CUSHION-SET;42W5,PS FOAMED,C=0.02 REMOCON;,TM65A,COMMOANDO,J54A,49,L/GRAY, MANUAL USERS;W3,ITA,W/P100(G),1,B5,J52A, ADHESIVE-SIL;#9590,WHT,-,CARTRIGE TAPE-KRAFT;KRAFT,T0.17,W18,L50,BLK TAPE ETC;SESA,T0.3,75,132,BLK TAPE-OPP MASKING;ANT-300P,T0.07,W15.0,L5 LABEL-TAPE TRANSPARENT;SESA,A/P,T0.3, LABEL-BACK,DOLBY;A/P 100(G),CW764AHD,DOL LABEL-RATING;ART PAPER(90),ALL MODEL,LAM LABEL-TRANSFER RATING;ALTA RESISTENCI LABEL-BOX;A/P 90(G),ALL MODEL,-,WHT,L250 LABEL-TRANSFER BOX;-,TF-53B LABEL-WARRANTY;-,-,-,WHT,75MM,20 LABEL-TRANSFER WARRANTY;-,TF-53B5D BAG PE;-,HDPE PE FOAM,T0.03,W400,H240 BAG-SHEET;-,HDPE PE FOAM,T0.015,W1650,H1 CARD REGISTRATION;XEG,GERMAN,MOJO100 CARD-RTF;COLORIT 54 CREMA,MOJO80G,SPA,A PALLET;ALL MODEL,WOOD,600,1200,120 BATTERY-MN;1.5V,-,AA,14.5x50mm,BAND-PP;W18,CLEA