Take the following points into consideration when selecting a site for this model.

ENVIRONMENT

The machine must be installed on a level surface. Keep the machine away from air conditioners, heaters, direct sunlight, and dust.
Provide easy access to the front, back, and sides of the machine. In
particular, keep the area in front of the machine clear, or the original document may jam as it comes out after scanning.
The temperature should be between 5 and 35C. The humidity should be between 30% and 85% (without condensation).

ELECTRICITY

AC 220-240V, 50/60Hz, earthed (2-prong) AC outlet is required.
2 If you are replacing the imaging film, take the old film out of the print-

Caution!

ing compartment and remove the three (3) green gears and the green flange from the ends of the spools. DO NOT DISCARD THE GREEN GEARS AND THE GREEN FLANGE!
Connection to a power source other than that specified will cause
damage to the equipment and is not covered under the warranty.
If your area experiences a high incidence of lightning or power surges,
we recommend that you install a surge protector for the power and telephone lines. Surge protectors can be purchased at most telephone speciality stores.
If the machine is moved from a cold to a warm place.
Condensation may form on the reading glass if machine is moved from a cold to a warm place, this will prevent proper scanning of documents for transmission. Turn on the power and wait approximately 2 hours before using machine.
3 Take the new film out of its package, and insert two of the gears
provided with the fax into the ends of the spool with film. Make sure that the two tabs on the gears fit properly into the slots in the ends of the spool.
7 Insert the empty spool into the back of the compartment so that the
Make sure that the gear engages with the gear below it.
gear and the flange fit into the slots on the sides of the compartment.
Do not yet remove the band which holds the spools together.
4 Hold the empty spool so that the end with only one slot is on the left,

Binary input

SW l E3

SW l F1

Not compatible
SW NO. DATA NO. SW l GSW l GChoice after quiet detect Reserved Busy tone detection ON/OFF time (Lower duration) Busy tone detection ON/OFF time (Upper duration) Reserved Busy tone detect continuation sound detect (during ICM: for internal A.M.) Reserved Busy tone detect intermittent sound detect (during ICM: for internal A.M.) Busy tone detection pulse number SW l ISW l IFax switching when A.M. full Reserved Reserved Reserved Reserved Busy tone continuous sound detect time Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved 5s 10s Yes No. 1 No. 2 No 2pulses Yes 4pulses No 6pulses 10pulses OPTION SW l H1 No. 3 No. 4 No Reserved Reserved Section time of quiet detection No. 5 No. 6 30s 40s 50s 60s 350ms 2700ms Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved OGM detect timer No. 1 No. 2 Not work 100ms 200ms 300ms ITEM Switch setting and function Initial setting TH Remarks
Wait response for 3sec 150ms No. 1 No. 0 650ms 0 0
Normal FAX RX 200ms 900ms Yes 250ms 1500ms 1 0

SW l H2

SW NO. DATA NO. SW l ISW l ISW l ISW l I3 SW l IReserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Activity report print Total communication hours and pages print Senders phone number setting Reserved Reserved Reserved Ringer volume No. 7 No. 8 Off Low Middle High ITEM Switch setting and function Initial setting TH OPTION Remarks
Automatic printout No Cannot change
No printout when memory full Yes Change allowed

OPTION

SW l J1
SW NO. DATA NO. SW l J2 SW l K2 SW l L2 SW l L2 SW l M8 Automatic reduce of receive Print contrast Reserved Reserved Reserved Reserved Entering DIAG mode by pressing SPEED key Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Cut off mode (COPY mode) A4 paper enable LEGAL & LETTER paper enable 2 IN 1 Mode Paper set size Yes No Polling key Reserved Reserved Reserved Reserved Reserved Automatic cover sheet Communication results printout (Transaction report) Yes No. 2 No. 3 No. 4 E/T/M 0 No Send only Always No print Err only Yes ITEM Speaker volume (3 stages) No. 1 No. 2 Switch setting and function 1 Low Low No 0 Middle High Initial setting TH LEGAL 100 % Normal 93 % A0 OPTION OPTION OPTION OPTION OPTION OPTION OPTION Remarks OPTION

SW l J2

Yes Enable Enable Yes No. 1 No. 2 Auto Light LETTER 0 0

No Disable Disable No

Reception reduction ratio in case of memory full 100 % Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved
SW NO. DATA NO. 3 SW l M3 SW l N3 SW l N3 SW l NReserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved ITEM Switch setting and function Initial setting TH Remarks
UX-510ATH FO-1470TH Soft switch function description
SW-A1 No. 1 Protect from echo Used to protect from echo in reception. SW-A1 No. 2 Forced 4800BPS reception When line conditions warrant that receptions take place at 4800BPS repeatedly. It may improve the success of receptions by setting at 4800BPS. This improves the receiving document quality and reduces handshake time due to fallback during training. SW-A1 No. 3 Footer print When set to "1", the date of reception, the sender machine No., and the page No. are automatically recorded at the end of reception. SW-A1 No. 4 Length limitation of copy/send/receive Used to set the maximum page length. To avoid possible paper jam, the page length is normally limited to 1 meter for copy or transmit, and 1.5 meters for receive. It is possible to set it to "No limit" to transmit a long document, such as a computer print form, etc. (In this case, the receiver must also be set to no limit.) SW-A1 No. 5 CSI transmission (CSI TRANSMISSION) is a switch to set whether the machine sends or does not send the signal (CSI signal) informing its own telephone No. to the remote fax machine when information is received. When "nonsending" is set, the telephone No. is not output on the remote transmitting machine if the remote transmitting machine has the function to display or print the telephone No. of receiving machine, using this CSI signal. SW-A1 No. 6 DIS receive acknowledgment during G3 transmission Used to make a choice of whether reception of DIS (NSF) is acknowledged after receiving two DISs (NSFs) or receiving one DIS (two NSFs). It may be useful for overseas communication to avoid an echo suppression problem, if set to 1. SW-A1 No. 7 Non-modulated carrier for V29 transmission mode Though transmission of a non-modulated carrier is not required for transmission by the V29 modem according to the CCITT recommendation, it may be permitted to a send non-modulated carrier before the image signal to avoid an echo suppression problem. It may be useful for overseas communication to avoid an echo suppression problem, if set to 1. SW-A1 No. 8 EOL (End Of Line) detect timer Used to make a choice of whether to use the 25-second or 13-second timer for detection of EOL. This is effective to override communication failures with some facsimile models that have longer EOL detection. SW-A2 No. 1 ~ No. 4 Modem speed Used to set the initial modem speed. The default is 9600BPS. It may be necessary to program it to a slower speed when frequent line fallback is encountered, in order to save the time required for fallback procedure. SW-A2 No. 5 Senders information transmit (SENDERS INFORMATION TRANSMISSION) is a switch to set the function to print the content of HEADER PRINT described in the passcode list at the front end of receivers original when original is sent to the remote machine. If this switch is set to "NO", the HEADER PRINT is not output at the receiving machine. SW-A2 No. 6 Reserved Set to "0". SW-A2 No. 7 Communication error treatment in RTN sending mode (Reception) Used to determine communication error treatment when RTN is sent by occurrence of a received image error in G3 reception. When it is set to "1", communication error is judged as no error. SW-A2 No. 8 CNG transmission When set to "0" , this model allows CNG transmission by pressing the Start key in the key pad dialing mode. When set to "1", CNG transmission in the key pad dialing mode cannot be performed. In either case. CNG transmission can be performed in the auto dial mode. SW-A3 No. 1, No. 2 CED tone signal interval For international communication, the 2100Hz CED tone may act as an echo suppression switch, causing a communication problem. Though SW-A3 No. 1 and No. 2 are normally set to 0, this selfing is used to change the time between the CED tone signal to eliminate the communication caused by echo.

Paper thickness (ref.) 0.06mm 0.09mm 0.06mm 0.09mm Paper size 128mm x 148mm ~ (MIN. SIZE) A4 (210mm x 297mm), Letter (216mm x 279mm) NOTE: Double-side coated documents and documents on facsimile recording paper should be inserted manually. The document feed quantity may be changed according to the document thickness. Documents corresponding to a paper weight heavier than 64.3kg (74.3g/m2 ) and lighter than 135kg (157g/m2 ) are acceptable for manual feed. Documents heavier than 135kg in terms of the paper weight must be duplicated on a copier to make it operative in the facsimile.
3-4. Loading the documents
1) Make sure that the documents are of suitable size and thickness, and free from creases, folds, curls, wet glue, wet ink, clips, staples and pins. 2) Place documents face down in the hopper.
3. Hopper mechanism 3-1. General view
i) Adjust the document guides to the document size. ii) Align the top edge of documents and gently place them into the hopper. The first page under the stack will be taken up by the feed roller to get ready for transmission. NOTES: 1) Curled edge of documents, if any, must be straighten out. 2) Do not load the documents of different sizes and/or thicknesses together.
Fig. 2 The hopper section contains document guides that are used to adjust the hopper to the width of the original document. This ensures that the original feeds straight into the fax machine for scanning. Document width: 148 mm to 216 mm (A5 longitudinal size to Letter longitudinal size) NOTE: Adjust the document guide after setting up the document.
3-5. Documents requiring use of copy
1) Documents smaller than 128mm x 148mm.

, ,, ,

Paper feed spring Separation rubber Paper feed roller

Fig. 4

5. Optical system (1) General view
Rear sheet Document Red mark LED lamp CCD PWB

Last page of document

First page of document
Reader glass Mirror 2 Mirror 3 Lens Mirror 1 CCD

Fig. 5

2) Documents thinner than the thickness of 0.06mm. 3) Documents containing creases, folds, or curls, especially those whose surface is curled (maximum allowable curl is 5mm). 4) Documents containing tears. 5) Carbon-backed documents. (Insert a white sheet of paper between the carbon back and the document carrier to avoid transfer of carbon to the carrier.) 6) Documents containing an easily separable writing material (e.g., those written with a lead pencil). 7) Transparent documents. 8) Folded or glued documents.

(2) Composition

The optical system is composed of the document feed mechanism, the LED lamp, the reflecting mirrors, the focusing lens, the CCD sensor, and the read process circuit.

5-1. LED Lamp/Lens

The LED lamp is used to project light to the document. NOTE: Take care for the position of the red mark on the lens. (Top of the light-projected side)

5-2. CCD

The CCD (charge coupled device) image sensor consists of a photodiode array which converts the intensity of light reflected from the document surface into series of analog voltages which are then stored in an ana log shift register. The series of analog voltages are then converted into a digital equivalent by a black/white binary logic circuit. (Example) Scan signal output waveform
4. Document release 4-1. General
To correct a jammed document or to clean the document running surface, pull the operation panel lock lever under the front center of the operation panel. To open the upper document guide, the operation panel must be opened first.

50% minimum

Maximum document width, 216mm

Scan line length

Fig. 6 1) The minimum output from the CCD at the maximum scan width of document (216mm) must be more than 50% of the peak value. 2) The peak output must be about 0.2 ~ 0.6 under room temperature to avoid CCD saturation.
UX-510ATH FO-1470TH 6. Recording block (1) General view
Imaging film Platen roller Guide shaft Thermal head

Take-up side

Pinch roller Paper guide
PO roller Supply side U turn guide RP hopper
Main frame PU roller Separate plate Film sensor lever P-IN sensor lever

Rotation plate

Fig. 7

6-1. Driving

In the drive mechanism, the rotating force of the pulse motor for both transmission and reception is transmitted to the paper supply roller, the recording paper feed roller and imaging film drive gear through the pulse motor axle gear, reduction gear and planetary gear.
3) Recording paper transfer sequence
a) The recording paper stored in the RP hopper is fed with the PU roller, and is stopped when the P-IN sensor is turned on by sensing its lead edge. b) Hereafter, the imaging film and recording paper are transferred with the recording paper feed roller, and thermal transcription is performed on the recording paper. c) After thermal transcription, the imaging film is taken up by the roller on the take-up side, and the recording paper is discharged by the PO roller. Troubleshooting the density unevenness mainly results from the longitu-dinal misalignment of the thermal head to the heater line. Other-wise, the head is in uneven contact with the recording paper feed roller, or the imaging film is wrinkled.

WRPROTN SXIN SXOUT TSTCLK DEBUGN RESETN XIN XOUT PWRDWNN BATRSTN INTPWRDWNEN

BUS INTERFACE

EXTERNAL CPU BUS
FAX MODEM DSP CORE (ML 94)
DRAM CONTROL INTERNAL & EXTERNAL BUS CONTROL INTERNAL & EXTERNAL DECODE DMA CONTROLLER

CPU BUS

GPIO[1]/SASTXD GPIO[2]/SASRXD GPIO[3]/SASCLK GPIO[4]/CPCIN GPIO[5]/SSCLK2 GPIO[6]/SSTXD2 GPIO[7]/SSRXD2 GPIO[8]/FWRN GPIO[9]/FRDN GPIO[10]/SSSTAT2 GPIO[11]/BE/SERINP GPIO[12]/CS2N GPIO[13]/CS3N GPIO[14]/CS4N GPIO[15]/CS5N GPIO[16]/IRQ8 GPIO[17] GPIO[18]/IRQ9N GPIO[19]/RDY/SEROUT GPIO[20]/ALTTONE SM[3:0/GPO[7:4] PM[3:0/GPO[3:0] GPIO[37]/IRQ15N GPIO[36:25] GPIO[30:26]
TONE GENERATOR GENERAL I/O ALTTONE GPIO CALLING PARTY CONTROL AUTOBAUD SYNC-ASYNC SASIF SSIF 2 FLASH MEMORY IF
OPERATOR PANEL IF 32 KEYS 8 LEDS LCD MODULE MOTOR POWER CONTROL RINGER SSIF 1
SEE "OPIF OUTPUTS" BELOW

INTERNAL CPU BUS

SEE "OPIF INPUTS" BELOW
SCANNER CONTROL & VIDEO PROCESSING 8-BIT PADC CCD/CIS SCANNER 5 ms,A4/B4 LINES SHADING CORRECTION(1:1,1:8) DITHERING MULTILEVEL B4-A4 REDUCTION ERROR DIFFUSION MTF.ETC.
BI-LEVEL RESOLUTION CONVERSION PROGRAMMABLE REDUCTION & EXPANSION
T.4/T.6 CODEC MH,MR,MMR HARDWARE,ALTEMATE COMPRESSION & DECOMPRESSION
THERMAL PRINTER IF 5 ms LINE TIME A4/B4 LINES TPH ADC 4 STROBE TPH LATCHLESS TPH EXTERNAL DMA I/F
THADIN PCLK/DMAACK PDAT PLAT STRB[3:0] STRBPOL/ DMAREQ

4.4 KB VIDEO RAM

DMA BUS

OPIF INPUTS

OPIF OUTPUTS LEDCTL/GPO[16] LCDCS/GPO[17] OPO[0]/GPO[8]/SMPWRCTRL OPO[1]/GPO[9]/PMPWRCTRL OPO[2]/GPO[10]/RINGER OPO[3]/GPO[11] OPO[4]/GPO[12]/SSTXD1 OPO[5]/GPO[13] OPO[6]/GPO[14] OPO[7]/GPO[15]
START CLK1 CLK1N/GPO[25] CLK2/GPO[24] FCSN[2]/VIDCTL[1]/GPO[22] FCSN[1]/VIDCTL[0]/GPO[26]
PWR/GND VIN VREFN/CLREF VREFP IVREFN IVREFP
OPI[0]/GPIO[21]/SSRXD1 OPI[1]/GPIO[22]/SSSTAT1 OPI[2]/GPIO[23]/SSCLK1 OPI[3]/GPIO[24]
SCE114 (IC9) Terminal descriptions
Pin No. 63 Pin List VSS D[3] D[2] D[1] D[0] A[23]/EYEXY A[22]/EYESYNC A[21]/EYECLK A[20] A[19] A[18] VDD A[17] A[16] A[15] A[14] VSS A[13] A[12] A[11] A[10] A[9] A[8] A[7] A[6] A[5] A[4] VDD A[3] A[2] A[1] A[0] GPIO[20]/ALTTONE NC NC NC NC NC GPIO[19]/RDY/SEROUT GPIO[11]/BE/SERINP VSS PCLK/DMAACK PDAT PLAT STRB[3] STRB[2] STRB[1] STRB[0] STRBPOL/DMAREQ VDD GPIO[17] GPIO[16]/IRQ[8] GPIO[15]/CS[5]n GPIO[14]/CS[4]n GPIO[13]/CS[3]n GPIO[12]/CS[2]n GPIO[4]/CPCIN VSS LEDCTL/GPO[16] NC LCDCS/GPO[17] GPIO[7]/SSRXD2 GPIO[6]/SSTXD2 I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O O O O O O O O I I/O I/O I/O I/O I/O I/O I/O O O I/O I/O Input Type Tu Tu Tu Tu Tu Tu Tu Tu Tu Tu Tu Tu Tu Tu Tu Tu Tu Tu Tu Tu Tu Tu Tu Tu Tu Tu Tu Tu Hu Hu Hu H Hu Hu Hu Hu Hu Hu Hu Hu Hu Output Type 13Xs 13Xs 13Xs 13Xs 13Xs 13Xs 13Xs 13Xs 13Xs 13Xs 13Xs 13Xs 13Xs 13Xs 13Xs 13Xs 13Xs 13Xs 13Xs 13Xs 13Xs 13Xs 13Xs 13Xs 13Xs 13Xs 13Xs 13Xs 13Xs 13Xs 13Xs 3XC 2XC 3XC 1XC 1XC 1XC 1XC 13Xs 13Xs 13Xs 13Xs 13Xs 13Xs 13Xs 4XC 1XC 13Xs 13Xs Pin Description Digital ground. CPU data bus. CPU data bus. CPU data bus. CPU data bus. CPU address bus. CPU address bus. CPU address bus. CPU address bus. CPU address bus. CPU address bus. Digital power. CPU address bus. CPU address bus. CPU address bus. CPU address bus. Digital ground. CPU address bus. CPU address bus. CPU address bus. CPU address bus. CPU address bus. CPU address bus. CPU address bus. CPU address bus. CPU address bus. CPU address bus. Digital power. CPU address bus. CPU address bus. CPU address bus. CPU address bus. GPIO[20] or ALTTONE. No connection. No connection. No connection. No connection. No connection. GPIO[19], bus ready or serial port data output for autobaud detection. GPIO[11], bus enable or serial port data input for autobaud detection. Digital ground. Thermal Print Head (TPH) clock or ext. DMA acknowledge. Serial printing data (to TPH). TPH data latch. Strobe signal for TPH. Strobe signal for TPH. Strobe signal for TPH. Strobe signal for TPH. Sets strobe polarity active high/low or ext. DMA request. Digital power. GPIO[17]. GPIO[16] or ext. interrupt with priority 8. GPIO[15] or I/O chip select 5. GPIO[14] or I/O chip select 4. GPIO[13] or I/O chip select 3. GPIO[12] or I/O chip select 2. GPIO[4] or Call Party Control input. Digital ground. Indicates the OPO[7:0] outputs are for LEDs or GPO[16]. No connection. LCD Chip select or GP0[17]. GPIO[7] or SSIF2 receive data. GPIO[6] or SSIF2 transmit data.

IMAGE SIGNAL

IMAGE SIGNAL RTC

1st page

RTC Cut line printed MPS
Next page insert command MPS

RTC Cut line printed EOP

IMAGE SIGNAL RTC EOP
DCN Recording paper ejected

DCN Document ejected

[2] Power on sequence
CPU initialized MODEM initialized

WAIT A MOMENT display

STOP key ? NO MEMORY CLEAR ? display 3 sec ? YES NO

STAND-BY START key ? NO

COPY key ? NO
STOP key ? NO 3 sec ? YES STAND-BY STAND-BY PROCESS CHECK MODE NO Memory clear Memory clear MEMORY CLEARED display MEMORY CLEARED display

CHAPTER 8. OTHERS

[1] Service tools

1. List

NO. PARTS CODE CPWBS2893SC02 UKOGM2057SCZZ Extension board unit Optical adjustment jig DESCRIPTION QTY PRICE RANK BZ BR

Extension board unit

CNTH2(*1)

CNSP2 CNCS2

CNCCD2

CNLED2 CNMT2

CNBZ2 CNPH1

HOOK SW PIN

1 A K E C

R3 DOOR SW

A K E C

CNCCD1

CNLED1

CNSP1 CNPN1

CNTH1(*1)
NOTE(*1): Mount connectors to CNTH1 and CNTH2 in the reverse direction against silk print of PWB.

NO. 25

PARTS CODE QCNW4723SCZZ CCNW4759SC01 QCNW4725SCZZ QCNW4726SCZZ QCNW4727SCZZ QCNW4728SCZZ QCNW4729SCZZ QCNW4730SCZZ QCNW4731SCZZ QCNW4732SCZZ QCNCM2401SC0B QCNCM2442SC0B QCNCM7014SC0B QCNCM7014SC0E QCNCM7014SC0F QCNCM7014SC0G QCNCM7014SC1E QCNCM7014SC1F QCNCM7014SC0D QCNCM7014SC0H VHPSG206S//-1 VRD-RC2EY000J VRDRC2EY221J QSW-Z2206SCZZ QSW-Z2226SCZZ CABLE [CNPN2] CABLE [CNTH2] CABLE [CNCCD2] CABLE [CNMT2] CABLE [CNLED2] CABLE [CNSP2] CABLE [CNCS2] CABLE [CNSNS] CABLE [CNPH2] CABLE [CNBZ2] CONNECTOR [CNSP1, CNSP2] CONNECTOR [CNCS1, CNCS2] CONNECTOR [CNLED1, CNLED2] CONNECTOR [CNSES] CONNECTOR [CNMT1, CNMT2] CONNECTOR [CNCCD1, CNCCD2] CONNECTOR [CNPN1, CNPN2] CONNECTOR [CNTH1, CNTH2] CONNECTOR [CNBZ1, 2] CONNECTOR [CNPH1, 2] PHOTO TRANSISTOR [P.E, RBN, PIN] RESISTOR (1/4W 0 5%)[R4] RESISTOR (1/4W 220 5%) [R1, R2, R3] HOOK SWITCH DOOR SWITCH

DESCRIPTION

PRICE RANK AL AX AH AH AF AF AF AH AN AH AA AB AD AB AB AB AC AD AB AB AG AA AA AH AG
UX-510ATH FO-1470TH 2. Description 2-1. Extension board unit
1. Remove the TEL/LIU PWB, control PWB and Power Supply PWB from this unit, and mount the extension board unit instead.
Before connecting the wiring to the extension board unit, set the
test PWB switches to the fixed position. 2. The setting is as follows.
A set with a mounted extension board unit
Connector CNPN2 CNTH2 CNCCD2 CNMT2 CNLED2 Cable QCNW-4723SCZZ CCNW-4759SC01 QCNW-4725SCZZ QCNW-4726SCZZ QCNW-4727SCZZ QCNW-4728SCZZ QCNW-4729SCZZ QCNW-4731SCZZ QCNW-4732SCZZ QCNW-4730SCZZ Cable color 1. Brown 2. Red 3. Orange 4. Yellow 5. Green CNSNS RHS DRSNS N.C. RBN PIN Connected to (PWB) TP2 (TEL/LIU) DOOR SW (Control) RBNSNS (Control) PINSNS (Control)
CNSP2 CNCS2 CNPH2 CNBZ2 CNSNS
The hook switch are operated by OR of the mechanical unit switch and the test PWB switch. When performing installation in the machine unit, set the test PWB switches to the fixed position. Mechanical unit PWB to be tested ON-HOOK ON/OFF operation
Actual operation with mechanical unit

RBNSNS

Hook SW Hook SW
ON/OFF operation PWB sensor check ON-HOOK

J17 TP2 J13

PINSNS
* Recording paper: ON No recording paper: OFF

DON'T SEPARATE

CHECK TEL/LIU PWB

CHECK CONTROL PWB

RELAY CABLE
Note: For the thermal head cable only, connect to the relay cable, not to the relay PWB.
2-2. Scan optical system adjustment

(1) Outline

The adjustment procedures of the scan optical system are described below:
H Lightly loosen the red screws of the CCD PWB and obtain the VID
signal waveform in synchronization with T signal waveform. Adjust the CCD PWB positioning to obtain the waveform as shown below.

Scan adjustment jig

(2) Adjustment procedures
1 Switch off the machine and disconnect the AC power cable from the wall socket. 2 Fully open the upper cabinet, remove the fixing screws of the record3 Disconnect the main PWB from the TEL/LIU PWB. 4 Connect your oscilloscope channel 1 to the VIN signal and channel 2
ing paper tray and remove the recording paper tray. In order to perform a focus adjustment, remove the optical system unit from the frame.
of your oscilloscope to T signal (Refer Pin 4 of connector CNCCD on the main pwb). Connect the earth clips of either probe to AG ground as shown. Set the trigger to channel 2.

IC5: RH-iX2168SCZZ (MSM51V4800E)
VCC 1 DQDQDQDQNC 6 WE 7 RAS 8 A9R 9 AAAAVCC 14

28 VSS 27 DQ8

IC13: VHiSCE114//-1 (20415)
NC ICLK NC NC NC NC MCLK NC
26 DQ7 PIN NAME A0~A8, A9R 24 DQ5 RAS 23 CAS CAS DQ1~DQOE OE 21 NC WE VCC 20 A8 VSS NC 19 ADQAAAVSS SIGNAL ADDRESS INPUT ROW ADDRESS STROBE COLUMN ADDRESS STROBE DATA INPUT/OUTPUT OUTPUT ENABLE WRITE ENABLE POWER SUPPLY (+3.3V) GROUND NO INTERNAL CONNECTION
CTRLSIN Reserved Reserved SOUT SIN FSYNC POR AVSS
AVSS AVDD AGND VREF MICBIAS MICIN MICIN+ LINEIN
MODE0 MODE1 Reserved DVDD DVSS SPKRO SPKRO+ LINEO
IC9: VHiSCE114//-1 (SCE114)
GPIO[31] GPIO[32] GPIO[33] GPIO[34] GPIO[35] GPIO[36] VDD GPIO[0]/SR4IN GPO[31]/SR3OUT GPIO[37]/IRQ15N IARESET IACLK/DSPCSN IA1CLK SR3IN/DSPIRQN SR4OUT SR1IO SA1CLK VSSPLL TSTCLK DEBUGN RDN WRN SYNC/GPO[20] ROMCSN CS1N/GPO[21] VSS SXIN SXOUT VDD PM[3]/GPO[3] PM[2]/GPO[2] PM[1]/GPO[1] PM[0]/GPO[0] SM[3]/GPO[7] SM[2]/GPO[6] SM[1]/GPO[5] SM[0]/GPO[4] REGDMA/GPO[18] WAITN/GPO[19] VDDPLL D[7] D[6] D[5] D[4] 175 176
VSS D[3] D[2] D[1] D[0] A[23]/EYEXY A[22]/EYESYNC A[21]/EYECLK A[20] A[19] A[18] VDD A[17] A[16] A[15] A[14] VSS A[13] A[12] A[11] A[10] A[9] A[8] A[7] A[6] A[5] A[4] VDD A[3] A[2] A[1] A[0] GPIO[20]/ALTTONE NC NC NC NC NC GPIO[19]/RDY/SEROUT GPIO[11]/BE/SERINP VSS PCLK/DMAACK PDAT PLAT
VREFP ADXG ADVA ADGA VIN VREFN/CLREF ADGA NC PWRDWNN INTPWRDWNEN BATRSTN TEST[0] TEST[1] CS0N WRPROTN XOUT XIN VBAT DWRN CAS[0]N CAS[1]N RASN VDRAM GPIO[10]/SSSTAT2 GPIO[5]/SSCLK2 GPIO[6]/SSTXD2 GPIO[7]/SSRXD2 LCDCS/GPO[17] NC LEDCTRL/GPO[16] VSS GPIO[4]/CPCIN GPIO[12]/CS[2]N GPIO[13]/CS[3]N GPIO[14]/CS[4]N GPIO[15]/CS[5]N GPIO[16]/IRQ[8] GPIO[17] VDD STRBPOL/DMAREQ STRB[0] STRB[1] STRB[2] STRB[3]
GPIO[30] GPIO[29] GPO[30] GPO[29] GPO[28] GPO[27] GPO[26] GPIO[28] GPIO[27] GPIO[26] GPIO[25] VSS TONE VDD START CLK1 CLK1N/GPO[25] CLK2/GPO[24] FCSN[1]/VIDCTL[0]/GPO[23] FCSN[2]/VIDCTL[1]/GPO[22] PGIO[8]/FWRN PGIO[9]/FRDN PGIO[1]/SASTXD PGIO[2]/SASRXD PGIO[3]/SASCLK PGIO[18]/IRQ[9]N VSS RESETN OPI[0]/GPIO[21]/SSRXD1 OPI[1]/GPIO[22]/SSSTAT1 OPI[2]/GPIO[23]/SSCLK1 OPI[3]/GPIO[24] OPO[0]/GPO[8]/SMPWRCTRL OPO[1]/GPO[9]/PMPWRCTRL OPO[2]/GPO[10]/RINGER OPO[3]/GPO[11] OPO[4]/GPO[12]/SSTXD1 OPO[5]/GPO[13] OPO[6]/GPO[14] OPO[7]/GPO[15] THADI VDD VREFP VREFN

PARTS GUIDE

UX-510A MODEL FO-1470
SELECTION CODE TH DESTINATION Thailand

Cabinet, etc.

Packing material & Accessories

Upper cabinet

Control PWB unit

Document guide upper

TEL/LIU PWB unit

Optical unit

10 Power supply PWB unit

Drive unit

11 Operation panel PWB unit
Because parts marked with " " are indispensable for the machine safety maintenance and operation, it must be replaced with the parts specific to the product specification.

[510A] [1470]

N N N N N N N N N
[510A] [1470] [510A] [1470]

N N N N

N N N N N N
B2 B3 B4 B5 B7 B10 B11 W1 W2 PCOVA2114XHYZ GLEGG2063XHZZ PSHEZ3563XHZZ PSHEZ3332XHZZ LBNDJ2008SCZZ PSHEZ3341XHZZ PSHEZ3342XHZZ PCUSG2112XHZZ LPLTP2968XHZZ NROLP2396XHZZ PCUSS2114XHZZ LPLTM3122XHZZ MSPRP3123XHZZ HPNLH2405XHSD HPNLH2405XHSE PGIDM2493XHSA PSHEP3647XHZZ XEBSD30P10000 LX-BZ2222XHZZ XBPSD30P06K00 XBPSN40P06K00 LX-BZ2138XHZZ XEBSE30P10000 XEBSF30P12000 LX-WZ2228XHZZ LX-WZ2246XHZZ AE AC AB AE AA AC AC AE AP AD AD AD AC AH AH AF AB AA AC AA AA AB AA AA AB AB N N C C C C C C C C C C C C C D D C C C C C C C C C C C Side cover Rubber leg Jack sheet Hopper sheet Band(Black) Guide sheet, left Guide sheet, right PO gear cushion Document kick plate Document kick roller PO cushion Earth plate Speaker holder spring Decoration panel Decoration panel A4 paper guide U turn guide sheet Screw(3x10) Screw Screw(3x6) Screw(4x6) Screw(3x6) Screw(3x10) Screw(3x12) Cut washer Washer

[2] Upper cabinet

PARTS CODE

PRICE RANK

NEW MARK

PART RANK

BDCEKP351BXH02 GCABA2289XHYC GCABA2289XHYG JBTN-2202XHYA JBTN-2202XHSC JBTN-2203XHYA JBTN-2203XHSC JBTN-2204XHYA JBTN-2204XHSB JBTN-2205XHYA JBTN-2205XHSB JBTN-2206XHYA JBTN-2206XHYB PSHEZ3291XHZZ QSW-M2246AXZZ QSW-M2247AXZA QCNW-390AXHZZ QSW-K0005AWZZ XEBSD20P06000 (Unit) DCEKP264CXH03 DCEKP264CXH07 BF AP AN AH AG AF AF AE AD AD AD AE AC AD AH AE AK AC AA BE BF N N N N N N N N N E D D C C C C C C C C C C C C C C C C E E Operation panel PWB unit Upper cabinet Upper cabinet 12 key 12 key Direct key Direct key Start key Start key Stop key Stop key Mode key Mode key Insulation sheet FRSNS sensor ORGSNS sensor Panel cable Tact switch Screw(2x6) Operation panel unit Operation panel unit [510A] [1470] [510A] [1470] [510A] [1470] [510A] [1470] [510A] [1470] [510A] [1470] [FRSNS] [ORGNSN] [SW]

[3] Document guide upper

17 LPLTG2707XHZZ LPLTP2790XHZZ MLEVP2257XHZA MSPRC2924XHFJ MSPRD3197XHZZ MSPRT2923XHFJ MSPRT3235XHZZ NBRGP2141XHZZ NGERH2275XHZZ NGERH2317XHZZ NGERH2356XHZZ NROLP2334XHZA NROLR2466XHZZ NSFTZ2257XHZZ PGIDM2482XHAZ PSHEZ3290XHZZ MARMP2026XHZZ AE AD AE AC AD AC AB AH AC AC AC AC AK AG AM AD AC N N N C C C C C C C C C C C C C C C C C Separation rubber Separate plate Panel lock lever Pinch roller spring Paper feed spring Panel lock lever spring Separate spring Transfer bearing Transfer gear 2 Idler gear,28Z Idler gear,20Z Pinch roller Transfer roller Pinch roller shaft Document guide upper Rear sheet Paper feed arm

AX AP AG AG AC AC AE AV AE AG AC AC AR AR AG AD AD
[510A] [1470] [510A] [1470] [510A] [1470] [510A] [1470]

[8] Control PWB unit

UBATL2049SCZZ VCEAGA1EW476M VCEAGA1HW107M VCEAGA1HW106M VCEAGA1HW107M VCEAGA0JW227M VCEAGA0JW227M VCEAGA1HW107M VCEAGA1HW226M VCEAGA1EW476M VCEAGA1HW106M VCEAGA1HW107M VCEAGA1HW106M VCEAGA1HW106M VCKYCY1EF104Z VCKYCY1AF105Z VCKYCY1AF105Z VCKYTV1HF104Z VCCCCY1HH101J VCCCCY1HH101J VCKYCY1HB102K VCKYCY1HB102K VCKYCY1AF105Z VCKYCY1HB102K VCKYCY1HB102K VCKYTV1CF225Z VCCCCY1HH180J VCCCCY1HH330J VCKYCY1AF105Z VCKYCY1AF105Z VCKYTV1HF104Z VCKYCY1EF104Z VCKYCY1AF105Z VCKYCY1AF105Z VCKYCY1EF104Z VCKYCY1AF105Z VCKYCY1HB102K VCKYCY1HB102K VCKYCY1HB102K VCKYTV1CF225Z VCKYCY1EF104Z VCKYCY1AF105Z VCKYCY1AF105Z VCKYCY1AF105Z VCKYCY1AF105Z VCKYCY1AF105Z VCKYTV1CF225Z VCKYCY1AF105Z VCKYCY1HB102K VCCCCY1HH101J VCKYTV1CF225Z VCKYTV1CF225Z VCKYCY1HB102K VCKYCY1HB102K VCKYCY1HB102K VCKYCY1HB102K VCCCCY1HH101J VCKYCY1EF104Z VCKYTV1CF225Z VCKYTV1CF225Z VCKYTV1CF225Z VCKYTV1CF225Z VCKYTV1CF225Z VCCCCY1HH101J VCCCCY1HH101J VRS-CY1JB000J VCKYCY1HB103K VCKYCY1HB472K VCKYCY1AF105Z VCCCCY1HH150J VCCCCY1HH150J VCKYCY1EF104Z VCCCCY1HH101J VCCCCY1HH101J VCCCCY1HH101J VCCCCY1HH101J VCKYCY1EF104Z VCCCCY1HH150J VCKYTV1HF104Z VRS-CY1JB000J AF AA AA AA AA AD AD AA AB AA AA AA AA AA AA AC AC AA AA AA AA AA AC AA AA AD AA AA AC AC AA AA AC AC AA AC AA AA AA AD AA AC AC AC AC AC AD AC AA AA AD AD AA AA AA AA AA AA AD AD AD AD AD AA AA AA AA AA AC AB AB AA AA AA AA AA AA AB AA AA B C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C Battery(CR2032T23) Capacitor(25WV 47F) Capacitor(50WV 100F) Capacitor(50WV 10F) Capacitor(50WV 100F) Capacitor(6.3WV 220F) Capacitor(6.3WV 220F) Capacitor(50WV 100F) Capacitor(50WV 22F) Capacitor(25WV 47F) Capacitor(50WV 10F) Capacitor(50WV 100F) Capacitor(50WV 10F) Capacitor(50WV 10F) Capacitor(25WV 0.1F) Capacitor(10WV 1F) Capacitor(10WV 1F) Capacitor(50WV 0.1F) Capacitor(50WV 100PF) Capacitor(50WV 100PF) Capacitor(50WV 1000PF) Capacitor(50WV 1000PF) Capacitor(10WV 1F) Capacitor(50WV 1000PF) Capacitor(50WV 1000PF) Capacitor(16WV 2.2F) Capacitor(50WV 18PF) Capacitor(50WV 33PF) Capacitor(10WV 1F) Capacitor(10WV 1F) Capacitor(50WV 0.1F) Capacitor(25WV 0.1F) Capacitor(10WV 1F) Capacitor(10WV 1F) Capacitor(25WV 0.1F) Capacitor(10WV 1F) Capacitor(50WV 1000PF) Capacitor(50WV 1000PF) Capacitor(50WV 1000PF) Capacitor(16WV 2.2F) Capacitor(25WV 0.1F) Capacitor(10WV 1F) Capacitor(10WV 1F) Capacitor(10WV 1F) Capacitor(10WV 1F) Capacitor(10WV 1F) Capacitor(16WV 2.2F) Capacitor(10WV 1F) Capacitor(50WV 1000PF) Capacitor(50WV 100PF) Capacitor(16WV 2.2F) Capacitor(16WV 2.2F) Capacitor(50WV 1000PF) Capacitor(50WV 1000PF) Capacitor(50WV 1000PF) Capacitor(50WV 1000PF) Capacitor(50WV 100PF) Capacitor(25WV 0.1F) Capacitor(16WV 2.2F) Capacitor(16WV 2.2F) Capacitor(16WV 2.2F) Capacitor(16WV 2.2F) Capacitor(16WV 2.2F) Capacitor(50WV 100PF) Capacitor(50WV 100PF) Resistor(1/16W 0 5%) Capacitor(50WV 0.01F) Capacitor(50WV 4700PF) Capacitor(10WV 1F) Capacitor(50WV 15PF) Capacitor(50WV 15PF) Capacitor(25WV 0.1F) Capacitor(50WV 100PF) Capacitor(50WV 100PF) Capacitor(50WV 100PF) Capacitor(50WV 100PF) Capacitor(25WV 0.1F) Capacitor(50WV 15PF) Capacitor(50WV 0.1F) Resistor(1/16W 0 5%) [BAT1] [C1] [C2] [C3] [C4] [C5] [C6] [C7] [C8] [C11] [C12] [C13] [C14] [C15] [C100] [C101] [C102] [C104] [C105] [C107] [C109] [C110] [C111] [C112] [C113] [C114] [C115] [C116] [C117] [C118] [C125] [C126] [C127] [C128] [C129] [C130] [C131] [C132] [C133] [C134] [C135] [C136] [C137] [C138] [C139] [C140] [C141] [C142] [C143] [C144] [C146] [C147] [C148] [C149] [C150] [C151] [C152] [C154] [C157] [C158] [C159] [C160] [C161] [C163] [C164] [C168] [C169] [C170] [C171] [C174] [C175] [C176] [C177] [C178] [C179] [C180] [C182] [C183] [C185] [C186]

901 (Unit) DCEKC881PXHZZ BT N E Control PWB unit(Within ROM)

[9] TEL/LIU PWB unit

VHVRA391PV6-1 QCNW-4704XHZZ VCEAGA1HW226M VCEAGA1HW226M VCEAGA1HW475M VCEAGA1HW226M VCEAGA1HW226M RC-FZ3024SCZZ VCEAGA1HW226M VCEAGA1HW106M VCEAGA1HW226M VCKYCY1EF104Z VCKYTV1HF104Z VRS-CY1JB000J VRS-CY1JB000J VCCCCY1HH330J VCKYTV1HF104Z VCKYCY1HB821K VRS-CY1JB000J VCCCCY1HH330J VCCCCY1HH221J VCKYCY1HB222K VCKYTV1HF104Z VCKYCY1HB102K VCKYCY1CB104K VCKYCY1HB103K VCCCCY1HH221J VCKYCY1HB102K VCKYCY1HB222K RRLYD3433XHZZ QJAKZ2079XH0D QCNCW2500SC1D QJAKZ2046SCBB VHDDSS133//-1 VHDDSS133//-1 VHDDA204K//-1 VHINJM2904M-2 VHINJM2904M-2 RFILN2027XHZZ RFILN2027XHZZ RFILN2027XHZZ RFILN2027XHZZ RFILN2027XHZZ RFILN2027XHZZ RFILN2027XHZZ VHPTLP521-1BL VSDTC143ZK/-1 VSDTC143ZK/-1 VS2SC2412KR-1 VRD-HT2HY223J VRS-TS2AD102J VRS-TS2AD101J VRS-CY1JB332J VRS-TS2AD433J VRS-CY1JB203J VRS-CY1JB623J VRS-CY1JB513J VRS-CY1JB473J VRS-CY1JB621J VRS-CY1JB472J VRS-CY1JB101J VRS-CY1JB203J VRS-CY1JB102J VRSTS2AD8662F VRS-CY1JB000J VRS-CY1JB332J VRS-CY1JB224J VRS-TS2AD151J VRS-CY1JB102J VRS-CY1JB152J VRS-CY1JB822J VRS-CY1JB683J VRS-CY1JB000J VRS-CY1JB102J VRS-CY1JB103J VRS-CY1JB332J
AE AD AB AB AA AB AB AG AB AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AH AD AG AH AA AA AC AG AG AC AC AC AC AC AC AC AE AD AD AD AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA
B C C C C C C C C C C C C C C C C C C C C C C C C C C C C B C C C B B B B B C C C C C C C B B B B C C C C C C C C C C C C C C C C C C C C C C C C C C C
Varistor(RA-391P-V6-2) Cable Capacitor(50WV 22F) Capacitor(50WV 22F) Capacitor(50WV 4.7F) Capacitor(50WV 22F) Capacitor(50WV 22F) Capacitor(250WV 0.82F) Capacitor(50WV 22F) Capacitor(50WV 10F) Capacitor(50WV 22F) Capacitor(25WV 0.1F) Capacitor(50WV 0.1F) Resistor(1/16W 0 5%) Resistor(1/16W 0 5%) Capacitor(50WV 33PF) Capacitor(50WV 0.1F) Capacitor(50WV 820PF) Resistor(1/16W 0 5%) Capacitor(50WV 33PF) Capacitor(50WV 220PF) Capacitor(50WV 2200PF) Capacitor(50WV 0.1F) Capacitor(50WV 1000PF) Capacitor(16WV 0.1F) Capacitor(50WV 0.01F) Capacitor(50WV 220PF) Capacitor(50WV 1000PF) Capacitor(50WV 2200PF) Relay(OUAZ-SH-124DZ) Jack Connector(14pin) Jack Diode(1SS133) Diode(1SS133) Diode(DA204K) IC(NJM2904M) IC(NJM2904M) Coil(R-5C) Coil(R-5C) Coil(R-5C) Coil(R-5C) Coil(R-5C) Coil(R-5C) Coil(R-5C) Photo coupler(TLP521) (DTC143ZK) (DTC143ZK) Transistor(2SC2412KR) Resistor(1/2W 22K 5%) Resistor(1/10W 1K 5%) Resistor(1/10W 100 5%) Resistor(1/16W 3.3K 5%) Resistor(1/10W 43K 5%) Resistor(1/16W 20K 5%) Resistor(1/16W 62K 5%) Resistor(1/10W 51K 5%) Resistor(1/16W 47K 5%) Resistor(1/16W 620 5%) Resistor(1/16W 4.7K 5%) Resistor(1/16W 100 5%) Resistor(1/16W 20K 5%) Resistor(1/16W 1K 5%) Resistor(1/10W 86.6K 1%) Resistor(1/16W 0 5%) Resistor(1/16W 3.3K 5%) Resistor(1/16W 220K 5%) Resistor(1/10W 150 5%) Resistor(1/16W 1K 5%) Resistor(1/16W 1.5K 5%) Resistor(1/16W 8.2K 5%) Resistor(1/16W 68K 5%) Resistor(1/16W 0 5%) Resistor(1/16W 1K 5%) Resistor(1/16W 10K 5%) Resistor(1/16W 3.3K 5%)

AA AA AA AA AA AA AA AA AA AA AB AB AB AB AB AB AB AB AA AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AB AB AB AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AD AD AD AD C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C
VCKYTV1CF225Z VCKYTV1HF104Z VCTYPA1HF104Z VHDDA204K//-1 VHDDSS133//-1 VHDHRW0202B-1 VHD1SS355//-1 VHEHZ2C1///-1 VHEHZ27-1//-1 VHEMTZJ5R1B-1 VHE1N4748A/-1 VHIKID65001AP VHINJM2113M-1 VHINJM2904M-2 VHINJM318M/-F VHISCE114//-1 VHITCD1208AP1 VHI27020FRW0A VHI62FP332P-1 VHPSG206S//-1 VHPSNK15A24-1 VHPTLP521-1BL VHVERZV5D471/ VHVRA391PV6-1 VRD-HT2HY223J VRD-RC2EY222J VRD-RC2EY390J VRS-CY1JB000J
8-52 8-59 8-60 8-61 8-62 8-63 8-18 8-31 8-79 9-13 9-17 9-23 8-98 9-36 9-34 9-35 8-111 8-109 8-110 8-112 8-113 8-114 8-115 9-87 9-88 9-89 9-90 8-108 8-117 8-127 9-37 9-38 8-125 8-123 8-126 11-4 8-120 8-234 8-134 8-135 4-14 9-46 9-85 9-86 9-1 9-50 11-6 11-7 8-66 8-80 8-84 8-86 8-89 8-90 8-128 8-129 8-130 8-132 8-133 8-143 8-149 8-150 8-151 8-153 8-154 8-156 8-161 8-166 8-167 8-181 8-183 8-194 8-195 8-198 8-199 8-203 8-206 8-211 8-212 8-214
AD AD AD AD AD AD AA AA AA AA AA AA AC AC AA AA AD AB AB AB AB AB AB AA AA AB AB AC AE AG AG AG AF BG BG AX N AF AG AG AZ AE AC AC AE AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA C C C C C C C C C C C C C B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C
AF AA AA AA AA AA AA AA AA AA AA AB AB AB AA AA AA AA AA AA AA AA AA AD AD AA
VRS-CY1JB000J VRS-CY1JB101J VRS-CY1JB102J VRS-CY1JB103J VRS-CY1JB104J VRS-CY1JB105J VRS-CY1JB106J VRS-CY1JB152J VRS-CY1JB203J VRS-CY1JB221J VRS-CY1JB222J VRS-CY1JB223J VRS-CY1JB224J VRS-CY1JB271J VRS-CY1JB302J VRS-CY1JB332J VRS-CY1JB333J VRS-CY1JB334J VRS-CY1JB433J VRS-CY1JB471J VRS-CY1JB472J VRS-CY1JB473J VRS-CY1JB474J VRS-CY1JB513J