The customer can return used or rechargeable batteries to a nearby public
recycling center or to a store selling the same type of the battery or rechargeable battery.
1995~2007 SAMSUNG. ALL Rights Reserved
Safety Instructions Introduction
Package Contents Your LCD Display Machanical Layout
Connections Using the Software Adjusting the LCD Display Troubleshooting Specifications Information Appendix
The color and appearance of the product may vary depending on the model, and the product specifications are subject to change without prior notice for reasons of performance enhancement.

Introduction

Package Contents
Note Please make sure the following items are included with your LCD Display. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Note This stand is not for the Floor Standing Type.

LCD Display

Manuals

Quick Setup Guide

Warranty Card (Not available in all locations)
User's Guide, MDC Software

Cables

D-Sub Cable

Power Cord

Speaker Wire Cable

Remote Control

Batteries (AAA X 2)

Cover-Hole

BNC to RCA Adaptor Jack

Semi Stand

Sold separately

Wall Mount KIT

Speaker Set

Stand KIT

DVI Cable

BNC Cable

Your LCD Display Front
Opens the on-screen menu and exits from the menu or closes the adjustment menu.
Navigate buttons (Up-Down buttons)
Moves from one menu item to another vertically or adjusts selected menu values.
Adjust buttons (Left-Right buttons)/ Volume buttons
Moves from one menu item to another horizontally or adjusts selected menu values.
Adjusts the audio volume.
Activates a highlighted menu item.

SOURCE

Switches from PC mode to Video mode. Changing the source is only allowed for external devices that are connected to the LCD Display at the time. [PC] [BNC] [DVI] [AV] [S-Video] [Component] >> Click here to see an animation clip.
Push the PIP button to turn the PIP screen On / Off. More than one PIP cannot overlap on screen as BNC and the component use the same terminal. >> Click here to see an animation clip. PC AV / S-Video / Component Mode BNC AV / S-Video Mode DVI AV / S-Video / Component Mode AV / S-Video PC / BNC / DVI Mode Component PC / DVI Mode

Power button

Turns the LCD Display On/Off.

Power indicator

Shows PowerSaver mode by blinking green.

Remote Control Sensor

Aim the remote control towards this spot on the LCD Display.

Contact a technician for installing the wall bracket. Samsung Electronics is not responsible for any damages to the product or harm to customers when the installation is done by the customer. This product is for installing on cement walls. The product may not stay in place when installed on plaster or wood. Components(Sold separately) Only use the components and accessories shipped with the product.
A Wall-Bracket B Set-Bracket C
Screw: Screw: Wood Screw: Anchor: D E F G Installation Guide 8 EA 3 EA 7 EA 7 EA
How to assemble the Wall Mount Bracket

1. 2. 3. 4.

Mark the location of hole on the wall. Make over 35mm-depth-hole on the marked location using drill. Fix anchors F on each hole on the wall. Connect wall-bracket A to the wall with wood screws E after fitting anchors F into the wall-bracket A. If the bracket is not firmly fixed to the wall, set can fall off.
1. Turn the power off and unplug the power cord from the outlet. 2. Place the monitor faced down on a soft cloth or cushion on a table. 3. Attach the set-bracket B onto the rear side of the monitor set and secure the screws C.
1. Insert three Hangers of the set-bracket B into the grooves of the wall-bracket A. 2. Fix set-bracket B and wall-bracket A with screws D. Before installing the set on the wall, connect the cables to the set first.
Safety Instructions Introduction Connections
Installing the Stand KIT Connecting the LCD Display
Using the Software Adjusting the LCD Display Troubleshooting Specifications Information Appendix

Connections

Installing the Stand KIT
Note Only the supplied bolts should be used.

Caution

Samsung Electronics will not be responsible for damages caused by using a base other than those specified.
Installing the Semi Stand

Left stand

Right stand
Make sure to install the stand with the Caution label folded backwards.
A 'Cover-Protector' is used to protect the hole at the bottom of the LCD Display , where the stand is inserted. Be sure to remove the 'Cover-Protector' when attaching the provided Semi Stand or Stand KIT (sold separately) and cover the hole using the 'Cover-Hole' when attaching the wall mount kit.
Set up the left and right stands respectively. Insert the stand into the hole at the bottom of the LCD Display. Insert the screw into the hole indicated and tighten it. (M4 x L15)
This stand is designed for adjusting the screen angle. The company is not responsible for any problem caused when using this stand. Under no circumstances use the product as a stand for placing something on.

Installing the Stand KIT (sold separately)

2) 3) 4)

Ensure that the parts are inserted in the right direction and in the right place. (M4 x L15) Insert the stand into the hole at the bottom of the LCD Display. Insert the screw into the hole indicated and tighten it. (M4 x L15)
Connecting the LCD Display
Using a Power cord with Earth
In the event of failure, the earth lead may cause electric shock. Make sure to wire the earth lead in correctly, before connecting the AC power. When un-wiring the earth lead, make sure to disconnect the AC power in advance.
Note AV input devices such as DVD players, VCR's or camcorders as well as your computer can be connected to the LCD Display. For detailed information on connecting AV input devices, refer to the User Controls under Adjusting Your LCD Display.

Connecting to a Computer

Connect the power cord for your LCD Display to the power port on the back of the LCD Display. Trun on the power switch.
There are 3 ways to connect the D-sub to your LCD Display. Choose one of the following: 2-1) Using the D -sub (Analog) connector on the video card. Connect the D -sub to the 15-pin, RGB port on the back of your LCD Display and the 15 pin D sub Port on the computer.
Using the DVI (Digital) connector on the video card. Connect the DVI Cable to the DVI(HDCP) port on the back of your LCD Display and the DVI port on the computer.
Using the BNC (Analog) connector on the video card. Connect the BNC Cable to the BNC/COMPONENT IN - R, G, B, H, V ports on the back of your LCD Display and the 15 pin D-sub Port on the computer.
Connect the audio cable for your LCD Display to the audio port on the back of your computer.
Note Turn on both your computer and the LCD Display.
Note The DVI cable or BNC cable is optional. Contact a local Samsung Electronics Service Center to buy optional items.

Connecting Digital DVD

Note Input devices such as digital DVD are connected to the DVI IN terminal of the monitor using the DVI cable. Then, start the DVD with a DVD disc inserted. Select Digital using the SOURCE button. Note The monitor has DVI IN connection terminals to connect DVI input devices digital DVD.

Connecting to a VCR

AV input devices such as VCRs or Camcorders are connected via the AV IN [VIDEO] or AV IN [S -VIDEO] of the LCD Display using an S-VHS or BNC cable.
Connect the Audio (L) and Audio (R) terminals of a VCR or Camcorders to the LCD Display 's AV AUDIO IN [L-AUDIO -R] using audio cables.
Note Select AV or S-Video for a connected VCR or Camcorder using the SOURCE button on the front of the LCD Display or on the remote control. Then, start the VCR or Camcorders with a tape inserted.

Main Screen

Click Start > Program > Samsung > MDC System to start the program. Select a set to see the volume of the selected set within the slider.
Main Icons Remocon Safety Lock Port Selection 1. Use the main icons to switch into each screen.
Select Button Info Grid Display Selection Control Tools
2. Allows you to enable or disable the remote control signal receiving function of the display unit. 3. Set the Safety Lock function. When setting the Lock function, you can only operate power and lock buttons on the remote control and set. 4. The setting for the PC Serial Port can change. The original value is COM1. 5. Click Select all or Clear to select or clear all displays. 6. Use Grid to view brief information on selected display. 7. Select a display from Display Selection. 8. Use Control Tools to control displays. <Note> The remote control Enable/Disable function operates whether or not the power is On/Off, and this applies to all displays connected to the MDC. However, regardless of the status at the time the MDC is shut down, the remote control signal receiving function of all displays is initialized to Enable when the MDC is closed.

Port Selection

1. The Multiple Display Control is originally set to COM1. 2. If any port other than COM1 is used, COM1 through COM4 can be selected in the Port Selection Menu. 3. If the exact port name that is connected to the LCD Display using a serial cable is not selected, communication will be unavailable. 4. The selected port is stored in the program and used for the next program as well.

Power Control

1. Click Power Control of the main icons and the Power Control screen appears.
Info Grid shows some basic information necessary to Power Control. 1) (Power Status) 2) Input 3) Image Size 4) On Timer 5) Off Timer 2. Use the Select All button or Check Box to choose a display to control.
Power Control allows controlling some of the functions of the selected display. 1) Power On/Off
- Turns the power of the selected display On/Off. 2) Volume - Controls the volume level of the selected display. It receives the volume value of the selected display from the sets and displays it in the slider. (When you cancel the selection or choose Select All, the value returns to the default value 10) 3) (Mute On/Off) - Turns on/off the Mute function of the selected display. When selecting one set at a time, turn on the Mute function for the selected set. The Mute function is disabled automatically when you adjust the volume level. (The values return to the default settings when you undo the selections or choose "Select All".) The Power Control feature is available for all displays. The Volume Control and Mute features are available only for the displays whose power status is ON.

Input Source

1. Click Input Source of the main icons and the Input Source control screen appears. Click Select All or use Check Box to select a display to control. TV Mode

1. Click Time of the main icons and the Time Control screen appears.
Info Grid shows some basic information necessary to Time Control. 1) Current Time - Set the current time for the selected display (PC Time). - To change the current time, first change the PC Time. 2) On Time Setup - Set the Hour, Minute, AM/PM of On Time Setup, Status, Source, Volume of the selected display. 3) Off Time Setup - Set the Hour, Minute, and AM/PM, Status for Off Time Setup of the selected display. 4) Shows the On Time settings. 5) Shows the Off Time settings. The Input source of MagicNet works only on MagicNet model. The Input source of TV works only on TV model. Time Control is available only for the displays for which the power status is ON. At On Time Setup, TV Source functions only for TV Model. At On Time Setup, MagicNet Source functions only for MagicNet Model.

PIP PIP Size

1. Click PIP of the main icons and the PIP control screen appears. Click Select All or use Check Box to select a display to control.
Info Grid shows some basic information necessary to PIP Size Control. 1) PIP Size - Shows the current PIP Size of the display in use. 2) OFF - Turns off the PIP of the selected display. 3) Large - Turns on the PIP of the selected display and changes the size to Large. 4) Small - Turns on the PIP of the selected display and changes the size to Small. 5) Double 1 - Turns on the PIP of the selected display and changes the size to Double 1. 6) Double 2 - Turns on the PIP of the selected display and changes the size to Double 2. 7) Double 3 (Picture By Picture) - Turns on the PBP of the selected display and changes the size to Double 3. The Input source of MagicNet works only on MagicNet model. The Input source of TV works only on TV model. PIP Size can be controlled with turning on the LCD Display power.

PIP PIP Source

1. Click PIP of the main icons and the PIP control screen appears. PIP TV Mode

PIP S-Video Mode

Info Grid shows some basic information necessary to PIP Source Control. 1) PIP Source - PIP Source can be controlled with turning on the LCD Display power. 2) PC - Changes the source of the PIP of the selected display to PC. 3) BNC - Changes the source of the PIP of the selected display to BNC. 4) DVI - Changes the source of the PIP of the selected display to DVI. 5) TV -Changes the source of the PIP of the selected display to TV.
6) AV - Changes the source of the PIP of the selected display to AV. 7) S-Video - Changes the source of the PIP of the selected display to S-Video. 8) Component - Changes the source of the PIP of the selected display to Component. 9) Channel - Channel arrow appears when the PIP Source is TV. Note: Some of the PIP Sources may not be available for selection, depending on the input source type of the Main Screen. The Input source of MagicNet works only on MagicNet model. The Input source of TV works only on TV model. TV Source can be selected only in products with TV and controlling channels is allowed only when PIP Source is TV. The PIP Control feature is available only for the displays whose power status is ON and the PIP function is set to ON.

Maintenance Scroll

1) Safety Screen - Eliminates the afterimages that can result when the selected display stays in Pause mode for an extended period of time. You can set the repeat cycle timer by selecting the "Interval" by hour and "Second" by second. It can be set to Scroll, Pixel, Bar and Eraser by Screen Type. The Input source of MagicNet works only on MagicNet model. The Input source of TV works only on TV model. Setting Second, you can set to 1, 2, 3, 4, 5 for Scroll Type and to 10, 20, 30, 40, 50 for Pixel, Bar, and Eraser Type. The Maintenance Control feature is available only for the displays whose power status is ON.

Maintenance Video Wall

1) Video Wall - A Video Wall is a set of video screens that are connected together, so that each screen shows a part of the whole picture or so that the same picture is repeated on each screen. 2) Video Wall (Screen divider) - The screen can be divided into. You can select a number of screens with a different layout when dividing. Select a mode from Screen divider. Select a display from Display Selection. The place will be set up by pressing a number in the selected mode. The MDC program supplied by Samsung supports over 4*4. 2*2

3) On / Off

- Turns on/off the Video Wall function of the selected display. 4) Format - The format can be selected to see a divided screen.

Natural

You may not operate this function in MagicNet. The Input source of TV works only on TV model. The Maintenance Control function is available only for the displays where the power status is ON.

Troubleshooting

1. The display you wish to control does not appear on the Power Control Info Grid - Check the connection of RS232C. (Check if it is properly connected to the Com1 port) - Check the displays to see if any of the other displays connected have the same ID. If more than one displays have the same ID, those displays are not properly detected by the program due to data conflict. - Check if the Display Set ID is a number between 0 and 16. (Adjust using the Display menu) Note : A Display Set ID must be a value between 0 and 16.
2. The display you wish to control does not appear on the other Control Info Grids - Check to see if the display power is ON. (You can check this in Power Control Info Grid) - Check if you can change the input source of the display. 3. The dialogue box appears repeatedly. - Check to see if the display you wish to control is selected. 4. Both On Timer and Off Timer have been set but different time is showing. - Apply current time to synchronize the display clocks. 5. The remote may not function properly when you turn off the remote Function, disconnect the RS-232C cable, or exit the program in an Irregular manner. Rerun the program and turn the remote function again to Restore normal functions. <Note> This program may malfunction due to problems in communication circuits or interference from electronic appliances nearby.

6) Transparency

[ME NU] [ENTER] [ / ] [ENTER] [ / ] [ENTER] [ / ] [ENTER] Adjusts the Transparency of PIP windows.
- High - Medium - Low - Opaque
Note If you select , , in Size, Position and Transparency will not be activated.

Available Modes: PIP ON

Edit Name
[ME NU] [ENTER] [ / ] [ENTER] [ / ] [ENTER] [ / ] [ENTER] Name the input device connected to the input jacks to make your input source selection easier.
1) PC 2) BNC 3) DVI 4) AV

5) S-Video 6) Component

Picture [PC / BNC /DVI Mode]

MagicBright

[ME NU] [ / ] [ENTER] [ENTER] [ / ] [ENTER] MagicBright is a new feature providing the optimum viewing environment depending on the contents of the image you are watching. Currently four different modes are available: Entertain, Internet, Text and Custom. Each mode has its own pre-configured brightness value. You can easily select one of the four settings by simply pressing the MagicBright control button.

1) Entertain

High brightness For watching motion pictures such as a DVD or VCD.

2) Internet

Medium brightness For working with a mixture of images such as the text with graphics added.

3) Text

Normal brightness For documentations or work involving a lot of text.

4) Custom

Although the values are carefully chosen by our engineers, the pre-configured values may not be comfortable for your eyes depending on your taste. If this is the case, Adjusts the brightness and contrast by using the OSD menu.
[The direct button on the remote control is the 'M/B' button.]

Custom

[ME NU] [ / ] [ENTER] [ / ] [ENTER] [ENTER] [ / ] / [< / >] [ENTER] By using the on-screen menus, the contrast and brightness can be changed to your personal preference.

1) Contrast

Adjusts the Contrast.

2) Brightness

Adjusts the Brightness. Note By adjusting the picture using the Custom function, MagicBright will change to Custom mode.

Color Tone

[ME NU] [ / ] [ENTER] [ / ] [ENTER] [ / ] [ENTER] The color tones can be changed.
1) Cool 2) Normal 3) Warm 4) Custom (Available in PC, BNC mode only)

Color Control

[ME NU] [ / ] [ENTER] [ / ] [ENTER] [ENTER] [< / >] [ENTER] Adjusts the individual R, G, B color controls. (Available in PC, BNC mode only)

1) Red 2) Green 3) Blue

Note If you adjust the picture by using the Custom function, Color Tone will turn to the Cusome mode.

[ME NU] [ / ] [ENTER] [ / ] [ENTER] [ / ] [ENTER] [ / ] [ENTER] You can change the Safety Screen Type. - Scroll - Pixel - Bar - Eraser

Resolution Select

[ME NU] [ / ] [ENTER] [ / ] [ENTER] [ / ] [ENTER] When the picture is not displayed properly on the screen when setting the graphics card resolution of the computer to 1024 x 768 @ 60Hz, 1280 x 768 @ 60Hz, 1360 x 768 @ 60Hz or 1366 x768 @ 60Hz, by using this function(Resolution Select), you can have the picture displayed on the screen in the specified resolution. Available in PC/BNC mode only
1) Off 2) 1024 X 768 3) 1280 X 768 4) 1360 X 768 5) 1366 X 768
Note Selecting the menu is only allowed when the graphics resolution is set to 1024 x 768 @ 60Hz, 1280 x 768 @ 60Hz, 1360 x 768 @ 60Hz or 1366 x768 @ 60Hz.

Lamp Control

[ME NU] [ / ] [ENTER] [ / ] [ENTER] [ENTER] [< / >] [ENTER] Adjusts the inverter lamp in order to reduce energy consumption.

Power On Adjustment

[ME NU] [ / ] [ENTER] [ / ] [ENTER] [ENTER] [ / ] [ENTER] Adjusts the Power On time for the screen. *Caution: Set the Power On time to be loger to avoid overvoltage.

1) Image Reset

[ME NU] [ / ] [ENTER] [ / ] [ENTER] [ENTER] [< / >] [ENTER] Available in PC/BNC mode only

2) Color Reset

[ME NU] [ / ] [ENTER] [ / ] [ENTER] [ / ] [ENTER] [< / >] [ENTER]

Multi Control

Assigns an individual ID to the SET.

1) ID Setup

[ME NU] [ / ] [ENTER] [ / ] [ENTER] [ENTER] [0~9] Assigns distinctive IDs to the SET.

2) ID Input

[ME NU] [ / ] [ENTER] [ / ] [ENTER] [ENTER] [0~9] Use to select the transmitter functions of the individual SET. Only a SET where the ID corresponds to the transmitter setting becomes activated.

Direct Functions

Moves to the Multi Control OSD screen.
Sets the Safety Lock function.

1) Lock On

It will be locked.

2) Lock Off

It wil be unlocked. Note When setting the Lock function, you can only operate the power and lock buttons on the remote control and set. The preset password on the LCD Display is "0000". Note Resetting the password for the function key lock. Press INFO EXIT MUTE. The password will be reset to '0000'. The remote control is required for resetting the password.

Safety Instructions Introduction Connections Using the Software Adjusting the LCD Display Troubleshooting
Self-Test Feature Check Check List Q& A
Specifications Information Appendix

Self-Test Feature Check

Note Check the following items yourself before calling for assistance. Contact a Service Center for problems that you cannot solve by yourself.
Your LCD Display provides a self test feature that allows you to check whether your LCD Display is functioning properly. 1) 2) 3) Turn off both your computer and the LCD Display. Unplug the video cable from the back of the computer. Turn on the LCD Display. The figure shown below ("Check Signal Cable") appears on a black background when the LCD Display is working normally even though no video signal is detected: While in the Self-Test mode, the LED power indicator remains green and the figure moves around on the screen.
Turn off your LCD Display and reconnect the video cable; then turn on both your computer and the LCD Display
If your LCD Display screen remains blank after using the previous procedure, check your video controller and computer system; your LCD Display is functioning properly.

Not Optimum Mode

You can even view the screen at a resolution of 1360 X 768. However, you will receive the following message for a minute; You can choose to change the screen resolution or stay in the current mode during that time. And if the resolution is more than 85Hz, you will see the black screen because the LCD Display does not support over 85Hz.
Note Refer to Specifications > Preset Timing Modes for the resolutions or frequencies supported by the LCD Display.

Maintenance and Cleaning

Maintaining the LCD Display Case. Clean with a soft cloth after disconnecting the power cord.
Do not use benzene, thinner or other flammable substances, or a wet cloth.
We recommend that a Samsung cleansing agent is used to prevent damage to the screen.
Maintaining the Flat Panel Display Screen. Clean with a soft cloth (cotton flannel) smoothly. Never use acetone, benzene or thinner. (They may cause flaws or deformation of the screen surface.) The user will be required to pay costs and related expenses for repairing damages caused.
Symptoms and Recommended Actions
Note A LCD Display recreates visual signals received from the computer. Therefore, if there is a problem with the computer or the video card, this can cause the LCD Display to become blank, have poor coloring, become noisy, and video mode not supported, etc. In this case, first check the source of the problem, and then contact a Service Center or your dealer.
Check if the power cord and the video cables are properly connected to the computer. Check if the computer beeps more than 3 times when booting. (If it does, request an a service for the main board of the computer.)

If you installed a new video card or if you assembled the PC, check if you installed the Adaptor(video). Check if the scanning ratio of the video screen is set to between 50 Hz ~ 85 Hz. (Do not exceed 60Hz when using the maximum resolution.)
If you have problems in installing the Adaptor (video) driver, boot the computer in Safe Mode, remove the Display Adaptor in the "Control Panel, System, Device Administrator" and then reboot the computer to reinstall the Adaptor (video) driver.

Check List

Note The following table lists possible problems and their solutions. Before calling for assistance, check the information in this section to see if you can remedy any problems for yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer.
Problems related to the Installation (PC Mode)
Note Problems related to the LCD Display installation and their solutions are listed.
Problems The LCD Display screen flickers.

Solutions

Check if the signal cable between the computer and the LCD Display is securely connected.
(Refer to Connecting to a Computer)
Problems related to the Screen
Note Problems related to the LCD Display screen and their solutions are listed.
Problems The screen is blank and the power indicator is off.
Ensure that the power cord is firmly connected and the LCD LCD Display is on. (Refer to the Connecting the LCD Display )
"Check Signal Cable" message.
Ensure that the signal cable is firmly connected to the PC or video sources. (Refer to the Connecting the LCD Display ) Ensure that the PC or video sources are turned on.
"Not Optimum Mode " message.
Check the maximum resolution and the frequency of the video Adaptor. Compare these values with the data in the Preset Timing Modes Chart.
The picture rolls vertically.
Check if the signal cable is securely connected. Re -connect it, if necessary. (Refer to Connecting to a Computer)
The image is not clear; picture is blurred.
Run Frequency Coarse and Fine tuning. Turn on again after removing all accessories (video extension cable, etc.) Set the resolution and frequency to the recommended ranges.

Signal Connectors

D-sub, BNC, DVI-D, YPbPr, S -VHS, VCR
Dimensions (WxHxD)/ Weight
780 X 482 X 107 mm / 30.1 X 19.0 X 4.6 inch (without Stand), 16.1 kg / 35.4 lbs 780 X 530 X 223 mm / 30.1 X 20.9 X 8.8 inch (with Stand)

VESA Mounting Interface

200 mm x 200 mm (for use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Operating Storage Temperature: 50 F ~ 104 F (10 C ~ 40 C) Humidity: 10 % ~ 80 %, non-condensing Temperature: -4 F ~ 113 F (-20 C ~ 45 C) Humidity: 5 % ~ 95 %, non-condensing

Audio Characteristics

Audio Input 1 RCA Jack Red(R) White(L), 0.5 Vrms (-9 dB)
Audio Input 2 PC Audio Input Frequency Response
RCA Jack Red(R) White(L), 0.5 Vrms (-9 dB) 3.5 Stereo Jack, 0.5 Vrms (-9 dB) RF: 80 Hz ~ 15 kHz (at -3 dB) A/V: 80 Hz ~ 20 kHz (at -3 dB)

Plug and Play Capability

This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings.

Dot Acceptable

TFT LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problelms. For example, the number of TFT LCD sub pixels contained in this product are 3,133,440. Note Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use) This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)

PowerSaver

This monitor has a built -in power management system called PowerSaver. This system saves energy by switching your monitor to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPMS compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature.

The best way to protect your monitor from Image retention is to turn Power off, or set your PC, or System to operate a Screen Saver program when you are not using it. Also Warranty service will be limited based on instruction guide.
Apply the Screen Scroll function on Product Apply the Screen Scroll function - Symptom: Horizontal Bar with Black Color move up and down.
- Select method. Instruction Guide : OSD Menu -> Set Up -> Safety Screen -> Screen Scroll. Time Interval : 1 ~ 10 hours ( Recommend : 1 ). Time Period : 1 ~ 5 second ( Recommend : 5 )
Note ( Please check CD's User Guide at "OSD Function", some model's will not available )
Apply the Screen Pixel function on Product
Apply the Screen Pixel function - Symptom: Dot with Black Color move up and down.
- Select method. Instruction Guide : OSD Menu -> Set Up -> Safety Screen -> Pixel. Time Interval : 1 ~ 10 hours ( Recommend : 1 ). Time Period : 10 ~ 50 second ( Recommend : 50 ) Apply the Screen Bar function - Symptom: Horizontal / Vertical Bar with Black Color move up and down.
- Select method. Instruction Guide : OSD Menu -> Set Up -> Safety Screen -> Bar. Time Interval : 1 ~ 10 hours ( Recommend : 1 ). Time Period : 10 ~ 50 second ( Recommend : 50 )
Note ( Please check CD's User Guide at "OSD Function", some model's will not available. )
Apply the Screen Erasing function on Product Apply the Screen Erasing function - Symptom: 2 Vertical blocks move with erasing the display
- Select method. Instruction Guide : OSD Menu -> Set Up -> Safety Screen -> Eraser. Time Interval : 1 ~ 10 hours ( Recommend : 1 ). Time Period : 10 ~ 50 second ( Recommend : 50 )
Model Safety Instructions Introduction Connections Using the Software Adjusting the LCD Display Troubleshooting Specifications Information Appendix
Contact SAMSUNG WORLDWIDE
Contact SAMSUNG WORLDWIDE Terms Correct Disposal Authority
Note If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center.
North America U.S.A CANADA MEXICO
1-800-SAMSUNG (7267864) 1-800-SAMSUNG (7267864) 01-800-SAMSUNG (7267864) http://www.samsung.com http://www.samsung.com/ca http://www.samsung.com/mx
Latin America ARGENTINE BRAZIL CHILE COLOMBIA COSTA RICA ECUADOR EL SALVADOR GUATEMALA JAMAICA PANAMA PUERTO RICO REP. DOMINICA TRINIDAD & TOBAGO VENEZUELA
0800-333-3733 4004-0000 800-726-7864 (SAMSUNG) 01-8000112112 0-800-507-7267 1-800-10-7267 800-6225 1-800-299-0013 1-800-234-7267 800-7267 1-800-682-3180 1-800-751-2676 1-800-7267-864 1-800-100-5303 http://www.samsung.com/ar http://www.samsung.com/br http://www.samsung.com/cl http://www.samsung.com.co http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin

Europe BELGIUM

http://www.samsung.com/be http://www.samsung.com/cz

CZECH REPUBLIC

DENMARK FINLAND FRANCE GERMANY HUNGARY ITALIA LUXEMBURG NETHERLANDS NORWAY POLAND PORTUGAL REPUBLIC OF IRELAND SLOVAKIA SPAIN SWEDEN SWITZERLAND U.K
( 0,15/min) 01805-121213 ( 0,14/Min) 06-80-SAMSUNG (7267864) 800 SAMSUNG (7267864) ( 0,10/Min) 0800-SAMSUNG (7267864) 1-800-SAMSUNG (7267864) 0870 SAMSUNG (7267864)
http://www.samsung.com/dk http://www.samsung.com/fi http://www.samsung.com/fr http://www.samsung.de http://www.samsung.com/hu http://www.samsung.com/it http://www.samsung.lu http://www.samsung.com/nl http://www.samsung.com/no http://www.samsung.com/pl http://www.samsung.com/pt http://www.samsung.com/uk http://www.samsung.com/sk http://www.samsung.com/es http://www.samsung.com/se http://www.samsung.com/ch http://www.samsung.com/uk
CIS ESTONIA LATVIA LITHUANIA KAZAKHSTAN RUSSIA UKRAINE UZBEKISTAN
800-7267 800-7267 800-1188 8-800-200-0400 8-800-502-0000 140-1234 http://www.samsung.ee http://www.samsung.com/lv http://www.samsung.lt http://www.samsung.kz http://www.samsung.ru http://www.samsung.com/ur http://www.samsung.uz
Asia Pacific AUSTRALIA CHINA HONG KONG INDIA INDONESIA JAPAN MALAYSIA PHILIPPINES SINGAPORE THAILAND TAIWAN VIETNAM
603 800-810-5858, 010- 3698-8282, 11 0800-112-8888 0120-327-527 1800-88-9999 1800-10-SAMSUNG (7267864) 1800-SAMSUNG (7267864) 1800-29-3232, 02-689-3232 0800-329-889 http://www.samsung.com/au http://www.samsung.com.cn http://www.samsung.com/hk http://www.samsung.com/in http://www.samsung.com/id http://www.samsung.com/jp http://www.samsung.com/my http://www.samsung.com/ph http://www.samsung.com/sg http://www.samsung.com/th http://www.samsung.com/tw http://www.samsung.com/vn
Middle East & Africa SOUTH AFRICA U.A.E
(SAMSUNG) 800SAMSUNG (7267864) 8000-4726 http://www.samsung.com/za http://www.samsung.com/mea

Sync Signal

Sync (Synchronized) Signals refer to the standard signals that are required to display desired colors on the LCD Display. They are divided into Vertical and Horizontal Sync Signals. These signals display normal color images by the set resolution and frequency. Types of Sync Signals Separate Composite This is a scheme of transmitting individual vertical sync signals to the LCD Display. This is a scheme of combining vertical sync signals into one composite signal and transmitting it to the LCD Display. The LCD Display displays the color signals by separating the composite signal into original color signals.

SyncMaster T200HD/T220HD

LCD Monitor

User Manual

Safety Instructions

Notational

Note These safety instructions must be followed to ensure your safety and prevent property damage. Make sure to read the instructions carefully and use the product in the correct manner. Warning / Caution Otherwise, it may result in death or personal injury. Otherwise, it may result in personal injury or property damage.

Notational Conventions

Prohibited
Important to read and understand at all times Disconnect the plug from the outlet Ground to prevent an electric shock

Do not disassemble

Do not touch
When not used for extended period of time, set your computer to DPM. If using screen saver, set it to active screen mode. The images here are for reference only, and are not applicable in all cases (or countries). Shortcut to Anti-Afterimage Instructions Do not use a damaged power cord or plug or a damaged or loose power outlet. Otherwise, this may result in electric shock or fire.
Do not touch the power plug with wet hands when removing or plugging the plug into the outlet. Otherwise, this may result in electric shock. Make sure to connect the power cord to a grounded power outlet. Otherwise, it may result in electric shock or personal injury.
Ensure that the power plug is plugged into the power outlet firmly and correctly. Otherwise, this may result in fire.
Do not forcefully bend or pull the power plug and do not place any heavy material on it. Otherwise, this may result in fire. Do not connect multiple appliances to the same power outlet. Otherwise, this may cause fire due to overheating.
Do not disconnect the power cord while using the product. Otherwise, this may result in damage to the product due to electric shock.
To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the mains plug shall be readily operable. This may cause electric shock or fire.
Use only the power cord provided by our company. Do not use the provided power cord of another product. Otherwise, this may result in fire or electric shock.

Installation

Be sure to contact an authorized Service Center when installing your monitor in a location with heavy dust, high or low temperatures, high humidity, and exposed to chemical substances and where it operates for 24 hours such as at airports, train stations etc. Failure to do so may cause serious damage to your monitor. Do not drop the monitor when moving it. This may cause damage to the product or the person carrying it.
Ensure that at least two persons lift and move the product. Otherwise, it may be dropped and cause personal injury, and/or damage the product.
When installing the product in a cabinet or rack, make sure that the front end of the bottom of the product does not project out. Otherwise, it may fall or cause personal injury. Use a cabinet or rack of a size appropriate to the product.
DO NOT PLACE CANDLES, MOSQUITO REPELLANT, CIGARETTES AND ANY HEATING APPLIANCES NEAR THE PRODUCT. Otherwise, this may result in fire.
Keep heating appliances as far away from the power cord or the product as possible. Otherwise, this may result in electric shock or fire.
Do not install it in a badly ventilated location such as a bookcase or closet. Otherwise, this may result in fire due to an increase in the internal temperature. Put down the monitor carefully. Failing to do so may damage the monitor.
Do not place the front of the product on the floor. Otherwise, this may result in damage to the screen display.
Ensure that an authorized installation company installs the wall mount. Otherwise, it may fall and cause personal injury. Make sure to install the specified wall mount.

Install your product in a well ventilated location. Ensure that there is a clearance of more than 10 cm from the wall. Otherwise, it may result in fire due to an increase in the internal temperature.
Bend the outdoor antenna cable downwards at the location where it goes in so that rainwater does not flow in. If rainwater enters the product, it may result in electric shock or fire. Install the antenna far away from any high voltage cables. If the antenna touches or falls onto a high voltage cable, it may result in electric shock or fire. Ensure that the packaging vinyl is kept away from children. Otherwise, it may result in serious harm (suffocation) if children play with it.
If the height of your monitor is adjustable, do not place any object or part of your body on the stand when lowering it. This may cause damage to the product or the person carrying it.
When cleaning the monitor case or the surface of the TFT-LCD screen, wipe with a slightly moistened, soft fabric.
Do not spray cleaner directly onto the surface of the product. Otherwise, this may result in the discoloration and distortion of the structure and the screen surface may peel off.
Clean the product using a soft cloth with a monitor cleaner only. If you must use a cleaner other than the monitor cleaner, dilute it with water at a ratio of 1:10.
When cleaning the power plug pins or dusting the power outlet, clean it with a dry cloth. Otherwise, it may result in fire. When cleaning the product, make sure to disconnect the power cord. Otherwise, it may result in electric shock or fire.
When cleaning the product, disconnect the power cord and clean it softly with a dry cloth. (Do not use chemicals such as wax, benzene, alcohol, thinner, mosquito repellant, lubricant, or cleaner.) These may change the appearance of the product surface and peel off the indication labels on the product.
Since the product housing is easily scratched, make sure to use the specified cloth only. Use the specified cloth adding only a little water. As the product may be scratched if there is any foreign material on the cloth, make sure to shake it thoroughly before using it.
When cleaning the product, do not spray water directly onto the main body of the product. Ensure that water does not enter the product and that it is not wet. Otherwise, this may result in electric shock, fire or a malfunction.

When using headphones or earphones, do not turn the volume too high. Having the sound too loud may damage your hearing.
If you continually move closer to the product screen, your eyesight may be failing.
To ease eye strain, take at least a five-minute break after every hour of using the monitor.
Do not install it in an unstable location such as an unstable rack or uneven surface or a location exposed to vibrations. Otherwise, it may fall and cause personal injury and/or damage the product. If you use the product in a location exposed to vibrations, it may damage the product and result in fire.
When moving the product, turn the power off and disconnect the power plug, antenna cable, and all the cables connected to the product. Otherwise, it may result in electric shock or fire.
Ensure that children do not hang onto the product or climb up onto the product. The product may fall and cause personal injury or death.
If you do not use the product for a long period of time, disconnect the power cord from the power outlet. Otherwise, this may result in overheating or fire due to dust, and may result in fire due to electric shock or leakage.
Do not place any heavy items or toys or confectionery, such as cookies etc. that may attract the attention of children and to the product. Your children may hang onto the product causing it to fall and this may result in personal injury or death.
Be careful that children do not place the battery in their mouths when removed from the remote control. Place the battery in a location that children or infants cannot reach. If children have had the battery in their mouths, consult your doctor immediately. When replacing the battery, insert it with right polarity (+, -). Otherwise, the battery may become damaged or it may cause fire, personal injury or damage due to leakage of the internal liquid.
Use only specified standard batteries. Do not use new and used batteries together. This may cause a battery to break or leak and may cause fire, injury, or contamination (damage).
The batteries (and rechargeable batteries) are not ordinary refuse and must be returned for recycling purposes. The customer is responsible for returning the used or rechargeable batteries for recycling. The customer can return used or rechargeable batteries to a nearby public recycling center or to a store selling the same type of the battery or rechargeable battery.
Do not turn the product upside down or move it while holding only the stand. Otherwise, it may fall and result in personal injury and/or damage to the product.
Do not place the product in a location exposed to direct sunlight or near any heat such as a fire or heater. This may reduce the lifetime of the product, and may result in fire.
Do not drop any objects onto the product or cause any impact to the product. Otherwise, this may result in electric shock or fire. Do not use a humidifier or kitchen table near the product. Otherwise, this may result in electric shock or fire.

When there is a gas leak, do not touch the product or the power plug but ventilate immediately. If a spark occurs, it may cause an explosion or fire.
If the product has been turned on for a long time, the display panel becomes hot. Do not touch it.
Be careful when adjusting the angle of the product or the height of the stand. This may result in personal injury as your hand or fingers may become caught. Also, if you tilt the product too far, it may fall and cause personal injury.
Do not install the product in a location low enough for children to reach. Otherwise, it may fall and result in personal injury. Since the front part of the product is heavy, install the product on a level and stable surface. Do not put any heavy objects on the product. This may result in personal injury and/or damage to the product.
Good Postures When Using the Monitor When using the product, use it in the correct position. Keep your back straight while looking at the product. The distance between your eyes and the screen should be between 45 to 50 cm. Look at the screen from a slightly higher location than the height of the screen. When using the product, use it in the correct position. Adjust the angle so that light is not reflected on the screen. Place your arms perpendicular to your sides and allow your arms to be level with the back of the hand. Keep your elbow at 90 degrees. Keep your knees at greater than 90 degrees, and keep your heels firmly on the floor. Keep your arms lower than your heart.

Introduction

Package Contents
Note Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Contact a local dealer to buy optional items.

Unpacking

Without stand

With stand

Monitor Manuals

Monitor

Quick Setup Guide
Warranty Card (Not available in all locations)

User's Guide

Cables
D-Sub Cable Sold separately

Power Cord

Stereo Cable

DVI Cable

HDMI Cable

Headphones

Sold separately

USB Cable

TV Antenna Cable (Coaxial Cable)
Component(PR, PB, Y) Cable

Audio cable

Digital audio optic output cable
Remote Control BN59-00678A
Batteries (AAA X 2) (Not available in all locations)

Cleaning Cloth

Cable holding ring Note

Stand Body

Stand Base
Cleaning Cloth is only provided for highly polished black products as a product feature.

Your Monitor Front

Activates a highlighted menu item. Push the ' ', button to change the input signal source.
Changing the source is only allowed for external devices connected to the product at the time. To switch Screen modes: [PC] [DVI] [TV] [Component] [HDMI1] [HDMI2] >> Click here to see an animation clip MENU Use this button to open the on-screen menu and to exit from the on-screen menu or to close the screen adjustment menu. - VOL+ Moves from one menu item to another horizontally or adjusts selected menu values. Adjusts the audio volume. - CH + Moves from one menu item to another vertically or adjusts selected menu values. In TV/DTV mode, selects TV/DTV channels. Power button [ ]
Use this button for turning the product on and off.
Note The button to the right of the monitor are touch-sensitive buttons. Touch a button lightly with your finger. Power indicator This light is lit when operating normally, and blinks once when your adjustments are saved. Note See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed or when leaving it unattended for long periods. Speaker
Note The configuration at the back of the product may vary from product to product.
POWER POWER Connect the power cord for your monitor to the POWER port on the back of the product.
PC Connect the PC terminal at the back of your monitor to your computer.
HDMI/PC/DVI-D AUDIO IN DIGITAL AUDIO OUT(OPTICAL) EX-LINK HDMI/PC/DVI-D AUDIO IN Connect the [ HDMI/PC/DVI-D AUDIO IN ] terminal at the back of your product to your computers sound card. DIGITAL AUDIO OUT(OPTICAL) Connect the [DIGITAL AUDIO OUT(OPTICAL)] terminal of your product to the digital sound output or standard sound output terminal of the DVD home theater (or amplifier) using a digital audio optical output cable. EX-LINK This is a reserved terminal used for servicing. SERVICE SERVICE This is a reserved terminal used for servicing.
DVI-D DVI-D Connect the DVI cable to the DVI-D port on the back of your product.

Kensington Lock

The Kensington Lock is a device used to physically fix the system when using it in a public place. The locking device has to be purchased separately. The appearance and locking method may differ from the illustration depending on the manufacturer. Refer to the manual provided with the Kensington Lock for proper use. The locking device has to be purchased separately. Note The location of the Kensington Lock may be different depending on its model.

Installing the Monitor Driver (Manual)
Microsoft Windows Vista Operating System 1. 2. Insert your Manual CD into your CD-ROM drive. Click (Start) and "Control Panel". Then, double-click on "Appearance and Personalization".
Click "Personalization" and then "Display Settings".
Click "Advanced Settings.".
Click "Properties" in the "Monitor" tab. If the "Properties" button is deactivated, it means the configuration for your monitor is completed. The monitor can be used as is. If the message "Windows needs." is displayed, as shown in the figure below, click "Continue".
Note This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage. 6. Click "Update Driver." in the "Driver" tab.
Check the "Browse my computer for driver software" checkbox and click "Let me pick from a list of device drivers on my computer".
Click "Have Disk. and select the folder (for example, D:\Drive) where the driver setup file is located, and click "OK".
Select the model that matches your monitor from the list of monitor models on the screen, and click "Next".
10. Click "Close" "Close" "OK" "OK" on the following screens displayed in sequence.
Microsoft Windows XP Operating System
Using the Software 1. 2. Insert CD into the CD-ROM drive. Click "Start" "Control Panel" then click the "Appearance and Themes" icon.
Click "Display" icon and choose the "Settings" tab then click "Advanced.".
Click the "Properties" button on the "Monitor" tab and select "Driver" tab.
Click "Update Driver." and select "Install from a list or." then click "Next" button.
Select "Don't search, I will." then click "Next" and then click "Have disk".
Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button.
If you can see following message window, then click the "Continue Anyway" button. Then click "OK" button.
Note This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ 9. Click the "Close" button then click "OK" button continually.

10. Monitor driver installation is completed. Microsoft Windows 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. 2. 3. Choose "OK" button on the "Insert disk" window. Click the "Browse" button on the "File Needed" window. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button.
How to install 1. 2. 3. 4. Click "Start", "Setting", "Control Panel". Double click the "Display" icon. Select the "Settings" tab and click "Advanced Properties" button. Choose "Monitor". Case1 : If the "Properties" button is inactive, it means your monitor is properly configured. Please stop installation Case2 : If the "Properties" button is active, click the "Properties" button then follow next steps continually. 5. 6. 7. 8. 9. Click "Driver" and then click on "Update Driver." then click on the "Next" button. Choose "Display a list of the known drivers for this device so that I can choose a specific driver" then click "Next" and then click "Have disk". Click the "Browse" button then choose A:(D:\Driver). Click the "Open" button, then click "OK" button. Choose your monitor model and click the "Next" button then click "Next" button.
10. Click the "Finish" button then the "Close" button. If you can see the "Digital Signature Not Found" window then click the "Yes" button. And click the "Finish" button then the "Close" button. Microsoft Windows Millennium Operating System 1. 2. 3. Click "Start", "Setting", "Control Panel". Double click the "Display" icon. Select the "Settings" tab and click "Advanced Properties" button.
Using the Software 4. 5. 6. 7. 8. 9. Select the "Monitor" tab. Click the "Change" button in the "Monitor Type" area. Choose "Specify the location of the driver". Choose "Display a list of all the driver in a specific location." then click "Next" button. Click the "Have Disk" button. Specify A:\(D:\driver) then click "OK" button.
10. Select "Show all devices" and choose the monitor that corresponds to the one you connected to your computer and click "OK". 11. Continue choosing "Close" button and "OK" button until you close the Display Properties dialogue box. Microsoft Windows NT Operating System 1. 2. 3. 4. Click "Start", "Settings", "Control Panel", and then double-click "Display" icon. In Display Registration Information window, click Settings Tab and then click "All Display Modes". Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and then click "OK". Click "Apply" button if you see the screen working normally after clicking "Test". If the screen is not normal, change to a different mode (lower mode of resolution, colors or frequency). Note If there is no Mode at All Display Modes, select the level of resolution and vertical frequency by referring to the Preset Timing Modes in the user guide. Linux Operating System To execute X-Window, you need to make the X86Config file, which is a type of system setting file. 1. 2. 3. 4. 5. 6. 7. 8. 9. Press "Enter" at the first and the second screen after executing the X86Config file. The third screen is for setting your mouse. Set a mouse for your computer. The next screen is for selecting a keyboard. Set a Keyboard for your computer. The next screen is for setting your monitor. First of all, set a horizontal frequency for your monitor. (You can enter the frequency directly.) Set a vertical frequency for your monitor. (You can enter the frequency directly.) Enter the model name of your monitor. This information will not affect the actual execution of X-Window.

Picture parameters are replaced with the factory default values. OK Cancel , , MENU,EXIT
Picture : TV / Component / HDMI Mode
The Monitor has three automatic picture settings ("Dynamic", "Standard", and "Movie") that are preset at the factory. You can activate either Dynamic, Standard, or Movie. Dynamic Selects the picture for high-definition in a bright room. Standard Selects the picture for optimum display in a normal environment. Movie Selects the picture for viewing movies in a dark room.
Backlight / Contrast / Brightness / Sharpness / Color / Tint
You can use the on-screen menus to change the contrast and brightness according to personal preference. Backlight : Adjust the screen brightness by adjusting the LCD backlight. Contrast : Adjust the Contrast. Brightness : Adjust the Brightness. Sharpness : Adjust the Sharpness. Color : Adjusts the picture color. Tint : Adds a natural tone to the display. , , , , MENU,EXIT
The tone of the color can be changed. Cool1 / Cool2 / Normal / Warm1 / Warm2
Note Warm1 or Warm2 is only activated when the picture mode is Movie. Settings can be adjusted and stored for each external device you have connected to an input of the TV. MENU , , MENU,EXIT
You can switch the Size. The direct button on the remote control is 'P.SIZE' button. Wide - A full screen is displayed regardless of the screen aspect ratio of the input signals. 16:9 - Sets the picture to 16:9 wide mode. Zoom1 - Magnifies the size of the picture on the screen. Zoom 2 - Magnifies the size of the picture more than Zoom1. Wide Fit - Enlarges the aspect ratio of the picture to fit the entire screen. 4:3 - Sets the picture to 4:3 normal mode. Just Scan - Use the function to see the full image without any cut off when HDMI (480i / 1080i), Component (480i / 1080i) or DTV(480i / 1080i) signals are input. ( Wide Fit and Just Scan are only operated in HDMI mode.) MENU , , , MENU,EXIT

- Digital NR

Digital Noise Reduction. If the broadcast signal received by your TV is weak, you can activate the Digital Noise Reduction feature to help reduce any static and ghosting that may appear on the screen. Off - Turns the screen noise reduction function off. Low - Reduces screen noise at a low level. Medium - Reduces screen noise at a medium level. High - Reduces screen noise at a high level. Auto - Automatically recognizes and reduces screen noise. MENU , , , MENU,EXIT

- HDMI Black Level

When a DVD or set-top box is connected to your TV via HDMI, it may cause a degradation in the screen quality, such as an increase in the black level, a low contrast, or discoloration, etc., depending on the external device connected. In this case, adjust the screen quality of your TV by configuring the HDMI Black Level. This function is active only when the an external device (DVD player, STB etc.) is connected to the TV via HDMI(RGB Signal). (Available in HDMI Mode Only) Normal / Low

- Film Mode

The Film Mode feature offers you a theater-quality viewing experience. Film mode is supported in TV, Component (480i / 1080i) and HDMI (480i / 1080i) Off / Auto MENU , , , MENU,EXIT

Sound Available Modes

PC / DVI TV

Adjusting the Monitor

Component HDMI Note
The default setting may different depending on the selected Input Mode (input signal source selected in External Input List) and the selected resolution.
The Monitor has a built-in high fidelity stereo amplifier. Standard Choose Standard for the standard factory settings. Music Choose Music when watching music videos or concerts. Movie Choose Movie when viewing movies. Speech Choose Speech when watching a show that is mostly dialogue (i.e., news). Custom Choose Custom if you want to adjust the settings according to personal preference. MENU , , MENU,EXIT

Equalizer

You can adjust the left and right sound balance and the low or high volume as required. MENU , , , , , MENU,EXIT
Multi-Track Options Preferred Language
You can select the audio language. (Available in DTV Mode Only) MENU , , , MENU,EXIT

Multi-Track Sound

Mono : Choose for channels that are broadcasting in mono or if you are having difficulty receiving a stereo signal. Stereo : Choose for channels that are broadcasting in stereo. SAP : Choose to listen to the Separate Audio Program, which is usually a foreign-language translation.
(Available in Analog TV Mode Only) MENU , , , MENU,EXIT

Auto Volume

Reduces the differences in volume level among broadcasters. Off On , , , MENU,EXIT

TV Speaker

If you set this menu "On", sound output from the speakers is muted in case of using the home theater. Off On , , , MENU,EXIT

Symptoms and Recommended Actions
Note A monitor recreates visual signals received from the computer. Therefore, if there is trouble with the computer or the video card, this can cause the monitor to become blank, have poor coloring, noise, Video mode not supported, etc. In this case, first check the SOURCE of the problem, and then contact a service center or your dealer. 1. Check if the power cord and the video cables are properly connected to the computer. 2. Check if the computer beeps more than 3 times when booting. (If it does, request an after-service for the main board of the computer.) 3. If you installed a new video card or if you assembled the PC, check if you installed the adapter (video) driver and the monitor driver. 4.Check if the scanning ratio of the video screen is set at 56 Hz ~ 75 Hz. (Do not exceed 60 Hz when using the maximum resolution.) 5. If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode, remove the Display Adapter at the "Control Panel, System, Device Administrator" and then reboot the computer to reinstall the adapter (video) driver.

Check List

Note Before calling for assistance, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer.
1. Problems related to Installation
Note Problems related to the monitor installation and their solutions are listed.

PC Mode

Q: A: Q: A: It appears the PC does not function normally. Check if the Display Adapter Driver (VGA Driver) is properly installed. (Refer to Installing Driver) The monitor screen flickers. Check if the signal cable between the computer and the monitor is securely connected and tightened.(Refer to Connecting the monitor)

TV Mode

Q: A: Q: A: TV screen is blurred or shows noise signals. Check if the TV antenna connector is securely connected to the external antenna.(Refer to Connecting TV) TV signal is not received Select "Auto Program" to configure the channel system automatically. (Refer to the Auto Program)
2. Problems related to Screen
Note Problems related to the monitor screen and their solutions are listed. Q: A: Q: A: A: Q: A: A: Q: A: Q: A: A: A: Screen is blank and power indicator is off Ensure that the power cord is firmly connected and the LCD monitor is on.(Refer to the Connecting the monitor) "Check Signal Cable" message Ensure that the signal cable is firmly connected to the PC or video SOURCEs.(Refer to the Connecting the monitor) Ensure that the PC or video SOURCEs are turned on. "Not Optimum Mode" message Check the maximum resolution and the frequency of the video adapter. Compare these values with the data in the Preset Timing Modes Chart. Picture rolls vertically. Check if the signal cable is securely connected.Connect it again securely. (Refer to Connecting the monitor) Image is not clear. Picture is blurred. Run Frequency Coarse and Fine tuning. Turn on again after removing all accessories (video extension cable, etc.) Set resolution and frequency to the recommended ranges.

PowerSaver

This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature. State Power Indicator Power Consumption Normal Operation Power saving mode Power off (Power button) EPA/ENERGY 2000 On Less than50 watts Blinking Less than 2 watts Off Less than 1 watts
This monitor is EPA ENERGY STAR compliant and ENERGY2000 compliant when used with a computer equipped with VESA DPM functionality. As an ENERGY STAR Partner, SAMSUNG has determined that this product meets the ENERGY STAR guidelines for energy efficiency.

Preset Timing Modes

If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows. Display Mode Horizontal Frequency (kHz) 31.469 31.469 31.469 35.000 49.726 68.681 37.861 37.500 35.156 37.879 48.077 46.875 48.363 56.476 60.023 67.500 60.000 63.981 79.976 65.290 Vertical Frequency (Hz) 70.086 59.940 70.087 66.667 74.551 75.062 72.809 75.000 56.250 60.317 72.188 75.000 60.004 70.069 75.029 75.000 60.000 60.020 75.025 59.954 Pixel Clock (MHz) 25.175 25.175 28.322 30.240 57.284 100.000 31.500 31.500 36.000 40.000 50.000 49.500 65.000 75.000 78.750 108.000 108.000 108.000 135.000 146.250 Sync Polarity (H/V) +/-/-/+ -/-/-/-/-/+/+ +/+ +/+ +/+ -/-/+/+ +/+ +/+ +/+ +/+ -/+
IBM, 640 x 350 IBM, 640 x 480 IBM, 720 x 400 MAC, 640 x 480 MAC, 832 x 624 MAC, 1152 x 870 VESA, 640 x 480 VESA, 640 x 480 VESA, 800 x 600 VESA, 800 x 600 VESA, 800 x 600 VESA, 800 x 600 VESA, 1024 x 768 VESA, 1024 x 768 VESA, 1024 x 768 VESA, 1152 x 864 VESA, 1280 x 960 VESA, 1280 x 1024 VESA, 1280 x 1024 VESA, 1680 x 1050

603 800-810-5858 010-6475 1880
http://www.samsung.com http://www.samsung.com

HONG KONG INDIA

3698 - 110011
http://www.samsung.com/hk http://www.samsung.com
INDONESIA JAPAN MALAYSIA NEW ZEALAND PHILIPPINES SINGAPORE THAILAND
0800-112-8888 0120-327-527 1800-88-SAMSUNG(726-7864) 1800-SAMSUNG(726-7864) 1800-29-3232, 02-689-3232
http://www.samsung.com http://www.samsung.com/jp http://www.samsung.com/my http://www.samsung.com/nz http://www.samsung.com http://www.samsung.com
1800-10-SAMSUNG(726-7864) http://www.samsung.com/ph
Asia Pacific TAIWAN VIETNAM 0800-329-889 Middle East & Africa SOUTH AFRICA TURKEY U.A.E 0860-SAMSUNG(726-7864) 11 800-SAMSUNG(726-7864) 8000-4726 http://www.samsung.com http://www.samsung.com http://www.samsung.com http://www.samsung.com/tw http://www.samsung.com
Sync Signal Sync (Synchronized) Signals refer to the standard signals that are required to display desired colors on the monitor. They are divided into Vertical and Horizontal Sync Signals. These signals display normal color images by the set resolution and frequency. Separate Composite

Types of Sync Signals

This is a scheme of transmitting individual vertical and hori sync signals to the monitor.
This is a scheme of combining vertical and horizontal syn nals into one composite signal and transmitting it to the mo The monitor displays the color signals by separating the co site signal into original color signals.

Dot Pitch

The image on a monitor is composed of red, green and blue dots. The closer the dots, the higher the resolution. The distance between two dots of the same color is called the 'Dot Pitch'. Unit: mm The screen must be redrawn several times per second in order to create and display an image for the user. The frequency of this repetition per second is called the Vertical Frequency or Refresh Rate. Unit: Hz Example: If the same light repeats itself 60 times per second, this is regarded as 60 Hz.

Vertical Frequency

Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle. The inverse number of the Horizontal Cycle is called Horizontal Frequency. Unit: kHz Showing the horizontal lines of the screen from the top to the bottom sequentially is called the Non-Interlace method while showing odd lines and then even lines in turn is called the Interlace method. The Non-Interlace method is used for the majority of monitors to ensure a clear image. The Interlace method is the same as that used in TVs. This is a function that provides the best quality screen for the user by allowing the computer and the monitor to exchange information automatically. This monitor follows the international standard VESA DDC for the Plug & Play function. The number of horizontal and vertical dots used to compose the screen image is called the 'resolution'. This number shows the ac-