4_ Safety information

WF203ANW-02463A-02_EN.indd 4

2007-07-02 8:14:48

contents

INSTALLING YOUR WASHER

Unpacking your washer Overview of your washer Electrical Grounding Water Drain Facility Flooring Location Considerations Alcove or Closet Installation Important note to installer Loading your washer Getting started

OPERATING INSTRUCTIONS

WASHING A LOAD OF LAUNDRY
Overview of the control panel Child Lock Garment+ Detergent use Features

MAINTAINING YOUR WASHER

Cleaning the exterior Cleaning the interior Cleaning the dispensers Storing your washer

TROUBLESHOOTING

Check these points if your washer Information codes

APPENDIX

Fabric care chart Helping the environment Specification Cycle chart

Contents _5

WF203ANW-02463A-02_EN.indd 5

installing your washer

UNPACKING YOUR WASHER
Unpack your Washer and inspect it for shipping damage. Make sure you have received all of the items shown below. If your Washer was damaged during shipping, or you do not have all of the items, contact 1-800-SAMSUNG(726-7864).

OVERVIEW OF YOUR WASHER

Hot water supply hose

Cold water supply hose

Detergent drawer Control panel

Drain Hose

Adjustable leg
(use for the Upper Bolt Hole)

Spanner

Bolt hole covers

Water Supply Hose

Rubber Washer

Hose guide

Rubber Cup
BASIC LOCATION REQUIREMENTS

Electrical

120 Volt 60 Hz 15 AMP fuse or circuit breaker Individual branch circuit serving only your Washer is recommended. Your Washer is equipped with a power cord. NEVER USE AN EXTENSION CORD.
6_ Installing your washer
WF203ANW-02463A-02_EN.indd 6

2007-07-02 8:14:50

Grounding
ELECTRICAL GROUNDING IS REQUIRED ON THIS APPLIANCE.
This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a power cord having a three-prong grounding plug for use in a properly installed and grounded outlet. 01 Installing your washer Improper connection of the equipment-grounding conductor can result in a risk of electrical shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded. Do not modify the plug provided with the appliance if it does not fit the outlet, have a proper outlet installed by a qualified electrician.

IMPORTANT SAFETY PRECAUTIONS
To prevent unnecessary risk of fire, electrical shock or personal injury, all wiring and grounding must be done in accordance with the National Electrical Code ANSI/FNPA, No. 70 Latest Revision and local codes and ordinances. It is the personal responsibility of the appliance owner to provide adequate electrical service for this appliance. NEVER CONNECT GROUND WIRE TO PLASTIC PLUMBING LINES, GAS LINES, OR HOT WATER PIPES.
To correctly fill your Washer in the proper amount of time, a water pressure of psi is required. Water pressure less than 20 psi may cause water valve failure, not allowing the water valve to shut off completely. Or, it may extend the fill time beyond what your Washer controls allow, resulting in your Washer turning off. A time limit is built into the controls in the event of an internal hose becoming loose and flooding your home. The water faucets must be within 4 feet/122cm of the back of your Washer for the inlet hoses provided with your Washer. Accessory inlet hoses are available in various lengths up to 10 feet/305cm for faucets that are further away from the back of your Washer. To avoid the possibility of water damage:
Have water faucets easily accessible Turn off faucets when the washer is not in use. Periodically check that there is no leakage from the water inlet hose fittings.
CHECK ALL CONNECTIONS AT THE WATER VALVE AND FAUCET FOR LEAKS.

Drain Facility

The recommended height of the standpipe is 18 in/46 cm. The drain hose must be routed through the drain hose clip to the standpipe. The standpipe must be large enough to accept the outside diameter of the drain hose. The drain hose is attached at the factory.
Installing your washer _7
WF203ANW-02463A-02_EN.indd 7

Flooring

For best performance, your Washer must be installed on a solidly constructed floor. Wood floors may need to be reinforced to minimize vibration and/or unbalanced load situations. Carpeting and soft tile surfaces are contributing factors in vibration and/or tendency for your Washer to move slightly during the spin cycle. Never install your Washer on a platform or weakly supported structure.

Location Considerations

Do not install your Washer in areas where water may freeze, since your Washer will always maintain some water in its water valve, pump, and hose areas. This can cause damage to belts, the pump, hoses and other components. Operating temperature should be above 60F/16C.
Alcove or Closet Installation
MINIMUM CLEARANCES FOR CLOSET AND ALCOVE INSTALLATIONS:
Sides 1 in / 25 mm Top 17 in / 432 mm Rear 4 in / 102 mm Closet Front 2 in / 51 mm If the Washer and Dryer are installed together, the closet front must have at least 72 in or 465 cm of an unobstructed air opening. Your Washer alone does not require a specific air opening.
8_ Installing your washer
WF203ANW-02463A-02_EN.indd 8
IMPORTANT NOTE TO INSTALLER
Please read the following instructions carefully before installing your Washer. These instructions should be retained for future reference. We recommend you hire a professional for installation of this Washer.
STEP 1 Removing the Shipping Bolts
Before using your Washer, you must remove the four shipping bolts from the back of the unit. 1. Loosen all bolts with the supplied spanner. 2. Slide the bolt and spacer up and remove the bolt with the spacer through the hole in the rear wall of your washer. Repeat for each bolt. 3. Fill the holes with the supplied plastic covers. 4. Keep the shipping bolts and spacers for future use.
01 Installing your washer
STEP 2 Selecting a Location
Before you install your Washer, make sure the location: Has a hard, level surface Is away from direct sunlight Has adequate ventilation Will not be freezing (below 32F or 0C) Is away from heat sources such as oil or gas Has enough space so that your Washer need not stand on its power cord Doesnt have any carpeting that will obstruct ventilation openings.
STEP 3 Installing your Washer
1. Place the drain hose in the drain facility. Be sure an airtight connection is NOT made between the drain hose and the standpipe. The standpipe must be at least 18 in or 46 cm high. Caution must always be exercised to avoid collapsing or damaging the drain hose. For best results, the drain hose should not be restricted in any way by elbows, couplings, or excessive lengths. For situations where the drain hose cannot be conveniently elevated to at least 18 in or 46 cm, the drain hose must be supported.

Laundry tub

Hose retainer

Stand pipe

96 Max 18 Min Tie strap

96 Max 18 Min

Installing your washer _9
WF203ANW-02463A-02_EN.indd 9

2007-07-02 8:14:52

2. Insert new rubber washer (supplied) into each end of the inlet hoses. Firmly seat the washers in the couplings.

Cold Hot

3. Check the inlet hose to ensure a washer is inside each fill hose. Thread the inlet hoses to the HOT and COLD faucet connections. On the other end of the hose, check for one rubber washer per hose and install each fill hose to the water valve. Make sure the hose with the Hot printed line is attached to the HOT faucet. Tighten by hand until snug, then two-thirds of a turn with pliers. For correct water use, connect both HOT and COLD water valves. If one is not connected, an nF (no fill) error can occur. 4. Turn on the HOT and COLD water supply and check all connections at the water valve and the faucet for leaks.

Rubber washer

Cold printed

Hot printed

5. Plug the power cord into a 3-Prong, well grounded 120 volt 60 Hz approved electrical outlet protected by a 15-amp fuse or comparable circuit breaker. Your Washer is grounded through the third prong of the power cord when plugged into a three-prong grounded receptacle.
6. Slide your Washer into position.
7. Level your Washer by turning the leveling legs in or out as necessary by hand or wrench included with your Washer. When your Washer is level, tighten the nuts using the wrench or (-) driver. Your Washer must be leveled on all four sides. A carpenters level should be used on all four corners of your Washer. Its a good idea after the first dozen washes to recheck your Washers levelness. 8. Before installing the rubber-cup, attach the tape provided to the base of the rubber-cup.
10_ Installing your washer
WF203ANW-02463A-02_EN.indd 10

2007-07-02 8:14:55

operating instructions

LOADING YOUR WASHER

You can fill the Washer with dry, unfolded clothes; but DO NOT OVERLOAD the Washer. Overloading may reduce washing efficiency, cause excess wear, and possibly cause creasing or wrinkling of the load. Wash delicate items such as bras, hosiery, and other lingerie in the Delicates/Hand Wash cycle with similar lightweight items. When washing big bulky items or a few smaller items that dont fill the Washer completely a rug, a pillow, stuffed toys, or one or two sweaters, for example add a few towels to improve tumbling and spin performance. Do not put king and queen size bed covering in the Washer. During the spin cycle, the Washer may add additional water to redistribute the excessive unbalance inside the drum. When washing heavily soiled loads, not overloading your Washer is very important to assure good cleaning results. To add a forgotten item: 1. Press the Start/Pause Button. 2. Wait for the Door Lock light to go out (5 seconds) 3. Add the item, close the door, and press the Start/Pause Button. After a pause of 10 seconds, the cycle will resume. To ensure thorough cleaning, add items within five minutes of starting the wash cycle. Try washing bedding, towels, undergarments, and other articles that usually have close body contact using the SilverCare Option, which sanitizes using cold water. 02 Operating instructions

GETTING STARTED

1. Load your Washer. 2. Close the door. 3. Add detergent and additives to the dispenser (see pages 15~16). 4. Select the appropriate cycle and options for the load (see pages 12~14). 5. Press the Start/Pause Button. 6. The Wash Indicator light will illuminate. 7. The estimated cycle time will appear in the display. The time may fluctuate to better indicate the time remaining in the cycle. 8. Before your Washer starts to fill, it will make a series of clicking noises to check the door lock and do a quick drain. When the cycle is complete, the Door Lock light will go out and End will appear in the display. DO NOT attempt to open the door until the Door Lock light is off. To add a forgotten item, see Loading your Washer section. (page 11) When your Washer is restarted after a pause, expect a delay of up to 15 seconds before the cycle continues. Pressing Power cancels the cycle and stops your Washer. The Pre Wash, Wash, Rinse and Spin indicator lights will illuminate during those portions of the cycle.
Operating instructions _11
WF203ANW-02463A-02_EN.indd 11
washing a load of laundry
OVERVIEW OF THE CONTROL PANEL

Digital graphic display

Displays the remaining cycle time, all cycle information, and error messages. Press the button repeatedly to cycle through the different water temperature options. Hot/Cold - Whites and heavily soiled, colorfast items.
Temperature selection button
Warm/Warm - Colorfast items. When warm rinse is selected, only the final rinse will be warm. The other rinses will be cold to conserve energy. Warm/Cold - Moderately soiled, colorfast items; most wrinkle-free items. Cold/Cold - Brightly colored, very lightly soiled items. Press the button repeatedly to cycle through the different spin speed options. To minimize wrinkling of wrinkle-free and no-iron fabrics, DO NOT use the Extra High spin option or overload your Washer.

Spin selection button

High - Use for underwear, t-shirts, jeans and sturdy cottons. Medium - Use for jeans, wrinkle-free or wash-and-wear items and synthetics. Low - Use for delicate items needing a slow spin speed. No Spin - Drains your Washer without spinning. Use for extremely delicate items that cannot tolerate any spin. Press the button to select the Soil Level/Washing Time.

Soil Level selection button
Heavy - For heavily soiled loads. Normal - For moderately soiled loads. This setting is best for most loads. Light - For lightly soiled loads.

Signal selection button

Press the button to increase or decrease the end of cycle signal volume or turn off the signal.
12_ Washing a load of laundry
WF203ANW-02463A-02_EN.indd 12

2007-07-02 8:14:56

Press these buttons to select different cycle options.

Select Cycle Option

Delay Start - Any cycle can be delayed for up to 12 hours in one-hour increments. The displayed hour indicates the time at which the wash will be started. Extra Wash - Add additional time to the wash for better stain removal. Extra Rinse - Add an additional rinse at the end of the cycle to more thoroughly remove laundry additives and perfumes. Select the appropriate cycle for the type of load. This will determine the tumble pattern and spin speed for the cycle. To minimize wrinkling of laundry, select the Perm Press cycle. Heavy Duty - For sturdy, colorfast fabrics and heavily soiled garments. Normal - For most fabrics including cottons, linens, and normally soiled garments. Whites - For white fabrics with or without bleach. 03 Washing a load of laundry

Cycle Selector

Perm Press - For wash-and-wear, synthetic fabrics, and lightly to normally soiled garments. Sanitize - For heavily soiled, colorfast garments. This cycle heats the water to 150F to eliminate bacteria. If Pause is selected during the heating portion of the Sanitize Cycle, your Washer door will remain locked for your safety. Rinse + Spin - Use for loads that need rinsing only or to add rinse-added fabric softener to a load. Spin Only - Provides a spin to remove more water.
Start/Pause selection button Power button
Press to pause and restart programs. Press once to turn your Washer on, press again to turn your Washer off. If
the Washer is left on for more than 10 minutes without any buttons being touched, the power automatically turns off.
Washing a load of laundry _13
WF203ANW-02463A-02_EN.indd 13

2007-07-02 8:14:57

Child Lock
A function that prevents children from playing with your Washer.

ACTIVATING/DEACTIVATING

If you want to activate/deactivate the Child Lock function, press the Soil Level and Signal buttons at the same time for 3 seconds. How It Works: 1. The Child Lock can be activated while your Washer is running. 2. Once you activate the Child Lock, all controls (except for the Power button) will be locked until you deactivate the Child Lock. 3. The Child Lock button will be lit while it is in effect. When buttons, other than the Power button, do not respond, please check if the Child Lock function is on.

Garment+

You can add or take out laundry items even after the wash has started, as long as the Garment+ light is on. Pushing the Start/Pause button unlocks the door, unless the water is too hot or if there is too much water in your Washer. If you are able to unlock the door and wish to continue the wash cycle, close the door and press the Start/Pause button.
14_ Washing a load of laundry
WF203ANW-02463A-02_EN.indd 14

DETERGENT USE

Your Washer is designed to use high efficiency (HE) detergents. For best cleaning results, use a high efficiency detergent such as Tide HE, Wisk HE, Cheer HE or Gain HE*. High efficiency detergents contain suds suppressors that reduce or eliminate suds. When fewer suds are produced, the load tumbles more efficiently and cleaning is maximized. Regular detergent is NOT recommended. Please use only HE detergent. Reducing the amount of detergent may reduce cleaning. It is important to pretreat stains, sort carefully by color and soil level, and avoid overloading. * Brand names are trademarks of their respective manufacturers. 03 Washing a load of laundry

FEATURES

Automatic dispenser
Your Washer has separate compartments for dispensing detergent and color-safe bleach, chlorine bleach, and fabric softener. All laundry additives are added to their respective compartments before starting your Washer. The automatic dispenser MUST ALWAYS be in place before starting your Washer. DO NOT open the automatic dispenser when your Washer is running. To use: 1. Pull out the dispenser drawer on the left side of the control panel. 2. Add recommended quantity of additive to the appropriate compartments with laundry additives, being careful not to overfill or spill. 3. Slide the dispenser drawer carefully and completely back into the compartment.
Detergent compartment Detergent selector

Detergent compartment

1. Pour the recommended amount of laundry detergent directly into the detergent compartment before starting your Washer. 2. If color-safe bleach is to be used, it should be added with detergent to the detergent compartment. When adding color-safe bleach with detergent, it is best if both laundry products are in the same form granular or liquid. If using liquid detergent, lower the detergent selector and add the detergent to the detergent compartment.

Washing a load of laundry _15
WF203ANW-02463A-02_EN.indd 15

2007-07-02 8:14:58

Bleach compartment
(Liquid chlorine bleach only) 1. Add chlorine bleach to the bleach compartment. DO NOT exceed the MAX FILL line. 2. Avoid splashing or overfilling the compartment. 3. Your Washer automatically dispenses bleach into the tub at the appropriate time. 4. The dispenser automatically dilutes liquid chlorine bleach before it reaches the wash load. Never pour undiluted liquid chlorine bleach directly onto the load or into the tub. It is a powerful chemical and can cause fabric damage, such as weakening of the fibers or color loss, if not used properly. If you prefer to use colorsafe, nonchlorine bleach, add it to the appropriate detergent compartment. DO NOT pour colorsafe bleach into the Bleach compartment.
Fabric Softener compartment Bleach compartment
Fabric Softener Compartment
1. Pour the recommended amount of liquid fabric softener into the softener compartment. For smaller loads, use less than one capful. 2. Fabric softener should be diluted with water until it reaches MAX FILL in the compartment. 3. The dispenser automatically releases liquid fabric softener at the proper time during the rinse cycle. Use the softener compartment ONLY for liquid fabric softeners. DO NOT use the Downy Ball* in Fabric softner Compartment with this Washer. It will not add fabric softener at the appropriate time. Use the detergent Compartment. Brand names are trademarks of their respective manufacturers.
16_ Washing a load of laundry
WF203ANW-02463A-02_EN.indd 16

maintaining your washer

CLEANING THE EXTERIOR
Turn off the water faucets after finishing the days washing. This will shut off the water supply to your Washer and prevent the unlikely possibility of damage from escaping water. Leave the door open to allow the inside of your Washer to dry out. Use a soft cloth to wipe up all detergent, bleach or other spills as they occur. Clean the following as recommended: Control Panel Clean with a soft, damp cloth. Do not use abrasive powders or cleaning pads. Do not spray cleaners directly on the panel. Cabinet Clean with soap and water. 03 Maintaining your washer

CLEANING THE INTERIOR

Clean the interior of your Washer periodically to remove any dirt, soil, odor, mold, mildew, or bacterial residue that may remain in your Washer as a result of washing clothes. Failure to follow these instructions may result in unsatisfactory conditions, including unpleasant odor and/or permanent stains on your Washer or laundry. Hard water deposits may be removed, if needed. Use a cleaner labeled Washer safe.

CLEANING THE DISPENSERS

The Automatic Dispenser may need to be cleaned periodically due to laundry additive buildup. 1. Press the release lever on the inside of the dispenser and pull out. 2. Remove the Siphon Cap from the fabric softener and bleach compartments. 3. Wash all of the parts under running water. 4. Clean the dispenser recess with a soft brush. 5. Reinsert the Siphon Cap, pushing them firmly into place. 6. Push the dispenser back into place. 7. Run a Rinse & Spin cycle without any load in your Washer. 2

Siphon cap

STORING YOUR WASHER
Washers can be damaged if water is not removed from hoses and internal components before storage. Prepare your Washer for storage as follows: Select the Quick Wash cycle and add bleach to the automatic dispenser. Run your Washer through the cycle without a load. Turn the water faucets off and disconnect the inlet hoses. Unplug your Washer from the electrical outlet and leave your Washer door open to let air circulate inside the tumbler. If your Washer has been stored in belowfreezing temperatures, allow time for any leftover water in your Washer to thaw out before use.
Maintaining your washer _17
WF203ANW-02463A-02_EN.indd 17

2007-07-02 8:14:59

troubleshooting
CHECK THESE POINTS IF YOUR WASHER
PROBLEM will not start. SOLUTION has no water or not enough water. has detergent remains in the automatic dispenser after the wash cycle is complete. vibrates or is too noisy. Make sure the door is firmly closed. Make sure your Washer is plugged in. Make sure the water source faucets are turned on. Make sure to press the Start/Pause Button to start your Washer. Make sure the Child Lock is not activated; see page C4. Before your Washer starts to fill, it will make a series of clicking noises to check the door lock and do a quick drain. Check the fuse or reset the circuit breaker Turn both faucets on fully. Make sure the door is tightly closed. Straighten the water inlet hoses. Disconnect hoses and clean screens. Hose filter screens may be plugged. Open and close the door, then press the Start/Pause Button. Make sure your Washer is running with sufficient water pressure. Make sure the Detergent Selector dial is in the upper position when using granular detergent. Make sure your Washer is set on a level surface. If the surface is not level, adjust your Washer feet to level the appliance. Make sure that the shipping bolts are removed. Make sure your Washer is not touching any other object. Make sure the laundry load is balanced. Plug the power cord into a live electrical outlet. Check the fuse or reset the circuit breaker. Close the door and press the Start/Pause Button to start your Washer. For your safety, your Washer will not tumble or spin unless the door is closed. Before your Washer starts to fill, it will make a series of clicking noises to check the door lock and do a quick drain. There may be a pause or soak period in the cycle. Wait briefly and it may start. Check the screens on the inlet hoses at the faucets for obstructions. Clean the screens periodically.

Troubleshooting _21

WF203ANW-02463A-02_EN.indd 21

2007-07-02 8:15:04

appendix

FABRIC CARE CHART

The following symbols provide garment care direction. The Clothing care labels include symbols for washing, bleaching, drying and ironing, or dry cleaning when necessary. The use of symbols ensures consistency among garment manufacturers of domestic and imported items. Follow care label directions to maximize garment life and reduce laundering problems. Wash Cycle Normal Permanent Press / Wrinkle Resistant / Wrinkle Control Gentle/Delicates Hand Wash Water Temperature** Hot Warm Cold Bleach Any Bleach (when needed) Only Non-Chlorine (color-safe) Bleach (when needed) Tumble Dry Cycle Normal Special Instructions Line Dry/ Hang to Dry Drip Dry Dry Flat Heat Setting High Medium Low Any Heat No Heat/Air Iron-Dry or Steam Temperatures High Medium Low Warning Symbols for Laundering Do Not Wash Do Not Wring Do Not Bleach Do Not Tumble Dry No Steam (added to iron) Do Not Iron Dryclean Dry Clean Do Not Dry Clean Line Dry/ Hang to Dry Drip Dry Dry Flat
For machine-washable wool. Loads should be under 8 pounds.
Permanent Press/ Wrinkle Resistant/ Wrinkle Control Gentle/ Delicates ** The dot symbols represent appropriate wash water temperatures for various items. The temperature range for Hot is 105 - 125 F/ 41 - 52C, for Warm 85 - 105 F/29 - 41 C and for Cold 60 - 85 F/16 - 29 C. (Wash water temperature must be a minimum of 60 F/16C for detergent activation and effective cleaning.) The Washer may not ensure these temperatures because the actual water temperatures entering your Washer are dependent on water heater settings and regional water supply temperatures. For example, cold water entering the home in the northern states during winter may be 40 F/4 C which is too cold for effective cleaning. The water temperature in this situation will need to be adjusted by selecting a warm setting, adding some hot water to the MAX FILL line or using your Washers heating option, if available.

22_ Appendix

WF203ANW-02463A-02_EN.indd 22

HELPING THE ENVIRONMENT

Your Washer is manufactured from recyclable materials. If you decide to dispose of it, please observe local waste disposal regulations. Cut off the power cord so that the appliance cannot be connected to a power source. Remove the door so that animals and small children cannot get trapped inside the appliance. Do not exceed the detergent quantities recommended in the detergent manufacturers instructions. 06 Appendix Use stain removal products and bleaches before the wash cycle only when necessary. Save water and electricity by only washing full loads (the exact amount depends upon the program used).

Appendix _23

WF203ANW-02463A-02_EN.indd 23

2007-07-02 8:15:05

DECLARATION OF CONFORMITY
This appliance complies with UL2157.

SPECIFICATION

TYPE FRONT LOADING WASHER

DIMENSION

Div A. HeightOverall B. Width
Inches (cm) 38 (96.5) 27 (68.6)
Div C. Depth with door open 90 D. Depth
Inches (cm) 48.4(123) 29.65(75)
WATER PRESSURE WEIGHT HEATER RATING POWER CONSUMPTION WASHING WASHING AND HEATING SPIN DRAIN SPIN REVOLUTION WF203*
50 kPa ~ 800 kPa 85 kg(187.4 lb) 900 W 120 V 120 V 120 V 120 V 1000 rpm 240 W 1120 W 600 W 41 W

24_ Appendix

WF203ANW-02463A-02_EN.indd 24

2007-07-02 8:15:28

CYCLE CHART
Use this chart to set the best cycle and option for you laundry. 203ANW, 203ANS

FUNCTION

Temp H/C W/W W/C C/C H M Spin L NS H Soil Level N L Delay Start Extra Wash Extra Rinse

OPTIONS Time (mins)

06 Appendix
Heavy Duty Normal Whites Perm Press Sanitize Rinse + Spin Spin Only
Temp H/C: Hot/Cold W/W: Warm/Warm W/C: Warm/Cold C/C : Cold/Cold
Spin H: High M: Medium L: Low NS: No Spin
Soil Level H: Heavy N: Normal L: Light

Appendix _25

WF203ANW-02463A-02_EN.indd 25

2007-07-02 8:15:30

warranty
SAMSUNG WASHER LIMITED WARRANTY TO ORIGINAL PURCHASER This SAMSUNG brand product, as supplied and distributed by SAMSUNG ELECTRONICS AMERICA, INC. (SAMSUNG) and delivered new, in the original carton to the original consumer purchaser, is warranted by SAMSUNG against manufacturing defects in materials and workmanship for a limited warranty period of: One (1) Year All Parts and Labor. This limited warranty begins on the original date of purchase, and is valid only on products purchased and used in the United States. To receive warranty service, the purchaser must contact SAMSUNG for problem determination and service procedures. Warranty service can only be performed by a SAMSUNG authorized service center. The original dated bill of sale must be presented upon request as proof of purchase to SAMSUNG or SAMSUNGs authorized service center. SAMSUNG will provide in-home service during the warranty period at no charge, subject to availability within the contiguous United States. In-home service is not available in all areas. To receive in-home service, product must be unobstructed and accessible to the service agent. If service is not available, SAMSUNG may elect to provide transportation of the product to and from an authorized service center. SAMSUNG will repair, replace, or refund this product at our option and at no charge as stipulated herein, with new or reconditioned parts or products if found to be defective during the limited warranty period specified above. All replaced parts and products become the property of SAMSUNG and must be returned to SAMSUNG. Replacement parts and products assume the remaining original warranty, or ninety (90) days, whichever is longer.This limited warranty covers manufacturing defects in materials and workmanship encountered in normal, noncommercial use of this product and shall not apply to the following: damage that occurs in shipment; delivery and installation; applications and uses for which this product was not intended; altered product or serial numbers; cosmetic damage or exterior finish; accidents, abuse, neglect, fire, water, lightning, or other acts of nature or God; use of products, equipment, systems, utilities, services, parts, supplies, accessories, applications, installations, repairs, external wiring or connectors not supplied or authorized by SAMSUNG that damage this product or result in service problems; incorrect electrical line voltage, fluctuations and surges; customer adjustments and failure to follow operating instructions, maintenance and environmental instructions that are covered and prescribed in the instruction book; product removal and reinstallation; problems caused by pest infestations. This limited warranty does not cover problems resulting from incorrect electric current, voltage or supply, light bulbs, house fuses, house wiring, cost of a service call for instructions, or fixing installation errors. SAMSUNG does not warrant uninterrupted or error-free operation of the product.

26_ Warranty

WF203ANW-02463A-02_EN.indd 26
EXCEPT AS SET FORTH HEREIN, THERE ARE NO WARRANTIES ON THIS PRODUCT EITHER EXPRESS OR IMPLIED, AND SAMSUNG DISCLAIMS ALL WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, INFRINGEMENT OR FITNESS FOR A PARTICULAR PURPOSE. NO WARRANTY OR GUARANTEE GIVEN BY ANY PERSON, FIRM, OR CORPORATION WITH RESPECT TO THIS PRODUCT SHALL BE BINDING ON SAMSUNG. SAMSUNG SHALL NOT BE LIABLE FOR LOSS OF REVENUE OR PROFITS, FAILURE TO REALIZE SAVINGS OR OTHER BENEFITS, OR ANY OTHER SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE, OR INABILITY TO USE THIS PRODUCT, REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF SAMSUNG HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. NOR SHALL RECOVERY OF ANY KIND AGAINST SAMSUNG BE GREATER IN AMOUNT THAN THE PURCHASE PRICE OF THE PRODUCT SOLD BY SAMSUNG AND CAUSING THE ALLEGED DAMAGE. WITHOUT LIMITING THE FOREGOING, PURCHASER ASSUMES ALL RISK AND LIABILITY FOR LOSS, DAMAGE, OR INJURY TO PURCHASER AND PURCHASERS PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF THE USE, MISUSE, OR INABILITY TO USE THIS PRODUCT. THIS LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS PRODUCT, IS NONTRANSFERABLE AND STATES YOUR EXCLUSIVE REMEDY. Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific rights, and you may also have other rights, which vary from state to state. To obtain warranty service, please contact SAMSUNG at: SAMSUNG ELECTRONICS AMERICA, INC. CONSUMER ELECTRONICS CUSTOMER SERVICE 400 Valley Road, Suite 201, Mt. Arlington, NJ 07856 1-800-SAMSUNG (1-800-726-7864) www.samsung.com

Warranty _27

WF203ANW-02463A-02_EN.indd 27

QUESTIONS OR COMMENTS?

Country USA CANADA CALL 1-800-SAMSUNG (726-7864) 1-800-SAMSUNG (726-7864) OR VISIT US ONLINE AT www.samsung.com www.samsung.com/ca
Code No. DC68-02463A-02_EN
WF203ANW-02463A-02_EN.indd 28

Lave-linge

manuel dutilisation

imaginez les possibilits

Merci de votre achat dun produit SAMSUNG.