WASHING MACHINE
SWV-1200F/1100F/1000F/800F P1291/P1091/P8091/P6091

SERVICE

Manual

CONTENTS

1. SPECIFICATIONS 2. OVERVIEW OF THE WASHING MACHINE 3. OVERVIEW OF THE CONTROL PANEL 4. PROCESS TABLE 5. GENERAL REEOR FUNCTION 6. TROUBLE DIAGNOSIS 7. TEST MODE 8. DESIGNATION OF MAIN COMPONENTS 9. PCB SHEMATIC DIAGRAM PCB CIRCUIT DIAGRAM PCB PATTERN DIAGRAM WIRING DIAGRAM 10.ASSEMBLE AND DISASSEMBLE 11.TOOLS FOR DISASSEMBLY AND ASSEMLY 12.EXPOLDED VIEW AND PARTS LIST
! Caution for the safety during servicing
1. Do not allow the customer to repair the product. The person may be injured or the product life may be shortened. 2. Execute A/S after unplugging the power supply unit. Be care of the electric shock. 3. Do not plug several plugs in the same outlet. It may cause the fire due to overheat. 4. Check the damage, pressing or burning of the power plug or outlet. Replace it promptly if it has problem.(It may cause the electric shock or fire) 5. Do not clean the main body with the water. It may cause the electric shock and fire and shorten the product life) 6. The wiring of the harness shall be free from the moisture and tightened during serving. It shall not be deviated by certain impact. 7. Remove any dust or filth on the housing section,wiring section,connection section during servicing. Protect the cause of the fire such as the tracking,shortage and etc. 8. Check any mark of the moisture on the electrical parts, harness section and etc. Replace the parts or remove the moisture. 9. Check the assembly status of the parts after servicing. Maintain the status before servicing. 10. Pull out the power cord with holding the plug. Be care of the electric shock and fire when the cord is damaged. 11. Unplug the power plug from the outlet when the wash machine is not used. Be care of the electric shock and fire due to the strike of the lightening. 12. Do not use or store the spray or flammable materials(including gasoline,alcohol and etc.) around the wash machine. Be care of the explosion or fire due to the electric spark. 13. Do not put the bowl of water or wet laundry on the wash machine. If the water is penetrated to the wash machine, this may cause the electric shock or fire. 14. Do not install the wash machine in the place where the snow or rain falls. It may cause the electric shock and fire and shorten the product life. 15. Do not push the control buttons with the awl,pin, or sharp materials. It may the electric shock and trouble. 16. Check the wash machine is leveled horizontally and installed properly on the floor. The vibration may shorten the product life. 17. Joint the wire by the connector correctly. When the wire is jointed by the tape, this may cause the fire due to the tracking. 18. When the wash machine is to be laid for the service, put the pad on the floor and lay the product at side slowly. If the wash machine is laid front, the relay may be damaged by the tub. 19. When the wash-heater is replaced, check it is inserted in the bracket-heater and screw the nut. If the wash-heater is not inserted in the bracket-heater properly, this may cause the noise and leakage since it is contacted to the drum.

SAMSUNG ELECTRONICS CO., LTD

1. Specifications

WASH TYPE DIMENSION GROSS NET WATER PRESSURE WEIGHT GROSS NET WASHand SPIN CAPACITY POWER CONSUMPTION WASHING FRONT LOADING TYPE W 669mm X D 656mm X H 910mm W 598mm X D 550mm X H 844mm 50 kPa ~ 800 kPa 80 kg 75 kg 5.0 kg (DRY LAUNDRY) 220 V 240 V WASHING and HEATING MODEL SPIN 220 V 240 V PUMPING WATER CONSUMPTION SPIN REVOLUTION MODEL rpm PPW 380 W 220 V 240 V 180 W 180 W 2000 W 2400 W
SWV-800F/P8091 SWV-1000F/P1091 SWV-1100F SWV-1200F/PW 430 W 500 W 500 W 34 W 54l(STANDARD COURSE) SWV-800F/P8091 SWV-1000F/P1091 SWV-1100F SWV-1200F/PW 550 W 550 W 550 W
2. Overview of the Washing Machine
CONTROL-PANEL ASSY DOOR DRAWER

WATER SUPPLY VALVE

SENSOR PRESSURE
ADJUSTABLE LEG ASSY PUMP HOSE DRAIN(OPTION) CAP DRAIN(OPTION)
POWER CORD BUFFER SPRING WEIGHT-BALANCE

DRAIN HOSE

PULLEY BELT ASSY MOTOR SHOCK ABSORBER
3. Overview of the control panel
SWV-1200F/1100F/1000F, P1291/1091

SWV-800F/P8091

1. Detergent dispenser 2. Display panel Displays the remaining wash cycle time, error messages and cancel. 3. Temperature selection button Press the button repeatedly to cycle through the available water temperature options (cold water, 30C, 40C, 60C and 95C). 4. Spin selection button Press the button repeatedly to cycle through the available spin speed options SWV-1200F/P1291 : (No spin, Rinse hold, 400, 600, 800, 1000and 1200rpms), SWV-1100F : (No spin, Rinse hold, 400, 600, 800, 1000and 1100rpms), SWV-1000F/P1091 : (No spin, Rinse hold, 400, 600, 800, and 1000rpms), 5. Delay Start button(OPTION) Press the button repeatedly to cycle through the available delayed start options (from 1 hour to 24 hours in one hour increments).
6. Course button Press the button repeatedly to select available wash programs 7. Manual button Press the button repeatedly to cycle through the available partial wash options [Wash+Rinse+Spin Prewash+Wash+SpinSpinRinse(1 time)+Spin Rinse(2 times)+SpinRinse(3 times)+Spin] in case P6091 [Wash+Rinse+Spin Prewash+Wash+SpinSpinRinse(3 times)+Spin] Note : Prewash is only available when washing cotton, synthetic or delicate. 8. Start/Pause button Press to pause and restart programs. 9. Door Open button(OPTION) Press to open the washing machine door. 10. O (On/Off) button Press once to turn the washing machine on, press again to turn the washing machine off. If the washing machine power is left on for longer than 10minutes without any buttons being touched, the power automatically turns off. 11. No Spin button(OPTION) Press to no spin program. 12. Rinse Hold button(OPTION) Press to rinse hold program.

5. General Error Function
When an error occurs, this function starts to keep generating error melody sounds and displays error indicators as shown in the followings per corresponding error by blinking in 0.5sec interval until the error status is completely cleared out. In this case, all the driving devices are turned off until the error is cleared out. 1. WATER SUPPLY ERROR - Water Supply Error occurs when water level frequency does not show changes more than 50Hz or water is not supplied up to the water level presetting for 20 min or more at the time of initial water supply, the error status can be cleared by turning POWER S/W OFF and resuming the POWER ON initial status. - Display shows E1. 2. WATER DRAIN ERROR - In case the water level frequency is 25.3KHz or less in the initial phase of UNB-detecting cycle. - Water Drain error can be cleared by turning POWER S/W OFF and resuming the POWER ON initial status. - Display shows E2. 3. OVER-FLOW ERROR - Over-Flow error occurs when the water level is in abnormal operation (OVER-FLOW: 22.40KHz/50 or more). It can be cleared by turning POWER S/W OFF. Water is drained prior to POWER S/W OFF and it is forced to be drained for 2 min if a frequency of more than 25.24 KHz is detected. - Display shows E3. 4. DOOR OPEN ERROR - Door Open error can be cleared by closing the door. - Display shows dE. 5. UNBALANCE ERROR - Unbalance error is cleared by POWER S/W OFF and by resuming the POWER ON initial status. - Display shows E4. 6. WATER HEATER ERROR - In case the water temperature varies by 40C or more in 5 min, or by 2C or less in 10 min after heating is started. - It can be cleared by turning POWER S/W OFF. - Display shows E5,E6. 7. ASSY PRESSURE S/W ERROR * Generated Frequency Signal of WATER LEVEL(W/L) S/W (KHz) Lvevl Abnormal W/L Frequency Low Level 30.00 KHz High Level 15.00 KHz
- If the same signal as the above table is detected for more than 5 seconds, it is a PRESSURE S/W Error. - When the error occurs, perform the time-drain for 3 min and then turn off the water drain pump. Then the display shows E7 as a pressure s/w error indicator. 8. ABNORMAL WATER TEMPERATURE ERROR Course Synthetic Delicate Wool Water Temp 60C or more 45C or more 45C or more
- In case the water temperature is 60C or more in the synthetic course, 50C or more in the delicate course, and 40C or more in the wool course. - At the time of initial water supply, if the water temperature is not appropriate, water starts to be drained and it is forced to be drained for 2 min when the abnormal frequency of 25.24KHz is detected. - Display shows E8. - This error can be cleared by POWER S/W OFF. SAMSUNG ELECTRONICS CO., LTD 7

10. Assemble and Disassemble
1. ASSY-COVER TOP 1) Remove two screws fixing the top-cover on back side. 2) Push the top-cover back about 15mm and pull it up. 3) Its possible to exchange and service the trans former, the pressure-senser, the noise-filter and the water valve.
2. FRAME FRONT 1) Remove the top-cover and the assy drawer. 2) Remove two screws fixing the control-panel on front side and the screw on right side. 3) Remove the cover-front(L) by using the (-)driver. 4) Pull the lever and open the assy-door. 5) Part the diaphragm and the wire diaphragm away from the frame-front. 6) Remove the eight screws fixing the frame-front. 7) Its possible to exchange and service the heater, the pump, the shock-absorber and the door lock s/w.
3. BELT 1) Remove the top-cover. 2) Disassemble and assemble the belt. 3) Check the belt is located at center of the motor-pulley. <When assemble the belt> Hook the belt on the motor pulley 1) and place it around the pulley 2).

BELT 2

PULLEY
4. MOTOR 1) Lay down the washer on left side. 2) Remove the wire housing from the motor. 3) Remove the bolt fixing the motor with the box drive on back side. 4) Remove the motor.

Motor Assemble Hole

5. How to Assemble the RELAY Housing. <CAUTION> Insert the Relay Housing to the Relays on the opposite direation each other.

RELAY Housing

Heat Sink
11. Tools for Disassembly and Assembly
NO 1 TOOL Box driver 10mm 13mm 17mm 19mm 2 Double-ended spanner 10, 13 17, 19mm Heater (1) Motor (1), Balance (5) 2 holes of each left and right of the shock absorber 1 Pulley hole Replaceable for the box driver. Since the bolt runs idle when the box driver is used, use the box driver 17mm. 5 Vice pliers Other(Driver, Nipper, Long nose) JIG for the Tub Tool to protect the idle and abrasion of the bolt for the box driver. General tools for the after service. 1 (Disassemble and Assemble)

6. Trouble Diagnosis

As the micom wash machine is configured of the complicate structure, there might be the service call. Below information is prepared for exact trouble diagnosis and suitable repair guide.
Caution for the Repair and Replacement
Please follow below instruction for the trouble diagnosis and parts replacement. 1) As some electronic components are damaged by the charged static electricity from the resin part of wash machine or the human body, prepare the human body earth or remove the potential difference of the human body and wash machine by contacting the power supply plug when the work contacting to PCB is executed.

POWER SUPPLY PLUG

2) Since AC220~240V is applied to the triac T1 and T2 on P.C.B, the electric shock may occur by touching and be careful that the strong and weak electricity are mixed. 3) If the P.C.B assembly is out of order, do not replace the component on P.C.B except TACT switch since the component is coated by the urethane. 4) As the P.C.B assembly is designed for no trouble, do not replace the P.C.B assembly by the wrong diagnosis and follow the procedure of the trouble diagnosis when the micom is not operated normally. 5) As the parts on P.C.B are coated by the urethane, they can not be tested by the test bar of the meter. Check the trouble by the test mode method according to the procedure.

The power is not supplied

Cause and treatment

- Is the PCB connector connected well? - Is the voltage normal? - Is the power supply plug connected well? - Is the noise filter connected well? - Is the secondary output of the power supply transformation normal? - Is the fuse disconnected? If above points are not found, the PCB assembly is out of order. Replace it. - Is the knob open? - Did you push START/PAUSE button after selecting the course? - Is the water supply valve connected well? - Is the winding of the water supply valve continuous? - Is the connection and operation of the pressure switch normal? If above points are not found, the PCB assembly is out of order. Replace it. - Is the connection and operation of the pressure switch normal? - Is the pressure switch hose damaged so that the air is leaked? - Is the pressure switch hose bent? - Check the operation of the water level switch. If above points are not found, the PCB assembly is out of order. Replace it. - The PCB assembly is out of order. Replace it. - Is the belt connected well? - Is the winding of the motor continuous? (Rotor winding, stator winding, generator) - Is the motor fuse normal? If above points are not found, the PCB assembly is out of order. Replace it. - The PCB assembly is out of order. Replace it. (Inversion relay open trouble) - Is the drainage hose bent? - Is the winding of the drainage pump continuous? - Is the drain filter clogged by the waste? If above points are not found, the PCB assembly is out of order. Replace it. - The unbalance is detected. - Put in the laundry uniformly and start again. - Is the pulley nut loosen? - Is the transport safety device removed? - Is the product installed on the level and stable place? (Little noise may be generated during the high-speed SPIN.) <When the leak breaker and current breaker is installed separately> - When the leak breaker is down, check and make the earth of the outlet. - When the current is down, the current is leaked. <Is the breaker down when the leak/current breaker is combined?> - Check the rated capacity of the current and leak breaker. The current breaker may be down due to the lack of the current when the wash machine and other apparatus are used. In this case, execute the cold water wash to check whether the current capacity is lack. - Is the wash heater terminal unplugged? - Is the wash heater normal?(Resistance value : 20.5~21.5) - If above points are not found, the PCB assembly is out of order. Replace it.

The water is not supplied.
The wash does not start though the water supply is stopped.
The wash is executed while the water is supplied. The drum does not rotate during washing.
The drum rotates by one direction during washing. (The drum rotates to one direction for SPIN.) Drainage problem.
Dehydration problem. Abnormal noise during SPIN.
Leak breaker or current/leak breaker is down during washing.
The heating is not executed.

7. Test Mode

1. Driving Compartment Test Mode A. Hold down 2 and 1 keys simultaneously and then press O(POWER S/W) on. (Display shows tE) Hold down 1 and 2 keys simultanesously (each processing for 0.3sec) and then press O(POWER S/W) on. B. The driving compartment can be tested when you press 3 key right after entering into the intial stage of the TEST MODE. s Driving Compartment Test Pre-wash VALVE ON(0.3sec) OFF(0.3sec) Main wash(0.3sec) OFF(0.3sec) Rinse VALVE ON(0.3sec) OFF(0.3sec) Pump MOTOR ON(0.3sec) OFF(0.3sec) MOTOR RELAY1 ON(0.3sec) OFF(0.3sec) MOTOR RELAY2(0.3sec) OFF(0.3sec) MOTOR RELAY2 ON(0.3sec) OFF(0.3sec) HEATER RELAY ON(0.3sec) OFF(0.3sec) DOOR OPEN (Function continues when door is closed)
8. Designation of Main Components
8-1 Normal / Reverse Revolution of Motor and R. P. M. Control

HIGH-SPEED TACHO

MIDDLE-SPEED

Stator coil

PROTECTOR (150 C)

STATOR

5 WASHING MOTOR

<Figure3>

<Figure1>

<Figure2>

STATOR(5.10) STATOR(5.1) ROTOR(8.9) TACHO(3.4) PROTECTOR(6.7) H(mm) Code-No Resistance value 1.64 0.91 1.9 42.52 DC31-10181A 2.07 0.90 2.35 42.45 DC31-00002C Rated value 220~240V / 50Hz

Remark A B

8-2 Door safety Device

Solenoid

220/240V ED 1.0% KB 1s SD 100s 12A 125~250V AC
220/240V ED 1.0% KB 1s SD 100s
SOLENOID Coil Resistance 210 10% DC61-00122A

DC61-00115A

8-3 Heater
1) Capacity : AC 230V/2000W 2) Location : Bottom of TUB 3) Function : Raise the water temperature supplied at the wash process. 4) Resistance value : 23 ~ 29 5) Thermo Fuse : 128C SAMSUNG ELECTRONICS CO., LTD

Thermistor

8-4 ASSY-TUB
INNER-BEARING OUT-BEARING

OIL-SEAL

(unit : mm) TYPE INNER-BEARING(A) OUT-BEARING(B) OIL-SEAL(C) I II 43.9 24.3 CODE-NO REMARK
DC97-00214A SPIN SPEED OVER 1000rpm DC97-00214B SPIN SPEED BELOW 800rpm

8-5 ASSY- FLANGE SHAFT

(unit : mm) TYPE I II (A) (B) (C) 44.CODE-NO REMARK
DC97-00216A SPIN SPEED OVER 1000rpm DC97-00214A SPIN SPEED BELOW 800rpm
12. Expolded View and Parts List

Code No

DC47-00001A DC61-30346A DC61-40348B DC61-40344A DC61-60496A DC60-20061C DC62-20311A DC60-60188A DC60-20061C DC91-12281A DC97-00785A DC97-00785B DC62-40183A DC61-30347A DC61-30347B DC61-30347C DC61-60499B DC61-60520A DC97-00214A DC97-00214A

Description

HEATER TUB-FRONT BRACKET-NUT BRACKET-HEATER SPACER-HEATER SCREW TAPPING VANE-CHECK WASHER-PLAIN SCREW TAPPING ASSY-DRUM ASSY-DRUM ASSY-DRUM PACKING-TUB TUB-BACK TUB-BACK TUB-BACK CLIP-TUB CLIP-TUB ASSY-FLANGE SHAFT ASSY-FLANGE SHAFT

Specification

230V,2000W,230V,2000W,P6091 FRPP(GR30%),IVORY,SWF-P12 SBHG-R,T3,P1291,NO-PAINT STS430,T1,SWF-P12,PBT,SWF-P12,TH,+,2,D4,L12,STS304,EPDM,BLK,SWF-P12,-,ID4.5,OD15.5,T1,SWF-P12,STS3 TH,+,2,D4,L12,STS304,P1091 SWF-P8/P6091 P1291 EPDM,BLK,SWF-P12 SWF-P12 SWF-P12V SWF-P6V HSWR,P1291,NO/PAINT SK5,SWF-P12,PLATE-TYPE P1291/P1091, ALDC+SM45C P8091/P6091, ALDC+SM45C

Remark

15 15-1
See on page12 See on page12
NO Code No Q'ty Description
DC91-12078A DC61-20219A DC91-12077A DC60-40138A DC60-60044B DC60-60040A DC66-60154A DC61-60497A DC62-10305A DC60-40140A DC60-40132B DC62-10303A DC66-60153A DC62-40184A DC61-10676A DC60-20014A DC61-60497A DC62-10304A DC65-60118F DC66-10176B DC60-60049A DC60-50014A DC66-10139B DC31-10181A 1 ASSY-WIRE DIAPHRAGM DOOR-DIAPHRAGM ASSY-CLAMP DIAPHGRAM BOLT-W.MOTOR WASHER-PLAIN WASHER-NYLON WEIGHT-BALANCER CLAMP-HOSE HOSE-DRAWER TUB BOLT-HEX BOLT-FLANGE HOSE-AIR WEIGHT-BALANCER PACKING-TRAP CAP-TRAP SCREW TAPPING CLAMP-HOSE HOSE-FILTER TUB BAND RING PULLEY WASHER-SPRING NUT-HEX BELT-TRANSMISSION MOTOR-DRUM MOTOR-DRUM CUSHION-MOTOR BOLT-W.MOTOR
SWF-P12,EPDM,GRY,SWF-P12 SWF-P12,SM10C,HEX,M8,L62,-,ZPC2(YEL),-,SBC,ID8.4,OD30,T3,-,-,-,ID10.5,OD32,T2,-,PBSP-1/2H CONCRETE,SWF-P12,LOWER HSWR,SWF-P12,ID70/OD75.8(TUB) EPDM,ID35,BLK,L158,SWF-P12/OD4 WEIGHT-UL/SM10C,HEX,M8,L147,-,ZPC2(YEL) M8,L210,ZPC2(YEL),SS41C EPDM,ID24,BLK,L130,SWF-P12/OD4 CONCRETE,SWF-P12,UPPER EPDM,BLK,SWF-P12(T3) PP(TB53),-,SWF-P12 TH,-,2,D4,L12,ZPC2,HSWR,SWF-P12,ID70/OD75.8(TUB) EPDM,ID65,BLK,L151,SWF-P12/OD7 PW1,YEL,-,PI/33 ALDC,-,D297,P1291,ID12.5 -,ID10.5,OD18,T2.5,-,SIR HEXAGON,M(12),ZPC2(YEL),SM10C, -,-,-,-,MCC 52/64 148/SEC1,220~240V,50HZ,52MM MCC 45/64 148/SEC1,220~240V,50HZ,45MM BUTYL,SWF-6V,ID16/OD20 SM10C,HEX,M8,L62,-,ZPC2(YEL),-,-

NSA Remark

See on page11 See on page11
27-1 DC31-00002C DC61-00041A DC60-40138A

NO Code No

1 1-1 1-2-12-13-16-21-40-1 40-DC96-00070A DC96-00070B DC96-00052B DC96-00053A DC96-00053B DC60-20136A DC61-30344A DC32-30006P DC61-60063B DC62-10311A DC60-20050C DC60-20054C DC60-30015B DC97-00851A DC97-00218A DC61-30345A DC61-00056A DC60-20054C DC60-20030A DC61-00115A DC61-00122A DC66-30160A DC61-70216C DC61-60180A DC61-70217C DC62-30313A DC62-30314A DC61-60063B DC62-10068A 6001-000947 DC29-00003A DC29-90001A DC60-20138A DC96-00146A DC61-40081A DC97-00139B DC65-60118F DC99-00033A DC99-00040A DC91-12292A DC66-60149A DC60-40026A DC61-10672A DC61-10673A DC62-10302A DC90-11110K DC96-00149A DC96-00035J 6002-000444

Q'ty Description

0.2 ASSY-M.WIRE HARNESS ASSY-M.WIRE HARNESS ASSY-M.WIRE HARNESS ASSY-WIRE HARNESS ASSY-WIRE HARNESS SCREW TAPPING FRAME-PLATE(U) SENSOR PRESSURE CLAMP-HOSE HOSE-PRESSURE SCREW TAPPING SCREW TAPPING SCREW-SPECIAL ASSY-COVER TOP ASSY-COVER TOP FRAME-FRONT FRAME-FRONT SCREW TAPPING SCREW TAPPING DOOR-LOCK S/W DOOR-LOCK S/W LEVER SPRING-HANGER SLEEVE-PLUG SPRING-HANGER VALVE-WATER VALVE-WATER CLAMP-HOSE HOSE-DRAWER SCREW-MACHINE FILTER-EMI FILTER-EMI SCREW TAPPING ASSY-POWER CORD HOLDER-WIRE ASSY-HOSE DRAIN(O) BAND RING PAINT PAINT ASSY-LEG DAMPER-SHOCK BOLT-HEX COVER-FRONT(L) CAP-DRAIN HOSE-DRAIN ASSY-PUMP DRAIN ASSY-PUMP DRAIN ASSY-PUMP DRAIN SCREW-TAPPING
P1291/1191/1091/8091,COLD+HOT P1291/1191/1091/8091,COLD-ONLY P6091,COLD-ONLY P1291/1191/1091(SUB),HIGH-RPM P8091/P6091,(SUB),LOW-RPM TH,+,2,D5,20,ZPC3,COVER-TOP EGI,NTR,SWF-P12 DN-S14,TERMINAL-TYPE(DC5V) SK5,-,YEL EPDM,ID13.5,BLK,-,SWF-P12/OD17 -,-,2S,D3,L8,FZY,TH,+,1,D4,L12,FE FZY,FLANGE,PH,+,D4,L12,ZnFe(YEL),SWF-P12, WOOD TYPE STEEL TYPE EGI,WHT,SWF-P12 EGI,WHT,P6091 TH,+,1,D4,L12,FE FZY,FH,-,1,D4,L12,NTR,230V/50HZ,GRY,250V(16A) P6091 PE,L335,SWF-P12(ORG) HSWR,OD24,-,-,-,-,P1291,LEFT(RED/SPRAY) NYLON#6,SEW-720DR,NTR HSWR,OD30,-,-,-,-,P1291,RIGHT(NO-PAINT) NYLON#6,SWF-P12,EATON(COLD) NYLON#6,SWF-P12,EATON(COLD+HOT) SK5,-,YEL SOFT-PVC,ID10,NTR,L350,TH,+,M4,L10,NTR/WHT,STS304 FA-2151TS-1,250V,15A,2200PF,P1291,-25/+85'C AC LINE:FA-215T2-D PH,TORX,1,D4,L12,ZPC2,P1291~P6091,250V/16A(PV) NYLON66,-,DAWH-3NB,NTR(PI15) SWF-P12V,PP(BB110)2200 PW1,YEL,-,PI/33 SBHG1-A,WHT,P1291(COLD) P6091,COLD SWF-P12,-,SWF-P12,80N M10,-,-,SCP PP(BJ-730),WHT,SWF-P12 PP(TB53),WHT,SWF-P12 EPDM,ID5.5,BLK,L220,OD9.5 P1291/P1091, 220V~240V/50Hz P8091/P6091, 220V~240V/50Hz 220V~240V/60Hz TN,+,2S,M4,L14,NTR,STS304

DC64-20013A DC64-20013B

DECORATION-LID DECORATION-LID COVER-DOOR COVER-DOOR DOOR-GLASS HOLDER-GLASS HOLDER-GLASS SCREW TAPPING ASSY-HINGE SCREW MACHINE LEVER-DOOR LEVER-DOOR SCREW TAPPING NUT-FLANGE
ABS,SIL/COATING,SWF-P12,SWF-P10 / P8,ABS,WHT,SWF-P12 ABS,WHT,P6091 GLASS,NTR,SWF-P12 ABS,WHT,SWF-P12,ABS,WHT,P6091 TH,+,2,D4,L8,FE,FZY SWF-P12,NI+CR RH,+,M5,L12,STS430,SEAL-LOCK ZnDC,L40,SWF-P12 P6091 FH,+,1,D4,L20,STS304,-,-,-,M5XP0.8,FZY,MSWR10,-

2 2-4 4-9 9-11

DC61-10682A DC61-00055A DC61-00013A DC61-40346A DC61-00057A DC60-20060A DC97-00100A DC60-10019B DC66-30161A DC66-00016A DC60-20140B DD60-50018A
2 DC97-00004G DC97-00004M DC97-00004N DC97-00004P DC61-30348A DC61-60498A DC61-10687A DC97-00003M DC97-00003S DC97-00703N DC97-00003T DC97-00703P DC97-00003U DC97-00003V 6002-000445 MF-P1291-00 MF-P1191-00 MF-P1091-00 DC96-00135A MF-P6091-00 6002-000554 DC91-12084A DC61-10679A
ASSY-PANEL FRONT ASSY-PANEL FRONT ASSY-PANEL FRONT ASSY-PANEL FRONT BODY-DRAWER GUIDE-LIQUID CAP-RINSE ASSY-PANEL CONTROL ASSY-PANEL CONTROL ASSY-PANEL CONTROL ASSY-PANEL CONTROL ASSY-PANEL CONTROL ASSY-PANEL CONTROL ASSY-PANEL CONTROL SCREW-TAPPING ASSY-PCB PARTS ASSY-PCB PARTS ASSY-PCB PARTS ASSY-PCB PARTS ASSY-PCB PARTS SCREW-TAPPING ASSY-HOUSING D.W(U) HOUSING-DRAWER(L)

15. TOP(FRONT) - EXPLODED VIEW
G007 Y001 C010 G012 G013 J006 G034 G028 C053 V030 G040 C062 V010 G027

V031 P002 V009

V004 F004

15. TUB - EXPLODED VIEW

R025 R014 R020 R008
R026 R003 R013 R005 R028 R021 R007

R074 R006

15. CASE - EXPLODED VIEW
J008 T024 J011 J012 R030 J010 C080 J012 G002

R017 G003

G023 G009

15. PARTS LIST

NO. B006 C007 C010 C023 C051 C051 C051 C053 C080 F004 F004 G002 G003 G007 G007 G008 G009 G012 G013 G015 G018 G020 G023 G025 G027 G027 G028 G028 G034 G040 J001 J006 J008 J010 J010 J011 J012 J012 J014 CODE NO. DC91-12292A DC96-00829A DC61-10687A DC32-30006P DC97-06855W DC97-06855X DC97-06855Y DC61-00932A DC62-00024F DC64-00561D DC64-00561A DC91-12102A DC97-00139F DC97-05128A DC97-05128B DC96-00146A DC90-11110K DC64-00559C DC64-00565A DC61-10673A DC61-20235A DC63-00562A DC62-10302A DC62-10289B DC64-00558C DC64-00558A DC64-00556A DC64-00556B DC64-00570A DC64-00567A DC97-07874A DC61-30348A DC29-00009A DC67-00051A DC67-00138A DC61-60180A DC61-70216C DC61-70217C DC97-06572W DESCRIPTION ASSY-LEG ASSY-M.WIRE HARNESS CAP-RINSE SENSOR PRESSURE ASSY-PANEL CONTROL ASSY-PANEL CONTROL ASSY-PANEL CONTROL HINGE-DOOR VALVE-WATER HANDLE-DOOR HANDLE-DOOR ASSY-FIXER TUB ASSY-HOSE DRAIN(O) ASSY-PANEL FRONT ASSY-PANEL FRONT CBF-POWER CORD ASSY-PUMP DRAIN BUTTON-ENCODER BUTTON-PUSH CAP-DRAIN SHUTTER COVER-FRONT(L) HOSE-DRAIN HOSE-WATER(C) KNOB-ENCODER KNOB-ENCODER PANEL-DRAWER PANEL-DRAWER HANDLE-DRAWER BUTTON-PUSH(P) ASSY-COVER TOP BODY-DRAWER FILTER-EMI HOSE-DRAWER HOSE-DRAWER SLEEVE-PLUG SPRING-HANGER SPRING-HANGER ASSY-HOUSING DRAWER SWF-P12,B1445AV~B1045A,MAIN/CLONE-PJT SWF-P12,PP,-,-,-,WHT,-, DN-S14(P1291),TERMINAL-TYPE(DC5V) B1445AVGW/YLP,RUSSIAN/WHITE B1245AVGW/YLP,RUSSIAN/WHITE B1045AGW/YLP,RUSSIAN/WHITE Q1636GW/XEU,ZNDC,-,-,-,-,-,TS-2 PJT B1215J,NYLON66/250TRMN,-,-,NTR,2-WAY(220~240V50/60HZ)ELBI Q1636V,ABS,-,-,-,-,SILVER-SPRAY,TS-2 PJT Q1636,ABS,-,-,-,-,WHT,TS-2 PJT SWF-P12,P-PJT,PP/L1970/CHINA Q1636V/WHT,SAMSUNG/STAMP Q1636,WHT/SAMSUNG,NO-STAMP UCP2,-,250V/16A,-,-,-,-,-,-,-,P1291,SWF-P12,220V~240V/50Hz Q1636V,ABS,-,-,WHT,ICON Q1636,ABS,-,-,WHT,TS-2 PJT SWF-P12,PP(TB53),-,-,-,WHT,-, DANPLA,PP(BB110),WHT, P1445,PC(ABS),-,-,-,-,-,WHT,CLON-PJT SWF-P12,EPDM,ID5.5,-,-,L220,BLK,OD9.5 WIP4013SRW,PVC+NYLON,ID10.2,-,-,L1500,GRY,COLD/H19/REFLEX Q1636S,ABS,-,-,-,-,CR-COATING,-,NON-BRIGHT Q1636,ABS(HG-0760),-,-,-,-,WHT,-,TS2-PJ Q1636V,ABS(HG-0760),-,-,-,-,WHT/SAMSUNG,NO-BRIGHT_STAMP Q1636,ABS(HG-0760),-,-,-,-,WHT/SAMSUNG,NOT-STAMPING Q1636GW/XEU,ABS(HG-0760),-,-,-,-,WHT,TS-2 PJT Q1636V,ABS,-,-,WHT,TS-2 PJT B1445AV/WHT/WOOD,CLON-PJT -,PP,-,-,-,-,-,DFC-2715R,P/PV/P2,250V,15A,PI38.2XH60,-,-,VDE,-,S1093~S6093,EPDM,-,-,-,-,BLK,SLIM-PJT F1235AS,EPDM,-,-,-,L92,BLK,AG+ NYLON#6,SEW-720DR,-,-,NTR P1291,HSWR,CD3.5,-,-,L175,-,-,-,-,P1291,HSWR,CD3.2,-,-,L175,-,-,-,-,B1445AV/CLON-PJT,AG+/2WAY/COLD SPECIFICATION QTY 1 0.B1445AV B1245AV B1045A B1445AV B1245AV B1045A B1445AV B1245AV B1045A B1445AV B1245AV B1045A B1445AV B1245AV B1045A REMARK
NO. J014 P002 P007 P011 R003 R005 R006 R007 R007 R008 R010 R012 R013 R014 R015 R016 R017 R018 R020 R021 R024 R025 R026 R028 R030 R074 T024 T031 V001 V001 V004 V007 V009 V010 V022 V030 V031 V031 Y001 Y001 Y001 Y001 CODE NO. DC97-03244A DC97-05133A DC99-00524A DC61-01245A DC91-12077A DC97-01463F DC47-00007A DC97-00214D DC97-00214E 6602-001072 DC61-00856A DC66-00320A DC61-20219A DC62-10303A DC62-10305A DC62-10304A DC67-00107A DC31-00002F DC66-10176B DC62-00008A DC62-20311A DC66-60153A DC66-60154A DC62-40183A DC61-40345A DC61-30346C DC96-00570B DC61-00041A DC63-00411D DC63-00411A DC97-05111A DC91-12078A DC61-00013A DC64-00653A DC61-10676A DC64-00562A DC61-00931B DC61-00931A MES-AGMOD-S2 MFS-B1445A-00 MFS-B1245A-00 MFS-B1045A-00 DESCRIPTION ASSY-HOUSING DRAWER ASSY-FRAME FRONT ASSY-PAINT FRAME FRAME-PLATE(U) ASSY-CLAMP DIAPHGRAM ASSY-DRUM HEATER ASSY-TUB BACK ASSY-TUB BACK BELT-TIMING GEAR BRACKET-HEATER DAMPER-SHOCK DOOR-DIAPHRAGM HOSE-AIR HOSE-DRAWER TUB HOSE-FILTER TUB HOSE-PRESSURE MOTOR-DRUM PULLEY SEAL-OIL VANE-CHECK WEIGHT-BALANCER WEIGHT-BALANCER PACKING-TUB BRACKET-PRESSURE TUB-FRONT ASSY-WIRE HARNESS CUSHION-MOTOR COVER-DOOR COVER-DOOR ASSY-LEVER DOOR ASSY-WIRE DIAPHRAGM DOOR-GLASS DOOR-LOCK S/W CAP-TRAP WINDOW-ENCODER HOLDER-GLASS HOLDER-GLASS ASSY PCB PARTS ASSY PCB PARTS ASSY PCB PARTS ASSY PCB PARTS B1215J,FOR/2WAY Q1636GW/XEU,TS-2 PJT B1445AV,CLON-PJT/WHITE MW24-PJT,EGI,-,-,-,T0.8,-,-,MW24 SWF-P12,TUB P1205/KRNJM,LEFTER TYPE/NEW-DRUM -,DRUM-MDL,SUS316L,-,-,230V,20,-,-,2000W SWF-P14,BACK/1400/INSIDE-ASY SWF-P12/10,BACK/1200/INSIDE-ASY POLYURETHAN,L1270,J5,MEGADYNE,NTR SB-PJT,STS430,-,-,-,-,SB-PJT,ABS,-,-,-,-,WHT,AKS-DAMPER/50N EPDM,-,-,-,-,-,-,GRY,SWF-P12(WASH) -,EPDM,ID24,-,-,L130,BLK,SWF-P12/OD47 -,EPDM,ID35,-,-,L158,BLK,SWF-P12/OD40 -,EPDM,ID65,-,-,L151,BLK,SWF-P12/OD70 S821,PE-BLOW,ID13.2,OD6.2,-,-,NTR,HXGM4I,SFW-P12,-,50Hz,WASHING 40W,SPINNING 400W,HIGH RPM,-,220~240V,INSULATED CL ALDC,-,D297,P1291,ID12.5 -,NBR(SD35),BLK,-,-,-,NBU(PI15) SWF-P12,EPDM,-,-,BLK,-, SWF-P12,CONCRETE,UPPER, SWF-P12,CONCRETE,LOWER, SWF-P12,EPDM,-,-,-,-,-,BLK,-,GI or GA,SWK-P12,T1.0,-,-,-,P1405J,FRPP(FRPP15%)SAMBACK,-,-,-,SEW-HW/HR125/3HW/3HR,SUB/6PCABLE/TUBE ADD SWF-6V,BUTYL,-,-,-,ID16/OD20, Q1636V,ABS,-,-,-,-,-,SILVER-SPARY,TS-2 PJT Q1636,ABS,-,-,-,-,-,WHT,TS-2 PJT Q1636GW/XEU,TS-2 PJT SWF-P12,FRAME-FRONT GLASS,NTR,SWF-P12 DA,PA6-G,-,H82,W50,-,BLK,250V/16A/ROLD SWF-P12,PP(TB53),-,-,-,-,-, Q1636,ACRYL,-,-,-,-,NTR,HOLE14 Q1636V,PP(TB53),-,-,-,GRAY,TS-2 PJT Q1636,PP(TB53),-,-,-,WHT,TS-2 PJT TORNADO-AG+ CHINA MFS-B1445-00 AG+ Q2 MFS-B1245-00 AG+ Q2 MFS-B1045A-00 AG+ Q2 SPECIFICATION QTY B1445AV B1245AV B1045A B1445AV B1245AV B1045A B1445AV B1245AV B1045A B1445AV B1245AV B1045A B1445AV B1245AV B1045A REMARK

16. SCREW BOLT LIST

CODE NO. 6002-000471 6001-001773 6002-001286 6002-000213 6002-000239 6002-000239 6002-000525 6002-000554 6002-001006 6002-001327 6006-001170 6009-001343 DC60-40144A DC60-40146A DC60-40142A DC60-60040A DC60-60044B 6002-000213 6002-000213 6002-000213 6002-000445 6002-000554 6002-001327 6003-000226 6003-000226 6006-001170 6006-001170 6006-001170 6009-001342 6002-000630 DC60-40141A DC60-50148B DC60-60040A DC60-60044A DC60-60044B DC60-60049A DC61-00201A 6006-001170 DC61-40348B 6002-000213 6002-000444 6002-000471 6002-001327 DC61-40348B DC60-40005A DC60-50010A DC60-50010B 6011-001492 DC97-02412A DC97-02412A DC97-02412B DC97-02412B DC97-02412C DESCRIPTION SCREW-TAPPING SCREW-MACHINE SCREW-TAPPING SCREW-TAPPING SCREW-TAPPING SCREW-TAPPING SCREW-TAPPING SCREW-TAPPING SCREW-TAPPING SCREW-TAPPING SCREW-TAPPING SCREW-SPECIAL BOLT-HEX BOLT-SPANER BOLT-HEX WASHER-NYLON WASHER-PLAIN SCREW-TAPPING SCREW-TAPPING SCREW-TAPPING SCREW-TAPPING SCREW-TAPPING SCREW-TAPPING SCREW-TAPTITE SCREW-TAPTITE SCREW-TAPPING SCREW-TAPPING SCREW-TAPPING SCREW-SPECIAL SCREW-TAPPING BOLT-HEX NUT-HEX WASHER-NYLON WASHER-PLAIN WASHER-PLAIN WASHER-SPRING BRACKET-NUT SCREW-TAPPING BRACKET-NUT SCREW-TAPPING SCREW-TAPPING SCREW-TAPPING SCREW-TAPPING BRACKET-NUT BOLT-HEX NUT-DIAPHRAGM NUT-DIAPHRAGM BOLT-FLANGE ASSY-BOLT ASSY-BOLT ASSY-BOLT ASSY-BOLT ASSY-BOLT TH,+,M5,L12, FH,+,1,M4,L16,NTR,STS304,TH,+,1,M4,L12,ZPC(YEL),SWRCH18 TH,+,2S,M4,L8,ZPC(YEL),SM20C TH,+,2S,M4,L8,ZPC(YEL),SM20C FH,+,1,M4,L12,PASS,STS304 PH,+,2S,M4,L12,ZPC(YEL),SWRCH1 TH,+,2S,M4,L12,-,STS410 PWH,+,1,M4,L12,NI PLT WS,TH,+,M4,L10,ZPC(YEL) PH,TORX,,M4,L10,PASS M10,L41,ZPC2(YEL),SM10C/DAMPER -,-,OD36,T2.5,L52,FE,FZY,-,P12 SM10C/FIXER,HEX,M7,L88.4,-,ZPC2(YEL),-,-,ID10.5,OD32,T2,-,PBSP-1/2H SBC,ID8.4,OD30,T3,-,-,TH,+,1,M4,L12,ZPC(YEL),SWRCH18 TH,+,1,M4,L12,ZPC(YEL),SWRCH18 TH,+,1,M4,L12,ZPC(YEL),SWRCH18 TH,+,2S,M4,L18,NTR,STS304 PH,+,2S,M4,L12,ZPC(YEL),SWRCH1 PWH,+,1,M4,L12,NI PLT TH,+,S,M4,L8,ZPC(YEL),SWRCH18A TH,+,S,M4,L8,ZPC(YEL),SWRCH18A WS,TH,+,M4,L10,ZPC(YEL) WS,TH,+,M4,L10,ZPC(YEL) WS,TH,+,M4,L10,ZPC(YEL) TH,+,,M5,L11,ZPC(YEL) PH,+,2S,M3,L8,ZPC(YEL),SWRCH18 SM10C/DAMPER,HEX,M8,L66,-,ZPC2(YEL),-,SM20C(NYLON),M12,-,-,ZPC3(YEL),-,HEX,P-PROJECT -,ID10.5,OD32,T2,-,PBSP-1/2H -,ID10.5,OD30,T3,-,STS304 SBC,ID8.4,OD30,T3,-,-,-,ID10.5,OD18,T2.5,-,SIR SBHG-R,P1291,T3,-,-,-,NO-PAINT/MOTOR WS,TH,+,M4,L10,ZPC(YEL) SBHG-R,P1291,T3,-,-,-,NO-PAINT TH,+,1,M4,L12,ZPC(YEL),SWRCH18 TH,+,2S,M4,L14,NTR,STS304 TH,+,1,M4,L12,PASS,STS304,PWH,+,1,M4,L12,NI PLT SBHG-R,P1291,T3,-,-,-,NO-PAINT M4,L60,ZPC2(YEL),SS41C,-,-,-,EGI,M4,-,-,2.5TX20X8 EGI,M4.2,-,-,2.5TX20X8 M8,L25,PASS,STS304,NYLOCK,P1.25 SWF-P12,MOTOR, M8*L62 SWF-P12,MOTOR, M8*L62 SWF-P12,WEIHGT(L)/M8*L147 SWF-P12,WEIHGT(L)/M8*L147 SWF-P12,WEIHGT(U)/M8*L215 SPECIFICATION TH,+,1,M4,L12,PASS,STS304,REMARK D-S/W+FRM-FRONT HINGE+FRAME C-DOOR+H-GLASS CLAMP-HOSE+FRAME FRAME+FRAME-FRONT FRAME+PLATE-UPPER C-PANEL+FRAME PCB+C-PANEL PUMP+FRAME SHUTTER E/W(SUB)+FRAME(F) P/CORD DAMPER+FRAME ACCESSORY FIXER FIXER BUTTON-WINDOW(L&R) HOUSING-DRAWER SUB PCB-ASSY+FRAME PANEL+FRM+HOUSING-D HOUSING-DRAWER C/TOP+FRAME GUIDE WATER+FRAME W/V(C)+FRAME B/K-PRESSURE+FRAME EMI-EARTH+FRAME P/CORD(E/W) FRAME(TOP) B/K+PRE-S/W DAMPER+TUB PULLEY WEIGHT/L DAMPER+TUB WEIGHT/L PULLEY MOTOR CAP-TRAP B/K-HEATER VANE-CHECK MOTOR WEIGHT-BALANCER(U) WEIGHT-BALANCER(L) WEIGHT-BALANCER(U) WEIGHT-BALANCER(U) QTY 1

ELECTRONICS

This Service Manual is a property of Samsung Electronics Co.,Ltd. Any unauthorized use of Manual can be punished under applicable International and/or domestic law.
Samsung Electronics Co., Ltd. JUNE 2004 Printed in Korea Code No. : DC68-02212A