Internet:

www.seltron.info

E- mail:

info@seltron.info

Table of contents

User manual Appearance and descripton of AD1...4 Operating mode selection...6 Correcting the day and night temperature..6 Decreasing the night temperature..7 PARTY and ECO operating mode..7 Setting the accurate time...8 Pre-setted time programs...9 Modifying the time program...10 Battery exchange...12 Command to quick save and quit (Escape)..12 Setting manual Menu....13 Factory settings...16 Installation manual Place of mount...17 Mounting the wall plate..17 Connecting the wires...19 Connecting the AD1 to the controllers..20 Technical data...24 Conformity with standards and directives..24 Guarantee....25 Disposal of old electrical & electronic equipment..26
Apearance and descritpion of AD1
AD1 is a powerful, modern designed room unit with room temperature display and weekly program timer. AD1 is used for remote control of heating systems from your living room. AD1 is simple to use and very practical with help of the Party and Eco keys.

LEGEND

Hold key while pressing other keys.
Hold key until you hear a beep sound.

Press and release key.

Press key to increase or decrease value.

4 USER MANUAL

Day and time

Room temperature

Program timer
- night temperatue - day temperature

PARTY ECO Operating mode

Knob for correcting the requested day and night temperature
PARTY day temperature activation
Day temperature mode by program timer
ECO - night temperature activation

Picture 1

USER MANUAL

Operating mode selection

Room unit operates according to the program timer.

Picture 2

Picture 3
Described options are valid only when the room unit AD1 is connected so that it uses his own program timer (picture 25 and 27). In that case the knob for operating mode selection must be in position.
Correcting the day and night temperature

Picture 4

Decreasing the night temperature

Picture 5

For setting the reduction you should pull the AD1 out off the wall plate (picture 14 - OPEN).
PARTY and ECO operating mode
Setting the accurate time
Hours Hold key and press key ( ) or ( ) to set the hours (Picture 6). Picture 6

Picture 7 Day

Picture 8
If the AD1, by battery exchange, isnt functional for a while, is the time set to Monday, 20:00.

Pre-setted time programs

Program selection Hold key and by pressing key select the suitable time program (Picture 9). Select between Pr1, Pr2, Pr3, Pr4 and - - -. The selected time program always overwrites the previous one. To keep the current time program active, select - - -.

Picture 9

Day Time Day Time
Table of pre-setted time programs.

USER MANUAL 9

Modifying the time program
The selected time program can be freely modified. In that way you can make your own time program. Hold key and press key (Picture 10). Release both keys after you hear a beep. The display writes out CH1 (Picture 11).

Picture 10

Picture 11
Press key ( ) or ( ) to select the program place that you want to modify. The display simultaneously writes out the time command and the successive number of the program space (Picture 12).
Successive number of the program space

Time command

Picture 12
Program timer - day temperature - night temperature

Unused time command

Picture 13

Battery exchange

Picture 14 Battery exchange should be done within 20 seconds. In other case you will have to set the accurate time again.
Command to quick save and quit (Escape)
Every time you wish to quick store and quit set-up, hold key press key. Release both keys after you hear a beep. and
All modifications you made, are stored.
Picture 15 Menu navigation
Move to the left Picture 16

SETTING MANUAL

Move to the right Move up or increase

Move down or decrease

Entrance
Group S1 is by default (factory) settings locked. For unlocking the group S1 see chapter Service group S1. Picture 17 Successive Nr. of the line Group name Picture 18 Time program CH1 For changing the time program see chapter Modifying the time program (page 10). Data group d1 This group is sort of AD1 identification. Group d1 only shows data about AD1, meanwhile changing isnt possible. Group d1 contains the following data: - [d1.1] thermostat type (AD1) - [d1.2] software version - [d1.3] calibration of the temperature sensor Parameter

Program group P1 Program group P1 is used for the thermostat user settings. To change the selected parameter, hold key for approximately 5 seconds. Parameter starts to flash. Press key ( ) or ( ) to set the parameter value. To store the setted value, again hold key for approximately 5 seconds. Group P1 contains the following parameters:
- [S1.1] - [S1.2] (0.1 C, 0.2 C, 0.5 C, 1.0 C) Access to parameter S1.1 is possible in the following way. Hold key for 20 seconds (picture 19). Release the key after you hear a beep sound. On the display appears parameter (S1.1). Now it is possible to modify this or any other parameter.

Picture 19

SETTING MANUAL 15

Factory settings

To restore the factory settings hold keys and for approx. 20 seconds (Picture 20). Release keys after you hear a beep. Picture 20 Factory settings are the following: Program group P1 - [P1.1] night temperature (0 C) Service group S1 - [S1.1] group locking (1 - locked S1) - [S1.2] measured temperature round up (0.5 C)

Place of mount

Place of mount is very important for proper ST1 operation. Suitable places are inner walls, which arent sun lighted or exposed to sources of heat and wind. AD1 should be mounted approximately 150 cm above the floor (Picture 21).

Picture 21

Mounting the wall plate
Remove the AD1 from the wall plate, by doing the following. With one hand hold AD1 in height of keys and with other hand the wall plate. Now pull them apart (Picture 22). Picture 22

INSTALLATION MANUAL 17

for the flushbox

for the wall

Picture 23

INSTALL ATION MANUAL

Connecting the wires
WARNING: Mounting and wiring connections must be done by a qualified installer or authorized company. Local regulations or VDE 0100 and EN IEC 60364 regulations for electrical installations must be considered by doing the wiring connections. Bring the wires through the opening in bottom of the wall plate (Picture 23- position A). Room unit AD1 is connected like room sensor with temperature corretcion with 2-wire cable. The connection is more shown detailed on pictures 24-27.

INSTALLATION MANUAL

Connecting AD1 on heating controllers
Connection - the progam timer on the heating controller is used:

- Controller CMP12+ - Controller CMP12+/R

Room unit AD1 Picture 24

20 INSTALL ATION MANUAL
Connection - the program timer on the room unit is used:
-Controller CMP12+ -Controller CMP12+/R

Room unit AD1 Picture 25

INSTALLATION MANUAL 21
-Controller Teramatik D1 -Controller Teramatik D2 -Controller HRD10UB -Controller HRD10UBK -Controller HRD11UB

R= 56 k

Room unit AD1 Picture 26

22 INSTALLATION MANUAL

Room unit AD1 Picture 27

INSTALLATION MANUAL 23

Technical data
Model:.. AD1 Power supply:.. 2 batteries LR03, type AAA Consumption:.. I= 0,022 mA; P= 0,066 mW Temperature sensor:.. Murata NTC (10 kE) Safety class:.. IP 30 by SIST EN 60529 Degree of protection:.. II by SIST EN 60730-1 Housing:... ABS thermoplast, white Dimensions (l w h):. 112 [mm] Weight:.. 150 g
Conformity with standards and directives
Seltron d.o.o. declares, with full responsibility, that unit AD1 meets the requirements and rules for the electrical equipment, designed to use within certain voltage levels (EC directive for low voltage (LVD) 73/23 EEC, 93/68 EEC) and requirements and rules for electro-magnetic compatibility (EMC) (EC directive for electromagnetic compatibility 89/336 EEC, 92/31 EEC, 93/68 EEC). Product description: Room unit AD1 Applied standards: SIST EN 60730-1:1995, SIST EN60730-2-9:1997, SIST EN 50081-1:1995, SIST EN 50082-1:1995, SIST EN 55014-1:2001, SIST EN 55014-2:1997.
24 TECHNICAL DATA, STATEMENTS

Guarantee

This product complies with all the regulations and declared characteristics. We grant 2 years guarantee on the product, commencing on the date of purchase. We will eliminate any defects in the product resulting from faults in materials, workmanship, malfunctions or imperfection. We retain the right to repair or completely replace the product as we may choose. This guarantee does not cover damages as a result of improper use, normal wear and defects that have no effect on value, functionality and operation safety of the product. This guarantee becomes void if repairs are done by unauthorized person or original spare parts are not used. For service within the guarantee period, hand or send the complete product, together with the sales receipt to authorised service or dealer. This guarantee is valid in every country, where the product was supplied by company SELTRON or its authorised dealer.
TECHNICAL DATA, STATEMENTS
SELTRON d.o.o. Ruka cesta Bistrica ob Dravi SI - SLOVENIJA
Tel: +386 (0)Fax: + 386 (0)http://www.seltron.info Email: info@seltron.info

J5060349

V2.0r2

User manual Setting manual Installation manual
Telewarm G1 -switch for remote control with telephone -output 230 V ~, 50 Hz Telewarm G1-D -switch for remote control with telephone -potential-free output
Telewarm G1 and Telewarm G1-D
We are thanking you for your confidence by buying a SELTRON product. We will further try to deepen and strengthen your confidence by improving quality of products, information's and service. If you want to take advantage of all device capabilities, you must carefully read this user manual. Keep this manual at hand for further reference. After you no longer need this device please take care of proper removal.

Table of contents

Preface 4 USER MANUAL Telewarm G1 appearance5 Telewarm G1-D appearance5 Establishing a phone line 6 Entering the identification code6 Activation of controlled device 6 Deactivation of controlled device 7 Activation with limited duration7 Activation with delay7 Disconnecting the phone line7 Light for identification of the Telewarm G44 operation mode7 Manual activation and deactivation of controlled device 7 Tone signalisation 8 Identification code 8 Nr. of dial tones 8 SETTING MANUAL Modifying the identification code and nr. of dial tones9 Reset 9 INSTALLATION MANUAL Telewarm G1 installation10 Telewarm G1-D installation11 Technical data 12 Guarantee12 Disposal of Old Electrical & Electronic Equipment 13

Preface

Telewarm G1 / G1-D is a telephone controlled switch, for remote activation and deactivation of electric devices, with the telephone. Controlled device can be activated or deactivated from any part of the world, as long as we have telephone with tone dialling (DTMF). Telephone can be stationary or mobile. Telewarm can only be used by persons, who know Telewarms phone number and identification code.
Telewarm G1 can be used to control the devices, that meet all the requirements and safety regulations, and are intended for operation without human supervision.
If not stated otherwise, these instructions apply for both Telewarm editions.

USER MANUAL

Telewarm G1 appearance
1 - operation mode indicator 2 - socket for controlled device 3 - key MODE 4 - socket for phone (PHONE) 5 - socket for phone line (LINE)

Telewarm G1-D appearance

1 - operation mode indicator 2 - key MODE 3 - socket for controlled device (REMOTE) 4 - socket for phone line and phone T-connector (LINE)
Establishing a telephone line
Call the phone number, on which the Telewarm is connected. After certain number of dial tones, setted by user (see chapter Changing the nr. of dial tones), Telewarm automatically activates and informs user with three repeated signals. If we call Telewarm from phone central with pulse (decade) dial, the telephone must be changed to tone dial (DTMF), after the line is established. Usually this is done with switch or by pressing the key. In case we dont have telephone with tone dialling, we can use a special device that generates tones (tone generator).
Entering the identification code
After establishing the phone line with Telewarm, we have 30 seconds of time, to enter the identification code. If we dont enter the correct code in this time, Telewarm automatically disconnects the phone line. After entering the correct identification code, we hear a tone signal, that signalises state of Telewarm (see chapter Tone signalisation). If we dont hear a tone signal after entering the identification code, the identification code must be re-entered. If after three dial attempts, the identification code isnt entered correctly, Telewarm automatically disconnects line and goes offline for next 30 minutes.
Activation of controlled device
Telewarm will activate the controlled device, when we press key. Command is executed, if we hear one quickly repeating tone signal (see chapter Tone signalisation).
Deactivation of controlled device
Telewarm will deactivate the controlled device when we press key #. Command is executed, when we hear one slowly repeating tone signal (see chapter Tone signalisation).

Activation with limited duration
Telewarm will activate the controlled device when we enter 0nn and automatically deactivate the controlled device, after setted time of nn minutes expires. Command is executed, when we hear double quickly repeated tone signal (see chapter Tone signalisation).

Activation with delay

Telewarm will start to count the setted time, when we enter 0nn# and automatically activate the device, after setted time of nn minutes expires. Command is activated when we hear double slowly repeated tone signal (see chapter Tone signalisation).
Disconnecting the phone line
When finished working with the Telewarm (status check up, activation or deactivation), disconnect the phone line. You can do that on two ways: - hang up the phone (Telewarm will automatically end the connection in less than 30 seconds), - type in 000 (Telewarm immediately disconnects the phone line).
Light for indication of the Telewarm G44 operation mode
Signal light indicates Telewarm output port state. Light blazes: - device connected to the Telewarm G1 is activated, - Telewarm G1-D output port is in short circuit, Light is off: - device, connected to Telewarm G1 is deactivated, - Telewarm G1-D output port is open (open contacts).
Manual activation and deactivation of the controlled device
Telewarm can be manually activated or deactivated, by holding the button MODE for 3 seconds.

Tone signalisation

For easy use, all the Telewarm functions are signalised with the tone signals. Programming or code entry

Error by entry 1 sec

Output port activation Time limited activation of output port 2 sec Output port deactivation
Delayed output port activation

Identification code

Identification code is 4 digit number from 0000 to 9999 that enables misuse of Telewarm by unauthorized person. Factory pre-setted identification code is 1234 (also when Telewarm is reseted).

Nr. of dial tones

Telewarm is together with the phone parallel connected to the phone line. If Telewarm activates on a first dial tone, the use of phone or fax is impossible. With programming, we set nr. of dial tones, by which the Telewarm will activate and take the phone call. Number of dial tones can be setted between 0 and 9, where 0 means 10 dial tones. Factory pre-set nr. of dial tones (also after reset) is 8.

SETTING MANUAL

Modifying the identification code and nr. of dial tones
Telewarm is programmed with the telephone. For programming the Telewarm is used tone dialing, what in case of calling from public phone, might result as a call to wrong or invalid phone number. If the phone is connected to a public phone central with tone dial, we suggest that you establish a phone line first. We can do that, on the following way. We call a friend and ask him to disconnect the line. Now we can program the Telewarm, without fear of calling invalid or wrong number. If the phone is connected to a public phone central with pulse dial, there is no fear of calling wrong or invalid phone number and no outside connection is needed for programming. - We pick up the phone where we hear the tone for free line. - We establish the phone line and ask the called person to hang up the phone. In phone is now no signal. - We press key MODE 10 times. We hear three short repeated beeps. - We insert new identification code (4 digits) and number of dial tones (from 0 to 9, where 0 means 10 dials) by which the Telewarm will activate ant take the call. Example: 54027 (identification code is 5402; number of dial tones is 7) 29130 (identification code is 2913; number of dial tones is 10) - After the new identification code entry, a slowly repeated tone signal indicates that the Telewarm is deactivated. - Now is possible to test the Telewarms operation or to disconnect the line.
To reset or restore the factory settings, do the following: Press key MODE 10 times and then at least 30 seconds dont press no key. Factory settings are the following: - identification code: 1234 - number of dial tones: 8

INSTALLATION MANUAL

Telewarm G1 installation
Plug the Telewarm G1 in free electric plug and connect the telephone lines (line-in and phone).
Outside phone Telewarm G1 House phone

Telephone network

Controlled electric device

230 V ~

Telewarm G1-D installation
Telewarm G1-D can be connected to a different Sletron controllers, as shown on picture bellow.

Teramatik D1, Teramatik D2 HRD10UB, HRD10UBK HRD11UB - connection to terminals GND and 12 (BF2)
room thermostat ST1 room thermostat ST2 - connection to terminals 1 and 2
room unit DD2 - connection to terminals 3 and 4
Compact CMP12+ Compact CMP12+/R - connection to terminals 7 (GND) and 8 (BF/KF)

Telewarm G1-D

House phone

Outside phone

Connector box T connector

Technical data

Specifications Power supply 230 V ~ , 50 Hz Consumption max. 1 VA Max. load (Telewarm G1)6 A ~, 230 V ~ Max. load (Telewarm G1-D)2 A ~, 230 V ~ Degree of protectionIP 31 by SIST EN 60529 Safety class I by SIST EN 60730-1 Excess voltage protection 20 kV (8/20 s), two-level Housing ABS - thermoplastic Dimensions (w x h x d)65 x 120 x 73 mm Operating environment5 C to +40 C Storage temperature -20 C to +65 C

Guarantee

This product complies with all the regulations and declared characteristics. We grant 2 years guarantee on the product, commencing on the date of purchase. We will eliminate any defects in the product resulting from faults in materials, workmanship, malfunctions or imperfection. We retain the right to repair or completely replace the product as we may choose. This guarantee does not cover damages as a result of improper use, normal wear and defects that have no effect on value, functionality and operation safety of the product. This guarantee becomes void if repairs are done by unauthorized person or original spare parts are not used. For service within the guarantee period, hand or send the complete product, together with the sales receipt to authorised service or dealer. This guarantee is valid in every country, where the product was supplied by company SELTRON or its authorised dealer.

TECHNICAL DATA

Disposal of Old Electrical & Electronic Equipment
Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems)
This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.
SELTRON d.o.o. Ruka cesta Bistrica ob Dravi Slovenija tel: +386 (0)fax: +386 (0)http://www.seltron.si Email:info@seltron.si

We retain the right for modifications.

J5060311