1 Menu Scrambled stations Description Specifies if you need to add pay-TV services. Selectable items Yes, No Channel: Extracts all of information from a channel (quick, but needs corresponding TV stations). Frequency: Checks every frequency in range (slow). From 47.0_858.0 MHz Specifies the network. Set this to register only the specified network ID without registering any special services. The symbol rates are specified by the cable provider. Input the value received for CATV. The symbol rates are specified by the cable provider. Input the value received for CATV.
Press a/b to select the menu, and then press ;.

[Yes] [Channel] [None]

Scrambled stations Search method Start frequency Network ID Symbol rate 1 Symbol rate 2 QAM modulation 1 QAM modulation 2 Reset Search start

Search method

Specifies how you search channels.

Start frequency

Network ID

None, 0_65535

Press a/b/c/d or 0_9 to select or input the appropriate item/value, and then press ;. 3 Press a/b to select Search start, and then press ;. 4 The TV searches for, sorts and stores all the receivable TV stations according to their settings and the connected antenna.
2 To abort the initial auto installation in progress, press 6.

Symbol rate 1*

1000_9000
The Scrambled stations menu and the Search method menu are not displayed on the screen as each menu item is fixed. The value of Start frequency and Network ID should be set to the value specified by the cable provider. *

Symbol rate 2*

QAM modulation 1 QAM modulation 2
16, 32, 64, 128, 256 None, 16, 32, 64, 128, 256
Set up Symbol rate 2 if the cable provider uses several symbol rates.
When you set Sweden in the country setting and select Cable for the searching format, you can select the cable provider ComHem. Follow the screen prompts.
Analogue broadcast setting

LC-LE705E_GB.indd 10

2009/10/09 14:12:58
Checking signal strength and channel strength (DVB-T/C)
If you install a DVB-T/C antenna for the first time or relocate it, you should adjust the alignment of the antenna to receive a good reception while checking the antenna setup screen. Channel strength of DVB-T
Supply voltage Signal strength Channel strength CH no. Signal strength Current Quality Current Max. Max. MHz
Go to MENU > Setup > Antenna setupDIGITAL.
E Checking signal strength
Press a/b to select Signal strength, and then press ;.
Supply voltage Signal strength Channel strength CH no. Signal strength Current Quality Current Max. Max.
Channel strength of DVB-C
Supply voltage Signal strength Channel strength Frequency Symbol rate QAM modulation Signal strength Current Quality Current Max. Max. MHz

Many stations use the TOP operating system, while some use FLOF (e.g., CNN). Your TV supports both these systems. The pages are divided into topic groups and topics. After switching on the teletext, up to 2,000 pages are stored for fast access. If you select a programme with no teletext signal, No Teletext available displays. The same message displays during other modes if no teletext signal is available.
[ (Subtitle for teletext)

Reveal or hide subpages.

TELETEXT

1 (Subpage)

Each time you press m, the screen switches as shown above. Press m again to display the teletext on the right screen and the normal image on the left screen.
Using the MHEG-5 application (UK only)
Some services bring you programmes with the MHEG application encoded, letting you experience DTV interactively. When provided, the MHEG-5 application will start when you press m.
Teletext will not work if the selected signal type is RGB (Page 34).

LC-LE705E_GB.indd 15

2009/10/09 14:13:02
Connecting external devices

E Before connecting.

Be sure to turn off the TV and any devices before making any connections. Firmly connect a cable to a terminal or terminals. Carefully read the operation manual of each external device for possible connection types. This also helps you get the best possible audiovisual quality to maximise the potential of the TV and the connected device. Refer to page 37 for connecting a PC to the TV.
The cables illustrated in pages 16_18 are commercially available items.
Video connections HDMI connection
Example of connectable devices
E DVD player/recorder E Blu-ray player/recorder E Game console The HDMI connections permit digital video and audio transmission via a connection cable from a player/recorder. The digital picture and sound data are transmitted without data compression and therefore lose none of their quality. Analogue/digital conversion is no longer necessary in the connected devices, which also would result in quality losses.

DVI/HDMI conversion

Using a DVI/HDMI cable, the digital video signals of a DVD can also be played via the compatible HDMI connection. The sound must be fed in additionally.

MENU options differ in the selected input modes, but the operating procedures are the same. Items with 4 cannot be selected for various reasons. The MENU screen will disappear if left unattended for several seconds.
Operation without a remote control unit
This function is useful when there is no remote control unit within your reach.
Press @ and the MENU screen displays. Press :r/s instead of a/b or i+/- instead of c/d to select the item. Press b to complete the setting.

About the guide display

The guide display at the bottom of the screen shows operations with the OSD.
The bar above is an operational guide for the remote control unit. The bar will change in accordance with each menu setting screen.

Select Enter Back End

LC-LE705E_GB.indd 22

Basic adjustment

Picture settings

Advanced

OPC Backlight Contrast Brightness Colour Tint Sharpness Advanced Reset
This TV provides various advanced functions for optimising the picture quality.
C.M.S.-hue C.M.S.-saturation C.M.S.-value Colour temp. 100 Hz Film mode Active contrast Gamma adjustment DNR 3D-Y/C Monochrome Range of OPC R Y G C B M
Automatically adjusts the brightness of the screen.
Item Off On On:Display The brightness is fixed at the value set in Backlight. Automatically adjusts. Displays the OPC effect on the screen while adjusting the brightness of the screen.

C.M.S.-hue

This function adjusts the hue of a selected colour using a six-colour adjustment system.

C.M.S.-saturation

This function increases or decreases the saturation of a selected colour using a six-colour adjustment system.
When set to On, the TV senses the surrounding light and automatically adjusts the backlight brightness. Make sure no object obstructs the OPC sensor, which could affect its ability to sense surrounding light.

C.M.S.-value

This function adjusts the brightness of a selected colour using a six-colour adjustment system.

Colour temp.

Adjusts the colour temperature to give the best white image.
Item High Mid-High c (Cursor) d (Cursor) Middle The screen brightens For more contrast For more brightness For more colour intensity Skin tones become greenish For more sharpness Mid-Low Low R/G/B Gain (LO), R/G/B Gain (HI) White with bluish tone. Intermediate tone between High and Middle. Natural tone. Intermediate tone between Middle and Low. White with reddish tone. Adjusts the white balance by changing the value of each item.

Picture adjustments

Adjusts the picture to your preference with the following picture settings.

Adjustment items

Selectable items Backlight Contrast Brightness Colour Tint Sharpness

The screen dims For less contrast For less brightness For less colour intensity Skin tones become purplish For less sharpness

LC-LE705E_GB.indd 23

2009/10/09 14:13:07

100 Hz

100 Hz technology provides superior solutions for digital display picture quality removing motion blur.

Range of OPC

The brightness level range of the OPC sensors automatic adjustments can be set according to your preferences. The adjustment range of the OPC sensor can be set to a maximum of e 16 and a minimum of f 16.
This effect is greater on fast moving images. 100 Hz will have no effect in the following cases. 1) The type of signal received is a PC signal. 2) An OSD is being displayed. 3) Teletext is activated. If images appear blurred, set the 100 Hz to Off.
This function is available only when the OPC setting is set to On or On:Display. The maximum setting cannot be set to a smaller number than the minimum setting. The minimum setting cannot be set to a bigger number than the maximum setting. The maximum and minimum settings cannot be set to the same number. Depending on the brightness of the surrounding light, the OPC sensor might not operate if the adjustment range is small.

Film mode

Automatically detects a film-based source (originally encoded at 24 or 25 frames per second, depending on the vertical frequency), analyses it and then recreates each still film frame for high-definition picture quality (Advanced (High), Advanced (Low), Standard, Off).

AV MODE

AV MODE gives you several viewing options to choose from to best match the system environment, which can vary due to factors like room-brightness, type of programme watched or the type of image input from external equipment.

Active contrast

Automatically adjusts the contrast of an image according to the scene.

Gamma adjustment

Selects the tone difference of the brightness and darkness of the image according to the type of programme watched from a maximum of e 2 to a minimum of f 2.
Press #. Each time you press #, the mode changes.
You can also switch the mode on the Picture and Audio menu screen by pressing #. Item
DNR produces a clearer image (Off, High, Middle, Low, Auto).
STANDARD MOVIE GAME PC* USER
For a highly defined image in a normally bright room. For viewing a movie in a darkened room. For playing of video games. For PC. Allows you to customise settings as desired. You can set the mode for each input source. For a clear-cut image emphasising high contrast for sports viewing (the Picture and Audio settings cannot be adjusted). For a clear-cut image emphasising high contrast for sports viewing. The TV automatically sets the appropriate selection from the AV MODE menu depending on the lighting conditions and the type of programme watched.

This function may not be available depending on the input signal type.

3D-Y/C

DYNAMIC (Fixed)
Provides high quality images with minimal dot crawl and cross colour noise by detecting changes in the image.
Item Standard Fast Slow Normal adjustment. Sets the optimum image quality for fastmoving images. Sets the optimum image quality for slow-moving images. AUTO DYNAMIC

NOTE NOTE

3D-Y/C may not operate depending on the input signal type or when the input signal is noisy. 3D-Y/C has even more effect on composite video signals (CVBS). The item marked with * is available only when selecting HDMI 1, HDMI 2, HDMI 3, HDMI 4 or EXT 4 from the INPUT SOURCE menu. If you select AUTO, some selections in the AV MODE menu may not be automatically set.

Monochrome

For viewing a video in black & white.

LC-LE705E_GB.indd 24

Audio settings

Emphasising dialogue

Option
Treble Bass Balance Surround Bass enhancer Reset L30 R30 [Off]

Clear voice

This function emphasises speech against background noise for greater clarity.

Outputting audio only

Audio adjustment
You can adjust the sound quality to your preference with the following settings.
Selectable items Treble Bass Balance c (Cursor) For weaker treble For weaker bass Decrease audio from the right speaker d (Cursor) For stronger treble For stronger bass Decrease audio from the left speaker

Audio only

When listening to music from a music programme, you can set the TV off and enjoy audio only.
Item Off On Both screen images and audio are output. Audio is output without a screen image.

Setting audio input

Surround
This function allows you to enjoy realistic live sound.

PC audio select

When using the EXT 4 terminal or HDMI 2 terminal, you must select which terminal uses the AUDIO (R/L) jack for analogue audio input.
Item When connecting devices (including a PC) with DVI/HDMI cable to the HDMI 2 terminal and inputting analogue audio signals from the AUDIO (R/L) jack. When connecting a PC to the EXT 4 terminal, and inputting analogue audio signals from the AUDIO (R/L) jack.

Bass enhancer

This function allows you to enjoy bass-enhanced sound.

HDMI 2

Automatic volume adjustment

EXT 4 (RGB)

Auto volume
Different sound sources sometimes do not have the same volume level, such as a programme and its commercial breaks. This function reduces this problem by equalizing levels.
You must set this to EXT 4 (RGB) when connecting devices (including a PC) with an HDMI-certified cable to the HDMI 2 terminal. If HDMI 2 is set, there will be no sound output.

Auto installation

The TV automatically detects and stores all available services in your area. This function also allows you to perform the channel setting for digital and analogue individually and reconfigure the settings after the initial auto installation has been completed.
Press a/b to select the broadcast standard you want to reconfigure, and then press ;.
PIN input is required when executing Programme setup. The default PIN is 1234. To change the PIN setting, refer to Password/Parental lock settings (Page 30). To clear the PIN setting (PIN input will no longer be needed), refer to CLEARING THE PIN (Page 41).
Press c/d to select Yes, and then press ;. Press a/b/c/d to select the desired language, and then press ;.

Digital setting

PIN input is required when executing Auto installation. The default PIN is 1234. To change the PIN setting, refer to Password/Parental lock settings (Page 30). To clear the PIN setting (PIN input will no longer be needed), refer to CLEARING THE PIN (Page 41). You cannot set the Home/Store setting and the country setting in Auto installation in the Setup menu. If you want to reconfigure those settings, automatically execute initial auto installation after executing Reset from the Setup menu. The current country setting is displayed on the screen.

E Additional search

Use this menu to add new services automatically after Digital search in the Auto installation menu has been completed.

E Manual search

Add new services within a specified frequency band.
Enter the frequency using 0_9 numeric buttons. You can perform Manual search with a service number only when the five Nordic countries have been selected in the country setting.
Press a/b to select the broadcast standard you want to search, and then press ;. After selecting the service you want to search, either Terrestrial or Cable, refer to Digital broadcast setting on pages 9_10.
The Digital search has a Reset function. This function allows you to reset all setting values.

E Digital search

E Analogue search
The TV searches for, sorts and stores all the receivable TV stations. Refer to Analogue broadcast setting on page 10.

LC-LE705E_GB.indd 27

2009/10/09 14:13:11

E Manual adjust

Configure various settings for each service using the colour (R/G/B) buttons.
Service no. Service name Lock CH skip Old LCN

Cable setting

Use this menu to add new services automatically after Digital search in the Auto installation menu has been completed. Follow steps 1 to 4 in Searching for cable broadcasts on page 10.

Lock CH skip Sort

Press a/b to select the desired service. Press the colour button on the remote control unit corresponding with the item you want to reconfigure.

PIN input is required when executing Child lock. The default PIN is 1234. To clear the PIN setting (PIN input will no longer be needed), refer to CLEARING THE PIN (Page 41).

Change PIN

Register a four-digit password number to use the Child lock function.
Enter the four-digit number as a PIN using 0_9 numeric buttons. Enter the same four-digit number as in step 1 to confirm.
The system PIN has been changed successfully displays.
You cannot set both RC control lock and Button control lock at the same time.

E Cancelling the lock

Press @ on the TV and set to Off to cancel the RC control lock. Press @ on the remote control unit and set to Off to cancel the Button control lock.
Refer to page 22 for menu operation using @ on the TV.
To view a locked channel, you must enter the PIN (see pages 28 and 29 for locking channels from viewing in DTV and ATV mode). When you select a locked channel, a PIN prompt message pops up. Press 6 to display the PIN input window.

Quick start

You can reduce the TVs start-up time after turning on the power with the remote control unit.
Item On The TV quickly starts up from standby. 30 W or more of power consumption is required during standby. Power consumption is small during standby.

Cancel PIN

Allows you to reset your PIN.
As a precautionary measure, make a note of your PIN on the back of this operation manual, cut it out and keep it in a safe place that children cannot reach.

Parental rating

This function allows DTV services to be restricted. It prevents children from watching violent or sexual scenes that may be harmful.

Blue illumination

The LED on the front of the TV is blue when illuminated.
Universal viewing and Parental approval pref. are ratings used exclusively in France. Refer to page 47 for details about ratings.
The factory default for this item is On. Set to Off if you do not want the LED to illuminate.

LC-LE705E_GB.indd 30

2009/10/09 14:13:13

Useful viewing functions

Selecting the picture size Selecting the WSS picture size automatically
Selecting the picture size manually
You can select the picture size. Selectable picture size varies with the type of signal received.
Item (for SD [Standard-Definition] signals) Keeps the original aspect ratio in a full screen display. For 14:9 letterbox pictures. A thin side bar appears on each side, and you may also see bars on the top and bottom with some programmes. In this mode, the picture is stretched toward each side of the screen. The picture may appear similar to Full depending on broadcast signals. For 16:9 squeeze pictures. For 16:9 letterbox pictures. Bars may appear on the top and bottom with some programmes. For 14:9 letterbox pictures. Bars may appear on the top and bottom with some programmes.

Music mode

Press c/d to select between Photo mode and Music mode, and then press ;. Press a/b/c/d to select the drive where you want to find your files, and then press ;.
You do not need to select the drive in step 2 when there is only one drive in the connected USB device. 16 is the maximum number of drives that can be displayed.
Rotating photos only applies to the temporarily selected item and this setting is not saved.

LC-LE705E_GB.indd 35

2009/10/09 14:13:19

Slide show

File name Time Time

E Selecting the BGM

File name

Playing:

Playing: Slide show BGM:

Buttons for music mode

Buttons Description When selecting the folder icon with the 6 mark: Go back to the parent directory. When selecting a folder icon: Enter this directory. When selecting a music file: Play music. Select a desired item. Page up. Page down. Return to the top menu. Stop music. Play/Pause music. Turn off the screen image for audio only output.
Buttons for slide show BGM select operation
Buttons Description When selecting the folder icon with the 6 mark: Go back to the parent directory. When selecting a folder icon: Enter this directory. When selecting a music file: Play music. Select a desired item. Page up. Page down. Return to the thumbnail selection screen. Stop music. Play/Pause music. Set the selected music to the slide show BGM. Reset the slide show BGM. ;
a/b (Cursor) c (Cursor) d (Cursor) 6 R button G button B button
a/b (Cursor) c (Cursor) d (Cursor) 6 R button G button Y button B button
When there are invalid music files, the g mark will be displayed for the file. The displayed play time may differ slightly from the actual play time depending on the files.
Only one song can be set to the slide show BGM. Slide show BGM will be reset in the cases below. Go back to the top menu. Change the INPUT SOURCE. When there are invalid music files, the g mark will be displayed for the file. The displayed play time may differ slightly from the actual play time depending on the files.

USB device compatibility

USB device File system Photo file format USB Memory, USB card reader (Mass Storage class) FAT/FAT32 JPEG (.jpg) (DCF2.0 compliant) MP3 (.mp3) Bitrate: 32 k, 40 k, 48 k, 56 k, 64 k, 80 k, 96 k, 112 k, 128 k, 160 k, 192 k, 224 k, 256 k, 320 kbps Sampling frequency: 32 k, 44.1 k, 48 kHz

E Slide show

Buttons for slide show operation
Buttons 6 B button Description Return to the thumbnail selection screen. Reveal/hide the guide display. Music file format
Progressive format jpeg files are not supported. Music files in USB 1.1 devices may not be played properly. Operation using USB hubs is not guaranteed.

This operation system should be used by a person who is accustomed to using PCs.

Return code (0DH): ?

Parameter
Input the parameter values, aligning left, and fill with blank(s) for the remainder (be sure that four values are input for the parameter). When the input parameter is not within an adjustable range, ERR returns (refer to Response code format).
RS-232C serial control cable (cross type)

Communication conditions

Set the RS-232C communications settings on the PC to match the TVs communications conditions. The TVs communications settings are as follows:
Baud rate Data length Parity bit Stop bit Flow control 9,600 bps 8 bits None 1 bit None
When ? is input for some commands, the present setting value responds.

Communication procedure

Send the control commands from the PC via the RS232C connector. The TV operates according to the received command and sends a response message to the PC. Do not send multiple commands at the same time. Wait until the PC receives the OK response before sending the next command. Make sure to send A with the carriage return and confirm that ERR returns before operating.

Response code format

Normal response
Return code (0DH) Problem response (communication error or incorrect command)

Return code (0DH)

LC-LE705E_GB.indd 39

RS-232C command list

CONTROL ITEM POWER SETTING INPUT SELECTION A COMMAND P I I I I CHANNEL D C C D O W R T T D A C H H T G V T V C U D D V D H P PARAMETER 0 _ _ _ * * _ _ * _ _ _ _ _ * _ _ * _ _ _ _ _ _ _ _ * _ _ _ _ _ _ _ _ _ CONTROL CONTENTS POWER OFF (STANDBY) INPUT SWITCHING (TOGGLE) TV (CHANNEL FIXED) DTV (CHANNEL FIXED) EXT 1_4, 9 (1_4, 9), HDMI 1_4 (5_8) TV DIRECT CHANNEL (1_99) CHANNEL UP CHANNEL DOWN THREE DIGIT DIRECT CHANNEL (1_999) (NonNordic countries) FOUR DIGIT DIRECT CHANNEL (1_9999) (Nordic countries only) DTV CHANNEL UP DTV CHANNEL DOWN EXT 1 (Y/C) EXT 1 (CVBS) EXT 1 (RGB) EXT 2 (Y/C) EXT 2 (CVBS) TOGGLE STANDARD MOVIE GAME USER DYNAMIC (Fixed) DYNAMIC PC AUTO 1_7, 100 VOLUME (0_60) TEXT T T D E E C X X P T T G * _ _ * _ _ * _ _ _ O O F F T T M M _ _ _ _ _ _ AUDIO CHANGE SLEEP TIMER SURROUND MUTE WIDE MODE CONTROL ITEM POSITION COMMAND H V C P W W W W W W W W W W W W M M M A A A A O O O O P P L H I I I I I I I I I I I I U U U C C C C F F F F O O C S D D D D D D D D D D D D T T T S S S H T T T T S S K E E E E E E E E E E E E E E E E U U U A M M M M PARAMETER * * * * _ * * * * _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ * * * _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ CONTROL CONTENTS H-POSITION (AV/PC) V-POSITION (AV/PC) CLOCK (0_180) PHASE (0_40) TOGGLE (AV) NORMAL (AV) ZOOM 14:9 (AV) PANORAMA (AV) FULL (AV) CINEMA 16:9 (AV) CINEMA 14:9 (AV) NORMAL (PC) CINEMA (PC) FULL (PC) DOT by DOT (AV/PC) UNDERSCAN (AV) TOGGLE MUTE MUTE OFF SURROUND TOGGLE SURROUND ON SURROUND OFF TOGGLE OFF SLEEP TIMER 30 MIN SLEEP TIMER 1 HOUR SLEEP TIMER 1 HOUR 30 MIN SLEEP TIMER 2 HOUR SLEEP TIMER 2 HOUR 30 MIN TEXT OFF TEXT ON (TOGGLE) DIRECT PAGE JUMP (100_899)

CLEARING THE PIN

Go to MENU > Setup. Press a/b to select Auto installation, Programme setup, Child lock or Reset, and then press ;. The PIN input window will display.
Press and hold both :r and i+ on the TV simultaneously until the message appears on the screen.

LC-LE705E_GB.indd 41

2009/10/09 14:13:24
Updating your TV via DVB-T
Ensure that your TV software version is always up to date. From time to time SHARP will make updated TV base software and DVB software available.

Information

Message list
When new software is detected, you can confirm the update information and download the software from Message list.

Download setup

Searching for updates*
* All countries except UK, Sweden and Italy are set to No for this function.
When the TV succeeds at downloading new software, the message is updated in the Message list of the Information menu. The software update will not be carried out if there is no new software available at the specified download time.
The TV automatically determines whether a new software version is available when the TV is in standby mode.
Item Yes No Now Automatically searches for new software updates available when the TV is in standby mode. Does not search for update information. Checks if there is new software immediately.

Receiver report

Display reports regarding failures and changes for timer settings.
If complex adjustments are made so that the settings cannot be restored to normal, you can reset the settings to the factory preset values.
Downloading the software Setup
You can select the method of update.
If the software is updated, the confirmation message New download information has been detected. appears.
If the TV receives the update service while in standby mode, a confirmation message displays after turning on the power.
Go to MENU > Setup > Reset. Press c/d to select Yes, and then press ;.
Now, TV will restart automatically, OK? displays on the screen.
Follow the screen prompts.
Item Starts downloading immediately. It takes approximately one hour to update. You cannot carry out other operations while downloading.

Cancels the download by pressing ; on the remote control unit when Discontinue is displayed on the screen during the update.
Press c/d to select Yes, and then press ;.
Now initialising. displays on the screen and blinks. After the reset has completed, the power shuts off and then comes back on. The screen will have returned to its original settings.
PIN input is required when executing Reset. The default PIN is 1234. To change the PIN setting, refer to Password/ Parental lock settings (Page 30). To clear the PIN setting (PIN input will no longer be needed), refer to CLEARING THE PIN (Page 41).
Starts downloading automatically several minutes after entering standby mode.
The TV must remain in standby mode for download. Do not turn off the power using a on the TV. Updating the software may take some time.

Identification

You can check the TV ID on the screen for reporting to customer service.

LC-LE705E_GB.indd 42

Updating your TV via USB
The TV displays a confirmation screen while checking the data in the inserted USB device.
If the data is not compatible with the system, an error message appears on the screen. Repeat steps 2 and 3 after pressing ;. When an error message displays, check to see if: The USB device is inserted firmly. The USB memory has two or more software update files. No data for updating the system exists in the USB memory. The software update file is broken. The software update file is not compatible with your TVs software. The current system is same as the system update data.

Software update

This function allows you to update to the latest software using a USB device. You must update the software through the USB terminal.
To check the software version for the TV, use the URL shown on the back cover.
This function is available only for the 705 model series.
Go to MENU > Setup > Software update. Press ; and then insert the USB device containing the software update file.
The TV displays the software version information after checking the data. Press c/d to select Yes to update the system, and then press ;. Press ; to automatically reset and start the update operation.
This operation may take a while.
The TV starts updating the system
Be sure to insert the USB device correctly into the terminal.
A confirmation message appears on the screen after completing the update and then automatically restarts the TV. Press ; to complete the operation.

Information on the software license for this product
Software composition The software included in this product is comprised of various software components whose individual copyrights are held by SHARP or by third parties. Software developed by SHARP and open source software The copyrights for the software components and various relevant documents included with this product that were developed or written by SHARP are owned by SHARP and are protected by the Copyright Act, international treaties, and other relevant laws. This product also makes use of freely distributed software and software components whose copyrights are held by third parties. These include software components covered by a GNU General Public License (hereafter GPL), a GNU Lesser General Public License (hereafter LGPL) or other license agreement. Obtaining source code Some of the open source software licensors require the distributor to provide the source code with the executable software components. GPL and LGPL include similar requirements. For information on obtaining the source code for the open source software and for obtaining the GPL, LGPL, and other license agreement information, visit the following website: http://www.sharp-eu.com/gpl/ We are unable to answer any questions about the source code for the open source software. The source code for the software components whose copyrights are held by SHARP is not distributed. Acknowledgements The following open source software components are included in this product: linux kernel busy box uClibc zlib libpng libjpeg mtd-utils

LC-LE705E_GB.indd 43

2009/10/09 14:13:25

Specifications

Item LCD COLOUR TV (32 o), LC32LE700E, LC-32LE700S, LC-32LX700E, LC-32LU700E, LC-32LU700S, LC-32LE705E, LC-32LE705S, LC-32LX705E, LC32LU705E, LC-32LU705S Advanced Super View & BLACK TFT LCD (32 o) 2,073,600 pixels (1,920 x 1,080) PAL/SECAM/NTSC 3.58/NTSC 4.43/PAL 60 Analogue Digital Receiving channel TV-tuning system STEREO/BILINGUAL Audio amplifier Speaker Terminals Antenna RS-232C EXT 1 EXT 2 EXT 3 EXT 4 HDMI 1 (EXT 5) HDMI 2 (EXT 6) HDMI 3 (EXT 7) HDMI 4 (EXT 8) EXT 9 USB HDMI 2/PC AUDIO (R/L) DIGITAL AUDIO OUTPUT C. I. (Common Interface)

OUTPUT

LCD COLOUR TV (40 o), LC40LE700E, LC-40LE700S, LC-40LX700E, LC-40LU700E, LC-40LU700S, LC-40LE705E, LC-40LE705S, LC-40LX705E, LC40LU705E, LC-40LU705S Advanced Super View & BLACK TFT LCD (40 o)
LCD panel Resolution Video colour system TV function TV-standard
CCIR (B/G, I, D/K, L/L) DVB-T (2K/8K OFDM), DVB-C IR A ch_E69 ch (Digital), E2_E69 ch, F2_F10 ch, I21_I69 ch, IR A_IR J ch Hyper-band, S1_S41 ch Auto Preset 999 ch (non-Nordic [DTV]), Auto Preset 9999 ch (Nordic [DTV]), Auto Preset 99 ch (ATV), Auto Label, Auto Sort NICAM/AW x 2 (35 mm x 100 mm) x 2 UHF/VHF 75 q Din type (analogue & digital) D-Sub 9 pin male connector SCART (AV input, Y/C input, RGB input, TV output) SCART (AV input/monitor output, Y/C input) COMPONENT IN (Y/PB(CB)/PR(CR), RCA pin (AUDIO R/L)) 15 pin mini D-sub HDMI HDMI HDMI HDMI RCA pin (AV input) USB 3.5 mm jack*1 Optical S/PDIF digital audio output EN50221, R206001, CI Plus specification RCA pin (AUDIO R/L) 3.5 mm jack (audio output) Czech, Danish, Dutch, English, Estonian, Finnish, French, German, Greek, Hungarian, Italian, Latvian, Lithuanian, Norwegian, Polish, Portuguese, Russian, Slovak, Slovene, Spanish, Swedish, Turkish, Ukrainian AC 220_240 V, 50 Hz 93 W (0.2 W standby*2) 10.5 kg (without stand), 13.5 kg (with stand) 0 C to e 40 C 133 W (0.2 W standby*2) 12.3 kg (without stand), 16.2 kg (with stand)

VHF/UHF CATV

Headphones OSD language
Power requirement Power consumption (method IEC62087) Weight Operating temperature
The HDMI 2 and EXT 4 terminals can both use the same audio input terminal. Standby power consumption applies when the TV is set to not receive EPG data.

LC-LE705E_GB.indd 44

2009/10/09 14:13:26
Item LCD COLOUR TV (46 o), LC46LE700E, LC-46LE700S, LC-46LX700E, LC-46LU700E, LC-46LU700S, LC-46LE705E, LC-46LE705S, LC-46LX705E, LC46LU705E, LC-46LU705S Advanced Super View & BLACK TFT LCD (46 o) 2,073,600 pixels (1,920 x 1,080) PAL/SECAM/NTSC 3.58/NTSC 4.43/PAL 60 Analogue Digital Receiving channel TV-tuning system STEREO/BILINGUAL Audio amplifier Speaker Terminals Antenna RS-232C EXT 1 EXT 2 EXT 3 EXT 4 HDMI 1 (EXT 5) HDMI 2 (EXT 6) HDMI 3 (EXT 7) HDMI 4 (EXT 8) EXT 9 USB HDMI 2/PC AUDIO (R/L) DIGITAL AUDIO OUTPUT C. I. (Common Interface)
LCD COLOUR TV (52 o), LC52LE700E, LC-52LE700S, LC52LE705E, LC-52LE705S
Advanced Super View & BLACK TFT LCD (52 o)
CCIR (B/G, I, D/K, L/L) DVB-T (2K/8K OFDM), DVB-C IR A ch_E69 ch (Digital), E2_E69 ch, F2_F10 ch, I21_I69 ch, IR A_IR J ch Hyper-band, S1_S41 ch Auto Preset 999 ch (non-Nordic [DTV]), Auto Preset 9999 ch (Nordic [DTV]), Auto Preset 99 ch (ATV), Auto Label, Auto Sort NICAM/AW x 2 (35 mm x 100 mm) x 2 UHF/VHF 75 q Din type (analogue & digital) D-Sub 9 pin male connector SCART (AV input, Y/C input, RGB input, TV output) SCART (AV input/monitor output, Y/C input) COMPONENT IN (Y/PB(CB)/PR(CR), RCA pin (AUDIO R/L)) 15 pin mini D-sub HDMI HDMI HDMI HDMI RCA pin (AV input) USB 3.5 mm jack*1 Optical S/PDIF digital audio output EN50221, R206001, CI Plus specification RCA pin (AUDIO R/L) 3.5 mm jack (audio output) Czech, Danish, Dutch, English, Estonian, Finnish, French, German, Greek, Hungarian, Italian, Latvian, Lithuanian, Norwegian, Polish, Portuguese, Russian, Slovak, Slovene, Spanish, Swedish, Turkish, Ukrainian AC 220_240 V, 50 Hz 162 W (0.2 W standby*2) 18.5 kg (without stand), 23.5 kg (with stand) 0 C to e 40 C 189 W (0.2 W standby*2) 22.5 kg (without stand), 27.6 kg (with stand)
The HDMI 2 and EXT 4 terminals can both use the same audio input terminal. J Standby power consumption applies when the TV is set to not receive EPG data. As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units.