AR-156

DIGITAL LASER COPIER OPERATION MANUAL
GETTING STARTED MAKING COPIES SPECIAL FUNCTIONS SUPPLIES AND USER MAINTENANCE COPIER TROUBLE? APPENDIX OPTIONAL EQUIPMENT

FOR YOUR RECORDS.

To protect against loss or theft, record and retain for reference the copiers serial number located on the back of the unit.
Model Number Serial Number Date of Purchase Place of Purchase Authorized Sharp Copier Service Department Number

CONTENTS

1 GETTING STARTED
INTRODUCTION 3 CAUTIONS 4 MAIN FEATURES 5 PART NAMES 6 OPERATION PANEL 7 COPIER INSTALLATION 8 CAUTIONS ON HANDLING 9 LOADING COPY PAPER 10

MAKING COPIES

NORMAL COPYING 12 Stream feeding mode 16 EXPOSURE ADJUSTMENT/PHOTO COPYING REDUCTION/ENLARGEMENT/ZOOM 17 BYPASS FEED (including special paper) 18

SPECIAL FUNCTIONS

DESCRIPTION OF SPECIAL FUNCTIONS 20 TONER SAVE MODE 20 USER PROGRAMS (power save modes, auto clear time, stream feeding mode) 21 Setting the power save modes, auto clear time, and stream feeding mode 21 DISPLAYING TOTAL NUMBER OF COPIES 22
SUPPLIES AND USER MAINTENANCE
TONER CARTRIDGE REPLACEMENT Toner cartridge life Cabinet USER MAINTENANCE 23
Original table and original cover Transfer charger When copier is not in use

COPIER TROUBLE?

MISFEED REMOVAL A Misfeed in the paper feed area B Misfeed in the fusing area D Misfeed in the RSPF DEVELOPER REQUIRED MAINTENANCE REQUIRED TROUBLESHOOTING STATUS INDICATORS C Misfeed in the transport area
AUTOMATIC EXPOSURE ADJUSTMENT

APPENDIX

SPECIFICATIONS SUPPLIES 36
Types and sizes of copy paper

OPTIONAL EQUIPMENT

SYSTEM CONFIGURATION Part names 250-SHEET PAPER FEED UNIT (AR-DE9) Loading copy paper Misfeed removal Specifications

GETTING STARTED

This chapter provides basic information for using the copier.

INTRODUCTION

This copier has been designed to provide intuitive operating ease while requiring a minimum amount of space. To get full use of all copier features, be sure to familiarize yourself with this manual and the copier. For quick reference during copier use, keep this manual in a handy location. This copier can also be used as a laser printer if an optional printer expansion kit is installed. This manual describes only the copier features. For description of the printer features, see their separate manual.

Getting started

Conventions used in this manual In this manual, the following icons are used to provide the user with information pertinent to the use of the copier. Warns the user that injury to the user or damage to the copier may result if the contents of the warning are not properly followed. Cautions the user that damage to the copier or one of its components may result if the contents of the caution are not properly followed. Notes provide information relevant to the copier regarding specifications, functions, performance, operation and such, that may be useful to the user. Indicates a letter displayed in the display.

CAUTIONS

Follow the cautions below when using this copier.
The fusing area is hot. Exercise care in this area when removing misfed paper. Do not look directly at the light source. Doing so may damage your eyes. G Do not switch the copier rapidly on and off. After turning the copier off, wait 10 to 15 seconds before turning it back on. G Copier power must be turned off before installing any supplies.
.G Place the copier on a firm, level surface.
Do not install the copier in a humid or dusty location. When the copier is not used for a long time, for example, for consecutive holidays, turn the power switch off and remove the power cord from the outlet. When moving the copier, be sure to turn the power switch off and remove the power cord from the outlet. Do not cover the copier with a dust cover, cloth or plastic film while the power is on. Doing so may prevent heat radiation, damaging the copier. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

SAFETY PRECAUTIONS

This Digital Copier is rated Class 1 and complies with 21 CFR 1040.10 and 1040.11 of the CDRH standards. This means that the copier does not produce hazardous laser radiation. For your safety, observe the precautions below. G Do not remove the cabinet, operation panel or any other covers. G The copiers exterior covers contain several safety interlock switches. Do not bypass any safety interlock by inserting wedges or other items into switch slots.

MAIN FEATURES

High-speed laser copying
Since warm-up time is zero, copying can be started immediately after the power switch is turned on. First-copy time is only 9.6 seconds (normal mode). Copying speed is 15 copies/min., which adapts to business use, allowing improvement of working efficiency.
High-quality digital image
High-quality image copying at 600 dpi can be performed. In addition to the automatic exposure mode, the manual exposure can be adjusted in five steps. The photo mode copying function allows clear copying of delicate halftone original images such as monochrome photos and color photos.
Substantial copying functions
Zoom copying from 50% to 200% in 1% increments can be performed. Continuous copying of maximum 99 sheets can also be performed. Automatic document feeding through the reversing single pass feeder (RSPF) can be performed. Toner save mode reduces toner consumption by approximately 10%. User programs allow setting/modification of functions for customers needs. Automatic two-sided copying can be performed.

Scan once/ Print many

This copier is equipped with a 1-page memory buffer. This Memory allows the copier to scan an original once only and make up to 99 copies. This feature allows for improved workflow, reduced operating noise from the copier and reduced wear and tear on the scanning mechanism. This feature provides for a higher reliability.

Printer feature

This copier can be used as a laser printer by installing an optional printer expansion kit.
Environmentally friendly design
Paper output tray is housed in the copier for space saving. Preheat and auto power shut-off modes are provided to reduce power consumption in standby mode.

PART NAMES

Original table

RSPF exit area

Original guides Document feeder tray

Operation panel

Original cover

Feeding roller cover

Side cover Bypass tray Bypass tray guides

Paper tray Handle

Front cover

Side cover open button

Cover for optional printer interface * A printer expansion kit is optional.
Paper output tray Paper output tray extension Power cord socket Toner cartridge lock release lever Power switch Handle

Toner cartridge

Transfer charger
Fusing unit Charger cleaner release lever

Photoconductive drum

OPERATION PANEL
Original to copy key and indicators : Two-sided copies from onesided originals. Turn on Long Edge or Turn on Short Edge can be selected. : Two-sided copies from twosided originals. (Can be selected only when the RSPF is used.) : One-sided copies from twosided originals. (Can be selected only when the RSPF is used.) Exposure mode selector key and indicators Use to sequentially select the exposure modes: AUTO, MANUAL or PHOTO. Selected mode is shown by a lit indicator. (p. 16) Light and dark keys and exposure indicators Use to adjust the MANUAL or PHOTO exposure level. Selected exposure level is shown by a lit indicator. (p.16) Use to start and terminate user program setting. (p. 21) Alarm indicators : Developer replacement required indicator (p. 32) : Misfeed indicator (p. 27) : Toner cartridge replacement required indicator (p. 23) : Maintenance indicator (p. 32) RSPF indicator (p. 13) RSPF misfeed indicator (p. 30) Copy ratio selector key and copy ratio indicators Use to sequentially select preset reduction/ enlargement copy ratios. Selected copy ratio is shown by a lit indicator. (p. 17) Zoom indicator (p. 17) Copy ratio display (%) key (p. 17) Display Displays the specified copy quantity, zoom copy ratio, user program code, and error code.
ON LINE indicator Lights up when the machine is used as a printer. To use the copier as a printer, an optional printer expansion kit is needed. ON LINE key Changes between the on-line and off-line modes when the PCL expansion kit has been installed and a PCL printer is used. Changes modes from the off-line to on-line when the GDI expansion kit has been installed and a GDI printer is used. DATA indicator Indicates that the printer is receiving or processing print data. To use the copier as a printer, an optional PCL expansion kit is needed. Power save indicator Lights up when the copier is in a power save mode. (p. 20, 21) Tray select key Use to select a paper feed station (paper tray or bypass tray). (p. 19) Paper feed location indicators Light up to show the selected paper feed station. Zoom keys G Use to select any reduction or enlargement copy ratio from 50 to 200% in 1% increments. (p. 17) Copy quantity keys G Use to select the desired copy quantity (1 to 99). (p. 15) G Use to make user program entries. (p. 21) Clear key G Press to clear the display, or press during a copy run to terminate copying. (p. 15) G Press and hold down during standby to display the total number of copies made to date. (p. 22) Print key and ready indicator G Copying is possible when the indicator is on. G Use to set a user program.

COPIER INSTALLATION

Improper installation may damage the copier. Please note the following during initial installation and whenever the copier is moved. If the copier is moved from a cool place to a warm place, condensation may form inside the copier. Operation in this condition will cause poor copy quality and malfunctions. Leave the copier at room temperature for at least 2 hours before use.
Do not install your copier in areas that are:
damp, humid, or very dusty
exposed to direct sunlight

poorly ventilated

subject to extreme temperature or humidity changes, e.g., near an air conditioner or heater.
The copier should be installed near an accessible power outlet for easy connection. Be sure to connect the power cord only to a power outlet that meets the specified voltage and current requirements. Also make certain the outlet is properly grounded. Connect the copier to a power outlet which is not used for other electric appliances. If a lighting fixture is connected to the same outlet, the light may flicker.
Be sure to allow the required space around the machine for servicing and proper ventilation.

4" (10 cm)

8"(20 cm)
A small amount of ozone is produced within the copier during operation. The emission level is insufficient to cause any health hazard. NOTE: The present recommended long term exposure limit for ozone is 0.1 ppm (0.2 mg/m3) calculated as an 8 hr. time-weighted average concentration. However, since the small amount that is emitted may have an objectionable odor, it is advisable to place the copier in a ventilated area.

CAUTIONS ON HANDLING

Be careful in handling the copier as follows to maintain the performance of this copier.
Do not drop the copier, subject it to shock or strike it against any object.
Store spare toner cartridges in a cool dry place without removing from the package before use.
If they are exposed to direct sunlight or excessive heat, poor print quality may result.
Do not touch the photoconductive drum (green portion).
Scratches or smudges on the drum will cause dirty copies.

LOADING COPY PAPER

Raise the handle of the paper tray and pull the paper tray out until it stops.
Adjust the paper guides on the paper tray to the copy paper width and length. Squeeze the lever of paper guide and slide the guide to match with the width of the paper. to the appropriate slot as marked on the tray. Move paper guide

Paper guide B

Paper guide A
Fan the copy paper and insert it into the tray. Make sure the edges go under the corner hooks. Do not load paper above the maximum height line ( will cause a paper misfeed. ). Exceeding the line
Gently push the paper tray back into the copier.

NORMAL COPYING Original face up
B. When using the original table: (1) Open the original cover. (2) Place an original face down on the original table. Align it with the original scale and the centering ( ) mark. Close the original cover.

Original scale

When copying a book or an original which has been folded or a crumpled original, press down the original cover lightly. If the original cover is not securely closed, the copies may be striped or blurred.
A book, an original which has been folded, or a crumpled original
Select the desired original to copy mode. A. When copying in the one-sided to one-sided mode: Ensure that no indicator is lit among the original to copy indicators. B. When copying in a one-sided to two-sided mode: Use the original to copy key to select the desired one-sided to two-sided copying mode (Turn on Long Edge or Turn on Short Edge). See the illustrations on page 12. C. When copying in the two-sided to two-sided mode: Use the original to copy key to select the two-sided to two-sided copying mode. The originals must be set in the RSPF before this mode can be set (step 3).
D. When copying in the two-sided to one-sided mode: Use the original to copy key to select the two-sided to one-sided copying mode. The originals must have been set in the RSPF in step 3.
Ensure that the desired paper tray is selected.
Paper sizes that can be used in the duplex copy mode are letter, legal, and invoice. (When copying from the original table in the duplex copy mode, only letter size paper can be used.) G The bypass tray cannot be used in the duplex copy mode.
Set the number of copies using the two copy quantity ( , ) keys when copying from the original table or copying in a 1-sided copy mode from the RSPF.

Press the clear (

) key to clear an entry if a mistake is made.
A single copy can be made with the initial setting, i.e., when 0 is displayed.
Press the right copy quantity key to set the units digit from 0 to 9. This key will not change the tens digit. Press the left copy quantity key to set the tens digit from 1 to 9.

Tens digit

Units digit

Press the print (

) key.

To decrease or increase the zoom ratio rapidly, press and hold down the or key. However, the value will stop at the preset reduction or enlargement ratios. To move beyond these ratios, release the key and then press and hold it down again.
BYPASS FEED (including special paper)
The bypass tray can automatically feed up to 50 sheets of standard copy paper and can also feed special papers such as transparency film and labels one sheet at a time. Copy paper measuring from 3-1/2" x 5-1/2" to 8-1/2" x 14" and in the weight range of 14 to 34.5 lbs. can be used in this tray. (For paper weighing from 28 to 34.5 lbs., 8-1/2" x 11" is the maximum size.) Place the original(s) face up in the document feeder tray or face down on the original table.
The original image must be smaller than the paper or media for copying. If the original image is bigger than the paper or media, this may cause smudges on the edges of the copies. Open the bypass tray and extend the tray.
To close the bypass tray, perform step1 and then step 2 in the illustration and push the round projections at the right of the tray until the tray clicks into place.
Set the paper guides to the copy paper width. Insert the copy paper (print face down) all the way into the bypass tray.
Paper must be fed narrow side into the feed slot. Transparency film, labels, and other special purpose papers must be fed individually. G When copying onto transparency film, remove each copy promptly. Do not let copies stack up. G When loading an envelope, make sure that it is straight and flat.

BYPASS FEED

Print face
Press the tray select ( ) key to select the bypass tray. Set the number of copies if using standard copy paper. Press the print ( ) key.
This chapter describes the special functions of this copier. Use these functions as needed.
DESCRIPTION OF SPECIAL FUNCTIONS
Toner save mode (page 20)
Reduces toner consumption by approximately 10%.

Special functions

Power save modes (page 21)
The copier has two power save modes of operation: preheat mode and auto power shut-off mode.

Return the charger cleaner to its original position. Close the side cover by pressing the round projections near the side cover open button.
Turn the power switch on.
When copier is not in use
To prevent entry of dust and foreign matter, store the copier as follows. Remove the power cord and secure the copier using tape (four locations).
This chapter describes misfeed removal and troubleshooting.

MISFEED REMOVAL

When the misfeed ( ) indicator blinks or blinks in the display, the copier will stop because of a misfeed. If a misfeed occurs when using the RSPF, a number may appear in the display after a minus sign. This indicates the number of the originals that must be returned to the document feeder tray after a misfeed. Return the required number of originals. Then this number will disappear when copying is resumed or the clear ( ) key is pressed. When the RSPF misfeeds an original sheet, the copier will stop and the RSPF misfeed ( ) indicator will blink, while the misfeed ( ) indicator will remain off. For a misfeed of originals in the RSPF, see D Misfeed in the RSPF on page 30. Ensure that the bypass tray is open and then open the side cover while pressing the side cover open button.

Copier trouble?

Check the misfeed location. Remove the misfed paper following the instructions for each location in the illustration below. If blinks in the display, proceed to A Misfeed in the paper feed area. (p. 28)
If paper is misfed here, proceed to B Misfeed in the fusing area. (p. 28)
If the misfed paper is seen from this side, proceed to C Misfeed in the transport area. (p. 29)
If paper is misfed here, proceed to A Misfeed in the paper feed area. (p. 28)
A Misfeed in the paper feed area
Gently remove the misfed paper from the paper feed area as shown in the illustration. When blinks in the display and the misfed paper is not seen from the paper feed area, pull out the paper tray and remove the misfed paper. If the paper cannot be removed, proceed to B Misfeed in the fusing area. The fusing unit is hot. Do not touch the fusing unit when removing misfed paper. Doing so may cause a burn or other injury.
Do not touch the photoconductive drum (green portion) when removing the misfed paper. Doing so may damage the drum and cause smudges on copies. G If the paper has been fed through the bypass tray, do not remove the misfed paper through the bypass tray. Toner on the paper may stain the paper transport area, resulting in smudges on copies.

Blank copies

Power save ( indicator on.
Copies are too dark or too light.

_ 26 38

Dust, dirt, smudges appear on copies. Striped copies
Paper misfeeds frequently.
Paper curled or damp? Pieces of paper inside copier? Paper guides in the paper tray not set properly? Too much paper in the paper tray or bypass tray? Is the copy paper too heavy? Paper damp?
Images rub off the copy easily.

STATUS INDICATORS

When the following indicators light up or blink on the operation panel or the following alphanumeric codes appear in the display, solve the problem immediately referring to both the table below and the relevant page. Be sure to use only genuine SHARP parts and supplies.

Indication

Cause and remedy

See page: 32 _ 23 27

Developer replacement Steadily Developer is required. Contact your SHARP service center as soon as possible. required indicator lit Toner cartridge replacement required indicator Steadily Replacement of toner cartridge will be needed soon. Obtain a new cartridge. lit Blinking Toner cartridge must be replaced. Replace it with a new one.

Misfeed indicator

A misfeed has occurred. Remove the misfed paper referring to the description of Misfeed Blinking removal. The lower side cover may be open. If so, close it. Steadily Service by an authorized SHARP service technician is required. lit An original misfeed has occurred in the RSPF. Blinking Remove the misfed originals referring to the description of Misfeed in the RSPF. The paper tray is not installed properly. Push the tray into the copier securely.

_ 32 30

Maintenance indicator RSPF misfeed indicator
The paper tray indicator is blinking.
CH is blinking in the display. The toner cartridge is not installed. Install the toner cartridge. If CH is blinking even if the
cartridge is installed properly, contact your SHARP service center immediately.
CH is steadily lit in the

display.

Side cover is open. Close the side cover securely by pressing the round projections near the side cover open button. Paper tray or bypass tray is empty. Load copy paper. A misfeed has occurred in the paper tray or bypass tray. Remove the misfed paper.
P is blinking in the display.
The copier will not function. Turn the power A letter and a number appear switch off, remove the power cord from the outlet, and contact your SHARP service center. alternately.
The automatic exposure level can be adjusted to suit your copying needs. This level is set for copying from the original table and copying from the RSPF respectively. When adjusting the automatic exposure level for copying from the RSPF, place an original in the document feeder tray and make sure that the RSPF ( ) indicator lights up. When adjusting the level for copying from the original table, make sure that no original is left in the document feeder tray. Press the exposure mode selector key to select the photo ( ) mode.

Press and hold down the exposure mode selector key for approximately 5 seconds. The photo ( ) indicator will go out and the AUTO indicator will begin to blink. One or two exposure indicators corresponding to the automatic exposure level which has been selected will light up.
Press the light ( ) or dark ( ) key to lighten or darken the automatic exposure level as desired. If exposure level 2 is selected, the two left-handmost indicators for that level will light up simultaneously. Also, if level 4 is selected, the two right-handmost indicators for that level will light up simultaneously.
Press the exposure selector key. The AUTO indicator will stop blinking and light up steadily. This automatic exposure level will remain in effect until you change it again by this procedure.

SPECIFICATIONS

Type Copy system Originals Original size Copy sizes Digital laser copier, desk-top type Dry, electrostatic transfer Sheets, bound documents Max. 10" x 14" (5-1/2" x 8-1/2" to 10" x 14" for RSPF) 3-1/2" x 5-1/2" to 8-1/2" x 14" (Feed copy paper lengthwise only.) Image loss: Max. 5/32" (4 mm) (leading and trailing edges) Max. 11/64" (4.5 mm) (along the other edges in totals) Max. 15/64" (6 mm) (the trailing edge of the second copy of two-sided copying) 15 copies/min. Max. 99 copies; subtractive counter 9.6 s (normal copying mode) Variable: 50% to 200% in 1% increments (total 151 steps) Fixed: 50%, 64%, 78%, 100%, 129%, 200% Original table: Moving optical source, slit exposure (stationary platen) with automatic exposure RSPF: Moving original One paper tray with automatic feed (250 sheets); one bypass tray with 50-sheet automatic feed capability Heat rollers Magnetic brush development Xenon lamp Scan: 400 dpi Output: 600 dpi 6 MB
Copy speed (one-sided copying)

Appendix

Continuous copying First-copy time (Approximately) Copy ratio Exposure system
Copy paper feed Fusing system Development system Light source Resolution Memory
Power supply Power consumption Overall dimensions Weight (Approximately) Copier dimensions Operating conditions Noise level
AC 120V (10%), 60 Hz (2%) 1,000 W 31.9" (W) x 19" (D) (809 mm (W) x 483 mm (D)) 50.7 lbs. (23 kg) Toner cartridge included 20.4" (W) x 19" (D) x 15" (H) (518 mm (W) x 483 mm (D) x 379 mm (H)) Temperature: 50F to 86F (10C to 30C) Humidity: 20% to 85% Sound Power Level LWA Copying: 71 [dB (A)], Standby: Background noise level Sound Pressure Level LPA (bystander positions) Copying: 40 [dB (A)], Standby: Background noise level Noise emission measurement in accordance with ISO 7779. GDI expansion kit (AR-PG1) PCL expansion kit (AR-PB9) 250-sheet paper feed unit (AR-DE9)

Optional equipment

First-copy time may differ depending on operating conditions, such as power-supply voltage and room temperature. As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units.

SUPPLIES

Types and sizes of copy paper
For best results, use only paper recommended by SHARP. Type of paper feeding Paper tray Type of media Standard paper Size Letter (8-1/2" x 11") Legal (8-1/2" x 14") Invoice (5-1/2" x 8-1/2") A4 (210 mm x 297 mm) B5 (182 mm x 257 mm) A5 (148.5 mm x 210 mm) Letter (8-1/2" x 11") Legal (8-1/2" x 14") Invoice (5-1/2" x 8-1/2") A4 (210 mm x 297 mm) B5 (182 mm x 257 mm) A5 (148.5 mm x 210 mm) A6 (105 mm x 148.5 mm) Letter (8-1/2" x 11") A4 (210 mm x 297 mm) Commercial 10 (4-1/8" x 9-1/2") Monarch (3-7/8" x 7-1/2") International DL (110 mm x 220 mm) International C5 (162 mm x 229 mm) Weight 15 lbs. to 21 lbs.

Bypass tray

Standard paper and thick paper

14 lbs. to 34.5 lbs.**

Special Transparency media film

Envelope*

* Do not use envelopes that have metal clasps, plastic snappers, string closures, windows, linings, self-adhesive, patches or synthetic materials. These will cause physical damage to the copier. ** For paper weighing from 28 to 34.5 lbs., 8-1/2" x 11" is the maximum size that can be fed through the bypass tray. Special papers such as transparency film and labels must be fed one sheet at a time through the bypass tray.
Be sure to use only genuine SHARP parts and supplies.
For best copying results, be sure to use only SHARP Genuine Supplies which are designed, engineered, and tested to maximize the life and performance of SHARP copiers. Look for the Genuine Supplies label on the toner package.
Proper storage 1. Store the supplies in a location that is:
clean and dry, at a stable temperature, not exposed to direct sunlight.
2. Store copy paper in the wrapper and lying flat.
Paper stored out of the wrapper or in packages standing on end may curl or get damp, resulting in paper misfeeds.

SYSTEM CONFIGURATION

A number of options are available for the copier which allow you to configure a copier system to meet your particular needs. The options include the following.
GDI expansion kit (AR-PG1)* PCL expansion kit (AR-PB9)* * This option is not used for the copier operation. For description of this option, see the separate manual.

N Names operation panel. 7 part. 6 O ON LINE indicator. 7 Operation panel part names. 7 Options. 40 Original cover. 6 Original guides. 6, 13 Original table. 6, 14 P Paper loading. 10 special. 38 specifications. 38 Paper feed area. 28 Paper output tray. 6 Paper output tray extension. 6, 12 Paper size. 38 Paper transport area. 29 Paper tray. 6 Part names. 6 PCL expansion kit (AR-PB9). 37, 40 Photo mode. 7, 16 Power on. 13 Power save modes. 20, 21 Power switch. 6, 13 Preheat mode. 20, 21 Print key. 15
R Ready indicator. 7 Reduction. 17 Replacement toner cartridge. 23 Reversing single pass feeder (RSPF). 12 S Special paper. 38 Specifications copier. 36 paper. 38 Status indicators. 34 Storage of supply. 39 Stream feeding mode. 16, 21
T Toner cartridge indicator. 7, 34 life. 25 replacement. 23 Toner save mode. 20 Total number of copies. 22 Transfer charger. 6, 26 Troubleshooting. 33 Two-sided copying. 12 U User maintenance cabinet. original cover. original table. transfer charger.

Z Zoom. 17

Date Issued:Nov. 1, 2000
MATERIAL SAFETY DATA SHEET

MSDS No. F-01001

Section 1.

Product Identification

Product: AR-152NT/T/FT/ST (Black Toner)

Section 2.

Suppliers Name and Address
Sharp Corporation 22-22 Nagaike-cho, Abeno-ku, Osaka, Japan Local suppliers are listed below. Please contact the nearest supplier for additional information. (Country) U.S.A. (Name and Telephone Number) Sharp Electronics Corporation Telephone number for information: 1-800-237-4277 Emergency telephone number: 1-800-255-3924 Sharp Electronics of Canada Ltd. Telephone number for information: 905-890-2100 Emergency telephone number: 1-800-255-3924 Sharp Electronics (U.K.) Ltd. Telephone number for information: 01923-474013

Canada

United Kingdom

Section 3.

Ingredients
CAS No. 29497-14-1 1333-86-4 1309-38-2 109125-51-1 109125-50-0 84179-66-8 Proportion > 88 % < 6.0% < 4.5% < 1.5% OSHA PEL ACGIH TLV Other Limits Not listed Not listed None 3.5mg/m3 3.5mg/m3 None Not listed Not listed None 0.5mg/m3 0.5mg/m3 None
Ingredients Styrene-Acrylate copolymer Carbon black Iron oxide Metal Complex dye

Section 4.

Hazardous Identification (Emergency Overview)
Toner is a fine, black powder possessing no immediate hazard. There are no anticipated carcinogenic effects from exposure based on animal tests performed using toner. When used as intended according to instructions, studies do not indicate any symptoms of fibrosis will occur.

Section 5.

Health Hazard Data
Inhalation? Skin? Ingestion? Yes No Possible but very unusual. Health Hazards: Acute oral toxicity ------------- LDL0 of this toner is over 2,000mg/kg. Mutagenicity -------------------- The result of Ames test is negative. Carcinogenicity: In 1996 the IARC reevaluated carbon black as a Group 2B carcinogen (possible human carcinogen). This classification is given to chemicals for which there is inadequate human evidence, but sufficient animal evidence on which to base an opinion of carcinogenicity. The classification is based upon the development of lung tumors in rats receiving chronic inhalation exposures to free carbon black at levels that induce particle overload of the lung. Studies performed in animal models other than rats did not show any association between carbon black and lung tumors. Moreover, a two-year cancer bioassay using a typical toner preparation containing carbon black demonstrated no association between toner exposure and tumor development in rats. Chronic Effect: In a study in rats of chronic inhalation exposure to a typical toner, a mild to moderate degree of lung fibrosis was observed in 92% of the rats in the high concentration (16mg/m3) exposure group, and a minimal to mild degree of fibrosis was noted in 22% of the animals in the middle (4mg/m3) exposure group, but no pulmonary change was reported in the lowest (1mg/m3) exposure group, the most relevant level to potential human exposures. Signs and Symptoms of Exposure: Minimal irritation to respiratory tract may occur as with exposure to any non-toxic dust. Medical Conditions Generally Aggravated by Exposure: None Emergency and First Aid Procedures: Inhalation; Remove to fresh air. If effects occur, consult medical personnel. Eye; In case of contact, immediately flush eyes with water for 15 minutes.

Route(s) of Entry:

Section 6.
Physical Chemical Characteristics
Not applicable Not applicable Not applicable Not applicable Fine powder Odorless Specific Gravity: Solubility in Water: PH: Viscosity: Color: 1.1 Negligible Not applicable Not applicable Black
Boiling / Melting Point: Vapor Pressure: Vapor Density: Evaporation Rate: Appearance: Odor:

Section 7.

Fire and Explosion Data
Not applicable >350C (LEL); Not applicable (UEL); Not applicable CO2, dry chemical, foam or water None This material has no unusual fire or explosion hazards. None None
Flash Point (Method Used): Ignition Temperature: Flammable Limits: Extinguishing Media: Special Fire Fighting Procedure: Unusual Fire and Explosion Hazard: Sensitivity to Mechanical Impact: Sensitivity to Static Charge:

Section 8.

Reactivity Data
Stable None CO and NOx Will not occur.
Stability: Incompatibility (Material to Avoid): Hazardous Decomposition: Hazardous Polymerization:

Section 9.

Precautions for Safe Handling and Use
Personal Protection Information (Respiratory, Eye Protection and Protective Glove): Use of a dust mask is recommended when handling a large quantity of toner or during long term exposure, as with any non-toxic dust. Engineering Control / Ventilation: Not required. Work / Hygienic Practice: Inhalation should be minimized as with any non-toxic dust. Steps to be taken in case of Spill or Leak: Sweep up or clean up with vacuum cleaner. Waste Disposal Method: Waste material may be dumped or incinerated under conditions which meet all federal, state and local environmental regulations.

Section 10.

Regulatory Information
Health = 1 Flammability = 1 This product is not a controlled product. This product is not a hazardous material. None allocated. Reactivity = 0
NFPA Rating (U.S.A.): WHMIS Legislation (Canada): Transport Information: UN No.:

Section 11.

SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430-2135. www.sharp-usa.com

SHARP CORPORATION

PRINTED IN CHINA

2000M KS TINSE0464QSZZ

AR-F152
SHARP TROUBLE & ERROR CODES AR-151, AR-156, AR-F152

5. TROUBLE CODES

A. Trouble codes list
Main code E7 Sub code 01 Trouble content Duplex model memory setup error, memory not-detected error HSYNC not detected. CCD white level trouble CCD black level trouble Shading trouble (White correction) ASIC connection trouble Copy lamp disconnection trouble Abnormal output of laser Feeding is not completed within the specified time after starting feeding. Return is not completed within the specified time. Detail of trouble The memory is not set properly or the memory capacity is not set to the duplex setup (6M). Cancel method: Set SIM 26-39 code number to 2. LSU (laser diode, reception element, APC circuit) trouble LSU drive circuit (ASIC) trouble CCD drive circuit (CCD PWB, ASIC harness) trouble Copy lamp lighting trouble (Copy lamp, invertor PWB) CCD drive circuit (CCD PWB, ASIC, harness) trouble Dirt on white plate for scanning white level Improper connection between CPU and ASIC (pattern cut, improper connection of lead pin) Copy lamp or copy lamp drive circuit (invertor PWB) trouble Copy lamp disconnection LSU (laser diode, reception element, APC circuit) trouble LSU drive circuit (ASIC) trouble When the mirror base is returned for the specified time (6 sec) in mirror initializing after turning on the power, the mirror home position sensor (MHPS) does not turn OFF. Or when the mirror base is fed for the specified time (about 6 sec) after start of copy return, the mirror home position sensor (MHPS) does not turn OFF. When the mirror base is returned for the specified time (6 sec) in mirror initializing after turning on the power, the mirror home position sensor (MHPS) does not turn ON.Or when the mirror base is returned for the specified time (about 6 sec) after start of copy return, the mirror home position sensor (MHPS) does not turn ON. When the main motor encoder pulse is not detected for 100msec. The lock signal (specified rpm signal) does not return within a certain time (about 20sec) from starting the polygon motor rotation The fusing thermistor is open. The fusing temperature rises above 240C. The fusing temperature does not reach 185C within 27 sec of turning on the power, or the fusing temperature keeps at 140C. When the counter check sum value stored in the EEPROM is abnormal. When a communication trouble occurs with the EEPROM. Serial communication error when a communication trouble occurs with the CRUM IC. When a toner cartridge of different type is used. Error in data reception from the FAX board to the MCU. Occurs when the message header of the message format is other than F. Cancel method: Turn OFF/ON the power. Error in data reception from the FAX board to the MCU. Occurs when the odd number parity set with SMR (serial mode register) differs from the reception data. Cancel method: Turn OFF/ON the power. Error in data reception from the FAX board to the MCU Occurs when the next data reception is completed with RDRF (Receive Data Register Full) flag of SS (Reserial status register) set to 1. Cancel method: Turn OFF/ON the power. Error in data reception from the FAX board to the MCU. Occurs when the stop bit is 0. (The stop bit must be 1.) Cancel method: Turn OFF/ON the power. Occurs when time is out without response in data communication between the FAX board and the MCU. Cancel method: Turn OFF/ON the power. Communication trouble between the MCU and the FAX board or between the FAX board and the FAX panel Cancel method: Turn OFF/ON the power. Check connections.

E7 E7 E7 E7 E7 E7 E7

L4 L6 H2 H3 H4 U2 U2 U2 F2 F6

Main motor lock Polygon motor lock Thermistor open detection Heat roller abnormally high temperature Heat roller abnormally low temperature Counter sum check error EEPROM serial communication error CRUM IC Toner cartridge type error Communication trouble with FAX PWB (Protocol) Communication trouble with FAX PWB (Parity)
Communication trouble with FAX PWB (Overrun)
Communication trouble with FAX PWB (Framing) Communication trouble with FAX PWB (Time-out) FAX PWB trouble
B. FAX Service Error Code Table
(1) LCD: FAX SERVICE ERROR(#)
Code # 1 RAM error 2 CTS error (Communication error) 3 Content ROM error Remedy Turn OFF/ON the power. If the error is not canceled, check the ROM of the FAX PWB. Turn OFF/ON the power. If the error is not canceled, check the DRAM of the FAX PWB. Turn OFF/ON the power. If the error is not canceled, check connection between the FAX PWB and the MCU PWB. If no abnormality is found, check the FAX PWB and MCU PWB themselves., especially TXD, RXD, CTS, and RTS signals. Turn OFF/ON the power. If the error is not canceled, check the connector and the harness between the FAX PWB and the MCU PWB. If no abnormality is found, check the FAX PWB and MCU PWB themselves. Turn OFF/ON the power and execute FAX scanning to check the operation. If the error is not canceled. Check connection between the FAX PWB and the MCU PWB. If no abnormality is found, check the FAX PWB and MCU PWB themselves.

(2) Reception error

Code 0 Content The handshake signal is detected, but the signal includes an error. The handshake signal from the receiver is not recognized. (Error after reception of NSF/DIS) The handshake signal from the receiver is not recognized. (Error after reception of NSC/DTC) The handshake signal from the receiver is not recognized. (Error after reception of EOP) The handshake signal from the receiver is not recognized. (Error after reception of EOM) The handshake signal from the receiver is not recognized. (Error after reception of MPS) Not defined. An unexpected DCN is received. Error after reception of all pages (Error after reception of PPS-EOP) Error after changing the communication mode (Error after reception of PPS-EOM) Error after reception of a page (Error after reception of PPS-MPS/NULL) Not defined. Communication error after fallback during transmission (Error after reception of CTC) Error after reception of EOR & errors other than the above

Panel error

Scan data error
Note: If some reception data is left in memory,, transfer the data with FUNCTION-0 and turn OFF the power.

C. Communication error code table

(1) Sending error

Code 0 Content The handshake signal is detected, but the signal includes an error. The handshake signal from the receiver is not recognized. (Error after reception of NSF/DIS) The line is disconnected during data transmission. The line is disconnected after fallback of training. (Error after reception of CFR) The line is disconnected during transmission of two or more pages. (Error after reception of MCF) Not defined. Error after reception of RTN/RTP An unexpected DCN is received. Resend is repeated by the specified times, but the error is not canceled. Not defined. Not defined. Not defined. Error after fallback during transmission (Error after reception of CTR) ERR is received, & errors other than the above.