!ar_m250_310_5600series_sec_fax.fm 1
TO USERS OF THE AR-M256/AR-M257/AR-M258/AR-M316/ AR-M317/AR-M318/AR-5625/AR-5631/ MX-M260/MX-M310
Thank you for purchasing the facsimile expansion kit. The Operation Manual (for facsimile) primarily explains the fax function on the AR-M230/M270 Series. Although the appearance of the operation panel and touch panel may be slightly different on your model, the procedures for using the fax function are the same. Please refer to this guide along with the Operation Manual (for facsimile) to use the fax function of the machine. Users of the MX-M260 and the MX-M310 should also read "TO USERS OF THE MX-M260/MX-M310" on page 3.
ADDITION OF DESTINATION STORING FUNCTION TO THE WEB PAGE
A feature for storing fax destinations in the Web page has been added. (when the PRINTER EXPANSION KIT is installed)

[Accessing Web pages]

Open the Web browser on your computer.
Supported browsers: Internet Explorer 6.0 or later (Windows) Netscape Navigator 7.0 or later Safari 1.2 or later (Macintosh)
In the "Address" field of your Web browser, enter the IP address of the machine as a URL.
Example: When the connection is established, the Web page will appear in your browser.
Store fax destinations in "Destination" under "Image Send Management" in the Web page menu frame.
!ar_m250_310_5600series_sec_fax.fm 2
ADDITION TO THE KEY OPERATOR PROGRAMS
The following program has been added to the "FAX DEFAULT SETTINGS".
DISABLE OF FAX NUMBER DIRECT ENTRY
When the fax function is enabled, this program is used to prohibit dialing of a destination fax number by direct entry with the numeric keys. To prohibit dialing by direct entry with the numeric keys, touch the checkbox to select it. When this is done, faxes can only be sent to destinations that have been stored, and thus this program can be used to restrict fax destinations and prevent accidental transmission to an incorrect number. The following operations are also prohibited: Storing rapid dial keys Storing relay groups Direct entry of fax numbers when storing a group Direct entry of fax numbers when storing programs Editing and deleting of stored rapid dial keys Editing and deleting of stored relay groups Direct entry of fax numbers when editing stored groups Direct entry of fax numbers when editing stored programs Direct entry of a fax number for received fax forwarding

OTHER CHANGES

If you are using the fax function on the AR-M256/AR-M257/AR-M258/AR-M316/AR-M317/AR-M318/ AR-5625/AR-5631/MX-M260/MX-M310, please make the following substitutions in the Operation Manual (for facsimile). When using the fax function on the AR-M256/AR-M257/AR-M258/AR-M316/ AR-M317/AR-M318/AR-5625/AR-5631/ MX-M260/MX-M310 When using job build mode, the number of originals scanned will appear in the display.

Changes

Text in the Operation Manual (for facsimile) When using job build mode, the number of originals scanned will appear in the display. When the count reaches 256 pages, it will reset to 0 and further scanned pages will be counted from 1.
!ar_m250_310_5600series_sec_fax.fm 3
TO USERS OF THE MX-M260/MX-M310
Users of the MX-M260 and the MX-M310 should also read the explanation below.

OPERATION PANEL

The operation panel of the MX-M260/MX-M310 is different from the panel described in the Operation manual (for facsimile). When reading explanations that use an illustration of the operation panel, refer to the illustration below. For the names and functions of the keys, see "PART NAMES AND FUNCTIONS" in the Operation manual (for facsimile) (page 5). (The numbers in the illustration correspond to the explanations.)

COPY PRINT SCAN FAX

ON LINE DATA DATA LINE DATA

JOB STATUS

SYSTEM SETTINGS

LOGOUT

[SYSTEM SETTINGS] Key
The [SYSTEM SETTINGS] key on the operation panel is called the [CUSTOM SETTINGS] key in the Operation manual (for facsimile). When configuring system settings, refer to the illustration below. At other places in the Operation manual that refer to the "Custom Settings", substitute "System Settings". Location in Operation manual (for facsimile) When using the MX-M260/MX-M310 Applicable function USING THE FAX FORWARD FUNCTION RECEIVING A FAX AFTER TALKING (MANUAL RECEPTION) STORING, EDITING, AND DELETING AUTO DIAL KEYS, PROGRAMS AND RELAY GROUPS
LINE DATA B STATUS CUSTOM SETTINGS

LINE DATA

Operation manual page (chapter) Page 29 Page 62
DATA CUSTOM SETTINGS ACC.#-C

Page 65

STORING A GROUP INDEX PRINTING PROGRAMMED INFORMATION PRINTING REPORT USING THE KEY OPERATOR PROGRAMS
Page 78 Page 79 Page 85 Page 94

B STATUS

!ar_m250_310_5600series_sec_fax.fm 4
ADDITION TO SPECIAL MODES
The following function has been added to the "SPECIAL MODES".
TRANSACTION REPORT PRINT SELECT SETTING
Transaction reports are printed based on conditions set in the system settings; however, you can temporarily select different conditions for a transmission. The print conditions for a transaction report are as follows: "PRINT OUT ALL REPORT":A transaction report is printed no matter whether the transmission succeeds or fails. "NO PRINTED":Do not print a transaction report. When "PRINT OUT ALL REPORT" is selected, you can select whether or not part of the transmitted fax image is included on the transaction report (select "PRINT OUT" or "NO PRINTED"). Note that even when "PRINT OUT" is selected, part of the fax image will not be printed when speaker dialing, direct transmission, polling reception, F-code transmission, or confidential transmission is used.
SYSTEM SETTINGS (Administrator)
The "System Settings (Administrator)" in the system settings are referred to as "Key Operator Programs" in the Operation manual (for facsimile). For explanations of the system settings (administrator) for the fax function, see chapter 8, "KEY OPERATOR PROGRAMS", in the Operation manual (for facsimile). At places in the Operation manual (for facsimile) that refer to the "Key Operator Programs", substitute "System Settings (Administrator)". Due to this change, steps 1 to 3 on pages 94 and 105 are as follows.
Press the [SYSTEM SETTINGS] key.

Touch the [ADMINISTRATOR SETTINGS] key.

CONTRAST ADDRESS CONTROL

RECEIVE MODE

ADMINISTRATOR SETTINGS

Use the numeric keys to enter the five-digit administrator password.
Each time a digit is entered, the dash (-) that indicates the digit will change to an asterisk (*). The factory default setting for the administrator password is 00000. For the steps that follow, see pages 94 and 105 of the Operation manual (for facsimile).

ADMINISTRATOR PASSWORD

PRINTED IN CHINA

2009G KS1 TINSE2035QSZZ

!!install_ar230270.book

SOFTWARE SETUP GUIDE

DIGITAL MULTIFUNCTIONAL SYSTEM
INTRODUCTION Inside cover ABOUT THE SOFTWARE 2 BEFORE INSTALLATION 2 INSTALLING THE SOFTWARE 3 CONNECTING TO A COMPUTER 13 CONFIGURING THE PRINTER DRIVER 14 HOW TO USE THE ONLINE MANUAL 15 TROUBLESHOOTING 16

INTRODUCTION

This manual explains how to install and configure the software that is required for the printer function of the machine. The procedure for viewing the online manual is also explained.
The screen images in this manual are mainly for Windows XP. With other versions of Windows, some screen images may be different from those in this manual. The explanations in this manual are based on the North American version of the software. Versions for other countries and regions may vary slightly from the North American version. Where "AR-XXXX" appears in this manual, please substitute the name of your model for "XXXX". This manual refers to the "SHARP Digital Multifunctional System AR-M256/M257/M316/M317/ 5625/5631 Series Software CD-ROM" simply as "CD-ROM".

SOFTWARE LICENSE

The SOFTWARE LICENSE will appear when you install the software from the CD-ROM. By using all or any portion of the software on the CD-ROM or in the machine, you are agreeing to be bound by the terms of the SOFTWARE LICENSE.
The display screens, messages, and key names shown in the manual may differ from those on the actual machine due to product improvements and modifications.

CONTENTS

ABOUT THE SOFTWARE.... 2 BEFORE INSTALLATION.... 2
HARDWARE AND SOFTWARE REQUIREMENTS.. 2 INSTALLATION ENVIRONMENT AND INSTALLATION PROCEDURE. 2
INSTALLING THE SOFTWARE.... 3
STANDARD INSTALLATION (USB only)... 3 CUSTOM INSTALLATION.... 5 INSTALLING THE PC-FAX DRIVER... 11
CONNECTING TO A COMPUTER... 13
CONNECTING A USB CABLE.... 13 CONNECTING A PARALLEL CABLE... 13
CONFIGURING THE PRINTER DRIVER... 14 HOW TO USE THE ONLINE MANUAL... 15 TROUBLESHOOTING.... 16
!ar_m250_310_5600series_sec_splcsetup.book

ABOUT THE SOFTWARE

The CD-ROM that accompanies the machine contains the following software:
For users of Windows NT 4.0 The CD-ROM does not include software for Windows NT 4.0. Contact your dealer or nearest authorized service representative if you want the software for Windows NT 4.0.

Printer driver

The printer driver enables you to use the printer function of the machine.

PC-Fax driver

The PC-Fax driver lets you easily send faxes from your computer through the machine to another fax machine (when the facsimile expansion kit is installed). * To use the PC-Fax driver, Internet Explorer 4.0 or later must be installed in your computer.

BEFORE INSTALLATION

HARDWARE AND SOFTWARE REQUIREMENTS
Check the following hardware and software requirements before installing the software.
IBM PC/AT or compatible computer equipped with a USB 2.0/1.1*1 or bi-directional parallel interface (IEEE 1284) Operating system Windows 98, Windows Me, Windows NT Workstation 4.0 (Service Pack 5 or later)*2, Windows 2000 Professional*2, Windows XP Professional*2, Windows XP Home Edition*2 Other hardware requirements An environment that allows any of the above operating systems to fully operate Computer type *1 Compatible with Windows 98, Windows Me, Windows 2000 Professional, Windows XP Professional or Windows XP Home Edition preinstalled models equipped with a USB interface as standard. *2 Administrator's rights are required to install the software using the installer.
INSTALLATION ENVIRONMENT AND INSTALLATION PROCEDURE
Follow the appropriate installation procedure for your operating system and type of cable as indicated below. Operating system
Windows 98/Me/2000/XP Windows XP Windows 98/Me/2000 Windows 98/Me/NT 4.0/2000
USB* USB*/Parallel USB* Parallel

Procedure to follow

STANDARD INSTALLATION (USB only) (page 3) Installation in Windows XP (USB/Parallel cable) (page 5) Installation in Windows 98/Me/2000 (USB cable) (page 7) Installation in Windows 98/Me/NT 4.0/2000 (Parallel cable) (page 9)
* If the machine is connected by a USB cable, it is recommended that you use the standard installation.

INSTALLING THE SOFTWARE

If an error message appears, follow the on-screen instructions to solve the problem. After the problem is solved, the installation procedure will continue. Depending on the problem, you may have to click the "Cancel" button to exit the installer. In this case, reinstall the software from the beginning after solving the problem.
STANDARD INSTALLATION (USB only)
The procedure for a standard installation of the software is explained below. If the machine is connected by a USB cable, it is recommended that you use the standard installation.

The standard installation can only be used when the machine is connected by a USB cable. If the machine is connected by a parallel cable, use the custom installation procedure (page 5).
The USB cable must not be connected to the machine. Make sure that the cable is not connected before proceeding. If the cable is connected, a Plug and Play window will appear. If this happens, click the "Cancel" button to close the window and disconnect the cable.
Read the message in the "Welcome" window and then click the "Next" button. Click the "Standard" button. Follow the on-screen instructions.
The cable will be connected in step 9.
Insert the "Software CD-ROM" into your computer's CD-ROM drive. Click the "start" button, click "My Computer" ( ), and then double-click the [CD-ROM] icon ( ). In Windows 98/Me/2000, double-click "My Computer" and then double-click the [CD-ROM] icon.

Caution

Double-click the "Setup" icon (
If you are running Windows 2000/XP and a warning message appears regarding the Windows logo test or digital signature, be sure to click "Continue Anyway" or "Yes".
The "SOFTWARE LICENSE" window will appear. Make sure that you understand the contents of the license agreement, and then click the "Yes" button.
You can show the "SOFTWARE LICENSE" in a different language by selecting the desired language from the language menu. To install the software in the selected language, continue the installation with that language selected.
When the finish screen appears, click the "Close" button. A message will appear instructing you to connect the machine to your computer. Click the "OK" button.
After the installation, a message prompting you to restart your computer may appear. In this case, click the "Yes" button to restart your computer.
Make sure that the power of the machine is turned on, and then connect the USB cable. (page 13) Windows will detect the machine and the Plug and Play screen will appear. Begin installation of the printer driver. "SHARP AR-XXXX" will appear in the "Found New Hardware Wizard" dialog box. Select "Install the software automatically (Recommended)" and click the "Next" button. Follow the on-screen instructions.
This completes the installation of the software. After installation, see "CONFIGURING THE PRINTER DRIVER" (page 14) to check the printer driver settings.

CUSTOM INSTALLATION

The procedure for a custom installation of the software is explained below. Use the custom installation procedure when the machine is connected by a parallel cable, when the machine is used as a shared printer on a network, or when installing the PC-Fax driver.
Installation in Windows XP (USB/Parallel cable)
The USB or parallel cable must not be connected to the machine. Make sure that the cable is not connected before proceeding. If the cable is connected, a Plug and Play window will appear. If this happens, click the "Cancel" button to close the window and disconnect the cable.
Click the "Custom" button.
The cable will be connected in step 15.
Insert the "Software CD-ROM" into your computer's CD-ROM drive. Click the "start" button, click "My Computer" ( ), and then double-click the [CD-ROM] icon ( ). Double-click the "Setup" icon ( ).
Click the "Printer Driver" button. Before installing the software, be sure to click the [Display Readme] button and view the detailed information on the software.
Read the message in the "Welcome" window and then click the "Next" button.
Click the "Next" button.
When you are asked how the printer is connected, select "Connected to this computer" and click the "Next" button.
Click the "Close" button. A message will appear instructing you to connect the machine to your computer. Click the "OK" button.
A confirmation window appears. Check the contents and then click the "Next" button. Click the "Next" button. Begin installation of the printer driver.
Connect the interface cable to the machine and your computer (page 13). If you are using a USB cable, make sure the machine's power is turned on and then connect the cable. If you are using a parallel cable, turn off the power of the machine and your computer, connect the cable, turn on the power of the machine, and then turn on your computer. Windows will detect the machine and the Plug and Play screen will appear.
If the following screen appears while the files are being copied (the message may appear more than once), click the "Continue Anyway" button.
Begin installation of the printer driver. "SHARP AR-XXXX" will appear in the "Found New Hardware Wizard" dialog box. Select "Install the software automatically (Recommended)" and click the "Next" button. Follow the on-screen instructions.
If a warning window appears regarding the "Windows logo test", be sure to click the "Continue Anyway" button.

When "The installation of the SHARP software is complete" appears, click the "OK" button.
Installation in Windows 98/Me/2000 (USB cable)
The cable will be connected in step 16.
Insert the "Software CD-ROM" into your computer's CD-ROM drive. Double-click "My Computer" ( ), and then double-click the [CD-ROM] icon ( ). Double-click the "Setup" icon ( ).
When "The installation of the SHARP software is complete" appears, click the "OK" button. Click the "Close" button. A message will appear instructing you to connect the machine to your computer. Click the "OK" button.
When the interface selection screen appears, select "USB" and click the "Next" button.
Make sure that the power of the machine is turned on, and then connect the USB cable. (page 13) Windows will detect the machine and the Plug and Play screen will appear. Follow the instructions in the Plug and Play screen that appears in your version of Windows to begin the installation.
A confirmation window appears. Check the contents and then click the "Next" button. Click the "Next" button. In Windows 98/Me, click the "Yes" button. Begin installation of the printer driver.
In Windows 2000, if the following screen appears while the files are being copied (the message may appear more than once), click the "Yes" button.
Installation in Windows 98/Me/NT 4.0/2000 (Parallel cable)
The parallel cable must not be connected to the machine. Make sure that the cable is not connected before proceeding. If the cable is connected, a Plug and Play window will appear. If this happens, click the "Cancel" button to close the window and disconnect the cable.
The cable will be connected in step 17.
Click the "Next" button. If you are using Windows NT 4.0, go to step 12.

!02_InstallGuide-body.fm

If "LPT1" does not appear, another printer or peripheral device is using LPT1. In this case continue the installation, and after the installation is finished, change the port setting so that the machine can use LPT1. This procedure is explained in "Another printer is using the parallel port (when using a parallel cable)" on page 16.
When the interface selection screen appears, select "Parallel" and click the "Next" button.
When the model selection window appears, select model name of your machine and click the "Next" button. Click the "Next" button. In Windows 98/Me/NT 4.0, click the "Yes" button. Begin installation of the printer driver.

Select the printer port and click the "Next" button. Select "LPT1" for the printer port.
Turn off the power of the machine and your computer, and connect the machine to your computer with the parallel cable. (page 13) After connecting the machine to your computer, turn on the power of the machine and then start up your computer.
INSTALLING THE PC-FAX DRIVER
To use the PC-Fax driver, Internet Explorer 4.0 or later must be installed on your computer. If the PC-Fax function will be used over a USB connection, install the printer driver before installing the PC-Fax driver. The PC-Fax driver can only be used if the facsimile expansion kit is installed.
The USB or parallel cable must not be connected to the machine. Make sure that the cable is not connected before proceeding. If the cable is connected, a Plug and Play window will appear. If this happens, click the "Cancel" button to close the window and disconnect the cable. Insert the "Software CD-ROM" into your computer's CD-ROM drive. Click the "start" button, click "My Computer" ( ), and then double-click the [CD-ROM] icon ( ). In Windows 98/Me/2000, double-click "My Computer" and then double-click the [CD-ROM] icon. Double-click the "Setup" icon ( ).
Click the "PC-Fax Driver" button. Before installing the software, be sure to click the [Display Readme] button and view the detailed information on the software.
Read the message in the "Welcome" window and then click the "Next" button. Click the "Custom" button.
When the port selection window appears, select the port that the printer driver is using (USB001, etc.) and click the "Next" button.
Click the "Close" button.
This completes the installation of the software.
The port used by the printer driver is indicated by a checkmark in the "Ports" tab of the printer driver properties window. (In Windows 98/Me, the port is selected in "Print to the following port" in the "Details" tab.) The USB port name will vary depending on the number of USB ports created on your computer. If the port created during installation of the printer driver is your first USB port, the name will be "USB001".

When the model selection window appears, select model name of your machine and click the "Next" button. Select whether or not you wish the PC-Fax driver to be your default printer and click the "Next" button. When the printer name window appears, click the "Next" button. If you wish to change the printer name, enter the desired name. Click the "Next" button.
When the installation completed screen appears, click the "OK" button.

CONNECTING TO A COMPUTER

Follow the procedure below to connect the machine to your computer. Interface cables for connecting the machine to your computer are not included with the machine. Please purchase the appropriate cable for your computer.

Interface cable

USB cable
Shielded twisted pair cable, high-speed transmission equivalent (9 feet (3 m) max.) If the machine will be connected using a USB 2.0 interface, please purchase a USB cable that supports USB 2.0.

Parallel cable

IEEE 1284-Shielded type bi-directional parallel interface cable (9 feet (3 m) max.)
USB is available on a PC/AT compatible computer that was originally equipped with USB and had Windows 98, Windows Me, Windows 2000 Professional, Windows XP Professional or Windows XP Home Edition preinstalled. Do not connect the interface cable before installing the printer driver. The interface cable must be connected during installation of the printer driver.

CONNECTING A USB CABLE

Insert the cable into the USB connector on the machine.
Insert the other end of the cable into your computer's USB connector.
The cable can also be inserted into a USB 1.1 connector.
CONNECTING A PARALLEL CABLE
Ensure that your computer and the machine are turned off. Insert the cable into the parallel connector on the machine and fasten with the clasps.
Insert the other end of the cable into your computer's parallel connector.
CONFIGURING THE PRINTER DRIVER
After installing the printer driver, you must configure the printer driver settings appropriately for the number of paper trays on the machine and the size of paper loaded in each tray.
Click the "start" button, click "Control Panel", click "Printers and Other Hardware", and then click "Printers and Faxes". In operating systems other than Windows XP, click the "Start" button, select "Settings", and then click "Printers". Click the "SHARP AR-XXXX" printer driver icon and select "Properties" from the "File" menu. If you are using Windows NT 4.0/2000/XP, go to step 4. In Windows 98/Me, click the "Setup" tab. Click the "Configuration" tab and set the printer configuration based on the options that have been installed. Set the printer configuration properly. Otherwise, printing may not take place correctly.

Click the "Set Tray Status" button and select the size of paper that is loaded in each tray. Select a tray in the "Paper source" menu, and select the size of paper loaded in that tray from the "Set Paper Size" menu. Repeat for each tray.
Click the "OK" button in the "Set Tray Status" window. Click the "OK" button in the printer properties window.
HOW TO USE THE ONLINE MANUAL
The online manual provides detailed instructions for operating the machine as a printer. View the online manual when you use the printer function after the initial setup is completed.
Contents of the online manual
The contents of the online manual are as follows. How to use the online manual: Explains how to use the online manual. Print: Provides information on how to print a document. Printer sharing: Explains how to configure the machine for use as a shared printer. Troubleshooting: Provides instructions on how to solve driver or software problems.
To view the manuals in PDF format, Acrobat Reader or Adobe ReaderTM of Adobe Systems Incorporated is required. If neither program is installed on your computer, the programs can be downloaded from the following URL: http://www.adobe.com/
Insert the "Software CD-ROM" into your computer's CD-ROM drive. Click the "start" button, click "My Computer" ( ), and then double-click the [CD-ROM] icon ( ). In Windows 98/Me/NT 4.0/2000, double-click "My Computer" and then double-click the [CD-ROM] icon. Double-click the "Manual" folder, double-click the "EnglishA" folder (for regions other than the U.S., double-click the "English" folder), and then double-click the "AR_M316.pdf" icon. The online manual will appear.

TROUBLESHOOTING

If the software does not install correctly, check the following items on your computer. To remove the software, see "Uninstalling the printer driver" in the online manual. Troubleshooting information can also be found in the README files for each of the software programs. To view a README file, click the "Display Readme" button in the "Software Selection" screen.

Printer driver cannot be installed (Windows 2000/XP)
If the printer driver cannot be installed in Windows 2000/XP, follow these steps to check your computer's settings.
Another printer is using the parallel port (when using a parallel cable)
If another printer is using the parallel port and printing is not possible using the machine, follow the steps below to change the port setting of the other printer driver, and make sure that the port of the printer driver for the machine is set to LPT1.
Click the "start" button and then click "Control Panel". In Windows 2000, click the "Start" button, select "Settings", and then click "Control Panel". Click "Performance and Maintenance", and then click "System". In Windows 2000, double-click the "System" icon. Click the "Hardware" tab and then click the "Driver Signing" button. Check "What action do you want Windows to take?" ("File signature verification" in Windows 2000).
Click the "start" button, click "Control Panel", click "Printers and Other Hardware", and then click "Printers and Faxes". In Windows 98/Me/NT 4.0/2000, click the "Start" button, select "Settings", and then click "Printers". Click the icon of the printer driver for which you wish to change the port setting, and select "Properties" from the "File" menu. Click the "Ports" tab. In Windows 98/Me, click the "Details" tab. Select "FILE:" in the "Print to the following port" list box, and click the "OK" button. Click the "SHARP AR-XXXX" printer driver icon and select "Properties" from the "File" menu. Click the "Ports" tab. In Windows 98/Me, click the "Details" tab. Select "LPT1" in the "Print to the following port" list box, and click the "OK" button.
If the option "Block" has been selected, it will not be possible to install the printer driver. Select the option "Warn" and then install the printer driver as explained in "INSTALLING THE SOFTWARE".

In the event that you need to use the other printer, repeat the above steps to set the port of the machine to "FILE:", and change the port setting of the other printer back to "LPT1".
The printer driver cannot be correctly installed by Plug and Play (Windows 2000/XP)
In Windows 2000/XP, if the printer driver cannot be correctly installed by Plug and Play (for example, Plug and Play takes place without copying the required files for the printer driver installation), follow these steps to remove unneeded devices and then install the printer driver as explained in "INSTALLING THE SOFTWARE".
Plug and play screen does not appear (when using a USB cable)
If the Plug and Play screen does not appear after you connect the machine to your computer with a USB cable and turn on the machine, follow the steps below to verify that the USB port is available.
Click the "start" button, click "Control Panel", and then click "Performance and Maintenance". In Windows 2000, click the "Start" button, select "Settings", and then click "Control Panel". Click "System", click the "Hardware" tab, and click the "Device Manager" button.
Click the "start" button, click "Control Panel", and then click "Performance and Maintenance". In Windows 98/Me/2000, click the "Start" button, select "Settings", and then click "Control Panel". Click "System", click the "Hardware" tab, and click the "Device Manager" button. "Universal Serial Bus controllers" will appear in the list of devices.
In Windows 2000, double-click the "System" icon, click the "Hardware" tab, and click the "Device Manager" button.

Click the devices".

icon beside "Other
In Windows 98/Me, double-click the "System" icon and click the "Device Manager" tab. In Windows 2000, double-click the "System" icon, click the "Hardware" tab, and click the "Device Manager" button. If the "System" icon does not appear in Windows Me, click "view all Control Panel options".

If "SHARP AR-XXXX" appears, select and delete it.
Click the icon beside "Universal Serial Bus controllers".
If "Other devices" does not appear, close the "Device Manager" window.
Install the software as explained in "INSTALLING THE SOFTWARE".
Two items should appear: your controller chipset type and Root Hub. If these items appear, you can use the USB port. If the "Universal Serial Bus controllers" shows a yellow exclamation point or does not appear, you must check your computer manual for USB troubleshooting or contact your computer manufacturer.
Once you have verified that the USB port is enabled, install the software as explained in "INSTALLING THE SOFTWARE".
AR-M256/AR-M257/AR-M316/AR-M317/AR-5625/AR-5631 SOFTWARE SETUP GUIDE
This manual has been printed using a vegetable-based soy oil ink to help protect the environment. Printed on 100% post-consumer recycled paper

PRINTED IN CHINA

2007C KS2 TINSE1680QSZZ