4.7K R15

Ag_B Ag_A

Signal_B

TNY266P

IC3 R28 47

R17 10K

IC1 KA2904

C1 100nF

100 R20 PC5 LTV817B

VCC OA 2

4.7K R31

+IB -IB

4.7K R30 CE8 10uF

GND +IA

R7 CE11 1uF 1K

R16 4.7K 4.7K R13

R12 4.7K TR5 TR6

4.7K R14

10-2. PCB CIRCUIT DIAGRAM (AG-KIT)

ZD2 1N4751

C7 100nF

R27 27

CN2 SMWB250-09WHT

R3 4.7K

R24 20K

Signal_B Signal_A

PC4 LTV817B

IH 4 1

IC2 LM393

R38 1K

2. THE FEATURE OF PRODUCT

2-1. SPECIFICATIONS

WASH TYPE DIMENSION WATER PRESSURE WEIGHT WASH and SPIN CAPACITY POWER CONSUMPTION WASHING WASHING and HEATING SPIN MODEL 220~240V NET GROSS 220 V 240 V 220 V 240 V WF-F125NC 500W 34 W 43(STANDARD COURSE) MODEL rpm PAPER PLASTIC

Worktop

FRONT LOADING TYPE NET GROSS W 598mm X D 404mm X H 844mm W 668mm X D 530mm X H 890mm 50 kPa ~ 800 kPa 65 kg 68 kg 4.5 kg (DRY LAUNDRY) 180 W 180 W 2000 W 2400 W WF-F105NV 500 W
PUMPING WATER CONSUMPTION SPIN REVOLUTION PACKAGE Wt
WF-F125NC 1200 2.5kg 1.0kg

WF-F105NV 1000

Detergent drawer Control panel

Detergent drawer Door

Drain Hose
Base cover Adjustable feet tube Filter-cover Emergency drain Filter-cover Debris filter
2-2. OVERVIEW OF THE WASHING MACHINE
2-3. THE COMPARATIVE SPECIFICATIONS OF PRODUCT

Item Model Name

4.5kg WF-F125NC

Old (6.0kg) WF-F125AC

Capacity (Washing) Drum Capacity Washing Motor Heater (220V)

4.5kg 43 HXGM4I 2000W

Supply/Drain
All temperatures /Drain pump

Balancer SIZE(W*D*H)

Weight 598*404*844

Model Name

WF-F125NC

WF-F105NV

Function

Water-level Control

Add Laundry
Exterior Replacement Part Name

Specifications

Cover Door Design Handle Door

Chrome-Plating

Imperial-Silver

3. PRODUCT SPECIFICATIONS
3-1. OVERVIEW OF THE CONTROL PANEL
1. Deterg ent disp enser 2. Disp lay panel
Displays the remaining wash cycle time and error messages.
3. Silver Nano selection button
Silver Nano water is supplied in washing as well as the last rinse, featuring sterilization and antibacterial coating.
4. Rinse selection button
Press the rinse button to add rinse cycles. Maximum number of rinse cycles is five.

5. Spin selection button

Press the button repeatedly to cycle through the available spin speed options. WF-F125NC WF-F105NV No spin The laundry remains in the drum without being spun after the final drain Rinse Hold The laundry remains soaking in the final rinse water. Before the laundry can be unloaded, either Drain or the Spin program must be run. , , , 400, 800, 1000, 1200 rpm , 400, 600, 800, 1000 rpm : no spin, : rinse hold
6. Temperature selection button
Press the button repeatedly to cycle through the available water temperature options (cold water( ), 30 C, 40 C , 60 C and 95 C).
7. Delay Start selection button
Press the button repeatedly to cycle through the available delayed start options (from 3 hour to 24 hours in one hour increments). Displayed hours means the time of finished washing-cycle.

8. Fuzzy Control dial

Turn the dial to select one of the 14 available wash programs. Cotton, Coloureds, Synthetics, Delicates, Wool, Hand wash, Quick, Rinse+Spin, Spin, Drain, Baby Program(Stains, Delicates, Coloreds, Cotton)
9. Start/Pause selection button
Press to pause and restart programs.
(On/Off) selection button
Press once to turn the washing machine on, press again to turn the washing machine off. If the washing machine power is left on for longer than 10 minutes without any b uttons being touched, the power automatically turns off.
11. Wash selection button
Press the button to select wash. Wash is available only with Baby Cotton, Heavy Soil, Mixed Load, Calm Wash, Cotton, Coloureds, Synthetics, Delicates.

3-2. PROGRAMME CHART

3-3. MAIN FUNCTION
1) Auto power S/W off function After power on, the auto power S/W off function automatically switches power off for you if you do not press selection button for 10 minutes After selecting the function, the auto power S/W off function automatically switches power off for you if you do not press start/pause button for 10 minutes until 5 minutes past, After finishing the last function, the auto power S/W off function automatically switches power off for you if you do not re-select the course button or manual button 2) Door open function Door just can be opened at water level 24.80 KHz over, water temperature 55 below, motor off, if

power is off door is not opened (only auto-door model)
If door is open during the operating, all operating is halted, and door error message will be displayed (2-digit panel displays "dE" 4-digit panel displays "door") and error melody will coming out Door open error can be cleared by closing the door. the operating keeps going on 3) Rinse hold function If rinse hold function selected, the operating is finished , the machine do not drain the water after last rinse 4) No spin function If no spin function selected, the operating is finished after last rinse 5) Drain function Drain function is over, after pumping out the water for 2 minutes , without motor rotating 6) Pre-washing function Pre-washing function can be selected ,when you choice the following mode; cotton, coloreds, synthetics, delicates, baby cotton, baby coloreds, baby delicates, baby stains Water level/reverse time is the same with the selected course Pre-washing takes about 16 minutes 7) Rinse+ function This function practises rinse process once more
8) Power-out compensation function If power is out on selected process, the process before power out is stored to EEPROM, once power is back the process before power out continues. When power is back, washing process starts from the process at the point of the power out, rinse/drain process starts from the initial process. POWER-OUT COMPENSATION FUNCTION PROCESS

WASHING

RINSE/DRAIN START

RINSE/DRAIN PROCESS

FINISH
POWER OUT SAVE DATA SAVE DATA to EEPROM POWER BACK to EEPROM

POWER OUT

POWER BACK
MICOM RESTORE READ DATA (PROCESS+TIME) RESTART PROCESS

MICOM RESTORE

9) Water heater Error function This function starts working, when the heater works abnormally. (this function begins sensing the heater 2 minutes later, after the heater operating) The value of the initial thermistor(A1) is compared with that of the thermistor(A2) in 2 minutes (Y=A2-A1) - For 10 minute late, the variance of temperature(Y) is less than 2, "HE2"message is displayed on the panel. The value of the initial thermistor(A1) is compared with that of the thermistor(A2) in 11 minutes (Y=A2-A1) - For 1 minute the variance of temperature(Y) increases more than 40, "HE1"message is displayed on the panel. At this time heater, Error "HE2 (heater do not work), HE(overheated)" is displayed and all working process off The heater operating continues during heating hours, if washing hour is left over, the residual washing process keeps going without heating.
10) Fuzzy washing function (weight-sensing) After finishing initial water supply, when the fall of the water level needs supplementary water supply, Sensing function perceives the weight with the supplementary water supply numbers and starts to work. Under the course of Cotton, or Coloureds, if the supplementary water supply numbers become over 2 times the function is going at default condition ( high water level ), if 1 time that is going at middle level, if 0 below low water level, heating hours and rinse hours depend on the above data. ECO PRE mode is selected, the process going on at default condition. Washing hours Cotton High Middle Low Default Default-20 min Default-30 min Coloureds Default Default-10min Default-15min Rinse water level Default 23.80KHZ 24.10KHZ

After sensing weight, above hours is decreased from above default hours 11) Bubble - detecting function At the each condition of washing&dehydrating , rinse&dehydrating , hydrating, bubble -detecting function works, this function works 5times normally, if the function detects bubbles at 6 times , the bubble-detecting function stops and go on to the next process. The bubble-detecting function during washing & dehydrating to rinse & dehydrating after 2 times instant dehydrating and before main dehydrating, if the water level is under 24.50KHZ, Bubble Detecting function thinks there are bubbles and add the bubbles-removing rinse, needing hours are above hours and 8 Min 40 sec. The bubble-detecting function during single hydrating process after 2 times instant dehydrating and before main dehydrating , if the water level is 24.50KHZ below or during main dehydrating, water level data is 24.50KHZ below Bubble-detecting function thinks there are bubbles and add the bubbles-removing rinse 1 times, needing hours are above hours and 5 min 50 sec.
Bubble-detecting function operating process

500rpm

220rpm
18 sec laundry scattering
draining &reverse 50 sec
unbalance detecting range
bubble detection (default water level 24.50KHZ below)
12) Unbalance detecting & laundry balance positioning system Just before the hydrating process and just after reversal rotation for balancing laundry position, this function is carried out The initial 6 sec is the period of reversal rotation for balancing laundry position , Drum rotates 50rpm for initial 6 sec Next 12 sec, the rotation increases the speed from 50 rpm to 95 rpm slowly During the next 8 sec, drum rotates at the speed of 95 rpm, the sensor decides the degree of laundry unbalance with TACHO data which is attached to motor If the degree of unbalanced laundry is over 6 times to default value, laundry balancing system carryies out feed back process 3 times
Unba lanc e detectin g & laund ry balanc e pos itio nin g system

490rpm 500rpm

210rpm
20 sec laundry scattering
13) R.P.M control The rotating motor enables the magnetics( i.e generator) to generate magnetic flux in proportion to r.p.m, magnetic flux induced by coil sensor in the opposite side produces the wave like the figure below to d/dt and via rectangular wave generating circuit, the waves reaches MICOM and micom controls r.p.m with the pulse, count and cycle inputted by program.
<COIL electrical wave at both ends>

V (VOLT)

T (HOUR)

3-4. TECHNICAL POINT

1) Motor on/off time at each course

unit:sec

Washing Cw Off Ccw Off

Course

3-5. DESIGNATION OF MAIN COMPONENTS 3-5-1. Normal / Reverse Revolution of Motor and R. P. M. Control

HIGH-SPEED TACHO

MIDDLE-SPEED

Stator coil

PROTECTOR (150 C)

STATOR

5 WASHING MOTOR

<Figure1>

<Figure2>
STATOR(5.1) STATOR(5.1) ROTOR(8.9)
TACHO(3.4) PROTECTOR(6.7) "H"(mm)

Code-No.

Remark

Resistance value

WF-F125NC, WF-F105NV, WF-F1254, WF-F1054S, WF-F1054, DC31-00002H WF-F854S,WF-F854, WF-S1054, WF-S854S, WF-S854

Rated value

220~240V/50Hz
3-5-2. Door safety Device
When Door is closed, door stay closed. if "set" is operated, power supplied to ,wires have bimetal keep the door closed, and electronical power flows between and make it operate.

DC64-00653A (ROLD) 19

3-5-3. Heater
1) Capacity : AC 230V/2000W 2) Location : Bottom of TUB 3) Function : Raise the water temperature supplied at the wash process. 4) Resistance value : 23~29 5) Thermal Fuse : 128C

Thermistor

3-5-4. Detergent tub and water supply value
A Detergent tub is composed of housing and 3 drawers. supplied water flows into the 3 drawer-detergent tub by way of classifier at each washing process. three open drainage way with detergent and supplied water by way of connector located under the housing flows into washing tub. the water supply valve is composed of a hot water valve(1 way) and a cold water valve(2way) and water flow per Min in the valve is below.
Hot water valve(1 way) water flow(L/min) resistance value power consumption usable water pressure

Cold water valve (2 way)

V4.2 0.5 ~ 8 /

10 4.4

AC 220v ~ 240V 50/60
3-5-5. Shock absorber and buffer spring
This wash machine is equipped with 2 Shock absorbers with same capacity and with 2 buffer springs. 2 Shock absorber are placed under the tub and outside case , 2 buffer springs are placed on the right and left of the upper side of outside case. Shock absorber function: during wash, dehydration absorb the shock. buffer spring: buffering the vibration

device Shock absorber

capacity of Shock absorber 82 kg

3-5-6. Assy-tub Back

INNER-BEARING OUT-BEARING

OIL-SEAL

(unit : mm)
TYPE INNER-BEARING(A) OUT-BEARING(B) OIL-SEAL(C) Assy-Tub Back REMARK

DC97-00214K

WF-F125NC, WF-F105NV, WF-F1254,WF-F1054S,WF-F1054, WF-F854S,WF-F854

3-5-7. Assy- Drum

TYPE (A) (B) (C) CODE-NO. REMARK

DC97-01463J

WF-F125NC, WF-F105NV,WF-F1254,WF-F1054S, WF-F1054,WF-F854S,WF-F854

3-5-8. Assy-pump Drain

1) Capacity : AC 230V 34W 2) Location : Front bottom(R) 3) Resistance : 160 ~ 190
9. SCHEMATIC-DIAGRAM (ROLD)

6. TROUBLE DIAGNOSIS

6-1. TROUBLE DIAGNOSIS

- As the micom wash machine is configured of the complicate structure, there might be the service call. Below information is prepared for exact trouble diagnosis and suitable repair guide.
Caution for the Repair and Replacement
Please follow below instruction for the trouble diagnosis and parts replacement.
1) As some electronic components are damaged by the charged static electricity from the resin part of wash machine or the human body, prepare the human body earth or remove the potential difference of the human body and wash machine by contacting the power supply plug when the work contacting to PCB is executed.
2) Since AC220~240V is applied to the triac T1 and T2 on P.C.B, the electric shock may occur by touching and be careful that the strong and weak electricity are mixed. 3) As the P.C.B assembly is designed for no trouble, do not replace the P.C.B assembly by the wrong diagnosis and follow the procedure of the trouble diagnosis when the micom is not operated normally.
Cause and treatment - Is the PCB connector connected well? - Is the voltage normal? - Is the power supply plug connected well? - Is the noise filter connected well? - Is the secondary output of the power supply transformation normal? - Is the fuse disconnected? (option) If above points are not found, the PCB assembly is out of order. Replace it. - Is the knob open? - Did you push START/PAUSE button after selecting the course? - Is the water supply valve connected well? - Is the winding of the water supply valve continuous? - Is the connection and operation of the pressure switch normal? If above points are not found, the PCB assembly is out of order. Replace it. - Is the connection and operation of the pressure switch normal? - Is the pressure switch hose damaged so that the air is leaked? - Is the pressure switch hose bent? - Check the operation of the water level switch. If above points are not found, the PCB assembly is out of order. Replace it. - Is the belt connected well? - Is the winding of the motor continuous? (Rotor winding, stator winding, generator) - Is the motor protector normal? If above points are not found, the PCB assembly is out of order. Replace it. - The PCB assembly is out of order. Replace it. (Inversion relay open trouble) - Is the drainage hose bent? - Is the winding of the drainage pump continuous? - Is the drain filter clogged by the waste? If above points are not found, the PCB assembly is out of order. Replace it. - The unbalance is detected. - Put in the laundry uniformly and start again. - Is the pulley nut loosen? - Is the transport safety device removed? - Is the product installed on the level and stable place? (Little noise may be generated during the high-speed SPIN.) <When the leak breaker and current breaker is installed separately> - When the leak breaker is down, check and make the earth of the outlet. - When the current is down, the current is leaked. <Is the breaker down when the leak/current breaker is combined?> - Check the rated capacity of the current and leak breaker. The current breaker may be down due to the lack of the current when the wash machine and other apparatus are used.

Check The Surroundings Circuit And TR1,IC7

Exchange The Motor

5V 5V ICC8 TR1 C5 MICOM

R29 R27

6-3. DETAILED DIAGNOSIS
1. Driving Compartment Test Mode A. Hold down the and the buttons simultaneously and then press the Power button. (All of the LEDs light up and the display shows t1 in 3 seconds.) B. The driving part can be tested when you press the push button dial right after entering into the TEST MODE.
Check Motor Water Valve Drain Pump Door S/W Heater Water Pressure Sensor Thermistor
Test Method Check if the motor operates or check the Motor terminals. Check if it supplies water or check the Water Valve terminals. Check if it drains normally or check the pump terminals. Check if it works at the Cotton course or check the Door S/W terminals. Check if it works by changing temperatures at the Cotton course.
Refer to Page 14. (Water Level Table at each Course)
Description Motor Wiring (Red/White /Blue/Pink/Violet/White) Resistance between Blue-Red, Red-White and White-Blue should be 2.010%. Check resistance of the Water Valve terminals. Check resistance of the Drain Pump terminals. Check resistance of the Door S/W terminals. Check resistance of the Heater terminals. Check frequency (Hz) between the Water Pressure Sensor terminals. It varies according to temperatures. (If it is or 0, replace it.) 1.Replace the SUB PCB. 2.If not, replace the Noise Filter.
Check its resistance. 1.Press the buttons on the display. Check if all of the LEDs work. 2.Check if voltage between the white and the black terminals is 220V~240V.

MAIN PCB

9. WIRING DIAGRAM

9-1. PCB ASSY' LAYOUT

Part Number
Display Jog_Dial Power_key Key CN1 RELAY1 RELAY2

Description

Displays or indicates operations or functions Starts/stops an operation to select a course Turns the power on/off Selects and processes each function Detects if the door is open or closed In case of Power_On/Off, supplies or disconnects AC power Disconnects Power from the Heater
CN3 RELAY3 CN4 RELAY4 CN6 CN7
AC1 GND Motor / Motor Wire RPM On/Off Heat Sink Sensor ,Sensor //Pre/Drain

Door System CN10 CN8 CN9

Parts for Door Lock/Unlock Connects Motor Tacho Sensor Connects the silver nano wire Connects the driving system wire
9-2. Connector & Relay Terminals Description (MAIN PCB)

RELAY1

A)Connects to AC2 B)Connects to AC2-1 COMMON
Connects Connects Connects Connects Connects to to to to to SIG-A SIG-B IH PWM GROUND

RELAY2

A)Connects to the HEATER B)Connects to the HEATER
A)Connects to the DOOR LOCK Signal B)Connects to the DOOR LOCK Signal
A) Connects to the TACHO SENSOR B) Connects to the TACHO SENSOR
Connects to AC1 Connects to GROUND
Connects Connects Connects Connects Connects to to to to to the the the the the MOTOR MOTOR MOTOR MOTOR MOTOR STATOR STATOR STATOR STATOR STATOR
Connects to the TEMP SENSOR Connects to the TEMP SENSOR
Connects Connects Connects Connects SENSOR Connects SENSOR to to to to GORUND 5V 5V the WATER
Connects Connects Connects Connects Connects to to to to to the the the the the DRAIN-MOTOR COLD VALVE PRE VALVE HOT VALVE ROLD DOOR S/W

to the TEMP

9-3. Connector & Relay Terminals Description (AG-KIT PBA)
CN1 Connects to AC1 Connects to AC2
CN7 Connects to GORUND Connects to IH Connects to PWM Connects to SIGNAL-B Connects to SIGNAL-A Connects to AG-B Connects to AG-A
4. ALIGNMENT AND ADJUSTMENTS
4-1. GENERAL ERROR FUNCTION
1. An occurrence of an Error will make a sound of error melody for 5sec and continuously show one of the Error Displays from the following errors. (But, Fault Check Led will flash for 0.5sec.) 2. All of the steering parts will be off at that time until that error was released. 3. Water Supply Error - If there is no higher change in water frequency than 100Hz for 2 minutes during the initial time of water supply and if water level doesn't reach the preset level in 10 minutes, this error will occur. This error will be released using Start/Pause button, which performs the initial condition of operation. - Display : 4E 4. Water Drain Error - If water level frequency is still lower than the reset level frequency (25.20kHz) in 10 minutes after starting of water drain, this error will occur. This error will be released using Start/Pause button, which performs the initial condition of operation. - Display : 5E 5. Over Flow Error - If an abnormal water level frequency is sensed (for occurrence of Over Flow :21.00kHz), Auto Power Off may release this error and continuously progress water drain until the frequency reached 25.00kHz. - If Over Flow is also sensed even after the following check of water level frequency indicating that error, it functions to progress water drain. - Display : OE 6. Door Open Error - This error will be released by closing Door. - Display : "dE" 7. Unbalance Error - This error will be released by pressing start/pause S/W. - DISPLAY : UE 8. Water Heater Error - This error will be released by turning off Power S/W. - Display : HE1"(Over Heat), - Display : "HE2", indicating no operation of HE. 9. Pressure S/W (Single Part Trouble) Error Frequency signals(kHz) generated by water level S/W Water Level Abnormal Frequency Low 30.00 KHz High 15.00 KHz

When the unit is not leveled
Lift up the unit a little bit and adjust the shortest. Turn the leveling bolt counter clockwise as shown in the picture above (The leveling leg gets longer.)

Caution

Lock Nut Leveling Bolt Spanner
After adjusting the leveling bolt, tighten the lock nut by turning it clockwise.
Tighten the lock nut after the leveling. If not, it could generate vibrations & noises.

Flat Head Screwdriver

1. Precautions

1-1. Safety Precautions

1. Do not allow the customer to repair the product. It may cause personal injury or product damage when the unit is serviced by unqualified personnel. 2. Disconnect power to the appliance before servicing. Be aware of the possibilities of an electric shock. 3. Do not use multi-plug. Power outlet may be overloaded causing the socket to overheat. 4. Check for any damage on power plug or power outlet. Replace it immediately if it has problem. (It may cause an electric shock or fire) 5. Make sure to earth the product. May cause electric shock. 6. Do not clean the product with water. May cause electric shock / fire or shorten product life. 7. The wiring harness should be free from moisture and connected properly during serving. It should be proof against any external force. 8. Remove any dust or dirt in the product, wiring section and connections during servicing. Protect against possibilities of fire due to tracking etc. 9. Check for any water trace on electrical parts, harness, etc. Replace the parts and /or wipe dry the water. 10. Check the assembled status of the parts after servicing. Check if the product is assembled in the same status as before servicing. 11. Be sure not to pull on the power cord but to unplug it by holding the plug. Beware of possibility of electric shock or fire when the power cord is damaged. 12. Unplug the power plug from the outlet when the washing machine is not used. Beware of possibility of electric shock or fire while lightening. 13. Do not use or put flammable materials (including gasoline, alcohol, thinner etc) around the washing machine. Flammable materials may spark an explosion or fire. 14. Do not put a water containing bowl or wet laundry on the washing machine. It may cause an electric shock or fire, or shorten the product life when its water penetrates into the washing machine. 15. Do not install the washing machine in a place where it is exposed to snow or rain etc. It may cause an electric shock or fire and shorten the product life. 16. Do not press control buttons with pointed objects such as pins, needles, etc. It may cause an electric shock or other problems. 17. Check the washing machine is leveled horizontally on the floor and is installed properly. Vibration may shorten the product life. 18. Make sure to use connectors when connecting wires. If wires are connected without connectors, it may cause a tracking fire. 19. When the washing machine is to be laid down for servicing, put a pad on the floor and lay the product on its side slowly. If the wash machine is laid on its front, internal components may be damaged by the tub.

Can be ironed at 100 max C Do not iron Can be dry cleaned using any solvent Dry clean with perchloride, lighter fuel, pure alcohol or R113 only Dry clean with aviation fuel, pure alcohol or R113 only Do not dry clean
Dry flat Can be hung to dry Dry on clothes hanger Tumble dry, normal heat Tumble dry, reduced heat Do not tumble dry
11-4. ELECTRICAL WARNINGS
To reduce the risk of fire, electrical shock, and other injuries, keep these safety precautions in mind:. Operate the appliance only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied to your home, consult your appliance dealer or local power company. Use only a grounded or polarized outlet. For your safety, this appliance is equipped with a polarized alternating current line plug having one blade wider than the other. This plug will fit into the power outlet only one way. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug still doesn't fit, contact your electrician to replace your outlet. Protect the power cord. Power supply cords should be routed so that they are unlikely to be walked on or pinched by items placed on or against them. Pay particular attention to cords at plugs, convenience receptacles, and the point where they exit from the unit. Do not overload the wall outlet or extension cords. Overloading can result in fire or electric shock.

11-5. Q & A

NO. Type Part Situation Solution method AS rerecomm ended Before consulting cause In case of a cover not being opened or closed
DRUM WASHER 1 (MODEL NAME :Q1*3*) DRUM WASHER 2 (MODEL NAME :Q1*3*) DRUM 3 WASHER (MODEL NAME DRUM Q1*3*) WASHER 4 (MODEL NAME :Q1*3*) DRUM 5 WASHER (MODEL NAME DRUM Q1*3*) 6 WASHER (MODEL NAME DRUM Q1*3*) 7 WASHER (MODEL NAME DRUM Q1*3*) 8 WASHER (MODEL NAME DRUM Q1*3*) 9 WASHER (MODEL NAME DRUM Q1*3*) 10 WASHER (MODEL NAME DRUM Q1*3*) WASHER 11 (MODEL
appearance part Being opened & closed bad/Being attached & detached bad
Door is n drying the d safe level. In
appearance part Label(sticker) being detached consulting for the specification or label of product lead the customer to attach diretly or send the engineer to do so. For other advertisement or PR label it may not be attached. appearance part Accessories being not included appearance part Color coming off/rust.Check whether the componets are AS rerecomm same as those in the manual. If not contact to SVC. ended AS rerecomm ended AS rerecomm ended AS rerecomm ended AS rerecomm ended AS rerecomm ended Others
Is it the la it is for adve is not attach
Sir we re product whic best to clea
It may be occurred when the machine is installed Being rus in the humid place which causes the rust or to the times discoloring. replacemen the location

display part

Display part being not lit up/ not being cleared Character being broken on display Display not being cleared
It is a symptom occurred when it is installed in Dry the fr the humid place or the water is entered its inside. engineer's in

In this ca

Display malfunction

door related

Door sensor not being detected A noise being occurred intermittently during washing A noise being occurred intermittently during dehydrating

a noise

General consulting
Please check whether a washer is installed and used with removing the safety device positioned at its rear.
You are r removed an Please c direction an inside such
Did you remove the washer safety device? It General.Make a comment for the customer to consulting prepare the memorandum since he can may be occurred when the laundry is leaned to one direction or the machine is not aligned not be famaliar with the contents
DRUM 15 WASHER (MODEL NAME DRUM Q1*3*) 16 WASHER (MODEL NAME DRUM Q1*3*) 17 WASHER (MODEL NAME DRUM Q1*3*) WASHER 18 (MODEL NAME :Q1*3*) DRUM 19 WASHER (MODEL NAME DRUM Q1*3*) 20 WASHER (MODEL NAME DRUM Q1*3*) WASHER 21 (MODEL NAME :Q1*3*) DRUM WASHER 22 (MODEL NAME DRUM Q1*3*) WASHER 23 (MODEL NAME :Q1*3*) DRUM 24 WASHER (MODEL NAME DRUM Q1*3*) 25 WASHER (MODEL NAME DRUM Q1*3*) 26 WASHER
Water leakage being occurred at water supply connection Water being overflowed from detergent box(front loading washing machine) Water bein leaked to floor General consulting General consulting General consulting
Lead to reassembe when water supply hose is departed. It may be used with so much detergent or left alone for a long time without use.

Disconnect

water leakage related water leakage related water leakage related

If the det detergent bo

It is a symtom occurred when the hose of bottom Check th not outside is departed or torn off. water drains
water being leaked at water supply connection part
It may be occurred when it is pushed out due to Disconne the water pressure or it has bad connection. because the difficut insta can buy i The leakage during water supply can occur possibly due to the bad connection of tap and coupler and water supply hose.

Detergent being remained

General consulting General consulting
It may appear when the long-term used detergent is not well soluted or when the water temperature is low during winter.

Sove the If it is not so

Water being stopped during the coming in
It may appear when the water is cut or the water Is it chec supply hole is clogged. the water su blackout pus take out t
water supply related water supply related water supply related water supply related rinsing related

Clothes being damaged

One direction rotation
Rotation being not worked after it sounds with buzz Water being not supplied in winter Rinse being not put in tub General consulting
It may appear when the tap and the water supply Make the hose are frozen if it is used at the veranda in the winter. It may appear when the rinse agent remains to clog.
Did the rin putting the r to the reame the cap and

rinsing related

Bubble being remained
It may appear when there is too much or too little If there is laundry. the laundry
water drain related dehydrating related

Water being not drained

Dehydrating time being increased again
General.Make a comment for the customer to The vibration and noise occur when the horizon consulting prepare the memorandum since he can is broken or the laundry are leaned to one not be famaliar with the contents direction. So It may appear when the safety completely. device is operating to prevent it. If the washing machine consumes hours more

If there is severely ent

dehydrating
Washer being worked for four Specific

Check wh

DRUM 57 WASHER (MODEL NAME DRUM Q1*3*) 58 WASHER (MODEL NAME DRUM Q1*3*) 59 WASHER (MODEL NAME DRUM Q1*3*) 60 WASHER (MODEL NAME DRUM Q1*3*) 61 WASHER (MODEL NAME DRUM Q1*3*) 62 WASHER (MODEL NAME DRUM Q1*3*) 63 WASHER (MODEL NAME DRUM Q1*3*) WASHER 64 (MODEL NAME :Q1*3*) DRUM 65 WASHER (MODEL NAME DRUM Q1*3*) WASHER 66 (MODEL NAME :Q1*3*)
dehydrating related dehydrating related dehydrating related others

Not being squeezed well

General consulting AS rerecomm ended
It may appear when there are clothes like vinyl.
Check whe prevent the i request an e
Water being in at purchasing
There ma products tes It may appear when the interior components do not work properly. It may appear when the machine is used at the outside or the veranda.