VX1 Users Guide

IMPORTANT NOTICE LXEs VX1 is obsolete. This electronic manual has been made available as a courtesy to LXE's VX1 customers. Please contact your LXE customer support representative for assistance and mobile device replacement.
Copyright 2006 by LXE Inc. All Rights Reserved E-EQ-VX1OGWW-K-ARC

LANGUAGE : ENGLISH

Notices

Notice:

LXE Inc. reserves the right to make improvements or changes in the products described in this publication at any time without notice. While reasonable efforts have been made in the preparation of this publication to assure its accuracy, LXE assumes no liability resulting from any errors or omissions in this publication, or from the use of the information contained herein. Further, LXE Incorporated, reserves the right to revise this publication and to make changes to it from time to time without any obligation to notify any person or organization of such revision or changes.

Copyright Notice:

This user guide is copyrighted. All rights are reserved. This guide may not, in whole or in part, be copied, photocopied, reproduced, translated or reduced to any electronic medium or machine-readable form without prior consent, in writing, from LXE Inc. Copyright 2006 by LXE Inc. An EMS Technologies Company. 125 Technology Parkway, Norcross, GA 30092 U.S.A. (770) 447-4224

Trademarks:

LXE is a registered trademark of LXE Inc. All other brand or product names are trademarks or registered trademarks of their respective companies or organizations. When this publication is in PDF format: Acrobat Reader Copyright 2006 Adobe Systems Incorporated. All rights reserved. Adobe, the Adobe logo, Acrobat, and the Acrobat logo are trademarks of Adobe Systems Incorporated. applies.
The user is strongly encouraged to read Appendix B, Regulatory Notices and Safety Information. Important safety cautions, warnings and regulatory information is contained in Appendix B.
Important: This symbol is placed on the product to remind users to dispose of Waste Electrical and Electronic Equipment (WEEE) appropriately, per Directive 2002-96-EC. In most areas, this product can be recycled, reclaimed and re-used when properly discarded. Do not discard labeled units with trash. For information about proper disposal, contact LXE through your local sales representative, or visit www lxe com.

Revision Notice

Obsolete/Archived. Available on LXE ServicePass website only. Products replacement device is the LXE VX6. Entire Manual Added Hungary to R&TTE Directive Requirements. Updated document presentation to reflect LXEs 2006 documentation standards. Updated Accessories. Updated Manuals. Added section titled Revision History.
Table of Contents THE VX1 VEHICLE MOUNT COMPUTER 1
Introduction.... 1 Document Conventions...2 Environmental Specifications....2 Quick Start..... 3 Components.... 4 The Half-Screen Display... 5 Controls and Connectors.... 5 The Keyboards.... 6 The ABCD Keyboard....6 The QWERTY Keyboard....6 IBM 3270 Overlay.....7 IBM 5250 Overlay.....7 Key Maps.....7 DOS Key Functions Not Available on the VX1...8 Keyboard LEDs....9 CAPS LED.....9 Secondary Keys LED....10 Status LED.....11 Control Keys.....12 PCMCIA Slots.... 13 Radio Cards....13 Power Supply.... 14 Backup Battery....14 Getting Help.... 15 Manuals and Accessories... 15 Manuals.....15 Accessories.....16 Revision History....17 INSTALLATION 19
Install Mounting Brackets... 19 Components....19 Mounting Dimensions...20 Mounting Positions.....20 Torque Measurements...21 Cable Retention Assembly....22 Connect Cable Ties to Back Mounting Bracket..23 Procedure.....24 Step 1 - Mount Bottom Mounting Bracket To Vehicle...24

E-EQ-VX1OGWW-K-ARC

Table of Contents
Step 2 - Connect VX1 To Back Mounting Bracket..25 Step 3 - Attach VX1 In Bracket Assembly To Bottom Mounting Bracket.26 Connect Antenna.... 28 Vehicle Remote Antenna Mount....28 Connect Serial Barcode Scanner... 29 Connect Serial Printer or PC.... 31 Connect Power Cable... 32 External Power Supply, Optional... 33 Vehicle 12-60VDC Direct Connection... 34 Vehicle 12-80VDC Direct Connection... 36 Fuse Replacement for the VX1... 38 OPERATION 39
Powering On/Off.... 39 Reset Key Sequence (Reboot)...40 Factory Default Settings...40 Power On Default Settings....40 Cleaning the Glass Display/Scanner Aperture... 41 Adjust Screen Display.... 41 Set Display Brightness...41 Keyboard Backlight Control Key... 42 Set Speaker Volume.... 42 Panning the Display... 43 Power Status and the Status LED... 45 Normal Mode....45 Video Timeout State....46 Suspend Mode....46 Critical Suspend State....47 Laser Barcode Scanner Warnings... 48 Enter Data.... 49 Keyboard Entry....49 Scanner Entry....49 Aiming the Barcode Scanner...49 Distance from Label....50 Successful Scan....50 Unsuccessful Scan....50 Cleaning the Scanner Aperture....50 CHAPTER 1 KEY MAPS 51

Control Keys

The VX1 has several control keys. One key controls the keyboard backlight, a pair of keys controls the volume and another pair of keys controls the display brightness. The VX1 must be placed in Secondary Mode to access these functions. Note: The <F6> and <F7> keys (Contrast Up and Contrast Down) have no function as the VX1 has an electroluminescent screen. Contact your LXE representative for future enhancements using these keys.
Display Brightness Control Keys Display Contrast Control Keys (Not Used) Speaker Volume Control keys Backlight Control Key
Figure 10 The VX1 Display Controls

PCMCIA Slots

The VX1 has one active PCMCIA slot the right slot, slot 0. It supports the Personal Computer Memory Card International Association (PCMCIA) 2.1 standards. Slot 0 (the right slot, usually configured as Drive D:) accepts Type I, II or III PCMCIA SRAM cards. LXE supports only Type II 2.4GHz Spread Spectrum and Type III 900MHz Spread Spectrum radios. Slot 1 (the left slot) is not used.
Slot 1 (Left) Unused Slot 0 (Right)
Figure 11 The VX1 PCMCIA Slots

Radio Cards

Common use of the PC slot is to insert a radio PCMCIA card or a memory/ SRAM card. Not all units require radio cards or memory cards. Possible radio configurations are: LXE TE Software ANSI Plus LDS Plus IBM 3270/IBM 5250 IBM TN3270/TN5250 x 2.4GHz x x 900MHz x x x

Power Supply

Vehicle power input for the VX1 is 12V to 80V DC and is accepted without the need to perform any manual adjustments within the VX1. See the section titled Installation, sub-section titled Vehicle 12-80VDC Direct Connection. If 12V to 80V DC power is not available for example, in an office environment an optional external Universal Input Power Supply can be used to convert AC wall power to an appropriate DC level. See the section titled Installation, sub-section titled External Power Supply. Power input is fused for protection and the fuse is externally accessible. See section titled Installation, sub-section titled Fuse Replacement for the VX1.

Backup Battery

The internal 50mAh Nickel Cadmium (NiCd) backup battery provides power to the unit for a short amount of time when the primary power supply has been depleted, removed or has failed. The backup battery requires no user intervention other than periodic conditioning (see Appendix D "Utilities" in the VX1 Reference Guide). Replacement is performed by LXE. Note: When there is no external power supplied to the VX1, the unit is powered by the backup battery. When the backup battery is depleted, the BIOS parameters are reset to their factory default settings.

When using the 8500 series tethered scanners (LS3408), the tethered scanner Power Mode must be set to Reduced Power Mode. The default is Continuous On. Setting the scanner to reduced power mode will not impact performance of the 8500 series tethered scanners. Refer to the manufacturers user guide for instruction. Note A: Adapter Kit Includes Hardware and Adapter Power Cord to mount a VX1/2 Computer utilizing the existing 1280 mounting bracket. Integrated keyboard bracket can not be used in conjunction with the adapter bracket. Note B: This power filter may be required when customers have unclean forklift power in which power spikes cause problems with the vehicle computer.

Revision History

Revision J October 2005 Entire Manual : Updated document presentation to reflect LXEs 2005 documentation standards. Added 2005 LXE logo. Added WEEE statement to Notices and Appendix B. Marked obsolete tethered scanners in Accessories. Noted obsolescence of 900MHz radios (and companion TE software) and the Symbol 2Meg radio. Added up-to-date Getting Help including Manuals and Accessories. Revision H August 2004 Introduction : Added 8500 Series Tethered Scanners to Accessories. Added Power Settings recommendation for 8500 Scanners. Updated Accessories listing effective July 2004. Appendix B Regulatory Notices and Safety Information : Updated the 6726 Declaration of Conformity. Revision G May 2004 Entire Manual : Renamed to VX1 Users Guide from VX1 Installation and Operators Guide. Installation : Added section titled Vehicle Remote Antenna Mount. From the Vehicle Power Supply Installation procedure, removed The green wire is not used. Do not connect this wire. If the green wire has a bare end, use electrical tape (or otherwise insulated) to cover the bare end and ensure the bare wire does not contact anything. The VX1 must be grounded when installed in a vehicle. Revision F July 2003 Appendix B Regulatory Notices and Safety Information : Revised Approvals table. Added 6816 Declaration of Compliance. Revision E September 2002 Installation : Added 12-60VDC Direct Connection Instruction. Added information for negative and floating ground vehicles. Added non-conducting strap information. Added Ground Wire Not Used note. Operation : Added new phrasing for Cleaning the Display/Scanner Aperture. Revision D June 2002 Appendix B Regulatory Notices and Safety Information : Revise Approvals table. Revise A/C Power Supply Safety Statement. Revision A April 2001, Initial Release

Installation

Install Mounting Brackets
Caution: This device is intended to transmit RF energy. For protection against RF exposure to humans and in accordance with FCC rules and Industry Canada rules, this transmitter should be installed such that a minimum separation distance of at least 20 cm (7.8 in.) is maintained between the antenna and the general population. This device is not to be co-located with other transmitters. Equipment Needed: Phillips No. 1 screwdriver and a Torque wrench capable of measuring to 50 inch pounds (5.64.56 N/m). Note: Note: Torquing tool is not supplied by LXE. Bolts, washers, and wrench needed when attaching the bottom mounting bracket to the vehicle are not supplied by LXE.

Before installation begins, verify you have the following vehicle mounting bracket assembly components:
Back Mounting Bracket Assembly This bracket is attached to the VX1. It is preassembled at LXE. 6 each 8-32 x 7/16 Pan Head Screw (connects to the back of the computer) 6 each 8-32 x 3/8 Flat Screw (connects to the side of the computer)
Bottom Mounting Bracket This bracket is mounted to the vehicle. Then it is connected to the Back Mounting Bracket and VX1 assembly. 6 each 1/4 Flat Washer 6 each 1/4 Lock Washer 6 each -20 Bolt

Mounting Dimensions

9 14.40 in / 359.2 mm 12.10 in / 307.3 mm 6.05 in / 153.6 mm 1.02 in / 25.9 mm 3.00 in / 76.2 mm Vehicle Mount Footprint 0.18 in / 4.5 mm 0.88 in / 22.3 mm 1.25 in / 31.75 mm
Figure 12 VX1 Bracket - Mounting Dimensions (Not To Scale)

Mounting Positions

Figure 13 Suggested Mounting Positions Viewing angle is 45 to both sides of the bottom mounting bracket.

Torque Measurements

You will need a torquing tool capable of torquing to 50 inch pounds (5.64.56 N/m). Torque pan head screws to 16.01 in/lb (1.8.11 N/m) when assembling the back mounting bracket to the VX1. Torque bolts to 50.05 in/lb (5.64.56 N/m) when assembling the bottom mounting bracket to the back mounting bracket.
Figure 14 Torque Measurements

Cable Retention Assembly

Before beginning the vehicle mounting bracket assembly, attach the cable ties to the VX1 and the back mounting bracket as shown in the following figures. Use the cable ties to secure the power cable and RS-232 cables to the VX1 after it has been mounted to the vehicle.
(5) Strain Relief Cable Clamps and (2) Cable Ties Connect Strain Relief Cable Clamps to the back of the VX1. Connect Cable Ties to the VX1 and the back mounting bracket.

7 each Screw

8-32 x 7/16 Pan Head
Turn the VX1 off before attaching the accessories. Install accessories and the strain relief cable clamps. Mount the accessories cable to the VX1 with the strain relief cable clamps, ensuring a slack loop remains between the cable clamp and the accessories connectors.
Figure 15 Strain Relief Cable Clamp Locations 4. Insert a pan head screw into the screw holes and fasten securely.
Connect Cable Ties to Back Mounting Bracket
Figure 16 Cable Ties on Back Mounting Bracket Assembly 1. 2. 3. Slide the pointed end of the cable tie through the top opening in the push mount. Snap the push mount through the top hole and toward the VX1 as shown in the above figure. Place the cable (power, COM port) over the tie and lift up the pointed end of the tie. Slide it through the narrow opening at the top of the cable tie, keeping the serrated sides together. Slide the tail of the cable tie closed until cables are snug.

Procedure

Step 1 - Mount Bottom Mounting Bracket To Vehicle.

1. 2. Position the bracket to allow access to the switches and ports on the bottom of the VX1. Attach the bottom mounting bracket to the vehicle mounting surface using six 1/4 bolts (or equivalent) fasteners. Note: 1/4 Bolts not included.
IMPORTANT: Mount to the most rigid surface available.
Figure 17 Connect Bottom Bracket to Vehicle After the bottom bracket has been attached to a rigid, horizontal surface, you are ready to assemble the VX1 bracket configuration.
Step 2 - Connect VX1 To Back Mounting Bracket.
Figure 18 Back Mounting Bracket Assembly 1. 2. 3. 4. Turn the VX1 off before attaching it to the back mounting bracket. Place the VX1 face down on a stable surface. Position the back mounting bracket on the VX1, matching the screw holes in the bracket to the screw holes on the back of the VX1. Insert a pan head screw into each of six holes. Torque the screws to 161 in/lb (1.8.11 N/m).
Figure 19 VX1 Connected to Back Bracket Now you are ready to attach the VX1 in the bracket assembly to the vehicle.
Step 3 - Attach VX1 In Bracket Assembly To Bottom Mounting Bracket.
Figure 20 Connect to Bottom Mounting Bracket 1. 2. Insert mounting bolts (place washer first, then the lock washer) through the curved apertures in the bottom mounting bracket and into the screw holes in the side bracket. Loosely tighten each bolt as it is inserted. Important: 3. 4. Do not torque bolts until all bolts are in place and viewing angle is adjusted.
Loosen the hex bolts on both sides to adjust the viewing angle of the mounted VX1. Torque the hex bolts to 505 in/lb (5.64.56 N/m). Note: Test the torque on the bolts frequently during operation and re-tighten if necessary to 505 in/lb (5.64.56 N/m).
Connect all cables to the VX1. Secure the cables with the strain relief cable clamps, ensuring a slack loop remains between the cable clamp and the accessory connector. The vehicle mounted bracket and the VX1 are now ready to use.
Figure 21 VX1 in Vehicle Bracket

Connect Antenna

Note: VX1s equipped with a radio require an external antenna. See Accessories. A VX1 without a radio does not use an antenna.

Antenna Base Antenna Pin

2.4GHz Antenna
900MHz Antenna Figure 22 Connect Antenna
The antenna pin is the same for 900MHz and 2.4GHz spread spectrum radios. Place the antenna base over the antenna pin. Push down and twist clockwise until the antenna is secure. Adjust the antenna angle to improve RF communications with the computer network. Note: Substitution of antennas is not permitted unless authorized by LXE. Use of unauthorized antennas will void the FCC emissions certification of the VX1.

Figure 27 Connect Power Cable to VX1 5. Turn the VX1 on.
External Power Supply, Optional
AC Input Cable DC Output Cable
Figure 28 Optional Power Configuration In North America, this unit is intended for use with a UL Listed ITE power supply with output rated 12-80 V DC, minimum 3.5 A. Outside North America, this unit is intended for use with an IEC certified ITE power supply with output rated 12-80 V DC, minimum 3.5 A. The external power supply may be connected to either a 120V, 60Hz supply or, outside North America, to a 230V, 50Hz supply, using the appropriate detachable cordset. In all cases, connect to a properly grounded source of supply provided with maximum 15 Amp overcurrent protection (10 Amp for 230V circuits). How To: Connect External Power Supply 1. 2. 3. 4. Turn the VX1 off. Connect the detachable cordset provided by LXE to the external power supply (IEC 320 connector). Plug cordset into appropriate, grounded, electrical supply receptacle (AC mains). Connect the 4 pin water tight connector end to the VX1s Power Connector by aligning the connector pins to the power connector; push down on the water tight connector and twist it to fasten securely. Turn the VX1 on.
The LXE-approved AC Power Adapter is only intended for use in a 25C (77F) maximum ambient temperature environment.
Vehicle 12-60VDC Direct Connection
To be installed on NEGATIVE and FLOATING GROUND VEHICLES ONLY.

Caution:

For proper and safe installation, the input power cable must be connected to a fused circuit on the vehicle. This fused circuit requires a 5 Amp maximum time delay (slow blow) high interrupting rating fuse. If the supply connection is made directly to the battery, the fuse should be installed in the positive lead within 5 inches of the battery positive (+) terminal. For installation by trained service personnel only. Risk of ignition or explosion. Explosive gas mixture may be vented from battery. Work only in well ventilated area. Avoid creating arcs and sparks at battery terminals. Do not install metal safety straps to keep the computer from falling if the isolators fail. Only non-conducting straps must be used.

Warning: Warning:

1-To Vehicle Battery 2-To Vehicle Mounted Computer 3-Green 4-Red / White (DC+) 5-Red / Black (DC-) 6-VDC Figure 29 12-60VDC Direct Vehicle Power Connection Cable (Fuse Not Shown) 1-Vehicle Electrical System 2-5 Amp Slow Blow Fuse 3-DC + 4-DC 5-Vehicle Chassis 6-Red / White 7-Red / Black 8-Green Figure 30 12-60VDC Connecting the Power Cable to the Vehicle Note: Correct electrical polarity is required for safe and proper installation. Connecting the cable to the computer with the polarity reversed will cause the computers fuse to be blown. See the following figure titled "Vehicle Connection Wiring Color Codes" for additional wire color-coding specifics.
How To: Connect Vehicle 12-60VDC Direct Connection 1. 2. The computer must be turned off. While observing the fuse requirements specified on the previous page, connect the power cable as close as possible to the actual battery terminals of the vehicle. When available, always connect to unswitched terminals in vehicle fuse panel, after providing proper fusing. IMPORTANT: For uninterrupted power, electrical supply connections should not be made at any point after the ignition switch of the vehicle. 3. Route the cable the shortest way possible. The input cable from the connection to the battery is rated for a maximum temperature of 105C (221F). When routing this cable it should be protected from physical damage and from surfaces which might exceed this temperature. Do not expose the cable to chemicals or oil that may cause the wiring insulation to deteriorate. Note: If the vehicle is equipped with a panel containing Silicon Controlled Rectifiers (SCR's), avoid routing the power cable in close proximity to these devices. Always route the cable so that it does not interfere with safe operation and maintenance of the vehicle. Use proper electrical and mechanical fastening means for terminating the cable. Properly sized "crimp" type electrical terminals are an accepted method of termination. Please select electrical connectors sized for use with 18AWG (1mm2) conductors. Wiring color codes for LXE supplied DC input power cabling: Vehicle Supply +12 - 60VDC (DC +) Return (DC -) Vehicle Chassis (GND) Note: 4. Wire Color Red with White Stripe Red with Black Stripe Green

Always route the cable so that it does not interfere with safe operation and maintenance of the vehicle. Use proper electrical and mechanical fastening means for terminating the cable. Properly sized "crimp" type electrical terminals are an accepted method of termination. Please select electrical connectors sized for use with 18AWG (1mm2) conductors. Wiring color codes for LXE supplied DC input power cabling: Vehicle Supply +12 - 80VDC (DC +) Return (DC -) Chassis (GND) Wire Color Red with White Stripe Red with Black Stripe Green
Figure 34 12-80VDC Vehicle Connection Wiring Color Codes Note: This computer accepts a wide DC input voltage range. Do not connect the computer's input power cable to any other LXE computer or damage to that computer may occur.
Provide mechanical support for the cable by securing it to the vehicle structure at approximately one foot intervals, taking care not to overtighten and pinch conductors or penetrate outer cable jacket. Connect the cable to the computer by aligning the water tight connector pins to the power connector; push down on the connector and twist it to fasten securely. Turn the computer on.
Fuse Replacement for the VX1
The VX1 uses a 125V, 5A time delay (slow blow), high current interrupting rating fuse that is externally accessible and user replaceable. Should it need replacement, replace with same size, rating and type of fuse -- Bussman Type GMC-5 (5x20mm). 3 Fuse Twist in this direction to remove Twist in this direction to insert
Figure 35 Fuse Replacement 1. 2. Turn the VX1 off and disconnect the power cable from the VX1. While holding the VX1 over a level surface, push the fuse cover in and twist it one quarter turn counterclockwise. A flat head screwdriver may be used to twist the fuse cover. Remove the fuse. Discard the fuse and place a new fuse in the holder. Push the fuse in and twist it clockwise one quarter turn. Reconnect the power cable to the VX1.

3. 4. 5. 6.

Operation

Powering On/Off

Connect the VX1 to a power source, either AC or Vehicle. The power (on/off) switch is a toggle switch located on the bottom of the VX1. The switch is sealed by a rubber boot seal. The Status LED or the display, located on the front of the VX1, is lit when the power is on. Note: Always turn the computer off prior to connecting or disconnecting any power source.

Keyboard Entry

Refer to Appendix A - Key Maps for terminal emulation specific keypresses. The keyboard is used to manually input data that is not collected otherwise. Almost any function that a full sized computer keyboard can provide is duplicated on the VX1 keyboard but it may take a few more keystrokes to accomplish a keyed task. Almost every key has two or three different functions. The primary alpha or numeric character is printed on the key. For example, when the 2nd key is first pressed, press the desired second-function key to produce the 2nd character i.e. <2nd+F1> toggles the CAPS lock function. The specific 2nd character is printed on the corresponding key. Please refer to Appendix A - Key Maps for instruction on the specific keypresses to access all keyboard functions.

Scanner Entry

The following section is directed toward a tethered scanner connected to a serial port on the VX1.
Aiming the Barcode Scanner
Aim the scanner away from you, direct it at the barcode and press the trigger to scan. The Scan On LED (or equivalent) turns red to indicate the scanner is on. Adjust the aim so that the thin, red laser beam covers the entire length of the barcode. Some scanners use a laser aiming beam which then spreads into a wide beam when the scanner's Aiming Beam Timer expires. Place the aiming beam in the center of the barcode and hold the scanner steady until the beam spreads and the barcode is decoded. Beeps may be heard as the barcode is decoded. Refer to the barcode scanner user's guide for information on the Aiming Beam Timer and beep sequences, and the TE reference guide for host generated beep sequences. The scan beam must cross every bar and space on the barcode.

Correct Scan

Incorrect Scan Figure 43 Scan Beam

Incorrect Scan

Distance from Label
Large barcodes can be scanned at the maximum distance. Hold the scanner closer to small barcodes (or with bars that are very close together). Note: Do not position the scanner exactly perpendicular to the barcode being scanned. In this position, light can bounce back into the scanners exit window, and possibly prevent a successful decode.

Successful Scan

When the scan is successful, the scanner's good scan indicator illuminates, the scan on indicator is off, and the currently running application may produce a distinctive audible tone.

Unsuccessful Scan

When the scan is unsuccessful, the scan on indicator remains illuminated and the currently running application may produce distinctive audible tones. Check the following: Is the scanner programmed for the barcode being read? Check the barcode for marks or physical damage e.g. ripped label, missing section, etc. Try scanning test symbols of the same code type at different distances and angles.

Press this key V W X Y Z

x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 9
To get this key 0 (alpha) DOT (alpha) 1 (numeric) 2 (numeric) 3 (numeric) 4 (numeric) 5 (numeric) 6 (numeric) 7 (numeric) 8 (numeric) 9 (numeric) 0 (numeric) DOT (numeric) < [ ] > = { } / (numeric) / (alpha) - (numeric) - (alpha) + (numeric) + (alpha) * (numeric) * (alpha) : (colon) ; (semicolon) ? ` _ (underscore) , (comma) (apostrophe) ~ (tilde) \ | !

Shift x

Press this key 0 K DOT
x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x
9 I I D F L N M J H B S A G Q
To get this key @ # $ % ^ & ( )
Press this key W E R T Y U O P
IBM 3270 and TN3270 Terminal Emulator Keypad
Figure 45 IBM 3270 Specific Keypad This keypad is designed to allow the user to enter terminal emulator commands when running LXEs IBM 3270 and TN3270 Terminal Emulation (TE) programs. When running these programs please refer to the following terminal emulation reference guides for equivalent keys and keypress sequences: 3270 DOS TE Reference Guide (Obsolete) 3270 Programmers Reference Guide (Obsolete) TN3270 Terminal Reference Guide
IBM 5250 and TN5250 Terminal Emulator Keypad
Figure 46 IBM 5250 Specific Keypad This keypad is designed to allow the user to enter terminal emulator commands when running LXEs IBM 5250 and TN5250 Terminal Emulation (TE) programs. When running these programs please refer to the following terminal emulation reference guides for equivalent keys and keypress sequences: 5250 DOS TE Reference Guide (Obsolete) 5250 Programmers Reference Guide (Obsolete) TN5250 Terminal Reference Guide
Appendix B Regulatory Notices and Safety Information
FCC Information: This device complies with FCC Rules, part 15. Operation is subject to the following conditions: 1. 2. This device may not cause harmful interference and This device must accept any interference that may be received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Warning: Changes or modifications to this device not expressly approved by LXE, Inc., could void the users authority to operate this equipment. EMC Directive Requirements: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Industry Canada: This Class A digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareil numrique de la classe A respecte toutes les exigences du Rglement sur le matriel brouiller du Canada. Le present appareil numrique nemet pas de bruits radiolectriques dpassant les limites applicables aux appareils numeriques de le Classe A prscrites dans le Reglement sur le brouillage radiolectrique dits par le ministere des Communications du Canada. Notice: The long term characteristics or the possible physiological effects of radio frequency electromagnetic fields have not been investigated by UL. RF Safety Notice: Caution: This device is intended to transmit RF energy. For protection against RF exposure to humans and in accordance with FCC rules and Industry Canada rules, this transmitter should be installed such that a minimum separation distance of at least 20 cm (7.8 in.) is maintained between the antenna and the general population. This device is not to be co-located with other transmitters. Important: This symbol is placed on the product to remind users to dispose of Waste Electrical and Electronic Equipment (WEEE) appropriately, per Directive 2002-96-EC. In most areas, this product can be recycled, reclaimed and re-used when properly discarded. Do not discard labeled units with trash. For information about proper disposal, contact LXE through your local sales representative, or visit www lxe com.

Regulatory Notices and Safety information
R&TTE Directive Requirements
Information to User A label on the exterior of the device should resemble one of the labels shown below (the label contains the LXE part number of the installed radio card). The labels shown below and affixed to the device, identify where the device may be used and where its use is restricted. Use of a device is prohibited in countries not listed below or otherwise identified by the label.
Permitted for use in: Austria, Belgium, Denmark, Finland, Germany, Greece, Hungary, Iceland, Italy, Ireland, Liechtenstein, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, and the United Kingdom
Permitted for use in France

Approvals

Product VX1 EMI / EMC Standards EMI / EMC Standards: FCC Part 15 Subpart B, Class A EN 55022 : 1998 Class A EN 55024 : 1998 Safety Standards EN 60950-1 : 1992 + Amendments A1.A4 UL 1950 CSA C22.2 No. 950 IEC950 CB Scheme RF Standards FCC Part 15, Subpart C FCC Part 2 ETS ETS IC-RSS 210 IC-RSS 102 FCC Part 15, Subpart C FCC Part 2 ETS ETS IC-RSS 139 IC-RSS 102 FCC Part 15, Subpart C IC-RSS 210 FCC Part 15, Subpart C FCC Part 2 EN EN IC-RSS 139 IC-RSS 102 FCC Part 15, Subpart C FCC Part 2 EN EN IC-RSS 139 IC-RSS 102 Notes Unlicensed Operation Unlicensed Operation Requires License for Outdoor Use
Transceiver 480824-3300 (LXE Part No.) LXE 6400 System 2.4GHz Type II PCMCIA Card (Obsolete)
480628-4096 (LXE Part No.) LXE 6500 System 2.4GHz Type II PCMCIA Card (Obsolete)
Unlicensed Operation Unlicensed Operation Requires License for Outdoor Use
4810P3S01 (LXE Part No.) [Obsolete] LXE 6200 System 900MHz Type III PCMCIA Card 6526 (LXE Model No.) 6726 (LXE Model No.) (Obsolete)
Unlicensed Operation Unlicensed Operation Unlicensed Operation Unlicensed Operation Requires License for Outdoor Use Unlicensed Operation Unlicensed Operation Requires License for Outdoor Use
6816 (LXE Model No.) 2.4GHz Type II PCMCIA Card
Regulatory Notices and Safety Information
LXE Transceiver 480628-4096 Declaration of Conformity
DECLARATION OF CONFORMITY
according to Directives: 1999/5/EC 93/68/EEC Type of Equipment: Brand Name or Trademark: Type Designation: Manufacturer: Address: Year of Manufacturer: Radio Equipment and Telecommunications Terminal Equipment and the mutual recognition of their conformity CE Marking Directive Direct Sequence 2.4 GHz Wireless LAN Card LXE 480628-4096 LXE Inc. 125 Technology Parkway Norcross, GA 30092-2993 USA 2000

The following harmonized European Standards, technical specifications, or other normative documents have been applied: EMI / EMC Standards: EN 55022 : 1995 Limits and methods of measurement of radio disturbance characteristics of information technology equipment ETS : 1997 EN 61000-4-2 : 1995 EN 61000-4-3 : 1997 EN 61000-4-6 : 1996 Radio Frequency Standards: ETS : 1996 Electromagnetic compatibility - Generic immunity standard, Part 1: Residential, commercial and light industrial Electrostatic discharge immunity test Radiated radio frequency electromagnetic field immunity test RF conducted immunity test Radio Equipment and Systems (RES); Wideband transmission systems; Technical characteristics and test conditions for data transmission equipment operating in the 2,4 GHz ISM band and using spread spectrum modulation techniques Safety Standards: IEC 950-2: 1991 + Amendments A1.A4 Safety of information technology equipment, including electrical business equipment
We, LXE Inc., declare that the equipment specified above complies with all Essential Health and Safety Requirements of the above Directives and Standards, as amended. Place: Date of issue: LXE Inc., Norcross GA USA 1 March, 2000 Signed: R. Sam Wismer, RF Approvals Engineer
LXE Inc. 125 Technology Parkway Norcross, GA 30092-2993 USA ph. 770/447-4224 fax 770/447-6928
LXE Transceiver 480824-3300 Declaration of Conformity
according to Directives: 1999/5/EC 93/68/EEC Type of Equipment: Brand Name or Trademark: Type Designation: Manufacturer: Address: Year of Manufacturer: Radio Equipment and Telecommunications Terminal Equipment and the mutual recognition of their conformity CE Marking Directive Frequency Hopping 2.4 GHz Wireless LAN Card LXE 480824-3300 LXE Inc. 125 Technology Parkway Norcross, GA 30092-2993 USA 2000
We, LXE Inc., declare that the equipment specified above complies with all Essential Health and Safety Requirements of the above Directives and Standards, as amended. Place: LXE Inc., Norcross GA USA Signed: R. Sam Wismer, Lead Approvals Engineer
LXE Transceiver LXE 6526 Declaration of Conformity
according to Directives: 1999/5/EC 93/68/EEC Type of Equipment: Brand Name or Trademark: Type Designation: Manufacturer: Address: Year of Manufacturer: Radio Equipment and Telecommunications Terminal Equipment and the mutual recognition of their conformity CE Marking Directive Direct Sequence 2.4 GHz Wireless LAN Card LXE LXE 6526 LXE Inc. 125 Technology Parkway Norcross, GA 30092-2993 USA 2001
The following harmonized European Standards, technical specifications, or other normative documents have been applied: EMI / EMC Standards: EN 55022 : 1995 Limits and methods of measurement of radio disturbance characteristics of information technology equipment EN : 1997 EN 61000-4-2 : 1995 EN 61000-4-3 : 1997 EN 61000-4-6 : 1996 Radio Frequency Standards: EN : 1996 Electromagnetic compatibility - Generic immunity standard, Part 1: Residential, commercial and light industrial Electrostatic discharge immunity test Radiated radio frequency electromagnetic field immunity test RF conducted immunity test Radio Equipment and Systems (RES); Wideband transmission systems; Technical characteristics and test conditions for data transmission equipment operating in the 2,4 GHz ISM band and using spread spectrum modulation techniques Safety Standards: EN 60950-2: 1991 + Amendments A1.A4 Safety of information technology equipment, including electrical business equipment

We, LXE Inc., declare that the equipment specified above complies with all Essential Health and Safety Requirements of the above Directives and Standards, as amended. Place: Date of issue: LXE Inc., Norcross GA USA 30 March, 2001 Signed: R. Sam Wismer, RF Approvals Engineer
LXE Transceiver LXE 6726 Declaration of Conformity
DECLARATION OF CONFORMITY according to Directives: 1999/5/EC 93/68/EEC Type of Equipment: Brand Name or Trademark: Type Designation: Manufacturer: Address: Year of Manufacturer: Radio Equipment and Telecommunications Terminal Equipment and the mutual recognition of their conformity CE Marking Directive Direct Sequence 2.4 GHz Wireless LAN Card LXE LXE 6726 LXE Inc. 125 Technology Parkway Norcross, GA 30092-2993 USA 2001
The following harmonized European Standards, technical specifications, or other normative documents have been applied: EMC: EN 301 489-1: 07-2000 Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 17: Specific conditions for Wideband data and HIPERLAN equipment Radio Equipment and Systems (RES); Wideband transmission systems; Technical characteristics and test conditions for data transmission equipment operating in the 2,4 GHz ISM band and using spread spectrum modulation techniques Safety of information technology equipment, including electrical business equipment

EN 301 489-17 07-2000

Radio: EN 300 328-1 and -2: 2000-7
Safety: EN 60950-2: 1992 + A1.A4
We, LXE Inc., declare that the equipment specified above complies with all Essential Health and Safety Requirements of the above Directives and Standards, as amended. Place Date of issue LXE Inc., Norcross GA USA 24 June 2004 C. Binnom Jr. RF Approvals Engineer LXE Inc. 125 Technology Parkway Norcross, GA 30092-2993 USA ph. 770/447-4224 fax 770/447-6928
Annex to DoC for LXE 6726
With regard to the use of external antennas The LXE 6726 can be equipped with external antennas. The antennas listed have been evaluated with the LXE 6726 pursuant to ETSI EN 300 328, and therefore meet the definition of dedicated antenna per ERC/REC 70-03 Appendix 1 Table 3; thus the requirement set forth in ERC/REC 70-03 , Annex 3 are met by the LXE model 6726 transceiver. Dedicated Antennas for use with LXE 6726 LXE P/N 153180-0001 155522-0001 155814-0001 157368-0001 157399-0001 99004-0027 DAC2450CT1 (Toko P/N) Antenna Gain 0 dBi 0 dBi 0 dBi 0 dBi 0 dBi 0 dBi 2.15 dBi Radio Power Level 17 dBm 17 dBm 17 dBm 17 dBm 17 dBm 17 dBm 17 dBm Antenna Description Omni, for LXE VX-series computers Omni, for LXE MX1-series computers Patch, for LXE MX1-series computers Patch, for LXE MX3-series computers Omni, for LXE MX5-series computers 3 dB Omni, for LXE model 2325 computer Omni, for LXE MX2-series computers

153179-0001 153325-0001 480424-0400 153599-0001 153600-0001 480424-3404 155846-0001
0 dBi 0 dBi 0 dBi 3 dBi 3 dBi 3 dBi 3 dBi
17 dBm 17 dBm 17 dBm 17 dBm 17 dBm 17 dBm 17 dBm
Omni, Access Point Antenna Omni, Access Point Antenna Omni, Access Point Antenna Omni, Access Point Antenna Omni, Access Point Antenna Omni, Access Point Antenna Spire Access Point Antenna
155845-0001 155311-0001 480424-3411 480424-3402 481246-2400 480424-1702 480424-0411 480429-2703 480429-0411 460601-3020 460602-3020 480429-0415
6 dBi 6 dBi 6 dBi 6 dBi 6 dBi 6 dBi 9 dBi 12 dBi 12 dBi 15 dBi 15 dBi 15 dBi
13 dBm 13 dBm 13 dBm 13 dBm 13 dBm 13 dBm 7 dBm 7 dBm 7 dBm 3 dBm 3 dBm 3 dBm
Spire Access Point Antenna Patch, Access Point Antenna Patch, Access Point Antenna Patch, Access Point Antenna Patch, Access Point Antenna 180 Directional, Access Point Antenna Omni, Access Point Antenna 90 Directional, Access Point Antenna Omni, Access Point Antenna YAGI, Access Point Antenna YAGI, Access Point Antenna Omni, Access Point Antenna
C. Binnom Jr. RF Approvals Engineer 24 June 2004 LXE Inc. 125 Technology Parkway Norcross, GA 30092-2993 USA ph. 770/447-4224 fax 770/447-6928
LXE Transceiver LXE 6816 Declaration of Conformity
DECLARATION OF CONFORMITY according to: the R&TTE Directive; The EMC Directive; The Low Voltage Directive; and the Marking Directive; Type of Equipment: Brand Name or Trademark: Type Designation: Manufacturer: Address: 99/5/EEC 89/336/EEC 73/23/EEC 93/68/EEC DSSS 2.4GHz WLAN Radio Card LXE 6816 LXE Inc. 125 Technology Parkway Norcross, GA 30092 USA
The following harmonized European Norms have been applied: EMC Standards: EN 301 489-1: 07-2000 Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 17: Specific conditions for Wideband data and HIPERLAN equipment Limits and methods of measurement of radio disturbance characteristics of information technology equipment Radio Equipment and Systems (RES); Wideband transmission systems; Technical characteristics and test conditions for data transmission equipment operating in the 2.4 GHz ISM band and using spread spectrum modulation techniques Safety of information technology equipment, including electrical business equipment