CHANGE SIGN KEY: Changes the algebraic sign of a number (i.e., positive to negative or negative to positive). RECALL AND CLEAR MEMORY KEY RECALL MEMORY KEY
TECLA DE CAMBIO DE SIGNO: Cambia el signo algebraico de un nmero (es decir, de positivo a negativo o de negativo a positivo). TECLA DE TOTAL Y BORRADO DE MEMORIA TECLA DE TOTAL PARCIAL EN MEMORIA TECLA DE INCLUSIN DE IMPUESTOS TECLA DE ANTES DE IMPUESTOS TECLA DE TOTAL GLOBAL TECLA DE INTRODUCCIN DEL PRECIO DE COSTE: Pulse esta tecla para introducir el precio de coste. TECLA DE INTRODUCCIN DEL PRECIO DE VENTA: Pulse esta tecla para introducir el precio de venta. TECLA DE INTRODUCCIN DEL MARGEN: Pulse esta tecla para introducir el margen. SMBOLOS DE LA EXHIBICIN: M E : Aparece cuando un nmero se almacena en la memoria. : Aparece cuando el nmero es negativo. : Aparece cuando un nmero est en la memoria de total global. : Aparece cuando se detecta un error o se supera la capacidad.
ELECTRONIC PRINTING CALCULATOR CALCULADORA IMPRESORA ELECTRNICA

EL-1801P

TAX-INCLUDING KEY PRE-TAX KEY GRAND TOTAL KEY
OPERATION MANUAL MANUAL DE MANEJO
COST PRICE ENTRY KEY: Press this key to enter the cost price. SELLING PRICE ENTRY KEY: Press this key to enter the selling price. MARGIN ENTRY KEY: Press this key to enter the margin.
WARNING FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the users authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
DISPLAY SYMBOLS: M E : Appears when a number is in the memory. : Appears when a number is negative. : Appears when a number is in the grand total memory. : Appears when an overflow or other error is detected.

SHARP CORPORATION

OPERATIONAL NOTES
To insure trouble-free operation of your SHARP calculator, we recommend the following: 1. The calculator should be kept in areas free from extreme temperature changes, moisture, and dust. 2. A soft, dry cloth should be used to clean the calculator. Do not use solvents or a wet cloth. 3. Since this product is not waterproof, do not use it or store it where fluids, for example water, can splash onto it. Raindrops, water spray, juice, coffee, steam, perspiration, etc. will also cause malfunction. 4. If service should be required, use only a SHARP servicing dealer, a SHARP approved service facility or SHARP repair service. 5. If you pull out the power cord to cut electricity completely, the presently stored tax rate will be cleared. 6. Do not wind the AC cord around the body or otherwise forcibly bend or twist it.
PRINTED IN CHINA / IMPRESO EN CHINA 02KT(TINSZ0584EHZZ)

INK ROLLER REPLACEMENT

If printing is blurry even when the ink roller is in the proper position, replace the roller. Ink roller: Type EA-772R WARNING APPLYING INK TO WORN INK ROLLER OR USE OF UNAPPROVED INK ROLLER MAY CAUSE SERIOUS DAMAGE TO PRINTER. 1) Set the power switch to OFF. 2) Remove the printer cover. (Fig. 1) 3) Hold the top of the ink roller and remove the roller by pulling it toward you and then upward. (Fig. 2) 4) Install the new ink roller in the correct position. Make sure that the roller is securely in place. (Fig. 3) 5) Put back the printer cover.
CAMBIO DEL RODILLO ENTINTADOR
Si la impresin queda borrosa aunque est bien colocado el rodillo entintador, reemplace el rodillo. Rodillo entintador: Tipo EA-772R ADVERTENCIA ECHANDO TINTA EN UN RODILLO ENTINTADOR ROTO O USANDO UN RODILLO ENTINTADOR NO AUTORIZADO P U E D E C A U S A R D E T E R I O R O S G R AV E S E N L A IMPRESORA. 1) Poner el interruptor de corriente en OFF. 2) Sacar la tapa de la impresora. (Fig. 1) 3) Sujete la parte superior del rodillo entintador y extraiga el rodillo tirando de l hacia usted y hacia arriba. (Fig. 2) 4) Instalar el nuevo rodillo entintador en la posicin correcta. Cerciorarse de que el rodillo est firmemente colocado en su sitio. (Fig. 3) 5) Poner de nuevo en su lugar la tapa de la impresora.

Operation

Display

250 800. 40. 840.

250. 50.
ADDITION AND SUBTRACTION WITH ADD MODE SUMA Y RESTA CON MODO DE SUMA
12.45 + 16.24 + 19.35 5.21 =
: Entries in the order of : Las entradas en el orden de 500 vlidas.

1935 521

12.45 28.69 48.04 42.83 42.83
12.45 + 16.24 + 19.35 + 5.21 . 002 42.83
EXAMPLE 2: Perform two calculations using $840 and $525, both of which already include tax. Calculate the tax on the total and the total without tax. (tax rate: 5%) EJEMPLO 2: Realice dos clculos utilizando $800 y $525, los cuales ya incluyen impuesto. Calcule et impuesto sobre el total y el total sin impuesto. (tasa de impuestos: 5%)
, , or The entered value (enter value, then press ) will be kept in the buffer; the re-entry will not be necessary when recalculating. The buffer contents will be cleared upon new entry, or when the power switch is turned off/on, or when E is displayed. El valor introducido (incorpore el valor, despus , o ) se mantendr en la memoria intermedia; el valor reintroducido no indica que volver a realizarse necesariamente el clculo. El contenido de la memoria intermedia se borrar con una entrada nueva, cuando el interruptor de la alimentacin se desactive/active o cuando se visualice E.
was not used in the entries. *1 : *1 : La no ha sido usada en los registros.

840 525

840. 1,365.
MIXED CALCULATIONS / CLCULOS MIXTOS
A. + 12 = 5. 10. 10. 22. 22.

OFF P PIC

B. (10 + 2) 5 = 5 10. 12. 12. 60. 10. 2. 12. 5. 60. + + =

1,300.

840. + 525. + ,365. 1. 65. 1,300.
5. 2. = 10. 10. + 12. + 002. 22.

CONSTANT / CONSTANTES

A. 62.35 11.11 = 62.35 22.22 = 62.35 11.11 = 692. 7085 22.22 = 1,385.417
In case of abnormal conditions When this unit is exposed to strong RF noise and/or extreme physical shock during the operation, or when the power cord is plugged into the AC outlet, the unit may start functioning abnormally which, in some rare occasions, all keys - including key - cease to respond. the power key and the If such abnormal conditions are observed, unplug the AC cord from the socket. Keep the unit unplugged for about 5 seconds, reconnect the AC plug, then turn on the power.
B. 11.11 77.77 = 22.22 77.77 = 11.11 77.77 11.11 0.14285714285 22.22 0.28571428571

62.35 11.11

62.35 692.7085
11.11 77.77 = 0.14285714285 22.22 = 0.28571428571

22.22 1,385.417

En caso de condiciones anormales Si expone esta unidad a ruido de RF intenso y/o a golpes fuertes durante la operacin, o cuando enchufe el cable de alimentacin en un tomacorriente de CA, la unidad puede comenzar a funcionar de forma anormal, por lo que, en algunos casos raros, todas las teclas incluyendo la de alimentacin y la tecla pueden no ofrecer respuesta. Si experimenta estas condiciones anormales, desenchufe el cable de alimentacin de CA del tomacorriente. Deje la unidad desenchufada durante unos 5 segundos, vuelva a enchufar el cable de alimentacin de CA, y despus conecte la alimentacin.

PERCENT / PORCENTAJES

A. 100 25% = 100. 25.00 100. 25. % 25.00
B. = (%) 123. 8.99 123. 1,368. % 8.99
Caution! The socket outlet shall be installed near the equipment and shall be easily accessible. Aviso! El tomacorriente debe estar instalado cerca del equipo y debe quedar bien accesible.

LIMITED WARRANTY

SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the Product), when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below. This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth below nor to any Product the exterior of which has been damaged or defaced, which has been subjected to improper voltage or other misuse, abnormal service or handling, or which has been altered or modified in design or construction. In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth below and provide proof of purchase to the servicer. The limited warranty described herein is in addition to whatever implied warranties may be granted to purchasers by law. ALL IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE ARE LIMITED TO THE PERIOD(S) FROM THE DATE OF PURCHASE SET FORTH BELOW. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those described herein, or to extend the duration of any warranties beyond the time period described herein on behalf of Sharp. The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and exclusive remedy available to the purchaser. Correction of defects, in the manner and for the period of time described herein, shall constitute complete fulfillment of all liabilities and responsibilities of Sharp to the purchaser with respect to the Product, and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise. In no event shall Sharp be liable, or in any way responsible, for any damages or defects in the Product which were caused by repairs or attempted repairs performed by anyone other than an authorized servicer. Nor shall Sharp be liable or in any way responsible for any incidental or consequential economic or property damage. Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion may not apply to you. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE. Your Product : Warranty Period for this Product : Electronic Calculator Six (6) months parts and labor from date of purchase.

ITEM COUNT CALCULATION CLCULO DE CUENTA DE ARTCULOS
Bill No. N de factura 5 Total Number of bills Cantidad de facturas 1 (a) Amount Importe $100.55 $200.00 $200.00 $400.55 $500.65 (b)
GRAND TOTAL / TOTAL GLOBAL
100 + 200 + 300 = +) 300 + 400 + 500 = Grand total / Total global

www.sharpusa.com

For your convenience, Genuine Sharp Supplies. Accessories, and additional Sharp Products can be purchased from the Authorized Sharp Reseller where you purchased your product or on-line at:
100. 300. 600. 600. 300. 700. 1,200. 1,200. 1,800.
100. 200. 300. 600. 300. 400. 500. 1,200.

+ + + + + + + +

www.sharpplace.com
Additional Items Excluded Any consumable items such as paper, maintenance cartridge, ink from Warranty Coverage : cartridges supplied with the Product or to any equipment or any hardware, software, firmware, fluorescent lamp, power cords, covers, rubber parts, or peripherals other than the Product. Where to Obtain Service : At a Sharp Authorized Servicer located in the United States. To find out the location of the nearest Sharp Authorized Servicer, call Sharp toll free at 1-800-BE-SHARP. What to do to Obtain Service : Ship (prepaid) or carry in your Product to a Sharp Authorized Servicer. Be sure to have proof of purchase available. If you ship or mail the Product, be sure it is packaged carefully. TO OBTAIN SUPPLY, ACCESSORY OR PRODUCT INFORMATION, CALL 1-800-BE-SHARP.

100.400.55 500.65

100.55 300.55 500.55 901.10 1,401.75 1,401.75
100.55 + 200.00 + 200.00 + 400.55 + 500.65 + 005. 1,401.75

1,800.

(a) (b)

EL-1801P(U1U)-2

EL-1801PIII

OPERATION MANUAL MANUAL DE MANEJO
0: Presets the number of decimal places in the answer. F: The answer is displayed in the floating decimal system. A: The decimal point in addition and subtraction entries is automatically positioned to the 2nd digit from the lowest digit of entry number. Use of the add mode permits addition , and and subtraction of numbers without entry of the decimal point. Use of will automatically override the add mode and decimally correct answers will be printed. CLOCK / CALENDAR KEY: Each time this key is pressed, the mode switches. Calculation mode Date display mode Clock display mode Calculation mode Use this key also to adjust date and time (see GRAND TOTAL / RATE SETTING MODE SELECTOR). PAPER FEED KEY LAST DIGIT CORRECTION KEY
WARNING FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the users authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

SHARP CORPORATION

PRINTED IN CHINA / IMPRESO EN CHINA 04ET(TINSE0745EH02)
NON-ADD / SUBTOTAL KEY: Non-add When this key is pressed right after an entry of a number in the Print mode, the entry is printed on the left-hand side with the symbol #. This key is used to print out numbers not subjects to calculation such as code, date, etc. Subtotal Used to get subtotal(s) of additions and/or subtractions. When pressed or key, the subtotal is printed with the symbol and the following the calculation may be continued. By pressing this key even in the Non-print mode, the displayed number is printed without any symbol. When the POWER SWITCH; PRINT / ITEM COUNT MODE SELECTOR is set , P or PIC position, and Date or Clock is displayed, press this key to print the displayed contents, including # symbol, from the left side of the paper roll. Example: Date printing #2004 (when the date is September 15, 2004) Clock printing # (when the time is 10:30 a.m.) #- - - - - - - - - - - (when the time is 6:25 p.m.) When the Date / Clock printing is complete, the Calculation mode is restored.

CLEAR / CLEAR ENTRY KEY Press this key twice, followed by TOTAL KEY EQUAL KEY
, to print the set tax rate.
CHANGE SIGN KEY: Changes the algebraic sign of a number (i.e., positive to negative or negative to positive). RECALL AND CLEAR MEMORY KEY RECALL MEMORY KEY TAX-INCLUDING KEY PRE-TAX KEY AVERAGE KEY: Used to calculate the average. GRAND TOTAL KEY COST PRICE ENTRY KEY: Press this key to enter the cost price. SELLING PRICE ENTRY KEY: Press this key to enter the selling price. MARGIN ENTRY KEY: Press this key to enter the margin. DISPLAY SYMBOLS:
SHARP will not be liable nor responsible for any incidental or consequential economic or property damage caused by misuse and/or malfunctions of this product and its peripherals, unless such liability is acknowledged by law.
SHARP no ser responsable de ningn dao imprevisto o resultante, en lo econmico o en propiedades, debido al mal uso de este producto y sus perifricos, a menos que tal responsabilidad sea reconocida por la ley.
USING THE CALCULATOR FOR THE FIRST TIME
First, pull out the insulation sheet for the memory protection battery (installed for retaining the date/time/tax rate information). Reset the calculator to initialize the unit's state, then adjust the date and time before using the calculator. Removing the insulation sheet, and resetting 1. Pull out the insulation sheet for the memory protection battery.
UTILIZACIN DE LA CALCULADORA POR PRIMERA VEZ
En primer lugar, tire de la lmina aislante para la pila de proteccin de la memoria (instalada para conservar la informacin sobre la fecha/hora/tasa de impuestos). Reponga la calculadora para inicializar el estado de la unidad, y despus ajuste la fecha y la hora antes de utilizarla. Extraccin de la lmina aislante, y reposicin 1. Tire de la lmina aislante para la pila de proteccin de la memoria.
M : Appears when a number is in the memory. E : Appears when a number is negative. : Appears when a number is in the grand total memory. : Appears when an overflow or other error is detected.

INK ROLLER REPLACEMENT

(consulteSELECTOR DEL MODO DE TOTAL GLOBAL / FIJACIN DE TASA) * Cuando finalice el ajuste, el reloj comenzar a funcionar a las 3:38:00 p.m.

OPERATING CONTROLS

OFF P PIC ON
CONTROLES DE FUNCIONAMIENTO

Fig. 1

Fig. 2

Fig. 3

POWER SWITCH; PRINT / ITEM COUNT MODE SELECTOR:
INTERRUPTOR DE LA ALIMENTACIN; SELECTOR DEL MODO DE IMPRESIN / MODO PARA CONTAR ARTCULOS:
OFF: Power OFF : Power ON. Set to the non print mode. P: Power ON. Set to the print mode. PIC: Power ON. Set to the print and item count mode. is pressed, 1 is added to the item 1) For addition or subtraction, each time is pressed, 1 is subtracted. counter, and each time The count is printed when the calculated result is obtained. , clears the counter. Pressing of 2) When the grand total/rate setting mode selector is in the ON position (GT), the counter will count the number of times that the calculation results have been key. stored in the grand total memory. To print and clear the count, press the key has 3) The memory item counter will count the number of times that the been pressed in the addition. key is used in the subtraction, 1 will be subtracted from Note: Each time the the count. The count is printed when the memory is recalled. key clears the counter. Pressing of the Note: The counter has a maximum capacity of 3 digits (up to 999). If the count exceeds the maximum, the counter will recount from zero.
OFF: Apagado (OFF) : Encendido (ON). Fija el modo de no impresin. P: Encendido (ON). Fija el modo de impresin. PIC: Encendido (ON). Fija el modo de impresin y de cuenta de artculos. se aadir 1 al contador de 1) En las sumas o restas, cada vez que se pulse se restar 1. artculos, y cada vez que se pulse La cuenta queda impresa cuando se obtiene el resultado calculado. , se borra el contenido del contador. Al pulsar 2) Cuando est activado el selector del modo de total global/fijacin de tipos (posicin GT), el contador contar el nmero de veces que se han almacenado los resultados de clculo en la memoria del total global. Para imprimir y borrar la. cuenta, apretar la tecla 3) El contador de artculos en memoria contar el nmero de veces que la tecla ha sido apretada en la suma. en la resta, 1 ser restado de la cuenta. Notas: Cada vez que se use la tecla La cuenta queda impresa al llamarse la memoria. se borra el contador. Apretando la tecla Nota: El contador tiene una capacidad de un mximo de 3 dgitos (hasta 999). Si la cuenta excede el mximo, el contador vuelve a contar partiendo de cero.
Cleaning the printing mechanism If the print becomes dull after long time usage, clean the printing wheel according to the following procedures: 1) Remove the printer cover and the ink roller. 2) Install the paper roll and feed it until it comes out of the front of the printing mechanism. 3) Put a small brush (like a tooth brush) lightly to the printing wheel and clean it by pressing. 4) Put back the ink roller and the printer cover. Note: Do not rotate the printing mechanism manually, this may damage the printer.

GT: Grand Total : Neutral RATE SET: To set the date, time, and tax rate, set this switch at the RATE SET position. Date: to complete the entry. Enter in the order of month, day and year, then press Use to separate month, day, and year. When is pressed, the number entered is evaluated and displayed as date if the value is within the following range; Error is displayed otherwise, and the previously set date is restored. Month: 1 - 12; day: 1 - 31; Year: 2000 - 2099 (in 4 digits) or 00 - 99 (in 2 digits) Time: to complete the entry. Enter in the order of hour, minutes, then press (There is no entry available for the seconds value. The clock starts at zero second.) If the hour/minute digit is less than 10, it is not necessary to enter the first digit 0. to separate hour and minute values. Use is pressed, the number entered is evaluated and displayed as time if the When value is within the following range; Error is displayed otherwise, and the previously set time is restored. Hour: 0 - 23 (24-hour system for the hour entry), Minute: 0 - 59
GT: Total global : Neutra RATE SET: Para ajustar la fecha, la hora, y la tasa de impuestos, ponga este selector en la posicin RATE SET. Fecha: para finalizar la Introduzca, por este orden, el mes, el da, y el ao, y despus pulse introduccin. para separar el mes, el da, y el ao. Utilice , el nmero introducido se evaluar y visualizar como fecha si el Cuando pulse valor introducido est dentro del margen; de lo contrario se visualizar Error, y se restablecer la fecha preestablecida. Mes: 1 - 12; da: 1 - 31; ao: 2000 - 2099 (introduzca 4 dgitos) o 00 - 99 (introduzca 2 dgitos) Hora: para completar la Introduzca, por este orden, la hora y los minutos, y despus pulse introduccin. (No es posible introducir los segundos. El reloj comenzar a funcionar a partir de cero segundos.) Si los dgitos de la hora/minutos son inferiores a 10, no ser necesario introducir el primer dgito 0. para separar los valores de la hora y los minutos. Utilice , el nmero introducido se evaluar y visualizar como hora si el Cuando pulse valor est dentro de la gama; en caso contrario se visualizar Error, y se restablecer la hora previamente ajustada. Hora: 0 - 23 (sistema de 24 horas para la introduccin de la hora), Minutos: 0 - 59

ERRORS

There are several situations which will cause an overflow or an error condition. When this occurs, E will be displayed. The contents of the memory at the time of the error are retained. If an 0E is displayed at the time of the error, will be printed in red and must be used to clear the calculator. Also, in rare cases, printing may stop midway and the indication E appear on the display. This is not a malfunction but is caused when the calculator is exposed to strong electromagnetic noise or static electricity from an external source. Should this occur, press key and then repeat the calculation from the beginning. the Error conditions: 1. When the integer portion of an answer exceeds 12 digits. 2. When the integer portion of the contents of the memory or grand total memory exceeds ) 12 digits. (Ex. 0 ) 3. When any number is divided by zero. (Ex. 5

MEMORY / MEMORIA

= +) = ) = Total *3
COST / SELL / MARGIN CALCULATION CLCULO DE COSTES / VENTAS / MRGENES
EXAMPLE 1: Determine the cost price for 30% margin when the selling price is set at $500. Selling Price Margin Cost price EJEMPLO 1: Determine el precio de coste para un margen del 30% cuando el precio de venta es de 500 euros. precio de venta margen precio de coste F63210A 500. 30. % 350 C 350. : Entries in the order of are also valid. 500 tambin son vlidas. : Las introducciones en el orden de 30

SPECIFICATIONS

Operating capacity: 12 digits Power supply: Operating: AC: 120V, 60Hz Memory backup: 3V. (DC) (Lithium battery CR2032 1) Memory Protection Battery lifespan: About 2,500 hours (While at 25C(77F), and the power plug is not connected to the socket.) CLOCK SECTION Accuracy: Within 60 seconds per month average (at 25C(77F)) Items to be displayed: month, day, year, hour, minute, second, a.m. A, p.m. P Items to be printed: month, day, year, hour, minute, a.m. , p.m. Time system: 12-hour PRINTING SECTION Printer: Mechanical printer Printing speed: Approx. 2.1 lines/sec. (At temperature 25C (77F), when 7419 + is printed. The printing speed will vary with the number of rows and the figure types to be printed.) Printing paper: 57 mm(2-1/4") - 58 mm(2-9/32") wide 80 mm(3-5/32") in diameter (max.) Operating temperature: 0C 40C (32F 104F) Power consumption: 66 mA Dimensions: 193 mm (W) 255 mm (D) 60.5 mm (H) (7-19/32" (W) 10-1/32" (D) 2-3/8" (H)) Weight: Approx. 1.02 kg (2.25 lb.) (with battery) Accessories: 1 lithium battery(installed), 1 battery replacement date label (attached on the unit's back body), 1 paper roll, 1 ink roller (installed), and operation manual WARNING THE VOLTAGE USED MUST BE THE SAME AS SPECIFIED ON THIS CALCULATOR. USING THIS CALCULATOR WITH A HIGHER VOLTAGE THAN THAT WHICH IS SPECIFIED IS DANGEROUS AND MAY RESULT IN A FIRE OR OTHER TYPE OF ACCIDENT CAUSING DAMAGE. WE ARE NOT RESPONSIBLE FOR ANY DAMAGE RESULTING FROM USE OF THIS CALCULATOR WITH A VOLTAGE OTHER THAN THAT WHICH IS SPECIFIED.

If / Si el

Monday / Lunes.. Tuesday / Martes.. Wednesday / Mircoles. Thursday / Jueves. Friday / Viernes..
Total Sales $656.00 for 5 days El total de ventas de los 5 das = $656,00 Then Average Sales = $131.20 / Por lo tanto: Promedio de las ventas = $131,20

RATE ON OFF P PIC GT SET

123.15 241.15 372.73 497.75 656.00

65600

+ + + + +

LIMITED WARRANTY

SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the Product), when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below. This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth below nor to any Product the exterior of which has been damaged or defaced, which has been subjected to improper voltage or other misuse, abnormal service or handling, or which has been altered or modified in design or construction. In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth below and provide proof of purchase to the servicer. The limited warranty described herein is in addition to whatever implied warranties may be granted to purchasers by law. ALL IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE ARE LIMITED TO THE PERIOD(S) FROM THE DATE OF PURCHASE SET FORTH BELOW. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those described herein, or to extend the duration of any warranties beyond the time period described herein on behalf of Sharp. The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and exclusive remedy available to the purchaser. Correction of defects, in the manner and for the period of time described herein, shall constitute complete fulfillment of all liabilities and responsibilities of Sharp to the purchaser with respect to the Product, and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise. In no event shall Sharp be liable, or in any way responsible, for any damages or defects in the Product which were caused by repairs or attempted repairs performed by anyone other than an authorized servicer. Nor shall Sharp be liable or in any way responsible for any incidental or consequential economic or property damage. Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion may not apply to you. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE. Your Product : Warranty Period for this Product : Additional Items Excluded from Warranty Coverage : Electronic Calculator Six (6) months parts and labor from date of purchase.

13120 G 131.20

PRINTING DATE AND TIME IMPRESIN DE LA FECHA Y LA HORA
EXAMPLE: When on October 20, 2005, 1:52:00 p.m. EJEMPLO: En el 20 de octubre de 2005, a las 1:52:00 p.m. *1 10-20-2005. 0. 1-P. 0.
ADDITION AND SUBTRACTION WITH ADD MODE SUMA Y RESTA CON MODO DE SUMA
12.45 + 16.24 + 19.35 5.21 = *2 #10202005 12.45 28.69 48.04 42.83
#152 - - - - - - - - - - - 42.83 *2 : *2 : La was not used in the entries. no ha sido usada en las introducciones.

002 4283

+ + +
Caution! The socket outlet shall be installed near the equipment and shall be easily accessible. Precaucin! La toma de corriente debe estar instalado cerca del equipo y debe quedar bien accesible.
*1 : If the date is not shown on the display, press to show the date. para hacer que se indique. *1 : Si la fecha no se muestra en el visualizador, pulse
MIXED CALCULATIONS / CLCULOS MIXTOS

A. + 12 = 5.

www.sharpusa.com
For your convenience, Genuine Sharp Supplies. Accessories, and additional Sharp Products can be purchased from the Authorized Sharp Reseller where you purchased your product or on-line at:
B. (10 + 2) 5 = 5 10. 12. 12. 60 + + =
Any consumable items such as paper, maintenance cartridge, ink cartridges supplied with the Product or to any equipment or any hardware, software, firmware, fluorescent lamp, power cords, covers, rubber parts, or peripherals other than the Product. At a Sharp Authorized Servicer located in the United States. To find out the location of the nearest Sharp Authorized Servicer, call Sharp toll free at 1-800-BE-SHARP.

= + 12 + 002 22

Where to Obtain Service :

10. 10. 22.

www.sharpplace.com
What to do to Obtain Service : Ship (prepaid) or carry in your Product to a Sharp Authorized Servicer. Be sure to have proof of purchase available. If you ship or mail the Product, be sure it is packaged carefully. TO OBTAIN SUPPLY, ACCESSORY OR PRODUCT INFORMATION, CALL 1-800-BE-SHARP.

EL-1801PIII (U1U)-2

Page 2
0 0. , , , , , , , 0 0. , , , , , , ,

04.5.27, 7:05 PM