Step 3: Mounting the Wall Plate - wood stud, brick, solid concrete and concrete block mounting options are provided Wood Stud Installation: The Wall Plate (a) must be installed into a single wood stud. Use the Wall Plate as a template mark a location on the wall, one in the top row of slots and the other in the corresponding slot in the bottom row. Pre drill a 2.5 deep hole into the wood stud by using a 3/16 drill bit. Make sure wall the Wall Plate is oriented to the flat surface is against the wall. Attach the Wall Plate to the wall using two Lag Bolts (d) and two Lag Bolt Washers (e). See Diagram 3a for assistance. Brick, solid concrete and concrete block installation: Use the Wall Plate (a) as a template to mark 3 locations on the wall. Two in the top row of slots and one more centered in the bottom row. Carefully pre-drill a 2.5 deep hole with a 1/2 masonry drill bit. Never drill into the mortar between blocks! Insert a Concrete Anchor (f) into each pre-drilled hole so it is flush with the concrete/brick surface even if there is a layer of drywall or other material in front. Attach the Wall Plate to the wall using three Lag Bolts (d) and three Lag Bolt Washers (e). See Diagram 3b for assistance. Warning: Do not overtighten the Lag Bolts! Tighten Lag Bolts only until the Lag Bolt Washer is pulled firmly against the Wall Plate. Diagram 3a Diagram 3b
Assembly Instructions for Model: VM200
Thank you for choosing a Sanus Systems VisionMount wall mount. The VM200 is designed to mount up to 40 LCD TVs weighing less than 80 lbs to a vertical wall. It will allow you to effortlessly tilt the TV 20. Safety Warning: If you do not understand these directions, or have any doubts about the safety of the installation, please call a qualified contractor or contact Sanus at 800.359.5520 or www.sanus.com. Check carefully to make sure that there are no missing or defective parts. Our customer service representatives can quickly assist you with installation questions and missing or damaged parts. Replacement parts for products purchased through authorized dealers will be shipped directly to you. Never use defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified by Sanus Systems. Sanus Systems can not be liable for damage or injury caused by incorrect mounting, incorrect assembly, or incorrect use. Please call Sanus Systems before returning products to the point of purchase. Note: The supplied wall mounting hardware is not for metal stud or old cinder block walls. If you are uncertain about the nature of your wall, consult an installation contractor. Sanus makes every effort to assure all necessary television mounting hardware is included. If the hardware you need is not included please consult your local hardware store or call Sanus Systems. Required Tools: Drill, 3/16 drill bit, (1/2 masonry bit for brick, concrete, or concrete block installations), socket set and a Phillips screw driver
Supplied Parts and Hardware: Some parts not shown as actual size*
a (1) Wall Plate - a* (1) Left Monitor Bracket - b* (1) Right Monitor Bracket - c*
Step 4: Attach Monitor to Wall Plate Rotate the latch handle into its most open position and hang the hooks of the Left and Right Monitor Brackets (b,c) over the tab on the top of the Wall Plate (a) as shown in Diagram 4a. Once the Monitor Brackets are attached to the Wall Plate, rotate the latch handles on each Monitor Bracket until they click into place. The tip of the latch handle should now be tucked up behind the tab on the bottom of the Wall Plate as shown in the Detailed View of Diagram 4b. You may place a pad lock through the hole in the bottom of the latch handle if you wish to add security to the installation. Diagram 4a Diagram 4b Detailed View
(3) Lag Bolt - d (3) Lag Bolt Washer - e TV Mounting Hardware:

(3) Concrete Anchor - f

b,c bottom tab tip of latch handle

(4) M4 x 10 mm Bolt - g

(4) M5 x 12 mm Bolt - h

(4) M6 x 12 mm Bolt - i

(4) M4 x 30 mm Bolt - j

(4) M5 x 30 mm Bolt - k

(4) M6 x 35 mm Bolt - l

(4) M4 Lock Washer - m

(4) M5 Lock Washer - n

(4) M6 Lock Washer - o

hole for latch padlock handle
Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 8.17.05 Customer Service: 800.359.5520. See complementary Sanus products at www.sanus.com

(4) M4/M5 Washer - p

(4) M6 Washer - q

(4) M4/M5 Spacer - r

(4) M6 Spacer - s
Step 1: Mount Monitor Brackets to a television with a flat back First, determine the diameter of the Bolt (g,h,i) your TV requires by hand threading them into the threaded insert on the back of the TV. If you encounter any resistance stop immediately! Once you have determined the correct diameter, see the appropriate Diagram below. You will thread the Bolt through the appropriate Lock Washer (m,n,o), the corresponding Washer (p,q), the Monitor Bracket (b,c), and finally into the TV. Make sure the Monitor Brackets are vertically centered and level with each other. See the appropriate Diagram below. Note: For televisions with a curved back, or an obstruction near the threaded insert see Step 2. M4 Diameter Bolt M6 Diameter Bolt
Step 2: Mount Monitor Brackets to a television with a curved back or an obstruction near the threaded insert
First, determine the diameter of the Bolt (j,k,l) your TV requires by hand threading them into the threaded insert on the back of the TV. If you encounter any resistance stop immediately! Once you have determined the correct diameter, see the appropriate Diagram below. You will thread the Bolt through the appropriate Lock Washer (m,n,o), the corresponding Washer (p,q), the Monitor Bracket (b,c), a Spacer (r,s), and finally into the TV. Make sure the Monitor Brackets are vertically centered and level with each other. See the appropriate Diagram below. M4 Diameter Bolt M6 Diameter Bolt

c b i o q

j m s q

M5 Diameter Bolt

Diagram 1

M5 Diameter Bolt

Diagram 2

r n p

Assembly Instructions for Model: VM200
Thank you for choosing a Sanus Systems VisionMount wall mount. The VM200 is designed to mount up to 40 LCD TVs weighing less than 80 lbs [36.3 Kg] to a vertical wall. It will allow you to effortlessly tilt the TV 20 CAUTION: The size and weight of your television must not exceed 40 [1016 mm] diagonally and 80 Lbs [36.3 Kg]. The wall must be capable of suporting five times the weight of the televison plus the wall mount. Never use defective parts. Improper installation may cause property damage or personal injury. Do not use this product for any purpose that is not explicitly specified by Sanus Systems. If you do not understand these directions, or have any doubts about the safety of the installation, please call a qualified contractor or contact Sanus Systems at 800.359.5520 or www.sanus.com. Our customer service representatives can quickly assist you with installation questions and missing or damaged parts. Replacement parts for products purchased through authorized dealers will be shipped directly to you. Check carefully to make sure that there are no missing or defective parts. Sanus Systems can not be liable for damage or injury caused by incorrect mounting, incorrect assembly, or incorrect use. Please call Sanus Systems before returning products to the point of purchase NOTE: The supplied wall mounting hardware is not for metal stud or old cinder block walls. If you are uncertain about the nature of your wall, consult an installation contractor. Sanus makes every effort to assure all necessary television mounting hardware is included. If the hardware you need is not included please consult your local hardware store or call Sanus Systems. Required Tools: Drill, 3/16 drill bit, (1/2 masonry bit for brick, concrete, or concrete block installations), wrench set, phillips screw driver Supplied Parts and Hardware: (All threaded fasteners are shown full size.)

Wall Plate - A Qty. 1

Left Monitor Bracket - B Qty. 1
Right Monitor Bracket - C Qty. 1

Lag Bolt - D Qty. 3

Lag Bolt Washer - E Qty. 3
Concrete Anchor - F Qty. 3
M4 x 12 mm Bolt - G Qty. 4
M5 x 12 mm Bolt - H Qty. 4
M6 x 12 mm Bolt - I Qty. 4
M4 x 30 mm Bolt - J Qty. 4
M5 x 30 mm Bolt - K Qty. 4
M6 x 35 mm Bolt - L Qty. 4
M4 Lock Washer - M Qty. 4
M5 Lock Washer - N Qty. 4
M6 Lock Washer - O Qty. 4

M4/M5 Washer - P Qty. 4

M6 Washer - Q Qty. 4

M4/M5 Spacer - R Qty. 4

M6 Spacer - S Qty. 4
Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 06.08.06 (6901-100024) Customer Service: 800.359.5520. See complementary Sanus products at www.sanus.com
Step 1: Mount Monitor Brackets to a television with a flat back NOTE: For televisions with a curved back, or an obstruction near the threaded insert see Step 2. Determine the diameter of the Bolt (G,H,I) your TV requires by hand threading them into the threaded insert on the back of the TV. If you encounter any resistance stop immediately. Once you have determined the correct diameter, see the appropriate Diagram below, thread the Bolt through the appropriate Lock Washer (M,N,O), corresponding Washer (P,Q), Monitor Bracket (B,C), and finally into the TV. Make sure the Monitor Brackets (B,C) are vertically centered and level with each other. Tighten the Bolts (G,H,I) securing the Monitor Brackets (B,C) to the monitor. NOTE: If the horizontal distance between the threaded inserts on the back of the television is greater than 8-1/8 inches [206 mm] but less than 11-1/8 inches [282.5 mm], the locations of the Monitor Brackets (B & C) may be reversed from right to left. If the Monitor Brackets are reversed, the Tension Knobs must be removed and reinstalled so that they are still facing out.

M4 Diameter Bolt P

Diagram 1 Tension Knob Tension Knob

M5 Diameter Bolt N P

H M6 Diameter Bolt
Step 2: Mount Monitor Brackets to a television with a curved back or an obstruction near the threaded insert Determine the diameter of the Bolt (J,K,L) your TV requires by hand threading them into the threaded insert on the back of the TV. If you encounter any resistance stop immediately. Once you have determined the correct diameter, see the appropriate Diagram below, thread the Bolt through the appropriate Lock Washer (M,N,O), the corresponding Washer (P,Q), the Monitor Bracket (B,C), a Spacer (R,S), and finally into the TV. Make sure the Monitor Brackets are vertically centered and level with each other. See the appropriate Diagram below. Tighten the Bolts (J,K,L) securing the Monitor Brackets (B,C) to the monitor.

M4 Diameter Bolt

NOTE: If the horizontal distance between the threaded inserts on the back of the television is greater than 8-1/8 inches [206 mm] but less than 11-1/8 inches [282.5 mm], the locations of the Monitor Brackets (B & C) may be reversed from right to left. If the Monitor Brackets are reversed, the Tension Knobs must be removed and reinstalled so that they are still facing out.

Diagram 2

Tension Knob Tension Knob

M5 Diameter Bolt

M6 Diameter Bolt
Step 3: Mounting the Wall Plate - wood stud, brick, solid concrete and concrete block mounting options are provided Wood Stud Installation: CAUTION: Do not over tighten the Lag Bolts. Tighten Lag Bolts (D) only until the Lag Bolt Washer (E) is pulled firmly against the Wall Plate (A). If there is a layer of drywall or other material, this drywall or other material may not exceed 5/8 inch [15.8 mm] in thickness. Failure to heed this caution may result property damage and/or personal injury. Use the Wall Plate as a template mark a location on the wall, one in the top row of slots and the other in the corresponding slot in the bottom row. Pre-drill a 2.5 deep hole into the wood stud by using a 3/16 drill bit, making sure wall the Wall Plate is oriented to the flat surface is against the wall. Attach the Wall Plate to the wall using two Lag Bolts (D) and two Lag Bolt Washers (E). See Diagram 3A for assistance. Brick, solid concrete and concrete block installation: Use the Wall Plate (A) as a template to mark 3 locations on the wall. Two in the top row of slots and one more centered in the bottom row. CAUTION: Always locate Concrete Anchors (F) in the brick, block, or concrete. Never drill into the mortar between blocks. Make sure the Concrete Anchor is seated flush with the concrete surface even if there is a layer of drywall or other material. This drywall or other material may not exceed 5/8 inch [15.8 mm] in thickness. Failure to heed this caution may result in property damage and/or personal injury. Carefully pre-drill a 2.5 deep hole with a 1/2 masonry drill bit. Insert a Concrete Anchor (F) into each pre-drilled hole so it is flush with the concrete/brick surface, even if there is a layer of drywall or other material in front; then, attach the Wall Plate (A) to the wall using three lag Bolts (D) an three Lag Bolt Washers (E). See Diagram 3B for assistance E D A A Step 4: Attach Monitor to Wall Plate CAUTION: Some televisions may require two people to lift. Sanus is not responsible for personal injury or product damage. Rotate the Latch Handle into its most open position and hang the hooks of the Left and Right Monitor Brackets (B,C) over the tab on the top of the Wall Plate (A) as shown in Diagram 4A. Once the Monitor Brackets (B,C) are attached to the Wall Plate, rotate the Latch Handles on each Monitor Bracket until they click into place. The tip of the Latch Handle should now be tucked up behind the tab on the bottom of the Wall Plate as shown in the Detailed View of Diagram 4B. You may place a padlock through the hole in the bottom of the latch handle if you wish to add security to the installation. Diagram 4A Diagram 4B Bottom tab of Wall Plate (A) Top tab of Wall Plate (A) Tip of Latch Handle Diagram 3A D Diagram 3B E F

Latch Handle

Hole for Padlock
CSAV, Inc. and its affiliated corporations and subsidiaries (collectively, CSAV), intend to make this manual accurate and complete. However, CSAV makes no claim that the information contained herein covers all details, conditions, or variations. Nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. CSAV makes no representation of warranty, expressed or implied, regarding the information contained herein. CSAV assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.