AUTOMATIC DOCUMENT FEEDER
Originals set in the automatic document feeder will be automatically fed and copied sequentially. The automatic document feeder will simultaneously scan both sides of originals when two-sided to one-sided or twosided to two-sided copying is being done.

Acceptable originals

A stack of up to 50 original sheets (30 original sheets*1 for 8-1/2" x 14" (B4) or larger) of the same size paper can be set in the document feeder tray provided the stack height is within the limit shown below. A stack of up to 30 mixed size originals can be set if the width of the originals is the same and the stack height is within the limit shown below. In this case, however, stapling and duplex will not function and some special functions may not give the expected result. *1 For paper heavier than 28 lbs. (105 g/m2), only a stack of up to 15 sheets can be set. Setting 16 or more sheets may cause incorrect scanning of original and scanned image may become expanded compared with original itself.
s Size and weight of acceptable originals
5-1/2" x 8-1/2" or A5
s Total amount of originals that can be set in the document feeder tray
Total aggregate thickness must not exceed 1/4" or 6.5 mm (for 14 to 21 lbs. or 50 to 80 g/m2 paper). 1/4" or 6.5 mm or less Total aggregate thickness must not exceed 3/16" or 5.0 mm (for 21 to 34 lbs. or 80 to 128 g/m2 paper). 3/16" or 5.0 mm or less

Original size:

11" x 17" or A3 (297 x 420 mm)
(148 x 210 mm) Weight (thickness):

14 lbs. or 50g/m 2

34 lbs. or 128g/m 2
g/m 2. Weight of a sheet of paper of 1 m 2
Notes on use of the automatic document feeder

q q q q

Use originals within the specified size and weight ranges. Use of originals out of the specified range may cause an original misfeed. Before loading originals into the document feeder tray, be sure to remove any staples or paper clips. If originals have damp spots from correction fluid, ink or glue from pasteups, be sure they are dried before they are fed. If not, the interior of the document feeder or the document glass may be soiled. To prevent incorrect original size detection, original misfeeds or smudges on copies, use the following as a guide for feeding originals. Transparency film, tracing paper, carbon paper, thermal paper or originals printed with thermal transfer ink ribbon should not be fed through the document feeder. Originals to be fed through the feeder should not be damaged, crumpled or folded or have loosely pasted paper on them or cutouts in them. Originals with multiple punched holes other than two-hole or three-hole punched paper may not feed correctly. When using originals with two or three holes, place them so that the punched edge is at a position other than the feed slot.

Hole positions

Hole positions Hole positions

SETTING ORIGINALS

s When using the automatic document feeder s When using the document glass
Open the document cover, place an original face down on the document glass, and then gently close the document cover.
1 Ensure that there is no original on the document glass.

Original size detector

2 Adjust the original guides to the size of the originals.
NOTE Do not place any objects under the original size detector, because they may damage it or the original size may not be detected properly.

Original scale mark

3 Place the originals face down in the document feeder tray.
Set the originals all the way into the feed slot. Do not exceed the maximum height line marked on the original guide.
51/2 x 81/2 or A5 81/2 x 11 or A4
81/2 x 14 or B4 11x17 or A3

81/2 x 11R or A4R

Set an original by aligning its corner with the tip of the scale ( ) mark at the left rear corner of the glass as shown in the illustrations.
s Standard original setting orientation
Descriptions of functions that follow in this manual assume that originals are oriented as shown. Document feeder tray

Document glass

Place originals in the document feeder tray or on the document glass so that the top of the original is positioned to the rear side of the machine. If not, staples will be incorrectly positioned and some special features may not give the expected result.

Bottom

Bottom Bottom
s Automatic copy image rotation - rotation copying
If the orientation of the originals and copy paper are different, the original image will be automatically rotated 90 and copied. (When an image is rotated, a message will be displayed.) When enlargement of originals larger than 81/2" x 11" or A4 is selected, rotation cannot be done. [Example]
Orientation of original Orientation of paper Copy after rotation

Face down

q This
function operates in the auto paper select or auto image mode. (Rotation copying can be disabled with a key operator program. See page 33.)

NORMAL COPYING

This section describes the normal copying procedure.
Copying from the automatic document feeder
s 1-sided copies of 1-sided originals

Original Copy

the 1 Place 7) originals in the document feeder tray. (page

5 Touch the [OK] key. 0

2 Ensure that the 1-sided to 1-sided copy mode is selected.

ORIGINAL A4 A4

6 Ensure that paper of the same size as the originals is automatically selected. (UNote)
The selected tray will be highlighted or the message LOAD xxxxxx PAPER. will appear. If the message appears, load paper in a paper tray or the bypass tray with paper of the required size. Even if the message above is displayed, copying can be performed onto the currently selected paper. (UNote) The following requirements must be satisfied. q Originals of a standard size (11" x 17", 8-1/2" x 14", 8-1/2" x 11", 8-1/2" x 11"R, 5-1/2" x 8-1/2", A3, B4, A4, A4R or A5) are set and the auto paper select function is enabled. If originals of a size other than the sizes above are to PLAIN A4 be copied, manually select the desired paper size. 1
The one-sided to onesided mode is selected when no icon for a twosided mode appears in the dashed area on the display. If the 1-sided to 1-sided copy mode is already selected, steps 3 to 5 are not needed.

AUTO A4 PAPER SELECT

3 Touch the [2-SIDED COPY] key.

2-SIDED COPY OUTPUT

Touch the [1-sided to 1-sided copy] key.
The [1-sided to 1-sided] key will be highlighted.

2. A4X

TRANSPA PLAIN
7 Select the desired output mode (see below).
The sort mode is the default mode. To select the group mode, touch the [OUTPUT] key, then touch the [GROUP] key on the output setting screen, and then touch the [OK] key on the setting screen.
8 Use the numeric keys to set the desired number of copies.
Up to 999 can be set. Use the [C] (clear) key to cancel an entry if a mistake has been made.

9 Press the [START] key.

If the [C] key is pressed while originals are being scanned, scanning will stop. If copying had already started, copying and scanning will stop after the original in progress is output to the original exit area. In these cases the copy quantity will be reset to 0. If scanning has been completed but copying is still in progress, copying will continue. NOTE The 1-sided to 1-sided copying mode is set as the default in the initial settings. This setting can be changed by a key operator program (initial status setting ).
Output modes (sort mode and group mode)
[Example] Five sets of copies from three originals q Sort copy When originals are placed in the document feeder tray, a sort icon will appear on the touch panel and the sort copy mode will be automatically selected. In this case, copies will be delivered as shown in the upper illustration to the left. For output in the group mode as shown in the lower left illustration, the group mode must be selected on the output setting screen.

Originals

NOTE Exposure mode selection TEXT: This mode is useful for producing dark text copies with minimum background. TEXT/PHOTO: This provides the best balance for copying an original which contains both text and photos. This mode is also useful for copying printed photographs. PHOTO: This mode provides the best copies of photographs with fine details.
NOTE Exposure levels in the text mode 1 to 2: Dark originals such as newspaper 3: Normal density originals 4 to 5: Originals written with pencils or light color characters
After adjusting the exposure, follow any of the copying procedures.
To return to the automatic exposure mode, touch the [EXPOSURE] key and select [AUTO]. The automatic exposure level can be adjusted using a key operator program. (page 33)
REDUCTION/ENLARGEMENT/ZOOM
Reduction and enlargement ratios can be selected either automatically or manually as described in this section.
Automatic selection will enlarge or reduce images based upon the original size and copy paper size to give the best possible fit of the image to the copy paper. q Manual selections can be made in the range of 25% to 400%. There are three preset reduction ratios (25%, 64% and 77%) and three preset enlargement ratios (121%, 129% and 400%) available for the inch system. There are four preset reduction ratios (25%, 70%, 81%, 86%) and four preset enlargement ratios (115%, 122%, 141%, 400%) available for the AB system.
Automatic selection (auto image)
The reduction or enlargement ratio will be selected automatically based on the original size and the selected pape size the original in the document 1 Placethe document glass. (page 7) feeder tray or on
The detected original size will be displayed. Automatic selection can be used only for 11" x 17", 81/2" x 14", 8-1/2" x 11", 8-1/2" x 11"R, 5-1/2" x 8-1/2" size originals and copy paper in the inch system and A3, B4, A4, A4R or A5 in the AB system.
such 4 Make all other desired settingspressas exposure or the number of copies, and the [START] key.
When copying from the document glass in the sort mode, touch the [READEND] key after all originals have been scanned. (step 7 on page 13)
SELECT] 2 Touch the [PAPERsize. key and then select the desired paper

1. A4 2. A4X

PLAIN TRANSPA PLAIN
When the desired paper size key is touched, the paper size will be highlighted and the paper size setting window will be closed. If paper of the desired size is not loaded in any tray, load paper of the required size in a paper tray and enter the paper size.
To cancel the auto image mode, touch the [AUTO IMAGE] key again to clear the highlighted display.

CANCEL SIDE 1

MARGIN SHIFT

SIDE 2

(0 20)

PAMPHLET COPY

2 Select the shift direction.

RIGHT LEFT

Touch a shift direction key to select right or left. The selected key will be highlighted.
Use the key and the keys to set the shift amount. The shift amount can be set from 0" to 1" in 1/8" increments ( 0 mm to 20 mm in 1 mm increments for the AB system). If a duplex module is not installed, the shift amount setting for the reverse side is not displayed.
Touch the [OK] key on the special 4 After adjusting the exposure, followmodes screen. any of the copying procedures.
To cancel the margin shift function, touch the [CANCEL] key on the margin shift setting screen.
The erase function is used to erase the shadow lines on copies produced when copying thick originals or books. The erase modes that can be selected are shown below. The erase width is approximately 1/2" (10 mm) in its initial setting.
Edge erase Eliminates shadow lines around the edges of copies caused when thick paper or a book is used as an original.
Center erase Eliminates shadow lines produced by the bindings of bound documents.
Edge + center erase Eliminates shadow lines around the edges of copies and eliminates the shadow at the center of copies.
1 Touch the [ERASE] key on the SPECIAL MODES screen.
The erase setting screen will appear.

ERASE JOB BUILD

2 Select the desired erase mode.
ERASE EDGE ERASE CENTER ERASE EDGE+CENTER ERASE
Select one of the three erase modes. The selected key will be highlighted.
3 Adjust the amount of erase and touch the [OK] key.

CANCEL EDGE OK

Use the and keys to adjust the erase width and then touch the [OK] key.
To cancel the erase function, touch the [CANCEL] key on the erase setting screen.

Dual page copy

The dual page copy function produces separate copies of two documents placed side by side on the document glass. It is especially useful when copying books and other bound documents. [Example] Copying right and left pages of a book
Book original Dual page copy
The dual page copy function can be used with reduction copying but cannot be used with enlargement copying. The dual page copy function can be done only from the document glass. The automatic document feeder cannot be used with this function. Only 8-1/2" x 11" or A4 paper can be used.

When copying book originals:

81/2 x 11

This page is copied first.

Center line of original

When copying a thick book, press down lightly on the document cover.
PAGE 1 Touch the [DUALscreen. COPY] key on the SPECIAL MODES
The [DUAL PAGE COPY] key will be highlighted.
4 Ensure that 8-1/2" x 11" or A4 size paper is selected.
AUTO A4 PAPER SELECT 100% OPY RATIO
If 8-1/2" x 11" or A4 size paper is not selected, touch the [PAPER SELECT] key to select 8-1/2" x 11" or A4 size paper.
DUAL PAGE COPY MULTI SHOT
2 Touch the [OK] key on the special modes screen.

OK DUAL PAGE COPY

After adjusting the exposure, follow any of the copying procedures. When copying onto two sides of paper, follow steps 2 to 4 on page 14 and then follow steps 4 to 7 on page 13. When copying onto one side of paper, follow steps 4 to 7 on page 13.
To cancel the dual page copy function, touch the [DUAL PAGE COPY] key on the special modes screen (step 1). (The highlighted display will be canceled.)
3 Place the originals on the document glass.
NOTE To erase shadows caused by document binding, use the edge erase function (page 21).

Pamphlet copy

The pamphlet copy function is used to arrange copies in proper order for eventual center-stapling and folding into a booklet. Two original pages are copied onto each side of copy paper. Four pages are, therefore, copied onto one sheet. [Example] Copying eight originals in the pamphlet copy mode
Originals (one-sided) Finished copies are folded in two. Left binding For left to right turning

First page

Originals (two-sided)
Right binding For right to left turning
Scan the originals from the first page to the last page. The order of copying will be automatically adjusted by the machine. Either left binding (right to left turning) or right binding (left to right turning) can be selected. Four originals will be copied onto one sheet. Blank pages may be automatically produced at the end depending on the number of the originals. When using this function, a duplex module must be installed. If a saddle stitch finisher is installed, copies can be stapled in two positions along the center of copies and folded at the center.
1 Touch the [PAMPHLET COPY] key on the SPECIAL MODES screen.
The pamphlet copy setting screen will appear.
size has 6 Ensure that the desired paperthe originalbeen automatically selected based on size.
AUTO A3 PAPER SELECT 100% OPY RATIO
2 Designate the type of originals to be copied: 1sided or 2-sided.

ORIGINAL 1-SIDED 2-SIDED

To select another size paper, select the desired size and touch the [AUTO IMAGE] key. The appropriate copy ratio will be selected automatically based on the original size and the paper size. (See steps 2 and 3 on page 16.)

such 7 Make all other desired settingspress as exposure or the number of copies, and the [START]
8 [When using the automatic document feeder:] Copying will start after all originals have been scanned.
(The next step is not needed.)
[When using the document glass:]
Select the binding position (left binding or right binding) and touch the [OK] key.
Replace the original with the next original and press the [START] key. Repeat this operation until all originals have been scanned.

CANCEL LEFT BINDING

OK RIGHT BINDING
the [READ-END] key. (only if the document 9 Touchis used) glass
PLACE NEXT ORIGINAL. PRESS [START]. WHEN FINISHED, PRESS [READ-END].
4 the first page to 5 Copy fromdocument feederthe last page from either the or the document
Touch the [OK] key on the special modes screen. glass.

READ-END

When the pamphlet copy function is set, the twosided copying mode will be automatically selected and cannot be changed.
To cancel the pamphlet copy function, touch the [CANCEL] key on the pamphlet copy setting screen.

Job build

The number of originals that can be copied into a set of copies in a single run is limited by the capacity of the memory available*1 for scanned originals. Normally the number of originals is further limited by the number of originals that can be set into the document feeder tray*2. The job build function allows scanning and copying of up to 100 originals. For scanning more than 50 originals, the originals must be separated into sections not exceeding 50 originals, scanned in sections and stored in memory. After all sections are in memory, they can be copied as a continuous set. *1 The number of originals that can be copied into a set of copies in a single run is limited by the capacity of the memory available for scanned originals. *2 Up to 50 sheets (30 sheets for 8-1/2" x 14" or larger) can be set into the document feeder tray at one time. [Example] Copying 100 pages of 8-1/2" x 11" or A4 originals

Page sheets

V Divide the originals in sections of 50 sheets and scan the originals starting from the first page of section A and then scan section B. Be sure to keep the correct page order when setting section B.
1 Touch the [JOB BUILD] key on the SPECIAL MODES screen.
The [JOB BUILD] key will be highlighted.
such 4 Make allofother desired settings[START]as the number copies, and press the key.
Scanning of originals will start. After scanning of the first section of originals (A in the example above) is completed, remove the scanned originals, place the next section of originals (section B in the example) and press the [START] key. Repeat this operation until all blocks of originals have been scanned.

JOB BUILD

the 2 TouchJOB[OK] keyison the special modes screen while BUILD highlighted.

OK ERASE JOB BUILD DUAL PAGE COPY MULTI SHOT
5 Touch the [READ-END] key after the last section of originals has been scanned.
3 Place the first section originals in the document feeder tray. (page 7)
To cancel the job build function, touch the [JOB BUILD] key on the special modes screen as in step 1. The highlighted display will be canceled.

Multi shot

The multi shot function is used to copy up to four originals, collectively in a specified order, per sheet of copy paper in any one of four layout patterns. [Example] Copying seven originals using the 4 in 1 MULTI SHOT selection in a layout pattern starting from the upper left to lower right.
One-sided copies from one-sided originals
When using the multi shot function, place the originals, select the desired paper size, and select the copying mode (page 9) before selecting the multi shot function on the special modes screen. When using the multi shot function, the appropriate copy ratio will be automatically set based on the original size, paper size, and the number of originals to be copied onto one sheet. The minimum reduction ratio is 25%. Depending on the original size, paper size, and the number of originals to be copied onto one sheet, the appropriate copy ratio may be smaller than 25%. In this case, portions of original images may not be copied.

Copies

One-sided copies from two-sided originals
1 Touch the [MULTI SHOT] key on the SPECIAL MODES screen.
The multi shot setting screen will appear.
4 [When using the automatic document feeder:] Copying will start after all originals have been scanned.

MULTI SHOT

5 If scanning is being done from the document glass, touch the [READ-END] key after the last
be onto 2 Select the number of originals tothe copied shot one sheet of copy paper on multi selection screen. original has been scanned to start copying.
The orientation of copy paper and the image of the originals may be rotated as needed.

Select the layout.

To cancel the multi shot function, touch the [CANCEL] key on the multi shot setting screen. Select the order in which the originals will be arranged on the copy.

Copying will start with the settings of the recalled job program.
Deleting a stored job program
steps Followpreviousand 2 in Storing a job program on the page.
3 Touch the [DELETE] key.
A JOB PROGRAM HAS BEEN ALREADY STORED. STORE ANOTHER PROGRAM? CANCEL REC LL DELETE STORE STORE/DELETE
Select a storage register number of the program to be deleted.
If a number key for which no job program has been stored is selected, the screen will change to the screen of step 4 on the previous page (for storing a program). The message TO STORE, SELECT AND PRESS [OK]. TO DELETE, PRESS [CANCEL]. will appear. When [CANCEL] is pressed, the screen will return to the selection screen shown to the left.
When the [DELETE] key is touched, the screen in step 2 will return and the program will be deleted. If the [CANCEL] key is touched, the screen in step 2 will return but the program will not be deleted. If no other programs are to be deleted, touch the [EXIT] key on the screen displayed in step 2 to exit the job program mode.
INTERRUPTING A PRINT OR COPY RUN
INTERRUPT can be used to temporarily stop a long print or copy job so that another copy job can be run. Only copy jobs can be run during interrupt.
2 Touch the [INTERRUPT] key.
INTERRUPT ORIGINAL A4 AUTO EXPOSURE AUTO A4 PAPER SELECT 100% CANCEL ORIGINAL A4 AUTO EXPOSURE TO A4 PER SELECT 100%
When it is possible to interrupt a print or copy job in progress, the [INTERRUPT] key will appear as shown in the illustration.
When the [INTERRUPT] key is touched in step 2, the [INTERRUPT] touch key will be replaced by the [CANCEL] key as shown in the illustration. To cancel interrupt copying at any time, touch the [CANCEL] key.
exposure, 3 Make all other desired settings such asthen press paper size and number of copies and the [START] key.
When using the document glass, replace the original with the next original and press the [START] key. Repeat this operation until all originals have been scanned. Then, touch the [READ-END] key.
s When step 3 is completed, a copy job icon will appear at the top of the job icon queue at the left side of the screen and interrupt copying will start. After the interrupt job is completed, the interrupted job will automatically resume.

MISFEED REMOVAL

Misfeed in scanner module
When an original has misfed in the scanner module, remove the misfed original following the procedure below.
NOTES q For misfeed removal in the main unit and other peripheral devices, see the Operation manual (for printer operation and general information). q If you press the [INFORMATION] key, detailed information for misfeed removal will be displayed on the touch panel.

1 Open the document feeding area cover and remove any misfed originals.
Document feeding area cover
s A message may appear indicating the number of originals which must be returned to the document feeder tray. Return the originals to the document feeder tray and press the [START] key.
2 Close the document feeding area cover.
Close the cover securely so that cover clicks into place.
document turn 3 Open theknob in the cover andof thethe green rotating direction arrow to remove any misfed originals.
4 Close the document cover.

TROUBLESHOOTING

Whenever the machine stops or operation is not possible, check the operation panel display for messages. In most cases, these messages will give sufficient information to return the machine to an operating condition. In cases where this information is not enough, check the list below for more information. This section describes problems concerning copier features. For troubleshooting specific problems related to printer, facsimile, or network scanner features, see the separate manuals provided for them. For problems related to other peripheral devices, see chapter 5 of the Operation manual (for printer operation and general information). Problem Machine does not operate. Copies are too dark or too light. Check the START key indicator off? Solution or cause If the indicator is not on, the machine may be warming up. Warm-up should be completed in approximately 80 seconds. Adjust the exposure in the manual mode. (See page 15.) The exposure level in the AUTO mode can be adjusted using a key operator program. Contact your key operator. (See page 33.) Cancel the PHOTO exposure mode. (See page 15.) Clean regularly. (See page 4-12 of the Operation manual (for printer operation and general information).) Clean the original scanning window. (See page 4-12 of the Operation manual (for printer operation and general information).) Use a clean original. Rotation copy functions only if the machine is either in the auto paper select mode or in the auto image mode. (See pages 8 and 16.) Set the original properly. (page 7) Use the auto image function to select the appropriate copy ratio based on the original and copy sizes. (See page 16.) Place the original face down in the document feeder tray or on the document glass. (See page 7.) When using the document glass, set the originals from the first page one sheet at a time. When using the automatic document feeder, set the originals with the first page down. Press the [CA] (clear all) key to cancel the current job. If the data amount exceeds the limit when using the pamphlet copy or multi shot copy which requires scanning of all originals, scanning will be canceled and copying will not be performed. If you install a hard disk drive, the storage capacity will increase.

the original image too dark or too light? q Is the exposure mode set to AUTO?
q Is the exposure mode set to PHOTO?
Smudges appear on copies.

q Document

glass or document transport area dirty? stripes on copies when the document feeder is used?

q Black

q Original smudged or blotchy?
Image cannot be rotated. Par t of original image is not copied. Blank copies Order of copies incorrect
the auto paper select or auto image function set?
q Is the original positioned correctly? q Is the copy ratio proper for the original

and paper sizes?

q Is the original placed face down? q Is the order of originals correct?
Job cancelation needed Scanning of originals is incomplete.
q Is a message requesting cancelation q Is
of job displayed? a message indicating memory is full displayed?

SPECIFICATIONS

Copier
Resolution Gradation Originals Copy sizes Scan: 600 dpi or 300 dpi, output: 600 dpi Scan: 256 levels, output: 2 levels Sheets, bound documents Maximum size: 11" x 17" or A3 Max. 11" x 17" or A3, min. 5-1/2" x 8-1/2" or A5 Image loss: Max 21/64" or 8 mm (leading edge and trailing edge in total), max. 21/ 64" or 8 mm (along all other edges in total) Approx. 80 seconds 35 copy/min. type: 5.3 seconds 45 copy/min. type: 4.6 seconds * Paper is fed from paper tray 1, quick scan from document glass (page 33) is set, the original scanning resolution on the document glass is set to 600 x 300 dpi and no optional hard disk drive is installed. Variable: 25 to 400% in 1% increments, total 376 steps Fixed presets: 25%, 64%, 77%, 100%, 121%, 129%, and 400% for inch system, 25%, 70%, 81%, 86%, 100%, 115%, 122%, 141%, and 400% for AB system 999 copies; subtractive counter
Warm-up time First-copy time*

Copy ratio

Continuous copy
Copying speed 11" x 17" or A3 8-1/2" x 14" or B4 8-1/2" x 11" or A4 8-1/2" x 11"R or A4R
35 copy/min. type 17 copies/min. 20 copies/min. 35 copies/min. 25 copies/min.
45 copy/min. type 20 copies/min. 22 copies/min. 45 copies/min. 30 copies/min

Scanner module

B/W scanner module/DSPF Two-side simultaneous scanning system from the document feeder. One-sided scanning from the document glass Original feed system Automatic continuous feeding Original exit system Face down output Original transport system DSPF: sheet through type (reference position: center), document glass: reference position is left rear Original setting direction Face down Original sizes 5-1/2" x 8-1/2" to 11" x 17" or A5 to A3 Original weight 14 to 34 lbs. or 50 to 128 g/m2 Capacity Up to 50 sheets (30 sheets*1 for 8-1/2" x 14" or B4 or larger originals) provided the total aggregate thickness does not exceed 1/4" or 6.5 mm (14 to 20 lbs. or 50 to 80 g/m2) or 3/16" or 5 mm (21 to 34 lbs. or 80 to 128 g/m2) Power supply Drawn from the main unit Dimensions 31-13/16" (W) x 24-3/8" (D) x 7-3/32" (H) or 808 mm (W) x 619 mm (D) x 180 mm (H) Weight Approx. 43 lbs. or 19.5 kg *1 For paper heavier than 28 lbs. (105 g/m2), only a stack of up to 15 sheets can be set. If 16 or more sheets are set, image can not be scanned properly and scanned image can be expanded compared with original itself. Name Type

KEY OPERATOR PROGRAMS

This section describes all key operator programs relating only to the copier and facsimile functions. For the key operator programs which relate to copier, printer and facsimile functions, see the Operation manual (for printer operation and general information).
Key operator program list
Program name Copy function settings Initial status settings Exposure adjustment Rotation copy setting Auto paper selection setting 600dpi x 600dpi scanning mode Quick scan from document glass Device control Original size detector setting Disabling of document feeder Page 34 34
Using the key operator programs
To use of the key operator programs, follow the procedures described in the Operation manual (for printer operation and general information) on page 7-6. Also read Supplementary explanation of key operation for key operator programs on page 7-6.

Setting programs

This section describes the setting of programs common to copier, facsimile and network scanning features. For programs dedicated to facsimile, network scanning and programs common to both the copier and printer features, see their respective manuals.

Copy function settings

The following programs can be set in Copy function settings. q Initial status settings q Exposure adjustment q Rotation copy setting q Auto paper selection setting q 600dpi x 600dpi scanning mode q Quick scan from document glass

Initial status settings

The copier settings will be reset when the main switch is turned off, when the [CA] key is pressed or when the auto clear interval has elapsed. Use this program to establish new initial settings or to return the initial settings to the factory default settings. Paper tray, exposure mode, copy ratio, duplex mode, and output mode default settings can be made.
Auto paper selection setting
Use this program to set the paper type* for the auto paper select mode to Plain paper or Plain paper and recycle paper. * Paper type specified in Tray setting of the custom setting function (page 1-20 of Operation manual (for printer operation and general information))
600dpi x 600dpi scanning mode
NOTE If a duplex mode other than 1-sided to 1-sided is set as the default and either the duplex or scanner mode is disabled*, the default will change to the 1-sided to 1-sided mode. * Disable duplex unit (page 7-10 of the Operation manual (for printer operation and general information)) * Disabling of document feeder (page 34)

Use this program to change the original scanning resolution of the automatic document feeder from 600 x 300 dpi to 600 x 600 dpi. If this mode is set, the copy quality for fine characters and fine lines will be improved but the original scanning speed will be slower.
NOTE If the original scanning speed is more important than higher resolution, do not set this program.

Exposure adjustment

Use this program to lighten or darken copies in the automatic exposure mode. The factory setting is 5. 1 indicates lighter density and 9 indicates darker density on the touch panel.
Quick scan from document glass
Use this program to change the original scanning resolution on the document glass from 600 x 600dpi to 600 x 300 dpi. If you set this program, the first copy time will be shorter but the copy image will become a little more coarse.
NOTE If the copy image quality is more important than first copy time, do not set this program.

Rotation copy setting

If this program is set, the image of originals will rotate when the orientation of the originals does not match that of the copy paper. (Rotation copy will function only if the auto paper select or auto image mode has been selected.)
NOTE For copying from 5-1/2 x 8-1/2 or A5 size originals onto 51/2 x 8-1/2R or A5R paper, this program must be set.

Device control

Original size detection and disabling of the document feeder can be set.
Original size detector setting
This program is used to select the group of original sizes to be detected. Original size detection from the document glass can be disabled using the program CANCEL DETECTION AT DOCUMENT GLASS. Detectable original sizes Document feeder tray (for automatic document feeding) Document glass 11 x 17, 8-1/2 x 14, 8-1/2 x 11, 8-1/2 x 11R, A4 5-1/2 x 8-1/x 17, 8-1/2 x 13, 8-1/2 x 11,8-1/2 x 11R, A4 5-1/2 x 8-1/2 A3, A4, A4R, A5, 8-1/2 x 11, B4, B5, B5R 216 x 330 A3, A4, A4R, A5, 8-1/2 x 11, B5, B5R, 216 x 330 B4

INCH - 1

INCH - 2 AB - 1 AB - 2
If CANCEL DETECTION AT DOCUMENT GLASS is set, originals will be regarded as EXTRA for all copier functions and no original size will be displayed.
Disabling of document feeder
This program is used to prevent use of the automatic document feeder when the scanner module malfunctions. In this case scanning can still be done off the document glass.
Operation manual for copier

SHARP CORPORATION

PRINTED IN CHINA

2001D KS1 TINSE2078FCZZ

P350,P450,3500,3501 3551,4500,4501,4551