LC-3237X20E-gb.indd 1

2007/08/31 16:57:12

OPERATION MANUAL

Introduction

Dear SHARP customer

Thank you for your purchase of the SHARP LCD colour TV product. To ensure safety and many years of troublefree operation of your product, please read the Important Safety Precautions carefully before using this product.
Important Safety Precautions
CleaningUnplug the AC cord from the AC outlet before cleaning the product. Use a damp cloth to clean the product. Do not use liquid cleaners or aerosol cleaners. Water and moistureDo not use the product near water, such as bathtub, washbasin, kitchen sink, laundry tub, swimming pool and in a wet basement. Do not place vases or any other water-filled containers on this product. The water may spill onto the product causing fire or electric shock. StandDo not place the product on an unstable cart, stand, tripod or table. Doing so can cause the product to fall, resulting in serious personal injuries as well as damage to the product. Use only a cart, stand, tripod, bracket or table recommended by the manufacturer or sold with the product. When mounting the product on a wall, be sure to follow the manufacturers instructions. Use only the mounting hardware recommended by the manufacturer. When relocating the product placed on a cart, it must be moved with utmost care. Sudden stops, excessive force and uneven floor surface can cause the product to fall from the cart. VentilationThe vents and other openings in the cabinet are designed for ventilation. Do not cover or block these vents and openings since insufficient ventilation can cause overheating and/or shorten the life of the product. Do not place the product on a bed, sofa, rug or other similar surface, since they can block ventilation openings. This product is not designed for built-in installation; do not place the product in an enclosed place such as a bookcase or rack, unless proper ventilation is provided or the manufacturers instructions are followed. The LCD panel used in this product is made of glass. Therefore, it can break when the product is dropped or impact applied. If the LCD panel is broken, be careful not to be injured by broken glass. Heat sourcesKeep the product away from heat sources such as radiators, heaters, stoves and other heat-generating products (including amplifiers). To prevent fire, never place any type of candle or naked flames on the top or near the TV set. To prevent fire or shock hazard, do not place the AC cord under the TV set or other heavy items. Do not display a still picture for a long time, as this could cause an afterimage to remain. There is power consumption always if main plug is connected. ServicingDo not attempt to service the product yourself. Removing covers can expose you to high voltage and other dangerous conditions. Request a qualified person to perform servicing.

The LCD panel is a very high technology product, giving you fine picture details. Due to the very large number of pixels, occasionally a few non-active pixels may appear on the screen as a fixed point of blue, green or red. This is within product specifications and does not constitute a fault.
Precautions when transporting the TV
When transporting the TV, never carry it by holding onto the speakers. Be sure to always carry the TV by two people holding it with two hands one hand on each side of the TV.

Trademarks

HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. TruSurround XT, SRS and h symbol are trademarks of SRS Labs, Inc.
The HD ready 1080P Logo is a trademark of EICTA.
The DVB logo is the registered trademark of the Digital Video Broadcasting - DVB - project.

LC-3237X20E-gb.indd 2

2007/08/31 16:57:15

Remote control unit

B (Standby/On) (Page 10) Buttons for useful operations m (Teletext) ATV: Display analogue teletext. (Page 14) DTV: Select MHEG-5 and teletext for DTV. (Page 14) k (Reveal hidden Teletext) (Page 14) [ (Subtitle) ATV/DTV/External: Switch subtitle languages on/off. (Pages 14 and 28) 3 (Freeze/Hold) Press to freeze a moving image on the screen. TELETEXT: Stop updating Teletext pages automatically or release the hold mode. 1 (Subpage) (Page14) v (Top/Bottom/Full) Set the area of magnification in teletext mode. (Page 14) 0 - 9 numeric buttons Set the channel. Enter desired numbers. Set the page in teletext mode. A (Flashback) Press to return to the previous image in normal viewing mode. DTV Press to access DTV mode. ATV Press to access conventional analogue TV mode. 2 (Sound mode) Select the sound multiplex mode. (Page 10) i (k/l) (Volume) Increase/decrease TV volume. e (Mute) TV sound on/off f (WIDE MODE) Select the wide mode. (Pages 29 and 33) AV MODE Select a video setting. (Page 25) a/b/c/d (Cursor) Select a desired item on the setting screen. OK Execute a command within the menu screen. ATV/DTV: Display the programme list when no other menu screen is running. END Exit the menu screen. R/G/Y/B (Colour) buttons On the menu screen, the coloured buttons are correspondingly used to select the coloured items on the screen. (e.g. EPG, MHEG-5, TELETEXT) 15 b (INPUT SOURCE) Select an input source. (TV, EXT1, EXT2, EXT3, EXT4, EXT5, EXT6, EXT7, EXT8) (Page 10) 16 EPG DTV: Display the EPG screen. (Pages 11 - 13) 17 RADIO DTV: Switch between Radio and Data mode. When only data broadcasting (no radio broadcasting) is transmitted by DVB, switching to Data mode will be performed. 18 P. INFO Press to display programme information which is transmitted through digital video broadcasting in the upper left corner of the screen. (DTV only) 19 P (r/s) Select the TV channel. 20 p (Display information) Press to display the station information (channel number, signal, etc.) in the upper right corner of the screen. (Page 31) 21 SLEEP Press to schedule a time for the TV to automatically standby. (Page 26) 22 MENU ATV/DTV: Menu screen on/off. (Return) Return to the previous menu screen. 24 ACTION (Action Mode) This key does not work on this model. 25 AQUOS LINK buttons If external equipment such as a AQUOS BD Player is connected via HDMI cables and is AQUOS LINK compatible, you can use these AQUOS LINK buttons. See pages 20 and 22 for details.

LC-3237X20E-gb.indd 3

2007/09/14 13:31:33

TV (Front view)

Remote control sensor OPC sensor
OPC indicator SLEEP indicator B (Standby/On) indicator

TV (Rear view)

P (r/s) Programme [channel] buttons i (k/l) Volume buttons b (INPUT SOURCE) button MENU button a (Power) button
EXT 4 (HDMI) terminal EXT 5 (HDMI) terminal EXT 7 (ANALOGUE RGB/AUDIO) terminals DIGITAL AUDIO OUTPUT terminal OUTPUT (AUDIO) terminals Antenna terminal
EXT 6 (HDMI/AUDIO) terminals RS-232C terminal EXT 8 (COMPONENT/AUDIO) terminals EXT 2 (RGB) terminal EXT 1 (RGB) terminal
EXT 3 terminals Headphones SERVICE socket COMMON INTERFACE slot AC INPUT terminal

LC-3237X20E-gb.indd 4

2007/08/31 16:57:18

Preparation

Supplied accessories
Remote control unit (g1) AC cord (For Europe, except U.K. and Eire) (For U.K. and Eire) Cable clamp (g1) Stand unit (g1)
U.K. type 3-pin AC cord is only included with models LC-32X20E and LC-37X20E. Pages 3 and 6 Operation manual (This publication) Page 8 Page 8 AAA size battery (g2). Page 6 Page 5

Attaching the stand unit

Before attaching (or detaching) the stand, unplug the AC cord from the AC INPUT terminal. Before performing work spread cushioning over the base area to lay the TV on. This will prevent it from being damaged. CAUTION Attach the stand in the correct direction. Be sure to follow the instructions. Incorrect installation of the stand may result in the TV falling over.
Confirm that there are 10 screws with the stand unit.
1 Insert the stand into the openings on the bottom of the TV. (Hold the stand so it will not drop from the edge of the base area.) 2 Insert and tighten the 4 screws into the 4 holes on the rear of the TV.
Attach the supporting post for the stand unit onto the base using the 6 screws with the screw driver (supplied) as shown. 2

Soft cushion

NOTE To detach the stand unit, perform the steps in reverse order.

LC-3237X20E-gb.indd 5

2007/08/31 16:57:21

Inserting the batteries

Before using the TV for the first time, insert two AAA size batteries (supplied). When the batteries become depleted and the remote control unit fails to operate, replace the batteries with new AAA size batteries.
Open the battery cover. Insert two supplied AAA size batteries.

HDMI device (Page 16)

HDMI Cable

DVI/HDMI Cable

Game console or camcorder (Page 16)
3.5 mm stereo minijack cable S-video cable* or or

AV cable*

Audio device (Page 18)

Optical audio cable

Audio cable SCART cable
Video recording device (Pages 16 and 17)

Audio cable

Component cable * When using an S-video cable, you also need to connect an audio cable (R/L). 15

LC-3237X20E-gb.indd 15

2007/08/31 16:58:03

HDMI connection

Example of connectable devices
E DVD E Blu-ray player/recorder The HDMI connections (High Definition Multimedia Interface) permit digital video and audio transmission via a connection cable from a player/recorder. The digital picture and sound data are transmitted without data compression and therefore lose none of their quality. Analogue/digital conversion is no longer necessary in the connected devices, which also would result in quality losses.

Component connection

E VCR E DVD E Blu-ray player/recorder You will enjoy accurate colour reproduction and high quality images through the EXT 8 terminal when connecting a DVD recorder or other recording equipment.
Component cable DVI/HDMI adapter cable HDMI cable 3.5 mm stereo minijack cable

R L Y PB (CB) PR (CR)

COMPONENT
DVI/HDMI conversion Using an DVI/HDMI adapter cable, the digital video signals of a DVD can also be played via the compatible HDMI connection. The sound must be fed in additionally. Both HDMI and DVI use the same HDCP copy protection method.

S-VIDEO/VIDEO connection

E VCR E DVD E Blu-ray player/recorder E Game console E Camcorder You can use the EXT 3 terminal when connecting to a game console, camcorder, a DVD recorder and some other equipment.
E After connecting HDMI Audio Select
After connecting, you must set the audio signal compatible with the cable you use for the HDMI device.
Go to MENU > Option > HDMI Audio Select Select Digital for audio signals via the HDMI terminal. Select Analogue for audio signals via the AUDIO jack (EXT6).

AV cable S-video cable

NOTE If a connected HDMI device is AQUOS LINK compatible, you can take advantage of versatile functions. (Pages 20 - 22) Video noise may occur depending on the type of HDMI cable used. Make sure to use certified HDMI cable. When playing the HDMI image, the best possible format for the picture will be detected and set automatically.
Supported video signal: 576i, 576p, 480i, 480p, 1080i, 720p, 1080p See page 36 for PC signal compatibility.
NOTE When using an S-video cable, you also need to connect an audio cable (R/L). EXT3: The S-VIDEO terminal has priority over the VIDEO terminal.

LC-3237X20E-gb.indd 16

2007/08/31 16:58:07

SCART connection

E Decoder

E VCR E DVD recorder

E When using the EXT 1 (SCART) terminal
E When using the EXT 2 (SCART) terminal
If your VCR supports TV-VCR advanced AV Link systems, you can connect the VCR using a fully wired SCART cable.

SCART cable SCART cable

SCART cable

Decoder

NOTE In cases when the decoder needs to receive a signal from the TV, make sure to select the appropriate input terminal to which the decoder is connected in Manual adjust in the Analogue Setting menu. (Page 27) TV-VCR advanced AV Link systems may not be compatible with some external sources. Do not connect the decoder to the EXT2 terminal. You cannot connect the VCR with Decoder using a fully wired SCART cable when selecting Y/C under the EXT2 in the Input Select menu.
Controlling devices with SCART using AV Link
This TV incorporates four typical AV Link functions for smooth connections between the TV and other audiovisual equipment. One Touch Play While the TV is in standby mode, it automatically turns on and plays back the image from the audiovisual source (e.g. VCR, DVD). TV Standby When the TV enters standby mode, the connected audiovisual equipment (e.g. VCR, DVD) enters standby mode as well. WYSIWYR (What You See Is What You Record) When the remote control unit of the connected VCR has the WYSIWYR button, you can automatically start recording by pressing the WYSIWYR button. Preset Download Automatically transfers the channel preset information from the tuner on the TV to the one on the connected audiovisual equipment (e.g. VCR) via the EXT 2 terminal.
NOTE Refer to the operation manuals of external equipment the details. Only works when the audiovisual equipment is connected to the EXT 2 terminal on the TV with AV Link via a fully wired SCART. The use of the AV Link function is only possible if the TV-set has enforced a complete auto installation with the connected audiovisual equipment. (Page 9, initial auto installation) The availability of the AV Link function depends on the audiovisual equipment used. Depending on the manufacturer and type of equipment used, it is possible that the described functions may be completely or partially unusable. 17

NOTE Refer to the operation manual of the device to be connected for further details. After unplugging connection cables or changing the connection pattern, first turn on the power of the TV with all relevant devices power turned on. Change the external input source by pressing b, select the appropriate external source and verify the audiovisual output. The cables illustrated in the following explanation are commercially available items.
Connecting an AQUOS BD Player/AQUOS Recorder via the AQUOS AUDIO speaker system
Connecting an AQUOS BD Player/AQUOS Recorder only
Optical AUDIO cable HDMI cable

HDMI cable HDMI cable

AQUOS BD Player/ AQUOS Recorder
AQUOS AUDIO speaker system

AQUOS LINK Setup

AQUOS LINK Auto power on
If this is activated, the One Touch Play function is enabled. While the TV is in standby mode, it automatically turns on and plays back the image from the HDMI source.
Repeat steps 1 to 3 in AQUOS LINK Auto power on. Press a/b to select Selecting Recorder, and then press OK. Select the recorder, and then press OK.
Press MENU and the menu screen displays. Press c/d to select Option. Press a/b to select AQUOS LINK Setup, and then press OK. Press a/b to select Auto Power On, and then press OK. Press c/d to select On, and then press OK.
NOTE If you have connected the AQUOS AUDIO speaker system between the TV and an AQUOS Recorder, the external sources indication changes from EXT5 to EXT5 (Sub).

Using Genre Info.

This function allows you to automatically switch to the appropriate sound mode depending on the genre information included the digital broadcast.
NOTE The factory default for this item is Off.
Repeat steps 1 to 3 in AQUOS LINK Auto power on. Press a/b to select Using Genre Info., and then press OK. Press c/d to select On, and then press OK.

Selecting recorder

Here, you can select a recorder for the recording from several connected recorders.

LC-3237X20E-gb.indd 21

2007/08/31 16:58:23
Operating an AQUOS LINK device
AQUOS LINK allows you to operate the HDMIconnected device with one remote control.
Playback of titles using AQUOS LINK
This section explains how to play back a title in the AQUOS BD Player/AQUOS Recorder.
Open the remote controls flip cover. Press PLAY I to start playback of a title.
See the right column, section Playback of titles using AQUOS LINK if you want to start playback using the list of the titles of the AQUOS BD Player/ AQUOS Recorder.
Open the remote controls flip cover. Press OPTION.
The AQUOS LINK Menu displays.
Press a/b to select Top Menu/Title List, and then press OK.
The linked recorder now powers on and the TV automatically selects the appropriate external input source. The title list data from the connected AQUOS BD Player/AQUOS Recorder displays.

Press FWD J to fast forward. Press REV G to reverse. Press STOP H to stop. Press B to turn the HDMI-connected device on/off.
Select the title with a/b/c/d, and then press PLAY I.
Listening with the AQUOS AUDIO speaker system
You can opt to listen to the TV sound only from the AQUOS AUDIO speaker system.
Selecting media type for CEC-compatible recorder
If your recorder has multiple storage media, select the media type here.
AQUOS LINK Menu Recorder EPG Top Menu/Title List Media change By AQUOS AUDIO SP By AQUOS SP Sound mode change Model select
Press a/b to select Media change, and then press OK. Select the desired medium, such as DVD or HDD. The media type changes every time you press OK.

HDMI device selection

If multiple HDMI devices are connected in a daisy chain, you can specify which device to control here.
Press a/b to select By AQUOS AUDIO SP, and then press OK.
The sound from the TV speaker and headphone terminal is silenced and only the sound from the AQUOS AUDIO speaker system is audible.
Listening with the AQUOS TV speaker system
You can opt to listen to the TV sound only from the AQUOS TV speaker system.
Press a/b to select Model select, and then press OK. The HDMI device changes every time you press OK.
Recording via the AQUOS Recorder EPG (only for recorders)
You can call up the CEC-compatible recorders EPG and preset timer recordings using the TVs remote control.
Press a/b to select By AQUOS SP, and then press OK.
Manually changing the AQUOS AUDIO speaker systems sound mode
Press a/b to select Recorder EPG, and then press OK.
The external input source switches and the recorders EPG is displayed.
Select the programme to record.
Refer to the operation manual of the recorder for details.
Press a/b to select Sound mode change. The sound mode changes every time you press OK.
Refer to the operation manual of the AQUOS AUDIO speaker system for details.

LC-3237X20E-gb.indd 22

2007/08/31 16:58:27

Menu operation

What is the Menu?
You need to bring up the On-Screen Display to perform settings for the TV. The On-Screen Display for the settings is called Menu. The Menu enables various settings and adjustments. The Menu can be operated with the remote control unit.

Common operations

Display the Menu Screen

Select an item

Press MENU and the MENU screen displays.

MENU [Picture]

Picture Audio
Press a/b/c/d to select/adjust the desired menu, and adjust the item to the desired level, and then press OK. Press 6 to return to the previous Menu page. E Selecting in the Menu

DYNAMIC

OPC Backlight Contrast Brightness Colour Tint Sharpness Advanced Reset [+14] [+30] [0] [0] [0] [0] [Off] +16 +40 +30 +30 +30 +10
[Power Control. No Operation Off]
Power Control No Signal Off No Operation Off Ecology Sleep Timer
Setup [Disable] [Disable]

Exit the Menu screen

E Selecting options
The operation will exit the menu screen if you press END before it is completed.
Digital Search Analogue Search
NOTE Menu options differ in the selected input modes, but the operating procedures are the same. The screens in the operation manual are for explanation purposes (some are enlarged, others cropped) and may vary slightly from the actual screens. Items with 4 cannot be selected for various reasons.
Operation without a remote control
This function is useful when there is no remote control within your reach.

About the Guide Display

The Guide Display at the bottom of the screen shows operations with an On-Screen Display.
Press MENU briefly to display the direct control screen. Press P r/s instead of a/b or i k/l instead of c/d to select the item. Press b to complete the setting.
The bar above is an operational guide for the remote control. The bar will change in accordance with each menu setting screen.
NOTE The direct control menu screen will disappear if left unattended for several seconds.

LC-3237X20E-gb.indd 23

Basic adjustment

Picture Settings

Picture

Advanced

This TV provides various advanced functions for optimising the picture quality.
[Off] [+14] [+30] [0] [0] [0] [0] +16 +40 +30 +30 +30 +10
Colour Temp. Film Mode Active Contrast 3D-Y/C Monochrome Range of OPC High Mid-High Middle Mid-Low Low
OPC Backlight Contrast Brightness Colour Tint Sharpness Advanced Reset

Colour Temp.

Automatically adjust the brightness of the screen.
Item Off: The brightness is fixed at the value set in Backlight. On: Automatically adjusts On:Display: Displays the OPC effect on the screen while adjusting the brightness of the screen. NOTE When set to On, the TV senses the surrounding light and automatically adjusts the backlight brightness. Make sure no object obstructs the OPC sensor, which could affect its ability to sense surrounding light.

Five minutes before the TV enters standby mode, the remaining time displays every minute.

Programme Setup

Digital Setting
You can reconfigure DTV services settings automatically or manually.

Ecology

When set to Yes the TV activates the following power saving mode.
OPC set to On (Page 24) Standby Mode set to Mode 2 (Page 32) No Signal Off set to Enable (Page 25) No Operation Off set to 3hr. (Page 26)

E Additional Search

Use this menu to add new services automatically after auto installation has been completed.

E Manual Search

Add new services within a specified frequency band.
Enter the frequency using 0 - 9 numeric buttons.

E Manual Adjust

Configure various settings for each service using the Colour (R, G, Y, B) buttons.
[Setup. Programme Setup. Digital Setting. Manual Adjust] Service No. DTV DTV DTV 999 Service Name SIT 3 SIT 2 SIT 1 Monosco 576-2 Monosco 576-1 Color Bar 576i HD Monosco

Sleep Timer

Allows you to set a time when the TV automatically switches to standby.
NOTE Select Off to cancel the sleep timer. When the time has been set, countdown automatically starts. Five minutes before the preset of time expires, the remaining time displays each minute.

CH Skip

EPG Skip

Old LCN

DTV DTV DTV DTV

: Lock

: CH Skip

: EPG Skip

: Sort
Channel Settings Auto Installation
Press a/b to select the desired service. Press the colour button on the remote control corresponding with the item you want to reconfigure.
The mark indicates the operation is set to on. Each time the colour button is pressed, you can switch the corresponding operation on/off.

Auto Installation

The TV automatically detects and stores all available services in your area. This function also allows you to perform the channel setting for Digital and Analogue individually and reconfigure the settings after the initial auto installation has been completed.
Buttons for Manual Adjust operation Lock: Press R button. When the service is locked, you must enter your PIN whenever you tune to the service. CH Skip: Press G button. Services with a mark are passed over when pressing Pr/s in the TV/remote control unit. EPG Skip: Press Y button. Services with a mark are passed over in the Electronic Programme Guide (EPG). Sort: Press B button. The item position of services can be sorted.

P H S W W W W W W W W W W W W I I I I I I I I I I I I D D D D D D D D D D D D T T T

D C C H C H U P

C H D W _ D D D INPUT SELECTION B I I I I I I I I I AV MODE SELECTION A A A A A A A A A A VOLUME T T T V D * _

D W _ 8 ? *

N P N P N P N P N P N P N P N P N P

M U M U M U

A C S U A C S U A C S U A C H A O O O O O O T T F F F F F F E E
V M D V M D V M D V M D V M D V M D V M D V M D V M D V M D L M
T M 0 T M 1 T M 2 T M 3 T M 4 T M 5 X X T T *

D C P G

LC-3237X20E-gb.indd 36

2007/08/31 16:58:49

Appendix

Troubleshooting

Problem No power. Possible Solution Check if you pressed B on the remote control unit. If the indicator on the TV lights up red, press B. Is the AC cord disconnected? Check if you pressed a on the TV. External influences such as lightning, static electricity, etc., may cause improper operation. In this case, operate the unit after first turning the power off, or unplugging the AC cord and re-plugging it in after 1 or 2 minutes. Are batteries inserted with polarity (e, f) aligned? Are batteries worn out? (Replace with new batteries.) Are you using it under strong or fluorescent lighting? Is a fluorescent light illuminated onto the remote control sensor?

Unit cannot be operated.

Remote control unit does not operate.

Picture is cut off.

Is the image position correct? Are screen mode adjustments (WIDE MODE) such as picture size made correctly? (Pages 29 and 33) Adjust the picture tone. Is the room too bright? The picture may look dark in a room that is too bright. Check the colour system setting. (Pages 27 and 32) The units internal temperature has increased. Remove any objects blocking the vent or clean. Is the sleep timer set? Select Off from the Sleep Timer menu. (Page 26) Is No signal off activated? Are connections to external equipment correct? (Pages 15-17) Is the input signal type selected correctly after connection? (Page 32) Is the correct input source selected? (Page 10) Is a non-compatible signal being input? (Page 36) Is the picture adjustment correct? (Pages 24-25) Is the antenna connected properly? (Page 8) Is On selected in Audio Only? (Page 30)

Strange colour, light colour, or dark, or colour misalignment. Power is suddenly turned off.

No picture.

No sound.
Is the volume too low? Make sure that headphones are not connected. Check if you pressed e on the remote control unit. This is not a malfunction. This happens when the cabinet slightly expands and contracts according to change in temperature. This does not affect the TVs performance.
The TV sometimes makes a cracking sound.
Cautions regarding use in high and low temperature environments
When the unit is used in a low temperature space (e.g. room, office), the picture may leave trails or appear slightly delayed. This is not a malfunction, and the unit will recover when the temperature returns to normal. Do not leave the unit in a hot or cold location. Also, do not leave the unit in a location exposed to direct sunlight or near a heater, as this may cause the cabinet to deform and the LCD panel to malfunction. Storage temperature: e5C to e35C.
Information on the software license for this product
Software composition The software included in this product is comprised of various software components whose individual copyrights are held by SHARP or by third parties. Software developed by SHARP and open source software The copyrights for the software components and various relevant documents included with this product that were developed or written by SHARP are owned by SHARP and are protected by the Copyright Act, international treaties, and other relevant laws. This product also makes use of freely distributed software and software components whose copyrights are held by third parties. These include software components covered by a GNU General Public License (hereafter GPL), a GNU Lesser General Public License (hereafter LGPL) or other license agreement. Obtaining source code Some of the open source software licensors require the distributor to provide the source code with the executable software components. GPL and LGPL include similar requirements. For information on obtaining the source code for the open source software and for obtaining the GPL, LGPL, and other license agreement information, visit the following website: http://www.sharp-eu.com/gpl/ We are unable to answer any questions about the source code for the open source software. The source code for the software components whose copyrights are held by SHARP is not distributed. Acknowledgements The following open source software components are included in this product: linux kernel modutils glibc zlib libpng

LC-3237X20E-gb.indd 37

2007/08/31 16:58:50
Updating your TV via DVB-T
To ensure that your TV software version is always up to date, from time to time SHARP will make updated TV base software and DVB software available. Digital Setup

Information

Receiver Report
Display reports regarding failures and changes for timer settings.

Download Setup

Searching for updates*
* The country except UK and Sweden is set to Yes on this function. The TV automatically determines whether a new software version is available when the TV is in standby mode.
Item Yes: Search automatically if there is software available for update when the TV is in standby mode. No: Do not search for update information. Now: Check whether or not there is a new software immediately. NOTE The TV must remain in standby mode for download. Do not switch off the TV with the main power switch. Updating the software may take some time.
If complex adjustments are made so that the settings cannot be restored to normal, you can reset the settings to the factory preset values. Setup

Reset 1 2

Press c/d to select Yes, and then press OK.
Now, TV will restart automatically. OK? displays on the screen.
Now initialising. displays on the screen and blinks. After the reset has completed, the power shuts off and then comes back on. The screen will have returned to its original settings.

Downloading the software

If the software is updated, the confirmation message New download information has been detected. appears. You can select the method of update.

Now initialising.

When you tune to the service that provides the update, a confirmation message displays. Follow the screen prompts.
Item Yes: Start downloading immediately. It takes approximately one hour to update. You cannot carry out other operations while downloading. No: Start downloading automatically several minutes after entering standby mode. The Timer settings will be executed. Cancel the download by pressing OK on the remote control when displaying Discontinue on the screen during the update.

Identification

You can check the TV ID on the screen for reporting to customer service.

CLEARING THE PASSWORD

Message List
When software is detected in the Download Setup menu and No is selected, you can update the software from the Message List menu. Press c/d to select Yes after confirming the message, and then press OK.
NOTE When the TV succeeds at downloading new software, the message is updated in the Message List of the Information menu. The software update will not be carried out if there is no new software available at the specified download time.
Go to MENU > Setup. Press a/b to select Auto Installation, Programme Setup, Child Lock, Reset, and the PIN input screen displays.
Press and hold both CH r and VOL k on the TV simultaneously until the message appears on the screen.

LC-3237X20E-gb.indd 38

Specifications
Item LCD panel Number of dots Video Colour System TV Function TV-Standard Receiving Channel Analogue Digital VHF/UHF CATV 32o LCD COLOUR TV, Model: LC-32X20E, LC-32X20S 32o Advanced Super View & BLACK TFT LCD 6,220,800 dots (1920 g 1080 g 3 dots) PAL/SECAM/NTSC 3.58/NTSC 4.43/PAL 60 CCIR (B/G, I, D/K, L/L) DVB-T (2K/8K OFDM) E2E69ch, F2F10ch, I21I69ch, IR AIR Jch (Digital: E5-E69ch) Hyper-band, S1S41ch Auto Preset 999 ch (ATV: 99 ch), Auto Label, Auto Sort NICAM/Acd/m2 60,000 hours (at Backlight Standard position) H : 176 V : 176 10W g 2 (40 mm g 100 mm) g 2 / 20 mm g 2 Antenna RS-232C EXT 1 EXT 2 EXT 3 EXT 4 EXT 5 EXT 6 EXT 7 EXT 8 DIGITAL AUDIO OUTPUT C. I. (Common Interface) OUTPUT Headphones OSD language UHF/VHF 75 q Din type (Analogue & Digital) D-Sub 9 pin male connector SCART (AV input, Y/C input, RGB input, TV output) SCART (AV input/monitor output, Y/C input, AV Link, RGB input) S-VIDEO (Y/C input), RCA pin (AV input) HDMI HDMI HDMI, 3.5 mm jack 15 pin mini D-sub, 3.5 mm jack COMPONENT IN: Y/Pb(Cb)/Pr(Cr), RCA pin (L/R) Optical SPDIF Digital audio output EN50221, R206001 RCA pin (Audio) 3.5mm jack (Audio output) Czech, Danish, Dutch, English, Estonian, Finnish, French, German, Greek, Hungarian, Italian, Latvian, Lithuanian, Norwegian, Polish, Portuguese, Russian, Slovak, Slovene, Spanish, Swedish, Turkish AC 220240 V, 50 Hz 132W (0.5 W Standby) (Method IEC60107) 15.0 kg (Without stand), 18.0 kg (With stand) 0C to k40C 170W (0.5 W Standby) (Method IEC60107) 18.0 kg (Without stand), 21.0 kg (With stand) 37o LCD COLOUR TV, Model: LC-37X20E, LC-37X20S 37o Advanced Super View & BLACK TFT LCD
TV-Tuning System STEREO/BILINGUAL Brightness Backlight life Viewing angles Audio amplifier Speaker Terminals
Power Requirement Power Consumption Weight Operating temperature
As a part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units. NOTE Refer to the inside back cover for dimensional drawings.

SHARP ELECTRONICS (Europe) GmbH
Sonninstrae 3, D-20097 Hamburg
Printed on environmentally friendly paper Auf kologischem Papier gedruckt Imprim sur papier cologique Stampato su carta ecologica Afgedrukt op ecologisch papier Impreso en papel ecolgico
Printed in Poland Gedruckt in Polen Imprim en Pologne Stampato in Polonia Gedrukt in Polen Impreso en Polonia

TINS-D198WJZZ

07P09-PL-NG

ESPAOL

SHARP CORPORATION
OPERATION MANUAL BEDIENUNGSANLEITUNG MODE DEMPLOI MANUALE DI ISTRUZIONI GEBRUIKSAANWIJZING MANUAL DE MANEJO

NEDERLANDS

LCD COLOUR TELEVISION LCD-FARBFERNSEHGERT TLVISEUR COULEUR CRAN CRISTAUX LIQUIDES (LCD) TELEVISORE A COLORI LCD LCD-KLEURENTELEVISIE TELEVISIN EN COLOR LCD

ITALIANO

FRANAIS
LC-32X20E LC-32X20S LC-37X20E LC-37X20S

DEUTSCH

ENGLISH
LC-32X20E/LC-37X20E LC-32X20S/LC-37X20S D198WJZZ OPERATION MANUAL / BEDIENUNGSANLEITUNG / MODE D'EMPLOI / MANUALE DI ISTRUZIONI / GEBRUIKSAANWIJZING / MANUAL DE MANEJO 1
) : LC-32X20E/LC-32X20S ] : LC-37X20E/LC-37X20S : LC-32X20E/LC-32X20S LC-37X20E/LC-37X20S
480.0 480,0 ( 776.0 ) / [ 898.0 ] ( 776,0 ) / [ 898,0 ] 99.0 99,0 94.6 94,6
( 701.5 ) / [ 824.4 ] ( 701,5 ) / [ 824,4 ] ( 572.0 ) / [ 638.0 ] ( 572,0 ) / [ 638,0 ] ( 517.0 ) / [ 581.0 ] ( 517,0 ) / [ 581,0 ] ( 396.0 ) / [ 464.0 ] ( 396,0 ) / [ 464,0 ]

(55.0) (55,0)

[57.0] [57,0]
( 332.0 ) / [ 369.0 ] ( 332,0 ) / [ 369,0 ]

300.0 300,0

276.0 276,0
SPECIAL NOTE FOR USERS IN THE U.K. The mains lead of this product is tted with a non-rewireable (moulded) plug incorporating a 13A fuse. Should the or and of the same rating as above, fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked which is also indicated on the pin face of the plug, must be used. Always ret the fuse cover after replacing the fuse. Never use the plug without the fuse cover tted. In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the mains plug and t an appropriate type.

( 130.0 ) ( 130,0 )

[ 156.7 ] [ 156,7 ]
DANGER: The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a safe manner. Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet, as a serious electric shock may occur. To t an appropriate plug to the mains lead, follow the instructions below: IMPORTANT: The wires in the mains lead are coloured in accordance with the following code: Blue: Neutral Brown: Live As the colours of the wires in the mains lead of this product may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured blue must be connected to the plug terminal which is marked N or coloured black. The wire which is coloured brown must be connected to the plug terminal which is marked L or coloured red. Ensure that neither the brown nor the blue wire is connected to the earth terminal in your three-pin plug. Before replacing the plug cover make sure that: If the new tted plug contains a fuse, its value is the same as that removed from the cut-off plug. The cord grip is clamped over the sheath of the mains lead, and not simply over the lead wires. IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.