SyncMaster 245B / 245BW

Install driver

Notation

Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment.

Prohibited

Important to read and understand at all times

Do not disassemble

Disconnect the plug from the outlet

Do not touch

Ground to prevent an electric shock
When not used for extended period of time, set your computer to DPMS. If using a screen saver, set it to active screen mode. The images here are for reference only, and are not applicable in all cases (or countries).
Do not use a damaged or loose plug.
This may cause electric shock or fire.
Do not pull the plug out by the wire nor touch the plug with wet hands. This may cause electric shock or fire.
Use only a properly grounded plug and receptacle. An improper ground may cause electric shock or equipment damage. (Class l Equipment only.)
Insert the power plug firmly so that it does not come loose. A bad connection may cause fire.
Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage. This may cause electric shock or fire.
Do not connect too many extension cords or plugs to one outlet. This may cause fire.
Do not disconnect the power cord while using the monitor. A surge may be caused by the separation and may damage the monitor.
Do not use the power cord when the connector or plug is dusty. If the connector or plug of the power cord is dusty, clean it with a dry cloth. Using the power cord with a dusty plug or connector may cause electric shock or fire.
To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the mains plug shall be readily operable.

Installation

Be sure to contact an authorized Service Center when installing your set in a location with heavy dust, high or low temperatures, high humidity, and exposed to chemical substances and where it will be operated for 24 hours continuously such as at airports, train stations etc. Failure to do so may cause serious damage to your monitor. Place your monitor in a location with low humidity and a minimum of dust. Failure to do so may cause electric shock or fire inside the monitor.
Do not drop the monitor when moving it. This may cause damage to the product or the person carrying it.
Install the monitor base in a showcase or shelf so that the end of the base does not protrude from the showcase or shelf. Dropping the product may cause damage to the product or the person carrying it.
Do not place the product on an unstable or small surface area. Place the product on an even and stable surface, as the product may fall and cause harm to someone walking by, specifically children.
Do not place the product on the floor. Take care, as someone, specifically children may trip over it.
TO PREVENT THE SPREAD OF FIRE, KEEP CANDLES OR OTHER OPEN FLAMES AWAY FROM THIS PRODUCT AT ALL TIMES. Otherwise, this may cause fire.

If the monitor is dropped or the casing is damaged, turn the monitor off and unplug the power cord. Then contact the Service Center. The monitor may malfunction, causing electric shock or fire.
Disconnect the plug from the outlet during storms or lightning or if it is not used for a long period of time. Failure to do so may cause electric shock or fire.
Do not try to move the monitor by pulling only the wire or the signal cable. This may cause a breakdown, electric shock or fire due to damage to the cable.
Do not move the monitor right or left by pulling only the wire or the signal cable. This may cause a breakdown, electric shock or fire due to damage to the cable.
Do not cover the vents on the monitor cabinet. Bad ventilation may cause a breakdown or fire.
Do not place water containers, chemical products or small metal objects on the monitor.
This may a malfunction, an electric shock or fire. If a foreign substance enters the monitor, unplug the power cord and contact the Service Center.
Keep the product away from combustible chemical sprays or inflammable substances. This may cause an explosion or fire.
Never insert anything metallic into the monitor openings. This may cause electric shock, fire or injury.
Do not insert metal objects such as chopsticks, wire and tools or inflammable objects such as paper or matches into the vent, headphone port or AV ports or etc or etc. This may cause electric shock or fire. If an alien substances or water enters the product, turn the product off, unplug the power connector from the wall outlet and contact the Service Center.
When viewing a fixed screen for an extended period of time, residual image or blurriness may appear. Change the mode to energy saving mode or set a screensaver to a changing picture when away from the monitor for an extended period of time.
Adjust the resolution and frequency to the level appropriate for the model. An inappropriate resolution may cause undesirable picture quality. 24 inch Wide (61 cm) - 1920 x 1200
Viewing the monitor continuously at a too close angle may result in damage to your eyesight.
To ease eye strain, take at least a five-minute break after every hour of using the monitor.
Do not install the product on an unstable, uneven surface or a location prone to vibrations.
Dropping the product may cause damage to the product or the person carrying it. Using the product in a location prone to vibrations may shorten the lifetime of the product or may cause the product to catch fire.
When moving the monitor, turn off and unplug the power cord. Make sure that all cables, including the antenna cable and cables connected to other devices, are disconnected before moving the monitor. Failure to disconnect cables may damage it and cause fire or electric shock.

Place the product out of childrens reach, as they could damage by hanging onto it. A falling product may cause injury to the person or even fatality.
When not using the product for an extended period of time, keep the product unplugged. Otherwise, this may cause heat emission from the accumulated dirt or degraded insulation, causing electric shock or fire.
Do not place your children's favorite toys or any other objects of interest on the product. Children may try to climb on the product to retrieve an object. The product could fall, causing injury or even fatality.
When lifting up or moving the monitor, do not lift the monitor upside down while holding only the stand. This may cause your monitor to fall, and become damaged or cause personal injury.
Good Postures When Using the Monitor
Try to maintain a good posture when using the monitor. Keep your back straight. Keep a distance of about 45 ~ 50 cm between your eyes and the monitor screen. Look at the screen from slightly above it, and have the monitor directly in front of you. Tilt the monitor upwards by 10 ~20 degrees. Adjust the monitor height so that the top of the monitor is slightly below eye level. Adjust the monitor angle so that there is no reflected light on the screen.Try to maintain your arms perpendicular to your armpits. Keep your arms level with the back of your hands. Keep the angle of the elbow perpendicular. Keep the angle of the knees at more than 90 degree. Do not let your
feet fall up from the floor. Adjust the arm position so that it is below the heart
Correct Disposal of This Product (Waste Electrical & Electronic Equipment) - Europe only
(Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.
PRODUCT INFORMATION (Image Retention Free)
LCD Monitors and TVs may have an image retention when switching from one image to another especially after displaying a stationary image for a long time. This guide is to demonstrate a correct usage of LCD products in order to protect them from Image retention. Warranty Warranty does not cover any damage caused by image retention. Burn-in is not covered by the warranty. What is Image retention ? During normal operation of a LCD panel, pixel image retention doesn't occur. However, if the same image is displayed for a long time, a slight difference in electric charge accumulates between the two electrodes which encase the liquid crystal. This may cause the liquid crystal to build up in a certain areas of the display. Thus, the previous image is retained when switching to a new video image. All display products, including LCD,are subject to image retention. This is not a product defect. Please follow the suggestions below to protect your LCD from image retention Power Off, Screen Saver, or Power Save Mode Ex) Turn the power off when using a stationary pattern. - Turn the power off for 4 hours after 20 hours in use - Turn the power off for 2 hours after 12 hours in use Use a Screen saver if possible - Screen saver in one color or a moving image is recommended. Set the Monitor to power off with the PC Display Properties Power Scheme. Suggestions for specific applications Ex) Airports, Transit Stations, Stock Markets, Banks, and Controlling Systems We recommend that you follow set up of your display system program as below: Display Information together with Logo or Moving image cycle. Ex) Cycle : Display Information for 1 hour followed by a Display Logo or moving image for 1 minute. Change the Color Information periodically (Use 2 different colors). Ex) Rotate the Color Information with 2 colors every 30 minutes.

Connecting a Speaker

When connecting a speaker, be careful that the grooves of the monitor and the speaker. ( )are aligned with each other. Adjust the aligned positions until you hear a click. If a speaker is connected correctly, you can hear a click.If a speaker is connected without you hearing a click, the holding part may become damaged. If you need to separate, please pull ( ) a little and push to the right.
MIC / SPK Connect the red cable of the cables provided when the speaker was purchased to the audio output terminal at the back of the computer. Connect the other end of the cable to the red terminal at the back of the speaker. Connect the light green cable of the cables provided when purchasing the speaker to the audio output terminal at the back of the computer. Connect the other end of the cable to the light green terminal at the back of the speaker. / Connect a headphone to the black terminal at the right of the speaker. Connect a microphone to the red terminal at the right of the speaker. By turning part ( + , - ) in the direction shown in the figure below, the speaker turns on and the volume increases.
Connect the power line connected to the speaker to the black terminal of the monitor. This speaker is not connected to an external power source. It is connected to a monitor for the required power.

Using the Stand

Sliding stand

Stand Stopper

Swivel stand
Using ( ),You can swivel the monitor left and right at an angle of 90 to set the monitor lengthwise. The rubber under the stand is to avoid the monitor slide. When you try to rotate the monitor in the state of the power cord or cable connecting to the monitor, the power cord of cable can be destroyed.

Tilt angle

Using ( ), You can adjust the tilt anlgle within a range of 3 forward to 25 backward for the most comfortable viewing angle.
Attaching a Base This monitor accepts a 200 mm x 100 mm VESA-compliant Mounting interface pad.
Monitor Mounting interface pad (Sold separately)

1. 2. 3. 4.

Click the "Close" button then click the "OK" button continually.
Microsoft Windows 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. Choose the "OK" button on the "Insert disk" window. Click the "Browse" button on the "File Needed" window. Choose A:(D:\Driver) then click the "Open" button and then click the "OK" button.
How to install Click "Start," "Setting," and then "Control Panel." Double click the "Display" icon. Select the "Settings" tab and click the "Advanced Properties" button. Choose "Monitor." Case1 : If the "Properties" button is inactive, it means your monitor is properly configured. Please stop installation Case2 : If the "Properties" button is active, click the "Properties" button then follow next steps continually. Click "Driver" and then click "Update Driver." then click the "Next" button. Choose "Display a list of the known drivers for this device so that I can choose a specific driver" then click "Next" and then click "Have disk". Click the "Browse" button then choose A:(D:\Driver). Click the "Open" button, then click the "OK" button. Choose your monitor model and click the "Next" button then click "Next" button. Click the "Finish" button then the "Close" button. If you can see the "Digital Signature Not Found" window then click the "Yes" button. And click the "Finish" button then the "Close" button.
Microsoft Windows Millennium Operating System Click "Start," "Setting," and then "Control Panel." Double click the "Display" icon. Select the "Settings" tab and click the "Advanced Properties" button. Select the "Monitor" tab. Click the "Change" button in the "Monitor Type" area. Choose "Specify the location of the driver." Choose "Display a list of all the driver in a specific location." then click the "Next" button. Click the "Have Disk" button. Specify A:\(D:\driver) then click the "OK" button. Select "Show all devices" and choose the monitor that corresponds to the one you connected to your computer and click "OK". Continue choosing "Close" button and "OK" button until you close the Display Properties dialogue box.

Microsoft Windows NT Operating System Click "Start," "Settings," "Control Panel," and then double-click the "Display" icon. In the Display Registration Information window, click the Settings tab and then click "All Display Modes". Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and then click "OK". Click the "Apply" button if you see the screen working normally after clicking "Test". If the screen is not normal, change to a different mode (lower mode of resolution, colors, or frequency). If there is no Mode at All Display Modes, select the level of resolution and vertical frequency by referring to the Preset Timing Modes in the user guide.
Linux Operating System To execute X-Window, you need to make the X86Config file, which is a type of system setting file. Press "Enter" at the first and the second screen after executing the X86Config file. The third screen is for setting your mouse. Set a mouse for your computer. The next screen is for selecting a keyboard. Set a Keyboard for your computer. The next screen is for setting your monitor. First of all, set a horizontal frequency for your monitor. (You can enter the frequency directly.) Set a vertical frequency for your monitor. (You can enter the frequency directly.) "Enter" the model name of your monitor. This information will not affect the actual execution of XWindow. You have finished setting up your monitor. Execute X-Window after setting other requested hardware.

Control Buttons

[ ] Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu. [ ] These buttons allow you to adjust items in the menu. [ ] Press this button to activate a highlighted menu item. [AUTO] When the 'AUTO' button is pressed, the Auto Adjustment screen appears as shown in the animated screen on the center.

Direct Functions

Description When the 'AUTO' button is pressed, the Auto Adjustment screen appears as shown in the animated screen on the center. Auto adjustment allows the monitor to self-adjust to the incoming Analog signal. The values of fine, coarse and position are adjusted automatically. (Available in Analog mode only) To make the automatic adjustment function sharper, execute the 'AUTO' function while the AUTO PATTERN is on. If auto adjustment does not work properly, press 'AUTO' button again to adjust picture with more accuracy. If you change resolution in the control panel, auto function will be executed automatically.
OSD Locked & Unlock When pressing the AUTO button after locking the OSD
When pressing the MENU button after locking the OSD
Description This is the function that locks the OSD in order to keep the current states of settings or prevent others from adjusting the current settings. Locked : Hold down the menu button for more than five seconds to activate the OSD adjustment lock function.

Changes the horizontal position of the monitor's entire display.

V-Position

Changes the vertical position of the monitor's entire display.
Description You can choose one of nine languages.

Language

The language chosen affects only the language of the OSD. It has no effect on any software running on the computer.
You can change the horizontal position where the OSD menu appears on your monitor.
You can change the vertical position where the OSD menu appears on your monitor.

Transparency

Change the transparency of the background of the OSD.

Display Time

The menu will be automatically turned off if no adjustments are made for a certain time period. You can set the amount of time the menu will wait before it is turned off. - 5 sec, 10 sec, 20 sec, 200 sec
Description Select Auto Source for the monitor to automatically select the signal source.

Auto Source

Image Reset
Image parameters are replaced with the factory default values.

Color Reset

Color parameters are replaced with the factory default values.

Information

Description Shows a video source, display mode on the OSD screen.

Check List

Before calling for service, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer.
Symptom No images on the screen. I cannot turn on the monitor.
Check List Is the power cord connected properly? Can you see "Check signal cable" on the screen?
Solutions Check the power cord connection and supply.
(Connected using the D-sub cable) Check the signal cable connection. (Connected using the DVI cable) If you still see an error message on the screen when the monitor is connected properly, check to see if the monitor status is set to analog. Press ' ' button to have the monitor doublecheck the input signal source.
If the power is on, reboot the computer to see the initial screen(the login screen), which can be seen.
If the initial screen (the login screen) appears, boot the computer in the applicable mode (the safe mode for Windows ME/XP/2000) and then change the frequency of the video card. (Refer to the Preset Timing Modes) If the initial screen (the login screen) does not appear, contact the Service Center or your dealer.
Can you see "Not Optimum Mode", "Recommended Mode 1920 x Hz" on the screen?
You can see this message when the signal from the video card exceeds the maximum resolution and frequency that the monitor can handle properly. Adjust the maximum resolution and frequency that the monitor can handle properly. If the display exceeds SXGA or 75 Hz, a "Not Optimum Mode", "Recommended Mode 1920 x Hz" message is displayed. If the display exceeds 85 Hz, the display will work properly but the "Not Optimum Mode", "Recommended Mode 1920 x Hz" message appears for one minute and then disappears. Please change to the recommended mode during this one-minute period. (The message is displayed again if the system is rebooted.)

There is no image on the screen. Is the power indicator on the monitor blinking at 1 second intervals?
The monitor is in PowerSaver mode. Press a key on the keyboard to activate the monitor and restore the image on the screen. If there is still no image, press the ' ' button. Then press any key on the keyboard again to activate the monitor and restore the image on the screen.
Connected using the DVI cable?
You may get a blank screen if you boot the system before you connect the DVI cable, or disconnect and then reconnect the DVI cable while the system is running as certain types of graphic cards do not send out video signals. Connect the DVI cable and then reboot the system. Unlock the OSD by pressing the [ for at least 5 seconds. ] button
I cannot see the On Screen Display.
Have you locked the On Screen Display (OSD) Menu to prevent changes? Is the screen displaying only one color as if looking at the screen through a cellophane paper? Have the screen colors become strange after running a program or due to a crash between applications? Has the video card been set properly?
The screen shows strange colors or just black and white.
Check the signal cable connection. Make sure the video card is fully inserted in its slot.

Reboot the computer.

Set the video card by referring to the video card manual. Adjust screen image position and size using the OSD. Adjust the resolution and frequency at the video card. (Refer to the Preset Timing Modes).
The screen suddenly has become unbalanced.
Have you changed the video card or the driver? Have you adjusted the resolution or frequency to the monitor?
The screen can be unbalanced due to the cycle of the video card signals. Readjust Position by referring to the OSD. The screen is out of focus or OSD cannot be adjusted. LED is blinking but no images on the screen. Have you adjusted the resolution or frequency on the monitor? Is the frequency properly adjusted when checking the Display Timing on the menu? Adjust the resolution and frequency of the video card. (Refer to the Preset Timing Modes). Adjust the frequency properly by referring to the video card manual and the Preset Timing Modes. (The maximum frequency per resolution may differ from product to product.) Windows XP : Set the resolution at the Control Panel Appearance and Themes Display Settings. Windows ME/2000 : Set the resolution at the Control Panel Display Settings. Has the video card been set properly? There is a message that reads "Unrecognized monitor, Plug & Play Have you installed the monitor driver? Set the video card by referring to the video card manual. Install the monitor driver according to the Driver Installation Instructions.

Storage

Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will proceed automatically, unless the user wishes to select alternate settings. Dot Acceptable TFT LCD panel manufactured by using advanced semiconductor technology with precision of 1 ppm (one millionth) above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality and you can use it without uneasiness. For example, the number of TFT LCD sub pixels that is contained in this product are 6,912,000. Design and specifications are subject to change without prior notice. Class B Equipment (Information Communication equipment for residential use) This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)

PowerSaver

This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPMS compliant video card installed in your computer. Use a software utility installed on your computer to set up this feature. Power off (Power button) EPA/ENERGY 2000 Off

Normal Operation

Power saving mode

Power Indicator

Blue Blinking

Power Consumption

Less than 100 watts

Less than 2 Watts

Less than 1 watt
This monitor is EPA ENERGY STAR compliant and ENERGY2000 compliant when used with a computer equipped with VESA DPMS functionality. As an ENERGY STAR Partner, SAMSUNG has determined that this product meets the ENERGY STAR guidelines for energy efficiency.

Preset Timing Modes

If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Preset Timing Modes Horizontal Frequency (kHz) 35.000 49.726 68.681 31.469 31.469 31.469 37.500 37.861 35.156 37.879 46.875 48.077 48.363 56.476 60.023 67.500 60.000 79.976 Vertical Frequency (Hz) 66.667 74.551 75.062 70.086 59.940 70.087 75.000 72.809 56.250 60.317 75.000 72.188 60.004 70.069 75.029 75.000 60.000 75.025

Display Mode

Pixel Clock (MHz) 30.240 57.284 100.000 25.175 25.175 28.322 31.500 31.500 36.000 40.000 49.500 50.000 64.000 75.000 78.750 108.000 108.000 135.000
Sync Polarity (H/V) -/-/-/+/-/-/+ -/-/+/+ +/+ +/+ +/+ -/-/+/+ +/+ +/+ +/+
MAC, 640 x 480 MAC, 832 x 624 MAC,1152 x 870 IBM, 640 x 350 IBM, 640 x 480 IBM, 720 x 400 VESA, 640 x 480 VESA, 640 x 480 VESA, 800 x 600 VESA, 800 x 600 VESA, 800 x 600 VESA, 800 x 600 VESA, 1024 x 768 VESA, 1024 x 768 VESA, 1024 x 768 VESA, 1152 x 864 VESA, 1280 x 960 VESA, 1280 x 1024 VESA, 1920 x 1200

74.038

59.950

154.000

Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle and the inverse number of the Horizontal Cycle is called Horizontal Frequency. Unit : kHz Vertical Frequency Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called Vertical Frequency or Refresh Rate. Unit : Hz
Contact SAMSUNG WORLDWIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center.
North America U.S.A CANADA MEXICO Latin America ARGENTINE BRAZIL CHILE COLOMBIA COSTA RICA ECUADOR EL SALVADOR GUATEMALA JAMAICA PANAMA PUERTO RICO REP. DOMINICA TRINIDAD & TOBAGO VENEZUELA Europe 0800-333-3733 4004-0000 800-726-7864 (SAMSUNG) 01-8000112112 0-800-507-7267 1-800-10-7267 800-6225 1-800-299-0013 1-800-234-7267 800-7267 1-800-682-3180 1-800-751-2676 1-800-7267-864 0-800-100-5303 http://www.samsung.com/ar http://www.samsung.com/br http://www.samsung.com/cl http://www.samsung.com.co http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin 1-800-SAMSUNG (7267864) 1-800-SAMSUNG (7267864) 01-800-SAMSUNG (7267864) http://www.samsung.com http://www.samsung.com/ca http://www.samsung.com/mx

BELGIUM CZECH REPUBLIC

000 844
http://www.samsung.com/be http://www.samsung.com/cz
DENMARK FINLAND FRANCE GERMANY HUNGARY ITALIA LUXEMBURG NETHERLANDS NORWAY POLAND PORTUGAL REPUBLIC OF IRELAND SLOVAKIA SPAIN SWEDEN SWITZERLAND U.K CIS ESTONIA LATVIA LITHUANIA KAZAKHSTAN RUSSIA UKRAINE UZBEKISTAN Asia Pacific AUSTRALIA CHINA HONG KONG
030-3260 SAMSUNG(7267864) ( 0,15/min) 01805 - 121213 ( 0,14/Min) 06-80-SAMSUNG (7267864) 800 SAMSUNG (7267864) 0032 (0)( 0,10/Min) 815-100 0800-SAMSUNG (7267864) 0771-0800-SAMSUNG (7267864)
http://www.samsung.com/dk http://www.samsung.com/fi http://www.samsung.com/fr http://www.samsung.de http://www.samsung.com/hu http://www.samsung.com/it http://www.samsung.lu http://www.samsung.com/nl http://www.samsung.com/no http://www.samsung.com/pl http://www.samsung.com/pt http://www.samsung.com/uk http://www.samsung.com/sk http://www.samsung.com/es http://www.samsung.com/se http://www.samsung.com/ch http://www.samsung.com/uk
800-7267 800-7267 8-800-1188 8-800-200-0400 8-800-503-0000 140-1234
http://www.samsung.ee http://www.samsung.com/lv http://www.samsung.lt http://www.samsung.kz http://www.samsung.ru http://www.samsung.com/ur http://www.samsung.uz
603 800-810-5858, 010- 3698-4698
http://www.samsung.com/au http://www.samsung.com.cn http://www.samsung.com/hk
INDIA INDONESIA JAPAN MALAYSIA PHILIPPINES SINGAPORE THAILAND TAIWAN VIETNAM Middle East & Africa SOUTH AFRICA U.A.E
3030 8282, 11 0800-112-8888 0120-327-527 1800-88-9999 1800-10-SAMSUNG (7267864) 1800-SAMSUNG (7267864) 1800-29-3232, 03-689-3232 0800-329-889
http://www.samsung.com/in http://www.samsung.com/id http://www.samsung.com/jp http://www.samsung.com/my http://www.samsung.com/ph http://www.samsung.com/sg http://www.samsung.com/th http://www.samsung.com/tw http://www.samsung.com/vn
(SAMSUNG) 800SAMSUNG (7267864) 8000-4726
http://www.samsung.com/za http://www.samsung.com/mea
Dot Pitch The image on a monitor is composed of red, green and blue dots. The closer the dots, the higher the resolution. The distance between two dots of the same color is called the 'Dot Pitch'. Unit : mm
Vertical Frequency The screen must be redrawn several times per second in order to create and display an image for the user. The frequency of this repetition per second is called Vertical Frequency or Refresh Rate. Unit : Hz Example : If the same light repeats itself 60 times per second, this is regarded as 60 Hz.

Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle. The inverse number of the Horizontal Cycle is called Horizontal Frequency. Unit : kHz
Interlace and Non-Interlace Methods Showing the horizontal lines of the screen from the top to the bottom in order is called the NonInterlace method while showing odd lines and then even lines in turn is called the Interlace method. The Non-Interlace method is used for the majority of monitors to ensure a clear image. The Interlace method is the same as that used in TVs.
Plug & Play This is a function that provides the best quality screen for the user by allowing the computer and the monitor to exchange information automatically. This monitor follows the international standard VESA DDC for the Plug & Play function.

Resolution

The number of horizontal and vertical dots used to compose the screen image is called 'resolution'. This number shows the accuracy of the display. High resolution is good for performing multiple tasks as more image information can be shown on the screen. Example : If the resolution is 1920 x 1200 , this means the screen is composed of 1920 horizontal dots (horizontal resolution) and 1200 vertical lines (vertical resolution).

For Better Display

Adjust computer resolution and screen injection rate (refresh rate) oncomputer as described below to enjoy the best quality of picture. You can have an uneven quality of picture in the screen if the best quality of picture is not provided in TFT-LCD. Resolution : 1920 x 1200 Vertical frequency (refresh rate) : 60 Hz TFT LCD panel manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality and you can use it without uneasiness. For example, the number of TFT LCD sub pixels that is contained in this product are 6,912,000. When you clean the monitor and the panel outside, please apply the recommended small amount of cleaner by using soft and dry cloth and polish it. Let LCD area not to be forced but to be scrubbed out softly. If excessive force is applied, you can have a stain on it. If you are not satisfied with the quality of the picture, you can get better quality of the picture by executing "auto adjustment function" in display screen that is appeared as window termination button is pressed. If there's still noise after automatic adjustment, use FINE/COARSE adjustment function. If you view a fixed screen for an extended period of time, residual image or blurriness may appear. Change the mode to energy save or set a screensaver to move the picture when you need to be away from the monitor for an extended period of time.

Authority

Information in this document is subject to change without notice. 2007 Samsung Electronics Co., Ltd. All rights reserved. Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly forbidden. Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. Samsung is the registered trademark of Samsung Electronics Co., Ltd.; Microsoft, Windows and Windows NT are registered trademarks of Microsoft Corporation; VESA, DPMS and DDC are registered trademarks of Video Electronics Standard Association; the ENERGY STAR name and logo are registered trademarks of the U.S. Environmental Protection Agency (EPA). As an ENERGY STAR Partner, Samsung Electronics Co., Ltd. has determined that this product meets the ENERGY STAR guidelines for energy efficiency. All other product names mentioned herein may be the trademarks or registered trademarks of their respective owners.

IMPORTADO POR:

SAMSUNG ELECTRONICS MXICO. S.A. de C.V. Va Lopez Portillo No. 6, Col. San Fco. Chilpan Tultitln, Estado de Mxico, C.P. 54940 Tel: 01-55-5747-5100 / 01-800-726-7864 Samsung Electronics CO.,LTD. 416, Mae tan-3dong, Yeongtong - gu, Suwon City, Gyeonggi-do Korea

EXPORTADO POR:

Product sheet Art #:193 SAMSUNG SYNCMASTER 245B 24LCD COMPUTERMONITOE 1980*1200 16:10 DVI/VGA
Technical Information Panel Viewable area 24 16:10 Wide Format Display Pixel Pitch 0.270 x 0.270mm Brightness(typ.) 400cd/m2 Contrast Ratio(typ.) 1000:1(DC 3000:1) Viewing Angle(H/V) 160/160 Response Time(typ.) 5 Frequency Horizontal Frequency 30~81kHz Vertical Frequency 56~75Hz Maximum Resolution 1920 x 1200@60Hz (Analog), 1920 x 1200@60Hz Color Supported 16.7Mil. Signal Input Input Video Signal Analog RGB, DVI Sync. Type Separate H/V, Composite H/V, SOG Input Connectors 15pin D-sub, DVI-D Plug & Play DDC 2B Mac Compatibility O Power On Mode 100 Watts DPMS Mode <2W Type Built-in Wall-Mount VESA 200 x 100 TCO TCO 03 (Non glossy) Cabinet Color Black high glossy/Black/Silver Dimension Set(WxHxD)(with Stand) 560.0x444.5x250.0m Set(WxHxD)(w/o Stand) 560.0x368.5x83.0mm Packing(WxHxD) 733 x 557 x 350mm Weight Set 8.4kg Special Features PC : Analog, Digital MagicColor, MagicBright3 Stand Type Best Ergonomic HAS (100mm) Function Height Adjustable & Swivel & Tilt

Product Information

With a 24 large 16:10 wide screen. Windows Vista Premium Ready High Resolution (1920 x 1200) Clearer and sharper images Dynamic Contrast 3000:1 Fast Response Time 5ms guarantees seamless viewing of motion pictures. No ghosting, no blurring. Magic Bright III 7 preset viewing modes are available: text, internet, game, sport, movie, dynamic and custom. Pixel Pitch HDCP (High-Bandwidth Digital Content Protection) Enjoy perfect picture quality when linking to the DVI interface. More security, more quality, more entertainment. Innovative Power Saving System Less than 2w when the monitor is in stand-by mode. Wall Mountable
Centas Konferens-TV AB Orgnr:556206-7289 Ste Stockholm www.centas.se
Fryksdalsbacken 43 Farsta Tel:Fax:08 7240410
Norra Gubberogatan 63 Gteborg 031 841144
Regnvattengatan 23 Malm 040 143810