When cleaning the product, disconnect the power cord and clean it softly with a dry cloth. (Do not use chemicals such as wax, benzene, alcohol, thinner, mosquito repellant, lubricant, or cleaner.) These may change the appearance of the product surface and peel off the indication labels on the product.
Since the product housing is easily scratched, make sure to use the specified cloth only. Use the specified cloth adding only a little water. As the product may be scratched if there is any foreign material on the cloth, make sure to shake it thoroughly before using it.
When cleaning the product, do not spray water directly onto the main body of the product. Ensure that water does not enter the product and that it is not wet. Otherwise, this may result in electric shock, fire or a malfunction.

Others

The product is a high voltage product. Ensure that users do not disassemble, repair or modify the product themselves. Otherwise, this may result in electric shock or fire. If the product needs to be repaired, contact a Service Center.
If there is a strange smell or a strange sound or smoke is coming from the product, disconnect the power plug immediately and contact a Service Center. Otherwise, this may result in electric shock or fire.
Do not place this product in a location exposed to moisture, dust, smoke, water, or in a car. Otherwise, this may result in electric shock or fire.
When you drop the product or the case is broken, turn the power off and disconnect the power cord. Contact a Service Center. Otherwise, this may result in electric shock or fire.
If thunder or lightening is occurring, do not touch the power cord or antenna cable. Otherwise, this may result in electric shock or fire.
Do not try to move the monitor by pulling only the wire or the signal cable. Otherwise, it may fall and result in electric shock, damage to the product or fire due to damage to the cable.
Do not lift or move the product back and forwards or right and left while only holding the power cord or signal cables. Otherwise, it may fall and result in electric shock, damage to the product or fire due to damage to the cable.
Make sure that the ventilating opening is not blocked by a table or curtain. Otherwise, it may result in fire due to an increase in the internal temperature.
Do not place any containers containing water, vases, flowerpots, medicines as well as any metal on the product. If water or a foreign material enters the product, disconnect the power cord and contact a Service Center. This may result in a product malfunction, electric shock, or fire.

Do not use or keep combustible spray or flammable material near the product. Otherwise, this may result in an explosion or fire.
Do not insert any metal, such as chopsticks, coins, pins and steel, or flammable objects, such as matches or paper, inside the product (through the ventilating openings, input and output terminals, etc). If water or foreign material enters the product, disconnect the power cord and contact a Service Center. Otherwise, this may result in electric shock or fire.
When using a fixed screen for a long time, an afterimage or stain may occur. If you are not using your product for a long period of time, put it into sleep mode or use a moving screen saver. Set a resolution and frequency appropriate to the product. Otherwise, your eyesight may be damaged.
When using headphones or earphones, do not turn the volume too high. Having the sound too loud may damage your hearing.
If you continually move closer to the product screen, your eyesight may be failing.
To ease eye strain, take at least a five-minute break after every hour of using the monitor.
Do not install it in an unstable location such as an unstable rack or uneven surface or a location exposed to vibrations. Otherwise, it may fall and cause personal injury and/or damage the product. If you use the product in a location exposed to vibrations, it may damage the product and result in fire.
When moving the product, turn the power off and disconnect the power plug, antenna cable, and all the cables connected to the product. Otherwise, it may result in electric shock or fire.
Ensure that children do not hang onto the product or climb up onto the product. The product may fall and cause personal injury or death.
If you do not use the product for a long period of time, disconnect the power cord from the power outlet. Otherwise, this may result in overheating or fire due to dust, and may result in fire due to electric shock or leakage.
Do not place any heavy items or toys or confectionery, such as cookies etc. that may attract the attention of children and to the product. Your children may hang onto the product causing it to fall and this may result in personal injury or death.
Be careful that children do not place the battery in their mouths when removed from the remote control. Place the battery in a location that children or infants cannot reach. If children have had the battery in their mouths, consult your doctor immediately. When replacing the battery, insert it with right polarity (+, -). Otherwise, the battery may become damaged or it may cause fire, personal injury or damage due to leakage of the internal liquid.
Use only specified standard batteries. Do not use new and used batteries together. This may cause a battery to break or leak and may cause fire, injury, or contamination (damage).

Unpacking

Without stand

With stand

Monitor Manuals

Monitor

Quick Setup Guide
Warranty Card (Not available in all locations)

User's Guide

Cables
D-Sub Cable Sold separately

Power Cord

Stereo Cable

DVI Cable

HDMI Cable

Headphones

Sold separately

USB Cable

TV Antenna Cable (Coaxial Cable)
Component(PR, PB, Y) Cable

Audio cable

Digital audio optic output cable
Remote Control BN59-00678A
Batteries (AAA X 2) (Not available in all locations)

Cleaning Cloth

Cable holding ring Note

Stand Body

Stand Base
Cleaning Cloth is only provided for highly polished black products as a product feature.

Your Monitor Front

Activates a highlighted menu item. Push the ' ', button to change the input signal source.
Changing the source is only allowed for external devices connected to the product at the time. To switch Screen modes: [PC] [DVI] [TV] [Component] [HDMI1] [HDMI2] >> Click here to see an animation clip MENU Use this button to open the on-screen menu and to exit from the on-screen menu or to close the screen adjustment menu. - VOL+ Moves from one menu item to another horizontally or adjusts selected menu values. Adjusts the audio volume. - CH + Moves from one menu item to another vertically or adjusts selected menu values. In TV/DTV mode, selects TV/DTV channels. Power button [ ]
Use this button for turning the product on and off.
Note The button to the right of the monitor are touch-sensitive buttons. Touch a button lightly with your finger. Power indicator This light is lit when operating normally, and blinks once when your adjustments are saved. Note See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed or when leaving it unattended for long periods. Speaker
Note The configuration at the back of the product may vary from product to product.
POWER POWER Connect the power cord for your monitor to the POWER port on the back of the product.
PC Connect the PC terminal at the back of your monitor to your computer.
HDMI/PC/DVI-D AUDIO IN DIGITAL AUDIO OUT(OPTICAL) EX-LINK HDMI/PC/DVI-D AUDIO IN Connect the [ HDMI/PC/DVI-D AUDIO IN ] terminal at the back of your product to your computers sound card. DIGITAL AUDIO OUT(OPTICAL) Connect the [DIGITAL AUDIO OUT(OPTICAL)] terminal of your product to the digital sound output or standard sound output terminal of the DVD home theater (or amplifier) using a digital audio optical output cable. EX-LINK This is a reserved terminal used for servicing. SERVICE SERVICE This is a reserved terminal used for servicing.

Connecting HDMI

Note You can connect digital output devices to your monitor. You can enjoy better screen and sound quality. 1. Connecting Using a HDMI Cable
Input devices such as digital DVD are connected to the [HDMI IN 1] terminal of the monitor using the HDMI cable. When all the connections are completed, connect the power cords for the monitor and DVD(or the device connected to the digital output terminal). Select HDMI using the SOURCE [ ] button.
Connections 2. Connecting Using a DVI to HDMI Cable
Connect the DVI output terminal of a digital output device to the [HDMI IN 1] terminal of the monitor using a DVI to HDMI cable. Connect the red and white jacks of an RCA to stereo (for PC) cable to the same colored audio output terminals of the digital output device, and connect the opposite jack to the [HDMI/PC/DVI AUDIO IN]terminal of the monitor. 3. When all the connections are completed, connect the power cords for the monitor and DVD (or the device connected to the digital output terminal). 4. Select "HDMI" using the 'SOURCE [ Note If you just connect using the DVI to HDMI cable without connecting to the sound source, you cannot hear sound. Connecting the audio output terminal of a digital device to the [R-AUDIO-L] of [COMPONENT IN] of the monitor using an audio cable will not give you sound. Make sure to connect to the [ HDMI/PC/DVI-D AUDIO IN ] terminal of the monitor. ]' button.
Connecting and Using an Amplifier
Note You can connect the digital sound input (optical) or standard sound input terminal of your amplifier to your monitor using the correct cable.
Connect the [DIGITAL AUDIO OUT (OPTICAL)] terminal of your monitor to the digital sound input terminal of your digital amplifier using an optical cable.
Connections 2. 3. 4. Set the Internal Mute On in the Sound menu using the MENU button. Adjust the sound volume using the Volume button of your amplifier If the connections are set up, power up your monitor and amplifier. Note If no sound is emitted from the monitor, you need to use an amplifier. For information on how to connect a speaker and amplifier, refer to the respective user manuals provided by their manufacturers.

Fine Tune

Due to weak signals or an incorrect antenna configuration, some of the channels may not be tuned correctly. (Available in Analog TV Mode Only) MENU , , , , MENU,EXIT

Signal Strength

Unlike analog channels, which can vary in reception quality from "snowy" to clear, digital (HDTV) channels have either perfect reception quality or you will not receive them at all. So, unlike analog channels, you cannot fine tune a digital channel. You can, however, adjust your antenna to improve the reception of available digital channels. If the signal strength meter indicates that the signal is weak, physically adjust your antenna to increase the signal strength. Continue to adjust the antenna until you find the best position with the strongest signal. (Available in Digital Cable TV Mode Only) MENU , , MENU,EXIT

Setup Available Modes

Plug & Play
You can manage the entire configuration. MENU , , , , , MENU,EXIT , , , , ,

Language

You can choose one of 3 languages.
The language chosen affects only the language of the OSD. MENU , , MENU,EXIT

Time Clock

You can set the current time.

- Clock Mode

Auto / Manual MENU , , , MENU,EXIT

- Clock Set

Note Clock Set are available only when Clock Mode set to Manual. MENU , , , , , , MENU,EXIT

- Time Zone

Note Time Zone are available only when Clock Mode set to Auto. MENU , , , , MENU,EXIT
Note DST are available only when Clock Mode set to Auto. Depending on the broadcast station and signal, the auto time may not be set correctly. If this occurs, set the time manually. The Antenna or cable must be connected in order to set the time automatically. , , , , MENU,EXIT

Sleep Timer

Use to set the Monitor to be turned off automatically in certain minutes. Off, 30, 60, 90, 120, 150, 180 , , , , , , MENU,EXIT

Timer1 / Timer2 / Timer3

You can set the monitor to be turned on or off automatically at a specified time. Note Setting the clock is necessary in order to use the various timer features of the product. Three different On/Off Timer Settings can be made. MENU , , , , , , MENU,EXIT

V-Chip

Protects children from viewing inappropriate programs by blocking certain broadcast or AV programs. (More Information) Parental restriction levels differ depending on the broadcasting station. The default menu name and Downloadable US rating change depending on the downloaded information.
Adjusting the Monitor Even if you set the On-screen display to your desired language, the"Downloadable U.S. Rating" menu will appear in English only. The rating will automatically block certain categories that are more restrictive. The rating titles(For example: Humor Level.etc) and TV ratings(For example:DH,MH,H.etc) may differ depending on the broadcasting station. If you forget the PIN, press the remote-control buttons in the following sequence, which resets the pin to 0-0-0-0 : Power Off Mute 4 Power On.

Check List

Note Before calling for assistance, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer.
1. Problems related to Installation
Note Problems related to the monitor installation and their solutions are listed.

PC Mode

Q: A: Q: A: It appears the PC does not function normally. Check if the Display Adapter Driver (VGA Driver) is properly installed. (Refer to Installing Driver) The monitor screen flickers. Check if the signal cable between the computer and the monitor is securely connected and tightened.(Refer to Connecting the monitor)

TV Mode

Q: A: Q: A: TV screen is blurred or shows noise signals. Check if the TV antenna connector is securely connected to the external antenna.(Refer to Connecting TV) TV signal is not received Select "Auto Program" to configure the channel system automatically. (Refer to the Auto Program)
2. Problems related to Screen
Note Problems related to the monitor screen and their solutions are listed. Q: A: Q: A: A: Q: A: A: Q: A: Q: A: A: A: Screen is blank and power indicator is off Ensure that the power cord is firmly connected and the LCD monitor is on.(Refer to the Connecting the monitor) "Check Signal Cable" message Ensure that the signal cable is firmly connected to the PC or video SOURCEs.(Refer to the Connecting the monitor) Ensure that the PC or video SOURCEs are turned on. "Not Optimum Mode" message Check the maximum resolution and the frequency of the video adapter. Compare these values with the data in the Preset Timing Modes Chart. Picture rolls vertically. Check if the signal cable is securely connected.Connect it again securely. (Refer to Connecting the monitor) Image is not clear. Picture is blurred. Run Frequency Coarse and Fine tuning. Turn on again after removing all accessories (video extension cable, etc.) Set resolution and frequency to the recommended ranges.
Troubleshooting Q: Picture image is unstable and vibrates. Ghost images are shown in the picture. A: Check if the resolution and frequency set for the computer video card falls in the range supported by the monitor.If not, reset them referring to the current Information under the monitor menu and Preset Timing Modes. The image is too light or too dark Adjust the Brightness and Contrast.(Refer to the Brightness, Contrast) The Power Indicator blinks. The monitor is currently saving the changes made in settings to the OSD memory. The screen is blank and the power indicator light blinks every 0.5 or 1 seconds. The monitor is using its power management system. press a key on the keyboard. The screen is blank and is blinking. If you see the "TEST GOOD" message on the screen when you press the MENU button, check the cable connection between the monitor and the computer to ensure that the connector is properly connected.

This monitor is EPA ENERGY STAR compliant and ENERGY2000 compliant when used with a computer equipped with VESA DPM functionality. As an ENERGY STAR Partner, SAMSUNG has determined that this product meets the ENERGY STAR guidelines for energy efficiency.

Preset Timing Modes

If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows. Display Mode Horizontal Frequency (kHz) 31.469 31.469 31.469 35.000 49.726 68.681 37.861 37.500 35.156 37.879 48.077 46.875 48.363 56.476 60.023 67.500 60.000 63.981 79.976 65.290 Vertical Frequency (Hz) 70.086 59.940 70.087 66.667 74.551 75.062 72.809 75.000 56.250 60.317 72.188 75.000 60.004 70.069 75.029 75.000 60.000 60.020 75.025 59.954 Pixel Clock (MHz) 25.175 25.175 28.322 30.240 57.284 100.000 31.500 31.500 36.000 40.000 50.000 49.500 65.000 75.000 78.750 108.000 108.000 108.000 135.000 146.250 Sync Polarity (H/V) +/-/-/+ -/-/-/-/-/+/+ +/+ +/+ +/+ -/-/+/+ +/+ +/+ +/+ +/+ -/+
IBM, 640 x 350 IBM, 640 x 480 IBM, 720 x 400 MAC, 640 x 480 MAC, 832 x 624 MAC, 1152 x 870 VESA, 640 x 480 VESA, 640 x 480 VESA, 800 x 600 VESA, 800 x 600 VESA, 800 x 600 VESA, 800 x 600 VESA, 1024 x 768 VESA, 1024 x 768 VESA, 1024 x 768 VESA, 1152 x 864 VESA, 1280 x 960 VESA, 1280 x 1024 VESA, 1280 x 1024 VESA, 1680 x 1050
Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz Vertical Frequency Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz
General Model Name LCD Panel Size 22 inch (55 cm) SyncMaster T220HD
LCD Panel Display area Pixel Pitch Synchronization Horizontal Vertical Display Color 16.2M Resolution Optimum resolution Maximum resolution 1680 x 1050 @ 60 Hz 1680 x 1050 @ 60 Hz 30 ~ 81 kHz 56 ~ 75 Hz 473.76 mm (H) x 296.1 mm (V) 0.282 mm (H) x 0.282 mm (V)
Input Signal, Terminated RGB Analog, DVI(Digital Visual Interface) 0.7 Vp-p 5 % separate H/V sync, Composite TTL level (V high 2.0 V, V low 0.8 V) Maximum Pixel Clock 146.250 MHz (Analog, Digital) Power Supply AC 100 - 240 V~ (+/- 10 %), 50/60 Hz 3 Hz Signal Cable 15pin - to - 15pin D-sub cable, Detachable DVI-D to DVI-D connector, Detachable Dimensions (W x H x D) / Weight 520 x 373.5 x 86.5 mm / 20.5 X 14.7 X 3.4 inch (Without Stand) 520 x 441.5 x 215 mm / 20.5 X 17.4 X 8.5 inch (With Stand) / 6.2 kg / 13.7 Ibs Environmental considerations Operating Temperature : 50 F ~ 104 F (10 C ~ 40 C) Humidity : 10 % ~ 80 %, non-condensing Storage Temperature : -4 F ~ 113 F (-20 C ~ 45 C) Humidity : 5 % ~ 95 %, non-condensing Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor

Avoid using a combination of characters and background color with large difference in luminance. Avoid using Grey colors, which can cause Image retention easily. Avoid: Colors with big difference in luminance (Black & White, Grey) Ex)
Recommended settings: Bright colors with little difference in luminance Change the characters color and background color every 30 minutes Ex)
Every 30 minutes, change the characters with movement. Ex)
The best way to protect your monitor from Image retention is to set your PC or System to operate a Screen Saver program when you are not using it.
Information Image retention may not occur when a LCD panel is operated under normal conditions. Normal conditions are defined as continuously changing video patterns. When the LCD panel is operated for a long time with a fixed pattern (-over 12 hours-), there may be slight difference in voltage between electrodes that work the liquid crystal (LC) in a pixel. The voltage difference between electrodes increases with time, forcing the liquid crystal to lean. When this occurs, the previous image may be seen when the pattern is changed. To prevent this, the accumulated voltage difference must be decreased.
Our LCD Monitor satisfies ISO13406-2 Pixel fault Class II

Appendix

Contact SAMSUNG WORLDWIDE
Note If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. North America U.S.A CANADA MEXICO 1-800-SAMSUNG(726-7864) 1-800-SAMSUNG(726-7864) http://www.samsung.com http://www.samsung.com/ca
01-800-SAMSUNG(726-7864) http://www.samsung.com Latin America

ARGENTINE BRAZIL

0800-333-3733 0800-124-421 4004-0000
http://www.samsung.com/ar http://www.samsung.com
CHILE COLOMBIA COSTA RICA ECUADOR EL SALVADOR GUATEMALA HONDURAS JAMAICA NICARAGUA PANAMA PUERTO RICO REP. DOMINICA
800-SAMSUNG(726-7864) 01-8000112112 0-800-507-7267 1-800-10-7267 800-6225 1-800-299-0013 800-7919267 1-800-234-7267 00-1800-5077267 800-7267 1-800-682-3180 1-800-751-2676
http://www.samsung.com/cl http://www.samsung.com/co http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin

TRINIDAD & TO- 1-800-SAMSUNG(726-7864) BAGO VENEZUELA 0-800-100-5303 Europe AUSTRIA BELGIUM 0800-SAMSUNG (726-7864) 0032 (0)24 18
http://www.samsung.com/at http://www.samsung.com/be http://www.samsung.com/cz

CZECH REPUBLIC 844

DENMARK EIRE FINLAND FRANCE

100 030-6227 515

http://www.samsung.com/dk http://www.samsung.com/ie http://www.samsung.com/fi
3260 SAMSUNG ( 0,15/Min) http://www.samsung.com 65 ( 0,15/Min)
Europe GERMANY HUNGARY ITALIA LUXEMBURG NETHERLANDS NORWAY POLAND 01805 - SAMSUNG (726-7864) http://www.samsung.com ( 0,14/Min) 06-80-SAMSUNG (726-7864) 800-SAMSUNG (726-7864) 0035 (0)http://www.samsung.com http://www.samsung.com http://www.samsung.com/be
0900 SAMSUNG (726-7864 http://www.samsung.com/nl 0,10/Min) 815-022-607-93-33 http://www.samsung.com/no http://www.samsung.com/pl
PORTUGAL SLOVAKIA SPAIN SWEDEN SWITZERLAND U.K
80820-SAMSUNG (726-7864) 0800-SAMSUNG (726-7864) 0771-0800-SAMSUNG (726-7864) 0845 SAMSUNG (7267864) CIS
http://www.samsung.com/pt http://www.samsung.com/sk http://www.samsung.com http://www.samsung.com/se http://www.samsung.com/ch http://www.samsung.com
ESTONIA LATVIA LITHUANIA KAZAKHSTAN KYRGYZSTAN RUSSIA TADJIKISTAN UKRAINE UZBEKISTAN
800-7267 800-7267 8-800-77777 8-10-800-500-55-500 00-800-500-55-500 8-800-555-55-55 8-10-800-500-55-500 8-800-502-0000 8-10-800-500-55-500 Asia Pacific
http://www.samsung.ee http://www.samsung.com/lv http://www.samsung.lt http://www.samsung.kz http://www.samsung.ru http://www.samsung.com http://www.samsung.uz

AUSTRALIA CHINA

603 800-810-5858 010-6475 1880
http://www.samsung.com http://www.samsung.com

HONG KONG INDIA

3698 - 110011
http://www.samsung.com/hk http://www.samsung.com
INDONESIA JAPAN MALAYSIA NEW ZEALAND PHILIPPINES SINGAPORE THAILAND
0800-112-8888 0120-327-527 1800-88-SAMSUNG(726-7864) 1800-SAMSUNG(726-7864) 1800-29-3232, 02-689-3232
http://www.samsung.com http://www.samsung.com/jp http://www.samsung.com/my http://www.samsung.com/nz http://www.samsung.com http://www.samsung.com
1800-10-SAMSUNG(726-7864) http://www.samsung.com/ph

Asia Pacific TAIWAN VIETNAM 0800-329-889 Middle East & Africa SOUTH AFRICA TURKEY U.A.E 0860-SAMSUNG(726-7864) 11 800-SAMSUNG(726-7864) 8000-4726 http://www.samsung.com http://www.samsung.com http://www.samsung.com http://www.samsung.com/tw http://www.samsung.com
Sync Signal Sync (Synchronized) Signals refer to the standard signals that are required to display desired colors on the monitor. They are divided into Vertical and Horizontal Sync Signals. These signals display normal color images by the set resolution and frequency. Separate Composite

Types of Sync Signals

This is a scheme of transmitting individual vertical and hori sync signals to the monitor.
This is a scheme of combining vertical and horizontal syn nals into one composite signal and transmitting it to the mo The monitor displays the color signals by separating the co site signal into original color signals.

Dot Pitch

The image on a monitor is composed of red, green and blue dots. The closer the dots, the higher the resolution. The distance between two dots of the same color is called the 'Dot Pitch'. Unit: mm The screen must be redrawn several times per second in order to create and display an image for the user. The frequency of this repetition per second is called the Vertical Frequency or Refresh Rate. Unit: Hz Example: If the same light repeats itself 60 times per second, this is regarded as 60 Hz.

Vertical Frequency

Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle. The inverse number of the Horizontal Cycle is called Horizontal Frequency. Unit: kHz Showing the horizontal lines of the screen from the top to the bottom sequentially is called the Non-Interlace method while showing odd lines and then even lines in turn is called the Interlace method. The Non-Interlace method is used for the majority of monitors to ensure a clear image. The Interlace method is the same as that used in TVs. This is a function that provides the best quality screen for the user by allowing the computer and the monitor to exchange information automatically. This monitor follows the international standard VESA DDC for the Plug & Play function. The number of horizontal and vertical dots used to compose the screen image is called the 'resolution'. This number shows the ac-

External Device Input

DTV Broadcasting (Digital TV Broadcasting) LNA (Low Noise Amplifier) Antenna Converter English Caption (= Caption Setting)

Multiplex Broadcasting

Appendix A2 BTSC This system uses two carriers to transmit voice data. Countries such as South Korea and Germany use this system. Broadcast Television System CommitteeThe stereo broadcasting system that is used in most of the countries that have adopted the NTSC system, including the United States, Canada, Chile, Venezuela and Taiwan. It also refers to the organization that has been organized to promote its development and management. Electronic Industries Association of Japan. DVI is the acronym for Digital Video Interface. It is a new type of video interface technology that provides the maximum screen quality for high quality display devices and high-end graphics cards including flat panel LCD monitors. This is an interface that connects both quality video signals and digital audio signals with a cable without any compression. HD (High Definition) In HD, 1080-line, 2x density beaming (1080i) is used. HD provides a five times clearer screen quality than the existing analog method and has a wide 16:9 aspect ratio. SD (Standard Definition) In HD, 480-line, double beaming (480i) is used. SD provides a screen quality somewhere between HD and the existing analog method. It exhibits a two times better screen quality than analog TV.

EIAJ DVI

HDMI(High Definition Multimedia Interface)

Correct Disposal

Correct Disposal of This Product (Waste Electrical & Electronic Equipment) Europe only (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.

Authority

Information in this document is subject to change without notice.
Appendix 2008 Samsung Electronics Co., Ltd. All rights reserved. Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly forbidden. Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. Samsung is the registered trademark of Samsung Electronics Co., Ltd.; Microsoft, Windows and Windows NT are registered trademarks of Microsoft Corporation; VESA, DPM and DDC are registered trademarks of Video Electronics Standard Association; the ENERGY STAR name and logo are registered trademarks of the U.S. Environmental Protection Agency (EPA). As an ENERGY STAR Partner, Samsung Electronics Co., Ltd. has determined that this product meets the ENERGY STAR guidelines for energy efficiency. All other product names mentioned herein may be the trademarks or registered trademarks of their respective owners.