For transporting the machine into the location's building, the minimum necessary dimensions of the opening (of doors, etc.) are 55.1 inches (W) and 66.9 inches (H).
Electric current consumption
MAX. 4.7 A (AC 120 V 60 Hz) MAX. 2.6 A (AC 220 V 50 Hz) MAX. 2.5 A (AC 220 V 60 Hz) MAX. 2.5 A (AC 230 V 50 Hz) MAX. 2.4 A (AC 240 V 50 Hz)

FIG. 2

3. OPERATION
PRECAUTIONS TO BE HEEDED BEFORE STARTING THE OPERATION To avoid injury and trouble, be sure to constantly give careful attention to the behavior and manner of the visitors and players.
In order to avoid accidents, check the following before starting the operation:
To ensure maximum safety for the players and the customers, ensure that where the product is operated has sufficient lighting to allow any warnings to be read. Operation under insufficient lighting can cause bodily contact with each other, hitting accident, and or trouble between customers. Be sure to perform appropriate adjustment of the monitor (projector). For operation of this machine, do not leave monitor's flickering or deviation as is. Failure to observe this can have a bad influence upon the players' or the customers' physical conditions. It is suggested to ensure a space allowing the players who feel sick while playing the game to take a rest. Check if all of the adjusters are in contact with the surface. If they are not, the Cabinet can move and cause an accident.
Ensure that all of theAdjusters are in contactwith the floor.
Perform a test run and confirm whether the surfboard is locks and unlocks properly. Be sure to take particular care to conduct the Sensor Mat input test. Failing to conduct the test and operating the machine when the Sensor Mat is not in optimum condition may cause accidents.
Are there side window breaks or omissions?
Does the surfboard lock and unlock properly?
Is the sensor of the Sensor Mat operating correctly? Are the handrails loose? Are there any tears in the bellows?
Do not put any heavy item on this product. Placing any heavy item on the product can cause a falling down accident or parts damage. Do not climb on the product. Climbing on the product can cause falling down accidents. To check the top portion of the product, use a step. To avoid electric shock, check to see if door & cover parts are damaged or omitted. To avoid electric shock, short circuit and or parts damage, do not put the following items on or in the periphery of the product. Flower vases, flowerpots, cups, water tanks, cosmetics, and receptacles/ containers/vessels containing chemicals and water.

PHOTO 6. 1 b

Assemble the hole lid and the front lid under the front lid. When facing the PTV screen, the hole lid is to the right and the front lid is to the left. Five truss screws secure the hole lid and four truss screws secure the front lid.

PHOTO 6. 1 c

Have three or more persons use the platform when performing the following operations. Set the billboard on top of the PTV top panel. wire connector into the terminal board of the PTV top panel.
10 While 2 people hold the Billboard by, a third person using a step should connect the Billboard 11 Insert the Billboard into the holder bracket, fix to PTV with the 2 screws.
SCREW (2) black M516,w/flat & spring washers
For performing work, use 3 workers.
FIG. 6. 1 d Connect the Connector.

FIG. 6. 1 e

When performing work, be sure to use a step.

FIG. 6. 1 f

WIRING CONNECTIONS BETWEEN THE CABINETS With the ASSY Tube installed to the Front and Rear Cabinets, perform the cabinet-to-cabinet wiring. The connectors can be inserted only into those with the same number of pins, respectively, and can be inserted only in the fixed orientation. If you attempt to apply constrained force when inserting the connector, the connector or wiring may be damaged. Fully make sure that it is in the correct orientation.

Rear Cabinet Side

Bring the six wiring connectors and the ground out from the rear cabinet. Be careful not to trip over the wires as this may cause injury. There is a stud to secure the ground to the Assy Tube lid. Tighten the hexagon nut to this stud with the circular ground line terminal, the flat washer and the spring washer in that order.
GROUND LINE HEXAGON NUT (1) M4,flat & spring washers used.

TUBE LID

PHOTO 6. 2 a Secure the ground terminal.
Join the connector of the Assy Tube to the connector of the Rear Cabinet. Join the connectors to those with the same number of pins.

Billboard's fluorescent lamp Always lit On-screen images are outputted.

Sound is emitted.

Start button

Surfboard Lock

Cold-Cathode Tube On/Off

FIG. 6. 5

ASSEMBLING CHECK In the TEST MODE, ascertain that the assembly has been made correctly and IC BD. is satisfactory (refer to Section 9). In the test mode, perform the following test:
1 MEMORY TEST Selecting the RAM TEST on the system test mode menu screen causes the on-board memory to be tested automatically. The game board is satisfactory if the display beside each IC No. shows GOOD.
RAM TEST IC 29 GOOD IC 35 GOOD IC 09 GOOD IC 10 GOOD IC 11 GOOD IC 12 GOOD IC 16 GOOD IC 18 GOOD IC 20 GOOD IC 22 GOOD IC 17 GOOD IC 19 GOOD IC 21 GOOD IC 23 GOOD IC106 GOOD IC107 GOOD IC108 GOOD IC109 GOOD IC111 GOOD IC113 GOOD IC115 GOOD IC117 GOOD IC112 GOOD IC114 GOOD IC116 GOOD IC118 GOOD PRESS TEST BUTTON TO EXIT
GAME ROM TEST [] NO. TYPE RESULT BYTE WORD IC22 32M ---- IC1 64M GOOD IC2 64M GOOD IC3 64M GOOD IC4 64M GOOD IC5 64M GOOD IC6 64M GOOD IC7 64M GOOD IC8 64M GOOD IC9 64M GOOD IC10 64M GOOD : IC21 64M GOOD PRESS TEST BUTTON TO EXIT
2 C.R.T. TEST In the system test mode menu, selecting C.R.T. TEST allows the screen (on which the monitor is tested) to be displayed. Although the monitor adjustments have been made at the time of shipment from the factory, color deviation, etc., may occur due to the effect caused by geomagnetism, the location building's steel frames and other game machines in the periphery. By watching the test mode screen, make judgment as to whether an adjustment is needed. If it is necessary, adjust the monitor by referring to Section 11.
C.R.T. TEST 1/RED GREEN BLUE WHITE PRESS TEST BUTTON TO CONTINUE
PRESS TEST BUTTON TO EXIT C.R.T. TEST 2/2
3 SOUND TEST In the system test mode, selecting SOUND TEST causes the screen (on which sound related BD and wiring connections are tested) to be displayed. Check if the sound is satisfactorily emitted from each speaker and the sound volume is appropriate.
SOUND TEST RIGHT SPEAKER OFF LEFT SPEAKER OFF -> EXIT
SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

4 INPUT TEST

INPUT TEST START OFF LEFT BUTTON OFF RIGHT BUTTON OFF BOARD SWING 82H BOARD ROLL 83H BOARD PITCH 9AH SENSOR MAT OFF SERVICE OFF TEST OFF
Selecting the INPUT TEST on the game test mode menu screen causes the screen (on which each switch is tested) to be displayed. Press each switch. If the display beside each switch indicates "ON," the switch and wiring connections are satisfactory.

REFERENCE SECTIONS 9-3D, E 9-3B 9-3C SERVICE MANUAL SERVICE MANUAL

MEMORY

PERIODIC SERVICING
SERVICE MANUAL 9-3D, E 9-3B 9-3C

CONTROL SYSTEM

9-3B 9-3E, SERVICE MANUAL 11 SERVICE MANUAL SERVICE MANUAL SERVICE MANUAL 9-3F
MONITOR IC BOARD DATA CHECK
9 - 1 SWITCH UNIT AND COIN METER
Adjust the sound to the optimum volume, taking into consideration the environmental requirements of the installation location. If the COIN METER and the game board are electrically disconnected, game play is not possible.
SWITCH UNIT Open the coin chute door, and the switch unit shown will appear. The functioning of each SW is as follows:

SPEAKER

SUPER WOOFER

SERVICE

FIG. 9. 1 a SWITCH UNIT

(SPEAKER)

SOUND VOLUM
:Adjusts the sound volume of the left and right speakers on the control panel.
2 WOOFER VOLUME :Adjust the sound output of the super woofer.

(SUPER WOOFER) (TEST)

3 TEST BUTTON 4 SERVICE BUTTON

(SERVICE)

:For the handling of the TEST button, refer to the following pages. :Gives credits without registering on the coin meter.
COIN METER Open the Cashbox Door by using the key to have the Coin Meter appear underneath the Cashbox.

COIN METERS

PHOTO. 9. 1 b COIN METER

9 - 2 SYSTEM TEST MODE

The contents of settings changed in the TEST mode are stored when the test mode is finished from EXIT in the menu mode. If the power is turned off before the TEST mode is finished, the contents of setting change become ineffective. Executing "BACKUP DATA CLEAR" in the SYSTEM TEST MODE does not clear the BOOKKEEPING data in the GAME TEST mode. Entering the TEST mode clears fractional number of coins less than one credit and BONUS ADDER data. Perform setting as per specified in this manual for operation. If setting not specified is performed for operation, proper function of this product may not be obtained.

TAIL LID

Remove the three screws from each of the bellows sashes and remove the sashes from the left and right of the surfboard.

PHOTO 10. 2 d

SCREW (3 each), black M48, w/flat & spring washers

BELLOWS SASH

PHOTO 10. 2 e
Lift the bellows to be able to see the ROLL VR unit. Loosen the two screws that secure the ROLL VR unit and adjust the gear engagement. When the surfboard is level to the ground, engage the gears so that the D-cut face of the volume axle is arranged as shown in Figure 10.2.

FIG. 10. 2

PHOTO 10. 2 f
SCREW (2), black M48, w/flat & spring washers
Tighten the two loosened screws after performing the adjustment. Turn on the power and perform CALIBRATION in TEST MODE. (Refer to 9-3 E.) Check the volume values. Be sure to confirm that they are within the recommended value range and that they change smoothly in line with operation. (Refer to 9-3 B.) Attach the bellows sashes and tail lids after checking.
Perform the operations listed in "Adjustments" 1 through 6, listed above. Loosen the harness lug that secures the wiring and remove the connector from the bottom right side of the surfboard.

CONNECTOR (1)

PHOTO 10. 2 g
Remove the two screws and remove the ROLL VR unit.

PHOTO 10. 2 h

Loosen the two hexagon socket screws that secure the gears and remove the gears from the volume axle.
HEXGAON SOCKET SCREW (2) M36

PHOTO 10. 2 i

Remove the hexagon nuts that secure the volume to the VR bracket and remove it from the VR bracket.

PHOTO 10. 2 j

The wiring attached to the volumes is used as is. Cut the connection areas with the nippers. Remove the old heat-shrinkable tube from the wiring. Remove the coating from the wire tips with the wire strippers. Expose about five millimeters of conducting wire. ( See PHOTO 10. 1 j ) Pass each of the included heat-shrinkable tubes through to the wiring. ( See PHOTO 10. 1 k ) and be careful not to solder the wrong wires. ( See PHOTO 10. 1 l )
10 Solder the wires to the terminal posts of the volumes to be replaced. Check the wiring diagram 11 Heat the heat-shrinkable tubes with the industrial dryer and weld so that the heat-shrinkable tube
covers the welding area. ( See PHOTO 10. 1 m )
12 Attach the volume to the VR bracket and secure the gears to the volume axles. 13 Install the ROLL VR unit. At this time, assemble it so that the gears engage as explained in
"Adjustments" 6 and 7, listed above. Secure the wiring with harness lugs after connecting the connector.
14 Perform the operations listed in "Adjustments" 8 and 9, listed above and confirm that the

replaced volume functions normally. In addition, be especially careful not to damage the wiring with the interior constituent parts.
15 After confirmation, attach the two bellows sashes and the tail lid.
10 - 3 PITCH DETECTION VOLUME REPLACEMENT The surfboard's PITCH detection volume is located to the interior of the bellows under the surfboard to the rear. The following tools are required for the operations below: an M4 screw Phillips screwdriver, a hexagonal wrench with an opposite side distance of 1.5 millimeters, an adjustable spanner with an opposite side distance of 10 to 11 millimeters, nippers, cutters, a wire stripper, a soldering iron and an industrial dryer. There is no gear engagement adjustment for the PITCH detection volume. Attach the VR guide to the volume axle at an angle such that the tips of the screws that secure the VR guide touch the volume axle D cut face. To avoid the possibility of damage to the volume or poor operation, attach them so that the VR guide moves smoothly in line with the movement of the constituent parts pin. REPLACING PROCEDURE
Perform 10-2 operations 1 through 5. Lift the bellows to be able to see the PITCH VR unit. Loosen the harness lug that secures the wiring and remove the connector from the bottom right side of the surfboard.

PHOTO 10. 3 a

Remove the two screws and remove the PITCH VR unit.

PHOTO 10. 3 b

Loosen the two hexagon socket screws that secure the VR guide and remove the VR guide from the volume axle.

PHOTO 10. 3 c

Remove the hexagon nuts that secure the volume to the VR bracket and remove the VR bracket.

PHOTO 10. 3 d

The wiring attached to the volumes is used as is. Cut the connection areas with the nippers. Remove the old heat-shrinkable tube from the wiring. Remove the coating from the wire tips with the wire strippers. Expose about five millimeters of conducting wire. ( See PHOTO 10. 1 j ) Pass each of the included heat-shrinkable tubes through to the wiring. ( See PHOTO 10. 1 k ) Solder the wires to the terminal posts of the volumes to be replaced. Check the wiring diagram and be careful not to solder the wrong wires. ( See PHOTO 10. 1 l ) covers the welding area. ( See PHOTO 10. 1 m )
11 Heat the heat-shrinkable tubes with the industrial dryer and weld so that the heat-shrinkable tube
12 PAttach the PITCH VR unit so that the pin is
inserted into the VR guide notch. Connect the connectors and secure the wiring with the two harness lugs.

PHOTO 10. 3 e

13 Turn on the power and perform calibration in TEST MODE. (Refer to 9-3 E.)
At this time, be especially careful that the VR guide rotates smoothly in line with operation and that the interior constituent parts will not damage the wiring.

Turn off the power. Remove the tail lid from the back surface of the surfboard. (Refer to 10-2, 2 through 4.)

PHOTO 10. 5 a

Remove the bellows sashes from the left and right of the surfboard. (Refer to 10-2, 5.)

BELLOWS SASHE

PHOTO 10. 5 b
Remove the nose lid from the front of the surfboard. Remove the two screws.

NOSE LID

PHOTO 10. 5 c

PHOTO 10. 5 d

Remove the eight hexagon nuts from the bottom of the surfboard. This is the pairing of the carriage bolts and hexagon nuts other than for the two areas to the front of the surfboard.
CARRIAGE BOLT (chrome plated) & HEXAGON NUT (6 each) M630, flat washer used.
Tow carriage bolts are fixed to the board cover.
HEXAGON NUT (2) M6, flat washer used.

PHOTO 10. 5 e

PHOTO 10. 5 f
Remove the surfboard by lifting it straight up.

PHOTO 10. 5 g

Remove each pair of hexagon-head bolts and remove the two board holders.

BOARD HOLDER

PHOTO 10. 5 h

PHOTO 10. 5 i

HEXAGON-HEAD BOLT (2 each) M830, w/spring washer
Remove the ASSY board from the SWING mechanism. The bellows are attached below the wooden board of the ASSY board.

ASSY BOARD

PHOTO 10. 5 j

BELLOWS

PHOTO 10. 5 k
Remove each set of three screws and remove the left and right bellows holder sides.
SCREW (3 each) M416, w/flat & spring washers

PHOTO 10. 5 l

BELLOWS HOLDER SIDE

PHOTO 10. 5 m

10 Remove each pair of screws and remove the front and back bellows holders.

PHOTO 10. 5 n

SCREW (2 each) M416, w/flat & spring washers

BELLOWS HOLDER

Remove and replace the damaged bellows. Attach the bellows "seam" to the wooden board so that comes to the front. Attach and secure the pair of bellows holder sides and the pair of bellows holders that were removed in the previous steps.

PHOTO 10. 5 o

BELLOWS SSF-3405

"SEAM"

PHOTO 10. 5 p

The cross pattern moves up/down and right/left to start the movement of searching the correct screen position and inclination.
When the green cross pattern movements are finished, similar detection is performed sequentially in order of red and then blue cross movements. After detecting by green, red and blue cross movements, the game mode returns with the color deviation status being corrected. Although very rarely, the TRY AGAIN error display in red may appear. At this time, press the P button (red) for approximately 3 seconds. Even after the above operation is repeated, if the error condition still exists, then the display shifts to PLEASE ADJ. In this case, the auto color matching function can not be used. Contact the place of contact herein stated or where the product was purchased from. If the automatic color matching indicates an error, color matching can manually be performed. Refer to CONVERGENCE ADJUSTMENT (manual color matching).
ADJUSTING THE ON-SCREEN CONTRAST Although the on-screen picture quality has been adjusted at the time of shipment from the factory, the on-screen contrast can be readjusted if desired. When the Game Board is replaced, readjustment may be necessary. Changing the CONTRAST causes the light and shade of the on-screen images to be changed. 1 Press either or PIC - ADJ button.
CONTRAST BRIGHTNESS H.POSI V.POSI H.SIZE V.SIZE EXIT
The on-screen menu will have one item in purple and 6 items in white.
2 Choose CONTRAST by using either or PIC
Herein, procedure 2 is skipped. - ADJ button.
Have CONTRAST displayed in purple. Since CONTRAST is selected initially, no particular operation is required in this case.
3 Press the SET button (to decide selection).
When the selection of the CONTRAST adjustment mode is decided, the adjustment data scale bar appears on the screen.

CONTRAST 230.

4 Make adjustment by using either

button.

As the Cursor is moved, the adjustment data value changes. Make adjustment so as to obtain the desired on-screen contrast status.

CONTRAST 156.

5 Press the WRITING button (for storing and finish).
The WRITING display appears and the adjustment data is stored.
When discontinuing the adjustment, choose EXIT from the menu at the stage of procedure 2 and press

the SET button.

To continue adjusting other menu items, repeat procedure 2 ~ 4. Unless the adjustment data is stored, the data in the adjusted status will be erased at the time the power is
turned off and the pre-adjustment status will remain when the power is turned on next time.
ADJUSTING THE SCREEN BRIGHTNESS Although the on-screen picture quality has been adjusted at the time of shipment from the factory, readjustment can be made if desired. When the Game Board is replaced, readjustment may be necessary. Changing the BRIGHTNESS causes the brightness of the on-screen images of black portions to be changed.

In order to prevent electric shock and short circuit hazards, be sure to turn power off before performing work. Be careful so as not to damage wirings. Damaged wiring can cause fire, electric shock and short circuit hazards. Do not expose the Game BD, etc. without a good reason. Failure to observe this can cause electric shock hazard or malfunctioning.
The electronic parts on the IC Board could be damaged due to human body's static electricity. Before performing IC Board related work, be sure to discharge physically accumulated statics by touching grounded metallic surfaces, etc. Removing the screws that secure the game board may cause it to fall and become damaged. Be sure to support the board carefully when removing the securing screws.
Put the Game Board in the Carton Box (an accessory) together with the Shield Case when requesting for the replacement or repair. Transporting the Game Board in an undesignated status for replacement/repair is unacceptable.
16 - 1 REMOVING THE GAME BOARD The Game Board and all the other IC boards are located on the back of the Front Cabinet.
Turn the power off. Remove the 2 truss screws securing the Back Door.
TRUSS SCREW (2), black M420

PHOTO 16. 1 a

Unlock and remove the Back Door.

PHOTO 16. 1 b

There is a game board (NAOMI 2 Board) above the wooden board of the ASSY MAIN board to the interior of the back door. Disconnect all of the connectors that are connected to the game board. If the connectors are difficult to disconnect because of how they are secured, unsecure them before removing.

PHOTO 16. 1 c

Remove the four screws that secure the wooden board of the game board and remove the game board. When removing the securing screws the game board may fall and damage the game board or its interior part and wiring. Support the board carefully when removing the screws.
SCREW (4) M416, w/flat & spring washers

GAME BOARD

PHOTO 16. 1 d
16 - 2 COMPOSITION OF GAME BOARD ASSY CASE NAT SSF USA 840-0095D-01 USA
TRUSS SCREW (4) M330,chrome plated
ROM CASE NAT SSF 840-0095C

DIP SW

ASSY CASE NAOMI2 MAIN BD USA / 840-0046A-01 : USA

FIG. 16. 2 a

DIP SW SETTING In this product, set all of the DIP SWes to OFF.

FIG. 16. 2 b

17. DESIGN RELATED PARTS

5 ASSY SUBCABI FRONT (SSF-1001)

Opposite side:

ITEM NO. PART NO. SSF-1002 SSF-1030 ATR-1050 ATR-1060 ATR-1070 ASK-1152 ARC-1006 117-5233 253-5460-01 117-5402-06-91 SSF-1003 SSF-1004 SSF-1005 601-9377 601-5699X 280-5009-01 280-0419 000-P00420-W 000-T00416-0B 000-P00416-W 000-T00420-0B 030-000630-SB 011-F00316 030-000625-W 050-H01600-0B 011-F00312 011-T03512 600-6972-1200 SSF-6002 SSF-60001 SSF-60014 SSF-60015 DESCRIPTION BASE CABINET ASSY WOOFER AC UNIT FAN UNIT ASSY BACK DOOR LOCK BRKT LEG BRACKET PLATE LEG BRACKET BLACK AIR VENT BLACK EARTH TERMINAL PLATE 6P WOOFER NET STICKER PTV LOWER L STICKER PTV LOWER R CASTER FAI=75 LEG ADJUSTER BOLT M1675 CORD CLAMP 21 HARNESS LUG M SCR PH W/FS M420 M SCR TH BLK M416 M SCR PH W/FS M416 M SCR TH BLK M420 HEX BLT BLK W/S M630 TAP SCR FH 316 HEX BLT W/FS M625 HEX NUT BLK M16 TAP SCR #1 FH 312 TAP SCR TH 3.512 WIRE HARN EARTH ID5 1200MM ASSY WIRE FRONT DC WH XFMR IN WH PTV AC100V WH AC FAN NOTE

6 ASSY WOOFER (SSF-1030)

PART NO. SSF-1031 130-5097 209-0023 011-T03512 SSF-60029
DESCRIPTION WOOFER BRKT SPEAKER BOX SUPER WOOFER CONN CLOSED END TAP SCR TH 3.512 WH WOOFER

7 AC UNIT

ITEM NO. 104
PART NO. JBA-1031 421-7468-01 214-0202 512-5046-8000 512-5046-5000 509-5453-91-V-B
DESCRIPTION AC BRKT STICKER C.P W/PIC AC INLET PANEL TYPE C.P 8000MA CE UL C.P 5000MA CE UL SW ROCKER J8 V-B
<AC 110-120V Area> <AC 220-240V Area>

8 FAN UNIT (ATR-1060)

Connector

ITEM NO. 102 201

PART NO. ATR-1061 260-0011-02 601-8543 000-P00312-W
DESCRIPTION FAN BRKT AXIAL FLOW FAN AC100V 50-60HZ FAN GUARD M SCR PH W/FS M312
9 ASSY BACK DOOR (ATR-1070)

ITEM NO. 201

PART NO. ATR-1071 TH-1015 253-5460-01 220-5575 000-T00408-0B
DESCRIPTION BACK DOOR LOCKING TONGUE AIR VENT BLACK CAM LOCK MASTER W/O KEY M SCR TH BLK M48
10 ASSY WIRE FRONT DC (SSF-6002)
This is comprised of the following wire harnesses. ASSY drawing is not available.

ITEM NO. 308

PART NO. 601-0460 SSF-60016 SSF-60023 SSF-60024 SSF-60025 SSF-60026 SSF-60027 SSF-60028 600-7009-2500
DESCRIPTION PLASTIC TIE BELT 100 MM WH EXT WOOFER WH EXT SOUND FRONT WH EXT TOWER FRONT WH EXT SW FRONT WH EXT LAMP FRONT WH EXT BRAKE FRONT WH EXT VR FRONT ASSY RGB CA D-SUB 15P 2500MM
11 ASSY MAIN BD (SSF-4000)
Note: Do not wire across the diagonal lines.
ITEM NO. 314 PART NO. SSF-4001 APC-4002 840-0095D-01 837-13551-92 839-1073-03 400-5397-01 400-5421-03024 400-5421-05012 560-5407 610-0609 601-7467 / / / 838-11856-UL 838-13616 000-P00308-W 000-P00408-W 000-P00416-W 011-P00325 011-T03516 011-T03512 011-F00312 600-7141-100 600-7159-070 ATR-60004 ATR-60012 SSF-60004 SSF-60005 SSF-60006 SSF-60007 SSF-60008 SSF-60009 SSF-60010 SSF-60011 SSF-60012 SSF-60013 DESCRIPTION MAIN BD BASE SW REGU BRKT ASSY CASE NAT SSF USA I/O CONTROL BD FOR JVS SSR BD 1 DC 2A SW REGU FOR JVS VA SW REGU LCA30S-24 SW REGU LCA50S-12 AUDIO XFMR 100V 17V2.1AX2 LOWPASS AMP 4OHM 30W L-LOCK BK NOTE

<Others> <USA>

16 ASSY MASK (MGL-1150)

ITEM NO. 202
PART NO. MGL-1102 MGL-1151 MGL-1152 012-F00408-0B 000-F00410
DESCRIPTION TV MASK SLIT PLATE MASK SIDE HOLDER TAP SCR FH BLK 48 M SCR FH M410
17 ASSY FRONT PANEL (ATR-1300)
ITEM NO. PART NO. ATR-1301 ATR-1302 EZT-0603 EZT-0604 ATR-1303 440-WS0002XEG 000-T00420-0B 068-441616-0B 050-F00500 068-552016 DESCRIPTION FRONT PANEL FRONT LID SIDE BRKT BRKT UPPER BRKT LOWER STICKER W POWER OFF ENG M SCR TH BLK M420 FLT WSHR BLK 4.4-161.6 FLG NUT M5 FLT WSHR 5.5-20 1.6 NOTE
: the state before attachment. 222 : Outside of the cabinet. Fastening Torque 228 : 8.33 N m (85 kgf cm)
18 ASSY REAR CABI (SSF-3000)
ITEM NO. 25 25A 25B 25C PART NO. SSF-3100 / SSF-3580 SSF-3600 SSF-3650 / SSF-3700 SSF-3750 SSF-3001 SSF-3002 SSF-3003 SSF-3004 SSF-3005 SSF-3006 SSF-3007 SSF-3008 SSF-3009 SSF-3010 SSF-3011 SSF-3012 SSF-3013 SSF-3014 SSF-3015 SSF-3016 SSF-3017 SSF-3017-A SSF-3017-B SSF-3017-C ATR-3008 SSF-3018 SSF-3019 SSF-3020 SSF-3021 SSF-3022 SSF-3023 SSF-3024 SSF-3025 SSF-3026 SSF-3027 SSF-3028 SSF-3029 SSF-3030 421-11416 440-WS0166-EG 440-WS0047-EG 280-5009-01 DESCRIPTION ASSY REAR BASE COIN TOWER (HAPP CONTROLS) ASSY CONTROL PANEL ASSY SIDE WALL L ASSY SIDE WALL R LAMP UNIT ASSY SPEAKER L ASSY SPEAKER R CABINET LIB TOWER BASE BACK DOOR VOLUME LID SWING ARM PLATE FRAME SUPPORT BRKT A L FRAME SUPPORT BRKT A R FRAME SUPPORT BRKT B WALL SUPPORT PLATE CUSHION SPONGE LOWER COVER SUPPORT SIDE WINDOW L SIDE WINDOW R INNER SASH A INNER SASH B INNER SASH C PIPE FRAME PIPE FRAME BLANK CUSHION TUBE CENTER CUSHION TUBE SIDE PIPE SUPPORT BRKT PIPE HOLDER L PIPE HOLDER R SIDE COVER L A SIDE COVER L B SIDE COVER L C SIDE COVER R A SIDE COVER R B SIDE COVER R C LAMP COVER WIRE LID CONTROL PANEL HOLDER WINDOW OUTER SASH STICKER BOX LOWER STICKER CAUTION FORK STICKER W HI VOLT M ENG STICKER W FINGER GEAR ENG CORD CLAMP 21 NOTE
ITEM NO. 231 PART NO. 030-000630-SB 068-652016-0B 030-000820-S 060-F00800 000-T00416-0C 068-441616-0C FAS-300032 068-852216 FAS-300008 068-852216-0C 030-000845-S 030-000616-SB 060-F00600-0B FAS-300029 FAS-300033 060-S00600 000-T00410-0B 000-P00416-W FAS-310004 050-H00800 060-S00800 060-T00416-0B 000-T00420-0B 068-441616-0B 008-B00820-0C 031-000650-0C 069-0140 059-0082 030-000880-S 000-F00312 FAS-000083 DESCRIPTION HEX BLT BLK W/S M630 FLT WSHR BLK 6.5-201.6 HEX BLT W/S M820 FLT WSHR M8 M SCR TH CRM M416 FLT WSHR CRM 4.4-161.6 HEX BLT BLK M8110 FLT WSHR 8.5-22 1.6 HEX BLT W/S CRM M850 FLAT WSHR CRM 8.5-221.6 HEX BLT W/S M845 HEX BLT W/S BLK M616 FLT WSHR BLK M6 HEX BLT W/S M660 HEX BLT M680 SPR WSHR M6 M SCR TH BLK M410 M SCR PH W/FS M416 CRG BLT BLK M890 HEX NUT M8 SPR WSHR M8 M SCR TH BLK M416 M SCR TH BLK M420 FLT WSHR BLK 4.4-161.6 TMP PRF SCR BH CRM M820 CRG BLT CRM M650 FLT WSHR NI M6 CUP NUT TYPE 3 CRM M6 HEX BLT W/S M880 M SCR FH M312 M SCR TH BLK M422 NOTE

23 SWING VR UNIT (SSF-3160)

D cut direction

Note: Apply greasing to the gear portion.
ITEM NO. 301 PART NO. SSF-3161 SSF-3162 SSF-3163 SSF-3164 601-8966 601-6959 601-7945 220-5484 220-5753 100-5257 310-5029-F20 065-E00500 000-P00408-W 000-P00416-W 028-A00306-P SSF-60051 DESCRIPTION SWING VR BRKT SWING VR PIN SWING VR PLATE SWING VR GUIDE GEAR HOLDER GEAR 64 GEAR 20 VOL CONT B-5K OHM VOL CONT B-5K OHM BEARING FAI6 SUMITUBE F F 20MM E RING 5MM M SCR PH W/FS M48 M SCR PH W/FS M416 SET SCR HEX SKT CUP P M36 WH SWING VR NOTE
24 ROLL VR UNIT (SSF-3170)

ITEM NO. 201 301

PART NO. SSF-3171 601-7944 220-5484 220-5753 310-5029-F20 028-A00306-P SSF-60052
DESCRIPTION ROLL VR BRKT GEAR 15 VOL CONT B-5K OHM VOL CONT B-5K OHM SUMITUBE F F 20MM SET SCR HEX SKT CUP P M36 WH ROLL VR
25 PITCH VR UNIT (SSF-3180)

ITEM NO. 202 301

PART NO. SSF-3181 SSF-3182 SSF-3183 220-5484 220-5753 310-5029-F12 000-P00410-W 028-A00306-P SSF-60053
DESCRIPTION PITCH VR BRKT PITCH VR GUIDE PITCH VR HOLDER VOL CONT B-5K OHM VOL CONT B-5K OHM SUMITUBE F F 12MM M SCR PH W/FS M410 SET SCR HEX SKT CUP P M36 WH PITCH VR
26 ASSY TALE COVER (SSF-3190)
PART NO. SSF-3191 SSF-3192 280-6622-50040 050-U00400 068-441616-0B
DESCRIPTION TALE LID CUSHION RUBBER TALE SPACER TUBE U NUT M4 FLT WSHR BLK 4.4-161.6
27 ASSY SWING MECHA (SSF-3200)

GREASE ALBANIA

Notes: 1. Apply greasing to the gear portion. 2. Apply greasing. (Grease Albania: Showa Shell Sekiyu)
ITEM NO. PART NO. SSF-3230 SSF-3250 SSF-3270 SSF-3201 SSF-3202 SSF-3203 280-5169 280-0419 FAS-200005 FAS-200026 060-S01400 030-001025-S 060-F01000 060-S01000 050-H01000 FAS-300034 000-P00408-W 000-P00408 060-S00400 060-F00400 050-F00400 050-H00400 SSF-60041 SSF-60042 SSF-60043 600-6972-0850 DESCRIPTION ASSY ROSTA ASSY BRAKE ASSY GEAR SWING FRAME SWING BASE WIRE GUARD CORD CLAMP TL-20S HARNESS LUG HEX SKT H CAP SCR B 0Z M1440 HEX SKT CAP SCR BLK OZ M1450 SPR WSHR M14 HEX BLT W/S M1025 FLT WSHR M10 SPR WSHR M10 HEX NUT M10 HEX BLT W/S M1230 M SCR PH W/FS M48 M SCR PH M48 SPR WSHR M4 FLT WSHR M4 FLG NUT M4 HEX NUT M4 WH EXT BRAKE REAR B WH EXT SWING VR WH EXT MECHA VR WIRE HARN EARTH ID5 0850MM NOTE

28 ASSY ROSTA (SSF-3230)

ITEM NO. 207 PART NO. SSF-3231 SSF-3232 SSF-3233 SSF-3234 SSF-3235 SSF-3236 SSF-3237 601-11147 111-0049 111-1133 FAS-200018 060-S01200 050-H01600 060-S01600 FAS-500034 030-001025-S 060-F01000 DESCRIPTION SWING ROSTA ARM UPPER SWING ROSTA ARM LOWER SWING ARM PIN ARM PIN COLLAR SWING LINK SHAFT SWING ROSTA BASE SWING ROSTA HOLDER ROSTA DR-S-3880 ROD END 16 (POS 16) ROD END 16 (POS 16 L) HEX SKT CAP SCR BLK 0Z M1285 SPR WSHR M12 HEX NUT M16 SPR WSHR M16 HEX NUT L M16 HEX BLT W/S M1025 FLT WSHR M10 NOTE

29 ASSY BRAKE (SSF-3250)

ITEM NO. 203
PART NO. ATR-3350 SSF-3251 601-5962-094 280-0419 030-000820-S 060-F00800 050-F00400
DESCRIPTION BRAKE UNIT BRAKE BASE BUSH 3.2T HARNESS LUG HEX BLT W/S M820 FLT WSHR M8 FLG NUT M4

30 BRAKE UNIT (ATR-3350)

Fastening Torque: M5: 3.7N m M4: 1.8N m

ITEM NO. 204 205

PART NO. ATR-3351 ASL-3352 ATR-3353 ASL-3354 ASK-3606 601-10806 100-5229 020-000530-0Z 060-S00500 065-S014S0-Z 065-A030H0-Z 028-A00408-P
DESCRIPTION BRAKE BASE PINION GEAR 25 BRAKE SHAFT KEY 5524 KEY 55-10.5 BRAKE BXH-08 BEARING 17 HEX SKT H CAP SCR BLK OZ M530 SPR WSHR M5 STP RING BLK 0Z S14 STP RING BLK 0Z H30 SET SCR HEX SKT CUP P M48

31 ASSY GEAR (SSF-3270)

ITEM NO. 201 202
PART NO. SSF-3271 SSF-3272 020-001020-0Z 060-S01000
DESCRIPTION SWING GEAR HOLDER SWING GEAR HEX SKT CAP SCR BLK 0Z M1020 SPR WSHR M10
32 ASSY BOARD MECHA (SSF-3300)
PART NO. SSF-3330 SSF-3350 SSF-3301 020-001020-0Z 060-S01000 060-F01000 030-000820-S 060-F00800
DESCRIPTION ASSY ROLL SHAFT ASSY PITCH BASE ROLL ROSTA HOLDER HEX SKT CAP SCR BLK 0Z M1020 SPR WSHR M10 FLT WSHR M10 HEX BLT W/S M820 FLT WSHR M8
33 ASSY ROLL SHAFT (SSF-3330)

Fastening Torque: 77 N m

ITEM NO. PART NO. SSF-3331 SSF-3332 SSF-3333 SSF-3334 ASL-3251 601-6450 100-5410 601-8458 050-H01200 060-S01200 028-A00408-P 000-P00410-W DESCRIPTION ROLL SHAFT ROLL SHAFT COLLAR FLT WSHR 12.5-303.2 GEAR HOLDER 110 MOUNT BLOCK GEAR 110 BEARING UNIT 20 ROSTA 22 DR-S27100 HEX NUT M12 SPR WSHR M12 SET SCR HEX SKT CUP P M48 M SCR PH W/FS M410 NOTE
34 ASSY PITCH BASE (SSF-3350)

Use the nuts included.

PART NO. SSF-3351 SSF-3352 SSF-3353 SSF-3354 601-11146
DESCRIPTION PITCH BASE ROLL STOPPER BRKT PITCH STOPPER HOLDER PITCH STOPPER RUBBER STOPPER RUBBER RI-45HD L=19.1
030-000820-S 060-F00800 030-000612-S 060-F00600 000-P00408 060-S00400 060-F00400
HEX BLT W/S M820 FLT WSHR M8 HEX BLT W/S M612 FLT WSHR M6 M SCR PH M48 SPR WSHR M4 FLT WSHR M4

onic the Hedgehog, 20th Anniversary Page 1

irque de Solei Page 1

uran Burning Page 1
oul Surfers Review Page 1

uckerpunch Review Page 2

on Iver Page 2

Conn vs. Butler Page 3

By Nick Pruett Staff Writer

The Lions Roar

Visit us online at www.the-lions-roar.com

Friday, April 15, 2011

Liberty High School, Brentwood CA
Sonic the Hedgehog: 20th Anniversary Retrospec tive
Twenty years ago, an icon that changed the face of gaming forever was born: Sonic the Hedgehog. Over the years, he has been known as a mascot for Sega and has starred in a series that is not like your average video game. He has been going through hill, ramps, and loops at highspeeds, collecting gold rings and foiling Dr. Robotnik's master plans to take over the world. Not only has he been in games, but also a few TV shows and a comic book series! When youre playing the games, it feels like you are in the game getting an adrenaline rush from the speed! -Jacqueline Nares (10). We will take a look at how he has come and gone over the last 20 years!
The Genesis Era (1991-1996) In 1991, Sonic the Hedgehog was released on the Sega Genesis and was really well received by critics. It was praised for the different platforming elements, such as the sense of speed, and was considered one of the greatest games of all time. The success spawned a sequel titled Sonic the Hedgehog 2 on the Genesis, in 1992. Like its predecessor, it received positive reviews from critics, praising the larger levels, diverse cast of characters, colorful graphics, and the addition of two-player game play, and being one of the bestselling Sega Genesis games of all time. Sonic the Hedgehog 2 was the first Sonic game I have played and liked! -Luke Jung (10). In 1994, Sonic the Hedgehog 3 and Sonic and Knuckles were released on the Genesis

Sonic cont. on Page 2

Quran Burning
By Michael Najera Staff Writer
Tension brews in the Middle East as Terry Jones, Pastor of the Dove World Outreach Center in Gainesville, Florida, burns a holy Muslim bible, the Qur'an, on March 20th, 2011 in the name of free speech.
Currently 11 countries are condemning Pastor Terry Jones. In Kandahar, Afghanistan, 22 people were reported killed during the outcry and protesting of seeing a man in Florida burning their bible. It also lead an attack on a United Nations compound in which insurgents fired assault rifle and explosives that ended
with seven UN employees dead on the scene. President Obama says the act of disgrace towards a selected religion "is an act of extreme intolerance." The White House summary reads: "The two [U.S. and Afghan] presidents were clear that to attack and kill innocent people is an affront to human decency and dignity." General David Petraeus, leader of 150,000 U.S. and allied troops in Afghanistan, is outraged at this incident that has, reportedly, increased the number of attacks against the U.S. army. He stated the burning was, "hateful, extremely disrespectful and enormously intolerant." Jones reported he has received around 400 death threats since the burning. Hezbollah, a militant Muslim "Party of God," has advertised a 2.4 million dollar bounty on Jones. These threats are not holding him back from future burnings and he, in fact, will denounce the Qur'an outside a mosque in Dearborn, Michigan.

Soul Surfer Review: Beth- has reached the ears of many Cirque du Solei, Quidam around the world. Bethanys By Shelby Berrios any Hamiltons Story
By Jessica Alfaro Staff Writer
This movie is based on an inspiring true story about a skilled surfer named Bethany Hamilton. Bethany had lost her arm by a 14foot tiger shark while surfing in Hawaii. If the bite was just two inches in it would have been fatal. Less then a month after the incident, Bethany was back on her board surfing again. AnnaSophia Robb played, Bethany Hamilton in her new movie Soul Surfer. This movie shows and inspires people to do things they think they cant or never could. Bethany did what everyone said she couldnt. She got back on her board within three weeks of her accident. Bethany doesnt just surf she competes and wins. Bethanys abiding faith in God is what keeps her going. Bethanys inspiring story
family and close friends had even made a website to tell her story in their point of view. I remember walking into the room after I was told Bethany was awake, her first words to me were ask the doctor when I can surf again, says Timothy, Bethanys older brother. Her story is inspiring and its amazing what she can do even with her disability, says Ashley Moss, 11. I have a disability and have grown up with restrictions and its amazing to hear and watch this girl, not born with a disability, still do what she wanted when she had both arms, says Jessica Lucas, 11. I gave my fear, of not being able to surf with one arm to the Lord. just knowing that he loves us and will help us overcome whatever he gives us to deal with brings me strength, says Bethany. Bethany has a great faith in God and keeps looking to Him for power and
Soul Surfers cont. on Page 4

Staff Writer

In San Joses HP pavilion, Cirque Du Solei, a French Canadian circus, was visiting from March 24th to the 27th.
This particular show is about a young girl named Zoe who is bored and tired of her parents ignoring her and being so distant she feels like her life has no meaning. So, she slides into an imaginary place called the World of Qudiam where the characters there help her free her soul. With hardly any spoken word, the story of Zoe finding her way back home plays out. The company Cirque Du Solei is based in Quebec Canada it started in 1984 with only a group of 20 Street performers,
and opened in Montreal in 1996. They have performed on 5 continents with an international cast of 52 acrobats, musicians, singers and characters. The company has 5,000 employees, including more than 1,200 artists from close to 50 different countries. There are ten major acts in the play, all with amazing stunts. The first act is Aerial Contortion in Silk, the second is Banquine. The third act is called Cloud swing, followed by Diabolos. The midpoint of the play is the German Wheel, the next is Hand Balancing, the seventh act of the play is Skipping Ropes. The next

act is Statue- La Vision. The ninth act of the play is Spanish Webs. The closing act of the play is Aerial Hoops. Two acts of the play the actors bring up members from the audience. Cirque Du Solei will have 23 different plays around the world in 2011.
Page 2 been scheduled for her under his command. As Babydoll retreats into her imagination where reality blurs with fantasy, she becomes a dancer at a brothel along with four other patients that have been wrongly imprisoned. Babydoll teams up with Sweet Pea (Abbie Cornish), Rocket (Jenna Malone), Blondie (Vanessa Hudgens), and Amber (Jamie Chung) in order to escape their captors. To escape the girls need to collect five items, and each time Babydoll dances, they are given the chance to get the next item as they are thrown into yet another reality. The plot has many clear holes that are difficult to ignore: the audience never actually gets to see Babydoll s hypnotic dance, and the majority of the characters were removed in a rather rushed, uncreative way. Most criticism that the film has faced is along the lines of the power of women in an abusive environment, and it is easy to see how women with machine guns and short skirts twirling around can be seen as more obSuckerpunch cont. on Page 4

Liberty High School

Snyder Misses the Point with New Film, Sucker Punch
By Emily Taylor Staff Writer

Bon Iver

All of the elements were there: originality, metaphors, a talented cast, a great soundtrack and the crucial statements of self-sacrifice, the ability to create our own stories, abusive authority, reality versus our dreams, and the power of feminism. Somehow, even with so much material, director Zack Snyder failed to deliver any of these concepts very strongly in his new film Sucker Punch. When Babydoll (Emily Browning) gets sent to a mental asylum by her wicked stepfather after her mother s death, she has five days to escape the impending lobotomy that has
Bon Iver is modern theyve By Jillian Bunker only been around a few years, Staff Writer but that album made me go back in time to every I just moment I have knew that what ever felt such I was doing potent emowas extremely tion. honest. It was The name all the things Bon Iver I wanted my emerged as a music to be. result of VerJustin Vernon. nons cabin solThis passionitude; it means ate musician is good winter Justin Vernon of Bon Iver the front man in French. Afof the band Bon ter Vernons winter, the album Iver, which was formed in 2006. was released and proved him Ever since, their music aims to to be a legitimate indie artplease with its traditional singist. In regards to their success, er-songwriter folk sound, abJustin Vernon says: Im really sorbing attention through penhumbled by everything and am sive melodies. Bon Ivers first album,.It was all the For Emma, Forever Ago, was recorded by Vernon in complete things I wanted my isolation. In 2008, he escaped music to be. to a desolate cabin in Wisconsin and made a record that dis- -Justin Vernon on his first album played the sad, lonely, and soulful aura of winter. This album keeping things in perspective. appeals to an eclectic crowd, as The fans appreciate that, and it captures close to every emoas a result, consider Bon Ivers tion one can feel. As faithful Bon Iver cont. on Page 4 listener, Alix Blevins (12) said:

Sonic the Hedgehog continued from Page 1
lesser chance of receiving bigger cartridges, the games were split into two parts. There were also a few spin offs released on the Sega Genesis, which were a hit or a miss depending on the game. There was Sonic Spinball(1993), a Sonic themed pinball game, Dr. Robotnik's Mean Bean Machine,(1993) a mockup of Tetris, and Sonic 3D Blast(1996), a top-down 3D Sonic game, which unfortunately lacked the sense of speed of the original games. These first five years were among the best for Sonic The Hedgehog.
Trials and Tribulations (2006-2009) Throughout that time was when Sonic started to lack the quality Reinventing the Blue Blur of its predecessors. I dont like (1999-2005) how they recycled some key With the release of the ideas from the previous games. Sega Dreamcast came Sonic -Luke Jung (10). Starting in Adventure, released in 1999. 2006 with the 15th anniversary The game introduced a more release of Sonic the Hedgehog complex stofor the Xbox When youre playing the games, it feels like you are in the game 360 and Playryline, better 3D graphics, getting an adrenaline rush from the speed! -Jacqueline Nares (10) station 3, the third person game was gameplay, recycling the top with no changes. Hedgehog, released on the Nin- praised for its next generation down gameplay from 3D Blast, From 2001-2004 came tendo Gamecube, Playstation 2, graphics, but was negatively a combination of free-roam Sonic Advance 1-3 for the and Xbox. It featured the same Sonic cont. on Page 3
gameplay and high-speed levels, and a vast variety of playable characters. The game received praise for those features and was considered the best game for the Dreamcast. An expanded Nintendo Gamecube version, titled Sonic Adventure DX, was released in 2003, featuring never-before-seen content. In 2001, at the peak of the Dreamcasts retirement, Sonic Adventure 2 was released, marking the 10th anniversary of the first Sonic game. It featured the same gameplay mechanics as the first Adventure, and featured Sonic facing off a rival hedgehog, Shadow, for the first time. The game received positive reviews, but was criticized for its camera angles and less challenging boss fights. Like the first game, it was also rereleased a year later on the Gamecube
Game Boy Advance, which brought back the 2D gameplay from the Sega Genesis games. They were praised for its graphics that seemed almost lifelike for a pixilated 2D game, and that the gameplay was as fun as the original. In 2004, Sonic Heroes was released on the Nintendo Gamecube, Playstation 2, and Xbox in 2004, featuring team-based gameplay with four groups of three characters, each with their own traits and powers required to get through certain puzzles of each set of stages. The game received mix reviews, being praised for its team-based gameplay, but received criticism for its dated graphics and camera angles. In 2005, Shadow the Hedgehog, from Sonic Adventure 2 and Sonic Heroes, received his own spin-off game, titled Shadow the

3D gameplay, but with a darker storyline, multiple storyline paths to choose from, good or evil choices, gunplay, and vehicle driving being put into the mix. It received mixed to negative reviews, being criticized for its gunplay mechanics, unintentional character deaths for doing certain attacks, camera angles, as usual, and the dated graphics. It was also the first Sonic game to receive an E10+ rating from the ESRB.

Page 3

Liberty High School strongest asset for this team was how strong they were in the paint, and that stat really showed up against Butler when they outscored them 26-2 in the paint, thanks to Huskie forward Alex Oriakhi. This Huskie team was youthful group with much energy, to the point that coach Jim Calhoun went on to say he feels re-energized when around this team. More than anything this squad showed that they never believed in what the critics posted and having a little fun leads to great success, congratulations to the 2010-11 Connecticut Mens Basketball team on their championship.
(Photo by Streeter Lecka/ Getty Images)
UConn Dominates Butler, Crowned 2011 Champs!
By Blake Paris Staff Writer
The 2011 NCAA Mens college basketball tournament really lived up to the nickname of March Madness and when it was all said and done, the Connecticut Huskies ended up as champions by beating Butler 53-41 in this years national championship. Lead by superstar guard Kemba Walker, the Huskies went through another grueling year of playing in the Big East conference and used that grind period to persevere through this years tournament. The Huskies went 9-9 in conference and ended up as 9 seed in the Big East conference tournament (but went 23-0 in games outside of conference) but that didnt stop them from winning 5 games in 5 days to win the Big East tournament and earn a automatic bid into the national tournament. The Huskies went 14-0 in tournament games this year by winning the Maui Invitational, Big East tournament and now the national championship. The Huskies reviewed for its controls, gameplay, camera angles, bad storyline, long load times, and the blandness of certain characters. It was considered one of the worst games of the last decade. In 2007, Sonic and the Secret Rings was released for the Nintendo Wii. It received mixed to negative reviews overall, with praise for the improvement over the last few games and its storybook style, but the Mario Party-style mini games were bland and seemed like a last minute option. That same year, Sonic faced off with Mario in Mario and Sonic at the Olympic Games, released on the Nintendo Wii and DS, with positive reaction on the Wii version for its fun gameplay, but lacked quality on the Nintendo DS. In 2008, Sonic Unleashed was released on the Xbox 360, PS3, and Wii with negative reviews on the 360 and PS3 ver-

After that incredible run they pulled off to win the Big East tournament, they definitely became one of my favorites to go to the Final Four.

- Quinn Steely, Senior

were dominant force, especially with Kemba Walker said Liberty Senior Quinn Steely. He also quoted, After that incredible run they pulled off to win the Big East tournament, they definitely became one of my favorites to go to the Final Four. The Huskies went on to beat Bucknell, Cincinnati, powerhouse San Diego State, Arizona, then defeated Kentucky in the semifinals, and then, of course, Butler to win it all. The
Sonic the Hedgehog continued from Page 2
sions for its bad level design on half the levels of the game and the Werehog mechanics, but received mixed reviews on the Wi i for its great control scheme, but dated graphics. The same year, Sonic made his debut in Super Smash Bros. Brawl on the Wii as a playable character. Sonic and the Black Knight was released on the Wii in 2009, continuing the storybook style of Secret Rings, receiving highly negative reviews for its graphics, control scheme, and mediocre storyline. Despite mostly negative reaction from a majority of the games during that time of decade, fans were relieved when Sonic Rush hit the DS in 2005 with a sequel released two years later. It was highly praised for it use of the dual screens and the 2D style of the game. Fan will be relieved again for the next few titles later on.
High Speed Future (2010-Present) In 2010, a sequel to Sonic 1-3 was released under Sonic the Hedgehog 4: Episode 1 with great anticipation from the fans and their dreams for a real sequel came true. The game brought back the exact style of the Sega Genesis games, despite the Game Boy Advance and DS taking the same path. It featured the same style of the levels, music, enemies, and boss fights of the original games. The biggest difference was the 3D art style and homing attack from the 3D Sonic games. Sonic Colors was released the same year on the Wii with great reviews for its vastly improved camera and control scheme and its colorful graphics for a Wii game. A teaser video was released for a new game featuring the current generation Sonic racing with a clone of him in his original Genesis design without the pixels. The game doesnt have a title at the moment, but will be released this fall for the Xbox 360 and PS3. I hope they in-
clude a more complex storyline in future games! -Jacqueline Nares-10. We hope for the best for the future of the series. Spin-offs and More (1993-Present) There were many spin-offs for Sonic the Hedgehog. There were a few TV shows and a comic series by Archie. The animated TV shows were the comedic Adventures of Sonic the Hedgehog (1993), the serious toned Sonic Sat AM (1993), the rockoriented Sonic Underground (1993-1996), and the anime Sonic X (2003-present). The comic series turned out to be a success and new issues are still made. The T.V. shows received mixed to negative reaction, with the worst being Adventures of Sonic the Hedgehog. Sonic has been going high speed for 20 years now. With over 40+ games in the series and still counting, 4 TV shows, and a comic series, Sonic the Hedgehog has done it all! The future is bound to be best for the blue hedgehog!

Soul Surfers cont. from Pg. 1

Page 4

this June, when their new album will be released. Simply close strength. When people ask me your eyes and enjoy Bon Ivers what my faith in God means to fresh and distinct sound. me, I usually answer in just one Suckerpunch cont. from Pg. 2 word: everything!.I dont fear sharks, I am in their terri- jectifying then empowering. tory doing what I love. Throughout the layers of realities one might mistake this Bon Iver cont. from Pg. 2 film for Inception, however everything is so plainly spelled music as genuine. More recently, Bon Iver out that it lacks pretty much any recorded with Kanye West for intellectual concepts that one Wests album, My Beautiful might hope to get from a realDark Twisted Fantasy; fans ity bending movie. The movie are torn on this project, as many would have been more enjoysupport this collaboration and able for me if it was just about many oppose it. I, personally, the five girls in the asylum, bewould rather see him work solo cause all the rawness that would on his music; their styles are too be there has been covered up and different and I would hate to see polished by the fantasy worlds. The most prevailing idea him change that, Krista Fisher (11) said. Alas, their partnership was presented at the end of the recently ended and Bon Iver has movie, are we living our own since been working on the fol- life or are we just a supporting low-up to For Emma, Forever character for someone elses? Ago. This album is one of the Sucker Punch dares us to live most anticipated albums of 2011 life for ourselves and to make for several magazines, websites, the story we live, our own. and students. While Bon Iver appears to be successful, many people have yet to discover their music. A perfect chance to do so is
The Lions Roar Staff 2010-2011:
Editors: Corrine Allan & Amanda Mathews
Staff Writers: Jessica Alfaro, Shelby Barrios, Jillian Bunker, Matthew Castle, Thomas Ciprian, Olivia Cox, Hailey Cross, Kenzie Dillon, Tracy Dillon, Tommy Dwyer, Heather Grady, Sarah Graney, David Guerro, Manijeh Khoja, Ashley Kimble, Hailey Kriens, Danielle Larusso, Scott Milne, Michael Najera, Josh Noriega, Blake Paris, Gina Pistochini, Nicholas Pruett, Briana Rael, Mikaela Raimondi, Amber Ralph, Stephen Schnieder, Alex Talbot, Emily Taylor, Sierra Taylor, Omar Valasquez, Toni Vargas, Victoria Wolfe.