Keep any heating devices away from the power cable. A melted coating may lead to electric shock or fire.
Do not install the product in places with poor ventilation, for instance, a bookshelf, closet, etc. Any increase in internal temperature may cause fire.
Set down the monitor carefully. The monitor could be damaged or broken.
Do not place the monitor face down. The CDT surface may be damaged.
Do not use the monitor without the monitor stand. It could break down or cause fire due to bad ventilation. If the monitor must be used without the supplied stand, take steps to insure proper ventilation.
When installing the product, make sure to keep it away from the wall (more than 10 cm/4 inches) for ventilation purposes. Poor ventilation may cause an increase in the internal temperature of the product, resulting in a shortened component life and degraded performance.
Keep the plastic packaging (bag) out of childrens reach. The plastic packaging (bag) may cause suffocation if children play with it.
When cleaning the monitor case or the surface of the CDT, wipe with a slightly
moistened, soft fabric. Do not clean Flat monitor with water. Use a water-diluted mild detergent. (Some detergents contain significant amounts of alcohol-based solvents, which can damage (color change) or crack the monitor case. The antiglare/anti-static surface coating on the CDT may also be affected.) Dilute the detergent (1:10 ratio) with water before using. Do not spray water or detergent directly onto the monitor. This may cause damage, electric shock or fire.
Use the recommended detergent with a smooth cloth. You may prevent the coated CDT from being damaged or the monitor cabinet from being dissolved, cracked or discolored. You may buy a recommended detergent at any Service Center.
If the connector between the plug and the pin is dusty or dirty, clean it properly using a dry cloth. A dirty connector may cause electric shock or fire.
Make sure to unplug the power cord before cleaning the product. Otherwise, this may cause electric shock or fire.
Unplug the power cord from the power outlet and wipe the product using a soft, dry cloth. Do not use any chemicals such as wax, benzene, alcohol, thinners, insecticide, air freshener, lubricant or detergent.
Contact a Service Center or Customer Center for interior cleaning once a year. Keep the product's interior clean. Dust which has accumulated in the interior over an extended period of time may cause malfunction or fire.

Others

Do not remove cover(or back). This may cause electric shock or fire. Refer to a qualified servicing company.
If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized dealer or the Service Center. This may cause electric shock or fire.

Place the product out of childrens reach, as they could damage by hanging onto it. A falling product may cause injury to the person or even fatality.
When not using the product for an extended time period, keep the product unplugged Otherwise, this may cause heat emission from the accumulated dirt or degraded insulation, causing electric shock or fire.
Do not place children's favorite objects (or anything else that may be tempting) on the product. Children may try to climb on the product to retrieve an object. The product could fall, causing physical damage or even death.
Good Postures When Using the Monitor Try to maintain a good posture when using the monitor. Keep your back straight. Keep a distance of about 45 ~ 50 cm between your eyes and the monitor screen. Look at the screen from slightly above it, and have the monitor directly in front of you. Tilt the monitor upwards by 10 ~20 degrees. Adjust the monitor height so that the top of the monitor is slightly below eye level. Adjust the monitor angle so that there is no reflected light on the screen.Try to maintain your arms perpendicular to your armpits. Keep your arms level with the back of your hands. Keep the angle of the elbow perpendicular. Keep the angle of the knees at more than 90 degree. Do not let your feet fall up from the floor. Adjust the arm position so that it is below the heart.
SyncMaster 591S/591SG/591V/594MG/793DF/793MG 793SG/793V/794MG/793S/783DF
Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Contact a local dealer to buy optional items.
Unpacking Monitor and Stand
(Some models include a stand attached.)

Manual

Quick Setup Guide
Warranty Card (Not available in all locations)
User's Guide, Monitor Driver, Natural Color software, MagicTune software

Power Cord Stand

For Multimedia model (Option) Manual

User Guide Cable

Sound Cables(2each) Stand

DC Power Cord

Multimedia Speaker Stand
Menu button [MENU] Adjust buttons [ Enter button [ ] Power button [ ] Power indicator ]

Opens the OSD menu. Also used to exit the OSD menu or return to the previous menu. These buttons allow you to highlight and adjust items in the menu. Used to select the OSD menu. Use this button for turn the monitor on and off. This light glows green during normal operation, and blinks green once as the monitor saves your adjustments.
See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.
(The configuration at the back of the monitor may vary from product to product.)

Power port Signal Cable

Connect the power cord for your monitor to the power port on the back of the monitor. Connect the signal cable to the video port on your computer (video board, video card, or graphics card).
See Connecting the Monitor for further information regarding cable connections.

Bottom

Tilt/Swivel Base
You can separate the base from the monitor.
SyncMaster 592V/794V/788DF Plus

Connecting the Monitor

Setup-For Multimedia model | Multimedia Speaker Stand
Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. Use a connection appropriate for your computer. 2-1. Connecting to a computer Connect the signal cable to the 15-pin, D-sub connector on the back of your computer.
2-2. Connecting to a new Macintosh Connect the monitor to the Macintosh computer using the D-SUB connection cable. Turn on your computer and monitor. If your monitor displays an image, installation is complete.
Setup-For Multimedia model

1. 2. 3.

Turn off your computer and unplug the power cord. Connect the end of the signal cable to your computer's video port(video board, video card or graphics card). Connect one end of the other sound cable to the Mic Input jack on your sound card or computer.Connect the other end of this cable to the Mic By-pass jack on the back of the monitor stand. Plug the DC power cord from the stand into a nearby outlet. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor and the power cord for your computer into a nearby outlet. Turn on your computer and monitor. Turn up or down the On-Off control terminal on the stand of the monitor until it clicks. Execute a sound program, music or sound effect in your computer and then adjust the volume by turning up or down until the sound volume is appropriate. Adjust the treble and bass. Sound distortion may occur when the monitor is placed on top of a mostly hollow cabinet such as your computer. If this occurs, place a pad or magazine beneath the monitor stand. High sound volume may also cause sound distortion; lower the volume.

4. 5. 6. 7. 8. 9. 10.

Multimedia Speaker Stand 1. Mic By-pass Jack To transmit your voice,connect a sound cable from the Mic By-pass jack to the mic in jack on the sound card slot in your computer. Stereo Input Jack Connect a sound cable from the input source(sound card,computer,CD-ROM drive).
DC Power Cord Connect DC power cord to monitor DC 12V output jack. Power Indicator Glows green when the speakers are turned on. On/Off Volume Turns On/Off and adjusts the output volume. Treble Control Use to control high frequencies. Bass Control Use to control low frequencies. Mic Input Jack To transmit your voice,connect a microphone to this jack. Headphone Jack To listen in privacy,connect headphones here. Detachable Stand Top

4. 5. 6. 7. 8.

9. 10.

Base Installation

Tilt/Swivel Base | Attaching and Removing the Base Tilt/Swivel Base With the built-in pedestal, you can tilt and/or swivel the monitor for the most comfortable viewing angle.

The base is detachable.

Attaching and Removing the Base If your monitor was supplied with the base detached, attach the base as follows.
Remove the twist-tie before attaching the base to the monitor.
Attaching the Base Place the monitor upside-down on a flat work surface. Align the tabs on the base with the corresponding slots on the bottom of the monitor. Press the base onto the monitor until the tabs are fully engaged in the slots. Push the base toward the front of the monitor until the release latch clicks into the locked position. * Do not bend the snap. Removing the Base 5. Squeeze and pull up on the release latch on the base. 6. Push the base toward the back of the monitor and lift up to remove the base. The base will align with the monitor slots in only one position. 1. 2. 3. 4.
Installing the Monitor Driver(Automatic)
When prompted by the operating system for the monitor driver, insert the CD-ROM
included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown here. Internet web site : http://www.samsung.com/ (Worldwide) http://www.samsung.com/monitor (U.S.A) http://www.sec.co.kr/monitor (Korea) http://www.samsungmonitor.com.cn/ (China)
1. Insert the CD into the CD-ROM drive. 2. Click "Windows" 3. Choose your monitor model in the model list, then click the "OK".
4. If you can see following message window, then click the "Continue Anyway" button. Then click "OK". (Microsoft Windows XP/2000 Operating System)
This monitor driver is under certified MS logo and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/. 5. Monitor driver installation is completed.

5. 6. 7. 8. 9. 10.

Microsoft Windows NT Operating System 1. Click Start, Settings, Control Panel, and then double-click Display icon. 2. In Display Registration Information window, click Settings Tab and then click All Display Modes. 3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and then click OK. 4. Click Apply button if you see the screen working normally after clicking Test. If the screen is not normal, change to a different mode (lower mode of resolution, colors or frequency). If there is no Mode at All Display Modes, select the level of resolution and vertical frequency by referring to the Preset Timing Modes in the user guide. Linux Operating System To execute X-Window, you need to make the X86Config file, which is a type of system setting file. Press Enter at the first and the second screen after executing the X86Config file. The third screen is for setting your mouse. Set a mouse for your computer. The next screen is for selecting a keyboard. Set a Keyboard for your computer. The next screen is for setting your monitor. First of all, set a horizontal frequency for your monitor. (You can enter the frequency directly.) 8. Set a vertical frequency for your monitor. (You can enter the frequency directly.) 9. Enter the model name of your monitor. This information will not affect the actual execution of X-Window. 10. You have finished setting up your monitor. Execute X-Window after setting other requested hardware. 1. 2. 3. 4. 5. 6. 7.
Natural Color Natural Color Software Program
One of the recent problems in using a computer is that the color of the images printed out by a printer or other images scanned by a scanner or a digital camera are not the same as those shown on the monitor. The Natural Color S/W is the very solution for this problem. It is a color administration system developed by Samsung Electronics in association with Korea Electronics & Telecommunications Research Institute (ETRI). This is only available for Samsung monitors and ensures that the color of the images on the

MagicTune execution icon may not appear depending on specification of computer system or monitor. If that happens, press F5 Key.

Installation Problems

The installation of MagicTune can be affected by such factors as the video card, motherboard and the network environment.

System Requirements

OS Windows Windows Windows Windows 2000 XP Home Edition XP Professional Vista
It is recommended using MagicTune in Windows 2000 or later.
Hardware 32 MB Memory above 60 MB Hard disk space above
* For more information, visit the MagicTune website.

Uninstall

The MagicTune program can be removed only by using the "Add or Remove Programs" option of the Windows Control Panel. Perform the following steps remove MagicTune. 1. 2. 3. 4. 5. 6. Go to [Task Tray] ' [Start] ' [Settings] and select [Control Panel] in the menu. If the program runs on Windows XP, go to [Control Panel] in the [Start] menu. Click the "Add or Remove Programs" icon in Control Panel. In the "Add or Remove Programs" screen, scroll down to find "MagicTune." Click on it to highlight it. Click the "Change/Remove" button to remove the program. Click "Yes" to begin the uninstall process. Wait until the "Uninstall Complete" dialog box appears.
Visit the MagicTune website for technical support for MagicTune , FAQs (questions and answers) and software upgrades.

Check List

Before calling for service, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer.
Symptom No images on the screen. I cannot turn on the monitor.
Check List Is the power cord connected properly? Can you see " the screen? " on
Solutions Check the power cord connection and supply. Check the signal cable connection. If the initial screen (the login screen) appears, boot the computer in the applicable mode (the safe mode for Windows ME/XP/2000) and then change the frequency of the video card. (Refer to the Preset Timing Modes) Note: If the initial screen (the login screen) does not appear, contact a service center or your dealer.

The screen can be unbalanced due to the cycle of the video card signals. Readjust Position by referring to the OSD. The screen is out of focus or OSD cannot be adjusted. The screen is partially distorted. Have you adjusted the resolution or frequency on the monitor? Are there any magnetic products such as an adapter, speaker or a high voltage wire near the monitor? Is the frequency properly adjusted when checking the Display Timing on the menu? Adjust the resolution and frequency of the video card. (Refer to the Preset Timing Modes). Enter the OSD and perform a "Degauss". Keep the monitor away from any magnetic products. Adjust the frequency properly by referring to the video card manual and the Preset Timing Modes. (The maximum frequency per resolution may differ from product to product.) There are only 16 colors shown on the screen. The screen colors have changed after changing the video card. There is a message that reads "Unrecognized monitor, Plug & Play (VESA DDC) monitor found". Windows ME/2000/XP: Have the Windows colors been set properly? Set the colors properly at the Control Panel Display Settings. Has the video card been set properly? Have you installed the monitor driver? See the video card manual to see if the Plug & Play (VESA DDC) function can be supported. MagicTune feature is found only on PC (VGA) with Window OS that supports Plug and Play. Set the video card by referring to the video card manual. Install the monitor driver according to the Driver Installation Instructions. Install the monitor driver according to the Driver Installation Instructions.
LED is blinking but no images on the screen.
Check when MagicTune does not function properly.
* To check whether your PC is available for MagicTune feature, follow the steps below (When Windows is XP);
Control Panel Performance and Maintenance System Hardware Device Manager Monitors After deleting Plug and Play monitor, find 'Plug and Play monitor' by searching new Hardware. MagicTune is an additional software for the monitor. Some graphic cards may not support your monitor. When you have a problem with the graphic card, visit our website to check the compatible graphic card list provided. http://www.samsung.com/monitor/magictune MagicTune doesn't work properly. Have you changed your PC or video graphic card? Did you install the program? Download the latest program. The program can be downloaded http://www.samsung.com/monitor/magictune. Reboot the computer after installing the program for the first time. If a copy of the program is already installed, remove it, reboot the computer, and then install the program again. You need to reboot the computer for it to operate normally after installing or removing the program.
Visit the MagicTune website and download the installation software for MagicTune MAC.

Check the following items if there is trouble with the monitor. 1. Check if the power cord and the video cables are properly connected to the computer. 2. Check if the computer beeps more than 3 times when booting. (If it does, request an after-service for the main board of the computer.) 3. If you installed a new video card or if you assembled the PC, check if the installed adapter (video) driver and the monitor driver. 4. Check if the scanning ratio of the video screen is set at 50Hz ~ 160Hz. (Do not exceed 65Hz when using the maximum resolution.) 5. If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode, remove the Display Adapter at the "Control PanelSystemDevice Administrator" and then reboot the computer to reinstall the adapter (video) driver.
If problems repeatedly occur, contact an authorized service center.

Q&A

Question How can I change the frequency?
Answer Frequency can be changed by reconfiguring the video card. Note that video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details.) Windows ME/XP/2000 : Set the resolution at the Control PanelDisplaySettings. * Contact the video card manufacturer for details.
How can I adjust the resolution?
How can I set the Power Saving function?
Windows ME/XP/2000 : Set the function at BIOS-SETUP of the computer or the screen saver. (Refer to Windows/Computer Manual).
The monitor makes a sound when it is turned on. How can I clean the outer case/Picture tube?
This is normal as some sound may be generated when the metal case and the electromagnet, which are installed to block any electromagnetic waves, interact with each other. Disconnect the power cord and then clean the monitor with a soft cloth, using either a cleaning solution or plain water. Do not leave any remains of the detergent nor scratch the case. Do not allow any water to go inside the monitor.
Self-Test Feature Check Self-Test Feature Check | Warning Messages | Environment | Useful Tips Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly. Self-Test Feature Check 1. Turn off both your computer and the monitor. 2. Unplug the video cable from the back of the computer. 3. Turn on the monitor. If the monitor is functioning properly, you will see a box in the illustration below.

Weight 11.0 kg / 24.3 lbs Environmental considerations Operating Storage Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings. Note: Design and specifications are subject to change without prior notice. Class B Equipment (Information Communication equipment for residential use) This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.) Temperature 32F ~ 104F(0C ~ 40C) Humidity 10% ~ 80%, non-condensing Temperature -4F ~113F (-20C ~ 45C) Humidity 5% ~ 95%, non-condensing
PowerSaver This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPMS compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature. State Power Indicator Power Consumption Normal Operation Green Less than 50 W (at the windows pattern) Power-off mode Green, Blinking Less than 1 W
Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Horizontal Frequency (kHz) 37.500 43.300 53.700 Vertical Frequency (Hz) 75.000 85.000 85.100
Display Mode VESA, 640 x 480 VESA, 640 x 480 VESA, 800 x 600
Pixel Clock (MHz) 31.500 36.000 56.250
Sync Polarity (H/V) -/-/+/+

Horizontal Frequency

The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz Vertical Frequency Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz
General General Model Name Picture Tube Type Deflection angle Dot Pitch Resolution Optimum resolution Maximum resolution Active Display Horizontal Vertical Synchronization Horizontal Vertical Input Signal Definition Video Signal Sync Signal Display Color Unlimited Maximum Pixel Clock 65 MHz Power Supply AC 100 - 240 V~ (+/- 10 %), 50/60 Hz Dimensions (WxDxH) 361 x 376 x 346 mm / 14.2 x 14.8 x 13.6 inch (After installation of Stand) RGB, Analog 0.7 Vp-p Positive at 75 Separate H/V sync, TTL level, positive or negative 30 ~ 55 kHz 50 ~ 120 Hz mm mm 800 x 600 @ 85 Hz 1024 x 768 @ 70 Hz 15" (38 cm) FST (35 cm viewable) 90 0.24 mm (Horizontal) SyncMaster 592V

PowerSaver This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPMS compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature. State Power Indicator Power Consumption Normal Operation Green Less than 55 W (at the windows pattern) Power-off mode Green, Blinking Less than 1 W
Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Horizontal Frequency (kHz) 37.500 53.700 68.700 Vertical Frequency (Hz) 75.000 85.100 85.000
Display Mode VESA, 640 x 480 VESA, 800 x 600 VESA, 1024 x 768
Pixel Clock (MHz) 31.500 56.250 94.500
Sync Polarity (H/V) -/+/+ +/+
General General Model Name Picture Tube Type Deflection angle Dot Pitch Resolution Optimum resolution Maximum resolution Active Display Horizontal Vertical Synchronization Horizontal Vertical Input Signal Definition Video Signal Sync Signal Display Color Unlimited Maximum Pixel Clock 110 MHz Power Supply AC 100 - 240 V~ (+/- 10 %), 50/60 Hz Dimensions (WxDxH) 401 x 410 x 378 mm / 15.8 x 16.1 x 14.9 inch (After installation of Stand) RGB, Analog 0.7 Vp-p Positive at 75 Separate H/V sync, TTL level, positive or negative 30 ~ 70 kHz 50 ~ 160 Hz mm mm 1024 x 768 @ 85 Hz 1280 x 1024 @ 65 Hz 17" (43 cm) FSE (40.6 cm viewable) 90 0.23 mm (Horizontal) SyncMaster 794V
Weight 12.8 kg / 28.2 lbs Environmental considerations Operating Storage Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings. Note: Design and specifications are subject to change without prior notice. Class B Equipment (Information Communication equipment for residential use) This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.) Temperature 32F ~ 104F(0C ~ 40C) Humidity 10% ~ 80%, non-condensing Temperature -4F ~113F (-20C ~ 45C) Humidity 5% ~ 95%, non-condensing

General General Model Name Picture Tube Type Deflection angle Dot Pitch Resolution Optimum resolution Maximum resolution Active Display Horizontal Vertical Synchronization Horizontal Vertical Input Signal Definition Video Signal Sync Signal Display Color Unlimited Maximum Pixel Clock 110 MHz Power Supply AC 100 - 240 V~ (+/- 10 %), 50/60 Hz Dimensions (WxDxH) 401 x 410 x 378 mm / 15.8 x 16.1 x 14.9 inch (After installation of Stand) RGB, Analog 0.7 Vp-p Positive at 75 Separate H/V sync, TTL level, positive or negative 30 ~ 70 kHz 50 ~ 160 Hz mm mm 1024 x 768 @ 85 Hz 1280 x 1024 @ 65 Hz 17" (43 cm) Flat (40.6 cm viewable) 90 0.20 mm (Horizontal) SyncMaster 783DF/793DF/793MG/788DF Plus
Weight 14.3 kg / 31.5 lbs Environmental considerations Operating Storage Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings. Note: Design and specifications are subject to change without prior notice. Class B Equipment (Information Communication equipment for residential use) This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.) Temperature 32F ~ 104F(0C ~ 40C) Humidity 10% ~ 80%, non-condensing Temperature -4F ~113F (-20C ~ 45C) Humidity 5% ~ 95%, non-condensing
SyncMaster 591V/591S/592V/793V/794V/793DF/793S/783DF
Contact SAMSUNG WORLDWIDE If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center.
North America U.S.A CANADA MEXICO 1-800-SAMSUNG (7267864) 1-800-SAMSUNG (7267864) 01-800-SAMSUNG (7267864) http://www.samsung.com http://www.samsung.com/ca http://www.samsung.com/mx
Latin America ARGENTINE BRAZIL CHILE COLOMBIA COSTA RICA ECUADOR EL SALVADOR GUATEMALA JAMAICA PANAMA PUERTO RICO REP. DOMINICA TRINIDAD & TOBAGO VENEZUELA 0800-333-3733 4004-0000 800-726-7864 (SAMSUNG) 01-8000112112 0-800-507-7267 1-800-10-7267 800-6225 1-800-299-0013 1-800-234-7267 800-7267 1-800-682-3180 1-800-751-2676 1-800-7267-864 0-800-100-5303 http://www.samsung.com/ar http://www.samsung.com/br http://www.samsung.com/cl http://www.samsung.com.co http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin

Correct Disposal of This Product (Waste Electrical & Electronic Equipment) - Europe only
(Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.

5. Monitor driver installation is completed. Windows XP/2000
1. Insert CD into the CD-ROM driver. 2. Click "Windows XP/2000 Driver". 3. Choose your monitor model in the model list, then click the "OK" button.
5. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button.
This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Samsung Monitor Homepage http://www.samsung-monitor.com/. 6. Monitor driver installation is completed.

Windows XP

| Windows 2000 | Windows Me | Windows NT | Linux
Microsoft Windows XP Operating System
1. Insert CD into the CD-ROM driver. 2. Click "Start" > "Control Panel" then click the "Appearance and Themes" Icon.
3. Click "Display" icon and choose the "Settings" tab then click "Advanced.".
4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab.
5. Click "Update Driver." and select "Install from a list or." then click "Next" button.
6. Select "Don't search ,I will." then click "Next" and then click "Have disk".
7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button.
8. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button.
This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Samsung Monitor Homepage http://www.samsung-monitor.com/. 9. Click the "Close" button then click "OK" button continually.
10. Monitor driver installation is completed.
Microsoft Windows 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose "OK" button on the "Insert disk" window. 2. Click the "Browse" button on the "File Needed" window. 3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button. How to install 1. 2. 3. 4. Click "Start" , "Setting" , "Control Panel". Double click the "Display" Icon. Choose the "Settings" tab and then click "Advanced.". Choose "Monitor". Case1: If the "Properties" button is inactive, it means your monitor is properly configured. Please stop installation Case2: If the "Properties" button is active, click the "Properties" button then follow next steps continually. Click "Driver" and then click on "Update Driver." then click on the "Next" button. Choose "Display a list of the known drivers for this device so that I can choose a specific driver" then click "Next" and then click "Have disk". Click the "Browse" button then choose A:(D:\Driver). Click the "Open" button, then click "OK" button. Choose your monitor model and click the "Next" button then click "Next" button. Click the "Finish" button then the "Close" button. If you can see the "Digital Signature Not Found" window then click the "Yes"button. And click the "Finish" button then the "Close" button.

Tilt/Swivel Base

| Attaching and Removing the Base
Connecting Your Monitor Installing the Monitor Driver
With the built-in pedestal, you can tilt and/or swivel the monitor for the most comfortable viewing angle.
Note: The base is detachable.
If your monitor was supplied with the base detached, attach the base as follows.
Remove the twist-tie before attaching the base to the monitor.
Attaching the Base 1. 2. 3. 4. Place the monitor upside-down on a flat work surface. Align the tabs on the base with the corresponding slots on the bottom of the monitor. Press the base onto the monitor until the tabs are fully engaged in the slots. Push the base toward the front of the monitor until the release latch clicks into the locked position. * Do not bend the snap.
Removing the Base 5. Squeeze and pull up on the release latch on the base. 6. Push the base toward the back of the monitor and lift up to remove the base. Note: The base will align with the monitor slots in only one position.

SyncMaster 591S/591V

User con trol butt ons Direct-Access Fe ature s OSD Fu nction s Adju sting Yo ur Monitor MagicTune
User co n tro l bu tto ns

1. 2. 3.

Op ens the OSD menu. Also use to exit t he OSD m enu or re turn to the p revious menu. These b uttons allow you t o highlig ht and a dju st item s in t he men u. Use to select the OSD menu.
Direct -Acces s Fe atu res

| Brightness |

| Contrast |

OSD Fu n ctio ns

osd Adju st t he Bright ness. Adju st t he Co ntrast.

Descrip tion

Play / Stop
A "Mo ir" pattern can app ear on your screen, looking like a series of concent ric circles or arcs. To eliminat e this pattern, use the horizonta l m oire ad justme nts. A "Mo ir" pattern can app ear on your screen, looking like a series of concent ric circles or arcs. To eliminat e this pattern, use the vertical moire a dju stm ents. The Degau ss fea ture will remove color im purities caused by mag netic fie lds. Use the recall f eature to reset these m onitor set ting s t o their o riginal le ve ls: Positio n, Size , Pincushion, T ra pezoid, Parallelogram, Pinba lan ce, Rotat ion , H-Moire,a nd V-Moire. Note: If yo u have selected "Yes", all settings liste d above w ill be reset. All other settings will remain the sam e.

Descrip tion Color temperature is a measure of th e 'w arm th' o f the imag e colo rs. (6500K / 9 300K) Use to ad just th e monitor color setting. (Re d) Use to ad just th e monitor color setting. (Gre en) Use to ad just th e monitor color setting. (Blue) When you a dju st t he Bright ness and C ontra st after sR GB mode is selected, sRGB m ode exits.
Descrip tion Follow th ese in structions to chang e the ho rizontal positio n of the monitor's entire disp lay. Follow th ese in structions to chang e the vetical position of the m onitor's entire display. Follow th ese in structions to chang e the ho rizontal size of the mo nit or's e ntire display. Follow th ese in structions to chang e the vertical size of the m onitor's entire display. Adju st t he pincushio n setting w hen the sides of the displa y are b owed in or bo wed o ut. Adju st t he pinbalance setting when the sid es of the d isplay are bow ed tow ard s th e left or right. Adju st t he trapezoid setting wh en the top or botto m of the disp lay is too large or sm all. Adju st t he parallelogram sett ing when the display is leaning left or rig ht.
You can see th e fre quency (u ser control mode) used by th e user, the polarit y o f the op erationa l signals, the d efault frequ ency (defa ult mode) set wh en you bu y t he mon itor and the resolu tio n le ve l. Note : The se screens do n ot allo w any chan ges to the set ting s, they are for inf orma tio n only.
SyncMaster 793S/793V/783DF/793DF/795DF
Descrip tion Follow th ese in structions to chang e the ho rizontal positio n of the monitor's entire disp lay. Follow th ese in structions to chang e the vetical position of the m onitor's entire display. Follow th ese in structions to chang e the ho rizontal size of the mo nit or's e ntire display. Follow th ese in structions to chang e the vertical size of the m onitor's entire display. Adju st t he pincushio n setting w hen the sides of the displa y are b owed in or bo wed o ut. Adju st t he pinbalance setting when the sid es of the d isplay are bow ed tow ard s th e left or right. Adju st t he trapezoid setting wh en the top or botto m of the disp lay is too large or sm all. Adju st t he parallelogram sett ing when the display is leaning left or rig ht. Adju st t he ro tation setting w hen th e entire display is tilted left or rig ht.

SyncMaster 797DF

Descrip tion Color temperature is a measure of th e 'w arm th' o f the imag e colo rs. T he availa ble ran ge is betw een to 9300K. Use to ad just th e monitor color setting. (Re d) Use to ad just th e monitor color setting. (Gre en) Use to ad just th e monitor color setting. (Blue) When you a dju st t he Bright ness and C ontra st after sR GB mode is selected, sRGB m ode exits.
Descrip tion Follow th ese in structions to chang e the ho rizontal positio n of the monitor's entire disp lay. Follow th ese in structions to chang e the vetical position of the m onitor's entire display. Follow th ese in structions to chang e the ho rizontal size of the mo nit or's e ntire display. Follow th ese in structions to chang e the vertical size of th e monitor's entire disp la y. Adju st t he pincushio n setting w hen the sides of the displa y are b owed in or bo wed o ut. Adju st t he pinbalance setting when the sid es of the d isplay are bow ed tow ard s th e left or right. Adju st t he trapezoid setting wh en the top or botto m of the disp lay is too large or sm all. Adju st t he parallelogram sett ing when the display is leaning left or rig ht. Adju st t he ro tation setting w hen th e entire display is tilted left or rig ht.
Adju st t he sid e pin corne r correction w hen th e top or bott om of th e displa y is too large or sma ll.
OSD Adju st t he Bright ness. Adju st t he Co ntrast.
A "Mo ir" pattern can app ear on your screen, looking like a series of concent ric circles or arcs. To eliminat e this pattern, use the horizonta l m oire ad justme nts. A "Mo ir" pattern can app ear on your screen, looking like a series of concent ric circles or arcs. To eliminat e this pattern, use the vertical moire a dju stm ents. The Degau ss fea ture will remove color im purities caused by mag netic fie lds. Use the recall f eature to reset these m onitor set ting s t o their o riginal le ve ls: Positio n, Size , Pincushion, T ra pezoid, Parallelogram, Pinba lan ce, Rotat ion , H-Moire,a nd V-Moire. Note : If yo u have selected "Yes", all settings liste d above w ill be reset. All other settings will remain the sam e. (Optio n) Use this menu to choose bet ween the signal source conn ected to t he BNC connector input and the signa l source connected to the D -SUB connector input.

MagicTune may not work in case monitor is replaced or driver of graphic card is updated while MagicTune is operating. If so, please restart the system.
Check when MagicTune does not function properly. * MagicTune feature is found only on PC (VGA) with Window OS that supports Plug and Play. * To check whether your PC is available for MagicTune feature, follow the steps below (When Windows is XP); Control Panel -> Performance and Maintenance -> System -> Hardware -> Device Manager -> Monitors -> After deleting Plug and Play monitor, find 'Plug and Play monitor' by searching new Hardware.
Visit the MagicTune website for technical support for MagicTune, FAQs (questions and answers) and software upgrades.
Before calling for service, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call, the phone number on the Information section or contact your dealer. Check List
Q&A Self-Test Feature Check

Symptom

No images on the screen. I cannot turn on the monitor.

Check List

Is the power cord connected properly? Can you see " screen? " on the

Solutions

Check the power cord connection and supply. Check the signal cable connection.
If the power is on, reboot the computer to see the initial screen(the login screen), which can be seen.
If the initial screen (the login screen) appears, boot the computer in the applicable mode (the safe mode for Windows ME/XP/2000) and then change the frequency of the video card. (Refer to the Preset Timing Modes) Note: If the initial screen (the login screen) does not appear, contact a service center or your dealer.
Can you see " screen?

" on the

You can see this message when the signal from the video card exceeds the maximum resolution and frequency that the monitor can handle properly. Adjust the maximum resolution and frequency that the monitor can handle properly.
There is no image on the screen. Is the power indicator on the monitor blinking at 1 second intervals?
The monitor is in PowerSaver mode. Press any key on the keyboard or move the mouse to activate the monitor and restore the image on the screen. The signal from the video card exceeds the maximum resolution and frequency of the monitor.
The image on the screen is shaking.
Check the monitor configuration to see if it is in Interlace Mode. (Interlace Mode: Vertical frequency 43Hz, 87Hz(i), etc) Are there any magnetic products such as a power adapter, speaker or a high voltage wire near by? Is the voltage stable?

Move the monitor away from anything that can create a strong magnetic field.
The screen image can appear to shake or vibrate at a particular time of day due to low supply voltage.
The screen image can also appear to shake or vibrate if there is a problem with the video card or the computer's main board. The screen shows strange colors or just black and white. Is the screen displaying only one color as if looking at the screen through a cellophane Check the signal cable connection. Make sure the video card is fully
paper? Have the screen colors become strange after running a program or due to a crash between applications? Has the video card been set properly? The screen suddenly has become unbalanced. Have you changed the video card or the driver? Have you adjusted the resolution or frequency on the monitor?
inserted in it's slot. Reboot the computer.
Set the video card by referring to the video card manual. Adjust screen image position and size using the OSD. Adjust the resolution and frequency at the video card. (Refer to the Preset Timing Modes).
The screen can be unbalanced due to the cycle of the video card signals. Readjust Position by referring to the OSD. The screen is out of focus or OSD cannot be adjusted. The screen is partially distorted. Have you adjusted the resolution or frequency on the monitor? Are there any magnetic products such as an adapter, speaker or a high voltage wire near the monitor? Adjust the resolution and frequency of the video card. (Refer to the Preset Timing Modes). Enter the OSD and perform a "Degauss". Keep the monitor away from any magnetic products. Adjust the frequency properly by referring to the video card manual and the Preset Timing Modes. (The maximum frequency per resolution may differ from product to product.) There are only 16 colors shown on the screen. The screen colors have changed after changing the video card. There is a message that reads "Unrecognized monitor, Plug & Play (VESA DDC) monitor found". Have the Windows colors been set properly? For Windows ME/XP/2000: Set the colors properly at the Control Panel, Display, Settings. Set the video card by referring to the video card manual. Install the monitor driver according to the Driver Installation Instructions. Install the monitor driver according to the Driver Installation Instructions.
LED is blinking but no images on the screen.
Is the frequency properly adjusted when checking the Display Timing on the menu?

SyncMaster 591S/793S/591V/793V/783DF/793DF /795DF/797DF/793MB/795MB
This box appears during normal operation if the video cable becomes disconnected or damaged. 4. Turn off your monitor and reconnect the video cable; then turn on both your computer and the monitor. If your monitor screen remains blank after using the previous procedure, check your video controller and computer system; your monitor is functioning properly.
If there is something wrong with the input signal, a message appears on the screen or the screen goes blank although the power indicator LED is still on. The message may indicate that the monitor is out of scan range or that you need to check the signal cable.
The location and the position of the monitor may influence the quality and other features of the monitor. 1. If there are any sub woofer speakers near the monitor, unplug and relocate the woofer to another room. 2. Remove all electronic devices such as radios, fans, clocks and telephones that are within 3 feet (one meter) of the monitor. 3. Degauss the monitor if any devices were removed from the area.
A monitor recreates visual signals received from the computer. Therefore, if there is trouble with the computer or the video card, this can cause the monitor to become blank, have poor coloring, noise, Sync. Out of Range, etc. In this case, first check the source of the problem, and then contact a service center or your dealer. Judging the monitor's working condition If there is no image on the screen or a "Sync. Out of Range" message comes up, disconnect the cable from the computer while the monitor is still powered on. If there is a message coming up on the screen or if the screen goes white, this means the monitor is in working condition. In this case, check the computer for trouble.
General Model Name General
PowerSaver Preset Timing Modes
Picture Tube Type Deflection angle Dot Pitch Screen type 15" (38cm) Full square type (35cm viewable) 90 0.24mm (Horizontal) Aluminized tri-color phosphor dot trio with black matrix. Anti-doming invar shadow mask. Multi-layer coated with anti-static/Glare.
Maximum Resolution 1024 x 768(NI) Active Display Horizontal Vertical Synchronization Horizontal Vertical Input Signal Definition Video Signal Sync Signal Display Color Unlimited Maximum Pixel Clock 65 MHz Power Supply 90 ~ 264VAC rms, 60/50 Hz 3Hz Power Consumption Less than 70W Dimensions (WxDxH) 361 x 379.2 x 347 mm (After installation of Stand) Weight 11.0 kg Environmental considerations Operating Temperature 32F ~ 104F(0C ~ 40C) Humidity 10% ~ 80%, non-condensing Storage Temperature -4F ~113F (-20C ~ 45C) Humidity 5% ~ 95%, non-condensing Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will proceed automatically, unless the user wishes to select alternate settings. Note: Design and specifications are subject to change without prior notice. RGB, Analog 0.7 Vpp positive at 75 ohms Separate H/V sync, TTL level, positive or negative 30 - 55 kHz 50 ~ 120 Hz mm mm

Maximum Resolution 1600 x 1200@76Hz Active Display Horizontal Vertical Synchronization Horizontal Vertical Input Signal Definition Video Signal Sync Signal Display Color Unlimited Maximum Pixel Clock 250 MHz Power Supply 90 ~ 264VAC rms, 60/50 Hz 3Hz Power Consumption Less than 90W Dimensions (WxDxH) 401 x 410 x 378mm (After installation of Stand) Weight 14.3kg Environmental considerations Operating Temperature 32F ~ 104F(0C ~ 40C) Humidity 10% ~ 80%, non-condensing Storage Temperature -4F ~113F (-20C ~ 45C) Humidity 5% ~ 95%, non-condensing Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will proceed automatically, unless the user wishes to select alternate settings. Note: Design and specifications are subject to change without prior notice. RGB, Analog 0.7 Vpp positive at 75 ohms Separate H/V sync, TTL level, positive or negative 30 ~ 96 kHz 50 ~ 160 Hz mm mm
Picture Tube Type Deflection angle Dot Pitch Screen type 19"(48cm) DynaFlat (45.8cm viewable) 90 0.20mm (Horizontal) Aluminized tri-color phosphor dot trio with black matrix. Anti-doming invar shadow mask. Multi-layer coated with anti-static.
Maximum Resolution 1600 X 1200@ 76Hz Active Display Horizontal Vertical Synchronization Horizontal Vertical Input Signal Definition Video Signal Sync Signal Display Color Unlimited Maximum Pixel Clock 250 MHz Power Supply 90 ~ 264VAC rms, 60/50 Hz 3Hz Power Consumption Less than 110W Dimensions (WxDxH) 445 x 457.5 x 416mm (After installation of Stand) Weight 18.2 kg Environmental considerations Operating Temperature 32F ~ 104F(0C ~ 40C) Humidity 10% ~ 80%, non-condensing Storage Temperature -4F ~113F (-20C ~ 45C) Humidity 5% ~ 95%, non-condensing Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will proceed automatically, unless the user wishes to select alternate settings. Note: Design and specifications are subject to change without prior notice. RGB, Analog 0.7 Vpp positive at 75 ohms Separate H/V sync, TTL level, positive or negative 30 ~ 96 kHz 50 ~ 160 Hz mm mm

PowerSaver

Preset Timing Modes
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you move the computer's mouse or press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPMS compliant video card installed in your computer. Use a software utility installed on your computer to set up this feature. State Power Indicator Power Consumption Normal Operation Green Less than 70W Power-off Mode EPA/ENERGY 2000 Green, Blinking Less than 2W
This monitor is EPA ENERGY STAR compliant and ENERGY2000 compliant when used with a computer equipped with VESA DPMS functionality. As an ENERGY STAR Partner, SAMSUNG has determined that this product meets the ENERGY STAR guidelines for energy efficiency.
SyncMaster 793S/793V/783DF/795DF 793DF/797DF/793MB/795MB
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you move the computer's mouse or press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPMS compliant video card installed in your computer. Use a software utility installed on your computer to set up this feature. State Power Indicator Power Consumption Normal Operation Green Less than 90W Power-off Mode EPA/ENERGY 2000 Green, Blinking Less than 2W
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you move the computer's mouse or press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPMS compliant video card installed in your computer. Use a software utility installed on your computer to set up this feature. State Power Indicator Power Consumption Normal Operation Green Less than 110W Power-off Mode EPA/ENERGY 2000 Green, Blinking Less than 2W
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows.

General PowerSaver

Table 1. Preset Timing Modes Display Mode VESA, 640 x 480 VESA, 640 x 480 VESA, 800 x 600 Horizontal Frequency (kHz) 37.500 43.269 53.674 Vertical Frequency (Hz) 85.008 75.000 85.061 Pixel Clock (MHz) 36.000 31.500 56.250 Sync Polarity (H/V) -/-/+/+
Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle and the inverse number of the Horizontal Cycle is called Horizontal Frequency. Unit: kHz Vertical Frequency Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called Vertical Frequency or Refresh Rate. Unit: Hz
SyncMaster 793S/793V/783DF/793DF793MB
Table 1. Preset Timing Modes Display Mode VESA, 640 x 480 VESA, 800 x 600 VESA, 1024 x 768 VESA, 1152 x 864 Horizontal Frequency (kHz) 37.500 53.674 68.677 67.500 Vertical Frequency (Hz) 75.000 85.061 84.997 75.000 Pixel Clock (MHz) 31.500 56.250 94.500 108.000 Sync Polarity (H/V) -/+/+ +/+ +/+
Table 1. Preset Timing Modes Display Mode VESA, 640 x 480 VESA, 1024 x 768 VESA, 1280 x 1024 Horizontal Frequency (kHz) 37.500 68.677 79.976 Vertical Frequency (Hz) 75.000 84.997 75.025 Pixel Clock (MHz) 31.500 94.500 135.00 Sync Polarity (H/V) -/+/+ +/+

SyncMaster 797DF/997DF

Table 1. Preset Timing Modes Display Mode VESA, 640 x 480 VESA, 1024 x 768 VESA, 1280 x 1024 Horizontal Frequency (kHz) 37.500 68.677 91.146 Vertical Frequency (Hz) 75.000 84.997 85.024 Pixel Clock (MHz) 31.500 94.500 157.50 Sync Polarity (H/V) -/+/+ +/+

Service

Terms Regulatory Natural Color Authority
AUSTRALIA : Samsung Electronics Australia Pty Ltd. Customer Response Centre 7 Parkview Drive, Homebush Bay NSW 2127 Tel : 603 http://www.samsung.com.au/ BRAZIL : Samsung Eletronica da Amazonia Ltda. R. Prof. Manoelito de Ornellas, 303, Terro B Chacara Sto. Antonio, CEP : 04719-040 Sao Paulo, SP SAC : 421 http://www.samsung.com.br/ CANADA : Samsung Electronics Canada Inc. Samsung Customer Care 7037 Financial Drive Mississauga, Ontario L5N 6R3 1-800-SAMSUNG (1-800-726-7864) http://www.samsung.ca/ CHILE : SONDA S.A. Teatinos 550, Santiago Centro, Santiago, Chile Fono: 56-2-5605000 Fax: 56-2-5605353 56-2-800200211 http://www.sonda.com/ http://www.samsung.cl/ COLOMBIA : Samsung Electronics Colombia Cra 9 No 99A-02 Of. 106 Bogota, Colombia Tel.: 9-800-112-112 Fax: (571) 618 - 2068 http://www.samsung-latin.com/ e-mail : soporte@samsung-latin.com ESPAA : Samsung Electronics Comercial Iberica, S.A. Ciencies, 55-65 (Poligono Pedrosa) 08908 Hospitalet de Llobregat (Barcelona) Tel. : (93) 00 Fax. : (93) 50 http://samsung.es/ FRANCE : SAMSUNG ELECTRONICS FRANCE Service Paris Nord rue des Vanesses BP 50116 Villepinte 95950 Roissy CDG Cedex Tel : 65 Fax : 38 http://www.samsungservices.com/ GERMANY : TELEPLAN Rhein-Main GmbH Feldstr. Weiterstadt T. 06151/957-1306 F. 06151/957-1732 * EURO 0.12/Min http://www.samsung.de/

FCC Information User Instructions The Federal Communications Commission Radio Frequency Interference Statement includes the following warning: Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television receptions, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. User Information Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. If necessary, consult your dealer or an experienced radio/television technician for additional suggestions. You may find the booklet called How to Identify and Resolve Radio/TV Interference Problems helpful. This booklet was prepared by the Federal Communications Commission. It is available from the U.S. Government Printing Office, Washington, DC 20402, Stock Number 004-000-00345-4. The party responsible for product compliance: SAMSUNG ELECTRONICS CO., LTD America QA Lab of Samsung 3351 Michelson Drive, Suite #290, Irvine, CA92612 USA Tel) 949-975-7310 Fax) 949-922-8301 Warning User must use shielded signal interface cables to maintain FCC compliance for the product. Provided with this monitor is a detachable power supply cord with IEC320 style terminations. It may be suitable for connection to any UL Listed personal computer with similar configuration. Before making the connection, make sure the voltage rating of the computer convenience outlet is the same as the monitor and that the ampere rating of the computer convenience outlet is equal to or exceeds the monitor voltage rating. For 120 Volt applications, use only UL Listed detachable power cord with NEMA configuration 5-15P type

TCO Development SE-Stockholm, Sweden Fax: +07 Email (Internet): development@tco.se Current information regarding TCO'99 approved and labelled products may also be obtained via the Internet, using the address: http://www.tco-info.com/ Environmental requirements Flame retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of flame retardant substances. Most flame retardants contain bromine or chloride, and those flame retardants are chemically related to another group of environmental toxins, PCBs. Both the flame retardants containing bromine or chloride and the PCBs are suspected of giving rise to severe health effects, including reproductive damage in fish-eating birds and mammals, due to the bio-accumulative* processes. Flame retardants have been found in human blood and researchers fear that disturbances in foetus development may occur. The relevant TCO'99 demand requires that plastic components weighing more than 25 grams must not contain flame retardants with organically bound bromine or chlorine. Flame retardants are allowed in the printed circuit boards since no substitutes are available. Cadmium** Cadmium is present in rechargeable batteries and in the colour-generating layers of certain computer displays. Cadmium damages the nervous system and is toxic in high doses. The relevant TCO'99 requirement states that batteries, the colour-generating layers of display screens and the electrical or electronics components must not contain any cadmium. Mercury** Mercury is sometimes found in batteries, relays and switches. It damages the nervous system and is toxic in high doses. The relevant TCO'99 requirement states that batteries may not contain any mercury. It also demands that mercury is not present in any of the electrical or electronics components associated with the labelled unit. There is however one exception. Mercury is, for the time being, permitted in the back light system of flat panel monitors as today there is no commercially available alternative. TCO aims on removing this exception when a Mercury free alternative is available. CFCs (freons) The relevant TCO'99 requirement states that neither CFCs nor HCFCs may be used during the manufacture and assembly of the product. CFCs (freons) are sometimes used for washing printed circuit boards. CFCs break down ozone and thereby damage the ozone layer in the stratosphere, causing increased reception on earth of ultraviolet light with e.g. increased risks of skin cancer (malignant melanoma) as a consequence. Lead** Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the nervous system and in higher doses, causes lead poisoning. The relevant TCO'99 requirement permits the inclusion of lead since no replacement has yet been developed. * Bio-accumulative is defined as substances which accumulate within living organisms. ** Lead, Cadmium and Mercury are heavy metals which are Bio-accumulative.