(UX-470) (FO-880/NX-670)

UX-470DE FO-880DE/NX-670DE 3. Diagnostic items description 3. 1. Soft switch mode
Used to change the soft switch settings. The soft switch which is stored internally is set by using the keys. The available soft switches are SW-A1 to SW-M2. The content of soft switches is shown in page 2-5 to 2-16. The contents are set to factory default settings.

3. 6. Signal send mode

This mode is used to send various signals to the circuit during FAX communication. Every push of START key sends a signal in the following sequence. Moreover, the signal sound is also output to the speaker when the line monitor of the soft switch is on. [1] No signal (CML signal turned on) [2] 9600bps [3] 7200bps [4] 4800bps [5] 2400bps [6] 300bps (FLAG) [7] 2100Hz (CED) [8] 1100Hz (CNG) [9] END
3. 2. ROM & RAM check
ROM executes the sum check, and RAM executes the matching test. The result will be notified with the number of short sounds of the buzzer as well as by printing the ROM & RAM check list. Number of short sounds of buzzer 0 No error 1 ROM error 2 RAM error (32Kbyte)

3. 3. Aging mode

If any document is first present, copying will be executed sheet by sheet. If no document is present, the check pattern will be printed sheet by sheet. This operation will be executed at a rate of one sheet per 5minutes, and will be ended at a total of 10 sheets.

3. 7. Memory clear

This mode is used to clear the backup memory and reset to the default settings.

3. 8. Shading mode

The mode is used for the shooting compensation. For reading, set up the special original paper. The shooting compensation memorizes the reference data of white and black for reading. Moreover, the memorized data is not erased even if memory clear mode is executed.

3. 4. Panel key test

This mode is used to check whether each key operates properly or not. Press the key on the operation panel, and the key will be displayed on the display. Therefore, press all keys. At this time,finally press the STOP key. When the STOP key is pressed, the keys which are not judged as "pressed" will be printed on the result list. LED port of the contact image sensor (CIS) is kept on during the term from when start of the panel test mode to end with the STOP key.

3. 9. All black print

This mode is used to check the state of the printing head and intentionally overheat it. Whole dots are printed over the interval of 2 m. If it is overheated or the printing sheet is jammed, press STOP key for the end.

3. 5. Check pattern

This mode is used to check the state of the printing head. It is ended with the following pattern printed on one printing sheet.

3. 10. Auto feeder mode

In this mode, a document is inserted and discharged to check the auto feed function. After this mode is started, set a document, and the document feed will be automatically tested.

1 Longitudinal stripe 2 Approx. 30 mm 2 Full black
2 black dots and 2 white dots are repeatedly progressed on one line. Approx. 30 mm

3. 11. Message print

Used to print the displayed message of communication for translate each language.
3. 12. Ring & Dial free
Used to reject dial tone check while autodialing is carried out. And used to change the bottom Ring frequency of auto-receiving to 13Hz.
3. 13. Flash memory check
Data is written into and read from the flash memory to check the data conformity. When the unit enters this mode, the check is started.
3. 14. Flash memory clear
Data in the flash memory is cleared (memory clear). When the unit enters this mode, the check is started. The result is announced by the buzzer beeps. The result of check is printed. Beeps 0 No error 1 Memory error
UX-470DE FO-880DE/NX-670DE 4. How to make soft switch setting
To enter the soft switch mode, make the following key entries in sequence.

Press FUNCTION

DATA No.

Press FUNCTION key.

S F T SW-A1 = S F T SW-A1 = 0 0

Press key. key.

S F T SW-A1 = 0 0

Bit1 - 8 are set.

Press START key during setting.

S F T SW-A2 = 0 0

Soft SW-A2 - SW-M2 are set.

S F T SW-M2 = 0 0

To finish the settings halfway between SW-A1 and SW-M2, press the STOP key. In this case, the setting being done to the SW No. on display will be nullified while settings done to the preceding SW Nos. remain in effect. When the COPY key is pressed, the contents of soft switches are printed.
The soft switch mode is terminated.
UX-470DE FO-880DE/NX-670DE 5. Soft switch description Soft switch
SW DATA NO. NO. SW l A8 ITEM Protect from echo Forced 4800 BPS reception Footer print Length limitation of copy/send/receive CSI transmission DIS receive acknowledgement during G3 transmission Non-modulated carrier for V29 transmission modem EOL detect timer Modem speed 1 SW l ASW l ASW l A3 SW l AError criterion Anti junk fax check Protocol monitor (error print) Protocol monitor Line monitor Digital line equalization setting (Reception) Reserved Reserved Digital cable equalizer setting (Reception for Caller ID) No. 5 No. ~ 20 % Yes 7.2km 5 ~ 10 % No 0km MR coding Reserved Reserved Reserved Reserved Reserved Signal transmission level No. = Binary input 1 Senders information transmit H2 mode Communication error treatment in RTN sending mode (reception) CNG transmission CED tone signal interval No. 1 No. 2 No No. 1 No. 2 No. 3 No. 4 No No No communication error No Yes 25 s No transmitted Twice No Yes Yes No limit Switch setting and function 1 Yes No No Copy/send: 60cm Receive: 1.5m Transmitted NSF: Once DIS: Twice No 13 s V.1 Yes Yes Communication error Yes 1000ms 750ms Yes 500ms 75ms 0km OPTION V.27 ter 0 DE Initial setting Remarks
Printed at com. error Yes Yes 7.2km No. 1 No. 1

SW-A6 No. 1 Auto gain control (MODEM) When this mode is enabled, if the reception signal level is under 31dBm. The modem itself controls the signal gain automatically. SW-A6 No. 2 End buzzer Setting this bit to 0 will disable the end buzzer (including the error buzzer/ on-hook buzzer). SW-A6 No. 3 Disconnect the line when DIS is received in RX mode Bit1= 0: When DIS signal is received during RX mode, disconnected the line is immediately. Bit1= 1: When DIS signal is received during RX mode, wait the next signal. SW-A6 No. 4 Equalizer freeze control (MODEM) This switch is used to perform reception operation by fixing the equalizer control of modem for the line which is always in unfavorable state and picture cannot be received. * Usually, the control is executed according to the state of line where the equalizer setting is changed always. SW-A6 No. 5 Equalizer freeze control 7200BPS only Setting which specifies SW-A3 No. 6 control only in the condition of 7200BPS modem speed. SW-A6 No. 6 CNG transmission in manual TX mode When set to "1", fax transmit the CNG signal in case of manual transmission mode (User press the START key after waiting the fax answering signal from handset or speaker). SW-A6 No. 7 Initial compression scheme for sharp fax in TX mode When set to "0", if the other fax is Sharp model, fax transmit the document by H2 mode. When set to "1", even if the other fax is Sharp model, fax transmit the document by MR mode. SW-A6 No. 8 Reserved Set to "0". SW-B1 No. 1 ~ No. 4 Reserved Set to "0". SW-B1 No. 5 ~ No. 8 Recall times Choice is made as to how many redials there should be. SW-B2 No. 1 Dialing pause (sec/pause) Pauses can be inserted between telephone numbers of direct dial connection. Selection of 4 sec or 2 sec pause is available. SW-B2 No. 2 Dial tone detection (before auto dial) Used to set YES/NO of dial tone detection in auto dialing. SW-B2 No. 3 Reserved Set to "0". SW-B2 No. 4 Busy tone detection (after auto dial) Used to set YES/NO of busy tone detection after auto dialing. SW-B2 No. 5 ~ No. 7 Reserved Set to "0". SW-B2 No. 8 PBX connection Used to select according to the connected line: PBX (Private Branch Exchange). SW-B3 No. 1, No. 2 PBX recall function (R key select) Used to set the operation mode of PBX recall when the R key is pressed. Setting is made according to the type of PBX. No. 1=1, No. 2=1: Time break recall (=Flash) is performed. No. 1=1, No. 2=0: Earth recall is performed. SW-B3 No. 3 Reserved Set to "0". SW-C1 No. 6 Half tone gray scale selection Used to determine the reading gray scale in half tone mode. When set to "0", gray scale is 64 levels. When set to "1", gray scale is 16 levels. SW-B3 No. 4, No. 5 PBX select Used to select the operation mode of PBX recall in auto dialing. No. 4=1, No. 5=1: Time break recall (=Flash) is performed before dialing. No. 4=1, No. 5=0: Earth recall is performed before dialing. No. 4=0, No. 5=0: The PBX ID digit is automatically added when dialing to external line. PBX ID is up to 3 digits and entered in Option settings mode. SW-B3 No. 6 ~ No. 8 Reserved Set to "0". SW-B4 No. 1, No. 2 Reserved Set to "0". SW-B4 No. 3 Dial mode When using the pulse dial, set to 0. When using the tone dial, set to 1. SW-B4 No. 4 Pulse Tone change function by key key from the

[3] Troubleshooting

Refer to the following actions to troubleshoot any of the problems mentioned in 1-4. [1] [2] [3] [4] A communication error occurs. Image distortion produced. Unable to do overseas communication. Communication speed slow due to FALLBACK.
Apply line equalization SOFT SWITCH A5-1, 2.
May be used in case [1] [2] [3] [4].
Slow down the transmission speed SOFT SWITCH A2-1, 2, 3,
4. May be used in case [2] [3].

Replace the TEL/LIU PWB.

May be used in all cases.
Increase the transmission level SOFT SWITCH A4-1, 2, 3, 4, 5.
May be used in case [1] [2] [3].

Replace the control PWB.

May be used in all cases. * If transmission problems still exist on the machine, use the following format and check the related matters.
Decrease the transmission level SOFT SWITCH A4-1, 2, 3, 4,
5. May be used in case [3].

TO: CC: FM:

ATT: ATT:
Ref.No. : Date Dept Sign : : : Ref.No.: Date: Tel No. Fax No. Model name Tel No. Fax No. Model name Phase: A, B, C, D.

From: Mr. Our customer

***** Facsimile communication problem ***** Fax Tel No.: Name Address Contact person Name Address Contact person Line: Domestic / international Reception / Transmission

Other party

Problem mode
Frequency: Confirmation item
Model: G3 Automatic reception / Manual reception Automatic dialing / Manual dialing / Others % ROM version:

Our customer

Please mark problem with an X. No problem is: 0. A1 A2 B1 B2 C1 C2 D1 D2 E1 E2 ) dB at our

C1 C2 E1 E2 D1

Our service

Comment

Other party's service
Transmission level setting is ( customer Transmission level ( ) dBm Reception level ( ) dBm By level meter at B1 and B2

Countermeasure

**** Please attach the G3 data and activity report on problem. **** * Please complete this report before calling the TAC hotline if problem still occurs.

[4] Error code table

1. Communication error code table G3 Transmission
Code Final received signal Incomplete signal frame NSF, DIS CFR FTT MCF PIP or PIN RTN or RTP No signal or DCN Error Condition (Receiver side) Cannot recognize bit stream after flag Cannot recognize DCS signal by echo etc. Cannot recognize NSS signal (FIF code etc) Disconnects line during reception (carrier missing etc) Disconnects line by fall back Disconnects line during reception of multi page Cannot recognize NSS, DCS signal in the case of mode change The line is hung up without replying to telephone request from the receiving party. Cannot recognize NSS, DCS signal after transmit RTN or RTP signal. No response in receiver side or DCN signal received* (transmitter side) Owing to error in some page the error could not be corrected although the specified number of error retransmissions were attempted. Error occurred after or while reception by the remote (receiving) machine was revealed to be impossible. Error occurred just after fallback. Error occurred after a response to retransmission end command was received.

LCD PWB

POWER SUPPLY PWB PANEL PWB TX/RX MOTOR AC CORD

Fig. 1

1) Control PWB
The control PWB controls peripheral PWBs, mechanical parts, transmission, and performs overall control of the unit. This machine employs a 1-chip modem (R96V24) which is in-stalled on the control PWB.

Copy operation

To make a copy on this facsimile, the COPY key is pressed when the machine is in stand-by with a document on the document table and the telephone set is in the on-hook state. First, depression of the COPY key advances the document to the scan line. Similar to the transmitting operation, the image signal from the CIS is converted to a binary signal in the DMA mode via the 1 chip fax engine (FC100M) which is then sent to the image buffer of the RAM. Next, the data is transferred to the recording processor in the DMA mode to send the image data to the thermal head which is printed line by line. The copying takes place as the operation is repeated.

2) TEL/LIU PWB

This PWB controls connection of the telephone line to the unit.

3) Power supply PWB

This PWB provides voltages of +5V and +24V to the other PWBs.

4) Panel PWB

The panel PWB allows input of the operation keys.

5) LCD PWB

This PWB controls the LCD display.
[2] Circuit description of control PWB
Fig. 2 shows the functional blocks of the control PWB, which is composed of 5 blocks.
3) 27C020 (IC4): pin-32 DIP (ROM)
EPROM of 2Mbit equipped with software for the main CPU.
4) W24010S-70LE (IC1): pin-32 SOP (SRAM)
Line memory for the main CPU system RAM area and coding/decoding process. Used as the transmission buffer. Memory of recorded data such as daily report and auto dials. When the power is turned off, this memory is backed up by the lithium battery.

MAIN CONTROL BLOCK

(3) ROM
5) KM29W040T (IC2): pin-44 TSOP (FLASH MEMORY)

MODEM BLOCK

A 4 Mbit NAND FLASH MEMORY to store the voice and image data when using memory functions.

(1) FC100M

(2) MODEM

(4) SRAM

(5) FLASH MEMORY
Fig. 2 Control PWB functional block diagram
2. Description of each block (1) Main control block
The main control block is composed of ROCKWELL (CONEXANT) 1 chip fax engine (FC100M), ROM (2Mbit), SRAM (1Mbit), FLASH MEMORY (4Mbit) and Modem (R96V24). Devices are connected to the bus to control the whole unit.
1) FC100M (IC8) : pin-144 QFP (FAX CONTROLLER) 2) R96V24 (IC5) : pin-100 QFP (MODEM)
The FAXENGINE Integrated Facsimile Controllers. FC100M, contains an internal 8 bit microprocessor with an external 2 Mbyte address space and dedicated circuitry optimized for facsimile image processing and facsimile machine control and monitoring.
MIRQN A[23:0] D[7:0] RDN WRN ROMCSN CSN[1:0] MCSN SYNC REGDMA WAITN RASN CASN[1:0] DWRN TONE

OPI[2]/GPIO[23]/ SSCLK1 OPI[3]/GPIO[24] LEDCTL LCDCS GPIO[0] GPIO[1]/SASTXD GPIO[2]/SASRXD GPIO[3]/SASCLK GPIO[4]/CPCIN GPIO[5]/SSCLK2 GPIO[6]/SSTXD2 GPIO[7]/SSRXD2 GPIO[8]/FWRn GPIO[9]/FRDn GPIO[10]/SSSTAT2 GPIO[11]/BE/ SERINP GPIO[12]/CS[2]n GPIO[13]/CS[3]n GPIO[14]/CS[4]n GPIO[15]/CS[5]n GPIO[16]/IRQ[8] GPIO[17]/IRQ[5]n GPIO[18]/IRQ[9]n GPIO[19]/RDY/ SEROUT GPIO[20]/ALTTONE SM[3:0]/GPO[7:4] PM[3:0]/GPO[3:0] TONE -Vref/CLREF ADXG ADGA ADVA ADGD +Vref VIN THADI VSS(12)
107 [103:106] [115:118] 65 7,21,28,45, 53,56,64,88, 95,108,132, 134 14,32,41,48, 81,102,123, 114
I/O I/O O O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O O O O I I
Operator Panel Interface 2XC (Pullup, Hysteresis In) Keyboard return [2] or GPIO[23] or SSCLK1 (for SSIF1) HU 2XC (Pullup, Hysteresis In) Keyboard return [3] or GPIO[24] 4XC Indicates outputs OPO[7:0] are for LEDs. 1XC LCD chip select. General Purpose I/O H 2XC (Hysteresis In) GPIO[0]. H 2XC (Hysteresis In) GPIO[1] or SASTXD (for SERIF). H 2XC (Hysteresis In) GPIO[2] or SASRXD (for SERIF). H 2XC (Hysteresis In) GPIO[3] or SASCLK (for SERIF). H 2XC (Hysteresis In) GPIO[4] or Calling Party Control Input. H 2XC (Hysteresis In) GPIO[5] or SSCLK2 (for SSIF2). H 2XC (Hysteresis In) GPIO[6] or SSTXD2 (for SSIF2). H 2XC (Hysteresis In) GPIO[7] or SSRXD2 (for SSIF2). H 2XC (Hysteresis In) GPIO[8] or flash write enable signal for NAND-type flash memory. H 2XC (Hysteresis In) GPIO[9] or flash read enable signal for NAND-type flash memory. H 2XC (Hysteresis In) GPIO[10] or SSSTAT2 (for SSIF2). H 1XC (Hysteresis In) GPIO[11] or bus enable or serial port data input for autobaud detection. H 2XC (Hysteresis In) GPIO[12] or I/O chip select [2]. H 2XC (Hysteresis In) GPIO[13] or I/O chip select [3]. H 2XC (Hysteresis In) GPIO[14] or I/O chip select [4]. H 2XC (Hysteresis In) GPIO[15] or I/O chip select [5]. H 1XC (Hysteresis In) GPIO[16] or external interrupt 8. H 1XC (Hysteresis In) GPIO[17] or external interrupt 5. H 1XC (Hysteresis In) GPIO[18] or external interrupt 9. H 1XC (Hysteresis In) GPIO[19] or ready signal or Serial port data output for autobaud detection. H 1XC (Hysteresis In) GPIO[20] or ALTTONE. Miscellaneous 1XC Programmable: scan motor control pins or GPO pins. 1XC Programmable: print motor control pins or GPO pins. 1XC Tone output signal. Power, Reference Voltages, Ground -VR Negative Reference Voltage for Video A/D or Reference Voltage for the Clamp Circuit. VXG A/D Internal GND. (NOTE: This pin requires an external 0.22F decoupling capacitor to ADGA.) VADG A/D Analog Ground VADV A/D Analog Power VADG A/D Digital Ground +VR Positive Reference Voltage for Video A/D. VA Analog Video A/D input. TA Analog Thermal A/D input. Power and Ground Digital Ground

VDD(8)

Digital Power

VBAT VDRAM

Battery Power DRAM Battery Power

Photo Coupler

Fig. 7
2-1. Noise filter circuit
The input noise filter section is composed of L1, C1 and C15 that reduces normal mode noise from the AC line and common mode noise to the AC line.
The overcurrent protection is performed by bringing Q1 to OFF state through detection of voltage increase in the auxiliary winding of T1 by ZD2, R5 and R6. The overvoltage protection is performed by operating the overcurrent protection circuit through destruction of zener diode ZD4 and shortcircuiting of load.
2-2. Rectifying/smoothing circuit
The AC input voltage is rectified by diode D1, 2, 3, 4 and smoothed by capacitor C2 to supply DC voltage to switching circuit section. Power thermistor TH1 suppresses inrush current at power switch-on.

2-4. +5V circuit

Each DC voltage supplied by rectifying the output of transformer T1 with diode D8 is stabilized by 3-terminal regulator IC1.

2-3. Switching circuit

This circuit employs the self excited ringing choke convertor (RCC) system. In this system, the DC voltage supplied from the rectifying/smoothing section is converted to be the high frequency pulses by ON/OFF repetition of MOS FET Q1. Energy is charged in the primary winding of T1 during ON period of Q1, and discharged to the secondary winding during OFF period of Q1. The output voltage is controlled by adjusting ON period of Q1 which changes charge time of C8 through operation of photo-coupler PC1 from +24V output.
[5] Circuit description of CIS unit

1. CIS

Cis is an image sensor which puts the original paper in close contact with the full-size sensor for scanning, being a monochromatic type with the pixel number of 1,728 dots and the main scanning density of 8 dots/mm. It is composed of sensor, rod lens, LED light source, light-conductive plate, control circuit and so on, and the reading line and focus are previously adjusted as the unit. Due to the full-size sensor, the focus distance is so short that the set is changed from the light weight type to the compact type.

T 1.6s CISCLK

2. Waveforms
The following clock is supplied from FC100M of the control board, and VO is output.

5ms Approx.5V 0V

2V(TYP) (White original paper)

Fig. 8

(1-2I) (3-2A) +5V C156 1000P C172 1000P C191 1000P C154 1000P C189 1000P C187 1000P C170 1000P C151 1000P

C239 1000P

+5V R208 10K (2-6A)(3-5A) D[7~0]
D0 D1 D2 D3 D4 D5 D6 D7 +5V

C155 1

[1] Control PWB circuit Main control block

C153 1

C150 1

C183 1

C182 0.1

CCRAx 4

C184 1

C192 1

53,56 64,88 7,134

132 95,108

DG A[18~0]
137 RAx 130 SYSCLK 133 MIRQ R30K 129 R177 10K 131 C171 1000P R10K
45 D0 D1 D2 D3 D4 D5 D6 D7 VSS VSS VSS VSS VSS VSS VSS VSS TSTCLK SYSCLK MIRQ DEBUG RESET TEST

123 140

VDD VDD VDD VDD VDD VDD VDD VDD ADVA ADXG

69 ADGA 72 ADGD

(2-6A)(3-3A)
(3-3A) (4-4D) (4-3D) A B C D
(4-3D) CNLIUB-2 (5-3E) CNPW-9
C224 100P MDMRST RBNSNS FRSNS ORGSNS RLYCNT
RR203 30K R201 30K RA10 270x3 R231 30K

CNLIUB-4

CNLIUA-11 CNLIUA-8 CNLIUA-5 CNLIUA-4 CNLIUA-3
GPIO20 GPIO19 GPIO18 GPIO17 GPIO16 GPIO15 GPIO14 GPIO13 GPIO12 GPIO11 GPIO10 GPIO9 GPIO8 GPIO7 GPIO6 GPIO5 GPIO4 GPIO3 GPIO2 GPIO1 GPIO0

IC8 FC100-M

CHAPTER 6. CIRCUIT SCHEMATICS AND PARTS LAYOUT
XIN +VREF VREF/CLREF VIN THADI TONE GPO0 GPO1 GPO2 GPO3 VDRAM OPI0 OPI1 OPI2 OPI3 LEDCTL LCDCS OPO0 OPO1 OPO2 OPO3 OPO4 OPO5 OPO6 OPOSMSMSMSMRA470x+5V

C217 C215 C213 C212

A23 A22 A21 A20 A19 A18 A17 A16 A15 A14 A13 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 N.M. R260 A18 A17 RA16 RA15 A14 RA6 270x4 A13 A12 A11 RA8 A10 270x4 A9 A8 A7 A6 RA9 270x4 A5 A4 A3 RA11 A2 270x4 A1 A0 RG RC240 68P

CNCIS-5 CNCIS-4

VIDCTL0 VIDCTL1 CLK1 CLK1 CLK2 START
RD WR ROMCS C241 68P CE1 MCS J H I DGDG
(2-3A)(3-3A) (2-4C)(3-3A) (2-4A) (2-4D) (3-3A)
CNTH-12 CNTH-11 CNTH-4 CNTH-3 CNTH-14 CNTH-15 CNTH-13

BATRST 61

76 R77 VTHON RR258 10K PSAVE 78 RMONITOR R79 (6-3A) DPON 80 RSPMUTE 82 RC228 (6-2I) 100P FREADY 83 R172 R174 (2-4F) 470 10K FRD 84 C238 (2-4F) RA15 FWR 85 100P (2-5F) 270x4 FCLE 86 (2-5F) C218 FALE 87 100P (2-5F) RCML DG 89 R180 30K RHS 90 HS R179 30K 91 RA7 470x4 R178 30K CI 92 R175 3.3K TELMUTE 93 R94 LEDON (5-5F) FCS R96 100Px(2-4F) L108 DG HMCISCLK RPHIT 101 RC109 N.M. C110 RA12 100xSTRBSTRBSTRBSTRB1 L29 PCLK RR30 DATA R31 LATCH 37 R209 10K RD WR ROMCS CS1 CS0 MCS SYNC REGDMA WAIT RAS CAS0 CAS1 DWR WRPROT R235 10M RA5 270x4 R133 1M R252 220K

C210 22P

STRB3 STRB2 STRB1 STRB0 PCLK PDAT PLAT STRBPOL
63 VBAT C188 2200P 62 PWRDWN C185 22P 60 XOUT

X3 32.768kHz

R11 100K

R6 100K

R10 100K

R3 100K

R9 100K

R4 100K

R8 100K

R5 100K

R7 100K

16 VCC 9 A0 DA1 DA2 DA3 DN.C. D5 D6 D7 D8 D9 GND 8 DG CNPN-11 CNPN-10 CNPN-7 CNPN-6 CNPN-5 SEN4 E +5V DG C2 22/50 C1 2200P 10

IC1 HC147

RS E +5V DG R/W R1 6.2K R2 1K DG VO
CNLCD-4 CNLCD-6 CNLCD-2 CNLCD-1 CNLCD-5

ORGSNS ORGSNS CNPN-8

FRSNS FRSNS CNLCD-3 DG CNPN-9

CNPN 15

KEN4 KEN3 KEN2 KEN1 DG DG +5V ORGSNS FRSNS E SEN4 SEN0 SEN1 SEN2 SEN3
CNLCD GND 1 +5V 2 VO 3 RS 4 R/W 5 E 6 N.C. 7 N.C. 8 N.C. 9 N.C. 10 LDLDLDLD7 14
Note: Since the parts of PWB can not be supplied, change it as a unit.

A B C D E F G H I

PARTS GUIDE
UX-470 FO-880 MODEL NX-670

Cabinet, etc.

Packing material & Accessories

Top cover and sub frame

Control PWB unit

Upper cabinet

TEL-Liu PWB unit

Document guide upper

Power supply PWB unit

Drive unit

Because parts marked with " " is indispensable for the machine safety maintenance and operation, it must be replaced with the parts specifi to the product specification.

[1] Cabinet, etc.

1 TOP COVER/ SUB FRAME 48

DOCUMENT GUIDE UPPER

DRIVE UNIT

NO. PARTS CODE

PRICE RANK NEW MARK PART RANK

DESCRIPTION

[1] Cabinet,etc.
1 DCEKP478BFF07 DCEKP478BFF09 DCEKP478BFF04 QCNW-4935XHZZ MLEVP2297XHZZ MSPRT3069XHFJ NROLR2375XHZZ NSFTP2302XHZZ PGIDM2538XHZZ CCNW-202AFF01 CGERH2444XHY1 GCABB2325FFSC GCABB2325FFSE LANGF2817XHFW LBSHP2088AXZZ MLEVP2290XHZZ MLEVP2292XHZZ MLEVP2294XHZZ MLEVP2295XHZZ MLEVP2296XHZZ MSPRD3082XHFJ MSPRD3073XHFJ MSPRP3054XHFJ MSPRP3055XHFJ NGERH2445XHZZ NROLR2410XHZZ NSFTM2311XHZZ PSHEZ3428XHZZ LFRM-2198XHZZ MSPRC3103XHFJ MSPRC3059XHFJ MSPRC3102XHFJ MSPRC3061XHFJ PGIDM2531XHZZ PGIDM2532XHZZ QCNW-4936XHZZ RHEDZ2058XHZZ PGIDM2529XHZZ PGIDM2530XHZZ QCNW-4850XHZZ RUNTZ2037XHZZ CPWBS3025FF01 DCEKL457BFF22 LPLTM2995XHFW MSPRC3057XHFJ PCOVP2122XHZZ QACCV662AXHZZ QCNW-4971XHZZ RCORF2064XHZZ MLEVP2302XHZZ HPNLH2389XHSY HPNLH2389XHS7 HPNLH2391XHSE GLEGG2063FFZZ PSHEZ3410FFZZ RDENT2137XHZZ PCUSS2120XHZZ PSHEZ3429XHZZ MSPRD3104XHFJ PSHEZ3432XHZZ PSHEZ3425XHZZ RCORF2063XHZZ TLABM4878FFZZ PSHEZ3436XHZZ TLABS4917FFZZ RCORF2103XHZZ XEBSD30P10000 XBBSD30P06000 XBPSN40P06K00 XHBSD30P05000 XEBSD30P08000 XBPSD30P06K00 N N N N E E E C C C C C C C C D D C C C C C C C C C C C C C C C C C C C C C C C B C C C B E E C C C B C B C D D D C C E C C C C C B D C D B C C C C C C Operation panel unit Operation panel unit Operation panel unit Panel cable Cover switch lever Cover switch spring Feed roller Feed roller shaft Original paper guide Speaker assy BT gear assy Lower cabinet Lower cabinet Platen lock bracket Transfer bearing Film sensor lever B PE sensor lever B P-IN sensor lever B Platen lock lever,left Platen lock lever,right Platen lock spring Sensor spring B Panel lock lever spring Speaker holder plate spring Back roller gear PO roller Film guide shaft Sheet A Head frame Head spring F Head spring B Head spring E Head spring D Head guide,left Head guide,right Head cable Thermal head CIS guide,left CIS guide,right CIS cable CIS unit Control PWB unit(Without ROM) TEL-Liu PWB unit Bottom plate CIS spring Head cover AC cord assy Head earth cable Core(TRA31) Hook switch lever Decoration panel Decoration panel Decoration panel Rubber leg Jack sheet Power supply PWB unit Head cushion Head guide sheet Film sensor lever spring Bottom plate sheet Shield sheet Core(TRA20) Panel pop label CIS protect sheet BZT label Core Screw(3x10) Screw(3x6) Screw(4x6) Screw(3x5) Screw(3x8) Screw(3x6) [470] [880] [670]

[470/670] [880] [470] [880/670] [470/670] [880]

AN AE AA

[4] Document guide upper
LPLTG2911XHZZ LPLTP2908XHZZ MSPRC3071XHFJ MSPRP3079XHFJ MSPRT2951XHZZ NBRGP2141XHZZ NGERH2445XHZZ NROLP2334XHZA NROLP2406XHZZ NROLR2411XHZZ NSFTZ2257XHZZ PGIDM2536FFZZ AE AE AB AE AC AH AB AC AD AV AG C C C C C C C C C C C C Separator rubber Separator plate Pinch roller spring Paper feed spring Separate spring Transfer bearing Back roller gear Pinch roller Guide roller Back roller Pinch roller shaft Document guide upper

[5] Drive unit

30 B2 CGERH2459XH01 CLEVP2298XH01 CLEVP2299XH01 CLEVP2300XH01 CLEVP2303XH01 LFRM-2200XHZZ LPLTM2994XHFW MCAMP2025XHZZ MCAMP2026XHZZ MLEVP2301XHZZ MSPRD3070XHFJ NGERH2280XHZZ NGERH2311XHZZ NGERH2446XHZZ NGERH2447XHZZ NGERH2448XHZZ NGERH2449XHZZ NGERH2450XHZZ NGERH2451XHZZ NGERH2452XHZZ NGERH2454XHZZ NGERH2461XHZZ QCNW-4933XHZZ QSW-F2224SCZZ RMOTZ2145XHZZ XEBSD30P10000 AM AC AC AC AC AB AE AB AB AB AB AC AD AB AB AB AB AB AB AB AB AB AC AE BA AA C C C C C C C C C C C C C C C C C C C C C C C B B C Slip gear assy Planet gear lever A assy Planet gear lever B assy Planet gear lever C assy Planet gear lever D assy Drive frame Motor plate Cam A Cam B Link lever Cam hold spring Idler gear B Reduction gear C Reduction gear,1 Reduction gear,2 Reduction gear,3 Reduction gear,4 Reduction gear,5 Idler gear,30Z Idler gear,52Z Take up gear Reduction gear,6 Cam switch cable Cam switch Motor Screw(3x10)
[6] Packing material & Accessories

(4) (1) (3)

1 SPAKC046BFFZZ SPAKC048BFFZZ SPAKC050BFFZZ TLABM4915FFZZ TLABM4918FFZZ TLABM4921FFZZ TINSG3963FFZZ TINSG3964FFZZ TINSG3965FFZZ TLABH4834FFZZ TLABH4880FFZZ CPLTP3002XHB2 TLABH4752XHZZ LPLTP3003XHSA PHOP-2102XHZZ SPAKA490AFFZZ SPAKA489AFFZZ SPAKA481AFFZZ SPAKA480AFFZZ QCNW-4649FFZZ QCNW-3976XHBG QCNW-3976XHOW NGERH2455XHZZ NGERH2456XHZZ PRBNN2015SCZZ SPAKP3385FFZZ DUNTK419BFFBG DUNTK419BFFWH TLABH4835XHZZ TLABM4923FFZZ TLABM4920FFZZ TLABH4899XHZZ N N N N N N N N N D D D D D D D D D D D E D C C D D D D C C C C C S D E E D D D D Packing case Packing case Packing case Box label Box label Box label Operation manual Operation manual Operation manual Rapid key labels Rapid key labels Imaging film cartridge and label assy Film set label Paper tray extension Original document support Pad B Pad A Packing add.,right Packing add.,left Telephone line cord Handset cord Handset cord Imaging film gear A Imaging film gear B Imaging film(Initial starter roll 10m) Vinyl cover Handset Handset Caution label A Pop label Pop label Caution label B [470] [880] [670] [470] [880] [670] [470] [880] [670] [470] [880/670]

163 VHIKM29W040-1 VHIULN2003ANS QSOCZ0115SC32 VHI27020FKW0B VHI27020FKX0G VHIR96V24FC1M VHITC74HCU04F VHIPST596CMT1 VHIR96V24FC1M VHIMC34119DR2 VHIHCF4051M1T VHIHCF4053M1T VHINJM2904M-1 VHIHCF4053M1T VHINJM2902M-1 RCILZ2145XHZZ RCILZ2145XHZZ VRS-TS2AD121J VRS-TS2AD000J VP-1M3R3J0000 RCILZ2145XHZZ RCILZ2104SCZZ VRS-TS2AD000J RCILZ2145XHZZ VRS-TS2AD000J RCILZ2145XHZZ VHPSG206S//-1 VS2SA1037KS-1 VS2SC2412KR-1 VSDTD114EK/-1 VS2SA1037KS-1 VRS-TS2AD271J VRS-TS2AD000J VRS-TS2AD103J VRS-TS2AD151J VRS-TS2AD151J VRS-TS2AD151J VRS-TS2AD151J VRS-TS2AD151J VRS-TS2AD151J VRS-TS2AD512J VRS-TS2AD303J VRS-TS2AD104J VRS-TS2AD271J VRS-TS2AD223J VRS-TS2AD000J VRS-TS2AD000J VRS-TS2AD151J VRS-TS2AD151J VRS-TS2AD000J VRS-TS2AD471J VRS-TS2AD271J VRS-TS2AD271J VRS-TS2AD271J VRS-TS2AD271J VRS-TS2AD271J VRS-TS2AD104J VRS-TS2AD100J VRS-TS2AD271J VRS-TS2AD104J VRS-TS2AD303J VRS-TS2AD105J VRS-TS2AD271J VRS-TS2AD271J VRS-TS2AD271J VRS-TS2AD271J VRS-TS2AD103J VRS-TS2AD393J VRS-TS2AD393J VRS-TS2AD103J VRS-TS2AD100J VCKYTV1HB102K VCKYTV1HB102K VRS-TS2AD333J VRS-TS2AD101J VRS-TS2AD680J VRS-TS2AD151J VRS-TS2AD471J VRS-TS2AD150J VRS-TS2AD471J AV AE AC N N N N B B C B B B B B B B B B B B B C C C C C C C C C C C B B B B B C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C IC(KM29W040T) IC(ULN2003ANS) IC socket(32pin) IC,EPROM(2MB) IC,EPROM(2MB) IC(R96V24)(Within IC5 and IC8 pair) IC(TC74HCU04) IC(PST596CNR) IC(FC100M)(Within IC5 and IC8 pair) IC(MC34119DR2) IC(HCF4051) IC(HCF4053) IC(NJM2904) IC(HCF4053) IC(NJM2902M) Coil(Z2145) Coil(Z2145) Resistor(1/10W 120 5%) Resistor(1/10W 0 5%) Coil(3.3H) Coil(Z2145) Coil(Z2104) Resistor(1/10W 0 5%) Coil(Z2145) Resistor(1/10W 0 5%) Coil(Z2145) Photo transistor(SG206S) Transistor(2SA1037KS) Transistor(2SC2412K) Transistor(DTD114EK) Transistor(2SA1037KS) Resistor(1/10W 270 5%) Resistor(1/10W 0 5%) Resistor(1/10W 10K 5%) Resistor(1/10W 150 5%) Resistor(1/10W 150 5%) Resistor(1/10W 150 5%) Resistor(1/10W 150 5%) Resistor(1/10W 150 5%) Resistor(1/10W 150 5%) Resistor(1/10W 5.1K 5%) Resistor(1/10W 30K 5%) Resistor(1/10W 100K 5%) Resistor(1/10W 270 5%) Resistor(1/10W 22K 5%) Resistor(1/10W 0 5%) Resistor(1/10W 0 5%) Resistor(1/10W 150 5%) Resistor(1/10W 150 5%) Resistor(1/10W 0 5%) Resistor(1/10W 470 5%) Resistor(1/10W 270 5%) Resistor(1/10W 270 5%) Resistor(1/10W 270 5%) Resistor(1/10W 270 5%) Resistor(1/10W 270 5%) Resistor(1/10W 100K 5%) Resistor(1/10W 10.0 5%) Resistor(1/10W 270 5%) Resistor(1/10W 100K 5%) Resistor(1/10W 30K 5%) Resistor(1/10W 1.0M 5%) Resistor(1/10W 270 5%) Resistor(1/10W 270 5%) Resistor(1/10W 270 5%) Resistor(1/10W 270 5%) Resistor(1/10W 10K 5%) Resistor(1/10W 39K 5%) Resistor(1/10W 39K 5%) Resistor(1/10W 10K 5%) Resistor(1/10W 10.0 5%) Capacitor(50WV 1000PF) Capacitor(50WV 1000PF) Resistor(1/10W 33K 5%) Resistor(1/10W 100 5%) Resistor(1/10W 68 5%) Resistor(1/10W 150 5%) Resistor(1/10W 470 5%) Resistor(1/10W 15 5%) Resistor(1/10W 470 5%) [IC2] [IC3] [IC4] [IC4][470] [IC4][880/670] [IC5] [IC6] [IC7] [IC8] [IC9] [IC10] [IC11] [IC12] [IC13] [IC14] [L100] [L101] [L102] [L103] [L104] [L105] [L106] [L107] [L108] [L109] [L110] [PI1] [Q100] [Q102] [Q103] [Q105] [R100] [R101] [R102] [R103] [R104] [R105] [R106] [R107] [R108] [R109] [R111] [R113] [R114] [R115] [R116] [R117] [R118] [R119] [R120] [R121] [R122] [R123] [R124] [R126] [R127] [R128] [R129] [R130] [R131] [R132] [R133] [R134] [R135] [R136] [R137] [R138] [R139] [R140] [R141] [R142] [R143] [R145] [R146] [R147] [R148] [R149] [R150] [R151] [R153]

! ! ! ! ! ! ! ! !

AC AC AC AC AC AH AE AH AE AG AG AE AB AD AB AB AB AB AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA
PRICE RANK NEW MARK PART RANK Resistor(1/10W 2.2K 5%) Resistor(1/10W 75K 5%) Resistor(1/10W 30K 5%) Resistor(1/10W 0 5%) Resistor(1/10W 24K 5%) Resistor(1/10W 3.3K 5%) Resistor(1/10W 91K 5%) Resistor(1/10W 3.3K 5%) Resistor(1/10W 56K 5%) Resistor(1/10W 10.0 5%) Diode bridge(S1ZB60) Hook switch Transformer(I2142) Varistor(DSS301L) Zener diode(MTZJ30B) Zener diode(MTZJ6R8B) Zener diode(MTZJ30B) Zener diode(MTZJ3R3B) Zener diode(MTZJ3R3B) Zener diode(MTZJ2R4B) Zener diode(MTZJ2R4B) TEL-Liu PWB unit
VRS-TS2AD222J VRS-TS2AD753J VRS-TS2AD303J VRS-TS2AD000J VRS-TS2AD243J VRS-TS2AD332J VRS-TS2AD913J VRS-TS2AD332J VRS-TS2AD563J VRS-TS2AD100J VHDS1ZB60//-1 QSW-Z2263XHZZ RTRNI2142XHZZ VHVDSS301L/-U VHEMTZJ300B-1 VHEMTZJ6R8B-1 VHEMTZJ300B-1 VHEMTZJ3R3B-1 VHEMTZJ3R3B-1 VHEMTZJ2R4B-1 VHEMTZJ2R4B-1 (Unit) DCEKL457BFF22 AA AA AA AA AA AA AA AA AA AA AC AG AR AF AA AC AA C C C C C C C C C C B B B B B B B B B B B N E [R153] [R154] [R155] [R156] [R158] [R159] [R160] [R166] [R167] [R168] [REC1] [SW1] [T1] [VA1] [ZD2] [ZD4] [ZD5] [ZD6] [ZD7] [ZD10] [ZD11]
[9] Power supply PWB unit
51 0CBUGFM224KR/ 0CBUGZ1186ZZ/ 0CBUGZ1187ZZ/ 0CBUGFF472BQ/ 0CBUGFF223JS/ 0CBUGCM332BJ/ 0CBUGAE331TS/ 0CBUGFF474JA/ 0CBUGZ1188ZZ/ 0CBUGCF104CQ/ 0CBUGCS101AA/ 0CBUGFM104KD/ 0CBUGAB101RV/ 0CBUGFF102BQ/ 0CBPZZ0931ZZ/ 0CBPKZ0194ZZ/ 0CBUBC0125DK/ 0CBUBC0125DK/ 0CBUBC0125DK/ 0CBUBC0125DK/ 0CBUBA0011AL/ 0CBUBC0336AZ/ 0CBUBC0302BZ/ 0CBPJCEJ1601/ 0CBPJCEJ1601/ 0CBPZZ0906ZZ/ 0CBUCB0167AZ/ 0CBUKZ0826ZZ/ 0CBUZZ0156ZZ/ 0CBLRZ6581ZN/ 0CBLRZ6562ZN/ 0CBUDC0163CZ/ 0CBUDC0163CZ/ 0CBUAG0161AC/ 0CBUAC0264AZ/ 0CBUAC0034EZ/ 0CBUAC0034EZ/ 0CBUAC0284BK/ 0CBUAC0284BK/ 0CBUEEC335CF/ 0CBUEEB824CF/ 0CBUEEB824CF/ 0CBUEEB101CT/ 0CBUEEB152CT/ 0CBUEEB223CT/ 0CBUEEB330CT/ 0CBUEEB473CT/ 0CBUEEB471CT/ 0CBUEFDR33DB/ 0CBUEEB390CT/ 0CBUEEB334CT/ AF AL AD AC AC AF AH AF AK AD AD AF AF AD AH AC AD AD AD AD AD AL AE AH AH AH AR AK AN AQ AQ AG AG AQ AD AE AE AF AF AC AC AC AC AC AC AC AC AC AE AC AC C C C C C C C C C C C C C C C C B B B B B B B A A A B C C C C B B B B B B B B C C C C C C C C C C C C Capacitor(RE224-C) Capacitor(KMF400VB-39M 18x20) Capacitor(DE1407-477SL471J2K) Capacitor(AMZ-472K50) Capacitor(ECQB1H223KM3) Capacitor(DE1410-1E332M-KX) Capacitor(LXJ35VB330(M)) Capacitor(ECQV1H474JL3) Capacitor(16YXG2200M(10X28L)) Capacitor(UP050F104Z-B) Capacitor(DD05-989B101K500) Capacitor(PA104-ZC) Capacitor(KME10VB100(M)) Capacitor(AMZ-102K50) Connector(IMSA-9110S-09L) Base post assy(B 2P3-VH) Diode(ERA15-06) Diode(ERA15-06) Diode(ERA15-06) Diode(ERA15-06) Diode(1SS133) Diode(S3L20U-4004P15) Diode(SR140) Current fuse(21501.6 ME600) Current fuse(21501.6 ME600) Circuit protect chip(CCP2E100) IC(UPC29M05HF) Filter(ELF15N003A) Coil(RS208) Heat sink Heat sink Photo coupler(PC123YS) Photo coupler(PC123YS) FET(FS5KM-18A AN) Transistor(2SC1741AS QR) Transistor(2SC1740S) Transistor(2SC1740S) Transistor(2SC2710) Transistor(2SC2710) Resistor(RD50SS-335J) Resistor(RD50SS-824J) Resistor(RD50SS-824J) Resistor(RD16S 101J) Resistor(RD16S 152J) Resistor(RD16S 223J) Resistor(RD16S 330J) Resistor(RD16S 473J) Resistor(RD16S 471J) Resistor(RSMF1TBR33G) Resistor(RD16S 390J) Resistor(RD16S 334J) [C1] [C2] [C3] [C4] [C5] [C7] [C8] [C9] [C10] [C11] [C13] [C15] [C16] [C17] [CN1] [CN2] [D1] [D2] [D3] [D4] [D5] [D7] [D8] [F1] [F2] [F3] [IC1] [L1] [L2] [MT1] [MT2] [PC1] [PC2] [Q1] [Q2] [Q3] [Q4] [Q5] [Q6] [R1] [R2] [R3] [R4] [R5] [R6] [R7] [R8] [R9] [R10] [R11] [R12]

AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C
VRS-TS2AD303J VRS-TS2AD304J VRS-TS2AD332J VRS-TS2AD333J VRS-TS2AD392J VRS-TS2AD393J VRS-TS2AD433J VRS-TS2AD471J VRS-TS2AD472J VRS-TS2AD473J VRS-TS2AD474J VRS-TS2AD512J VRS-TS2AD513J VRS-TS2AD514J VRS-TS2AD562J VRS-TS2AD563J VRS-TS2AD621J VRS-TS2AD680J VRS-TS2AD683J VRS-TS2AD753J VRS-TS2AD754J VRS-TS2AD822J VRS-TS2AD913J VRSTS2AD1373F VRSTS2AD6812F VSBS108////-1 VSDTC114EK/-1 VSDTD114EK/-1 VS2SA1037KS-1 VS2SC2412KR-1 [X] XBBSD30P06000 XBPSD30P06K00 XBPSN40P06K00 XEBSD20P06000 XEBSD30P08000 XEBSD30P10000 XHBSD30P05000 [0] 0CBLRZ6562ZN/
8-120 7-274 7-259 7-304 7-323 8-123 8-125 7-234 7-273 7-311 7-318 7-321 8-117 7-297 7-228 7-229 8-84 7-211 7-238 7-240 7-254 7-255 7-256 7-281 7-285 7-287 7-288 7-313 7-314 8-98 8-99 8-100 7-245 7-301 7-322 7-248 7-277 7-201 7-310 8-93 8-94 7-278 7-294 7-303 8-126 8-108 7-236 7-305 7-272 8-119 7-275 8-103 7-324 8-124 7-296 7-295 8-74 8-75 8-77 8-78 8-79 8-80 8-81 7-190 7-188 7-191 7-189 8-76 1-B3 1-B8 1-B4 3-B1 1-B7 1-B2 2-B2 5-B2 1-B5 9-31
AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AG AA AA AA AA AA AA AA AA AA AA AA AA AA AA AE AB AB AB AB AB AB AC AB AB AD AD AA AA AA AA AA AA AA AA AA AQ C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C B B B B B B B B B B B B C C C C C C C C C C
N N AG AG AG AE AE AH AH AF AA AE AE AG AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA
0CBLRZ6581ZN/ 0CBPJCEJ1601/ 0CBPKZ0194ZZ/ 0CBPZZ0906ZZ/ 0CBPZZ0931ZZ/ 0CBUAC0034EZ/ 0CBUAC0264AZ/ 0CBUAC0284BK/ 0CBUAG0161AC/ 0CBUBA0011AL/ 0CBUBC0125DK/ 0CBUBC0302BZ/ 0CBUBC0336AZ/ 0CBUBDBE2R0C/ 0CBUBDBE200D/ 0CBUBDBE270D/ 0CBUBDBE6R2C/