ENGLISH

OPERATIONAL NOTES

To insure trouble-free operation of your SHARP calculator, we recommend the following: 1. The calculator should be kept in areas free from extreme temperature changes, moisture, and dust. 2. A soft, dry cloth should be used to clean the calculator. Do not use solvents or a wet cloth. 3. Since this product is not waterproof, do not use it or store it where fluids, for example water, can splash onto it. Raindrops, water spray, juice, coffee, steam, perspiration, etc. will also cause malfunction. 4. While the memory protection battery is not installed, the tax / discount rate and conversion rate set up will be cleared upon terminating the AC power supply. The tax / discount rate and conversion rate set up will also be cleared when the memory protection battery is removed from the unit. 5. If service should be required on this equipment, use only a SHARP servicing dealer, a SHARP approved service facility or SHARP repair service where available. 6. Do not wind the AC cord around the body or otherwise forcibly bend or twist it. 2

CONTENTS

Page INSTALLING OF BATTERY FOR MEMORY PROTECTION... 3 OPERATING CONTROLS.. 4 INK RIBBON REPLACEMENT.. 8 PAPER ROLL REPLACEMENT. 9 ERRORS.. 10 REPLACEMENT OF BATTERY FOR MEMORY PROTECTION.. 11 SPECIFICATIONS.. 12 RESETTING THE UNIT.. 14 CALCULATION EXAMPLES.. 121 CONVERSION CALCULATION EXAMPLES... 144 TAX RATE CALCULATIONS.. 146 DISCOUNT RATE CALCULATION.. 149 SHARP will not be liable nor responsible for any incidental or consequential economic or property damage caused by misuse and/or malfunctions of this product and its peripherals, unless such liability is acknowledged by law.

03.3.13, 8:19 PM

INSTALLING OF BATTERY FOR MEMORY PROTECTION
Before using for the first time, remove the attached lithium battery, and install it in the equipment according to the following procedure. If the power cord is unplugged by accident when operating with AC power only, the tax / discount rate and conversion rate set up will be lost. 1) Turn the power switch OFF and unplug the power supply plug from the outlet. 2) Remove the battery cover on the back of the unit. (Fig. 1) 3) Wipe the battery well with a dry cloth and place the plus + side upward. (Fig. 2) 4) Replace the battery cover by reversing the removal procedure. 5) Press the RESET switch on the back of the unit (See page 14).

Fig. 1

Fig. 2
After battery installation Connect the power supply plug to an outlet and turn the power switch ON. Check that 0. is displayed. If 0. is not displayed, remove the battery, reinstall it, and check the display again. On the battery replacement date label found on the back of the unit, write down the month and year when the battery is installed, as a reference for the next battery replacement.

3 03.3.12, 2:33 PM

OPERATING CONTROLS
POWER SWITCH; PRINT / ITEM COUNT MODE SELECTOR: OFF: Power OFF. : Power ON. Set to the nonprint mode. ( . P will be printed.) P: Power ON. Set to the print mode. ( . +P will be printed.) PIC: Power ON. Set to the print and item count mode. The counter will count the number of times that has been pressed in addition. is used in Notes: Each time subtraction, 1 will be subtracted from the count. The count is printed when the calculated result is obtained. Pressing of , or clears the counter. 4
The counter has a maximum capacity of 3 digits (up to 999). If the count exceeds the maximum, the counter will recount from zero. RATE SETTING MODE SELECTOR: This selector is used to set the conversion rate or the tax / discount rate. : Set this selector to the RATE SET position before storing an each rate. Conversion rate: Enter the conversion rate, then press. A maximum of 6 digits can be stored (decimal point is not counted as a digit). Tax / discount rate: Enter the adding tax rate, then press. To store a discount rate, press before pressing. A maximum of 4 digits can be stored (decimal point is not

03.3.12, 2:33 PM

counted as a digit). Set this selector to the position before starting calculations. Note: Be sure to set this selector to the position after storing an each rate. For the conversion rate and the tax / discount rate, a single value can be stored for each. If you enter a new rate, the previous rate will be cleared. : CONSTANT / ADD MODE SELECTOR: K : The following constant functions will be performed: Multiplication: The calculator will automatically remember the first number entered (the multiplicand) and instruction.

Division:

The calculator will automatically remember the second number entered (the divisor) and instruction.
: Neutral A: Use of the Add mode permits addition and subtraction of numbers without entry of the decimal point. When the Add mode is activated, the decimal point is automatically positioned according to the decimal selector setting. Use of , , and will automatically override the Add mode and decimally correct answers will be printed at the preset decimal position.

5 03.3.12, 2:33 PM

ROUNDING SELECTOR: Example: Set decimal selector to 2. = 0.444. , = 0.555. 4 5/0.45 0.44 0.9 0.56 0.56 0.55
CONVERSION KEY: This key is used to obtain a value by dividing a given number with a specified conversion rate. CONVERSION KEY: This key is used: to store the conversion rate (by the use of the rate setting mode selector). obtains a value by multiplying a given number with a specified conversion rate. to recall the presently stored rate for check. Press first to clear the calculation register and reset an error. The condition, then press conversion rate is printed with the symbol TC. LAST DIGIT CORRECTION KEY CLEAR ENTRY KEY: Clears numbers entered prior to use of a function key. Also used to clear an overflow error caused by an entry. 6

Note: The decimal point floats during successive calculation by the use of or. If the decimal selector is set to F then the answer is always rounded down ( ). DECIMAL SELECTOR: Presets the number of decimal places in the answer. In the F position, the answer is displayed in the floating decimal system. PAPER FEED KEY
NON-ADD / SUBTOTAL KEY: Non-Add When this key is pressed right after entry of a number in the Print mode, the entry is printed on the left-hand side with #. This key is used to print out numbers not subject to calculations such as codes, dates, etc. Subtotal Used to get subtotal(s) of additions and / or subtractions. When pressed following or , the subtotal is printed with and the calculation may be continued. By pressing this key even in the Non-print mode, the displayed number is printed with P. TOTAL KEY: Prints the total of addition and subtraction with . This key also serves as a clear key for the calculation register and resets an error condition.
FIRST RECALL MEMORY KEY FIRST RECALL MEMORY KEY AND CLEAR
SECOND RECALL AND CLEAR MEMORY KEY SECOND RECALL MEMORY KEY CHANGE SIGN KEY: Changes the algebraic sign of a number (i.e. positive to negative or negative to positive). MULTIPLE USE KEY: Performs mark-ups, percent change and automatic add-on / discount. TAX-INCLUDING KEY: This key is used for calculations with the tax/discount rate. To recall the presently stored rate for check, press to clear the calculation register and reset an error condition,. The tax / discount rate then press is printed with the symbol TX.

DISPLAY Display format:

INK RIBBON REPLACEMENT
1. Remove the paper roll from the calculator. (Tear the paper and remove it from the print mechanism by using.) 2. Set the power switch to OFF. Make sure that the print wheel has stopped. 3. Remove the printer cover by sliding it towards the back of the calculator. (Fig. 1) 4. Remove the used ribbon. 5. Install the new ribbon. 6. With the black side of the ribbon facing upwards, place one of the reels on the reel shaft on the right. (Fig. 2) Make sure that the reel is securely in place. 7. Thread the ribbon around the outside of the metal guides. (Fig. 3) 8. Take up any slack by manually turning one of the reels. 9. Replace the printer cover. 10. Replace the paper roll.
Symbols: M : First memory symbol Appears when a number has been stored in First memory. : Second memory symbol Appears when a number has been stored in Second memory. : Minus symbol Appears when a number is a negative. E : Error symbol Appears when an overflow or other error is detected. * Although all available symbols are shown here for instruction purposes, these symbols will not appear on the screen simultaneously.

8 03.3.12, 2:33 PM

Printer cover

Ink ribbon

PAPER ROLL REPLACEMENT
1. Lift the paper holder up. (Fig. 1) 2. Fold the leading edge of the paper roll 3 to 5 cm. (Do not fold it slantwise.) (Fig. 2) 3. Insert the paper roll from the left side of the paper holder and make sure the paper roll is set in the proper direction (with the paper feeding from the bottom). (Fig. 3) 4. Insert the leading edge of the paper into the opening directly behind the print mechanism. (Fig. 4) 5. Press the paper feed key and feed the paper under the edge of the paper cutter. (Fig. 5)

Paper holder

3 cm 5 cm (1-3/16 to 1-31/32)

Reel shaft Ink ribbon

Fig. 3 Fig. 1 Fig. 2

9 03.3.12, 2:33 PM

ERRORS
There are several situations which will cause an overflow or an error condition. When this occurs, the error symbol E will be displayed and all keys will electronically lock. The contents of the memory at the time of the error are retained. If an 0E is displayed at the time of the error, must be used to clear the calculator. If an E with any numerals except zero is displayed, the error may be cleared with or and the calculation can still be continued. Error conditions: Fig. 4 Fig. 5 1. Entry of more than 12 digits or 11 decimals. This error can be cleared with or. 2. When the integer portion of an answer exceeds 12 digits. 3. When the integer portion of the contents of the memory exceeds 12 digits. (Ex. ) 4. When any number is divided by zero. 0 ) (Ex. 5

Fig. 3

Paper cutter
DO NOT PULL PAPER BACKWARDS AS THIS M AY C A U S E D A M A G E T O P R I N T I N G MECHANISM.

10 03.3.12, 2:33 PM

REPLACEMENT OF BATTERY FOR MEMORY PROTECTION
Time for battery replacement Replace with a new battery once 2 year. Method of battery replacement Use one lithium battery (CR2032). Note: When replacing the battery, the set tax / discount rate and conversion rate, the memory contents will be lost. You may want to write down the tax / discount rate and conversion rate, other important numbers on a sheet of paper. 1) Turn the power switch OFF and unplug the power supply plug from the outlet. 2) Remove the battery cover on the back of the unit. (Fig. 1) 3) Remove the exhausted battery and install one new lithium battery. Wipe the battery well with a dry cloth and place the plus + side upward. (Fig. 2) 4) Replace the battery cover by reversing the removal procedure. 5) Press the RESET switch on the back of the unit (See page 14).

After battery replacement Connect the power supply plug to an outlet and turn the power switch ON. Check that 0. is displayed. If 0. is not displayed, remove the battery, reinstall it, and check the display again. Reset the tax / discount rate and conversion rate. On the battery replacement date label found on the back of the unit, write down the month and year when the battery is replaced, as a reference for the next battery replacement.

11 03.3.12, 2:33 PM

, , , , , , , , , ,
Precautions on battery use Do not leave an exhausted battery in the equipment. Do not expose the battery to water or flame, and do not take it apart. Store batteries out of the reach of small children.

SPECIFICATIONS

Operating capacity: Power supply: 12 digits Operating: AC: 220V230V, 50Hz Memory backup: 3V (DC) (Lithium battery CR2032 1) Memory Protection Battery lifespan: Approx. 2 years. (tested and confirmed at 25C (77F); may change due to usage environment) Calculations: Four arithmetic calculations, constant multiplication and division, power calculation, add-on / discount calculation, repeat addition and subtraction, reciprocal calculation, item count calculation, markup calculation, memory calculation, etc.

12 03.3.12, 2:33 PM

PRINTING SECTION Printer: Printing speed: Printing paper:
WARNING THE VOLTAGE USED MUST BE THE SAME AS SPECIFIED ON THIS CALCULATOR. USING THIS CALCULATOR WITH A VOLTAGE H I G H E R T H A N T H AT S P E C I F I E D I S DANGEROUS AND MAY RESULT IN A FIRE OR OTHER TYPE OF ACCIDENT CAUSING DAMAGE. SHARP WILL NOT BE HELD RESPONSIBLE FOR ANY DAMAGE R E S U LT I N G F R O M U S E O F T H I S CALCULATOR WITH OTHER THAN THE SPECIFIED VOLTAGE.
Mechanical printer Approx. 4.3 lines/sec. 57 mm (2-1/4") ~ 58 mm (2-9/32") wide 80 mm (3-5/32") in diameter (max.) Operation temperature: 0C ~ 40C (32F ~ 104F) Power consumption: 53 mA Dimensions: 250 mm (W) 345 mm (D) 78 mm (H) 9-27/32" (W) 13-19/32" (D) 3-1/16" (H) Weight: Approx. 2.0 kg (4.41 lb.) (with battery) Accessories: 1 lithium battery, 1 battery replacement date label (attached on the units back body), 1 paper roll, 1 ink ribbon (installed) and operation manual

13 03.5.21, 3:56 PM

RESETTING THE UNIT
Strong impacts, exposure to electrical fields, or other unusual conditions may render the unit inoperative, and pressing the keys will have no effect. If this occurs, you will have to press the RESET switch on the bottom of the unit. The RESET switch should be pressed only when: an abnormal event occurs and all keys are disabled. you install or replace the battery. Notes: Pressing the RESET switch will clear the stored tax / discount rate and conversion rate, other data stored in the memory. Use only a ballpoint pen to press the RESET switch. Do not use anything breakable or anything with a sharp tip, such as a needle. After pressing the RESET switch, connect the power supply plug to an outlet. Turn the power switch ON and check that 0. is displayed.

14 03.3.12, 2:33 PM

CALCULATION EXAMPLES
1. Set the decimal selector as specified in each example. The rounding selector should be in the 5/4 position unless otherwise specified. 2. The rate setting mode selector and the constant/ add mode selector should be in the position (off position) unless otherwise specified. 3. The print/item count mode selector should be in the P position unless otherwise specified. 4. If an error is made while entering a number, press or and enter the correct number. 5. Negative values are printed with symbol in red. Note: All totals and sub-totals may be used for further calculations. RE-ENTER the number into the calculator by using the FUNCTION key and continue the problem.

RECHNUNGSBEISPIELE

1. Stellen Sie den Komma-Tabulator wie in jedem Beispiel beschrieben ein. Der Rundungs-Wahlschalter sollte auf die Position 5/4 eingestellt sein, falls nicht anderweitig angegeben. 2. Der Umrechnungsrate-Wahlschalter und der Konstantenbetriebs/Additionshilfe-Wahlschalter sollten sich in der Position (ausgeschaltet) befinden, wenn nicht anders angegeben. 3. Der Wahlschalter fr Drucken/Postenzhler sollte auf die Position P eingestellt sein, falls nicht anderweitig angegeben. 4. Wenn Sie bei der Eingabe von Zahlen einen Fehler machen, drcken Sie oder und geben Sie die richtige Zahl ein. 5. Negative Zahlen werden mit einem roten Minuszeichen ausgedruckt. Hinweis: Alle Summen und Zwischensummen knnen fr weitere Berechnungen verwendet werden. GEBEN Sie die Zahl ERNEUT mit der FUNKTIONSTASTE ein und fahren Sie mit der Berechnung fort. 121

03.3.12, 2:17 PM

EXEMPLES DE CALCULS
1. Rgler le slecteur de dcimale tel que spcifi dans chaque exemple. Le slecteur darrondi, doit tre plac la position 5/4 sauf indication contraire. 2. Le slecteur de rglage de taux et le slecteur constante/addition doivent tre placs sur la position (position darrt) sauf indication contraire. 3. Le slecteur de mode dimpression, et le slecteur de mode du compteur darticles doivent tre placs la position P sauf indication contraire. 4. En cas derreur lintroduction dun nombre, ou et introduire le nombre appuyer sur correct. 5. Les valeurs ngatives sont accompagnes du symbole imprim en rouge. Remarque: Tous les totaux et les totaux partiels peuvent tre utiliss pour des calculs ultrieurs. RINTRODUIRE le nombre dans la calculatrice en utilisant une touche de FONCTION et poursuivre le calcul.

12. 5 60.

128 03.3.12, 2:17 PM

CONSTANT / KONSTANTE / CALCULS AVEC CONSTANTE / CONSTANTES / COSTANTE / KONSTANTRKNING / CONSTANTE / CONSTANTE / VAKIO A. 62.35 11.11 = 62.35 22.22 = (1) 62.35 11.11 (2) 62.35 (3) 62.35 11.11 =K 692.71 22.22 =K 1,385.42 1,385.42
B. 11.11 77.77 = 22.22 77.77 = (1) 11.11 77.77 (2) 11.11 (3)
11.11 77.77 =K 0.143 22.22 =K 0.286

0.143 22.22 0.286

692.71 22.22

129 03.3.12, 2:17 PM

POWER / POTENZ / PUISSANCE / POTENCIA / POTENZA / POTENSRKNING / MACHTSVERHEFFEN / POTNCIA / POTENSSI A. 5.252 = (1) 5.25 (2) 5.25 (3) 5.25 5.25 = 27.563

B. 53 = (1) 5 (2) 5. (3)

5. 5. =K 25. 25. =K 125.

27.563

5. 25.

5. 5. 5. = 125.

130 03.3.12, 2:17 PM
PERCENT / PROZENT / POURCENTAGE / PORCENTAJES / PERCENTUALE / PROCENTRKNING / PERCENTAGE / PORCENTAGEM / PROSENTTI A. 100 25% = (1) (2) 100. (3) 100. 25. % 25.00
RECIPROCAL / KEHRWERT / INVERSES / RECPROCOS / RECIPROCO / RECIPROKA TAL / RECIPROQUE / RECPROCA / KNTEISARVO 1 = 7 (1) 7 (2) 7. 1.
(3) 7. 7. 7. = 0.14285714285
25.00 B. (123 1368) 100 = (1) (2) 123. (3) 123. 1,368. % 8.99

0.14285714285

131 03.4.17, 4:16 PM
A. 5% add-on to 100. / Ein Aufschlag von 5% auf 100. / Majoration de 5% de 100. / Un 5% de recargo sobre 100. / Maggiorazione del 5% su 100. / 5% tillgg p 100. / Een opslag van 5% op 100. / Um acrscimo de 5% sobre 100. / 5% listn 100:aan

105.00

New amount Neuer Betrag Total major Nueva cantidad.00 Nuovo importo 105 Nytt belopp Nieuwe bedrag Nova quantia Uusi mr

132 03.3.12, 2:17 PM

ADD-ON AND DISCOUNT / AUFSCHLAG UND ABSCHLAG / MAJORATION ET RABAIS / RECARGOS Y DESCUENTOS / MAGGIORAZIONE E SCONTO / TILLGG OCH RABATT / OPSLAG/KORTING / ACRSCIMO E DESCONTO / LISYS/VHENNYS

(1) 100 5

(2) 100. 100. 5. %
Increased amount Erhhung Majoration Incremento Importo incrementato Tillagt belopp Extra bedrag Quantia aumentada Listty mr
B. 10% discount on 100. / Ein Abschlag von 10% auf 100. / Rabais de 10% sur 100. / Un 10% de descuento sobre 100. / Sconto del 10% su 100. / 10% rabatt p 100. / Een korting van 10% op 100. / Desconto de 10% de 100. / 10% vhennys F643210 100:sta. (1) (2) 100. 100. 10. % (3)
MARKUP AND MARGIN / GEWINNAUFSCHLAG UND GEWINNSPANNE / HAUSSE ET MARGE BNFICIAIRE / INCREMENTO PORCENTUAL Y MARGEN / MARGINE LORDO E MARGINE NETTO / PSLAG OCH MARGINAL / PROCENTUELE VERHOGING EN WINSTMARGE / REMARCAO PARA CIMA E MARGEM / VOITTOMARGINAALI JA VOITTO Markup and Profit Margin are both ways of calculating percent profit. Profit margin is percent profit vs. selling price. Markup is percent profit vs. cost. Cost is the cost. Sell is the selling price. GP is the gross profit. Mkup is the percent profit based on cost. Mrgn is the percent profit based on selling price.