Press a/b/c/d to select the desired language, and then press OK. Setting the country (Location of TV set screen).
Austria Finland Greece A B/G
E Checking signal strength
Press a/b to select Signal Strength.

FIN B/G GR B/G

Supply Voltage Signal Strength Channel Strength CH No. Signal Strength Current Quality 0 Max 0 21
Press a/b/c/d to select your country or area, and then press OK.
The Location of TV set screen only appears during the first installation.

Current

E Checking channel strength
Press a/b to select Channel Strength, and then press OK.
You can input a specified frequency band using 0 - 9 numeric buttons.
Supply Voltage Signal Strength

Starting channel search.

CH No.
Analogue Search Channel Strength Signal Strength Current Quality 0 Max 0
Press c/d to select Digital Search or Analogue Search, and then press OK.
If you want to search for more broadcasts, execute Additional Search from the Programme Setup menu. (Pages 26 and 27) To watch both analogue broadcasts and digital broadcasts, you should perform the channel search setting for each broadcast.
Position and align the antenna so that the maximum possible values for Signal Strength and Quality are obtained.
The values of Signal Strength and Quality indicate when to check the appropriate alignment of the antenna.

EXAMPLE:

If you execute Digital Search in the initial auto installation wizard, you should perform Analogue Search from Auto Installation under the Setup menu.

LC-46X8E_GB.indd 9

2008/02/14 15:45:59

Watching TV

Daily operation Switching on/off

Turning on/off the power

Press a on the TV. Switch it off by pressing a on the TV. NOTE
When turning off the power with a on the TV, EPG data (electronic programme guide) will be lost, and programmed timer recordings will not be performed by the TV.
Selecting external video source
Once the connection is made, press b to display the INPUT SOURCE screen, and then press a/b to switch over to the appropriate external source with OK.
INPUT SOURCE TV EXT1 EXT2 EXT3 EXT4 EXT5

Selecting Sound mode

E DTV mode:
If multi sound modes are received, each time you press 2 the mode switches as follows.

Audio (ENG) : STEREO

Standby mode E To standby mode
If the TV set is switched on, you can switch it to standby by pressing B on the remote control.
Audio (ENG) : CH A CH A CH B CH AB
E Switching on from standby
From standby, press B on the remote control.

Audio (ENG) : MONO

Press c/d to select L or R sound when the STEREO or DUAL MONO screen is displayed.

TV indicator status

B indicator Off Green Red Power off Power on Standby Status
Audio (ENG) : STEREO L/R L R LR
The sound mode screen disappears in 6 seconds. Selectable items vary depending on the received broadcasts.

E ATV mode:

Each time you press 2, the mode switches as illustrated in the following tables.
NICAM TV broadcasts selection Selectable items NICAM STEREO, MONO NICAM CH A, NICAM CH B, NICAM CH AB, MONO NICAM MONO, MONO A2 TV broadcasts selection Signal Selectable items Stereo STEREO, MONO Bilingual CH A, CH B, CH AB Monaural MONO Signal Stereo Bilingual Monaural
If you are not going to use this TV for a long period of time, be sure to remove the AC cord from the power outlet. A small amount of electric power is still consumed even when a is turned off.
Switching between analogue and digital broadcasts
E Watching digital broadcasts E Watching analogue broadcasts

Changing channels

With Pr/Ps: With 0 - 9:
When no signal is input, the sound mode will display MONO.

LC-46X8E_GB.indd 10

2008/02/14 15:46:00
EPG (Electronic Programme Guide)
EPG (Electronic Programme Guide) is a programme list that is displayed on the screen. With the EPG, you can check the schedule of DTV/RADIO/DATA, view detailed information about them, tune to an event currently on-air and set a timer for future events.

EPG Overview

E Basic functions
E Select a programme using EPG (Page 12) E Check programme information (Page 12)

E Useful functions

E Search for a programme by category (Page 12) E Search for a programme by date and time (Page 12) E Timer recoding using EPG (Page 13)
Useful settings for using EPG
Common Operation EPG display settings E EPG Setup (setting for receiving EPG data)
If you want to use the EPG for digital stations, select Yes. The EPG data must be automatically captured while the TV set is in standby mode. After setting to Yes, it may take some time to turn off the power using the remote control due to the process of the data capture. NOTE

AUDIO R L EXT8 COMPONENT

3.5 mm stereo minijack cable

R L Y PB (CB) PR (CR)

COMPONENT

S-VIDEO/VIDEO connection

DVI/HDMI conversion
Using an DVI/HDMI adapter cable, the digital video signals of a DVD can also be played via the compatible HDMI connection. The sound must be fed in additionally.
When connecting an HDMI-DVI conversion adapter/cable to the HDMI terminal, the image may not come in clearly.
E VCR E DVD E Blu-ray player/recorder E Game console E Camcorder You can use the EXT3 terminal when connecting to a game console, camcorder, a DVD recorder and some other equipment.
Both HDMI and DVI use the same HDCP copy protection method.

E After connecting

HDMI Audio Select After connecting, you must set the audio signal compatible with the cable you use for the HDMI device. 1 Go to MENU > Option > HDMI Audio Select. 2 Select Digital for audio signals via the HDMI terminal. Select Analogue for audio signals via the AUDIO jack (EXT6). NOTE
If a connected HDMI device is AQUOS LINK compatible, you can take advantage of versatile functions. (Pages 20 - 22) Video noise may occur depending on the type of HDMI cable used. Make sure to use a certified HDMI cable. When playing the HDMI image, the best possible format for the picture will be detected and set automatically.

S-video cable AV cable

When using an S-video cable, you also need to connect an audio cable (R/L). EXT3: The S-VIDEO terminal has priority over the VIDEO terminal.

Supported video signal:

576i, 576p, 480i, 480p, 1080i, 720p, 1080p See page 36 for PC signal compatibility. 16

LC-46X8E_GB.indd 16

2008/02/14 15:46:16

SCART connection

E Decoder

E VCR E DVD recorder

E When using the EXT2 (SCART) terminal
If your VCR supports TV-VCR advanced AV Link systems, you can connect the VCR using a fully wired SCART cable.

Decoder

In cases when the decoder needs to receive a signal from the TV, make sure to select the appropriate input terminal to which the decoder is connected in Manual Adjust in the Analogue Setting menu. (Page 27) TV-VCR advanced AV Link systems may not be compatible with some external sources. You cannot connect the VCR with Decoder using a fully wired SCART cable when selecting Y/C under the EXT2 in the Input Select menu.
Controlling devices with SCART using AV Link
This TV incorporates four typical AV Link functions for smooth connections between the TV and other audiovisual equipment.

In addition to displaying the TVs own Timer list (Page 12), you can also call up the external players Top menu or AQUOS BD Players/AQUOS Recorders Title list provided that the devices support AQUOS LINK.
Multiple control of HDMI devices
You can select which HDMI device to operate using the OPTION button. NOTE
When you use AQUOS LINK, make sure to use a certified HDMI cable. Point the remote control toward the TV, not to the connected HDMI device. Video noise may occur depending on the type of HDMI cable used. Make sure to use a certified HDMI cable. Up to 3 HDMI recording devices, one AV amplifier and two players can be connected using this system. These operations affect the HDMI device selected as the current external source. If the device does not operate, turn on the device and select the appropriate external source using b. When you insert/remove HDMI cables or change connections, turn on all connected HDMI devices before turning on the TV. Confirm that picture and audio are correctly output by selecting EXT4, EXT5 or EXT6 from the INPUT SOURCE menu.

LC-46X8E_GB.indd 20

2008/02/14 15:46:24

AQUOS LINK connection

First connect the AQUOS AUDIO speaker system or an AQUOS BD Player/AQUOS Recorder that supports the HDMI CEC protocol. NOTE
Refer to the operation manual of the device to be connected for further details. After unplugging connection cables or changing the connection pattern, first turn on the power of the TV with all relevant devices power turned on. Change the external input source by pressing b, select the appropriate external source and verify the audiovisual output. The cables illustrated in the following explanation are commercially available items.
Connecting an AQUOS BD Player/AQUOS Recorder via the AQUOS AUDIO speaker system
Connecting an AQUOS BD Player/AQUOS Recorder only

Optical AUDIO cable

HDMIcertified cable
AQUOS BD Player/ AQUOS Recorder
AQUOS AUDIO speaker system

AQUOS LINK Setup

AQUOS LINK Auto power on
If this is activated, the One Touch Play function is enabled. While the TV is in standby mode, it automatically turns on and plays back the image from the HDMI source. 1 Press MENU and the MENU screen displays. 2 Press c/d to select Option. 3 Press a/b to select AQUOS LINK Setup, and then press OK. 4 Press a/b to select Auto Power On, and then press OK. 5 Press c/d to select On, and then press OK. NOTE
The factory default for this item is Off.
Repeat steps 1 to 3 in AQUOS LINK Auto power on. Press a/b to select Selecting Recorder, and then press OK. Select the recorder, and then press OK.
If you have connected the AQUOS AUDIO speaker system between the TV and an AQUOS Recorder, the external sources indication changes from EXT5 to EXT5 (Sub).

Using Genre Info.

This function allows you to automatically switch to the appropriate sound mode depending on the genre information included the digital broadcast. 1 Repeat steps 1 to 3 in AQUOS LINK Auto power on. 2 Press a/b to select Using Genre Info., and then press OK. 3 Press c/d to select On, and then press OK. 21

Selecting recorder

Here, you can select a recorder for the recording from several connected recorders.

LC-46X8E_GB.indd 21

2008/02/14 15:46:25
Operating an AQUOS LINK device
AQUOS LINK allows you to operate the HDMIconnected device with one remote control. 1 Open the remote controls flip cover. 2 Press PLAY I to start playback of a title.
See the right column, section Playback of titles using AQUOS LINK if you want to start playback using the list of the titles of the AQUOS BD Player/ AQUOS Recorder.
Playback of titles using AQUOS LINK
This section explains how to play back a title in the AQUOS BD Player/AQUOS Recorder. 1 Open the remote controls flip cover. 2 Press OPTION.
The AQUOS LINK Menu displays.
Press a/b to select Top Menu/Title List, and then press OK.
The linked recorder now powers on and the TV automatically selects the appropriate external input source. The title list data from the connected AQUOS BD Player/AQUOS Recorder displays.
Press FWD J to fast forward. Press REV G to reverse. Press STOP H to stop. Press B to turn the HDMI-connected device on/off.
Select the title with a/b/c/d, and then press PLAY I.
Listening with the AQUOS AUDIO speaker system
You can opt to listen to the TV sound only from the AQUOS AUDIO speaker system. 1 Open the remote controls flip cover. 2 Press OPTION.
AQUOS LINK Menu Recorder EPG Top Menu/Title List Media change By AQUOS AUDIO SP By AQUOS SP Sound mode change Model select
Selecting media type for CEC-compatible recorder
If your recorder has multiple storage media, select the media type here. 1 Open the remote controls flip cover. 2 Press OPTION.
Press a/b to select Media change, and then press OK. Select the desired medium, such as DVD or HDD. The media type changes every time you press OK.

HDMI device selection

If multiple HDMI devices are connected in a daisy chain, you can specify which device to control here. 1 Open the remote controls flip cover. 2 Press OPTION.
Press a/b to select By AQUOS AUDIO SP, and then press OK.
The sound from the TV speaker and headphone terminal is silenced and only the sound from the AQUOS AUDIO speaker system is audible.
Listening with the AQUOS TV speaker system
You can opt to listen to the TV sound only from the AQUOS TV speaker system. 1 Open the remote controls flip cover. 2 Press OPTION.
Press a/b to select Model select, and then press OK. The HDMI device changes every time you press OK.

AV MODE

AV MODE gives you several viewing options to choose from to best match the system environment, which can vary due to factors like room-brightness, type of programme watched or the type of image input from external equipment. 1 Press AV MODE. 2 Each time you press AV MODE, the mode changes.
You can also switch the mode on the Picture and Audio menu screen by pressing AV MODE.

Surround

This function allows you to enjoy realistic live sound.

Power Save Settings

STANDARD: For a highly defined image in a normally bright room. MOVIE: For viewing a movie in a darkened room. GAME: For playing of video games. PC*: For PC. USER: Allows the user to customise settings as desired. You can set the mode for each input source. DYNAMIC (Fixed): For a clear-cut image emphasising high contrast for sports viewing. (The Picture and Audio settings cannot be adjusted.) DYNAMIC: For a clear-cut image emphasising high contrast for sports viewing.

Power Control

No Signal Off
When set to Enable the TV will automatically enter the standby mode if there is no signal input for 15 minutes.
Five minutes before the TV enters standby mode, the remaining time displays every minute.

NOTE NOTE

The item marked with * is available only when selecting EXT4, EXT5, EXT6 or EXT7 from the INPUT SOURCE menu. When a TV programme finishes, this function may not operate.

LC-46X8E_GB.indd 25

2008/02/14 15:46:34

Digital channel settings

No Operation Off
The TV will automatically enter the standby mode if no operations are performed during the time span you set (30min. or 3hr.).

Programme Setup

Digital Setting
You can reconfigure DTV services settings automatically or manually.

Ecology

When set to Yes the TV activates the following power saving mode.
OPC set to On. (Page 24) Standby Mode set to Mode2. (Page 32) No Signal Off set to Enable. (Page 25) No Operation Off set to 3hr. (Page 26)

E Additional Search

Use this menu to add new services automatically after auto installation has been completed.

E Manual Search

Add new services within a specified frequency band.
Enter the frequency using 0 - 9 numeric buttons. You can perform Manual Search with a channel number only when using the LC-46X8S model.

E Manual Adjust

Configure various settings for each service using the Colour (R, G, Y, B) buttons.

The name can be 5 characters or less. If a channel name is less than 5 characters, select END to set the channel name.
Press c/d to select Yes, and then press OK to erase the selected programme. All the subsequent programmes move up. Repeat steps 3 and 4 until all desired channels are erased.

LC-46X8E_GB.indd 27

2008/02/14 15:46:38
Password/Parental lock settings
Language Settings (language, subtitle, multi audio)

Child Lock

Allows you to use a PIN to protect certain settings from being accidentally changed.

Language

You can select a OSD language from the Setup menu. Select from among 22 languages. (Czech, Danish, Dutch, English, Estonian, Finnish, French, German, Greek, Hungarian, Italian, Latvian, Lithuanian, Norwegian, Polish, Portuguese, Russian, Slovak, Slovene, Spanish, Swedish, Turkish)

Change PIN

Register a 4-digit password number to use the Child Lock function. 1 Enter the 4-digit number as a PIN using 0 9. 2 Enter the same 4-digit number as in step 1 to confirm.
The system PIN has been changed successfully displays.
Set up to 2 preferred subtitle languages (including subtitles for the hearing impaired) to display if subtitles are available. Selectable items E 1st Language E 2nd Language E For hearing impaired
To view a locked channel, you must enter the PIN. (See pages 26 and 27 for locking channels from viewing in analogue TV and DTV mode.) When you select a locked channel, a PIN prompt message pops up. Press 6 to display the PIN input window.

Cancel PIN

Allows you to reset your PIN. NOTE
As a precautionary measure, make a note of your PIN on the back of this operation manual, cut it out and keep it in a safe place that children cannot reach.
E Switching subtitle languages
Each time you press [ on the remote control, the subtitle switches. Off 1st Language

Parental rating

This function allows DTV services to be restricted. It prevents children from watching violent or sexual scenes that may be harmful. NOTE

INPUT SOURCE TV EXT1 EXT2 EXT3 DVD EXT5 EXT6
You cannot change labels if the input source is TV.

LC-46X8E_GB.indd 32

Connecting a PC

HDMI Connection

PC HDMI-certified cable EXT4 or 5
Displaying a PC image on the screen Selecting the picture size
You can select the picture size. 1 Press f.
The WIDE MODE menu displays.
PC DVI/HDMI conversion cable EXT6
Press f or a/b to select a desired item on the menu.
Connect the PC before making adjustments. Selectable picture size may vary with input signal type.

Analogue Connection

PC RGB cable EXT7

Normal

3.5 mm stereo minijack cable PC RGB/DVI conversion cable EXT7 Full: An image fully fills the screen. Cinema: For letter box pictures. Bars may appear on the top and bottom with some programmes. Normal: Keeps the original aspect ratio in a full screen display. Dot by Dot: Displays an image with the same number of pixels on the screen.
Refer to page 29 for AV signals (480i/480p/576i/576p/ 720p/1080i/1080p). The analogue D-sub terminal (EXT7) is not compatible with 480i/576i/1080p signals.
The PC input terminals are DDC1/2B-compatible. Refer to page 36 for a list of PC signals compatible with the TV. Macintosh adaptor may be required for use for some Macintosh computers. When connecting to a PC, the correct input signal type is automatically detected except 1024 g 768 and 1360 g 768 signals.

LC-46X8E_GB.indd 33

2008/02/14 15:46:42
Adjusting the PC image automatically
This function enables the screen to be automatically adjusted to its best possible condition when the analogue terminals of the TV and PC are connected with a commercially available DVI/D-sub conversion cable, etc.
H-Pos.: Centres the image by moving it to the left or right. V-Pos.: Centres the image by moving it up or down. Clock: Adjusts when the image flickers with vertical stripes. Phase: Adjusts when characters have low contrast or when the image flickers.
For resetting all adjustment items to the factory preset values, press a/b to select Reset, and then press OK. Clock and Phase in the Fine Sync. menu can be adjusted only when inputting analogue signals.

Auto Sync.

Selecting input resolution
When Auto Sync. is successful, Auto Sync completed successfully displays. If not, Auto Sync. failed. Auto Sync. may fail even if Auto Sync completed successfully displays. Auto Sync. may fail if the computer image has low resolution, has unclear (black) edges, or is moved while executing Auto Sync. Be sure to connect the PC to the TV and switch it on before starting Auto Sync. Auto Sync. can be executed only when inputting analogue signals through the EXT7 terminal.

Some input signals may have to be registered manually to display properly. The pairs of input signals (resolutions) in the list below are not distinguishable when received. In such cases, you have to set the correct signal manually. After setting once, it will display when the same signal (resolution) is input again.

Input Signal

1024 x x 768
Adjusting the PC image manually
Ordinarily you can easily adjust the picture as necessary to change image position using Auto Sync. In some cases, however, manual adjustment is needed to optimise the image.

(Example)

You can only select the Input Signal on the Setup menu when receiving one of the 2 input signals listed above.

Fine Sync.

Press a/b to select the specific adjustment item. Press c/d to adjust the item to the desired position.
H-Pos. V-Pos. Clock Phase

[ 90] [ 39] [ 90] [ 20]

a a a a

b b b b

LC-46X8E_GB.indd 34

2008/02/14 15:46:45

RS-232C port specifications

PC Control of the TV

When a programme is set, the TV can be controlled from the PC using the RS-232C terminal. The input signal (PC/video) can be selected, the volume can be adjusted and various other adjustments and settings can be made, enabling automatic programmed playing. Use an RS-232C cable cross-type (commercially available) for the connections. NOTE
This operation system should be used by a person who is accustomed to using PCs.

Parameter

Input the parameter values, aligning left, and fill with blank(s) for the remainder. (Be sure that four values are input for the parameter.) When the input parameter is not within an adjustable range, ERR returns. (Refer to Response code format.)
When ? is input for some commands, the present setting value responds.
RS-232C serial control cable (cross type)

Communication conditions

Set the RS-232C communications settings on the PC to match the TVs communications conditions. The TVs communications settings are as follows:
Baud rate: Data length: Parity bit: Stop bit: Flow control: 9,600 bps 8 bits None 1 bit None

Response code format

Normal response

Return code (0DH)

Problem response (communication error or incorrect command)

Communication procedure

Send the control commands from the PC via the RS232C connector. The TV operates according to the received command and sends a response message to the PC. Do not send multiple commands at the same time. Wait until the PC receives the OK response before sending the next command. Make sure to send A with the carriage return and confirm that ERR returns before operating.

After sending the return code (0DH), make sure to send line feed (0AH) as well.

Command format

Eight ASCII codes eCR

C1 C2 C3 C4 P1 P2 P3

Command 4-digits
Parameter 4-digits Return code
Command 4-digits: Command. The text of four characters. Parameter 4-digits: Parameter 0 - 9, blank, ?

LC-46X8E_GB.indd 35

2008/02/14 15:46:47

PC compatibility chart

Resolution
VGA SVGA XGA WXGA SXGA SXGA+ 640 g g g g g g1050

Horizontal Frequency

31.5 kHz 37.9 kHz 48.4 kHz 47.7 kHz 64.0 kHz 65.3 kHz

Vertical Frequency

60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz

Analogue (DSub)

Digital (HDMI)

VESA Standard

VGA, SVGA, XGA, WXGA, SXGA and SXGA+ are registered trademarks of International Business Machines Corporation.
This TV has only limited PC compatibility, correct operation can only be guaranteed if the video card conforms exactly to the VESA 60 Hz standard. Any variations from this standard will result in picture distortions.

RS-232C command list

CONTROL ITEM POWER SETTING INPUT SELECTION A COMMAND P O W R I I I I CHANNEL T G D T D A V D T V PARAMETER 0 _ _ _ * * _ _ _ _ _ _ * _ _ * _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ ? * _ _ _ _ _ _ _ _ * _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ ? _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ ? _ CONTROL CONTENTS POWER OFF INPUT SWITCHING (TOGGLE) TV (CHANNEL FIXED) DTV (CHANNEL FIXED) EXT1 - 8 (1 - 8) TV DIRECT CHANNEL (1 - 99) CHANNEL UP CHANNEL DOWN DTV DIRECT CHANNEL (1 - 999) DTV CHANNEL UP DTV CHANNEL DOWN EXT1 (Y/C) EXT1 (CVBS) EXT1 (RGB) EXT2 (Y/C) EXT2 (CVBS) EXT2 (RGB) EXT3 EXT3 (S-VIDEO) EXT3 (VIDEO) TOGGLE STANDARD MOVIE GAME USER DYNAMIC (Fixed) DYNAMIC PC 1-7 VOLUME (0 - 60) TEXT AUDIO CHANGE SLEEP TIMER SURROUND MUTE WIDE MODE CONTROL ITEM POSITION COMMAND H P O S V C P O S L C K E PARAMETER * * * * _ * * * * _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ * * * * _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ * _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ CONTROL CONTENTS H-POSITION (AV/PC) V-POSITION (AV/PC) CLOCK (0 - 180) PHASE (0 - 40) TOGGLE (AV) NORMAL (AV) ZOOM 14:9 (AV) PANORAMA (AV) FULL (AV) CINEMA 16:9 (AV) CINEMA 14:9 (AV) NORMAL (PC) CINEMA (PC) FULL (PC) DOT by DOT (AV/PC) UNDERSCAN (AV) TOGGLE MUTE ON MUTE OFF SURROUND TOGGLE SURROUND ON SURROUND OFF TOGGLE OFF SLEEP TIMER 30 MIN SLEEP TIMER 1 HOUR SLEEP TIMER 1 HOUR 30 MIN SLEEP TIMER 2 HOUR SLEEP TIMER 2 HOUR 30 MIN TEXT OFF TEXT ON (TOGGLE) DIRECT PAGE JUMP (100 - 899)
P H S W W W W W W W W W W W W I I I I I I I I I I I I
D E D E D E D E D E D E D E D E D E D E D E D E T T T E E E

D C C H C H U P

C H D W _ D D D INPUT SELECTION B I I I I I I I I I AV MODE SELECTION A A A A A A A A A VOLUME T T T V D U P * _

D W _ ? *

N P N P N P N P N P N P N P N P N P

M U M U M U

A C S U A C S U A C S U A C H A O F O F O F O F O F O F T T E E
V M D V M D V M D V M D V M D V M D V M D V M D V M D
T M 0 T M 1 T M 2 T M 3 T M 4 T M 5 X X T T *

V O L M

D C P G

LC-46X8E_GB.indd 36

2008/02/14 15:46:49

Appendix

Troubleshooting
Problem No power. Possible Solution Check if you pressed B on the remote control unit. If the indicator on the TV lights up red, press B. Is the AC cord disconnected? Check if you pressed a on the TV. External influences such as lightning, static electricity, etc., may cause improper operation. In this case, operate the unit after first turning the power off, or unplugging the AC cord and replugging it in after 1 or 2 minutes. Are batteries inserted with polarity (e, f) aligned? Are batteries worn out? (Replace with new batteries.) Are you using it under strong or fluorescent lighting? Is a fluorescent light illuminating to the remote control sensor?

Unit cannot be operated.

Remote control unit does not operate.

Picture is cut off.

Is the image position correct? Are screen mode adjustments (WIDE MODE) such as picture size made correctly? (Pages 29 and 33) Adjust the picture tone. Is the room too bright? The picture may look dark in a room that is too bright. Check the Colour System setting. (Pages 27 and 32) The units internal temperature has increased. Remove any objects blocking the vent or clean. Is the Sleep Timer set? Select Off from the Sleep Timer menu. (Page 26) Is No Signal Off or Ecology activated? Are connections to external equipment correct? (Pages 15 - 17) Is the input signal type selected correctly after connection? (Page 32) Is the correct input source selected? (Page 10) Is a non-compatible signal being input? (Page 36) Is the picture adjustment correct? (Pages 24-25) Is the antenna connected properly? (Page 8) Is On selected in Audio Only? (Page 30)

Now initialising.

Identification
You can check the TV ID on the screen for reporting to customer service.

CLEARING THE PASSWORD

Message List
When software is detected in the Download Setup menu and No is selected, you can update the software from the Message List menu. Press c/d to select Yes after confirming the message, and then press OK. NOTE
When the TV succeeds at downloading new software, the message is updated in the Message List of the Information menu. The software update will not be carried out if there is no new software available at the specified download time.
Go to MENU > Setup. Press a/b to select Auto Installation, Programme Setup, Child Lock, Reset, and the PIN input screen displays.
Press and hold both CH r and VOL k on the TV simultaneously until the message appears on the screen.

LC-46X8E_GB.indd 38

Specifications
LCD panel Resolution Video Colour System TV Function TV-Standard Receiving Channel Analogue Digital VHF/UHF CATV
46o LCD COLOUR TV, Model: LC-46X8E, LC-46X8S
46o Advanced Super View & BLACK TFT LCD 2,073,600 pixels (1920 g 1080) PAL/SECAM/NTSC 3.58/NTSC 4.43/PAL 60 CCIR (B/G, I, D/K, L/L) DVB-T (2K/8K OFDM) E2E69ch, F2F10ch, I21I69ch, IR AIR Jch (Digital: E5-E69ch) Hyper-band, S1S41ch Auto Preset 999 ch (ATV: 99 ch), Auto Label, Auto Sort NICAM/Acd/m2 (in DYNAMIC mode) 60,000 hours (at Default Backlight position of STANDARD mode) H : 176 V : 176 15W g 2 (100 mm g 40 mm) g 4 Antenna RS-232C EXT1 EXT2 EXT3 EXT4 EXT5 EXT6 EXT7 EXT8 DIGITAL AUDIO OUTPUT C. I. (Common Interface) OUTPUT Headphones UHF/VHF 75 q Din type (Analogue & Digital) D-Sub 9 pin male connector SCART (AV input, Y/C input, RGB input, TV output) SCART (AV input/monitor output, Y/C input, AV Link, RGB input) S-VIDEO (Y/C input), RCA pin (AV input) HDMI HDMI HDMI, 3.5 mm jack 15 pin mini D-sub, 3.5 mm jack COMPONENT IN: Y/PB(CB)/PR(CR), RCA pin (L/R) Optical SPDIF Digital audio output EN50221, R206001 RCA pin (Audio) 3.5 mm jack (Audio output) Czech, Danish, Dutch, English, Estonian, Finnish, French, German, Greek, Hungarian, Italian, Latvian, Lithuanian, Norwegian, Polish, Portuguese, Russian, Slovak, Slovene, Spanish, Swedish, Turkish AC 220 - 240 V, 50 Hz 245 W (0.5 W Standby) (Method IEC60107) 22.5 kg (Without stand), 26.5 kg (With stand) 0C to k40C
TV-Tuning System STEREO/BILINGUAL Brightness Backlight life Viewing angles Audio amplifier Speaker Terminals

OSD language

Power Requirement Power Consumption Weight Operating temperature
As a part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units. NOTE

Refer to the inside back cover for dimensional drawings.

Optional accessory

The listed optional accessories are available for the LCD colour TVs. Please purchase them at your nearest shop.
Additional optional accessories may be available in the near future. When purchasing, please read the newest catalogue for compatibility and check the availability. No. 1 Part name Wall mount bracket Part number AN-52AG4
When using Wall-mount bracket AN-52AG4
Wall bracket B has an attachment pitch of 400 mm. Assemble wall brackets using mark C on wall bracket A and mark A on wall bracket B. Mark b on wall bracket B shows the center position for the LCD TV. Install the Wall-mount Brackets using screw holes 2. Refer to the Wall-mount bracket operation manual for details.

LC-46X8E_GB.indd 39

2008/02/14 15:46:51

End of life disposal

A. Information on Disposal for Users (private households) 1. In the European Union
Attention: If you want to dispose of this equipment, please do not use the ordinary dust bin! Used electrical and electronic equipment must be treated separately and in accordance with legislation that requires proper treatment, recovery and recycling of used electrical and electronic equipment. Following the implementation by member states, private households within the EU states may return their used electrical and electronic equipment to designated collection facilities free of charge*. In some countries* your local retailer may also take back your old product free of charge if you purchase a similar new one. *) Please contact your local authority for further details. If your used electrical or electronic equipment has batteries or accumulators, please dispose of these separately beforehand according to local requirements. By disposing of this product correctly you will help ensure that the waste undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health which could otherwise arise due to inappropriate waste handling.