[UC5000_USA]BN68-02625A-01Eng.indb 9

2010-02-12 9:10:00

Using a Component (up to 1080p) or Audio/Video (480i only) Cable Available devices: DVD, Blu-ray player, cable box, STB satellite receiver, VCR
Video Cable (Not Supplied)

Y R W R W R B G

G B R W R W R Y
Component Cable (Not Supplied)

White Yellow

Blue Green

VIDEO OUT

COMPONENT OUT

PR PB G

COMPONENT IN / AV IN: When connecting to AV IN, the color of the AV IN [Y/VIDEO] jack (green) will not For better picture quality, the Component connection is recomended over the A/V connection.
Using an EX-Link Cable Connection Available Devices: External devices that support EX-Link EX-LINK: Connector for service only. match the video cable (yellow).
[UC5000_USA]BN68-02625A-01Eng.indb 10
Connecting to an Audio Device
Using an Optical (Digital) or Audio (Analog) Cable Connection Available devices: Digital Audio System, Amplifier, DVD home theater
Red White Audio Cable (Not Supplied)

AUDIO IN

Amplifier, DVD home theater
Optical Cable (Not Supplied)

Digital Audio System

OPTICAL
DIGITAL AUDIO OUT (OPTICAL)
of both the TV and the system.
xx When a Digital Audio System is connected to the DIGITAL AUDIO OUT (OPTICAL) jack, decrease the volume xx 5.1 CH (channel) audio is available when the TV is connected to an external device supporting 5.1 CH. xx When the receiver (home theater) is set to on, you can hear sound output from the TVs optical jack. When the
TV is receiving a DTV signal, the TV will send 5.1 CH sound to the home theater receiver. When the source is a digital component such as a DVD / Blu-ray player / cable box / STB (Set-Top-Box) satellite receiver and is connected to the TV via HDMI, only 2 CH audio will be heard from the home theater receiver. If you want to hear 5.1 CH audio, connect the digital audio out jack from your DVD / Blu-ray player / cable box / STB satellite receiver directly to an amplifier or home theater.

OO MENUm Channel Channel List ENTERE
Add to Favorite / Delete from Favorite
Set channels you watch frequently as Favorites. 1. Select a channel and press the TOOLS button. 2. Add or delete a channel using the Add to Favorite or Delete from Favorite menu respectively.

6 6-1 Air * TV #6

Channel List
OO MENUm Channel Channel List
ENTERE Select a channel in the All Channels, Added Channels, Favorite or Programmed screen by pressing the / and ENTERE buttons. Then you can watch the selected channel.
Add, delete or set Favorite channels and use the program guide for digital broadcasts.

Added Channels

9-10-1 11-1

Air Antenna

Air Air * TV #9 Air * TV #10 * TV #11
Delete Add to Favorite Timer Viewing Channel Name Edit Select All

Antenna

Select kPage T Tools
To show all Favorite channels, click on the button shown on the right.
All Channels: Shows all currently available channels. Added Channels: Shows all added channels.
* Favorite: Shows all favorite channels.
Programmed: Shows all currently reserved programs.

Memorizing Channels

Using the color buttons with the Channel List.

number.

OO MENUm Channel ENTERE

Antenna (Air / Cable) t

Before your television can begin memorizing the available channels, you must specify the type of signal source that is connected to the TV (i.e. an Air or a Cable system).
xx Red (Antenna): Switches to Air or Cable. xx B Green (Zoom): Enlarges or shrinks a channel xx
Yellow (Select): Selects multiple channel lists. Select desired channels and press the Yellow button to set all the selected channels at the same time. The c mark appears to the left of the selected channels.
xx k (Page): Move to next or previous page. xx T (Tools): Displays the Channel List option menu.
(The Options menus may differ depending on the situation.) Channel Status Display Icons Icons c * ) Operations A channel selected. A channel set as a Favorite. A reserved Program.

Auto Program

Air: Air antenna signal. Cable: Cable antenna signal. Auto: Air and Cable antenna.
[UC5000_USA]BN68-02625A-01Eng.indb 14

2010-02-12 9:10:04

xx When selecting the Cable TV system: STD, HRC
Add / Delete: Delete or add a channel to display the channels you want.
and IRC identify various types of cable TV systems. Contact your local cable company to identify the type of cable system that exists in your particular area. At this point, the signal source has been selected. to remove scrambled channels. The Auto Program menu then reappears.
xx All deleted channels will be shown on the All

Energy Saving (Off / Low / Medium / High / Picture Off / Auto): This adjusts the brightness of the TV in order to reduce power consumption. If you select Picture Off, the screen is turned off, but the sound remains on. Press any button to turn on the screen again. Eco Sensor (Off / On): To enhance your power savings; the picture settings will automatically adapt to the light in the room.
OO MENUm Picture Mode ENTERE
Select your preferred picture type. Dynamic: Suitable for a bright room. Standard: Suitable for a normal environment. Natural: Suitable for reducing eye strain.

P.MODE

If you adjust the Backlight, the Eco Sensor will

be set to Off.

Natural is not available in PC mode.
Movie: Suitable for watching movies in a dark room.
Min Backlight: When Eco sensor is On, the minimum screen brightness can be adjusted manually. If Eco Sensor is On, the display brightness may change (become slightly darker in most cases) depending on the surrounding light intensity.
No Signal Power Off (Off / 15 min / 30 min / 60 min): To avoid unnecessary energy consumption, set how long you want the TV to remain on if it's not receiving a signal.
Disabled when the PC is in power saving mode.
[UC5000_USA]BN68-02625A-01Eng.indb 16
Changing the Picture Options

Picture Options

Advanced Settings
OO MENUm Picture Picture Options

ENTERE

OO MENUm Picture Advanced Settings
ENTERE (Advanced Settings are available in Standard / Movie mode) Compared to previous models, new Samsung TVs have a more precise picture.
In PC mode, you can only make changes to the Color
Color Tone Size Digital Noise Filter MPEG Noise Filter HDMI Black Level Film Mode Auto Protection Time : Normal : 16:9 : Auto : Auto : Normal : Off : 2 hours

U Move E Enter R Return

Tone, Size, Digital Noise Filter and Auto Protection Time.
In PC mode, you can only make changes to Dynamic
Contrast, Gamma, White Balance and LED Motion Plus.
Black Tone Dynamic Contrast Shadow Detail Gamma RGB Only Mode Color Space White Balance
: Off : Medium : -2 :0 : Off : Native
Color Tone (Cool / Normal / Warm1 / Warm2)
Warm1 or Warm2 will be deactivated when the picture Settings can be adjusted and stored for each external
device connected to an input on the TV. Size: Your cable box/satellite receiver may have its own set of screen sizes as well. However, we highly recommend you use 16:9 mode most of the time. mode is Dynamic.
Black Tone (Off / Dark / Darker / Darkest): Select the black level to adjust the screen depth. Dynamic Contrast (Off / Low / Medium / High): Adjust the screen contrast. Shadow Detail (-2~+2): Increase the brightness of dark images. Gamma: Adjust the primary color intensity. RGB Only Mode (Off / Red / Green / Blue): Displays the Red, Green and Blue color for making fine adjustments to the hue and saturation. Color Space (Auto / Native / Custom): Adjust the range of colors available to create the image. To adjust Color, Red, Green, Blue and Reset, set Color Space to Custom. White Balance: Adjust the color temperature for a more natural picture. R-Offset / G-Offset / B-Offset: Adjust each color's (red, green, blue) darkness. R-Gain / G-Gain / B-Gain: Adjust each color's (red, green, blue) brightness. Reset: Resets the White Balance to it's default settings. Flesh Tone: Emphasize pink Flesh Tone. Edge Enhancement (Off / On): Emphasize object boundaries. LED Motion Plus (Off / On): Removes drag from fast scenes with a lot of movement to provide a clear picture.

P.SIZE

16:9: Sets the picture to 16:9 wide mode. Zoom1: Use for moderate magnification. Zoom2: Use for a stronger magnification. Wide Fit: Enlarges the aspect ratio of the picture to fit the entire screen. Available for HD 1080i / 720p signal in 16:9 mode.
4:3: Sets the picture to basic (4:3) mode. Do not watch in 4:3 format for a long time. Traces of borders displayed on the left, right and center of the screen may cause image retention(screen burn) which are not covered by the warranty. Screen Fit: Displays the full image without any cut-off when HDMI (720p / 1080i / 1080p) or Component (1080i / 1080p) signals are inputted.
xx After selecting Zoom1, Zoom2 or Wide Fit:
1. Press the button to select Position. 2. ress the ENTERE button. P 3. Press the or button to move the picture up or down. 4. Press the ENTERE button. 5. Press the button to select Reset. 6. Press the ENTERE button to reset the picture to its default position.
[UC5000_USA]BN68-02625A-01Eng.indb 17

2010-02-12 9:10:06

xx After selecting Screen Fit in HDMI (1080i/1080p) or
Component (1080i/1080p) mode, you may need to center the picture: 1. Press the or button to select Position. 2. Press the ENTERE button. 3. Press the , , or button to move the picture. 4. Press the ENTERE button. 5. Press the or button to select Reset. 6. Press the ENTERE button.
Picture Reset (OK / Cancel)
Resets your current picture mode to its default settings.
Setting up the TV with Your PC
Set the input source to PC.

Auto Adjustment t

Adjust frequency values/positions and fine tune the settings automatically.
xx HD (High Definition): 16:9 - 1080i/1080p (1920x1080),

720p (1280x720)

xx Settings can be adjusted and stored for each
Input Source ATV, AV, Component (480i, 480p) DTV(1080i), Component (1080i, 1080p), HDMI (720p, 1080i, 1080p) PC Picture Size 16:9, Zoom1, Zoom2, 4:3
external device you have connected to an input on the TV.
Not available when connecting with an HDMI/DVI cable.

Screen

Coarse / Fine: Removes or reduces picture noise. If the noise is not removed by Fine-tuning alone, then adjust the frequency as best as possible (Coarse) and Finetune again. After the noise has been reduced, readjust the picture so that it is aligned to the center of screen. Position: Adjust the PCs screen positioning if it does not fit the TV screen. Press the or button to adjust the Vertical-Position. Press the or button to adjust the Horizontal-Position. Image Reset: Resets the image to default settings. Using Your TV as a Computer (PC) Display Setting Up Your PC Software (Based on Windows XP) Depending on the version of Windows and the video card, the actual screens on your PC will probably look different, but the same basic set-up information will apply in most cases. (If not, contact your computer manufacturer or Samsung Dealer.) 1. Click on Control Panel on the Windows start menu. 2. Click on Appearance and Themes in the Control Panel window and a display dialog-box will appear. 3. Click on Display and a display dialog box will appear. 4. Navigate to the Settings tab on the display dialog-box. yy The correct size setting (resolution) [Optimum: 1920 X 1080 pixels] yy If a vertical-frequency option exists on your display settings dialog box, the correct value is 60 or 60 Hz. Otherwise, just click OK and exit the dialog box.

16:9, 4:3, Wide Fit, Screen Fit 16:9, 4:3
Digital Noise Filter (Off / Low / Medium / High / Auto / Auto Visualisation): If the broadcast signal received by your TV is weak, you can activate the Digital Noise Filter (Noise Reduction) feature to reduce any static and ghosting that may appear on the screen. best picture is displayed.
When the signal is weak, try other options until the When bar is green, you are receiving the best

possible signal.

Auto Visualisation: When changing analog channels, displays signal strength. Only available for analog channels.
MPEG Noise Filter (Off / Low / Medium / High / Auto): Reduces MPEG noise to provide improved picture quality. HDMI Black Level (Normal / Low): Selects the black level on the screen to adjust the screen depth.
Available only in HDMI mode.
Film Mode (Off / Auto1 / Auto2): Sets the TV to automatically sense and process film signals from all sources and adjusts the picture for optimum quality. and HDMI (480i / 1080i).
Available in TV, AV, COMPONENT (480i / 1080i)
Auto Protection Time (2 hours / 4 hours / 8 hours / 10 hours / Off): Set the time the screen remains idle with a still image until the screen saver is activated. The screen saver prevents the formation of ghost images on the screen.
[UC5000_USA]BN68-02625A-01Eng.indb 18

Sound Menu

Preferred Language
(digital channels only) Digital-TV broadcasts are capable of simultaneous transmission of many audio tracks (for example, simultaneous translations of the program into foreign languages). ones being broadcasted.
Changing the Preset Sound Mode
OO MENUm Sound Mode ENTERE
Standard: Selects the normal sound mode. Music: Emphasizes music over voices. Movie: Provides the best sound for movies. Clear Voice: Emphasizes voices over other sounds. Amplify: Increase the intensity of high-frequency sound to allow a better listening experience for the hearing impaired.
You can only select a language among the
Multi-Track Sound (MTS) t
(analog channels only) Mono: Choose for channels that are broadcasting in mono or if you are having difficulty receiving a stereo signal. Stereo: Choose for channels that are broadcasting in stereo. SAP: Choose to listen to the Separate Audio Program, which is usually a foreign-language translation.

Adjusting Sound Settings

Depending on the particular program being broadcast,
you can listen to Mono, Stereo or SAP.

OO MENUm Sound ENTERE

Equalizer
Adjusts the sound mode (standard sound mode only). Balance L/R: Adjusts the balance between the right and left speaker. 100Hz / 300Hz / 1kHz / 3kHz / 10kHz (Bandwidth Adjustment): Adjusts the level of specific bandwidth frequencies. Reset: Resets the equalizer to its default settings.

Auto Volume (Off / Normal / Night)
To equalize the volume level on each channel, set to Normal. Night: This mode provides an improved sound experience compared to Normal mode, making almost no noise. It is useful at night.
Speaker Select (External Speaker / TV Speaker)
A sound echo may occur due to a difference in decoding speed between the main speaker and the audio receiver. In this case, set the TV to External Speaker. volume and MUTE buttons will not operate and the sound settings will be limited.

Sound Settings

When Speaker Select is set to External Speaker, the When Speaker Select is set to External Speaker. When Speaker Select is set to TV Speaker. If there is no video signal, both speakers will be mute.
xx TV Speaker: On , External Speaker: On xx TV Speaker: Off , External Speaker: On
Virtual Surround (Off / On)
(standard sound mode only) This function provides a virtual 5.1 channel surround sound experience through a pair of speakers or headphones using HRTF (Head Related Transfer Function) technology.
Dialog Clarity (Off / On)
(standard sound mode only) This function allows you to increase the intensity of a voice over background music or sound effects so that dialog can be heard more clearly.
[UC5000_USA]BN68-02625A-01Eng.indb 19

2010-02-12 9:10:07

SPDIF Output
SPDIF (Sony Philips Digital Interface) is used to provide digital sound, reducing interference going to speakers and various digital devices such as an A/V Receiver/Home theater. Audio Format: During the reception of a digital TV broadcast, you can select the Digital Audio output (SPDIF) format from the options PCM or Dolby Digital. Audio Delay: Correct audio-video sync problems, when watching TV or video, and when listening to digital audio output using an external device such as an AV receiver (0ms ~ 250ms).

Using the Sleep Timer

OO MENUm Setup Time Sleep Timer
ENTERE Sleep Timer: Automatically shuts off the TV after a preset period of time. (30, 60, 90, 120, 150 and 180 minutes).
To cancel the Sleep Timer, select
Setting the On / Off Timer

xx If there is no music file on the USB device or the xx When there is only one photo file in the USB,
the Slide Show will not play. selected.
folder containing a music file is not selected, the Timer function does not operate correctly.
xx If a folder name is too long, the folder cannot be xx Each USB you use is assigned its own folder.
When using more than one of the same type of USB, make sure the folders assigned to each USB have different names.
Auto Power Off (available only when the TV is turned

Locking Programs

Repeat: Select Once, Everyday, Mon~Fri, Mon~Sat, Sat~Sun or Manual to set at you convenience. If you select Manual, you can set up the day you want to activate the timer. The c mark indicates the day is selected. on by the Timer): The TV will be automatically turned off after 3 hours of being left idle to prevent overheating.
TV Parental Guidelines: You can block TV programs depending on their rating. This function allows you to control what your children are watching. TV-Y: Young children / TV-Y7: Children 7 and over / TV-G: General audience / TV-PG: Parental guidance / TV-14: Viewers 14 and over / TV-MA: Mature audience ALL: Lock all TV ratings. / FV: Fantasy violence / V: Violence / S: Sexual situation / L: Adult Language / D: Sexually Suggestive Dialog The V-Chip will automatically block certain categories dealing with more sensitive material. For example, if you block the TV-Y category, then TV-Y7 will automatically be blocked. Similarly, if you block the TV-G category, then all the categories in the young adult group will be blocked (TV-G, TV-PG, TV-14 and TV-MA). The sub-ratings (D, L, S, V) work similarly. So, if you block the L sub-rating in TV-PG, then the L sub-ratings in TV-14 and TV-MA will automatically be blocked.
OO MENUm Setup Security ENTERE

Security

The PIN input screen appears, Enter your 4 digit PIN number. V-Chip: The V-Chip feature automatically locks out programs that are deemed inappropriate for children. The user must enter a PIN (personal identification number) before any of the V-Chip restrictions are set up or changed.
MPAA Rating: You can block movies depending on their MPAA rating. The Motion Picture Association of America(MPAA) has implemented a rating system that provides parents or guardians with advanced information on which films are appropriate for children. G: General audience (no restrictions). / PG: Parental guidance suggested. / PG-13: Parents strongly cautioned. / R: Restricted. Children under 17 should be accompanied by an adult. / NC-17: No children under age 17. / X: Adults only. / NR: Not rated. The V-Chip will automatically block any category that deals with more sensitive material. For example, if you block the PG-13 category, then R, NC-17 and X will automatically be blocked.

Support Menu
OO MENUm Setup Support ENTERE

Self Diagnosis

Picture Test: Use to check for picture problems. Yes: If the test pattern does not appear or there is noise in the test pattern, select Yes. There may be a problem with the TV. Contact Samsungs Call Center for assistance (1-800-SAMSUNG). No: If the test pattern is properly displayed, select No. There may be a problem with your external equipment. Please check your connections. If the problem persists, refer to the external devices user manual. Sound Test: Use the built-in melody sound to check for sound problems.

Software Upgrade

Current Version 2010/01/18_000001
By USB By Online Alternative Software

2010/01/15_00000

Installing the Latest Version By USB: Insert a USB drive TV Rear Panel containing the firmware upgrade file, downloaded from www.samsung.com, or into the TV. Please be careful not to disconnect the power or remove the USB drive USB Drive until upgrades are complete. The TV will be turned off and on automatically after completing the firmware upgrade. When software is upgraded, video and audio settings you have made will return to their default settings. We advise you to to write down your settings so that you can easily reset them after the upgrade. By Online: Upgrade the software using the Internet.
If you hear no sound from the TVs speakers,
before performing the sound test, make sure Speaker Select is set to TV Speaker in the Sound menu.
The melody will be heard during the test even if
Speaker Select is set to External Speaker or the sound is muted by pressing the MUTE button.
Yes: If you can hear sound only from one speaker or not at all during the sound test, select Yes. There may be a problem with the TV. Contact Samsungs Call Center for assistance (1-800-SAMSUNG). No: If you can hear sound from the speakers, select No. There may be a problem with your external equipment. Please check your connections. If the problem persists, refer to the external devices user manual. Signal Information: (Digital channels only) An HD channels reception quality is either perfect or the channels are unavailable. Adjust your antenna to increase signal strength. Troubleshooting: If the TV seems to have a problem, refer to this description. the Samsung customer service center.

Connecting to a Wireless Network
To connect your TV to your network wirelessly, you need a wireless router or modem and a Samsung Wireless LAN Adapter (WIS09ABGN), which you connect to your TVs back or side panel USB jack. See the illustration below.

The LAN Port on the Wall

Wireless IP sharer (AP having DHCP Server)

TV Rear Panel

Samsung Wireless LAN Adapter
Samsungs Wireless LAN adapter is sold separately and is offered by select retailers, Ecommerce sites and Samsungparts. com. Samsungs Wireless LAN adapter supports the IEEE 802.11A/B/G and N communication protocols. Samsung recommends using IEEE 802.11N. When you play the video over a IEEE 802.11B/G connection, the video may not play smoothly.
xx You must use the Samsung Wireless LAN Adapter (WIS09ABGN) to use a wireless network. xx Samsungs Wireless LAN adapter is sold separately. The WIS09ABGN Wireless LAN adapter is offered by select
retailers, Ecommerce sites and Samsungparts.com.
xx To use a wireless network, your TV must be connected to a wireless IP sharer. If the wireless IP sharer supports
DHCP, your TV can use a DHCP or static IP address to connect to the wireless network.
xx Select a channel for the wireless IP sharer that is not currently being used. If the channel set for the wireless IP sharer
is currently being used by another device nearby, this will result in interference and communication failure.
xx If you apply a security system other than the systems listed blow, it will not work with the TV. xx If Pure High-throughput (Greenfield) 802.11n mode is selected and the Encryption type is set to WEP, TKIP or xx If your AP supports WPS (Wi-Fi Protected Setup), you can connect to the network via PBC (Push Button
TKIPAES (WPS2Mixed) for your AP, Samsung TVs will not support a connection in compliance with new Wi-Fi certification specifications. Configuration) or PIN (Personal Identification Number). WPS will automatically configure the SSID and WPA key in either mode.
xx If your router, modem, or device isnt certified, it may not connect to the TV via the Samsung Wireless LAN Adapter. xx Connection Methods: You can setup the wireless network connection four ways.
PBC (WPS) Auto Setup (Using the Auto Network Search function) Manual Setup Ad-Hoc
xx All of Samsung Wireless LAN Adapter shoud be connected directly to the TV's USB port. USB HUB are not

[UC5000_USA]BN68-02625A-01Eng.indb 37

2010-02-12 9:10:21

Anynet+ Menu The Anynet+ menu changes depending on the type and status of the Anynet+ devices connected to the TV. Anynet+ Menu View TV Device List (device_name) MENU (device_name) INFO Recording: (*recorder) Stop Recording: (*recorder) Receiver Description Changes Anynet+ mode to TV broadcast mode. Shows the Anynet+ device list. Shows the connected device menus. E.g. If a DVD recorder is connected, the disc menu of the DVD recorder will appear. Shows the play menu of the connected device. E.g. If a DVD recorder is connected, the play menu of the DVD recorder will appear. Starts recording immediately using the recorder. (This is only available for devices that support the recording function.) Stops recording. Sound is played through the receiver.
If more than one recording device is connected, they are displayed as (*recorder) and if only one recording device is connected, it will be represented as (*device_name).

Setting Up Anynet+

OO MENUm Application Anynet+ (HDMI-CEC) ENTERE

Setup

When the Anynet+ (HDMI-CEC) function is disabled, all the Anynet+ related operations are deactivated.
Auto Turn Off (No / Yes): Setting an Anynet+ Device to turn off automatically when the TV is turned off. The active source on the TV must be set to TV to use the Anynet+ function.
Anynet+ (HDMI-CEC) (Off / On): To use the Anynet+ Function, Anynet+ (HDMI-CEC) must be set to On.
Even if an external device is still recording, it may turn off.
Switching between Anynet+ Devices
1. Anynet+ devices connected to the TV are listed.
If you cannot find a device you want, press the Red button to refresh the list. Only when you set Anynet+ (HDMI-CEC) to On in the Application menu, the Device List menu appears.
xx Switching to the selected device may take up to 2 minutes. You cannot cancel the operation during the switching

operation.

2. Select a device and press the ENTERE button. You can switch to the selected device.
xx If you have selected external input mode by pressing the SOURCE button, you cannot use the Anynet+ function.
Make sure to switch to an Anynet+ device by using the Device List.

Recording

You can make a recording of a TV Program using a Samsung recorder. 1. Select Recording.
When there are more than two recording devices

the Device List.

xx When multiple recording devices are connected, the recording devices are listed. Select one recording device in
When the recording device is not displayed, select Device List and press the Red button to search devices.
2. Press the EXIT button to exit.
You can record the source streams by selecting Recording: (device_name). Pressing the (REC) button will record whatever you are currently watching. If you are watching video from Before recording, check whether the antenna jack is properly connected to the recording device. To properly
connect an antenna to a recording device, refer to the recording devices users manual. another device, the video from the device is recorded.
[UC5000_USA]BN68-02625A-01Eng.indb 38
Listening through a Receiver
You can listen to sound through a receiver (i.e Home Theater) instead of the TV Speaker. 1. Select Receiver and set to On. 2. Press the EXIT button to exit.
If your receiver supports audio only, it may not appear in the device list. The receiver will work when you have properly connected the optical in jack of the receiver to the DIGITAL AUDIO When the receiver (i.e Home Theater) is set to On, you can hear sound output from the TVs Optical jack. When NOTE
OUT (OPTICAL) jack of the TV. the TV is displaying a DTV (air) signal, the TV will send out 5.1 channel sound to the receiver. When the source is a digital component such as a DVD and is connected to the TV via HDMI, only 2 channel sound will be heard from the receiver.
xx You can only control Anynet+ devices using the TV remote control, not the buttons on the TV. xx The TV remote control may not work under certain conditions. If this occurs, reselect the Anynet+ device. xx The Anynet+ functions do not operate with other manufacturers products.
Troubleshooting for Anynet+
Problem Anynet+ does not work. Possible Solution Check if the device is an Anynet+ device. The Anynet+ system supports Anynet+ devices only. Only one receiver (home theater) can be connected. Check if the Anynet+ device power cord is properly connected. Check the Anynet+ devices Video/Audio/HDMI cable connections. Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu. Check whether the TV remote control is in TV mode. Check whether the remote control is Anynet+ compatible. Anynet+ doesnt work in certain situations. (Searching channels, operating Media Play or Plug & Play (initial setup), etc.) When connecting or removing the HDMI cable, please make sure to search devices again or turn your TV off and on again. Check if the Anynet+ Function of Anynet+ device is set on. Check if the Anynet+ device is properly connected to the TV and check if the Anynet+ (HDMI-CEC) is set to On in the Anynet+ Setup menu. Press the TOOLS button to display the Anynet+ menu and select a menu you want. Select View TV in the Anynet+ menu. Press the SOURCE button on the TV remote control and select a non- Anynet+ device. Press z, PRE-CH, and FAV.CH to change the TV mode. (Note that the channel button operates only when a tuner-embedded Anynet+ device is not connected.) You cannot use the remote control when you are configuring Anynet+ or switching to a view mode. Use the remote control when the Anynet+ setting or switching to view mode is complete. You cannot use the play function when Plug & Play (initial setup) is in progress. Check whether or not the device supports Anynet+ functions. Check whether or not the HDMI cable is properly connected. Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu. Search Anynet+ devices again. You can connect an Anynet+ device using the HDMI cable only. Some HDMI cables may not support Anynet+ functions. If connection is terminated because there has been a power interruption or the HDMI cable has been disconnected, please repeat the device scan. Check whether the antenna jack on the recording device is properly connected. Connect the optical cable between TV and the receiver.

I want to start Anynet+.

I want to exit Anynet+.
The message Connecting to Anynet+ device. appears on the screen. The Anynet+ device does not play. The connected device is not displayed.
The TV Program cannot be recorded. The TV sound is not output through the receiver.
[UC5000_USA]BN68-02625A-01Eng.indb 39

AllShare

Message / Media / ScreenShare
Shows a list of mobile phones or connected devices which have been set up with this TV for using the Message, Media, or ScreenShare function.
OO MENUm Application Content View

AllShare ENTERE

About AllShare
AllShare connects your TV and compatible Samsung mobile phones/ devices through a network. On your TV, you can view call arrivals, SMS messages and schedules set on your mobile phones. In addition, you can play media contents including videos, photos and music saved on your mobile phones or the other devices (such as your PC) by controlling them on the TV via the network. Additionally, you can use your TV for browsing web pages in your mobile phones. contact the Samsung call center. Mobile devices may need additional software installation. For details, refer to each devices users guide.
The Media function is available in all mobile devices
which support AllShare. Allowed / Denied: Allows/Blocks the mobile phone. Delete: Deletes the mobile phone from the list.
This function only deletes the name of the mobile
from the list. If the deleted mobile device is turned on or trys to connect to the TV, it may appear on the list again.
For more information, visit www.samsung.com or
Using the Message Function Using this function, you view call arrivals, SMS messages and schedules set on the mobile phone through the alarm window while watching TV.

Setting Up AllShare

xx To disable the alarm window, set Message to Off in

Setup of AllShare.

Message (On / Off): Enables or disables the message function (for call arrivals, SMS messages and schedules set on your mobile phones). Media (On / Off): Enables or disables the media function. When the media function is on, it plays videos, photos and music from a mobile phone or other device that supports AllShare. ScreenShare (On / Off): Enables or disables the ScreenShare function for using mobile phone as a remote control. TV name: Sets the TV name so you can find it easily on a mobile device.

No Caption on digital channels. The picture is distorted: macroblock error, small block, dots, pixelization. PC Connection A Mode Not Supported message appears. PC is always shown on the source list, even if a PC is not connected. The video is OK but there is no audio. Network Connection The wireless network connection failed.
Set your PCs output resolution so they matche the resolutions supported by the TV (p. 12). This is normal; PC is always shown on the source list, regardless of whether a PC is connected. If you are using an HDMI connection, check the audio output setting on your PC.
The Samsung Wireless USB dongle is required to use a wireless network. Make sure the Network Connection is set to Wireless (p. 27). Make sure the TV is connected to a wireless IP sharer (router). Try network test in Setup menu (p. 23). If you have latest SW version, SW upgrade will not proceed.
Software Upgrade over the network fails. Others Purple/green rolling horizontal bars and buzzing noise from the TV speakers with Component cable connection. The picture wont display in full screen.
Remove the left and right audio connections from the set-top-box. If the buzzing stops, this indicates that the set-top-box has a grounding issue. Replace the Component video cables with an HDMI connection. HD channels will have black bars on either side of the screen when displaying upscaled SD (4:3) contents. Black bars on the Top & Bottom will appear during movies that have aspect ratios different from your TV. Adjust the picture size options on your external device or TV to full screen. Replace the remote control batteries with the poles (+/) in the right direction. Clean the sensors transmission window on the remote. Try pointing the remote directly at the TV from 5~6 feet away. Program the Cable/Sat remote control to operate the TV. Refer to the Cable/Set user manual for the SAMSUNG TV code.
The remote control does not work.
The cable/set top box remote control doesnt turn the TV on or off, or adjust the volume.
[UC5000_USA]BN68-02625A-01Eng.indb 47

2010-02-12 9:10:29

A Mode Not Supported message appears. Caption on TV menu is greyed out. There is a plastic smell from the TV. The TV Signal Information is unavailable in the Self Diagnostic Test menu. The TV is tilted to the side. The channel menu is greyed out (unavailable). Your settings are lost after 30 minutes or every time the TV is turned off. You have intermittent loss of audio or video.
Check the supported resolution of the TV, and adjust the external devices output resolution accordingly. Refer to the resolution settings on page 12 of this manual. Caption can not be selected in the TV menu when connected via HDMI or Component (p. 22). Caption must be activated on the external device (p. 22). This smell is normal and will dissipate over time. This function is only available with digital channels from an Antenna/RF/Coax connection (p. 24). Remove the base stand from the TV and reassemble it. The Channel menu is only available when the TV source is selected. If the TV is in the Store Demo mode, it will reset audio and picture settings every 30 minutes. Change the settings from Store Demo mode to Home Use mode in the Plug & Play procedure. Press the SOURCE button to select TV mode, and go to MENU Setup Plug & Play ENTERE (p. 8). Check the cable connections and reconnect them. Loss of audio or video can be caused by using overly rigid or thick cables. Make sure the cables are flexible enough for long term use. If mounting the TV to a wall, we recommend using cables with 90 degree connectors. This is part of the products design and is not a defect. Select Home Use under Plug & Play mode. For details, refer to Plug & Play Feature (p. 8).

Samsung UN40CInch 1080p LED HDTV
You may be in the market to seek out a new flat screen HD television for your new home. However, you may be having second thoughts as to what type to buy. There are so many options available for you. One of the best HDTV that you may want to consider is the new Samsung UN40C5000 40-Inch 1080p LED HDTV. You can never really go wrong with its sleek high-class appearance. The new Samsung LED 1080p TV will definitely become your home's new star.
Television has become the major home entertainment for most families on this planet. People enjoy watching television given it offers us a wide range of fun and enjoyable forms of entertainment to relax our mind and body.
While using great audio and video systems combined, you movies will surely look so alive. You will realize that watching TV is not the same thing again. With this new high definition LED TV, you will realize that you wil have less time for Facebook again.
Samsung UN40C5000's perfect proportions and stylish design will be at home in your home wherever you put it. It can be paired great with your home's interior. The Samsung LED 1080p TV is not only just an ordinary appliance; instead it can be considered as a work of art with its sleek and classy design. You can definitely get a lot of praises from your friends and visitors if they see it.
IN deciding where to position the Samsung LED 1080p TV is never a big problem for you. You can swivel it either to the left or to the right. Moreover, it has a unique wide viewing angle that cannot be found easily on the other LCD TVs. If you possess the Samsung LED 1080p TV, you won't find it hard to look for the best seat.

About the Author

Interested to know about hd tv reviews? If so better read hd tv reviews quickly.
Source: http://readerspot.com