AR-201

DIGITAL COPYING MACHINE OPERATION MANUAL
GETTING STARTED MAKING COPIES STATUS INDICATORS GENERAL INFORMATION OPTIONAL EQUIPMENT

CAUTIONS

Follow the cautions below when using this copier.
The fusing area is hot. Exercise care in this area when removing misfed paper. Do not look directly at the light source. Doing so may damage your eyes.
Place the copier on a firm, level surface. Do not install the copier in a humid or dusty location. When the copier is not used for a long time, for example, during prolonged holidays, turn the power switch off and remove the power cord from the outlet. When moving the copier, be sure to turn the power switch off and remove the power cord from the outlet. Do not cover the copier with a dust cover, cloth or plastic film while the power is on. Doing so may prevent heat dissipation, damaging the copier. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous laser radiation exposure.

Cautions on laser

Wave length Pulse times Output power 785 nm 10 nm (8.141 s 0.1 s)/7 mm 0.2 mW 0.02 mW

CONTENTS

GETTING STARTED
INTRODUCTION. 2 MAIN FEATURES. 3 PART NAMES AND FUNCTIONS. 4 Overall layout. 4 Operation panel. 6 COPIER INSTALLATION. 8 CAUTIONS ON HANDLING. 9 LOADING COPY PAPER. 10

MAKING COPIES

q q q q q q q q q q q
AUDITING ACCOUNTS. NORMAL COPYING. REDUCTION/ENLARGEMENT/ZOOM. BYPASS FEED (special paper). TWO-SIDED COPYING. XY ZOOM. B/W REVERSE. DUAL PAGE COPY. INTERRUPTING A COPY RUN. AUTOMATIC EXPOSURE ADJUSTMENT. TONER SAVE MODE.

STATUS INDICATORS

q q q q
TONER CARTRIDGE REPLACEMENT. MISFEED REMOVAL. DEVELOPER REQUIRED. MAINTENANCE REQUIRED.

GENERAL INFORMATION

q q q q q
USER PROGRAMS. Settings for auditing accounts. POWER SAVE MODES. USER MAINTENANCE. COPIER TROUBLE?. SUPPLIES. Types and sizes of copy paper. Genuine supplies statement. SPECIFICATIONS.

OPTIONAL EQUIPMENT

SYSTEM CONFIGURATION. SINGLE PASS FEEDER (AR-SP2). ELECTRONIC SORTING KIT (AR-EB3). Sort/group. 2 in 1 or 4 in 1. Erase. Margin shift. 250-SHEET PAPER FEED UNIT (AR-DE5)/ 2x250-SHEET PAPER FEED UNIT (AR-DE6).

INDEX.

INTRODUCTION
GETTING STARTED Introduction
This copier has been designed to provide convenient copying features in a minimum amount of office space and with maximum operational ease. To get full use of all copier features, be sure to familiarise yourself with this manual and the copier. For quick reference during copier use, keep this manual in a handy location. This copier can be used as a laser printer and as a facsimile machine by installing optional components. However, this manual describes only the copier features. For description of the printer features and facsimile features, see their separate manuals. (Some options may not be available in some countries.)
Conventions used in this manual
In this manual, the following icons are used to provide the user with information pertinent to the use of the copier. Warns the user that injury to the user or damage to the copier may result if the contents of the warning are not properly followed. Cautions the user that damage to the copier or one of its components may result if the contents of the caution are not properly followed. Notes provide information relevant to the copier regarding specifications, functions, performance, operation and such, that may be useful to the user. Indicates a letter displayed in the copy quantity display.
AB series (metric) and inch series references

[AB series]

Both specifications are quoted where applicable.

[Inch series]

The inch series specifications are quoted in brackets. For example: Page 18, step 1 --------- B4 or A3 (8-1/2" x 14" or 11" x 17") Page 17, step 2-A ------ 86%, 81%, 70%, and 50% (95%, 77%, 64%, and 50%) Although AB series size indications are shown on the operation panel of this manual, inch series indications are displayed on the inch series machines.

MAIN FEATURES

High-speed laser copying q First-copy time is only 7.2 seconds (except in a power save mode or immediately after power on).
Copying speed is 20 copies/min., which adapts to business use, allowing improvement of working efficiency.
High-quality digital image q High-quality copying at 600 dpi is performed.
In addition to the automatic exposure mode, the manual exposure can be adjusted in five steps. The photo mode copying function allows clear copying of delicate halftone original images such as monochrome photos and colour photos. Photo mode is adjustable in five steps.

AUTO PAPER SELECT ( ) indicator Paper of the proper size will be automatically selected depending on the original size and selected copy ratio when this indicator is on.

COPIER INSTALLATION

GETTING STARTED Copier installation
Improper installation may damage the copier. Please note the following during initial installation and whenever the copier is moved. If the copier is moved from a cool place to a warm place, condensation may form inside the copier. Operation in this condition will cause poor copy quality and malfunctions. Leave the copier at room temperature for at least 2 hours before use. Do not install your copier in areas that are:
damp, humid, or very dusty
exposed to direct sunlight

poorly ventilated

subject to extreme temperature or humidity changes, e.g., near an air conditioner or heater.
The copier should be installed near an accessible power outlet for easy connection.
Be sure to connect the power cord only to a power outlet that meets the specified voltage and current requirements. Also make certain the outlet is properly grounded.
For this copiers power supply requirements, see the name plate located on the back of the unit. Connect the copier to a power outlet which is not used for other electric appliances. If a lighting fixture is connected to the same outlet, the light may flicker.

10 cm (4")

Be sure to allow the required space around the machine for servicing and proper ventilation.

CAUTIONS ON HANDLING

Be careful in handling the copier as follows to maintain the performance of this copier.
Do not drop the copier, subject it to shock or strike it against any object.

Cautions on handling

Store spare toner cartridges in a dark place without removing from the package before use. If they are exposed to direct sunlight, poor copies may result.
Do not touch the photoconductive drum (green portion). Scratches or smudges on the drum will cause dirty copies.

LOADING COPY PAPER

GETTING STARTED Loading copy paper
To save space, this copier has been designed with adjustable front-loading trays, which are easily opened for paper loading. For best results, use only SHARP recommended paper. (See page 50.) The paper required ( ) indicator will light up when there is no copy paper in the selected paper feed station, or when the selected paper tray is not installed or is improperly installed. When the paper size is changed in a paper tray, the size of the paper must be entered by steps 8 through 11 on page 12. If not, the edges of copies may become smudged with toner. Also, the AUTO PAPER SELECT and the AUTO IMAGE features will not function properly.

Gently lift and pull out the paper tray until it stops.
Push the pressure plate down until it locks in place.
Fan the copy paper and insert it into the tray. Make sure the edges go under the corner hooks.
If you change to a different size of copy paper, the tray must be adjusted. See the next page.

Maximum height line

Set the paper along the guides. The tray holds up to 250 sheets of paper. Do not load paper above the maximum height line.
Push the paper tray firmly back into the copier.
Changing the copy paper size in the tray

Left guide

Front guide
Squeeze the lock lever of the front guide and slide the front guide to match the width of the paper.
Move the left guide to the appropriate slot as marked on the tray.
When using A5 (5-1/2" x 8-1/2") copy paper, load it into the uppermost paper tray. If other trays (including trays in optional paper feed units) are used, paper misfeeds may occur. With inch system machines, when using 11" x 17" copy paper, store the left guide in the slot at the left front of the paper tray.
Load copy paper into the tray. Place the appropriate label to indicate the selected paper size into the recess on the right front side of the paper tray. Push the paper tray firmly back into the copier.
To set the selected paper size, press the PAPER SIZE ) key. ENTER (
The selected paper feed location indicator will blink and the corresponding paper size (which is currently set) indicator will light up steadily. All other indicators will go out. For paper size setting, ensure that the COPY mode has been selected. However, if copying, printing or facsimile printing is being performed, paper size setting cannot be made even in the COPY mode. See Note on page 48.
Use the TRAY SELECT ( ) key to select the paper tray of which the paper size has been changed.
Each time the TRAY SELECT ( ) key is pressed, a paper tray will be indicated with a blinking paper feed location indicator.
Use the ORIGINAL SIZE ENTER ( the paper size which is set.

) key to select

Each time the ORIGINAL SIZE ENTER ( ) key is pressed, a paper size will be indicated with a paper size indicator.

Press the START ( ) key and then the PAPER SIZE ENTER ( ) key.
To change the paper size setting of another tray, repeat steps 9 to 10 after pressing the START ( ) key.

AUDITING ACCOUNTS

If this copier has been programmed in the auditing mode, it will not function until an assigned 3-digit account number has been entered. See page 39 for setting the auditing mode.
MAKING COPIES Auditing accounts
If the copier has been programmed in the auditing mode, will appear in the copy quantity display in the initial conditions.
Enter your account number using the numeric keys.
As each digit is entered, the dashes in the copy quantity display will disappear. After the number is entered, the copy quantity display will change to 0. If an unassigned number is entered, will appear again in the copy quantity display, indicating that the number was not accepted.
When copying is completed, press the AUDIT CLEAR ( ) key.
will appear again in the copy quantity display, indicating the auditing mode. In the interrupt copy mode (see page 25), press the INTERRUPT ( ) key after an interrupt copy run is completed. All previous copier settings will be restored and the previous account number will be active.

NORMAL COPYING

Power on
Turn the power switch on.
It will take about 35 seconds for the copier to warm up. However, you can make desired settings and press the START ( ) key during warm-up. Copying will start after warm-up. If the copier has been programmed in the auditing mode, the START key ( ) indicator will not light up and will appear in the copy quantity display. Enter an assigned 3-digit account number. See page 13. If the power is already on and all indicators except the POWER SAVE ( ) indicator are off, the copier is in the auto power shut-off mode. Press the START ( ) key in this case. See page 43, POWER SAVE MODES.

Normal copying

Place the original face down on the original table. Align it with the original size scale.
The ORIGINAL SIZE indicator for the size detected will light up. Image loss (max. 4 mm (5/32")) can occur at the leading and trailing edges of the copies. Also image loss (max. 4 mm (5/32") in total) can occur along the other edges of the copies.

Close the platen cover.

Paper matching the size of the original will be automatically selected when the auto paper select function is enabled. To copy onto paper of a different size, press the TRAY SELECT ( ) key. The auto paper select function can be disabled using user program No. 8. If this function is disabled, use the TRAY SELECT ( ) key to select the desired paper tray. See page 36, USER PROGRAMS. The bypass tray cannot be automatically selected. In some areas, 8-1/2" x 13" sized paper can be used as standard sized paper. However, an original of this size will be sensed as A4R. 8-1/2" x 13" size can be specified by using the ORIGINAL SIZE ENTER key.
Ensure that the desired paper tray is selected.

Adjust the copy density.

This copier has three exposure modes to choose from AUTOMATIC ( ), MANUAL ( ), and PHOTO ( ). Automatic exposure is the standard initial setting for this copier. In this mode, the characteristics of the original are read by the exposure system and adjustments are automatically made. This optimizes the contrast of the copied images by reducing the effect of coloured or shaded background areas. See page 26 to adjust the automatic exposure level.
For manual copy density adjustment, press the AUTO/MANUAL/ PHOTO ( / / ) key to select MANUAL ( ) and adjust with the light ( ) and dark ( ) keys as desired.
For photographs, select PHOTO ( ) and then adjust with the light ( ) and dark ( ) keys as desired. There are 5 exposure steps indicated by 3 indicator lights. (The indicators light up one or two at a time.) If exposure level 2 is selected, the two left-handmost indicators for that level will light up simultaneously. Also, if level 4 is selected, the two right-handmost indicators for that level will light up simultaneously.
Set the number of copies using the numeric keys.
A single copy can be made with the initial setting, i.e., when 0 is displayed. Press the CLEAR ( ) key to clear an entry if a mistake is made.

Press the START (

) key.
The number in the copy quantity display will decrease by 1 each time a copy is made. Press the CLEAR ( ) key to stop copying in the middle of a run. To repeat the same copy sequence for a different original, simply replace the original and press the START ( ) key. If the paper in the selected tray runs out during the copy run and no other tray contains the same size paper, the bypass tray can be selected using the TRAY SELECT ( ) key.

Replace the first original with the second original and close the platen cover.
Make sure that the first and second originals are oriented in the same way on the original table. When the originals are placed horizontally, make sure that the first and second originals are oriented in the reverse way on the original table.
Turn the first copy over left to right and place it into the bypass tray.
Be sure to feed the copies one sheet at a time. Depending on the copy paper quality, the copy may curl up. If the copy has curled up, be sure to perform the following steps before copying onto the reverse side to avoid a misfeed. 1. Flatten the copy paper. 2. Change the orientation of the original and copy paper. (For example, change A4 (8-1/2" x 11") to A4R (8-1/2" x 11"R).)
Use the TRAY SELECT ( Press the START (
) key to select the bypass tray.

XY ZOOM

Original Copy
The XY ZOOM feature allows the horizontal and vertical copy ratios to be changed independently. This feature cannot be used with the 2 in 1 or 4 in 1 feature. (The 2 in 1 or 4 in 1 feature can only be used when an optional electronic sorting kit and an optional SPF are installed.) To use the XY ZOOM feature with the DUAL PAGE COPY feature, set the DUAL PAGE COPY feature first and then the XY ZOOM feature. (Enlargement cannot be set.)

XY zoom

Press the XY-ZOOM ( ) key.
The current value for the vertical direction will be displayed in the copy quantity display.
Use the PRESET RATIO selector ( , ) keys and zoom ( , ) keys to change the copy ratio in the vertical direction.
Press a PRESET RATIO selector ( or ) key to set an approximate ratio, then press the key to decrease the ratio or key to increase the ratio. The copy ratio will be displayed in the copy quantity display.
Press the copy ratio display (
The selected ratio for the vertical direction will be entered and the current value for the horizontal direction will be displayed in the copy quantity display.

MAKING COPIES XY zoom

Use the PRESET RATIO selector ( , ) keys and zoom ( , ) keys to change the copy ratio in the horizontal direction in a similar manner as for the vertical direction.
The selected ratio for the horizontal direction will be entered and the display will change to the copy quantity display. To verify the copy ratios, press and hold down the copy ratio display ( ) key. The vertical and horizontal ratios will be alternately displayed.
Enter the desired number of copies.
To change the copy ratios again, press a PRESET RATIO selector ( , ) key or a zoom ( , ) key. Then, perform step 3 and the succeeding steps. To cancel this function, press the XY-ZOOM ( ) key again.

The previous copy quantity, copy ratio, copy density, and paper size will be automatically restored.
Replace the original(s) for the interrupted job on the original table or in the SPF and press the START ( ) key.
AUTOMATIC EXPOSURE ADJUSTMENT
The automatic exposure level can be adjusted to suit your copying needs. This level is set for copying from the original table and copying from the optional SPF respectively. To set the level for the optional SPF, place an original in the document feeder tray and make sure that the SPF indicator lights up before proceeding to step 1. To set the level for the original table, ensure that the SPF indicator does not light up.
MAKING COPIES Automatic exposure adjustment
Press the AUTO/MANUAL/PHOTO ( select the PHOTO ( ) mode.

) key to

Press and hold down the AUTO/MANUAL/PHOTO ( / ) key for approximately 5 seconds.
The PHOTO ( begin to blink.
) indicator will go out and the AUTO indicator will
One or two exposure indicators corresponding to the current automatic exposure level will light up. The factory default setting is level 3.
Press the light ( ) or dark( ) key to lighten or darken the automatic exposure level as desired.
Press the AUTO/MANUAL/PHOTO (
The AUTO indicator will stop blinking and will light up steadily. This automatic exposure level will remain in effect until you change it again by this procedure.

TONER SAVE MODE

This mode reduces toner consumption by approximately 10% in the automatic and manual exposure modes. Copies will be lighter but still adequate for general use. Selection of this mode does not affect the PHOTO mode. Follow the procedure below for setting the toning level.
Press the AUTO/MANUAL/PHOTO ( ) mode. select the MANUAL (

Toner save mode

The MANUAL ( ) indicator will go out and the PHOTO ( indicator will begin to blink.
The exposure indicator marked 5 will light up, indicating that the standard toner mode is active.
To enter the toner save mode, press the light (
The exposure indicator marked 1 will light up, indicating that the toner save mode is selected.
The PHOTO ( ) indicator will stop blinking and will light up steadily. The toner save mode is now active. To return to the standard mode, repeat the procedure but use the dark ( ) key to select exposure level 5 in step 3.
TONER CARTRIDGE REPLACEMENT
When the toner cartridge replacement required ( ) indicator lights up, replacement of the toner cartridge will be needed soon. Obtain a new cartridge. When the toner cartridge replacement required ( ) indicator blinks, the tonesr cartridge must be replaced before copying can be resumed. Replace the toner cartridge by following the procedure below. During a long copy run of a dark original, the indicator may blink and the copier stop, even though toner is left. The copier will feed toner up to 2 minutes and then the START key ( ) indicator will light up. Press the START ( ) key to restart copying. For best copying results, be sure to use only SHARP products. The package of SHARP toner has the Genuine Supplies label.

GENERAL INFORMATION User programs
* These programs do not affect the copier functions unless certain optional equipment is installed.
Setting the user programs
Press and hold the light ( ) key for more than 5 seconds until all the alarm indicators ( , , , , ) blink and appears in the copy quantity and display.
Enter a program number using the numeric keys.
The selected program number will blink in the copy quantity display. If a mistake is made in steps 2 to 4, press the CLEAR ( copier will return to step 2. The program numbers are shown in the table below. For example, to change the setting of the auto power shut-off timer, press key 3. Program name Auto clear time Preheat mode Auto power shut-off timer Stream feeding mode Auto power shut-off setting Border line for 2 in 1 or 4 in 1 Rotation copy Auto paper select mode Auto tray switching Auditing mode Account number entry Account number change Account number deletion Number of copies per account Resetting account Erase width adjustment Layout in 2 in 1 copy Layout in 4 in 1 copy Offset of paper output tray Program No. 19 ) key. The
For operation of these programs after step 3, see page 39.

User programs

For programs 1 to 9 and 16 to 19, the entered program number will be steadily lit on the left side of the copy quantity display and the currently selected parameter number for the program will blink on the right side. For programs 10 to 15 (programs for auditing accounts), the display varies with the program number. See page 39 for setting programs 10 to 15.
Select the desired parameter using the numeric keys.
The entered parameter number will blink on the right side of the copy quantity display. The parameters are shown in the table below. For example, to change the setting of the auto power shut-off timer to 60 min., press key 2.
Program name Auto clear time
Parameters 0 OFF sec. sec. Preheat mode** 0 OFF ** sec. Auto power shut-off timer *min. min. Stream feeding mode *0 OFF 1 ON Auto power shut-off setting 0 OFF *1 ON Border line for 2 in 1 or 4 in 1 * 0 OFF 1 ON Rotation copy 0 OFF *1 ON Auto paper select mode 0 OFF *1 ON Auto tray switching 0 OFF *1 ON Erase width adjustment mm mm (0 0" 1 1/4" Layout in 2 in 1 copy *1 Pattern Pattern 2 Layout in 4 in 1 copy *1 Pattern Pattern 2 Offset of paper output tray 0 Upper OFF, lower OFF 2 Upper ON, lower OFF

60 sec. 60 sec. 90 min.

3 *3 4

90 sec. 90 sec. 120 min.

120 sec. 120 sec. 240 min.

USER MAINTENANCE

Proper care is essential for clean, sharp copies. Please take a few minutes to regularly clean your copier.
Original table and platen cover
Stains or dirt on the original table or platen cover will also be copied. Wipe the original table and platen cover with a soft, clean cloth.
If necessary, dampen the cloth with water. Do not use thinner, benzene, or similar volatile cleaning agents.
If an optional SPF is installed, wipe the scanning window on the original table.
Bypass tray paper feed roller
If misfeeds occur frequently when feeding postcards, envelopes, thick paper, etc. through the bypass tray, wipe the blue paper feed roller at the feed slot of the bypass tray with a soft, clean cloth dampened with alcohol or water.

User maintenance

Paper feed roller
Transfer charger cleaning
If copies start becoming streaky or blotchy, the transfer charger may be dirty. Clean the charger using the following procedure.

Charger cleaner

GENERAL INFORMATION User maintenance
Turn the power switch off.
Gently lift and pull out the upper paper tray and take the charger cleaner out by holding the tab.
Set the charger cleaner onto the transfer charger and gently slide the cleaner in the direction indicated by the arrow two or three times.
Slide the charger cleaner from one end to the other end along the groove of the transfer charger. If the cleaner is stopped on the way, smudges on copies may occur.
If the white sheet metal is smudged with toner, wipe it with a soft, clean cloth.
Return the charger cleaner to its original position. Close the upper paper tray. Close the side cover by pressing the handle on the cover. Turn the power switch on.

COPIER TROUBLE?

Problem

Solution

Copier plugged in? Plug the copier into a grounded outlet. See page 8. Turn the power switch ON. See page 14. See pages 14 and 26.

Copier does not operate.

Power switch ON?
Copies are too dark or too light. Blank copies
Copy density properly adjusted?
Is the original placed face down? Paper too heavy?
Place the original face down on the original table. Use copy paper within the specified range. See page 50. Replace with dry copy paper. Be sure to store copy paper in a dry location. See page 51. Clean the transfer charger. See page 46.

Copies smear if rubbed.

Side cover(s) is open. Close the front and side covers securely.

indicator blinking?

The toner cartridge must be replaced. See page 28, toner CARTRIDGE REPLACEMENT.
A misfeed has occurred. See page 30, MISFEED REMOVAL.
Lighting fixture flickers.
Is the same power outlet used for the lighting fixture and the copier?
Connect the copier to a power outlet which is not used for other electric appliances.
Be sure to use only genuine SHARP parts and supplies.
Please contact your SHARP service centre immediately if a problem persists after checking the above.

Self-diagnostic function

An automatic self-diagnostic function is built into the copier. Should the copier malfunction, the self-diagnostic function will locate the problem and stop the copier to prevent damage. An alphanumeric code will appear in the copy quantity display. Example Should the copier completely stop and a letter and a number appear alternately, contact your SHARP service centre immediately.

SUPPLIES

Types and sizes of copy paper
Size Paper trays A5* to A3 (5-1/2" x 8-1/2"* to 11" x 17") Ordinary paper: A6 to A3 (5-1/2" x 8-1/2" to 11" x 17") Envelopes: International DL (110 x 220 mm) International C5 (162 x 229 mm) Commercial 10 (4-1/8" x 9-1/2") Weight 56 to 80 g/m2 (15 lbs. to 21 lbs.) Capacity (80 g/m2 (21 lb.) paper) 250 sheets Special paper

Bypass tray

56 to 128 g/msheets (15 lbs. to 34 lbs.)** (Ordinary paper)
Transparency film, labels, envelopes***
* A5 (5-1/2" x 8-1/2") copy paper can be used in the uppermost paper tray but cannot be used in other trays (including trays in optional paper feed units). ** For paper weighing from 105 to 128 g/m2 (28 to 34 lbs.), A4 (8-1/2" x 11") is the maximum size that can be fed through the bypass tray. *** Do not use envelopes that have metal clasps, plastic snappers, string closures, windows, linings, self-adhesive patches or synthetic materials. These will cause physical damage to the copier.

Location C

Roller
If the misfed original cannot be removed in steps 1 and 2, remove the misfed original from the exit area. Open the document feeder cover and rotate the roller in the direction indicated by the arrow if needed. If the misfed original cannot be easily removed from the exit area, open the front part of the document feeder tray to remove the original.
Open and close the document feeder cover to cancel the misfeed location indicator.
After misfed originals are removed, a number may appear in the copy quantity display, indicating the number of originals that must be returned to the document feeder tray. Return the originals and press the START ( ) key to resume copying.
ELECTRONIC SORTING KIT (AR-EB3)
If an electronic sorting kit (AR-EB3) is installed, the copier can perform several additional useful functions. These functions are 2 in 1 and 4 in 1, erase, margin shift, and sort/group functions. Also, rotation copying can be performed and a multiple number of originals can be scanned and stored into the memory. The memory can be expanded by adding commercially available memories recommended by SHARP. For details, contact your dealer. To use the 2 in 1 or 4 in 1 and sort/group functions, an optional SPF (AR-SP2) is needed. When installing an electronic sorting kit, it is recommended to install a single pass feeder.

Rotation copying

If user program No. 7 is set, the image of the original will rotate when the orientation of the original does not match that of the copy paper. Rotation copying will function only if the AUTO PAPER SELECT mode or AUTO IMAGE mode has been selected. Even if user program No. 7 is not set, rotation copying will function when the 2 in 1 or 4 in 1 function is selected. See page 36. However, if enlargement copying onto a paper size larger than A4 (8-1/2" x 11") is performed, the image cannot be rotated. When this occurs, the detected size and orientation of the original will be indicated by a steadily lighted indicator and a flashing indicator will show the required orientation of the original. The original must be rotated 90 to match the flashing indicator to prevent image loss on the copies.
Electronic sorting kit (AR-EB3) OPTIONAL EQUIPMENT
Example: Copying from an A3 (11" x 17") original onto A4 (8-1/2" x 11") paper

Original Paper Copy

Sort/group
If an optional electronic sorting kit is installed, the copier will have two sorter modes for different copying jobs: one sorts copies into sets matching the sequence of the originals and the second groups copies by originals. The sort/group feature cannot be used with the dual page copy feature. / ) key to select To change the SORT/GROUP mode, press the SORT/GROUP ( the desired mode. q The capacity of the paper output tray is 250 sheets (150 sheets if an optional job separator tray kit (AR-TR2) is installed). When the number of copies output reaches this limit in a sort or a group copy run, copying will stop, the output tray full ( ) indicator will light and the START key ( ) indicator will blink. Remove the copies from the paper output tray and press the START ( ) key to resume copying.

Suppliers

Name and Address
CAS No. 7439-89-6 29497-14-1 1333-86-4 Proportion > 92.5% < 7.0% < 0.5% OSHA PEL Not listed Not listed 3.5mg/m3 ACGIH TLV Not listed Not listed 3.5mg/m3 Other Limits None None None
Ingredients Iron powder Styrene-Acrylate copolymer Carbon black
Developer is a black powder containing small amounts of toner, and possessing no immediate hazard. There are no anticipated carcinogenic effects from exposure based on animal tests performed using toner.
Inhalation? Skin? Ingestion? No No Possible but very unusual. Health Hazards: Acute oral toxicity ------------ LDL0 of this toner which is included in this developer is over 2,000mg/kg. Mutagenicity ------------------ The toner, which is included in this developer, has been tested on Ames test. The result is negative. Carcinogenicity: In 1996 the IARC reevaluated carbon black as a Group 2B carcinogen (possible human carcinogen). This classification is given to chemicals for which there is inadequate human evidence, but sufficient animal evidence on which to base an opinion of carcinogenicity. The classification is based upon the development of lung tumors in rats receiving chronic inhalation exposures to free carbon black at levels that induce particle overload of the lung. Studies performed in animal models other than rats did not show any association between carbon black and lung tumors. While there have been no studies to date using developer, a two-year cancer bioassay using a typical toner preparation containing carbon black (a small amount of toner is included in the developer mixture) demonstrated no association between toner exposure and tumor development in rats. Signs and Symptoms of Exposure: Minimal irritation to respiratory tract may occur as with exposure to any non-toxic dust. Medical Conditions Generally Aggravated by Exposure: None Emergency and First Aid Procedures: Inhalation; Remove to fresh air. If effects occur, consult medical personnel. Eye; In case of contact, immediately flush eyes with water for 15 minutes.
Not applicable Not applicable Not applicable Not applicable Fine powder Odorless Specific Gravity: Solubility in Water: PH: Viscosity: Color: about 7.3 Negligible Not applicable Not applicable Black
Personal Protection Information (Respiratory, Eye Protection and Protective Glove): None required under normal use. Engineering Control / Ventilation: Not required. Work / Hygienic Practice: Not required. Steps to be taken in case of Spill or Leak: Sweep up or clean up with vacuum cleaner. Waste Disposal Method: Waste material may be dumped or incinerated under conditions which meet all federal, state and local environmental regulations.

SHARP AR-201 IMAGER. A DVA N C E D D I G I TA L D O C U M E N T S Y S T E M
HIGH RESOLUTION 1200 DPI-QUALITY/PCL6
SUPER G3. 6 K B P S FA X O P T I O N

NETWORK PRINTER OPTION

PA G E P E R M I N U T E
D I G I TA L C O P I E R W I T H 600 DPI OUTPUT
PRODUCTIVE SCAN ONCE, P R I N T M A N Y C A PA B I L I T Y
W I D E R A N G E O F PA P E R S I Z E S I N C L U D I N G 11 X 17
C O P Y, P R I N T, F A X. T H R E E S O L U T I O N S I N O N E R E L I A B L E S Y S T E M.
The Sharp AR-201 Digital IMAGER offers state-of-the-art, integrated office technology with three smart solutions in one crisp digital copying with scan once print many capability, advanced printing, and high-speed faxing. Taking advantage of the cost-efficient conventional supply system (separate toner, developer, and drum), the AR-201 IMAGER can reduce your total cost of ownership. The versatile digital copier includes advanced features like standard Auto Image Rotation Copy, Offset Stacking, Electronic Sorting Upgrade, and an optional Job Separation Tray. When youre ready for more, the AR-201 IMAGER can become a powerful high resolution 1200 dpi-quality network printer offering a wide range of paper sizes including 11 x 17. Use the optional Network Interface Card to maximize the efficiency and productivity of your workgroup delivering a range of output options right from your desktop. Plus, the optional Fax Expansion Kit turns the AR-201 IMAGER into a Super G3 plain-paper laser fax, with a 3 second per page transmission and 33.6 modem speed. The Sharp AR-201 Digital IMAGER is the all-in-one solution for any growing business looking for a competitive advantage.

AR -201

S P E C I F I C AT I O N S

COPIER SPECIFICATIONS

TYPE COPY SYSTEM ORIGINALS ORIGINAL SIZE (MAX) COPY SIZE (MIN/MAX) COPYING SPEED
Digital copying machine, desktop Dry electrostatic transfer system Sheets, bound documents 11" x 17" Min. 5 1/2" x 8 1/2", Max. 11" x 17" 20 copies per minute (8 1/2" x 11") 15 copies per minute (8 1/2" x 11"R) 12 copies per minute (8 1/2" x 14") 10 copies per minute (11" x 17") 20 pages per minute Max. 99 copies, subtractive counter 7.2 seconds 35 seconds Variable: 50 200% in 1% increments Fixed presets: 50%, 64%, 77%, 95%, 100%, 121%, 129%, 141%, 200% Moving optical source, slit exposure (stationary platen) with automatic exposure function 2 paper trays with auto paper feed (total: 500 sheets); 1 manual feed tray with 100 sheet automatic feed capacity 30 Sheet Single Pass Feeder (SPF) (option)
FINISHING CAPABILITY FUSING SYSTEM DEVELOPER SYSTEM LIGHT SOURCE COPY RESOLUTION GRADATION REQUIRED POWER SUPPLY POWER CONSUMPTION WEIGHT DIMENSIONS OPERATING CONDITIONS OPTIONAL EQUIPMENT
Offset stacking Heat rollers Magnetic brush development Xenon lamp Scan: 400 dpi/ Copy: 600 dpi 256 levels AC 120V, 60 Hz, 11 amps Max. 1.3 kW Approx. 69.9 lbs. 23.3" (w) x 21" (d) x 20.6" (h) Temperature: 59F to 86F (15C to 30C) Humidity: 20% to 85% Single Pass Feeder (AR-SP2) Electronic Sorting Kit (AR-EB3) 250-Sheet Paper Feed Unit (AR-DE5) 500-Sheet Paper Feed Unit (AR-DE6) Facsimile Expansion Kit (AR-FX2) Printer Expansion Kit (AR-PB8) PS2 Expansion Kit (AR-PS1) Network Interface Card (AR-NC3D) LCD Panel Kit (AR-PA1) Job Separator Tray (AR-TR2) Platen Cover (AR-VR1)

PRINT SPEED CONTINUOUS COPY FIRST COPY OUT TIME WARM UP TIME COPY RATIO
EXPOSURE SYSTEM COPY PAPER FEED ORIGINAL FEED SYSTEM
OPTIONAL PRINT KIT SPECIFICATIONS
PRINT KIT RESOLUTION COMPUTER INTERFACE PAGE DESCRIPTION LANGUAGE

DESCRIPTION

OPTIONAL FAX SPECIFICATIONS
SENDING Super G3 Modem (33,600 bps) 3 Second Transmission Speed* 30 Page Auto Document Feeder (AR-SP2 option) 35 Rapid and Group Dial Keys 150 Speed Dial Keys 5 Program Keys Auto Book Fax Broadcasting to 200 Locations

RECEIVING

AR-PB8 AR-PS1 (PostScript Expansion Kit) 1200 dpi equivalent with smoothing technology; 600 dpi; 300 dpi IEEEP 1284 bi-directional parallel port 10/100BaseT with AR-NC3D (option) PCL5e/PCL6 Emulation; PostScript Level 2 Emulation (when optional AR-PS1 is installed) Microsoft Windows 3.1/95/98; Windows NT 4.0, Windows 2000 Macintosh OS 8.5 and above (with AR-PS1 option)
600 Sheet Paper Capacity (expandable to 1,100 sheets) 256 Halftone Levels Out of Paper Reception Automatic Reduction

MEMORY

PRINT DRIVER SUPPORT RESIDENT FONTS
2 MB Standard Memory (expandable to 6MB) Memory Transmit Flash Memory
45 Outlines for PCL6 Emulation; 35 Outlines for PostScript2 Emulation (when optional AR-PS1 is installed) 8MB/136MB 2 DIMM Slots PC DIMM
MEMORY (STD/MAX) MEMORY EXPANSION SLOTS EXPANSION MEMORY
Design and specifications are subject to change without notice.
Sharp is a registered trademark of Sharp Corporation. All trademarks and registered trademarks are the property of their respective holders.
* Based on ITU-T Test Chart #1 at standard resolution excluding time for protocol signals (i.e., ITU-T phase C time only) sent at 33.6 Kbps. Transmission speeds will vary based on line type and conditions.
SHARP ELECTRONICS CORPORATION Document and Network Systems of America Sharp Plaza, Mahwah, NJ 07430-2135 201-529-9600 www.sharp-usa.com

WWW.SHARP-USA.COM

Sharp Electronics Corporation 2000

CPD-3346