The LCD panel is a very high technology product, giving you fine picture details. Due to the very large number of pixels, occasionally a few non-active pixels may appear on the screen as a fixed point of blue, green or red. This is within product specifications and does not constitute a fault.
Precautions when transporting the TV
When moving the TV, it should always be carried by two people, using both hands, be careful not to apply pressure to the display.

Trademarks

HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. The HD ready Logo is a trademark of EICTA. The DVB logo is the registered trademark of the Digital Video Broadcasting - DVB - project.

LC-37D44E-gb.indd 2

2008/06/16 13:38:05

Supplied accessories

Remote control unit (g1) AC cord (g1) Product shape varies in some countries. Cable clamp (g1) Stand unit (g1)
Pages 5 and 6 AA size battery (g2). Page 5

Page 4

Page 4 Operation manual (This publication)

Page 3

Quick guide

Attaching the stand

Before performing work spread cushioning over the base area to lay the TV on, making sure the area is completely flat. This will prevent it from being damaged. Before attaching (or detaching) stand, unplug the AC cord from the AC INPUT terminal.
Confirm the 10 screws supplied with the TV. Screws (m10)
1 Insert the stand into the opening on the bottom of the TV. 2 Insert and tighten the 4 screws on the rear of the TV as shown.
Attach the two parts of the stand unit to each other using the 6 screws as shown.
NOTE To detach the stand, perform the above steps in reverse order.

LC-37D44E-gb.indd 3

2008/06/16 13:38:06

Setting the TV

Standard DIN45325 plug (IEC 169-2) 75-ohm coaxial cable
Place the TV close to the AC outlet, and keep the power plug within reach.

Antenna

Connect the antenna cable from your antenna/cable socket or the (room-/roof) antenna for antenna input terminal on the back of your TV set to receive digitally/terrestrially broadcast stations. An indoor antenna can also be used under good reception conditions. Passive and active room antennas are offered commercially. In an active antenna its power is supplied via the antenna input terminal. The supply voltage (5V) must be correspondingly set under Supply Voltage. (See page 18.)
Product shape varies in some countries. AC cord

Bundling the cables

Bundle the cables with the clamp.

Cable clamp

Setting the TV on the wall
This TV should be mounted on the wall only with the wall mount bracket available from SHARP. (See page 35.) The use of other wall mount brackets may result in an unstable installation and may cause serious injuries. The centre of the TV screen is 6 mm above A engraved onto the metal plate angle used for affixing to a wall. Installing the LCD Colour TV requires special skill that should only be performed by qualified service personnel. Customers should not attempt to do the work themselves. SHARP bears no responsibility for improper mounting or mounting that results in accident or injury. You can ask a qualified service personnel about using an optional bracket to mount the TV to the wall.

14 SURROUND Switch the surround effects on and off. (See page 15.) 15 RADIO DTV: Switch between RADIO and DTV mode. 16 e (Mute) Switch the sound on and off.
E Using 2 on the remote control unit
DTV mode: Press 2 to open the multi audio screen. (See page 31.) Analogue TV mode: Each time you press 2, the mode switches as illustrated in the following tables.
NICAM TV broadcasts selection
Signal Stereo Bilingual Monaural Selectable items
NICAM STEREO, MONO NICAM CH A, NICAM CH B, NICAM CH AB, MONO NICAM MONO, MONO
17 DTV Press to access DTV mode while watching other input sources, and vice versa. (This button will not work if you were watching DTV immediately before turning off the TV. In this case first select any other input source except DTV using the b button.) 18 i (k/l) (Volume) i (k) Increase the volume. i (l) Decrease the volume. 19 P (r/s) TV/DTV: Select the channel. External: Switch to TV or DTV input mode. Teletext: Move to the next/previous page. 20 b (INPUT SOURCE) Select an input source. (TV, DTV, EXT1, EXT2, EXT3, EXT4, EXT5, EXT6, EXT7) (See page 9.) 21 SLEEP Set the sleep timer on (in units of 30 min. up to max. 2 hr. 30 min) and off. 22 p (Display information) (See pages 21, 29 and 30.) 23 DTV MENU DTV: Display DTV Menu screen. 24 MENU Display the MENU screen. (See page 11.) 25 OK Execute a command within the menu screen. TV/DTV: Display the programme list. (See pages 8 and 30.) 26 RETURN Return to the previous menu screen. (Subpage) (See page 21.) 28 [ (Subtitle for Teletext) TV/External: To turn the subtitles on and off. (See page 21.) DTV: Display the subtitle selection screen. (See page 31.) 29 Colour (Red/Green/Yellow/Blue) TELETEXT: Select a page. (See page 21.) DTV: The coloured buttons are used to select correspondingly to the coloured items in the menu screen.
A2 TV broadcasts selection
STEREO, MONO CH A, CH B, CH AB MONO
NOTE When no signal is input, the sound mode will display MONO.

LC-37D44E-gb.indd 6

2008/06/16 13:38:13

TV (Front view)

B (Standby/On) indicator

TV (Rear view)

i (l/k) (Volume buttons) a (Power button) MENU button b (Input Source) button
P (s/r) (Programme [channel] buttons)
RS-232C terminal EXT 4 (ANALOGUE RGB/AUDIO) terminals EXT 5 (COMPONENT) terminals EXT 1 (RGB) terminal EXT 2 (RGB) terminal Antenna input terminal (DVB-T 5V=/80 mA) 13 OUTPUT (AUDIO) terminals EXT 6 (HDMI/AUDIO) terminals EXT 7 (HDMI) terminal COMMON INTERFACE slot EXT 3 terminals Headphone jack AC INPUT terminal

WARNING: Make sure that the volume is turned down before using or connecting earphones and headphones. Listen to audio at moderate levels. Excessive sound pressure from earphones and headphones can cause hearing loss.
NOTE Only if you use an active terrestrial antenna, select On (5V) under Supply Voltage. (See page 18.)

LC-37D44E-gb.indd 7

2008/06/17 10:26:25

Turning on the power

Press a on the TV or B on the remote control unit.
Using the analogue programme list
You can also select the desired channel from programme list instead of using 0 - 9 numeric buttons or P (r/s).

Standby mode

Press B on the remote control unit when the TV is on.
The TV enters standby mode and the image on the screen disappears. The B indicator on the TV changes from green to red. To completely turn off the power to the TV, unplug the AC cord from the AC outlet. However, do not unplug the AC cord unless otherwise instructed.
Press OK when no other menu screen is displayed. (Except when an external input source is selected.) Press a/b to select the desired channel to tune in, and then press OK. Press END to exit the Programme List.

Display status indicator

Off Red Green Power off. The TV is in standby mode. The TV is on.
Initial auto installation (DTV)
Digital Video Broadcasting is a transmission scheme. It is much more than a simple replacement for existing analogue television transmission. DVB provides more stations, clearer picture quality and other services displayed on the screen. It also allows a range of new features and services including subtitles and multiple audio tracks. To watch DTV broadcasts, follow the procedures below to scan all available services in your area.
NOTE If you are not going to use this TV for a long period of time, be sure to remove the AC cord from the power outlet. Weak electric power is still consumed even when a is turned off. In DTV input mode, if the power is turned off immediately after a setting change from the menu screen, the new setting or channel information may not be memorised.
Initial auto installation (Analogue)
When the TV is powered on for the first time after purchase, the initial auto installation (Analogue) is invoked. You can automatically set language, country and channels in successive operations.
NOTE The initial auto installation functions only once. If the initial auto installation is not completed (ex: When menu screen disappeared by not operating for a few minutes, when the power shut down, etc.), try Auto Installation from the Setup menu. (See page 15.) The initial auto installation stops by pressing RETURN.
Press DTV or b to access the DTV mode. Press DTV MENU and the DTV Menu screen displays. Press c/d to select Installation. Press a/b to select Auto Installation, and then press OK. If you have already set the PIN, enter it here. If not, enter the factory preset PIN 1234.

See page 17 for setting PIN. A confirmation message displays. Press c/d to select Yes, and then press OK to start the search.
The TV starts scanning all available DTV and radio services in your area.
1 Press a/b/c/d to select the desired language listed on the screen. 2 Press OK to enter the setting. 1 Press a/b/c/d to select your country or area listed on the screen. 2 Press OK to enter the setting. The programme auto search starts at the same time.
Setting the on-screen display language
Setting the country or area
After this setting, auto search starts with the following order:
Programme auto search Auto labelling Auto sorting Preset download
NOTE The language and country settings used in this operation are the settings you have already set while executing the Initial auto installation (Analogue). If you want to reconfigure the country setting, for instance after moving to another country, conduct Auto Installation from the Setup menu again. The services are stored according to the channel number information embedded in the stream (if available). If the information is not available, the services are stored according to the order in which they were received. If you would like to sort the order, it is possible to arrange it as explained in page 24. To cancel the scan in progress, press END. You cannot select any DTV-related menu items unless Auto Installation has been completed.
You do not need to do anything during the auto search.
The setup menu disappears and you can watch the programme on channel 1.

LC-37D44E-gb.indd 8

2008/06/16 13:38:16

Using external equipment

Setting the input source
To view external source images, select the input source using b on the remote control unit or the TV.
NOTE The cables marked with * are commercially available items.

Connecting a VCR

You can use the EXT 1 or 2 terminals when connecting a VCR and other audiovisual equipment. If your VCR supports TV-VCR advanced AV Link systems, you can connect the VCR to the EXT 2 terminal of the TV using the fully-wired SCART cable.

Erase Programme

An individual programme can be erased.
NOTE As a precautionary measure, make a note of your PIN on the back of this operation manual, cut it out and keep it in a safe place that children cannot reach. See page 32 for resetting the current PIN to the factory preset 1234 if you lose or forget your PIN.
Repeat steps 1 to 4 in Programme Setup. Press c/d to select Yes, and then press OK. Press a/b/c/d to select the channel you want to erase, and then press OK.
A message screen pops up.

Input Label

You can assign each input source a label you like.
Press c/d to select Yes, and then press OK to erase the selected programme. All the subsequent programmes move up. Repeat steps 3 and 4 until all desired channels are erased.
Press b to select the desired input source. Press MENU and the MENU screen displays. Press c/d to select Setup. Press a/b to select Input Label, and then press OK. Press a/b/c/d to select each character of the new name for the input source, and then press OK. Repeat step 5 above until the name is fully spelt out, and then press OK.
The name can be 6 characters or less. If a label name is less than 6 characters, select END, then press OK.

Child Lock

Allow you to use a PIN to protect certain settings from being accidentally changed.

Changing the PIN

Press MENU and the MENU screen displays. Press c/d to select Setup. Press a/b to select Child Lock, and then press OK.

Change PIN Reset

NOTE You cannot change the label if the input source is TV or DTV.

New PIN

Reconfirm

LC-37D44E-gb.indd 17

Position

XGA Mode

Menu Operation: C (page 12) For adjusting a pictures horizontal and vertical position.
Item H-Pos.: Centres the image by moving it to the left or right. V-Pos.: Centres the image by moving it up or down. NOTE Adjustments are stored separately according to input source. Depending on the input signal type a position setting may not be available.
Menu Operation: C (page 12) You can select one of the 3 input signals listed below to adjust the picture resolution when the PC input is an XGA signal.

1024 g g g 768

NOTE Depending on the graphics card, resolutions of 1360 g 768 may not display correctly.

WSS (Wide Screen Signalling)

Language

Menu Operation: A (page 12) You can select a language from the Setup menu. Select desired language listed on the screen.
Menu Operation: A (page 12) WSS allows a television to switch automatically among the different screen formats.
NOTE Use WIDE MODE if an image does not switch to the correct screen format. When the broadcast signal contains no WSS information, the function will not work even if enabled. (See page 20.)

Supply Voltage

4:3 Mode
Menu Operation: A (page 12) Switch on or off the power to the antenna connected to the antenna input terminal. (See page 4.)
Menu Operation: A (page 12) The WSS signal has 4:3 auto-switching that allows you to select between Normal and Panorama.
Item Normal: Normal range keeping 4:3 or 16:9 aspect ratio Panorama: Wide image without side bars

Option menu

[Option] Option Audio Only DNR Input Select [Off] [CVBS] [AUTO]
WSS signal 4:3 screen 4:3 mode Normal 4:3 mode Panorama

Colour System

NOTE HDMI Setup is displayed only when EXT6 or EXT7 is selected from the INPUT SOURCE menu.

Audio Only

Menu Operation: A (page 12) When listening to music from a music programme, you can set the TV off and enjoy audio only.
Item Off: Both screen images and audio are output. On: Audio is output without screen image.

Fine Sync.

Menu Operation: C (page 12) Ordinarily, the TV automatically adjusts image positions coming from PC (Auto Sync. function). In some cases, however, manual adjustment is needed to optimise the image.
Item H-Pos.: Centres the image by moving it to the left or right. V-Pos.: Centres the image by moving it up or down. Clock: Adjusts when the image flickers with vertical stripes. Phase: Adjusts when characters have low contrast or when the image flickers. NOTE If you need to adjust the image position, adjust the position using your PC. 18

LC-37D44E-gb.indd 18

2008/06/16 13:38:27
DNR (Digital Noise Reduction)

Input Select

Menu Operation: A (page 12) For setting the signal type of external equipment.
Menu Operation: A (page 12) Produce a clearer image. (Off, High, Low)

HDMI Setup

AV only

Input source EXT 1 EXT 2

Signal type Y/C, CVBS, RGB Y/C, CVBS, RGB
HDMI (High-Definition Multimedia Interface) terminal selection.
To watch an HDMI equipment image, select EXT6 or EXT7 (the terminal which you are using) from INPUT SOURCE menu using b on the remote control unit or TV. Press MENU and the MENU screen displays. Press c/d to select Option. Press a/b to select HDMI Setup, and then press OK.

Press f.

The WIDE MODE menu displays.
Press f or a/b to select a desired item on the menu.
NOTE Connect the PC before making adjustments. (See page 10.) Selectable picture size may vary with input signal type.

EXAMPLE

Normal

Manual Selection

The WIDE MODE menu displays. The menu lists the wide mode options selectable for the type of video signal currently received.
Item Normal: Keeps the original aspect ratio in a full screen display. Full: An image fully fills the screen.
Press f or a/b while the WIDE MODE menu displays on the screen.
As you toggle down the options, each is immediately reflected on the screen. No need to press OK.

Auto Selection

If you set WSS and 4:3 Mode in the Setup menu on page 18, the optimum WIDE MODE is automatically chosen for every broadcast, VCR or DVD containing the WSS information.

WSS menu

To enable Auto Selection, set WSS in the Setup menu to On. (See page 18.)

4:3 Mode menu

To set the type of the wide screen, select Normal or Panorama in the 4:3 Mode menu. (See page 18.)

4:3 Mode set to Normal

4:3 Mode set to Panorama
NOTE If the signal contains no WSS information, Auto Selection will not function even when the WSS option is enabled.

LC-37D44E-gb.indd 20

Still image
You can freeze a motion picture on the screen.

Time display

You can display the time information included in the DTV and Teletext broadcasts.
NOTE Skip step 1 if receiving DTV broadcasts.
Press 3. Press 3 again to exit still image.
NOTE When this function is not available, No still image display available. will display. The still image automatically goes out after 30 minutes.
Select a TV channel providing Teletext information. (The time information is automatically captured.) Press p. The channel display will appear on the TV. Press p again within the several seconds that the channel display is on the screen. Time information will display below the channel display for several seconds. Even when you change the TV channel, you can display the time information with steps 2 and 3 above.

Teletext function

What is Teletext?
Teletext broadcasts pages of information and entertainment to specially equipped television sets. Your TV receives Teletext signals broadcast by a TV network, and decodes them into graphical format for viewing. News, weather and sports information, stock exchange prices and programme previews are among the many services available.

[: m: : Press to display the subtitle selection screen. Press to display TELETEXT or start the MHEG5 presentation, if available. Aside from direct channel entry, each of the numeric buttons have a unique function assigned in the Programme Setup screen. Press to access DTV mode. Press to open the EPG screen. Press to open the ESG screen. Press to switch between TV and RADIO mode. Due to the large variation in transmitted volume levels in RADIO mode, some stations will produce distortion if the volume level is set too high. Press to open the multi audio screen. Press to open or close the DTV Menu screen. Press to open the service banner or view detailed information from the EPG/ESG screen. Press to select a desired item on the screen or adjust a selected item. Press to go to the next step or complete the setting. Press to open the Programme List when no other menu screen is active. (Except when an external input source is selected.) END: Colour: RETURN: Press to exit the current menu screen without saving the changes. Each of the coloured buttons have a unique function assigned in the menu screen. Press to return to the previous step.
To configure various settings for each service. These include: Fav(ourite), Lock, Move, Move To, Skip, Select, Erase, Label, and View functions.

Installation

To scan all services available in your area, or to label/ erase/re-scan the selected carrier.

System Setup

To configure On-Screen Display and Child Lock settings.

DTV: EPG: ESG: RADIO:

Accessories
To display the current version of the software or to allow the software upgrade to take place.

Common Interface

To display the current Common Interface details.

Navigation buttons

To navigate within the DTV Menu screen.

2: DTV MENU: p:

DTV common operations
DTV common menu operation
3 Press DTV or b to access the DTV mode. Press DTV MENU and the DTV Menu screen displays. Press c/d to select the desired menu, and then press OK if necessary.
From this point, menu operations differ depending on the item you are going to adjust. See the respective section of the menu operation. You cannot select any DTV-related menu items unless Auto Installation has been completed. Press RADIO to switch between DTV and Radio mode. To exit the current screen without saving the change, press END.

a/b/c/d: OK:

LC-37D44E-gb.indd 22

2008/06/16 13:38:32

About using the character set screen
In some cases you may be prompted to enter characters. See below for details. Sample Alpha Numerical Character Set screen

Use space to add a space or overwrite.

1. 3. 5. 7. 9.

Fav Move Skip Erase View

2. 4. 6. 8.

Lock Move To Select Label

TV/Radio

To register the new name, press YELLOW (Select) to move the cursor back to the input area. Press OK.
A confirmation message displays.
NOTE The picture window shows a blank image if Radio services are listed.
Press c/d to select Yes, and then press OK.

LC-37D44E-gb.indd 23

2008/06/16 13:38:36
DTV menu operations Favourite
Assign services to 4 different favourite groups.

EXAMPLE:

Moving 002 ZDF ahead of 001 ARD. Default order: Press a/b to select the desired service in 001rs002rs003rs004. Sorted order: Press a/b to select the desired service in 002rs001rs003rs004.
ARD ZDF SAT. 1 RTL 002 ZDF ARD SAT. 1 RTL
Press a/b to select the desired service. Press on the remote control. A selection box displays. Press a/b to register the selected service to any of the 4 favourite groups (None, Fav 1. Fav 4) and then press OK. An icon displays indicating the favourite status.
Do not press END to exit the screen here if you wish to register the change.

Move To

Use this function to change the position of two selected services.
Press OK. Now you can easily select your favourite service from the Programme List. (See page 30.)
NOTE You cannot register the same service to two different favourite groups.
Press a/b to select the desired service. Press on the remote control. Enter the number you want to change to using numeric buttons, and then press OK. The positions of the selected services are switched.
Do not press END to exit the screen here if you wish to register the change. You cannot enter a service number that is not listed.
When the service is locked, you must enter your PIN whenever you tune to the service.
Press a/b to select the desired service. on the remote control. Press If you have already set the PIN, enter it here. If not, enter the factory preset PIN 1234. An icon displays indicating the service is locked.
Pressing will turn the lock icon on and off. (PIN entry is required when lifting the lock icon.) Do not press END to exit the screen here if you wish to register the change.
Press OK again, the message Successfully updated displays. The change is now registered.
ZDF ARD SAT. 1 RTL 001 RTL ARD SAT. 1 ZDF
Services that are set to skip will not be picked up when pressing P (r/s).

Press OK.

NOTE See page 17 for setting the PIN.
Press a/b to select the desired service. on the remote control. An icon Press displays indicating the service to be skipped.
Pressing will turn the skip icon on and off. Do not press END to exit the screen here if you wish to register the change.
Sort the order of the selected service by moving the service position.

Press a/b/c/d to access the desired service or event.
NOTE This function cannot be set for locked services or when Child Lock applies. (See pages 24 and 27.) Up to 8 events can be preset using the Timer function. If you are watching another event, an alarm message displays on the screen a few seconds before the preset time. An alert message displays when the preset events overlap one another. The TV power may not come on for several seconds if you preset an event using the EPG Timer and if the AC cord has been disconnected. When you set the EPG Timer, the power consumption during the standby mode will be higher (33 W or more) than normal. When the TV is turned off, the EPG Timer will not operate.
When using the EPG Timer for recording:
Make sure to set the timer of your recording equipment as well. Do not switch channels while recording. If the TV is in standby mode when the preset on-air time nears, it will output signals for recording without displaying images on the screen.

LC-37D44E-gb.indd 29

2008/06/16 13:38:45

Using the ESG

The Electronic Service Guide (ESG) is a simplified version of EPG, giving you only essential information of current events for faster access.

Viewing a service banner

A service banner shows event names, start/end time of event, and other useful information.

Press p.

Press ESG.

The ESG screen displays.

ESG 070 BBC News The Bold and Beautiful Current Event The Bold and Beautiful *** *** *** Page l Select

OK DTV MENU i+

Service banner
07:00 07:30 Services BBC News BBC 1 BBC 2 CBBC Channel
BBC 1 07:00 08:00 Business news

07:45 04/11/2005 MHEG

Page k

END RADIO

1 Press a/b to select a desired service, and then press OK.
The TV will show the image in full screen.
Logical channel number Service name Carrier name Favourite type Teletext available Subtitle available Lock status Scrambled service Multi audio status Current event name Current date and time MHEG5 service available To display more detailed information, press p again.
You can verify the signal strength and quality of the selected service here.
NOTE Basic operation procedures are similar to EPG operations. ESG does not provide information about future events, or access to Timer function.
Using the digital programme list
Select services by using the Programme List instead of numeric buttons or P (r/s). using
Press OK when no other menu screen is displayed. (Except when an external input source is selected.)
Programme List Fav Type S.No Services CBBC Channel BBC News BBC 1 BBC 2 Canal + UK Gold Carrier Freq FFT GI QAM BBC 538000 kHz 8K 1/All
Currently tuned service Service shown in picture window
The screen shows the service list in either TV or Radio mode sorted by favourite type (All, Fav 1 - 4) as configured in page 24. Press a/b to select the desired service, and then press OK.

Unit cannot be operated.

Remote control unit does not operate.

Picture is cut off.

Is the image position correct? (See page 18.) Are screen mode adjustments (4:3 Mode/WSS) such as picture size made correctly? (See pages 18 and 20.) Adjust the picture tone. (See pages 13 and 14.) Is the room too bright? The picture may look dark in a room that is too bright. Check the colour system setting. (See pages 16 and 19.) Check the HDMI Setup setting. (See page 19.)
Strange colour, light colour, or dark, or colour misalignment.
Power is suddenly turned off.
The units internal temperature has increased. Remove any objects blocking vent or clean. Check the power control setting. (See page 15.) Is sleep timer set? Press SLEEP on the remote control unit until it sets to Off. Is connection to other components correct? (See pages 9 and 10.) Is input signal type selected correctly after connection? (See page 19.) Is the correct input source selected? (See page 9.) Is non-compatible signal being input? (See page 33.) Is picture adjustment correct? (See pages 13 and 14.) Is the antenna connected properly? (See page 4.) Is On selected in Audio Only? (See page 18.)

No picture.

No sound.
Is the volume too low? (See pages 6 and 7.) Make sure that headphones are not connected. (See page 7.) Check if you pressed e on the remote control unit. (See page 6.) Check if Monochrome is set to On. If so, set it to Off. (See page 14.)
The DTV menu screen is displayed in monochrome and hard to select the item. The TV sometimes makes a cracking sound.
This is not a malfunction. This happens when the cabinet slightly expands and contracts according to change in temperature. This does not affect the TVs performance.
Cautions regarding use in high and low temperature environments
When the unit is used in a low temperature space (e.g. room, office), the picture may leave trails or appear slightly delayed. This is not a malfunction, and the unit will recover when the temperature returns to normal. Do not leave the unit in a hot or cold location. Also, do not leave the unit in a location exposed to direct sunlight or near a heater, as this may cause the cabinet to deform and the LCD panel to malfunction. Storage temperature: l20C to e60C.
IMPORTANT NOTE ON RESETTING THE PIN
We suggest that you remove the following instruction from the operation manual to prevent children from reading it. As this operation manual is multilingual, we also suggest the same with each language. Keep it in a safe space for future reference.
Repeat steps 1 to 3 in Changing the PIN. (See page 17.) Enter 3001 to cancel out the current PIN.
The PIN resets to the factory preset 1234.

LC-37D44E-gb.indd 32

2008/06/16 13:38:49

PC compatibility chart

Resolution VGA SVGA XGA WXGA WXGA 640 g g g g g 768 Horizontal Frequency 31.5 kHz 37.9 kHz 48.4 kHz 47.7 kHz 47.7 kHz Vertical Frequency 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz VESA Standard

Appendix Commands
CONTROL ITEM POWER SETTING INPUT SELECTION A COMMAND P O W R I I I I I CHANNEL T T D A A G D V T V V D V D D PARAMETER 0 _ _ _ * ? * ? _ _ _ _ _ _ ? * ? _ _ * _ _ _ _ _ ? _ ? _ _ * _ _ _ _ _ ? _ ? _ _ _ CONTROL CONTENTS POWER OFF INPUT SWITCHING (Toggle) TV (CHANNEL FIXED) DTV (CHANNEL FIXED) EXT(1 7) 1 to 7, ERR (TV/DTV) TV DIRECT CHANNEL (1 99) 1 to 99 CHANNEL UP CHANNEL DOWN THREE DIGIT DTV DIRECT CHANNEL (1999) *User for LC-37D44E FOUR DIGIT DTV DIRECT CHANNEL (19999) *User for LC-37D44S 1 to 999 *User for LC-37D44E 1 to 9999 *User for LC-37D44S DTV CHANNEL UP DTV CHANNEL DOWN EXT1 (Y/C) EXT1 (CVBS) EXT1 (RGB) 0 to 2 EXT2 (Y/C) EXT2 (CVBS) EXT2 (RGB) 0 to 2 EXT3 EXT4 EXT5 (COMPONENT) EXT6 (HDMI) EXT7 (HDMI) AV MODE SELECTION (Toggle) STANDARD SOFT ECO USER DYNAMIC 1 to 5 VOLUME (0 60) 0 to 60 TEXT SLEEP TIMER O O O O O O O T T T F F F F F F F E E E T M 0 T M 1 T M 2 T M 3 T M 4 T M 5 T M ? X X X T T T ? * ? _ _ _ _ _ _ ? _ _ ? * ? _ _ _ _ _ _ ? _ _ ? * ? _ _ _ _ _ _ ? _ _ ? _ ? AUDIO CHANGE SURROUND MUTE WIDE MODE CONTROL ITEM POSITION COMMAND H P O S H P O S V V C C P O S P O S L L C K C K E E E E E E E E E E E E E E E E V V V V PARAMETER * ? * ? * ? * ? 1 ? 2 ? 2 ? _ * ? * ? * ? * ? _ _ _ _ _ _ _ _ 0 ? _ _ _ ? _ _ _ ? _ * ? * ? * ? _ ? _ _ _ _ _ _ _ _ _ ? _ _ _ ? _ _ _ ? _ _ ? _ ? _ ? _ ? _ _ _ _ _ _ _ _ _ ? _ _ _ ? _ _ _ ? _ CONTROL CONTENTS H-POSITION AV (f10 e10) AV (f10 e10) V-POSITION AV (f10 e10) AV (f10 e10) CLOCK (0 - 180) 0 to 180 PHASE (0 64) 0 to 64 WIDE MODE (Toggle) NORMAL (AV) ZOOM 14:9 (AV) PANORAMA (AV) FULL (AV) CINEMA 16:9 (AV) CINEMA 14:9 (AV) NORMAL (PC) FULL (PC) 1 to 10 MUTE (Toggle) MUTE ON MUTE OFF 1 to 2 SURROUND (Toggle) SURROUND ON SURROUND OFF 1 to 2 SOUND SELECT (ST/Bilingual/ mono) OFF 30 m 1 h 00 m 1 h 30 m 2 h 00 m 2 h 30 m 0 to 150 TEXT OFF TEXT CHANGE (Toggle) 0 to 1 DIRECT PAGE JUMP (100 899) 100 to 899

D C C H D C C H C H U P

P H S P H S W W W W W W W W W W I I I I I I I I I I D D D D D D D D D D T T T T

C H D W _ D T V D *

D D D INPUT SELECTION B I I I I I I I I I I I I I AV MODE SELECTION A A A A A A A VOLUME