If the LCD Display is dropped or the casing is damaged, turn the LCD Display off and unplug the power cord. Then contact the Service Center.
The LCD Display may malfunction, causing electric shock or fire.
Disconnect the plug from the outlet during storms or lightning or if it is not used for a long period of time.
Failure to do so may cause electric shock or fire.
Do not try to move the LCD Display by pulling only the wire or the signal cable.
This may cause a breakdown, electric shock or fire due to damage to the cable.
Do not move the LCD Display right or left by pulling only the wire or the signal cable.
Do not cover the vents on the LCD Display cabinet.
Bad ventilation may cause a breakdown or fire.
Do not place water containers, chemical products or small metal objects on the LCD Display.
This may cause a malfunction, electric shock or fire. If a foreign substance enters the LCD Display , unplug the power cord and contact the Service Center.
Keep the product away from combustible chemical sprays or inflammable substances.
This may cause an explosion or fire.
Never insert anything metallic into the LCD Display openings.
This may cause electric shock, fire or injury.
Do not insert metal objects such as chopsticks, wire and tools or inflammable objects such as paper or matches into the vent, headphone port or AV ports or etc.
This may cause electric shock or fire. If an alien substances or water enters the product, turn the product off, unplug the power connector from the wall
outlet and contact the Service Center.
When viewing a fixed screen for an extended period of time, residual image or blurriness may appear.
Change the mode to energy saving mode or set a screensaver to a changing picture when away from the LCD Display for an extended period of time.
Adjusts the resolution and frequency to the level appropriate for the model.
An inappropriate resolution may cause undesirable picture quality. 32 inch (80 cm) - 1360 X 768
Viewing the LCD Display continuously at a too close angle may result in damage to your eyesight.
To ease eye strain, take at least a five-minute break after every hour of using the LCD Display.
Do not install the product on an unstable, uneven surface or a location prone to vibrations.
Dropping the product may cause damage to the product or the person carrying it. Using the product in a location prone to vibrations may shorten the lifetime of the product or may cause the product to catch fire.

S.MODE

When pressing this button, the current mode is displayed at the bottom centre of the screen. The LCD Display has a built-in high fidelity stereo amplifier. Then press the button again to circle through available preconfigured modes. ( Standard Music Movie Speech Custom )

21) STILL

Press the button once to freeze the screen. Press it again to unfreeze.

22) FM RADIO

Turns the FM Radio on/off. In PC/DVI mode, sets the SOUND to FM Radio. In general Video mode, selects FM Radio, and turns off the screen. In areas where the signal is weak, noise may occur during FM radio broadcasts. - This fuction does not work for this monitor.

23) P.SIZE

Press to change the screen size.
DUAL/MTS DUALSTEREO/MONO, DUAL l / DUAL ll and MONO/NICAM MONO/NICAM STEREO can be operated depending on the broadcasting type by using the DUAL button on the remote control while watching TV.
MTSYou can select MTS (Multichannel Television Stereo) mode.

Audio Type MTS/S_Mode

Mono Mono Mono Stereo Mono SAP

Default

Manual Change Mono

FM Stereo

Stereo SAP
- This fuction does not work for this monitor.
Every time you press the button, a PIP screen appears.
Changes the source of the PIP window signal.

28) SWAP

Swaps the contents of the PIP and main image. The image in the PIP window will appear on the main screen, and the main screen image will appear in the PIP window.
Switches the PIP Picture Size.

Rewind

PLAY / PAUSE

Play/Pause

Fast forward 1995~2007 SAMSUNG. ALL Right Reserved

SyncMaster 400PX/460PX

User's Guide, MDC Software
Switches from PC mode to Video mode. Changing the source is only allowed for external devices that are connected to the LCD Display at the time. [PC] [BNC] [DVI] [AV] [S-Video] [Component] >> Click here to see an animation clip.

17) Kensington Lock

1. ON / OFF 2. MAGICNET 3. MDC 4. LOCK 5. MagicNet buttons 6.+100 -/-7. VOL 8. MUTE
9. TTX/MIX 10. MENU 11. ENTER 12. P.MODE 13. AUTO 14. PRE-CH 15. CH/P 16. SOURCE 17. INFO 18. EXIT 19. Up-Down Left-Right buttons 20. S.MODE 21. STILL 22. FM RADIO 23. P.SIZE

There are two hinges(left and right). Use the correct one. Before drilling into the wall, check if the length between the two locking holes at the back of the product is correct. If the length is too short or long, loosen all or some of the 4screws on the wall bracket to adjust the length. A. Length between the two locking holes
Check the installation diagram and mark the drill points on the wall. Use the 5.0 mm bit to drill holes deeper than 35 mm. Fix each anchor in the corresponding hole. Match each of the brackets and hinge holes to the corresponding anchor holes and insert and tighten the 11 screws A.
To mount the product on the wall bracket
The shape of the product may vary depending on the model. (The assemblies of the plastic hanger and the screw are the same)
Remove the 4 screws on the back of the product.
Insert the screw B into the plastic hanger.
1. Mount the product on the wall bracket and make sure it is properly fixed to the left and right plastic hangers. 2. Be careful when installing the product on the bracket as fingers can be caught in the holes. 3. Make sure the wall bracket is securely fixed to the wall, or the product may not stay in place after installation. Tighten the 4 screws in step 2 (plastic hanger + screw B)to the rear holes of the product.
Remove safety pin (3) and insert the 4 product holders into the corresponding bracket holes (1). Then place the product(2) so that it is firmly fixed to the bracket. Make sure to re-insert and tighten the safety pin (3) to securely hold the product to the bracket. A. Monitor B. Wall Bracket C. Wall
Wall Bracket Angle Adjustment
Adjust the bracket angle to -2before installing it on the wall.
1. Fix the product to the wall bracket. 2. Hold the product at the top in the center and pull it forward (direction of the arrow) to adjust the angle. 3. You can adjust the bracket angle between -2and 15.
Make sure to use the top center, and not the leftor the right side of the product to adjust the angle.

SyncMaster 460PXn/460PX

Model Safety Instructions Introduction Connections
Installing the Stand KIT Connecting the LCD Display
Using the Software Adjusting the LCD Display Troubleshooting Specifications Information Appendix Dodatak

Select Component for the connection to a DVD player using the SOURCE button on the front of the LCD Display or on the remote control.
Then, start the DVD Player with a DVD disc inserted. Note
A component cable is optional. For an explanation of Component video, consult your DVD manual.
Connecting to a Camcorder
Locate the A/V output jacks on the camcorder. They are usually found on the side or back of the camcorder. Connect a set of audio cables between the AUDIO OUTPUT jacks on the camcorder and the AV AUDIO IN [L-AUDIO-R] on the LCD Display.
Connect a video cable between the VIDEO OUTPUT jack on the camcorder and the AV IN [VIDEO] on the LCD Display.
Select AV for the Camcorder connection using the SOURCE button on the front of the LCD Display or on the remote control.
Then, start the Camcorders with a tape inserted. Note
The audio-video cables shown here are usually included with a Camcorder.
(If not, check your local electronics store.) If your camcorder is stereo, you need to connect a set of two cables.
Connecting to a DTV Set Top Box
Note The connections for a typical Set Top Box are shown below.
Connect a set of audio cables between the COMPONENT AUDIO IN [L-AUDIO-R] on the LCD Display and the AUDIO OUT jacks on the Set Top Box.
Connect a Component cable between the BNC / COMPONENT IN - PR, Y, PB port on the LCD Display and the PR, Y, PB jacks on the Set Top Box.
Select Component for the connection to a DTV Set Top Box using the SOURCE button on the front of the LCD Display or on the remote control. Note
For an explanation of Component video, see your Set Top Box owner's manual.

Connecting Speakers

Fasten the SET and the speaker using the screws. * Mount the speaker set without the speaker stand.
Connect the speaker connection cable between the speaker connection jack on the back of the SET and
the speaker connection jack on the back of the speaker. Note Do not move the SET while the SET is connected to the speakers. The speaker-bracket for connecting the SET speaker my become damaged.
Connecting to an Audio System
Connect a set of audio cables between the AUX L, R jacks on the AUDIO SYSTEM and the AUDIO OUT [L-AUDIO-R] on LCD Display.

Connecting a LAN Cable

Connect the LAN cable.

Connecting a USB device

You can connect USB devices such as a mouse or keyboard.

Using a USB Holder

When using a small external device such as a portable memory stick and it is connected to the USB terminal at the back of your monitor, it is exposed to the possiblity of theft or loss. By installing a USB holder after the installation of an external device, you can prevent theft or loss.

2. Allows you to enable or disable the remote control signal receiving function of the display unit. 3. Set the Safety Lock function. When setting the Lock function, you can only operate power and lock buttons on the remote control and set. 4. The setting for the PC Serial Port can change. The original value is COM1. 5. Click Select all or Clear to select or clear all displays. 6. Use Grid to view brief information on selected display. 7. Select a display from Display Selection. 8. Use Control Tools to control displays. <Note> The remote control Enable/Disable function operates whether or not the power is On/Off, and this applies to all displays connected to the MDC. However, regardless of the status at the time the MDC is shut down, the remote control signal receiving function of all displays is initialized to Enable when the MDC is closed.

Port Selection

1. The Multiple Display Control is originally set to COM1. 2. If any port other than COM1 is used, COM1 through COM4 can be selected in the Port Selection Menu. 3. If the exact port name that is connected to the LCD Display using a serial cable is not selected, communication will be unavailable. 4. The selected port is stored in the program and used for the next program as well.

Power Control

1. Click Power Control of the main icons and the Power Control screen appears.
Info Grid shows some basic information necessary to Power Control. 1) (Power Status) 2) Input 3) Image Size 4) On Timer 5) Off Timer 2. Use the Select All button or Check Box to choose a display to control.
Power Control allows controlling some of the functions of the selected display. 1) Power On/Off
- Turns the power of the selected display On/Off. 2) Volume - Controls the volume level of the selected display. It receives the volume value of the selected display from the sets and displays it in the slider. (When you cancel the selection or choose Select All, the value returns to the default value 10) 3) (Mute On/Off) - Turns on/off the Mute function of the selected display. When selecting one set at a time, turn on the Mute function for the selected set. The Mute function is disabled automatically when you adjust the volume level. (The values return to the default settings when you undo the selections or choose "Select All".) The Power Control feature is available for all displays. The Volume Control and Mute features are available only for the displays whose power status is ON.

Input Source

1. Click Input Source of the main icons and the Input Source control screen appears. Click Select All or use Check Box to select a display to control. TV Mode

PC Mode

Info Grid shows some basic information necessary to Input Source Control. 1) PC - Changes the Input Source of the selected display to PC. 2) BNC - Changes the Input Source of the selected display to BNC. 3) DVI - Changes the Input Source of the selected display to DVI. 4) TV - Changes the Input Source of the selected display to TV. 5) AV - Changes the Input Source of the selected display to AV. 6) S-Video - Changes the Input Source of the selected display to S-Video. 7) Component - Changes the Input Source of the selected display to Component. 8) MagicNet - The Input source of MagicNet works only on MagicNet model. 9) Channel - Channel arrow appears when the Input Source is TV. TV Source can be selected only in products with TV and controlling channels is allowed only when Input Source is TV. The Input Source Control feature is available only for the displays whose power status is ON.

File Information This will display the name, date, size and resolution of the current file.
MagicNet/Network On/Off Status or Image Selection Menu Displays the On and Off status for the power and the network. Selecting an image file will change to the appropriate image menu.

Extended Image Menu

Slide Show
When the files are selected in the library list : Sequentially displays the image files registered to the library. When monitoring information is being played from a schedule : Displays the image files registered to the schedule. When monitoring the information which the monitor user is selecting and playing : This function is disabled. When the files are selected in the library list : Displays the previous file. When monitoring information is being played from a schedule : Displays the previous file. If a slide show is in progress, the slide show is stopped. When monitoring the information which the monitor user is selecting and playing : This function is disabled. When the files are selected in the library list : Displays the next file. When monitoring information is being played from a schedule : Displays the next file. If a slide show is in progress, the slide show is stopped. When monitoring the information which the monitor user is selecting and playing : This function is disabled. When the files are selected in the library list : Stops the slide show. When monitoring information is being played from a schedule : Stops the slide show. When monitoring the information which the monitor user is selecting and playing : This function is disabled. Enlarges/shrinks an image file to fit to the full screen. Double-click the screen to return to the original image size.

Prv (Previous)

Nxt (Next)

Full Screen

Play Control Tool Controls for play, stop, next file, previous file, and volume when playing a movie or audio file.

Play / Pause

When the files are selected in the library list : Plays the audio/movie files registered with the library list. When monitoring information is being played from a schedule : Plays the audio/movie files registered with the schedule. When monitoring the information which the monitor user is selecting and playing : This function is disabled. When the files are selected in the library list : Stops playing an audio/movie file. When monitoring information is being played from a schedule : This function is disabled. When monitoring the information which the monitor user is selecting and playing : This function is disabled. When the files are selected in the library list : Plays the previous/next file in the library list. When monitoring information is being played from a schedule : Plays the previous/next file in the schedule list. When monitoring the information which the monitor user is selecting and playing : This function is disabled.

AV S-Video Component TV : Supportable for SyncMaster 400TXn only Position Select a position. (LeftTop) (RightTop) (LeftBot) (RightBot) Swap
Setting 1. Sound Mode Standard Music Movie Speech Custom Bass, Treble, Balance 2. Sound Option SRS TSXT ON/OFF Sound Select Main/Sub 3. Image Lock Coarse -/+ Fine -/+ Position Auto Adjustment 4. Siganal Balance Signal Balance ON/OFF Phase R : 0 ~ 100 Phase G : 0 ~ 100 Phase B : 0 ~ 100 Gain : 0 ~ 100 Sharpness : 0 ~ 100
Maintenanace Lamp Control You can control the intensity of the lamp. (Auto/Manual is available. When Auto is running, Manual is off; and when Manual is running, Auto is off.) In Auto mode, the lamp is adjusted to the previously set value at the set time. In Manual, the previous value is maintained. Auto - Hour, Minute, am/pm, Value Manual - 0 ~ 100
Safety Screen The Safety Screen function is used to prevent afterimages that may appear when a still picture is displayed on the screen over a long time. - The Screen Scroll function scrolls the screen for the specified period of time. - This function is not available when the power is turned off. Interval Second Type Video Wall This offers a function that enables you to use several monitors as one screen. First, select the button that sets the number of monitors to be used and their allocation. The allocation figure will appear as a selectable button on the side. For example, when you choose 2*2, selectable buttons in the form of 2 rows and 2 lines appear, and if you select number 3 in this matrix, the third screen of the output screen divided by 4 will show up in the monitor. - The MDC program supplied by Samsung supports over 4*4. 1*2 2*1 2*2 3*3 4*4 1*5 5*1 OFF Format - Full, Natural Safety Lock Safety Lock ON/OFF
When entering a message to the server and setting the options needed before sending it, the message is displayed on the selected client monitor.
Unavailable while the source is being displayed. The Transparent Ticker is only available when the client is in Landscape mode.

Display Option

Normal: Outputs fixed sentences one by one. Scroll : Text scrolls. Trancparency : Sets the text background to transparent. Opaque : Sets the text background to opaque. Scroll and transparency are only applicable for the SyncMaster 320PXn/400P(T)Xn/460PXn.
Display Period Start Stop Clear Font Position
Marked in hours and minutes. Displays a message on the selected monitor. Stops displaying a message on the selected monitor. Allows you to change the text in the message edit box. Allows you to specify the point size, text color and background color. Displays the text at the top or bottom.
Login / Logout Change Password Option Help
Login / Logout Before using MagicNet, you first need to login. After a successful login, the Login button changes to a Logout button. A successful login is required to use the majority of functions. When installing MagicNet for the first time, the administrator account is provided on the basis of the password entered by the user. When adding an account, you can select from among three account types, and the selected account type decides the scope of using MagicNet. You may modify or delete the accounts of existing users as well as adding new users.
Account Type Administrator
Scope You have the authority to use all MagicNet functions. You are not authorized to use the Options menu and the Update function of MagicNet. You are not authorized to use the right mouse button click in the Library Registration, Options menu, MDC and Monitor List from among the MagicNet functions.

Power User

Operator

User Name Password

Change Password You can change your password in the login status. Enter your password correctly before logging in. You will be prompted to enter the password for installing MagicNet, and this password will become the default password for the administrator account. If you forget the password, please remove the program and re-install it. Old Password New Password Confirm Password
Option 1. Server Name In the Options, you can specify the server name for the connection information. The servers and monitors are connected via the network, and have proper names to identify each other. For a normal connection, the server name between a server and monitor must match. In other words, when the name of a server is MagicNet, only monitors whose server names are set to "MagicNet" can be connected to that server and receive the schedule. When there is no server with that name set in the monitor, it will wait until a server that matches this name appears. However, when the auto connction function is ON, it tries to connect to any server, and will connect to the server that replies first. Server Name 2. User Account When installing MagicNet for the first time, the administrator account is provided on the basis of the password entered by the user. When adding an account, select from among three account types, and the selected account type decides the scope of using MagicNet. You may modify or delete the accounts of existing users as well as adding new users.

1) On 2) Off

Video Wall
A Video Wall is a set of video screens connected together, so that each screen shows a part of the whole picture or where the same picture is repeated on each screen. When the Video Wall is on, you can adjust the Video Wall screen setting.

1) Video Wall

[MENU] [ / ] [ENTER] [ / ] [ENTER] [ENTER] [ / ] [ENTER] Turns Off/On the Video Wall function of the selected display Off/On. - Off - On

2) Format

[MENU] [ / ] [ENTER] [ / ] [ENTER] [ / ] [ENTER] [ / ] [ENTER] The format can be selected to see a divided screen. - Full Provides a full screen without any margins. - Natural Displays a natural image with the original aspect ratio intact.

3) Screen Divider

[MENU] [ / ] [ENTER] [ / ] [ENTER] [ / ] [ENTER] [ / ] [ENTER] The screen can be divided into several images. A number of screens can be selected with a different layout when dividing. Select a mode in Screen Divider. Select a display in Display Selection. The selection will be set up by pressing a number in the selected mode. - 2x2 - 3x3 - 4x4 - 5x5 - 1x2 - 2x1 - 1x5 - 5x1 Note When Video Wall is running, the PIP, Auto Adjustment, Image Lock, and Size functions are not available. Launching Video Wall while PIP is running, will switch PIP Off. Video Wall does not operate in MagicNet mode.

Safety Screen

The Safety Screen function is used to prevent afterimages that may appear when a still picture is displayed on the screen over a long time. - The Screen Scroll function scrolls the screen for the specified period of time. - This function is not available when the power is turned off.

1) Safety Screen

[MENU] [ / ] [ENTER] [ / ] [ENTER] [ENTER] [ / ] [ENTER] Determines whether to turn the Screen Scroll function Off or On. - Off - On

2) Interval

[MENU] [ / ] [ENTER] [ / ] [ENTER] [ / ] [ENTER] [ / ] [ENTER] Determines the time interval to run the Screen Scroll operation. (1~10 Hour) The time is calculated on the basis of the power on time. By default, the time is set to 10 hours. - 1~10 Hour

3) Interval

Controls the time intervals between image files for a slide show. (5 Sec, 10 Sec, 20 Sec, 30 Sec, 60 Sec)

4) Rotation

Displays an image file by turning it clockwise by 90 degrees.

5) Zoom

Displays a reduced picture.

6) Close

Closes the image control Menu.
The MP3 file format is supported.
The MPEG1, WMV file format are supported.

1) Play

Plays a movie file.

2) Full Size

Plays a movie file in full screen.

OFFICE / HTML

PPT(Power Point), DOC(MS Word), XLS(MS Excel), PDF, HTML, HTM files are displayed. * Install the proper viewer(freeware) program to see the MS Office(Word, Excel, Power Point) or PDF doucuments.

Connects to the Internet

Sets various functions in MagicNet mode. A password must be entered to access Setup mode.

1) Schedule View

Displays a schedule.

2) TCP/IP

Changes the TCP/IP settings.

3) Connection

Modifies the network settings.

4) Password

The password can be changed. The password should be between 6 and 12 characters in numeric format. (You should enter a password between 6 and 12 characters in numeric format) If you enter the wrong password three times, the setup configuration is reset and a warning message appears from the server. If you forget the password, enter Info, 8, 2 and 4 on the remote control to initialize the password. This
will reset the previous settings of Setup mode.

5) File

Local : You can delete or copy files on both local and removable disks.

6) Play Option

You can set the repeat play and screen settings. Repeat : Determines the repeat option for playing movies and music. None - Select No Repeat to play a movie or tune in the list only once. File Repeat - Select Repeat File to play a movie or tune in the list repeatedly. List Repeat - Select Repeat List to play movies or tunes in the list in sequence repeatedly. Rotation - Sets the picture orientation. Landscape - Sets the screen resolution to 1366x768 pixels. Portrait - Sets the screen resolution to 768x1366 pixels. EWF(Enhanced Write Filter) : Prevents change to and loss of the data saved on the disk. Disable - Disables EWF to allow saved data to be changed data on the protected disk (drive C:). When switching from the Enable to the Disable state, you can select Commit. Enable - Enables EWF to prevent saved data to be changed on the protected disk (drive C:). Commit - Commit the changed data to the protected disk (drive C:) when EWF is in the Enable state. Commit is not available when EWF is in the Disable state.

Specifications Information Appendix Dodatak

Self-Test Feature Check

Note Check the following items yourself before calling for assistance. Contact a Service Center for problems that you cannot solve by yourself.
Your LCD Display provides a self test feature that allows you to check whether your LCD Display is functioning properly. 1) 2) 3) Turn off both your computer and the LCD Display. Unplug the video cable from the back of the computer. Turn on the LCD Display. The figure shown below ("Check Signal Cable") appears on a black background when the LCD Display is working normally even though no video signal is detected: While in the Self-Test mode, the LED power indicator remains green and the figure moves around on the screen.
Turn off your LCD Display and reconnect the video cable; then turn on both your computer and the LCD Display
If your LCD Display screen remains blank after using the previous procedure, check your video controller and computer system; your LCD Display is functioning properly.

Not Optimum Mode

You can even view the screen at a resolution of 1360X768. However, you will receive the following message for a minute; You can choose to change the screen resolution or stay in the current mode during that time. And if the resolution is more than 85Hz, you will see the black screen because the LCD Display does not support over 85Hz.
Note Refer to Specifications > Preset Timing Modes for the resolutions or frequencies supported by the LCD Display.

Maintenance and Cleaning

Maintaining the LCD Display Case. Clean with a soft cloth after disconnecting the power cord. Do not use benzene, thinner or other flammable substances, or a wet cloth. We recommend that a Samsung cleansing agent is used to prevent damage to the screen.
Maintaining the Flat Panel Display Screen. Clean with a soft cloth (cotton flannel) smoothly. Never use acetone, benzene or thinner. (They may cause flaws or deformation of the screen surface.) The user will be required to pay costs and related expenses for repairing damages caused.
Symptoms and Recommended Actions
Note A LCD Display recreates visual signals received from the computer. Therefore, if there is a problem with the computer or the video card, this can cause the LCD Display to become blank, have poor coloring, become noisy, and video mode not supported, etc. In this case, first check the source of the problem, and then contact a Service Center or your dealer.

SyncMaster 400PX

Model Name SyncMaster 400PX
This monitor has a built -in power management system called PowerSaver. This system saves energy by switching your monitor to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPMS compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature.

Green Less than 210 W

IBM, 640 x 350 IBM, 640 x 480 IBM, 720 x 400 MAC, 640 x 480
70.086 59.940 70.087 66.667
31.469 31.469 31.469 35.000
25.175 25.175 28.322 30.240

+/ -/-/+ -/-

MAC, 832 x 624 VESA, 640 x 480 VESA, 640 x 480 VESA, 640 x 480 VESA, 800 x 600 VESA, 800 x 600 VESA, 800 x 600 VESA, 800 x600 VESA, 800 x600 VESA, 1024 x 768 VESA, 1024 x 768 VESA, 1024 x 768 VESA, 1024 x 768 VESA, 1360 x 768
49.726 37.861 37.500 43.269 35.156 37.879 48.077 46.875 53.674 48.363 56.476 60.023 68.677 47.712
74.551 72.809 75.000 85.008 56.250 60.317 72.188 75.000 85.000 60.004 70.069 75.029 85.997 60.000
57.284 31.500 31.500 36.000 36.000 40.000 50.000 49.500 56.250 65.000 75.000 78.750 94.500 85.500
-/-/-/-/+/+ +/+ +/+ +/+ +/+ -/-/+/+ +/+ +/+

SyncMaster 460PXn

Model Name SyncMaster 460PXn
Size Display area Pixel Pitch 46 " Diagonal (125.1 cm) 1018.353 mm (H) x 572.544 mm (V) 0.7455 mm (H) x 0.2485 mm (W)
1.102 x 658 x 126.5mm / 43.4 x 25.9 x 5.0 inch / 28 Kg / 61.6 lbs (without Stand) 1.102 x 715 x 293 mm / 43.4 x 28.1 x 11.5 inch / 30 Kg / 66 lbs (with Stand)

Green Less than 310 W

SyncMaster 460PX
Model Name SyncMaster 460PX

Green Less than 290 W

Model Safety Instructions Introduction Connections Using the Software Adjusting the LCD Display Troubleshooting Specifications Information
For Better Display PRODUCT INFORMATION (Image Retention Free)

Appendix

Information

For Better Display

Adjust the computer resolution and screen inection rate (refresh rate) on the computer as described below to enjoy the best picture quality. You can have an uneven picture quality on screen if the best picture quality is not provided for TFT-LCD. Resolution: 1360 x 768 Vertical frequency (refresh rate): 60 Hz
TFT LCD panels manufactured by using advanced semiconductor technology with a precision of 1ppm (one millionth) and above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality and you can use it without any problems. For example, the number of TFT LCD sub pixels contained in this product are 3,133,440

The best way to protect your monitor from Image retention is to turn Power off, or set your PC, or System to operate a Screen Saver program when you are not using it. Also Warranty service will be limited based on instruction guide.
Apply the Screen Scroll function on Product Apply the Screen Scroll function - Symptom: Horizontal Bar with Black Color move up and down.
- Select method. Instruction Guide : OSD Menu -> Set Up -> Safety Screen -> Screen Scroll. Time Interval : 1 ~ 10 hours ( Recommend : 1 ). Time Period : 1 ~ 5 second ( Recommend : 5 )
Note ( Please check CD's User Guide at "OSD Function", some model's will not available )
Apply the Screen Pixel function on Product
Apply the Screen Pixel function - Symptom: Dot with Black Color move up and down.
- Select method. Instruction Guide : OSD Menu -> Set Up -> Safety Screen -> Pixel. Time Interval : 1 ~ 10 hours ( Recommend : 1 ). Time Period : 10 ~ 50 second ( Recommend : 50 ) Apply the Screen Bar function - Symptom: Horizontal / Vertical Bar with Black Color move up and down.
- Select method. Instruction Guide : OSD Menu -> Set Up -> Safety Screen -> Bar. Time Interval : 1 ~ 10 hours ( Recommend : 1 ). Time Period : 10 ~ 50 second ( Recommend : 50 )
Note ( Please check CD's User Guide at "OSD Function", some model's will not available. )
Apply the Screen Erasing function on Product Apply the Screen Erasing function - Symptom: 2 Vertical blocks move with erasing the display
- Select method. Instruction Guide : OSD Menu -> Set Up -> Safety Screen -> Eraser. Time Interval : 1 ~ 10 hours ( Recommend : 1 ). Time Period : 10 ~ 50 second ( Recommend : 50 )
Model Safety Instructions Introduction Connections Using the Software Adjusting the LCD Display Troubleshooting Specifications Information Appendix
Contact SAMSUNG WORLDWIDE
Contact SAMSUNG WORLDWIDE Terms Correct Disposal Authority
Note If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center.
North America U.S.A CANADA MEXICO
1-800-SAMSUNG (7267864) 1-800-SAMSUNG (7267864) 01-800-SAMSUNG (7267864) http://www.samsung.com http://www.samsung.com/ca http://www.samsung.com/mx

Samsung Plasma Display | 3 + 1

VMBL0609CA02HQ-WW

Distributed by
Design and Specifications are subject to change without notice. Trademarks of other companies mentioned in these publications are hereby recognized and acknowledged.
imagine collective impact
Enter the pathway to success guided by Samsung LCD Monitor

LCD Display 200609

Business Display

Public Display

Prestigious Display
All the visions are focused on the display and the world come together before you
Large displays have become a necessity in public places like airports, train stations and shopping malls for quick and correct information delivery. Samsung has taken notice of such demands, and is planning to take the lead in the global large display market with its new multi-functional LCD display featuring the world's best picture quality of 1200:1 contrast ratio, 500 cd/m2 brightness and fast response time of 8 ms (400PXn). By providing an internal network solution without additional options, Samsung's new display (400PXn,

Samsung LCD Display

460PXn, 400TXn) with MagicNet X gives you convenience and cost reduction.
Samsung LCD Display | 4 + 5

Picture Quality

The Ultimate Visual Journey through Samsung Technologies
Ever since the invention of the display device, people have wanted to see a bigger and better picture. Digital displays allowed for larger screens, but demand for higher picture quality remained unfulfilled. Samsung, not only provides bigger size display, but also provides best picture quality at the same time.
Digital Natural Image engine, DNIeTM
Samsung's dream is to fulfill the demand for lifelike picture quality by creating natural images with vivid color, and optimal detail and contrast. Our proprietary DNIeTM technology, developed through aggressive research & development and 30 years of experience, achieves this dream by taking any signal from a conventional broadcast source and turning it into a stunning picture on any screen.
Motion Optimizer eliminates noise
Motion Optimizer takes visual data and automatically breaks them into signal and noise, eliminating noise and blur without the slightest damage to the original signal. This guarantees a picture of astounding sharpness, whether the scene is still or moving.

Conventional DNIe

Color Optimizer shows natural hues
For each scene, Color Optimizer calculates the saturation of red, green, and blue in the input signal and adjusts it to shades that the human eye accepts as natural. Even white tone enhancement produces more striking results when used with DNIeTM Color Optimizer.
Contrast Enhancer boosts light and shade
Conventional contrast enhancers produce noise boosts and flickers. DNIeTM has solved these problems by developing an epoch-making algorithm called Contrast Enhancer that recognizes over 1 million criteria for applying contrast, and automatically analyzes up to 70,000 local images within a frame - producing a picture rich in contrast, even in the tiniest details.

Conventional

Detail Enhancer sharpens the edges
Detail Enhancer eliminates unnatural effects by automatically analyzing the portion of the signal to be amplified and detecting disturbances to bring the viewer a startlingly sharp and lifelike image.

Highest Contrast Ratio

SyncMaster 320PX / 400PX / 400PXn / 460PX / 460PXn each boast contrast ratio of 1000/1200:1 surpassing the contrast ratio of regular TVs. Theyre capable of delivering a clear image even in brightly-lit settings, ensuring that your customers will be able to get the information they want at a glance.
Conventional SyncMaster 1200:1
Matrix Display for Video Wall

Highest Brightness

Samsung LCD Monitors produce remarkably bright pictures - the industry's highest brightness level at 500 cd/m2. You will not believe your eyes.

SyncMaster 500cd/m2

Samsung LCD Display | 6 + 7

Fast Response Time

The fast response time of 8 ms ensures stable viewing of DVDs and streaming video. Ideal for multimedia-driven applications, gaming, animation or for viewing video over the world wide web.

Conventional 8 ms

Advanced Wide Viewing Angle
Left side, right side or upside-down, whatever your monitor's location, Samsung's solution allows you to see any display clearly due to the wide viewing angle. Your Monitor will always be well placed to enjoy the entertainment no matter what your angle of view is.

Anti-Glare Coating

Special anti-glare coating technology is applied to the screen surface, so the reflection is maximally diffused to ease eyestrain.

Conventional LCD Display

HD Ready
The first thing you'll notice about Samsung HD Ready feature is the exceptional clarity on a wide screen. With Samsung's cutting-edge technologies HD Ready feature realizes razorsharp images as vivid as reality itself.

Conventional HD

Support HDCP
Samsung Monitors are equipped with DVI-D, which allows for the 100% transmission of visual digital signals when connecting to a PC, STB, DVD, or DTV with visual digital signals. The ability to reproduce sources without any signal loss means perfect image recreation that captures every subtle nuance and exquisite detail that digital technology permits. DVI-D guarantees interface with the digital devices of the future.

Low Power

SyncMaster 320PX/400PX/400PXn/400TXn/460PX/460PXn operate with a low power supply, and a Digital Power Management System DPMS) is applied to utilize minimal power (under 1W/5W depending on model) when the unit is in standby mode.

Advanced Panel

The Highest Brightness and Contrast Ratio
A higher brightness ratio brings brilliance to your screen and a higher contrast ratio guarantees an abundance of colors. Typically, brightness and contrast are inversely related. In other words, if brightness goes up, contrast goes down, and vice versa. However, Samsungs LCD Monitor has achieved a flawless balance that no longer has to sacrifice brightness or contrast to achieve the perfect picture. Every scene is always clear and vivid, delivering the details even in bright light. See the Samsung difference.

Lamp Control

Used to adjust Backlight in order to reduce energy consumption. Auto Lamp Control (by MDC Program) - 320PX/400PX/400PXn/400TXn/460PX/460PXn : 450 cd/m2~500 cd/m2

Signal Balance

Used to make up for the weak RGB signal which has been transmitted by a long signal cable.
Samsung LCD Display | 8 + 9
Multi Display Control (MDC)
More control is always good. Especially when its easy. The built-in RS232C interface lets you control up to 10 units as a single display from your PC. Just open the supplied MDC software, list the units to be controlled, and click on the functions to display. Its that simple.

MDC Software Screen Shot

1. Main Icons : Use the main icons to switch to each screen. 2. Select Button : Click Select all or Clear to select or clear all displays. 3. Display Selection : Select a display from Display Selection. 4. Info Grid : Use Grid to view brief information on selected display. 5. Control Tools : Use Control Tools to control displays. 6. Remocon : Allows you to enable or disable the remote control signal receiving function of the display unit. 7. Title : The current title to be controlled is displayed. 8. Comm. Status : Indicates the communication status between the MDC and the display.
Built-In Image Enlarging Processor supports various video wall formats - 2x2, 3x3, 4x4, 5x5, 1x2, 2x1, 1x5, 5x1. To install Video Wall with these formats, you don't need any other Video Controller Device. Also to use video & PC Interface, additional Input Signal Distributor is not necessary.

Innovative Features

Versatile Convenience
A higher brightness ratio brings brilliance to your screen and a higher contrast level. Samsung LCD Monitor supports versatile connectivity for professional convenience. PC and video can be connected and RS-232C loop out function are supported. In addition, 10 units can be connected as one unit and displayed from a PC without additional devices.
Business Display / Department Store

Public Display / Airport

Samsung LCD Display | 10 + 11

Digital Performance

VESA Standard Supported
For video wall convenience, Samsung's New LCD Monitor supports VESA wall mounting standards. 320PX/400PX/400PXn/400TXn/460PX/460PXn have mounting holes at 200 mm x 200 mm. This offers customers various installation solutions including wall mount, vertical mount and ceiling mount.
Professional Connectivity
Samsung LCD Monitor supports extended connectivity PC, Video, RS-232C Loop Out function are supported. If you want to install multi display video wall connected by Video & PC signal, you don't need an additional device like Input Signal Distributor.
2 Way Multi Display Format
In the case of Multi Display video wall, a major issue is how to display naturally without picture distortion. So Samsung's New LCD Monitor supports two types of video wall formats. The first is Full mode which displays the picture regardless of cabinet bezel. The second, Natural Mode, considers bezels depth when displaying picture.

Full Mode

Natural Mode
Vertical Image Capability
SyncMaster 320PX / 400PX / 400PXn / 460PX / 460PXn / 400TXn have a pivot function that freely rotates around 90o degrees, allowing you to easily view a vertical image or text.

Horizontal View

Vertical View

4 Way PIP Function

For your convenience, SyncMaster 320P/400P/400Pn/460P/460Pn/400Txn have added a Picture in Picture display function. This way you can watch a movie, play a game and still carry out business in a third on-screen window. Work & play at the same time!

Small PIP

Large PIP

Double Window 1

Double Window 2

No Noise & Heat

SyncMaster 320P/400P/400Pn/460P/460Pn stand out from other regular monitors, not just for how they look but also for how quiet they are. Because SyncMaster 320P/400P/400Pn/460P/460Pn generate significantly lower heat than comparable units.

Certified Crestron

We established relationships with the key players needed to deliver display solutions. Crestron Electronics, Inc. has been the leader in the systems integration market. We provide seamless display with Crestrons various integrated solutions.

Vertical Input

Landscape idea or portrait idea? Youre not limited with Samsung. Our LCD Monitor can be Mounted either horizontally or vertically.
Samsung LCD Display | 12 + 13

MagicNet X

There are two transmission methods. The first is where the server sends files to the clients after registering to the schedule. In the other, the client searches for the files registered in the library of the server, selects the files to be received, and plays them after receiving them via the network. Each client, by itself, has the capability to access the Internet.
Samsung LCD Monitor supports extended connectivity - PC, Video, RS-232C Loop Out function are supported. If you wantsto install multi display video wall connected by Video & PC signal, you don't need an additional device like Input Signal Distributor.
Server System Requirements OS : Windows 2000, Windows XP

MUSIC PHOTO MOVIE

a RS232C Connect the supplied power cord.
General Spec. (MagicNet Board) OS : WinXPe Storage : 1 GB FDM Connector : USB 2.Ports
e ANT in/FM Ant f AV AUDIO In
- IN : Video and audio inputs for external devices, such as a camcorder or VCR. - OUT : Outputs for external devices.

b DVI/PC IN

- DVI : Connect to the video output jack for device with DVI output. - AUDIO : Connect to the audio output jack for devices with DVI output. - IN : Connect to the video output jack on your PC. - AUDIO : Connect to the audio output jack on your PC. > AUDIO in an audio input jack for PC1 and PC2 Modes.

g AV Out/In (Video)

c COMPONENT AUDIO In
Video (Y/Pb/Pr) and audio (L/R) inputs for component.
h EXT SPEAKER(8 ) Connect external speakers. i AUDIO Out j LAN/USB

d BNC/COMPONENT In

MS-Word, PowerPoint, Excel, Acrobat Viewer, HTML Viewer

HTML, XML, Flash, JAVA

- Connect for RGB (Y/Pb/Pr) HV video signal input from the PC. > PC Mode from this page onward means PC1/PC2 mode using RGB1 (PC1) and RGB2 (PC2) - Video (Y/Pb/Pr) and audio (L/R) inputs for component.

Push Mode

MagicNet transmits media files (photo, audio and movie files) and office files (PowerPoint, Excel, Word, HTML and PDF files: viewer only) existing on a server to clients on an Ethernet network using the server/client architecture.
Client1 Client2 Client3 (1) Scheduling - Digital Contents (2) MDC - Asset Management through LAN (3) Instant Messaging

a b c d

a RS232C OUT/IN (RS232C Serial PORT)
MDC (Multiple Display Control) Program Port
b DVI / PC IN [DVI(HDCP)] (PC Video Connection Terminal)
Using a DVI Cable (DVI-D to DVI-D) - DVI mode (Digital PC)
AV AUDIO IN [L-AUDIO-R] (LCD Display Audio Connection Terminal (Input)) AV OUT [VIDEO] (VIDEO Connection Terminal): AV mode (Output)
c DVI / PC IN [RGB] (PC Video Connection Terminal Using a D-Sub Cable
(15 pin D-Sub) - PC mode (Analog PC)
k AV IN [VIDEO] (VIDEO Connection Terminal (Input)) l AV OUT [S-VIDEO] (S-VIDEO Connection Terminal): S-VIDEO mode (Output)
d DVI / PC IN [PC/DVI/BNC AUDIO IN] (PC/DVI/BNC Audio Connection Terminal (Input))
m AV IN [S-VIDEO] (S-VIDEO Connection Terminal (Input)) n EXT SPEAKER(8 )[- - L - +, - - R - +] (EXT Speaker Connection Terminal) o AUDIO OUT [L-AUDIO-R] (LCD Display Audio Connection Terminal (Output))
AUDIO OUT is the terminal for the PC sound output.

Client4

Client5
e COMPONENT AUDIO IN [L-AUDIOR] (Component Audio Connection Terminal (Input)) f BNC/COMPONENT OUT [R/PR, G/Y, B/PB, H, V] (BNC/Component Connection Terminal (Output))
BNC (Analog PC) Connection: connecting the R, G, B, H, V ports Component Connection: connecting the PR, Y, PB ports

Pull Mode

Several clients can be connected to a server and any file can be transmitted to any client over the network.
Client1 Client2 Client3 Local Device Connectivity through USB 2.0 - Portable Storage Devices (Multimedia Card, Memory Stick, Smart Media, etc.) - Removable Hard Disk - Digital video camera (Only Mass Storage Class)

USB 2.0

p LAN (LAN Connection Terminal)

MS Internet Explorer

g BNC/COMPONENT IN [R/PR, G/Y, B/PB, H, V] (BNC/Component Connection Terminal (Input))
q USB (USB Connection Terminal)
Keyboard / Mouse, Mass Storage Device Compatible.

h Kensington Lock

The Kensington lock is a device used to physically fix the system to something when using it in a public place. (The locking device has to be purchased separately.) To use a locking device, contact the place of purchase.

Client5 PC

Samsung LCD Display | 14 + 15

Accessories

Stand Wall Mount

22.2 18.0

Samsung Plasma Display | 3 + 15

236.0 85.0 85.0 35.0

2-99.2 2-55.2

100.0 240.0

STN-L320PB (320PX)
STN-323TB (400PX/400PXn/400TXn)
WMB-4050PS (400PX/400PXn/460PX/460PXn)

WML4001D (320PX)

Vertical Mount

499.2 2-99.2

21.4 14.5

2-55.2

85.0 85.0 234.0 45.0 45.0
STN-L403TB (460PX/460PXn)

45.0 45.0 45.0 180.0

Speaker

Ceiling Mount

27.5 282.0 330.0
VMN4240D (400PX/400PXn/460PX/460PXn)

482.0 300.0

Components (WMB-4050PS)

100.0 124.1 49.5 78.0

ASSY -HINGE (LEFT): 1 EA
SP-L320PB/S (320PX) WALL BRKT-PLATE: 1 EA ASSY -HINGE (RIGHT): 1 EA PLASTIC: 4 EA SCREW: 11 EA SCREW: 4 EA SCREW: 11 EA
Only use the components and accessories shipped with the product.
Wall Bracket Assembly & Wall Bracket & Wall Bracket Angle Adjustment (WMB-4050PS)

104.0 136.6 80.0

SP-L400PB/S (400PX/400PXn)
Check the installation diagram and mark the drill points on the wall. Use the 5.0 mm bit to drill holes deeper than 35 mm. Fix each anchor in the corresponding hole. Match each of the brackets and hinge holes to the corresponding anchor holes and insert and tighten the 11 A screws.
Remove the 4 screws on the back of the product. Insert screw B into the plastic hanger.
1. Fix the product to the wall bracket. 2. Hold the product at the top in the center and pull it forward (direction of the arrow) to adjust the angle. (See the figure to the right) 3. You can adjust the bracket angle between -2 and 15.

CML 500D (400PX/400PXn/400TXn/460PX/460PXn)
Contact a technician for installing the wall bracket. Samsung Electronics is not responsible for any damages to the product or harm to customers when the installation is done by the customer. This product is intended for installation on cement walls. The product may not be secure when installed on plaster or wood walls.
SP-L460PB/S (460PX/460PXn)
Samsung LCD Display | 16 + 17

Professional LCD Models

320PX 400PX(n)
1000:1 Contrast Ratio (320PX) 1200:1 Contrast Raito (400PX(n)) 450 cd/m2 Brightness (320PX) 500 cd/m2 Brightness (400P(n)) DNIeTM (Digital Natural Image engine) Wide Viewing Angle 178 / 178 High Native Resolution Multimedia Speakers 10 W x 2 ch (option) Matrix Video Wall PIP / PBP / POP MDC (Multi Display Control) through RS232C Powerful Anti Image Retention Safety Lock Support Portrait Display Low Power Consumption Innovative Power Saving System (DPMS) Magicnetwork (Network Model Only) (Black)

460PX(n)

1000:1 Contrast Ratio 500 cd/m2 Brightness Wide Viewing Angle 178 / 178 High Native Resolution Multimedia Speakers 10 W x 2 ch (option) Matrix Video Wall PIP / PBP / POP MDC (Multi Display Control) through RS232C Powerful Anti Image Retention Safety Lock Support Portrait Display Low Power Consumption Innovative Power Saving System (DPMS) Magicnetwork (Network Model Only) (Dark Silver)
982.0 780.0 107.0 58.0 39

400PX / 400PXn / 400TXn

1312.0 1102.0 126.6 61.0 39

460PX / 460PXn

1181.0

658.0 715.0

1181.0 973.0 971.0 920.4(Wall Mount) 118.0 60.5 200.0

400.0(Wall Mount) 67.5

982.0 782.0 780.0 714.0 200.0
1312.0 1104.0 1102.0 600.0(Wall Mount) 200.0

400.0(Wall Mount)

760.2 939.4

607.2 752.0

947.2 1070.4

unit (mm)

Samsung LCD Display | 18 + 19

Specifications

Model Name
Display Diagonal Size Pixel Pitch (mm) Brightness (typ.) Contrast Ratio (typ.) Viewing Angle (H/V) Response Time (ms) (typ.) Frequency Horizontal Frequency (kHz) Vertical Frequency (Hz) Maximum Resolution Color Supported Signal Input Input Video Signal

400PX(n)

40 0.648 x 0.cd/m: / 30-70 50-x 768 16.7 Mil. Analog RGB, BNC, DVI-D, CVBS video S-Video Component Video
46 0.7455 x 0.cd/m: / 30-70 50-x 768 16.7 Mil. Analog RGB, BNC, DVI-D, CVBS Video S-Video Component Video

400Txn

40 0.648 x 0.cd/m: / 30-70 50-x 768 16.7 Mil. Analog RGB, BNC, DVI-D, DVI-D, S-Video Component Video
0.511 x 0.cd/m: / 30-70 50-x 768 16.7 Mil. Analog RGB, BNC, DVI-D, CVBS Video S-Video Component Video
Sync. Type Input Connectors
Separate H/V, Composite, SOG Separate H/V, Composite, SOG Separate H/V, Composite, SOG Separate H/V, Composite, SOG D-Sub, DVI-D, S-Video Video (CVBS) BNC (Component/PC) D-Sub, DVI-D, S-Video Video (CVBS) BNC (Component/PC) DDC 2B 230 W <1 W Black / Dark Silver Black D-Sub, DVI-D, S-Video Video (CVBS) BNC (Component/PC) DDC 2B 280 W <1 W Black / Dark Silver Black D-Sub, DVI-D, S-Video Video (CVBS) BNC (Component/PC) DDC 2B 230 W <1 W Dark Silver Black

Plug & Play-DDC Power On Mode DPMS Mode Cabinet Color Front Cabinet Back OSD-Digital Display DirectorTM Supplied Accessories
DDC 2B 160 W <1 W Black / Dark Silver Black
Kor / Jap / Chi / Fren / Ita / Swe / Ger / Eng / Spa / Por / Rus MDC Program, User Manual, Tablefoot 2 pcs, RCA Adapter 4 pcs, Power Cable, Audio Cable, D-sub Cable MDC Program, User Manual, Tablefoot 2 pcs, RCA Adapter 4 pcs, Power Cable, Audio Cable, D-sub Cable MDC Program, User Manual, Tablefoot 2 pcs, RCA Adapter 4 pcs, Power Cable, Audio Cable, D-sub Cable 1102 x 715 x 293 (option stand) 1102 x 658 x 126.x 824 x 38 SP-L460PB/S WMB-4050PS VMN4240D STN-L403TB 460PXn MDC Program, User Manual, Tablefoot 2 pcs, RCA Adapter 4 pcs, Power Cable, Audio Cable, D-sub Cable 971 x 629.5 x 223 (option stand) 971 x 582 x x 700 x 280 23.5 29.5 SP-L400PS WMB-4050PS VMN4240D STN-L323TB 400TXn

Dimension

Set (W x H x D) mm (with stand) Set (W x H x D) mm (w/o stand) Packing (W x H x D) mm
780 x 529 x 223 (option stand) 971 x 629.5 x 223 (option stand) 780 x 482 x x 600 x 20 SP-L320PB/S WMTLx 582 x x 700 x 280 23.5 29.5 SP-L400PB/S WMB-4050PS VMN4240D STN-L320PB STN-L323TB 400PXn

Weight

Net (kg) Gross (kg)

Optional Accessories

Speaker Wall Mount Vertical Mount Stand Network Model
Specifications mentioned above are subject to change without notice.