AL-1642CS_Manual.book

AL-1642CS
DIGITAL LASER COPIER DIGITAL MULTIFUNCTIONAL SYSTEM OPERATION MANUAL
INTRODUCTION SETTING UP THE UNIT LOADING PAPER INSTALLING THE SOFTWARE MAKING COPIES SPECIAL FUNCTIONS MAINTENANCE TROUBLESHOOTING THE UNIT APPENDIX

ED IN CHINA

005D KS1 INSE1477QSZZ

FOR YOUR PROTECTION.

To aid in reporting this unit in case of loss or theft, please record below the model number and serial number located on the back of the unit. We also suggest you record all the information listed and retain for future reference. MODEL NUMBER DATE OF PURCHASE Dealer Address State Service Station Address State Zip City Telephone Zip City Telephone SERIAL NUMBER
To obtain service, or to obtain product literature, accessories, or supplies, please call or 1-(630)378-3590 in the USA 905-568-7140 in Canada.
For customer assistance, please visit http://www.sharpusa.com/ (for USA) or http://www.sharp.ca/ (for Canada) on the World Wide Web or call 1-(630)378-3590 (for USA).
Do not make copies of anything which is prohibited from copying by law. The following items are normally prohibited from copying by national law. Other items may be prohibited by local law. Money Stamps Bonds Stocks Bank drafts Checks Passports Driver's licenses

CAUTIONS

Caution label on the unit
The label ( , ) in the fusing area of the unit indicates the following: : Caution, risk of danger : Caution, hot surface

Cautions on using

Follow the cautions below when using this unit.

Warning:

The fusing area is hot. Exercise care in this area when removing misfed paper. Do not look directly at the light source. Doing so may damage your eyes.

Caution:

Place the unit on a firm, level surface. Do not install the unit in a humid or dusty location. When the unit is not used for a long time, for example for consecutive holidays, turn the power switch off and remove the power cord from the outlet. When moving the unit, be sure to turn the power switch off and remove the power cord from the outlet. Do not switch the unit rapidly on and off. After turning the unit off, wait 10 to 15 seconds before turning it back on. Do not cover the unit with a dust cover, cloth or plastic film while the power is on. Doing so may prevent heat radiation, damaging the unit. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. The socket-outlet shall be installed near the unit and shall be easily accessible.
Important points when selecting an installation site
Do not install your unit in areas that are: damp, humid, or very dusty exposed to direct sunlight poorly ventilated subject to extreme temperature or humidity changes, e.g., near an air conditioner or heater. Be sure to allow the required space around the 8" (20 cm) machine for servicing and proper ventilation.

4" (10 cm)

Cautions on handling
Be careful in handling the unit as follows to maintain the performance of this unit. Do not drop the unit, subject it to shock or strike it against any object. Do not expose the drum cartridge to direct sunlight. Doing so will damage the surface (green portion) of the drum cartridge, causing smudges on copies. Store spare supplies such as drum cartridges and TD cartridges in a dark place without removing from the package before use. If they are exposed to direct sunlight, smudges on copies may result. Do not touch the surface (green portion) of the drum cartridge. Doing so will damage the surface of the cartridge, causing smudges on copies.

Supply and Consumables

The supply of spare parts for a repair of the appliance is guaranteed for at least 7 years following the termination of production. Spare parts are those parts of the apparatus which may break down within the scope of the ordinary use of the product - whereas those parts which normally exceed the life of the product are not to be considered as spare parts. Consumables too, are available for 7 years following the termination of production.
Trademark acknowledgements
Sharpdesk is a trademark of Sharp Corporation. Microsoft, Windows, Windows 95, Windows 98, Windows Me, Windows NT 4.0, Windows 2000, Windows XP and Internet Explorer are registered trademarks or trademarks of Microsoft Corporation in the U.S.A. and other countries. IBM, PC/AT, and PowerPC are trademarks of International Business Machines Corporation. Acrobat Reader Copyright 1987-2002 Adobe Systems Incorporated. All rights reserved. Adobe, the Adobe logo, Acrobat, and the Acrobat logo are trademarks of Adobe Systems Incorporated. All other trademarks and copyrights are the property of their respective owners.

For users in the USA

As an ENERGY STAR Partner, SHARP has determined that this product meets the ENERGY STAR guidelines for energy efficiency.

How to use the online manual
Explains how to use the online manual.
Provides information on how to print a document.
Explains how to scan using the scanner driver and how to adjust the settings for the Button Manager.

Troubleshooting

Provides instructions on how to solve driver or software problems.
Conventions used in this manual and online manual
Illustrations of driver screens and other computer screens show the screens that appear in Windows XP Home Edition. Some of the names that appear in these illustrations may differ slightly from the screens that appear in other operating systems. This operation manual refers to the Single Pass Feeder as the "SPF". In this manual, the following icons are used to provide the user with information pertinent to the use of the unit. Warns the user that injury may result if the contents of the warning are not properly followed. Cautions the user that damage to the unit or one of its components may result if the contents of the caution are not properly followed. Notes provide information relevant to the unit regarding specifications, functions, performance, operation and such, that may be useful to the user. Indicates a letter displayed in the display.

PART NAMES

SPF Original guide Document feeder cover Exit area Document feeder tray Interface USB connector Parallel connector

TD cartridge

Drum cartridge
Document glass Operation panel Front cover Paper tray 1 Paper tray 2 Multi-bypass tray Side cover Side cover open button Bypass tray paper guides
Paper output tray Paper output tray extension Power switch Handle Power cord Fusing unit release lever Transfer charger Charger cleaner

OPERATION PANEL

Original to copy key and indicators Two-sided copies from one-sided originals. Turn on Long Edge or Turn on Short Edge can be selected. Exposure mode selector key and indicators Use to sequentially select the exposure modes: AUTO, MANUAL or PHOTO. Selected mode is shown by a lit indicator. (p.49) Light and dark keys and indicators Use to adjust the MANUAL or PHOTO exposure level. Selected exposure level is shown by a lit indicator. (p.49) Use to start and terminate user program setting. (p.55) Alarm indicators Drum replacement required indicator (p.58) Misfeed indicator (p.63) TD cartridge replacement required indicator (p.57) SPF indicator (p.48) SPF misfeed indicator (p.67) Copy ratio selector key and indicators Use to sequentially select preset reduction/enlargement copy ratios. Selected copy ratio is shown by a lit indicator. (p.51) Copy ratio display (%) key (p.51) Display Displays the specified copy quantity, zoom copy ratio, user program code, and error code. SCANNER key and indicator (p.31, p.39)

The following term is used in this section.
Means the unit as a printer and scanner. For this description, it is assumed that the mouse is configured for right hand operation. To print or scan, the MFP must be in the online state. The scanner feature only works when using a USB interface cable. If any error message appears, solve the problem following the instructions on the screen. After your problem is solved, the installing procedure will be continued. Depending on your problem, you may have to exit the installer. In this case, click the "Cancel" button to exit the installer. After solving your problem, reinstall the software from the beginning.
Installing onto Windows XP (USB/parallel interface)
Before starting the installation, make sure the USB or parallel interface cable is not connected to the MFP.
Insert the supplied CD-ROM into your CD-ROM drive. Click the "start" button, click "My Computer" ( double-click the CD-ROM ( ) icon. ), and then
When any of "Found New Hardware Wizard" messages appear during the software installation, be sure to click the "Cancel" button.
Double-click the "setup" (

) icon.

If the language selection screen appears after you double click the "setup" icon, select the language you wish to use and click the "Next" button. (Normally, the correct language is selected automatically.)
Select the software packages to be installed, and then click the "Next" button.
The software packages with checkmark ( ) on the list on the screen will be installed. Click the "Display README" button to show the information on the selected package.
If you are using the parallel interface connection, do not select the Button Manager checkbox because this feature is not supported with the parallel interface. If the following screen appears, click the "OK" button. Review the contents in "BEFORE INSTALLATION" (p.20), and then select only the appropriate software packages to be installed.
Review the software packages to be installed on the screen, and then click the "Start" button.
The software packages to be installed will be displayed on the screen. If inappropriate packages are displayed, click the "Back" button to select appropriate packages again.
Copying files for MFP driver installation (This step will start if it was selected in step 4).

When the "The MFP driver installation is complete." dialog box appears, click the "OK" button. The Button Manager installer will start.
After confirming the message in the "Welcome" window, click the "Next" button. Read the message in the "Please read the following information." window, and then click the "Next" button. When a message appears that lets you specify the location for the software to be installed, click the "Next" button. If the program displays "Do you want the Button Manager added to Windows Startup?", check "Yes" and click the "OK" button. The setup program will start to copy the files. Click the "Finish" button when the message to inform you of the completion of the installation appears. The Sharpdesk installer will start.
After confirming the message in the "Welcome to Sharpdesk installation" window, click the "Next" button. Read the message in the "Information" window, and then click the "Next" button. When the "Choose Destination Location" window appears, click the "Next" button. When the "Select Program Folder" window appears, click the "Next" button. The setup program will start to copy the files. If the dialog box asking "If you have TIF files saved using Photoshop or Imaging for Windows you should hit Skip" appears, answer the question to continue the Sharpdesk installation. Click the "Finish" button when the message to inform you of the completion of the installation appears.
Click the "Close" button when the message to inform you of the completion of the installation appears. When the "Now connect the MFP interface cable to the PC." dialog box or "After Windows system restarts." dialog box appears, click the "OK" button.
Make sure that the power of the MFP is turned on, and then connect the USB interface cable. (p.45)
Windows will detect the MFP and the Plug and Play screen will appear.
Follow the instructions in the Plug and Play screen that appears in your version of Windows to begin the installation.
You have completed the installation of the software.
Installing onto Windows 95/98/Me/NT4.0/2000 (Parallel interface)
The software packages with checkmark ( ) on the list on the screen will be installed. Click the "Display README" button to show the information on the selected package. In Windows 95/NT 4.0, "Button Manager" does not appear. In Windows 98/Me/2000, do not select the "Button Manager" checkbox. because this is not supported when using the parallel interface.

The next screen appears. Make sure that the parallel interface cable is not connected, and click "OK".
Windows 95/NT 4.0 Windows 98/Me/2000
Check the contents of the package on the screen, and then click the "Start" button.
The software packages to be installed will be displayed on the screen. If inappropriate packages are displayed, click the "Back" button to select only appropriate software packages.
Copying files for MFP driver installation and parallel interface setup (This step will start if it was selected in step 4).
After confirming the message in the "Welcome" window, click the "Next" button. A dialog box appears asking you to verify that the USB or parallel interface cable is not connected to the MFP. Make sure that the interface cable is not connected and click the "Next" button. Click the "Next" button in the dialog box to install the MFP driver or Cancel to quit the installation. The setup program will start to copy the files. In Windows 2000, if the following screen appears while the files are being copied (the message may appear more than once), click "Yes" in Windows 2000. The following screen appears. Click the "Yes" button, and then the Model screen will appear. Select the model number that is the same as the model name of your MFP and click the "Next" button. Be sure to select the displayed model number that is the same as the MFP's model name. If they are not the same, the driver will not be installed correctly.
Establish the printer settings and click the "Next" button. Select "LPT1" for the port to be used. If "LPT1" does not appear, it is likely that another printer or peripheral device is using "LPT1". Check your other printers and peripheral devices, and change the port setting as needed so no device is using "LPT1". If you wish the MFP to be your default printer, select "Yes". If not, select "No". When the "Setup has completed gathering all necessary installation information" dialog box appears, click the "Yes" button. The parallel interface driver is installed. When the "The MFP driver installation is complete." dialog box appears, click the "OK" button. The Sharpdesk installer will start.

To use the SHARP Personal MFP series again, perform the same procedure but select the port to be used (for example, LPT1) in step 4.
CONNECTING THE INTERFACE CABLE
This unit includes both USB and parallel interface connectors. Interface cables for connecting the unit to your computer are not included with this unit. Please purchase the appropriate cable for your computer. If you intend to use the unit as a scanner, it must be connected to your computer with a USB interface cable. The scanner function cannot be used if the unit is connected with a parallel cable. USB is available with a PC/AT compatible computer that was originally equipped with USB and had Windows 98, Windows Me, Windows 2000 Professional, Windows XP Professional or Windows XP Home Edition preinstalled. Do not connect the interface cable before installing the MFP driver. The interface cable should be connected during installation of the MFP driver. (p.21)
Connecting the USB interface cable
Obtain a shielded USB interface cable. Insert the cable into the USB interface connector located on the rear of the unit.
Insert the other end of the cable into the interface connector of your computer, or the USB hub connected to your computer.
Connecting the parallel interface cable
Obtain an IEEE1284 shielded parallel interface cable. Ensure that your computer and unit are turned off. Insert the cable into the parallel interface connector located on the rear of the unit, and fasten with clasps.
Insert the other end of the cable into the interface connector of your computer.

COPY FLOW

MAKING COPIES
This chapter explains basic and other copying functions. The unit is equipped with a one-page memory buffer. This memory allows the unit to scan an original once only and make up to 99 copies. This feature improves workflow, reduces operation noise from the copier, and provides higher reliability by reducing wear and tear on the scanning mechanism.
1 Make sure that paper has been loaded in the paper tray 1, paper tray 2 (p.15) or multi-bypass tray (p.17), and check the paper size (p.14).

Press the exposure mode selector key. The PHOTO ( ) indicator will stop blinking and light up steadily. The light and dark indicator marked "3" will light up. The toner save mode is now active.
To return to the standard mode, repeat the procedure but use the dark ( ) key to select exposure level "5" in step 3.

USER PROGRAMS

The user programs allow the parameters of certain functions to be set, changed, or canceled as desired.
Setting the power save modes, auto clear time, stream feeding mode and resolution of AUTO & MANUAL mode
Press and hold down the light ( ) and dark ( ) keys simultaneously for more than 5 seconds until all the alarm indicators ( , , ) blink and " " appears in the display. Use the left copy quantity ( ) key to select a user program number (1: auto clear time, 2: preheat mode, 3: auto power shut-off timer, 4: stream feeding mode, 5: auto power shut-off mode 6: resolution of AUTO & MANUAL mode). The selected number will blink in the left side of the display. Press the start ( ) key. The entered program number will be steadily lit and the currently selected parameter number for the program will blink on the right side of the display. Select the desired parameter using the right copy quantity ( ) key. The entered parameter number will blink on the right of the display.

Program No. 5 6

Mode Auto clear time Preheat mode Auto power shut- off timer Stream feeding mode Auto power shut- off mode Resolution of AUTO & MANUAL mode 0 *3 *0 *0
Parameters OFF, 1 10sec., 2 30sec., 60sec., 4 90sec., 5 120sec. 30sec., 1 2min., *1 30min., 4 OFF, *1 OFF, *1 300dpi, 1 60sec., 2 90sec.
5min., 2 15min., 60 min., 5 120min. ON ON 600dpi
* Factory default settings are indicated with an asterisk (*).
Press the start ( ) key. The right-hand number in the display will be steadily lit and the entered value will be stored.
To change the setting or to set another mode, press the clear ( ) key. The unit will return to step 2.
Press the light ( copy mode.

) or dark (

) key to return to the normal
DISPLAYING TOTAL NUMBER OF COPIES
Use the following procedure to display the total number of copies.
Press and hold down the clear ( ) key for approximately 5 seconds. The total number of copies will appear in two steps, each with three digits. Example: Total number of copies is 1,234.

MAINTENANCE

This chapter describes how to replace the TD cartridge and drum cartridge and how to clean the unit. Be sure to use only genuine SHARP parts and supplies.

Drum cartridge handle

Remove the new drum cartridge from the protective bag and remove the protective cover from the cartridge. Then gently install the new drum cartridge.
Do not touch the surface of the drum (green portion) of the cartridge. Doing so may cause smudges on the copies.
Gently install the TD cartridge. To install the TD cartridge, see step 5 in "INSTALLING THE TD CARTRIDGE" (p.11). Close the front cover and then the side cover by pressing the round projections near the side cover open button. The drum replacement required ( ) indicator will go out and the start ( ) indicator will light up.

CLEANING THE UNIT

Proper care is essential in order to get clean, sharp copies. Be sure to take a few minutes to regularly clean the unit. Do not spray flammable cleaner gas. Gas from the spray may come in contact with the internal electrical components or high-temperature parts of the fusing unit, creating a risk of fire or electrical shock. Before cleaning, be sure to turn the power switch off and remove the power cord from the outlet. Do not use thinner, benzene or other volatile cleaning agents. Doing so may cause deformation, discoloration, deterioration or malfunction.

Cabinet

Wipe the cabinet with a soft, clean cloth.
Document glass and the back side of the SPF
Stains on the document glass, SPF scanning window or SPF roller will also be copied. Wipe the document glass, SPF scanning window and SPF roller with a soft, clean cloth. If necessary, dampen the cloth with a glass cleaner.
Document glass/SPF scanning window

SPF roller

SPF scanning window

Transfer charger

If copies start becoming streaky or blotchy, the transfer charger may be dirty. Clean the charger using the following procedure.
Turn the power switch off. (p.13) Ensure that the multi-bypass tray is open and then open the side cover while pressing the side cover open button. Take the charger cleaner out by holding the tab. Set the charger cleaner onto the right end of the transfer charger, gently slide the cleaner to the left end, and then remove it. Repeat this operation two or three times.

3. Termination.

This license is effective until terminated. You may terminate this License at any time by destroying the Software and related documentation and all copies thereof. This License will terminate immediately without notice from SHARP and/or SHARPS Licensors if you fail to comply with any provision of this License. Upon termination you must destroy the Software and related documentation and all copies thereof.
4. Export Law Assurances.
You agree and certify that neither the Software nor any other technical data received from SHARP, nor the direct product thereof, will be exported outside the United States except as authorized and as permitted by the laws and regulations of the United States. If the Software has been rightfully obtained by you outside of the United States, you agree that you will not re-export the Software nor any other technical data received from SHARP, nor the direct product thereof, except as permitted by the laws and regulations of the United States and the laws and the regulation of the jurisdiction in which you obtained the Software.

5. Government End Users.

If you are acquiring the Software on behalf of any unit or agency of the United States Government, the following provisions apply. The Government agrees: (i) if the Software is supplied to the Department of Defense (DoD), the Software is classified as "Commercial Computer Software" and the Government is acquiring only "restricted rights" in the Software and its documentation as that term is defined in Clause 252.227-7013 (c)(1) of the DFARS; and (ii) if the Software is supplied to any unit or agency of the United States Government other than DoD, the Government's rights in the Software and its documentation will be as defined in Clause 52.22719 (c)(2) of the FAR or, in the case of NASA, in Clause 18-52.227-86 (d) of the NASA Supplement to the FAR.
6. Limited Warranty on Media.
SHARP warrants the disks on which the Software is recorded to be free from defects in materials and workmanship under normal use for a period of ninety (90) days from the date of purchase as evidenced by a copy of the receipt. The entire liability of SHARP and/or its Licensors and your exclusive remedy will be replacement of the disk which fails to meet the limited warranty provided by this Clause 6. A disk will be replaced when it is returned to SHARP or a SHARP authorized representative with a copy of the receipt. SHARP will have no responsibility to replace a disk damaged by accident, abuse or misapplication. ANY IMPLIED WARRANTIES ON THE DISKS, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO NINETY (90) DAYS FROM THE DATE OF DELIVERY. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM JURISDICTION TO JURISDICTION.

2.COMPOSITION / INFORMATION ON INGREDIENTS
Substance[ ] Ingredient Styrene-Acrylate copolymer StyreneHomopolymer Carbon black Iron oxide Polypropylene Parafrfine Metal Complex dye* Preparation[X] CAS No. 29497-14-1 9003-53-6 1333-86-4 1317-61-9 9010-79-1 8002-74-2 109125-51-1 84179-66-8 Proportion 35-45% 35-45% 5-10% 5-10% 1-5% 1-5% < 1% OSHA PEL Not listed Not listed 3.5mg/m Not listed Not listed Not listed 3 0.5mg/m
ACGIH TLV Not listed Not listed 3.5mg/m Not listed Not listed Not listed 3 0.5mg/m
MAK-TWA Not listed Not listed Not listed Not listed Not listed Not listed Not listed
NOHSC-TWA Not listed Not listed 3mg/m Not listed Not listed Not listed Not listed
* EC N0. : 400-110-2, Symbol letter : F, R Phrase : R11
Page : 2/4 Date Revised : Jul. 31, 2002 Date Issued : Jun. 1, 1998 MSDS No. F-00831

3.HAZARDS IDENTIFICATION

Most Important Hazards and Effects of the Products Human Health Effects : There are no anticipated carcinogenic effects from exposure based on animal tests performed using toner. When used as intended according to instructions, studies do not indicate any symptoms of fibrosis will occur. Environmental Effects : No data are available. Specific Hazards : Dust explosion (like most finely divided organic powders) Directive 1999/45/EC(Europe) : Not classified as dangerous

4.FIRST-AID MEASURES

Route(s) of Entry : Inhalation? Yes Skin? No Ingestion? Possible but very unusual.
Inhalation : Remove to fresh air. If symptoms occur, consult medical personnel. Skin Contact : Wash with soap and water for 15 minutes or until particle is removed. If irritation does occur, consult medical personnel. Eye Contact : Flush eyes immediately with water for 15 minutes. If irritation does occur, consult medical personnel. Ingestion : Rinse with water and drink several glasses of water. If irritation or discomfort does occur, consult medical personnel.

5.FIRE-FIGHTING MEASURES

Extinguishing Media : Water, CO2, foam and dry chemicals Special Fire Fighting Procedures : None Fire and Explosion Hazards : Toner material, like most finely divided organic powders, may form an explosive mixture.
6.ACCIDENTAL RELEASE MEASURES
Personal Precautions Environmental Precautions Methods for Cleaning Up : None : None : Wipe off with paper or cloth. Do not use vacuum cleaner when a large amount is released. It, like most finely divided organic powders, is capable of creating a dust explosion.

7.HANDLING AND STORAGE

Handling Technical Measures : None Precautions : None Safe Handling Advice : Use of a dust mask is recommended when handling a large quantity of toner or during long term exposure, as with any non-toxic dust. Try not to disperse the particles. Storage Technical Measures : None Storage Conditions : Keep container closed and Store in a cool and dry place. Keep out of the reach of children. Incompatible Products : None

NFPA Rating (USA) : Health=1 Flammability=1 Reactivity=0 WHMIS Legislation (Canada) : This product is not a controlled product. References IARC(1996) : IARC monographs on the Evaluation of the Carcinogenic Risk of Chemicals to Humans, Vol. 65, Printing Process And Printing Inks, Carbon Black and Some Nitro Compounds, Lyon, pp.149-261 H.Muhle, B.Bellmann, O.Creutzenberg, C.Dasenbrock, H.Ernst, R.Kilpper, J.C.MacKenzie, P.Morrow, U.Mohr, S.Takenaka, and R.Mermelstein(1991) Pulmonary Response to Toner upon Chronic Inhalation Exposure in Rats. Fundamental and Applied Toxicology 17, pp.280-299. The information on this data sheet represents our current data and best opinion as to the proper use in handling of this product under normal conditions. However, all materials may present unknown hazards and should be used with caution. Although certain hazards are described herein, we do not guarantee that these are the only hazards which exist.
Page : 1/4 Date Revised : Apr. 1. 2005 Date Issued : Sep. 1. 2003 MSDS No. F-01231
Product Name : AL-1651CS / AL-1661CS / AL-1631 / AL-1641CS / AL-1642CS /AL-1217D / AL-1457D /FO-DC550 / FO-55ND/AL-1655CS (Black Toner) Supplier Identification : Sharp Corporation 22-22 Nagaike-cho, Abeno-ku, Osaka, Japan Local suppliers are listed below. Please contact the nearest supplier for additional information. Area (Country) (Name and Telephone Number) U.S.A. Sharp Electronics Corporation Sharp Plaza, Mahwah, NJ Telephone number for information : 1-800-237-4277 North Emergency telephone number : 1-800-255-3924 America Canada Sharp Electronics of Canada Ltd. Telephone number for information : 905-890-2100 Emergency telephone number : 1-800-255-3924 Australia Sharp Corporation of Australia PTY. Ltd. Oceania No1 Huntingwood Drive Huntingwood Blacktown N.S.W. Telephone number for information : 1300-13-50-22 Germany Sharp Electronics (Europe) GMBH Sonninstrasse 3, 20097 Hamburg Telephone number to access MSDS : 040-2376-2185 For more information : 040-2376-2613 United Sharp Electronics (U. K.) Ltd. Telephone number for information : 08705-274-277 Kingdom France Sharp Electronics France S.A. Telephone number for information : 01-49-90-34-00 Austria Sharp Electronics GMBH Telephone number for information : 01-727-19-0 Europe Italy Sharp Electronics (Italy) S.P.A. Telephone number for information : 02895951 Spain Sharp Electronics (Espana) S.A. Telephone number for information : 93-581-97-00 Netherlands Sharp Electronics Benelux B.V. Telephone number for information : 30-6359500 Sweden Sharp Electronics Nordic AB Telephone number for information : 08-634-36-00 Switzerland Sharp Electronics(Schweiz)AG Telephone number for information : 01-846-6111 U.A.E. Sharp Middle East FZE Middle P.O.Box 17115 Jebel Ali, Dubai East Telephone number for information : 04-815311

mmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmm
mmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmm
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

WARNING:

FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the users authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: G Reorient or relocate the receiving antenna. G Increase the separation between the equipment and receiver. G Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. G Consult the dealer or an experienced radio/TV technician for help.
Notice for Users in U.S.A. Installed Printer Board (For Printer Standard Model) Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Model Number: AL- 12PK (Printer/Scanner Expansion Kit) Responsible Party: SHARP ELECTRONICS CORPORATION Sharp Plaza, Mahwah, New Jersey 07430-1163 TEL: 1-800-BE-SHARP