Precautions
11. High voltage is maintained within specified limits by close-tolerance, safety-related components and adjustments. If the high voltage exceeds the specified limits, check each of the special components. 12. Design Alteration Warning : Never alter or add to the mechanical or electrical design of this unit. Example : Do not add auxiliary audio or video connectors. Such alterations might create a safety hazard. Also, any design changes or additions will void the manufacturers warranty. 13. Hot Chassis Warning : Some TV receiver chassis are electrically connected directly to one conductor of the AC power cord. If an isolation transformer is not used, these units may be safely serviced only if the AC power plug is inserted so that the chassis is connected to the ground side of the AC source. To confirm that the AC power plug is inserted correctly, do the following : Using an AC voltmeter, measure the voltage between the chassis and a known earth ground. If the reading is greater than 1.0V, remove the AC power plug, reverse its polarity and reinsert. Re-measure the voltage between the chassis and ground. 14. Some TV chassis are designed to operate with 85 volts AC between chassis and ground, regardless of the AC plug polarity. These units can be safely serviced only if an isolation transformer inserted between the receiver and the power source. 15. Never defeat any of the B+ voltage interlocks. Do not apply AC power to the unit (or any of its assemblies) unless all solid-state heat sinks are correctly installed. 16. Always connect a test instruments ground lead to the instrument chassis ground before connecting the positive lead; always remove the instruments ground lead last.
17. Observe the original lead dress, especially near the following areas : Antenna wiring, sharp edges, and especially the AC and high voltage power supplies. Always inspect for pinched, out-of-place, or frayed wiring. Do not change the spacing between components and the printed circuit board. Check the AC power cord for damage. Make sure that leads and components do not touch thermally hot parts. 18. Picture Tube Implosion Warning : The picture tube in this receiver employs integral implosion protection. To ensure continued implosion protection, make sure that the replacement picture tube is the same as the original. 19. Do not remove, install or handle the picture tube without first putting on shatterproof goggles equipped with side shields. Never handle the picture tube by its neck. Some in-line picture tubes are equipped with a permanently attached deflection yoke; do not try to remove such permanently attached yokes from the picture tube. 20. Product Safety Notice : Some electrical and mechanical parts have special safety-related characteristics which might not be obvious from visual inspection. These safety features and the protection they give might be lost if the replacement component differs from the original--even if the replacement is rated for higher voltage, wattage, etc. Components that are critical for safety are indicated in the circuit diagram by shading, ( or ). Use replacement components that have the same ratings, especially for flame resistance and dielectric strength specifications. A replacement part that does not have the same safety characteristics as the original might create shock, fire or other hazards.

NO-OSD-DISPLAY ADDR MODEL/DATA PAL HI8 ADDR 05A 05B 05C 05D 05E 05F 06A 06B 06C 06D 06E 06F 07A 07B DATA 5A 04 E10 2A 10 2A 08 0D 1B 82 C0 F0 EE 7D 5A 2C E10 2A 10 2A 08 0D 1B 82 C0 F0 EE 7D 2C 3B E10 2A 10 2A 15 2C 4D 70 B4 F8 EE 68 4B 3D 2C 1D 4E 04 E10 2A 10 2A 15 2C 4D 70 B4 F8 EE 4A NORMAL HI8 NTSC NORMAL D7 BIT SEGMENTATION EXPLAIN D6 D5 D4 D3 B CONTROL 5100K D2 D1 D0 CONTENT (EEPROM DATA PAGE 0)
changed by AUTO AWB ADJ(0CF) @DSP#12C( HAPGN) at AGC @DSP#12C (HAPGN) at AGC "* AWB- RATIO ; 1/3 CENTER TRACKING"
"* AWB- RATIO HIGH ; CENTER AXIS OVER 5100K(OUTDOOR)" "* AWB- RATIO LOW ; CENTER AXIS BELOW 3100K(INDOOR)" SHUTTER START POINT OF IRIS CONTROL PERCENT(FF=100% IRIS MAX) "@WDR ON; AE DATA CUTTING -LOW" "@WDR ON; AE DATA CUTTING -HIGH" "@WDR ON; BLACK BALANCE MAX-DATA (MIN DATA+31)" "@WDR ; AE-TARGET MARGIN; #087,#088 -#060, AT CLIP-COUNTER ON " "@WDR ; CLIP_COUNTER-TH-'HIGH' BYTE " @EIS H-TH-COUNTER @EIS H-TH @EIS V-TH-COUNTER @EIS V-TH "@WDR ON; Y ,C GAMMA 1 " "@WDR ON; Y ,C GAMMA 2 " "@WDR ON; Y,C GAMMA 3 " "@WDR ON; Y ,C GAMMA 4 " "@WDR ON; Y,C GAMMA 5 " "@WDR ON; Y,C GAMMA 6" "@WDR ON; Y ,C GAMMA 7" "@WDR ON; Y,C GAMMA 8" "@WDR ON; ADDR#12C ;YVBKT,YVBK,HBLK,YHBK" "@WDR ON; ADDR#123;YHPSC,YAPC" "@WDR ON; ADDR#126;YLPFSEL" "@WDR ON; ADDR#134;RED DARK SLICE" "@WDR ON; ADDR#135;BLUE DARK SLICE" "@WDR ON; ADDR#136;GREEN DARK SLICE" @CINEMA F-ZONE LIMIT UP @CINEMA F-ZONE LIMIT UP @R-GAIN POSITIVE(ADDR.147) at OUTDOOR @R-GAIN NEGATIVE(ADDR.148) at OUTDOOR @R-HUE POSITIVE (ADDR.149) at OUTDOOR @R-HUE NEGATIVE (ADDR.14A) at OUTDOOR @B-GAIN POSITIVE(ADDR.14B) at OUTDOOR @B-GAIN NEGATIVE(ADDR.14C) at OUTDOOR
NO-OSD-DISPLAY ADDR MODEL/DATA PAL HI8 ADDR 07C 07D 07E 07F 08A 08B 08C 08D 08E 08F 09A 09B 09C 09D 09E 09F 0A0 0A1 DATA 1C 5E 0C 75 3A F0 FF F1C B98 B1C F0B 0B 18 A0 1A 0E 04 5E 0C 75 3A F0 FF 0C 98 B1C F0B 0B 20 A5E 0C 75 3A F0 FF FB1C F0B 0B 18 A0D 04 5E 0C 75 3A F0 FF 0A 02 F09 EE B1C F0B 0B 20 A0 NORMAL HI8 NTSC NORMAL D7 BIT SEGMENTATION EXPLAIN D6 D5 D4 D3 D2 D1 D0 CONTENT (EEPROM DATA PAGE 0)
@B-HUE POSITIVE (ADDR.14D) at OUTDOOR @B-HUE NEGATIVE (ADDR.14E) at OUTDOOR @NEGA BLC TARGET-'L' @NEGA BLC TARGET-'H' "@AE; AE A-WINDOW WEIGHT '05'=50%" "@AE; SPOTLIGHT AE-TARGET 'L'" "@AE; SPOTLIGHT AE-TARGET 'H'" @DIGITAL CLAMP CONTROL START AGC @AGC MAX , DIGITAL CLAMP CONTROL(ADDR.#118) * AWB- W/B DATA-TH * AWB- LUMINANCE AREA NUMBER "@AE; BLC/WDR , AE TARGET 'L'" "@AE; BLC /WDR, AE TARGET 'H'" @SEPIA CDS-R @SEPIA CDS-G "@AE; SAND&SNOW MODE AE TARGET 'L'" "@AE; SAND&SNOW MODE AE TARGET 'H'" changed by AUTO 3MLENS ADJ(0DE) changed by AUTO 3MLENS ADJ(0DE) changed by AUTO 3MLENS ADJ(0DE) changed by AUTO 3MLENS ADJ(0DE) @CCD H-PIXEL NUMBER -LOW BYTE @CCD H-PIXEL NUMBER -HIGH BYTE @CCD V LINE NUMBER -LOW BYTE @CCD V LINE NUMBER -HIGH BYTE @CCD V SKIP LINE DEFAULT VALUE @CCD V LINE NUMBER LOW BYTE @CCD V LINE NUMBER HIGH BYTE "@DSP IC ADDR #41H ;ART DSE LEVEL" "@DSP IC ADDR #1CH ;NEGA MODE WHITE CLIP LEVEL" * AWB- START HALL VALUE "@DSE- MOSAIC SIZE; DSP IC ADDR #39H " "@D/ZOOM MAX RATIO; CO=4X, EE=14.3X, F4= 20X " @ NOISE SLICE START AGC VALUE @ HAP(DSP #10BH) MIN VALUE AT AGC MAX @ VAP(DSP 310C) MIN VALUE AT AGC MAX @ YAP(DSP #10DH) MAX VALUE AT AGC MAX @ CHROMA SUPPRESS PERCENT @FOCUS TELE MARGIN LOW BYTE(CANON X22 LENS) @FOCUS TELE MARGIN HIGH BYTE(CANON X22 LENS) @FOCUS WIDE MARGIN LOW BYTE(CANON X22 LENS) @FOCUS WIDE MARGIN HIGH BYTE(CANON X22 LENS)

@@W/B AUTO ADJUST @@LENS AUTO INFINITE ZOOM TRACK(DON'T USE IN SERVICE FIELD) FIND AGC ADJUST TARGET SHUTTER CONTROL AT AGC AUTO ADJUST (ADDR.0DB) NO USED @@ZOOM VR LEVER CENTER FINDING @@ZOOM/FOCUS CHK=ONE AF ENABLE BIT 00~03 NO USED @@AGC AUTO ADJUST (ADDR. 0B0,0B1,0D1,0AC,0AD) "@LENS ZOOM TRACK CHECKING ;CONFIRM,DATA UP,DOWN KEY" NO USED "@@LENS 3M ZOOM TRACK ADJUST =SERVICE FIELD MODE (KEEP DISTANCE; 3M+/-1Cm)" @EEPROM -TABLE -INITIAL ('99'+CONFIRM =CAMERA ONLY, 'AA'+CONFIRM=CAM+VCR INITIAL) VCR ADDRESS & DATA
CAMERA ADJUST MODE, EEPROM ADDRESS SEQUENCE & DATA OF PAGE 1
ADDR MODEL/DATA PAL HI8 ADDR 10A 10B 10C 10D 10E 10F DATA 00 A0 C0D 70 0D 0D 0C A0 C0D 0D 0C A0 C0D 40 0D 0D 0C A0 C0D 0D 0C 09 NORMAL HI8 NTSC NORMAL D7 BIT SEGMENTATION EXPLAIN D6 D5 D4 VSKIP='0' SCK H2DEL(3:0) LALT D3 CINEMA ='0' HSP D2 ND TEST DOSEL D1 DSYNC H_MAX_SEL(1:0) PBLK_SEL HSSC(8) ----| ----| ----| |---|---DSCKSEL RGDLY[3:0] -8~+7nS SHD_DLY[3:0] -8~+7nS FWCKDLY[2:0] 0~+7nS ----| ----| ----| ----| ----| D0 JITNSYNC CONTENT (EEPROM DATA PAGE 1)
EMODE(2:0)='000'internal reset ADCK FWCK
SHTR='11' HSS |---|---|---|---FLALTSEL |---|---DCKSEL

0~15nSEC DELAY ADJUST

HIGH SHUTTER SPEED CONTROL (8:0) GHDLY(7:0) -128 ~+ 127 H1DLY[3:0] 0~+15nS SHP_DLY[3:0] -8~+7nS ADCKDLY[2:0] HCNTSET[7:0] LSSC[7:0] low speed shutter |---VCNTSET[6:0] 0~+7nS
* WDR-AF CLIMB NOISE THRESHOLD * WDR-AF CENTER DATA THRESHOLD LOW * WDR-AF CENTER DATA THRESHOLD HIGH * WDR-AF PEAK NOISE THRESHOLD LOW * WDR-AF PEAK NOISE THRESHOLD HIGH CLUSTER 1 (HEADER[3:0] = 4'b0001) ENCODER/ DEFECT COMPENSATION

11A 11B 11C 11D 11E 11F

D0D 00 0E 03

D0A 03

C0E 00 0A 03

CC 00 0A 03

|---|---|---FSC4 |---|---X X |----|----X |---|---X
C-SYNC[7:0] c.sync level 0~255 SETUP[7:0] setup level 0~255 EBURST[7:0] burst phase control :NTSC only EYDLY[2:0]000=-4PCK,111=+3PCK EUSC[7:0] EVSC[7:0] X X UV_CTRL |---EBURST_H[2:0]
----| ----| ----| ----| ----| ----| NOTBC S2 EXTDAC S1 PD1 S0 ----| ----| RAM-OUT |-------| RAM-OUT[8:6] RAM-OUT[9:8] ----|
"-128~+127 ;B-Y BURST VALUE" "-128~+127 ;R-Y BURST VALUE" X X X D-CLP

AD[1:0] AD CLK DLY

CLAMP_OFFSET[7:0] DEFECY_THRESHOLD[7:0] 0~255 X RAM-OUT[5:0] RAM-OUT[7:0] |---PFINDCNT[5:0] X X

7. Pre white balance (I) 1) Camera E-E, 3100K gray-scale chart. 2) Video(output) jack and AF MICOM. 3) Connect vectorscope input jack to video(output) jack. 4) Press the DATE/TIME(MODE UP)/TITLE (MODE DOWN) button so that the OSD state is 137. XX XX. (R-Y axial) 5) Aim the camera at a 3100K gray-scale chart illuminated at 1500 to 2000 lx. 6) Adjust the C/RESET(DATA UP)/Z/RTN (DATA DOWN) button so that the white vector moves to the R-Y axial on screen of the vectorscope. Note : Bright dot shifts after the confirm button is pressed.
8. Pre white balance (II) 1) Camera E-E, 3100K gray-scale chart. 2) Video(output) jack and AF MICOM. 4) Connect vectorscope input jack to video(output) jack. 3) Press the DATE/TIME (MODE UP)/TITLE (MODE DOWN) button so that the OSD state is 138. XX XX. 5) Aim the camera at a 3100K gray-scale chart illuminated at 1500 to 2000 lx. 6) Adjust the C/RESET(DATA UP)/Z/RTN (DATA DOWN) button so that the white vector moves to the B-Y axial on screen of the vectorscope. Note : Bright dot shifts after the confirm button is pressed.
10. R-Y Negative Gain 1) Camera E-E, 3100K color bar chart. 2) Video(output) jack and register of EEPROM. 3) Connect video(output) jack to waveform monitor input jack and monitor TV jack respectively. 4) Press the DATE/TIME(MODE UP)/TITLE (MODE DOWN) button so that the OSD state is 148. XX XX. 5) Aim the camera at a color bar chart illuminated at 1500 to 2000 lx. 6) Adjust the C/RESET(DATA UP)/Z/RTN (DATA DOWN) button so that the cyan level is 65IRE. 7) Be sure to press the MENU/ENTER/CONFIRM) button to memorize setting. Note : Bright dot shifts after the confirm button is pressed.
11. B-Y Positive Gain 9 R-Y Positive Gain 1) Camera E-E, 3100K color bar chart. 2) Video(output) jack and register of EEPROM. 3) Connect video(output) jack to waveform monitor input jack and monitor TV jack respectively. 4) Press the DATE/TIME(MODE UP)/TITLE (MODE DOWN) button so that the OSD state is 147. XX XX. 5) Aim the camera at a color bar chart illuminated at 1500 to 2000 lx. 6) Adjust the C/RESET(DATA UP)/Z/RTN (DATA DOWN) button so that the red level is 70IRE. 7) Be sure to press the MENU/ENTER(CONFIRM) button to memorize setting. Note : Bright dot shifts after the confirm button is pressed. 1) Camera E-E, 3100K color bar chart. 2) Video(output) jack and register of EEPROM. 3) Connect video(output) jack to waveform monitor input jack and monitor TV jack respectively. 4) Press the DATE/TIME(MODE UP)/TITLE (MODE DOWN) button so that the OSD state is 14B XX XX. 5) Aim the camera at a color bar chart illuminated at 1500 to 2000 lx. 6) Adjust the C/RESET(DATA UP)/Z/RTN (DATA DOWN) button so that the blue level is 50IRE. 7) Be sure to press the MENU/ENTER(CONFIRM) button to memorize setting. Note : Bright dot shifts after the confirm button is pressed.

2. The following chart shows the function of each button. In service adjustment mode, button names are different from those in customer camera function control mode. EX)MENU/ENTER button is the same as confirm. Button DATE/TIME (MODE UP) TITLE (MODE DOWN) C/RESET (DATA UP) Z/RTN (DATA DOWN) MENU/ENTER (CONFIRM) Function When change the adjustment mode. When change the adjustment mode. When change data value of adjust state. Data store after finishing adjustment by DATA UP/DATA DOWN button

ADDRESS A B

MODE TINT COLOR BRIGHT CONTRAST R SUB B SUB GAMMA 1 GAMMA 2 PLL MODE 1 MODE 2 MODE 3

NTSC 8A 8A 75 BF5

PAL 75 B0E 00 F5
MEAN TINT COLOR GAIN BRIGHT CONTRAST R-BRIGHT B-BRIGHT GAMMA1 GAIN GAMMA2 GAIN PLL SYSTEM SELECTION 1 SYSTEM SELECTION 2 H-POSITION
REMARK ADJUST ADJUST ADJUST FIXED ADJUST ADJUST FIXED FIXED ADJUST FIXED FIXED FIXED
NOTE : XX XX: indicates variable values.

5-2-4 (b) ADJUSTMENT

Note : 1. From this point forward, the structure of every adjustment is as follows. 2. See page 5-26 for the location of test points and adjustments.

Adjustment Item

1. Mode and input signal 2. Test point 3. Result and Remarks
1. PLL 1) Color bar 2) Connect an oscilloscope probe to PLL 3) Press the DATE/TIME(MODE UP)/TITLE (MODE DOWN) button so that the OSD state is 8 PLL EPR:XX EVR:XX 4) Adjust the C/RESET(DATA UP)/Z/RTN (DATA DOWN) button so that RPD level is DC1.8+-0.1Vp-p. 5) Be sure to press the MENU/ENTER(CONFIRM) button to memorize setting. 6) The OSD shows OK
8.0V (PEDESTAL TO PEDESTAL)
3. R-Sub Brightness 1) Color bar 2) R-OUT 3) Connect an oscilloscope probe to R-OUT. 4) Press the DATE/TIME(MODE UP)/TITLE (MODE DOWN) button so that the OSD state is 4 R SUB EPR:XX EVR:XX 5) Adjust the C/RESET(DATA UP)/Z/RTN (DATA DOWN) button so that R-OUT(Red) level is 8.0Vp-p (pedestal to pedestal). 6) Be sure to press the MENU/ENTER(CONFIRM) button to memorize setting. 7) The OSD shows O.K
2. Brightness 1) Color bar. 2) G-OUT. 3) Connect an oscilloscope probe to G-OUT. 4) Press the DATE/TIME(MODE UP)/TITLE (MODE DOWN) button so that the OSD state is 2 BRIGHT EPR:XX EVR:XX 5) Adjust the C/RESET(DATA UP)/Z/RTN (DATA DOWN) button so that bright(Green) level is 8.0Vp-p (pedestal to pedestal). 6) Be sure to press the MENU/ENTER(CONFIRM) button to memorize setting. 7) The OSD shows O.K
4. B-Sub Brightness 1) Color bar 2) B-OUT 3) Connect an oscilloscope probe to B-OUT. 4) Press the DATE/TIME(MODE UP)/TITLE (MODE DOWN) button so that the OSD state is 5 B SUB EPR:XX EVR:XX 5) Adjust the C/RESET(DATA UP)/Z/RTN (DATA DOWN) button so that B OUT(Blue) level is 8.0Vp-p (pedestal to pedestal). 6) Be sure to press the MENU/ENTER(CONFIRM) button to memorize setting. 7) The OSD shows O.K
6. TINT 1) Color bar 2) B-OUT 3) Connect an oscilloscope probe to B-OUT. 4) Press the DATE/TIME(MODE UP)/TITLE (MODE DOWN) button so that the OSD state is 0 TINT EPR:XX EVR:XX 5) Adjust the C/RESET(DATA UP)/Z/RTN (DATA DOWN) button so that the dual waveforms are superimposed. 6) Be sure to press the MENU/ENTER(CONFIRM) button to memorize setting. 7) The OSD shows O.K Note : If the data is largely changed, perform 5. Color Adjustment.

DUAL WAVEFORMS ARE SUPERIMPOSED. 8.0V (PEDESTAL TO PEDESTAL)
5. Color 1) Color bar 2) B-OUT 3) Connect an oscilloscope probe to B-OUT. 4) Press the DATE/TIME(MODE UP)/TITLE (MODE DOWN) button so that the OSD state is 01 COLOR EPR:XX EVR:XX 5) Adjust the C/RESET(DATA UP)/Z/RTN (DATA DOWN) button so that the Yellow level is equal to the pedestal line. 6) Be sure to press the MENU/ENTER(CONFIRM) button to memorize setting. 7) The OSD shows O.K.

PEDESTAL LINE

YELLOW LEVEL

NO. 5 6

Address 1 0
Adjustment PLL BRIGHTNESS R-SUB BRIGHTNESS R-SUB BRIGHTNESS COLOR TINT
Test point PLL G-OUT R-OUT B-OUT B-OUT B-OUT
Adjustment point EVR EVR EVR EVR EVR EVR
Spec. 1.80.1V DC 8.0Vp-p 8.0Vp-p 8.0Vp-p -

Test point ADJ. point

2. BRIGHTNESS

1. PLL

3. R-SUB BRIGHTNESS

ICE02 PLL

G-OUT R-OUT CNE02 CNE01 B-OUT
4. B-SUB BRIGHTNESS 5. COLOR 6. HUE
5-3 VCR Section Adjustment

5-3-1 Preparations

1. Equipment : 1) Monitor TV. 2) Dual trace oscilloscope of over 20MHz band, incorporates delay mode. (Use 10 : 1 probe unless otherwise specified.) 3) Frequency counter 4) DC power supply. 5) Alignment tape (Colour bar : SP) 6) 8mm Video Tape for record. STEP 1 1. Connect the power source (battery/DC cable). 2. Set the power switch of the camcorder to PLAYER position. 3. Press the eject key to eject mode.
2. Composition of VCR P.C.Boards 1) Main PCB (system control/servo, video, audio, camera, DC/AC CONVERTER) 2) Rear PCB 3) Function PCB 4) Front PCB
STEP 2 1. Press and hold EJECT button STOP button on the Camcorder at the same time for more than 5 seconds. 2. If the color bar generated internally appears on the monitor and adjustment mode displayed like the figure below, VCR adjustment mode has been successfully activated. 3. Insert tape into housing assy and then perform the adjustments.

TV or EVF/CVF monitor

01.CAPSTAN FG EPR:XX EVR:XX
Address of the adjustment mode. : there are 01h to 1 ch.(refer xxxx)
Name of the adjustment mode. : every address have a name like this (refer xxx) Present data : be adjusts before. New data : be adjusted newly.
3. How to get into service ADJUST mode.
4. The location of function button.

For Camcorder Adjustment

5. If you want to finish the adjustment mode, you have to do Battery Reset. The Battery Reset means that you pull out the power source and pull in it again. Then, the adjustment ended and the camcorder works normally.

5-3-2 VCR Section

Note 1 : From this point forward, the structure of every adjustment is as follows. Step Adjustment Item
1. Mode and input signal/ alignment tape 2. Test point and ADJ. part 3. Result and Remarks

2-2. Head Switching Point 2-3. Adjusting Color Bar Level : This adjustment is performed after the replacement of deck mechanism. Without this adjustment, there will be a noise in playback picture. a. Preparations
STANDARD COLOR BAR TAPE RECORDED WITH SP SPEED
: This adjustment is performed to set the standard level of color bar signal which is generated internally. a. Preparations
TAPE EQUIPMENT OTHER TEST POINT NONE OSCILLOSCOPE NONE IC201 PIN 24 1C COLOR BAR LEVEL
EQUIPMENT OTHER TEST POINT ADDRESS NAME
POWER SOURCE NONE NONE 0A HD SWP

ADDRESS NAME

b. Connect a power source. c. Get into the VCR adjustment mode. d. Press the DATE/TIME(MODE UP)/TITLE (MODE DOWN) button of CAMCORDER so as to select the address 0A. e. Insert the Standard Color Bar Tape and press the PLAY button.
b. Connect a power source. c. Get into the VCR adjustment mode. d. Press the DATE/TIME(MODE UP)/TITLE (MODE DOWN) button of CAMCORDER so as to select the address 1C. e. Connect the oscilloscope to the addressed Test Point. f. Press the C/RESET(DATA UP)/Z/RTN(DATA DOWN) button so as to set the P-P level of composite to 0.5V0.02Vp-p. Note : The level is changed after the confirmation.
e. Insert a Normal Tape to the camcorder. f. Connect the oscilloscope to the addressed Test Point. g. Press the C/RESET(DATA UP)/Z/RTN(DATA DOWN) button so that the IC201 PIN13 is 0.50.02Vp-p from SYNC tip to peak level.

0.5 0.02Vp-p

WHITE ( APPROX. 100% ) APPROX. 0.7V APPROX. 0.3V H
h. Be sure to press the MENU/ENTER(CONFIRM) button of CAMCORDER to memorize setting. i. Reset the power source so as to fix the new data to the EEPROM.
2-5. Adjusting PB OUT LEVEL : This adjustment is perform to set the video out level to the regulated level. a. Preparations
g. Be sure to press the MENU/ENTER(CONFIRM) button of CAMCORDER to memorize setting. h. Reset the power source so as to fix the new data to the EEPROM.
2-4. Adjusting Y-Emphasis Input : This adjustment is performed to set the Y level which is recorded in tape. Maladjusted Y level impact to the next adjustment. a. Preparations
TAPE EQUIPMENT OTHER TEST POINT ADDRESS NAME IC 201 PIN Y-EMPHASIS IN (NOR) 8MM (NORMAL) TAPE OSCILLOSCOPE EQUIPMENT OTHER TEST POINT ADDRESS NAME OSCILLOSCOPE CONNECT THE MONITOR (75) CN605 PINPB OUT-LEVEL (NOR)
b. Connect a power source. c. Get into the VCR adjustment mode. d. Press the DATE/TIME(MODE UP)/TITLE (MODE DOWN) button of CAMCORDER so as to select the address 03. e. Insert the Standard Color Bar Tape and press the PLAY button. f. Connect the oscilloscope to the addressed Test Point.
b. Connect a power source. c. Get into the VCR adjustment mode. d. Press the DATE/TIME(MODE UP)/TITLE (MODE DOWN) button of CAMCORDER so as to select the address 02.

Remark ALL ALL ALL ALL ALL SCA30/SCA33/SCA80/VP-A30 VP-A31/VP-A33/VP-A800 SCA35/SCA85/VP-A34/VP-A850 ALL ALL ALL ALL ALL ALL ALL ALL SCA30/SCA33/SCA80/VP-A30 VP-A31/VP-A33/VP-A800 ALL ALL ALL ALL ALL ALL ALL ALL ALL SCA80/VP-A800 VP-A34/SCA35 VP-A850/SCA85 SCA30/SCA33/VP-A30/VP-A31 VP-A33 SCA30/SCA33/SCA80/VP-A30 VP-A31/VP-A33/VP-A800 SCA35/SCA85/VP-A34/VP-A850 SCA30/SCA33/SCA80/VP-A30 VP-A31/VP-A33/VP-A800 SCA35/SCA85/VP-A34/VP-A850 SCA30/SCA33/SCA80/VP-A30 VP-A31/VP-A33/VP-A800 SCA35/SCA85/VP-A34/VP-A850 ALL ALL ALL ALL ALL ALL ALL

910 914

AD90-10841K ASSY-REAR BOARD;VP-L300/XEU,S8C-PAL LCD AD90-10852M ASSY-REAR BOARD;VP-L350/XEU,LIGHT,S8C-PA AD98-12026Z ASSY-CASE-REAR;VP-A30,LIGHT(X) AD98-12029Z AD98-12027F AD98-12029Y AD60-10543A AC60-10020A AC60-10055A AC60-10024A AD60-10001A AD60-10510A AD60-00003A ASSY-CASE REAR;VP-A850,LIGHT(O) ASSY-CASE RIGHT;SC-L300,ASSY-CASE RIGHT;SV-L350,NTSC,SCREW-MACHINE;-,BH,+,-,M2,9,BLK,-,BLK SCREW-MACHINE;BH,+,M2,X5,FZB,FE,UP,-,SCREW-TAPPING;BH,+,-,M2,X4,FZB SCREW-MACHINE;BH,+,M2,X3,FZW,FE,-,-,SCREW-MACHINE;BH,B,1.7*5.5,-,FE,BLACK,-, SCREW-MACHINE;-,PLAN,+,-,M1.4X5,5,BLK,FE SCREW-TAPTITE;-,+,-,H8.5,2X6,-
6-5 EVF (SCA30/VP-A30/VP-A31/VP-A34/VP-A800/VP-A850)

407 408

906 306

417 418

Loc. No New Part No 905 906
Remark SCA30/VP-A30/VP-A31/VP-A34 VP-A800/VP-A850 SCA30/VP-A30/VP-A31/VP-A34 VP-A800/VP-A850 SCA30/VP-A30/VP-A31/VP-A34 VP-A800/VP-A850 SCA30/VP-A30/VP-A31/VP-A34 VP-A800/VP-A850 SCA30 VP-A30/VP-A31/VP-A34/VP-A800 VP-A850 SCA30/VP-A30/VP-A31/VP-A34 VP-A800/VP-A850 SCA30/VP-A30/VP-A31/VP-A34 VP-A800/VP-A850 SCA30/VP-A30/VP-A31/VP-A34 VP-A800/VP-A850 SCA30/VP-A30/VP-A31/VP-A34 VP-A800/VP-A850 SCA30/VP-A30/VP-A31/VP-A34 VP-A800/VP-A850 SCA30/VP-A30/VP-A31/VP-A34 VP-A800/VP-A850 SCA30/VP-A30/VP-A31/VP-A34 VP-A800/VP-A850 SCA30/VP-A30/VP-A31/VP-A34 VP-A800/VP-A850 SCA30/VP-A30/VP-A31/VP-A34 VP-A800/VP-A850 SCA30/VP-A30/VP-A31/VP-A34 VP-A800/VP-A850 SCA30/VP-A30/VP-A31/VP-A34 VP-A800/VP-A850 SCA30/VP-A30/VP-A31/VP-A34 VP-A800/VP-A850 SCA30 VP-A30/VP-A31/VP-A34/VP-A800 VP-A850 SCA30/VP-A30/VP-A31/VP-A34 VP-A800/VP-A850 SCA30/VP-A30/VP-A31/VP-A34 VP-A800/VP-A850 SCA30/VP-A30/VP-A31/VP-A34 VP-A800/VP-A850 SCA30/VP-A30/VP-A31/VP-A34 VP-A800/VP-A850
AC90-10012V ASSY-CRT;CS96(SPORTS),AD98-11265G ASSY-EVF LENS;A3-PJ,B/W AC67-12070A LENS-EVF(MD);PMMA D19.1 ASP,-,-,-,-,AD61-22029A HOLDER-LENS A;-,ABS94,HB,BLK,-,AD90-10850M ASSY-EVF BOARD;SC-L350,NTSC -A3/S3/CS99 AD90-10850N ASSY-EVF BOARD;VP-L350,PAL-A3/S3/CS99 AC67-10066A LENS-EVF GJ;-,OPT,GRASS-F1,D11.5,-,CG819 AD61-21142A HOLDER-LENS B;-,ABS94,HB,BLK,-,-

CE45 CE46 CE50 CE51
PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC
RE24 RE25 RE26 RE27 RE28 RE29 RE30 RE31 RE32 RE34 RE40 RE44 RE45 RE47 RE50 RE51 RE57 RE58 RE61 RE62 RE63 XE01 XE01
PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC NTSC
2203-000189 C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, 2404-000139 C-TA,CHIP;10uF,20%,6.3V,-,3216,-,TP 2404-000139 C-TA,CHIP;10uF,20%,6.3V,-,3216,-,TP 2203-000189 C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP,
2007-000084 R-CHIP;4.7Kohm,5%,1/16W,DA,TP,1608 2007-000455 R-CHIP;18Kohm,1%,1/16W,DA,TP,1608 2007-000614 R-CHIP;24Kohm,1%,1/16W,DA,TP,1608 2007-000683 R-CHIP;3.3Kohm,1%,1/16W,DA,TP,1608 2007-000067 R-CHIP;15Kohm,1%,1/16W,DA,TP,1608 2007-000078 R-CHIP;1Kohm,5%,1/16W,DA,TP,1608 2007-000124 R-CHIP;2.2Kohm,5%,1/16W,DA,TP,1608 2007-000124 R-CHIP;2.2Kohm,5%,1/16W,DA,TP,1608 2007-000090 R-CHIP;10Kohm,5%,1/16W,DA,TP,1608 2007-000078 R-CHIP;1Kohm,5%,1/16W,DA,TP,1608 2007-000102 R-CHIP;100Kohm,5%,1/16W,DA,TP,1608 2007-000309 R-CHIP;10ohm,5%,1/16W,DA,TP,1608 2007-000075 R-CHIP;220ohm,5%,1/16W,DA,TP,1608 2007-000075 R-CHIP;220ohm,5%,1/16W,DA,TP,1608 2203-000426 C-CERAMIC,CHIP;18pF,5%,50V,NPO,1608,-,TP 2007-000123 R-CHIP;1.5Kohm,5%,1/16W,DA,TP,1608 2007-000079 R-CHIP;1.8Kohm,5%,1/16W,DA,TP,1608 2007-000087 R-CHIP;6.8Kohm,5%,1/16W,DA,TP,1608 2007-000078 R-CHIP;1Kohm,5%,1/16W,DA,TP,1608 2007-000078 R-CHIP;1Kohm,5%,1/16W,DA,TP,1608 2007-000070 R-CHIP;0ohm,5%,1/16W,DA,TP,1608 2801-003126 CRYSTAL-SMD;4.433619MHz,30ppm,28-ABN,16p 2801-003127 CRYSTAL-SMD;3.579545MHz,30ppm,28-ABN,16p ASS'Y-CCD BOARD
CNE01 3711-000386 CONNECTOR-HEADER;3WALL,10P,1R,1.25mm,SMD PAL/NTSC CNE01 3711-002172 CONNECTOR-HEADER;BOX,3P,1R,1.5,STRAIGHT, CNE02 3708-000514 CONNECTOR-FPC/FC/PIC;16P,0.5MM,SMD-S,SN NTSC PAL/NTSC
CNE03 3711-002613 CONNECTOR-HEADER;3WALL,3P,1R,1.25MM,SMD- PAL/NTSC DE01 DE02 DE03 DE04 DE05 0405-000123 DIODE-VARACTOR;1T369,34V,10nA,DSM,TP 0401-001054 DIODE-SWITCHING;KDS160,85V,300mA,SOD-323 0401-001054 DIODE-SWITCHING;KDS160,85V,300mA,SOD-323 0401-001054 DIODE-SWITCHING;KDS160,85V,300mA,SOD-323 0401-001054 DIODE-SWITCHING;KDS160,85V,300mA,SOD-323 PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC NTSC PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC NTSC PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC NTSC PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC PAL/NTSC

2203-001686 C-CERAMIC,CHIP;75pF,5%,50V,CH,TP,1608,1. 2203-000357 C-CERAMIC,CHIP;150pF,5%,50V,NPO,TP,1608, 2203-000236 C-CERAMIC,CHIP;100pF,5%,50V,NPO,TP,1608, 2203-000189 C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, 2203-000332 C-CERAMIC,CHIP;12pF,5%,50V,NPO,TP,1608,2203-000384 C-CERAMIC,CHIP;15pF,5%,50V,NPO,TP,1608,2203-001408 C-CERAMIC,CHIP;270pF,5%,50V,COG,TP,1608, 2203-000257 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608, 2203-000257 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608, 2203-000925 C-CERAMIC,CHIP;470nF,+80-20%,50V,Y5V,TP, 2203-000257 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608, 2203-000189 C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, 2203-000426 C-CERAMIC,CHIP;18pF,5%,50V,NPO,1608,-,TP 2203-000426 C-CERAMIC,CHIP;18pF,5%,50V,NPO,1608,-,TP 2203-000257 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608, 2203-000257 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608, 2203-000257 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608, 2203-000257 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608, 2203-000384 C-CERAMIC,CHIP;15pF,5%,50V,NPO,TP,1608,2404-000139 C-TA,CHIP;10uF,20%,6.3V,-,3216,-,TP 2203-000384 C-CERAMIC,CHIP;15pF,5%,50V,NPO,TP,1608,2203-000257 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608, 2203-000257 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608, 2203-000315 C-CERAMIC,CHIP;120pF,5%,50V,NPO,TP,1608, 2203-000257 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608, 2203-000851 C-CERAMIC,CHIP;39pF,5%,50V,NPO,TP,1608,2203-000257 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608, 2203-000426 C-CERAMIC,CHIP;18pF,5%,50V,NPO,1608,-,TP 2203-000257 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608, 2203-000384 C-CERAMIC,CHIP;15pF,5%,50V,NPO,TP,1608,2404-000139 C-TA,CHIP;10uF,20%,6.3V,-,3216,-,TP 2203-000626 C-CERAMIC,CHIP;22pF,5%,50V,NPO,TP,1608,2203-000257 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608, 2203-000189 C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, 2203-001195 C-CERAMIC,CHIP;7pF,0.25pF,50V,NPO,TP,160 2203-002605 C-CERAMIC,CHIP;8pF,0.25pF,50V,CH,TP,1608 2203-000426 C-CERAMIC,CHIP;18pF,5%,50V,NPO,1608,-,TP 2203-000384 C-CERAMIC,CHIP;15pF,5%,50V,NPO,TP,1608,2203-000257 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608, 2203-001640 C-CERAMIC,CHIP;390pF,10%,50V,X7R,TP,1608 2203-001083 C-CERAMIC,CHIP;5pF,0.1pF,50V,NPO,TP,1608 2203-000257 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608, 2203-000257 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608, 2404-000139 C-TA,CHIP;10uF,20%,6.3V,-,3216,-,TP 2203-000257 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608, 2203-000815 C-CERAMIC,CHIP;33pF,5%,50V,NPO,TP,1608,2203-000315 C-CERAMIC,CHIP;120pF,5%,50V,NPO,TP,1608, 2203-000998 C-CERAMIC,CHIP;47pF,5%,50V,NPO,TP,1608,2203-000626 C-CERAMIC,CHIP;22pF,5%,50V,NPO,TP,1608,2203-000257 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608, Hi8 NORMAL NORMAL/PAL NORMAL/NTSC
C061 C1 C10 C10 C101 C102 C103 C104 C105 C106 C107 C108 C109 C11 C110 C111 C112 C113 C114 C115 C116 C117 C118 C119 C12 C120 C121 C122 C123 C124 C125 C126 C127 C128 C129 C13 C130 C131 C132 C133 C134 C135 C136 C137

2203-000715 C-CERAMIC,CHIP;3.3nF,10%,50V,X7R,TP,1608 2203-001607 C-CERAMIC,CHIP;220pF,5%,50V,CH,TP,1608,1 2203-001656 C-CERAMIC,CHIP;470pF,5%,50V,CH,TP,1608,1 2203-000189 C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, 2203-001640 C-CERAMIC,CHIP;390pF,10%,50V,X7R,TP,1608 2203-001640 C-CERAMIC,CHIP;390pF,10%,50V,X7R,TP,1608 2203-000257 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608, 2203-000357 C-CERAMIC,CHIP;150pF,5%,50V,NPO,TP,1608, 2203-000257 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608, 2203-000357 C-CERAMIC,CHIP;150pF,5%,50V,NPO,TP,1608, 2203-000929 C-CERAMIC,CHIP;470pF,10%,50V,X7R,TP,1608 2203-001607 C-CERAMIC,CHIP;220pF,5%,50V,CH,TP,1608,1 2203-002793 C-CERAMIC,CHIP;1uF,+80-20%,25V,Y5V,TP,20 2404-000139 C-TA,CHIP;10uF,20%,6.3V,-,3216,-,TP 2203-000257 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608, 2203-000257 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608, 2203-000315 C-CERAMIC,CHIP;120pF,5%,50V,NPO,TP,1608, 2203-000357 C-CERAMIC,CHIP;150pF,5%,50V,NPO,TP,1608, 2203-001607 C-CERAMIC,CHIP;220pF,5%,50V,CH,TP,1608,1 2203-000925 C-CERAMIC,CHIP;470nF,+80-20%,50V,Y5V,TP, 2203-000257 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608, 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608 2404-000151 C-TA,CHIP;1uF,20%,16V,-,TP,3216,2203-001683 C-CERAMIC,CHIP;68pF,5%,50V,CH,TP,1608,1. 2203-000315 C-CERAMIC,CHIP;120pF,5%,50V,NPO,TP,1608, 2404-000250 C-TA,CHIP;470nF,20%,25V,-,TP,3216,2203-000257 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608, 2203-000925 C-CERAMIC,CHIP;470nF,+80-20%,50V,Y5V,TP, 2404-000304 C-TA,CHIP;22uF,20%,6.3V,-,TP,3528,2203-000189 C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, 2203-000257 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608, 2203-000925 C-CERAMIC,CHIP;470nF,+80-20%,50V,Y5V,TP, 2404-000139 C-TA,CHIP;10uF,20%,6.3V,-,3216,-,TP 2203-000925 C-CERAMIC,CHIP;470nF,+80-20%,50V,Y5V,TP, 2203-000257 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608, 2203-000925 C-CERAMIC,CHIP;470nF,+80-20%,50V,Y5V,TP, 2203-000257 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608, 2203-000257 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608, 2203-000257 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608, 2203-000236 C-CERAMIC,CHIP;100pF,5%,50V,NPO,TP,1608, 2203-001408 C-CERAMIC,CHIP;270pF,5%,50V,COG,TP,1608, 2203-000257 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608, 2404-000139 C-TA,CHIP;10uF,20%,6.3V,-,3216,-,TP 2404-000139 C-TA,CHIP;10uF,20%,6.3V,-,3216,-,TP 2203-002793 C-CERAMIC,CHIP;1uF,+80-20%,25V,Y5V,TP,20 2203-000405 C-CERAMIC,CHIP;180pF,5%,50V,NPO,TP,1608, 2203-000257 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608, 2203-001113 C-CERAMIC,CHIP;62pF,5%,50V,NPO,TP,1608,2203-000815 C-CERAMIC,CHIP;33pF,5%,50V,NPO,TP,1608,2404-000218 C-TA,CHIP;330nF,20%,35V,-,TP,3216,Hi8 NORMAL Hi8 NORMAL NORMAL Hi8 NORMAL Hi8
C270 C271 C272 C273 C28 C281 C282 C283 C29 C292 C293 C3
C30 C30 C31 C311 C312 C313 C314 C315 C32 C33 C331 C331 C34 C35 C355 C36 C37 C38 C39 C4 C40 C401 C401 C41 C42 C43 C44 C45 C451 C452 C453 C454 C46 C47 C48 C49 C5 C50 C501 C502 C503 C505 C506 C507 C508 C509 C510 C511 C512 C513

2203-000440 C-CERAMIC,CHIP;1nF,10%,50V,X7R,TP,1608,2203-000189 C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, 2203-000440 C-CERAMIC,CHIP;1nF,10%,50V,X7R,TP,1608,2203-000440 C-CERAMIC,CHIP;1nF,10%,50V,X7R,TP,1608,2404-000284 C-TA,CHIP;10uF,20%,16V,-,TP,3528,2203-000236 C-CERAMIC,CHIP;100pF,5%,50V,NPO,TP,1608, 2203-000236 C-CERAMIC,CHIP;100pF,5%,50V,NPO,TP,1608, 2203-000236 C-CERAMIC,CHIP;100pF,5%,50V,NPO,TP,1608,
CN001 3708-001345 CONNECTOR-FPC/FC/PIC;11P,-,SMD-A,SN CN501 3710-001301 CONNECTOR-SOCKET;48P,2R,0.8mm,SMD-S,SN CN601 3710-000551 CONNECTOR-SOCKET;24P,2R,1.0MM,SMD-S,SN CN603 3711-000386 CONNECTOR-HEADER;3WALL,10P,1R,1.25mm,SMD CN604 3708-000457 CONNECTOR-FPC/FC/PIC;15P,1.25mm,SMD-S,SN CN605 3710-001479 CONNECTOR-SOCKET;14P,2R,1MM,SMD-S,SN CN801 3708-001025 CONNECTOR-FPC/FC/PIC;30P,0.5mm,ANGLE,SN CN802 3711-000556 CONNECTOR-HEADER;BOX,12P,1R,1.25mm,SMD-A CN851 3711-002127 CONNECTOR-HEADER;BOX,8P,1R,1.25mm,SMD-A, CNP01 3710-001478 CONNECTOR-SOCKET;18P,2R,1MM,SMD-S,SN CNP02 3708-001070 CONNECTOR-FPC/FC/PIC;22P,0.5MM,SMD-A,SN CNP03 3708-001069 CONNECTOR-FPC/FC/PIC;20P,0.5MM,SMD-A,SN CP01 CP02 CP03 CP04 CP05 CP06 CP07 CP08 CP09 CP10 2404-000156 C-TA,CHIP;1uF,20%,35V,-,TP,3528,1.4mm 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608 2203-000357 C-CERAMIC,CHIP;150pF,5%,50V,NPO,TP,1608, 2203-000604 C-CERAMIC,CHIP;22nF,10%,25V,X7R,TP,1608, 2203-000189 C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, 2203-000715 C-CERAMIC,CHIP;3.3nF,10%,50V,X7R,TP,1608 2203-001634 C-CERAMIC,CHIP;33nF,10%,50V,X7R,TP,1608, 2203-000604 C-CERAMIC,CHIP;22nF,10%,25V,X7R,TP,1608, 2203-000189 C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, 2404-000139 C-TA,CHIP;10uF,20%,6.3V,-,3216,-,TP
CP100 2203-000189 C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, CP101 2203-000426 C-CERAMIC,CHIP;18pF,5%,50V,NPO,1608,-,TP CP101 2203-000681 C-CERAMIC,CHIP;27pF,5%,50V,NPO,1608,-,TP CP102 2203-000257 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608, CP104 2404-000139 C-TA,CHIP;10uF,20%,6.3V,-,3216,-,TP CP105 2404-000139 C-TA,CHIP;10uF,20%,6.3V,-,3216,-,TP CP11 2203-000189 C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, PAL NTSC
CP110 2203-000189 C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, CP111 2203-000189 C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, CP12 2404-000139 C-TA,CHIP;10uF,20%,6.3V,-,3216,-,TP
CP129 2203-000626 C-CERAMIC,CHIP;22pF,5%,50V,NPO,TP,1608,CP13 CP14 CP15 CP16 CP17 CP18 CP19 CP20 CP21 2203-000236 C-CERAMIC,CHIP;100pF,5%,50V,NPO,TP,1608, 2203-000257 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608, 2203-000626 C-CERAMIC,CHIP;22pF,5%,50V,NPO,TP,1608,2203-000189 C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, 2404-000190 C-TA,CHIP;22uF,20%,16V,-,TP,5832,2203-000189 C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, 2203-000189 C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, 2203-000189 C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, 2203-000189 C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP,

10-2 10-3 10-4 10-5 10-6 10-7 10-8 10-9 10-10 10-12 10-12 10-13 10-14 10-15 10-16
For schematic Diagram - Resistors are in ohms, 1/8W unless otherwise noted. - Circled numbers refer to waveforms. Special note : Most semiconductor devices are electrostatically sensitive and therefore require the special handling techniques described under the electrostatically sensitive (ES) devices section of this service manual. Note : Do not use the part number shown on this drawing for ordering. The correct part number is shown in the parts list (may be slightly different or amended since this drawing was prepared). Important safety notices : Components identified with the mark components. Use only the same type.
have the special characteristics for safety. When replacing any of these

Schematic Diagrams

10-1 DC/DC Converter (Main)
10-2 System Control/Servo (Main)
10-3 Video (Normal) (Main)

10-4 Video (Hi-8) (Main)

10-5 Audio (Mono) (Main)
10-6 Audio (Stereo) (Main)

10-7 Camera (Main)

10-8 Rear

10-9 CCD

10-10 CVF

10-11 EVF

10-12 Front with EIS
10-13 Front without EIS (Mono)
10-14 Front without EIS (Stereo)

10-15 FUNCTION