If there is a strange smell or a strange sound or smoke is coming from the product, disconnect the power plug immediately and contact a Service Center. Otherwise, this may result in electric shock or fire.
Do not place this product in a location exposed to moisture, dust, smoke, water, or in a car. Otherwise, this may result in electric shock or fire.
When you drop the product or the case is broken, turn the power off and disconnect the power cord. Contact a Service Center. Otherwise, this may result in electric shock or fire.
If thunder or lightening is occurring, do not touch the power cord or antenna cable. Otherwise, this may result in electric shock or fire.
Do not try to move the monitor by pulling only the wire or the signal cable. Otherwise, it may fall and result in electric shock, damage to the product or fire due to damage to the cable.
Do not lift or move the product back and forwards or right and left while only holding the power cord or signal cables. Otherwise, it may fall and result in electric shock, damage to the product or fire due to damage to the cable.
Make sure that the ventilating opening is not blocked by a table or curtain. Otherwise, it may result in fire due to an increase in the internal temperature.
Do not place any containers containing water, vases, flowerpots, medicines as well as any metal on the product. If water or a foreign material enters the product, disconnect the power cord and contact a Service Center. This may result in a product malfunction, electric shock, or fire.
Do not use or keep combustible spray or flammable material near the product. Otherwise, this may result in an explosion or fire.
Do not insert any metal, such as chopsticks, coins, pins and steel, or flammable objects, such as matches or paper, inside the product (through the ventilating openings, input and output terminals, etc). If water or foreign material enters the product, disconnect the power cord and contact a Service Center. Otherwise, this may result in electric shock or fire.
When using a fixed screen for a long time, an afterimage or stain may occur. If you are not using your product for a long period of time, put it into sleep mode or use a moving screen saver. Set a resolution and frequency appropriate to the product. Otherwise, your eyesight may be damaged.
When using headphones or earphones, do not turn the volume too high. Having the sound too loud may damage your hearing.
If you continually move closer to the product screen, your eyesight may be failing.
To ease eye strain, take at least a five-minute break after every hour of using the monitor.
Do not install it in an unstable location such as an unstable rack or uneven surface or a location exposed to vibrations. Otherwise, it may fall and cause personal injury and/or damage the product. If you use the product in a location exposed to vibrations, it may damage the product and result in fire.

Be careful when adjusting the angle of the product or the height of the stand. This may result in personal injury as your hand or fingers may become caught. Also, if you tilt the product too far, it may fall and cause personal injury.
Do not install the product in a location low enough for children to reach. Otherwise, it may fall and result in personal injury. Since the front part of the product is heavy, install the product on a level and stable surface. Do not put any heavy objects on the product. This may result in personal injury and/or damage to the product.
Good Postures When Using the Monitor When using the product, use it in the correct position. Keep your back straight while looking at the product. The distance between your eyes and the screen should be between 45 to 50 cm. Look at the screen from a slightly higher location than the height of the screen. When using the product, use it in the correct position. Adjust the angle so that light is not reflected on the screen. Place your arms perpendicular to your sides and allow your arms to be level with the back of the hand. Keep your elbow at 90 degrees. Keep your knees at greater than 90 degrees, and keep your heels firmly on the floor. Keep your arms lower than your heart.

Introduction

Package Contents
Note Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Contact a local dealer to buy optional items.

Unpacking

Without stand

With stand

Monitor Manuals

Monitor

Quick Setup Guide
Warranty Card (Not available in all locations)

User's Guide

Cables
D-Sub Cable Sold separately

Power Cord

Stereo Cable

DVI Cable

HDMI Cable

Headphones

Sold separately

USB Cable

TV Antenna Cable (Coaxial Cable)
Component(PR, PB, Y) Cable

Audio cable

Digital audio optic output cable
Remote Control BN59-00678A
Batteries (AAA X 2) (Not available in all locations)

Cleaning Cloth

Cable holding ring Note

Stand Body

Stand Base
Cleaning Cloth is only provided for highly polished black products as a product feature.

Your Monitor Front

Activates a highlighted menu item. Push the ' ', button to change the input signal source.
Changing the source is only allowed for external devices connected to the product at the time. To switch Screen modes: [PC] [DVI] [TV] [Component] [HDMI1] [HDMI2] >> Click here to see an animation clip MENU Use this button to open the on-screen menu and to exit from the on-screen menu or to close the screen adjustment menu. - VOL+ Moves from one menu item to another horizontally or adjusts selected menu values. Adjusts the audio volume. - CH + Moves from one menu item to another vertically or adjusts selected menu values. In TV/DTV mode, selects TV/DTV channels. Power button [ ]

Use this button for turning the product on and off.
Note The button to the right of the monitor are touch-sensitive buttons. Touch a button lightly with your finger. Power indicator This light is lit when operating normally, and blinks once when your adjustments are saved. Note See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed or when leaving it unattended for long periods. Speaker
Note The configuration at the back of the product may vary from product to product.
POWER POWER Connect the power cord for your monitor to the POWER port on the back of the product.
PC Connect the PC terminal at the back of your monitor to your computer.
HDMI/PC/DVI-D AUDIO IN DIGITAL AUDIO OUT(OPTICAL) EX-LINK HDMI/PC/DVI-D AUDIO IN Connect the [ HDMI/PC/DVI-D AUDIO IN ] terminal at the back of your product to your computers sound card. DIGITAL AUDIO OUT(OPTICAL) Connect the [DIGITAL AUDIO OUT(OPTICAL)] terminal of your product to the digital sound output or standard sound output terminal of the DVD home theater (or amplifier) using a digital audio optical output cable. EX-LINK This is a reserved terminal used for servicing. SERVICE SERVICE This is a reserved terminal used for servicing.
DVI-D DVI-D Connect the DVI cable to the DVI-D port on the back of your product.

Kensington Lock

The Kensington Lock is a device used to physically fix the system when using it in a public place. The locking device has to be purchased separately. The appearance and locking method may differ from the illustration depending on the manufacturer. Refer to the manual provided with the Kensington Lock for proper use. The locking device has to be purchased separately. Note The location of the Kensington Lock may be different depending on its model.
Using the Anti-Theft Kensington Lock
1. Insert the locking device into the Kensington slot on the Monitor ( locking direction ( 2. 3. HDMI IN 1 HDMI IN 1 Connect the [HDMI IN 1] terminal at the back of your monitor to the HDMI terminal of your digital output device using a HDMI cable. ). ) and turn it in the

10. Click the "Finish" button then the "Close" button. If you can see the "Digital Signature Not Found" window then click the "Yes" button. And click the "Finish" button then the "Close" button. Microsoft Windows Millennium Operating System 1. 2. 3. Click "Start", "Setting", "Control Panel". Double click the "Display" icon. Select the "Settings" tab and click "Advanced Properties" button.
Using the Software 4. 5. 6. 7. 8. 9. Select the "Monitor" tab. Click the "Change" button in the "Monitor Type" area. Choose "Specify the location of the driver". Choose "Display a list of all the driver in a specific location." then click "Next" button. Click the "Have Disk" button. Specify A:\(D:\driver) then click "OK" button.
10. Select "Show all devices" and choose the monitor that corresponds to the one you connected to your computer and click "OK". 11. Continue choosing "Close" button and "OK" button until you close the Display Properties dialogue box. Microsoft Windows NT Operating System 1. 2. 3. 4. Click "Start", "Settings", "Control Panel", and then double-click "Display" icon. In Display Registration Information window, click Settings Tab and then click "All Display Modes". Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and then click "OK". Click "Apply" button if you see the screen working normally after clicking "Test". If the screen is not normal, change to a different mode (lower mode of resolution, colors or frequency). Note If there is no Mode at All Display Modes, select the level of resolution and vertical frequency by referring to the Preset Timing Modes in the user guide. Linux Operating System To execute X-Window, you need to make the X86Config file, which is a type of system setting file. 1. 2. 3. 4. 5. 6. 7. 8. 9. Press "Enter" at the first and the second screen after executing the X86Config file. The third screen is for setting your mouse. Set a mouse for your computer. The next screen is for selecting a keyboard. Set a Keyboard for your computer. The next screen is for setting your monitor. First of all, set a horizontal frequency for your monitor. (You can enter the frequency directly.) Set a vertical frequency for your monitor. (You can enter the frequency directly.) Enter the model name of your monitor. This information will not affect the actual execution of X-Window.

Adjusting the Monitor Dynamic Contrast automatically detects the distribution of the visual signal and adjusts to create an optimum contrast. Custom Although the values are carefully chosen by our engineers, the pre-configured values may not be comfortable to your eyes depending on your taste. If this is the case, adjust the Brightness and Contrast by using the OSD menu. MENU , MENU,EXIT
Contrast / Brightness / Sharpness
(Not available in MagicBright mode of Dynamic Contrast.)
You can use the on-screen menus to change the contrast and brightness according to personal preference. Contrast : Adjust the Contrast. Brightness : Adjust the Brightness. Sharpness : Adjust the Sharpness. , , , , MENU,EXIT

Auto Adjustment

The values of Fine, Coarse and Position are adjusted automatically.
Adjusting the Monitor By changing the resolution in the control panel, auto function is performed. (Available in PC Mode Only) MENU , MENU,EXIT
Screen : (Available in PC mode only) - Coarse / Fine
Coarse Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may relocate it to the center using the horizontal control menu.
Fine Removes noise such as horizontal stripes. If the noise persists even after Fine tuning, repeat it after adjusting the frequency (clock speed).

MENU,EXIT

- Position
Adjusts the screen location horizontally and vertically. MENU , , , , , MENU,EXIT

- Image Reset

Image parameters are replaced with the factory default values. MENU , , MENU,EXIT

- Resolution

Displays the resolution set on the PC.
Picture Options - Color Tone
Adjusting the Monitor The tone of the color can be changed. (Available in PC / DVI mode only) Cool / Normal / Warm / Custom MENU , , MENU,EXIT
- R-Gain / G-Gain / B-Gain
Adjusts the individual R, G, B color controls. MENU , , , , , MENU,EXIT

- Size

You can switch the Size. Wide / 4:3 MENU , , , MENU,EXIT
Picture parameters are replaced with the factory default values. OK Cancel , , MENU,EXIT
Picture : TV / Component / HDMI Mode
The Monitor has three automatic picture settings ("Dynamic", "Standard", and "Movie") that are preset at the factory. You can activate either Dynamic, Standard, or Movie. Dynamic Selects the picture for high-definition in a bright room. Standard Selects the picture for optimum display in a normal environment. Movie Selects the picture for viewing movies in a dark room.
Backlight / Contrast / Brightness / Sharpness / Color / Tint

The Monitor has a built-in high fidelity stereo amplifier. Standard Choose Standard for the standard factory settings. Music Choose Music when watching music videos or concerts. Movie Choose Movie when viewing movies. Speech Choose Speech when watching a show that is mostly dialogue (i.e., news). Custom Choose Custom if you want to adjust the settings according to personal preference. MENU , , MENU,EXIT

Equalizer

You can adjust the left and right sound balance and the low or high volume as required. MENU , , , , , MENU,EXIT
Multi-Track Options Preferred Language
You can select the audio language. (Available in DTV Mode Only) MENU , , , MENU,EXIT

Multi-Track Sound

Mono : Choose for channels that are broadcasting in mono or if you are having difficulty receiving a stereo signal. Stereo : Choose for channels that are broadcasting in stereo. SAP : Choose to listen to the Separate Audio Program, which is usually a foreign-language translation.
(Available in Analog TV Mode Only) MENU , , , MENU,EXIT

Auto Volume

Reduces the differences in volume level among broadcasters. Off On , , , MENU,EXIT

TV Speaker

If you set this menu "On", sound output from the speakers is muted in case of using the home theater. Off On , , , MENU,EXIT

Channel Available Modes

PC / DVI TV Component HDMI Note The default setting may different depending on the selected Input Mode (input signal source selected in External Input List) and the selected resolution.

Antenna

Adjusting the Monitor You can select a normal or wired channel. If ANT IN are connected, select the antenna input you want. If the antenna input is not selected properly, noise may appear on the screen. Air Cable , , MENU,EXIT

Auto Program

The TV automatically cycles through all of the available channels and stores them in memory. In rare cases, "Auto program" may miss a few channels due to weak signals and the channels may not be added to the channel memory. Air Cable Auto , , , , , , MENU,EXIT

Clear Scrambled Channel

Adjusting the Monitor The Clear Scrambled Channel function is used to filter out scrambled channels after "Auto Program" is completed. It removes the scrambled channels from the list by tuning the digital cable channels. This process may take up to 20~30 minutes. (Available in Digital Cable TV Mode Only) MENU , , MENU,EXIT

Channel List

You can manage the channels.

MENU , MENU,EXIT

Note All selected channels will be shown on Added menu. , , , ,

MENU , MENU,EXIT

Favorite
Note Only memorized channels can be set as favorite channels. All favorite channels will be shown in the Favorite menu. , , , ,
If channel name information is broadcast when you store the channels either manually or automatically, the names are assigned to the channels directly. You can however change these names or assign new names as required. (Available in Analog TV Mode Only) MENU , , , , , , , MENU,EXIT

Fine Tune

Due to weak signals or an incorrect antenna configuration, some of the channels may not be tuned correctly. (Available in Analog TV Mode Only) MENU , , , , MENU,EXIT

Signal Strength

Unlike analog channels, which can vary in reception quality from "snowy" to clear, digital (HDTV) channels have either perfect reception quality or you will not receive them at all. So, unlike analog channels, you cannot fine tune a digital channel. You can, however, adjust your antenna to improve the reception of available digital channels. If the signal strength meter indicates that the signal is weak, physically adjust your antenna to increase the signal strength. Continue to adjust the antenna until you find the best position with the strongest signal. (Available in Digital Cable TV Mode Only) MENU , , MENU,EXIT

Setup Available Modes

Plug & Play
You can manage the entire configuration. MENU , , , , , MENU,EXIT , , , , ,

Language

You can choose one of 3 languages.
The language chosen affects only the language of the OSD. MENU , , MENU,EXIT

Time Clock

You can set the current time.

- Clock Mode

Auto / Manual MENU , , , MENU,EXIT

- Clock Set

Note Clock Set are available only when Clock Mode set to Manual. MENU , , , , , , MENU,EXIT

- Time Zone

Note Time Zone are available only when Clock Mode set to Auto. MENU , , , , MENU,EXIT
Note DST are available only when Clock Mode set to Auto. Depending on the broadcast station and signal, the auto time may not be set correctly. If this occurs, set the time manually. The Antenna or cable must be connected in order to set the time automatically. , , , , MENU,EXIT

Sleep Timer

Use to set the Monitor to be turned off automatically in certain minutes. Off, 30, 60, 90, 120, 150, 180 , , , , , , MENU,EXIT

Timer1 / Timer2 / Timer3

You can set the monitor to be turned on or off automatically at a specified time. Note Setting the clock is necessary in order to use the various timer features of the product. Three different On/Off Timer Settings can be made. MENU , , , , , , MENU,EXIT

Check List

Note Before calling for assistance, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer.
1. Problems related to Installation
Note Problems related to the monitor installation and their solutions are listed.

PC Mode

Q: A: Q: A: It appears the PC does not function normally. Check if the Display Adapter Driver (VGA Driver) is properly installed. (Refer to Installing Driver) The monitor screen flickers. Check if the signal cable between the computer and the monitor is securely connected and tightened.(Refer to Connecting the monitor)

TV Mode

Q: A: Q: A: TV screen is blurred or shows noise signals. Check if the TV antenna connector is securely connected to the external antenna.(Refer to Connecting TV) TV signal is not received Select "Auto Program" to configure the channel system automatically. (Refer to the Auto Program)
2. Problems related to Screen
Note Problems related to the monitor screen and their solutions are listed. Q: A: Q: A: A: Q: A: A: Q: A: Q: A: A: A: Screen is blank and power indicator is off Ensure that the power cord is firmly connected and the LCD monitor is on.(Refer to the Connecting the monitor) "Check Signal Cable" message Ensure that the signal cable is firmly connected to the PC or video SOURCEs.(Refer to the Connecting the monitor) Ensure that the PC or video SOURCEs are turned on. "Not Optimum Mode" message Check the maximum resolution and the frequency of the video adapter. Compare these values with the data in the Preset Timing Modes Chart. Picture rolls vertically. Check if the signal cable is securely connected.Connect it again securely. (Refer to Connecting the monitor) Image is not clear. Picture is blurred. Run Frequency Coarse and Fine tuning. Turn on again after removing all accessories (video extension cable, etc.) Set resolution and frequency to the recommended ranges.
Troubleshooting Q: Picture image is unstable and vibrates. Ghost images are shown in the picture. A: Check if the resolution and frequency set for the computer video card falls in the range supported by the monitor.If not, reset them referring to the current Information under the monitor menu and Preset Timing Modes. The image is too light or too dark Adjust the Brightness and Contrast.(Refer to the Brightness, Contrast) The Power Indicator blinks. The monitor is currently saving the changes made in settings to the OSD memory. The screen is blank and the power indicator light blinks every 0.5 or 1 seconds. The monitor is using its power management system. press a key on the keyboard. The screen is blank and is blinking. If you see the "TEST GOOD" message on the screen when you press the MENU button, check the cable connection between the monitor and the computer to ensure that the connector is properly connected.

Troubleshooting specific scene. In addition, you can retrive information on a previous story or drama or you can buy home shopping products such as an accessory currently on TV. Digital TV broadcasting allows you to easily access various information services in your home creating a more information-oriented home. Q: A: A: What is the difference between HDTV and SDTV? There are various types of digital TVs. The most widely known types of digital TV are HDTV and SDTV. They are classified according to the screen quality and the video specifications. A: HDTV (High Definition TV): High screen quality, very clear TV. SDTV (Standard Definition TV): Common standard digital TV.
An SDTV has an aspect ratio of 4:3 which is the same as that of an analog TV. SDTV has an aspect ratio of 16:9 which is similar to a cinema screen. This provides a much better screen quality than SDTV. It's like having a theater in your home. Digital TV broadcasting in our country is ultimately orientated towards HDTV. Can I watch HD broadcasting with all digital TVs? You can receive all digital broadcasts, whether they are SD or HD, using any digital TV. However, you cannot enjoy HD programs, which are the highest quality digital TV programs, using an SD digital TV. Especially, as SD broadcasting has an aspect ratio of 4:3, HD broadcasting has an aspect ratio of 16:9, similar to a cinema screen. Therefore, to enjoy the full benefits of digital TV, it is better to purchase an HD digital TV. (At present, all digital TVs from Samsung Electronics have the 16:9 wide aspect ratio.)

A: Q: A:

Q: A: A: Q: A: A: Q: A: A:
Can I watch digital TV broadcasting with an analog TV? No. The analog TV cannot interpret digital signals. Therefore, a digital TV is required to watch digital TV broadcasting. Can I use my present antenna to receive digital broadcasting? As for existing analog TV, digital TV is designed so that digital broadcasting signals are received via both indoor and outdoor antennas. If signal reception is very good in your environment, you can watch digital broadcasts with your existing indoor antenna. If not, it is better to install an outdoor UHF antenna. How do I connect an antenna for an apartment or tenement house? Consult the superintendent's office or broadcasting facility administrator for your apartment or tenement house to check whether UHF reception is available. Even if digital TV broadcasting is available in your area, if you cannot watch it because the superintendent's office or common broadcasting facility does not rebroadcast the signal, you have to install an indoor or outdoor antenna. Alternatively, your local cable broadcasting company provides a digital TV service, and you can subscribe to it.

IBM, 640 x 350

Display Mode
Horizontal Frequency (kHz) 31.469 31.469 35.000 49.726 68.681 37.861 37.500 35.156 37.879 48.077 46.875 48.363 56.476 60.023 67.500 60.000 63.981 79.976 65.290
Vertical Frequency (Hz) 59.940 70.087 66.667 74.551 75.062 72.809 75.000 56.250 60.317 72.188 75.000 60.004 70.069 75.029 75.000 60.000 60.020 75.025 59.954
Pixel Clock (MHz) 25.175 28.322 30.240 57.284 100.000 31.500 31.500 36.000 40.000 50.000 49.500 65.000 75.000 78.750 108.000 108.000 108.000 135.000 146.250
Sync Polarity (H/V) -/-/+ -/-/-/-/-/+/+ +/+ +/+ +/+ -/-/+/+ +/+ +/+ +/+ +/+ -/+
IBM, 640 x 480 IBM, 720 x 400 MAC, 640 x 480 MAC, 832 x 624 MAC, 1152 x 870 VESA, 640 x 480 VESA, 640 x 480 VESA, 800 x 600 VESA, 800 x 600 VESA, 800 x 600 VESA, 800 x 600 VESA, 1024 x 768 VESA, 1024 x 768 VESA, 1024 x 768 VESA, 1152 x 864 VESA, 1280 x 960 VESA, 1280 x 1024 VESA, 1280 x 1024 VESA, 1680 x 1050

Information

For Better Display
Adjust the computer resolution and screen injection rate (refresh rate) on the computer as described below to enjoy the best picture quality. You can have an uneven picture quality on screen if the best picture quality is not provided for TFT-LCD. Resolution: 1680 x 1050 Vertical frequency (refresh rate): 60 Hz
TFT-LCD panels manufactured by using advanced semiconductor technology with a precision of 1ppm (one millionth) and above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality and you can use it without any problems. For example, the number of TFT-LCD sub pixels contained in this product are 5,292,000.
When cleaning the monitor and the panel outside, please apply the recommended small amount of cleaner by using a soft cloth to polish. Do not force the LCD area but rub softly. If excessive force is applied, you may stain it. If you are not satisfied with the picture quality, you can get better quality of picture by performing the "Auto Adjustment function" in display screen that is appeared as window termination button is pressed. If there's still noise after the automatic adjustment, use the Fine/Coarse adjustment function. When viewing a fixed screen for an extended period of time, a residual image or blurriness may appear. Change the mode to energy save or set a screensaver to move the picture when you need to be away from the monitor for an extended period of time. Do not display a still image( such as on a video game or when hooking up a DVD to this LCD_TV ) on the Color TFT-LCD ( Thin Film Transister Liquid Crystal Display) panel for a long time as it can cause screen image retention. This image retention is also known as "screen burn". To avoid such image retention, reduce the degree of brightness and contrast of this screen when displaying a still image. Watching Digital Broadcasting Correctly Digital 16:9 HD Broadcasting Screen Digital SD Broadcasting Screen Digital 4:3 Broadcasting Screen

This screen is shown when This screen is shown when This screen is shown when scenes are captured using dig- scenes are converted to ana- scenes created via analog sigital broadcasting equipment log broadcasting signals benals are displayed while fore being sent. Humans and
Information and they are sent in HDTV objects appear heavier than in watching HDTV broadcast(16:9) mode. reality. ing. Note If temporary stops, mosaic screens, or jagged screens occur, this is not a TV problem. Contact your cable broadcasting company for a check-up. For information on how to connect and use your video, DVD, DVD combo, home theater, PC, etc., refer to their respective user manuals.
PRODUCT INFORMATION (Image Retention Free)
LCD Monitors and TVs may have image retention when switching from one image to another especially after displaying a stationary image for a long time. This guide is to demonstrate correct usage of LCD products in order to protect them from Image retention. Warranty Warranty does not cover any damage caused by image retention. Burn-in is not covered by the warranty. What is Image retention ? During normal operation of a LCD panel, pixel image retention doesn't occur. However, if the same image is displayed for a long time, a slight difference in electric charge accumulates between the two electrodes which encase the liquid crystal. This may cause the liquid crystal to build up in a certain areas of the display. Thus, the previous image is retained when switching to a new video image. All display products, including LCD, are subject to image retention. This is not a product defect. Please follow the suggestions below to protect your LCD from image retention.
Power Off, Screen Saver, or Power Save Mode Ex) Turn the power off when using a stationary pattern. Turn the power off for 4 hours after 20 hours in use Turn the power off for 2 hours after 12 hours in use
Use a Screen saver if possible Screen saver in one color or a moving image is recommended.
Set the Monitor to power off with the PC Display Properties Power Scheme. Suggestions for specific applications
Ex) Airports, Transit Stations, Stock Markets, Banks, and Controlling Systems We recommend that you follow set up of your display system program as below: Display Information together with Logo or Moving image cycle.
Information Ex) Cycle : Display Information for 1 hour followed by a Display Logo or moving image for 1 minute. Change the Color Information periodically (Use 2 different colors). Ex) Rotate the Color Information with 2 colors every 30 minutes.

Avoid using a combination of characters and background color with large difference in luminance. Avoid using Grey colors, which can cause Image retention easily. Avoid: Colors with big difference in luminance (Black & White, Grey) Ex)
Recommended settings: Bright colors with little difference in luminance Change the characters color and background color every 30 minutes Ex)
Every 30 minutes, change the characters with movement. Ex)
The best way to protect your monitor from Image retention is to set your PC or System to operate a Screen Saver program when you are not using it.
Information Image retention may not occur when a LCD panel is operated under normal conditions. Normal conditions are defined as continuously changing video patterns. When the LCD panel is operated for a long time with a fixed pattern (-over 12 hours-), there may be slight difference in voltage between electrodes that work the liquid crystal (LC) in a pixel. The voltage difference between electrodes increases with time, forcing the liquid crystal to lean. When this occurs, the previous image may be seen when the pattern is changed. To prevent this, the accumulated voltage difference must be decreased.
Our LCD Monitor satisfies ISO13406-2 Pixel fault Class II

Appendix

Contact SAMSUNG WORLDWIDE
Note If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. North America U.S.A CANADA MEXICO 1-800-SAMSUNG(726-7864) 1-800-SAMSUNG(726-7864) http://www.samsung.com http://www.samsung.com/ca
01-800-SAMSUNG(726-7864) http://www.samsung.com Latin America

ARGENTINE BRAZIL

0800-333-3733 0800-124-421 4004-0000
http://www.samsung.com/ar http://www.samsung.com
CHILE COLOMBIA COSTA RICA ECUADOR EL SALVADOR GUATEMALA HONDURAS JAMAICA NICARAGUA PANAMA PUERTO RICO REP. DOMINICA
800-SAMSUNG(726-7864) 01-8000112112 0-800-507-7267 1-800-10-7267 800-6225 1-800-299-0013 800-7919267 1-800-234-7267 00-1800-5077267 800-7267 1-800-682-3180 1-800-751-2676
http://www.samsung.com/cl http://www.samsung.com/co http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin

External Device Input

DTV Broadcasting (Digital TV Broadcasting) LNA (Low Noise Amplifier) Antenna Converter English Caption (= Caption Setting)

Multiplex Broadcasting

Appendix A2 BTSC This system uses two carriers to transmit voice data. Countries such as South Korea and Germany use this system. Broadcast Television System CommitteeThe stereo broadcasting system that is used in most of the countries that have adopted the NTSC system, including the United States, Canada, Chile, Venezuela and Taiwan. It also refers to the organization that has been organized to promote its development and management. Electronic Industries Association of Japan. DVI is the acronym for Digital Video Interface. It is a new type of video interface technology that provides the maximum screen quality for high quality display devices and high-end graphics cards including flat panel LCD monitors. This is an interface that connects both quality video signals and digital audio signals with a cable without any compression. HD (High Definition) In HD, 1080-line, 2x density beaming (1080i) is used. HD provides a five times clearer screen quality than the existing analog method and has a wide 16:9 aspect ratio. SD (Standard Definition) In HD, 480-line, double beaming (480i) is used. SD provides a screen quality somewhere between HD and the existing analog method. It exhibits a two times better screen quality than analog TV.

EIAJ DVI

HDMI(High Definition Multimedia Interface)

Correct Disposal

Correct Disposal of This Product (Waste Electrical & Electronic Equipment) Europe only (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.

Authority

Information in this document is subject to change without notice.
Appendix 2008 Samsung Electronics Co., Ltd. All rights reserved. Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly forbidden. Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. Samsung is the registered trademark of Samsung Electronics Co., Ltd.; Microsoft, Windows and Windows NT are registered trademarks of Microsoft Corporation; VESA, DPM and DDC are registered trademarks of Video Electronics Standard Association; the ENERGY STAR name and logo are registered trademarks of the U.S. Environmental Protection Agency (EPA). As an ENERGY STAR Partner, Samsung Electronics Co., Ltd. has determined that this product meets the ENERGY STAR guidelines for energy efficiency. All other product names mentioned herein may be the trademarks or registered trademarks of their respective owners.

Pre-Release

Samsung SyncMaster 225UW
For Microsoft Office Communicator 2007
The Samsung SyncMaster 225UW is a 22-inch widescreen LCD monitor that uses Microsofts unified communications solutions to streamline all communication functions into a single platform, offering end users a simplified experience that ultimately drives workplace productivity, increases security and reduces costs.
Communications Made Simple
With Microsofts unified communications software package, the SyncMaster 225UW monitor is enabled to integrate all communications systems, from e-mail and instant messaging to Smartphone and VoIP, all of which can be accessed with a single password and log-in. Whether communicating across cubicles or across continents, the SyncMaster 225UW facilitates a top-quality audio and visual communication experience. Equipped with a built-in 2.0M pixel high-resolution webcam, dual-array microphone and speakers, the SyncMaster 225UW is an ideal choice for trueto-life Web conferencing, thereby reducing the need for frequent business travel and decreasing long distance phone costs. The SyncMaster 225UW supports Microsofts presence management features, which lets
users know which of their colleagues are available at any given time and will be automatically routed to the correct communication device, thereby saving time and ultimately driving productivity. With the 225UW, communication is not only simplified, it is also secure. By utilizing the proven stability of Microsoft Exchange Server and Microsoft Office Live Communications Server, IT professionals are given the full peace of mind of universal communications security. In addition to its unified communications capabilities, the SyncMaster 225UW widescreen monitor has qualified for Microsofts Windows Vista Premium Certification, therefore ensuring the full range of features and benefits of a Windows Vista operating system.
22-inch widescreen monitor offers sleek design, high-end features
The SyncMaster 225UW provides premium performance, value and style. With a high resolution of 1680 x 1050, coupled with a wide 16:10 aspect ratio, the SyncMaster 225UW offers superior image quality and enhanced productivity for a range of professional applications. Featuring a 5ms response time, a 700:1 contrast ratio and 300cd/m2 brightness, the model is equipped to produce crisp, true-to-life images, while the wide 170/160 viewing angle further enhances the overall viewing experience. The monitor also incorporates a 2 port USB hub and dual inputs (DVI-D & Analog). The widescreen monitor is packaged in a sleek design, with a high-gloss shiny black bezel and a stylish square-based stand. The monitor also features a set of touch-sensitive buttons, enhancing overall ease-of-use and adding an ultra-modern feel.
The SyncMaster 225UW will be available in June for an MSRP of $449.99. Like all Samsung displays, the SyncMaster 225UW is backed by a three-year limited warranty on labor and parts, including the backlight, as well as toll-free technical support for the life of the display.
Samsung Electronics America
3351 Michelson Drive Suite 250 Irvine, CA 92612 (T) 1-800-Samsung www.samsung.com