Do not place this machine on an unstable cart, stand or table. The machine could be seriously damaged if it falls. Never install telephone wiring during a lightning storm. Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. Never touch bare telephone wires or terminals unless the telephone line has been disconnected at the network interface. Use caution when installing or modifying telephone lines. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. Do not use a telephone to report a gas leak in the vicinity of the leak. The power outlet must be installed near the equipment and must be easily accessible.

Table of Contents

A Look at the Operation Panel 1. Installation 7 9
Unpacking Checklist. 9 Attachments. 10 Loading Printing Paper. 13 Connecting the Power Cord. 14 Installing the Print Cartridge. 15 Connecting the Telephone Line Cord. 23 Entering Your Name and Fax Number. 24 Setting the Date and Time. 26 Setting the Reception Mode. 28 Volume Adjustment. 29

2. Sending Faxes

Transmittable Documents. Loading the Document. Adjusting the Resolution and Contrast. Sending a Fax by Normal Dialing. Sending a Fax by Automatic Dialing. Batch Page Numbering. Sending a Fax From Memory.

3. Receiving Faxes

Using FAX Mode. Using TEL Mode. Optional Reception Settings. Substitute Reception to Memory.
4. Making Copies 5. Special Functions
Caller ID (Requires Subscription to Service). 61
Distinctive Ring (Requires Subscription to Service). 66 Blocking Reception of Unwanted Faxes. 68 Polling (Requesting a Fax Transmission). 69
6. Printing Lists 7. Maintenance
Cleaning the Machine. 74 Improving Print Quality. 77

8. Troubleshooting

Problems and Solutions. 82 Messages and Signals. 86 Clearing Paper Jams. 89 Ordering Parts. 91 FCC Regulatory Information. 92

The high-quality fax print setting is initially turned off.

4 times.

1=YES, 2=NO

Press print, or

to turn on high-quality fax to turn it off.

HQ COPY

Connecting the Telephone Line Cord
Insert one end of the line cord into the jack on the back of the machine marked TEL. LINE. Insert the other end into a standard (RJ11C) single-line wall telephone jack.
Setting the dial mode The fax machine is set for tone dialing. If you are on a pulse dial line, you must set the fax machine for pulse dialing. Press the panel keys as follows:

OPTION SETTING

DIAL MODE

1=TONE, 2=PULSE

Select the dial mode: TONE: PULSE:

DISTINCTIVE

to exit.
Entering Your Name and Fax Number
Before you can begin sending faxes, you must enter your name and fax (telephone) number. You also need to set the date and time. Once you enter this information, it will automatically appear at the top of each fax page you send.
Important! FCC regulations require that your name, telephone/fax number, and the date and time appear on each fax message you send. Enter your name and fax number here and set the date and time as explained in the following section to have the fax machine include this information automatically at the top of your fax messages.

ENTRY MODE

OWN NUMBER SET

ENTER FAX #

Enter your fax number by pressing the number keys (max. 20 digits).
To insert a space between digits, press To clear a mistake, press
Enter your name by pressing number keys for each letter as shown in the chart below. Up to 24 characters can be entered. Example: SHARP = 2 777
SPACE = A= B= C= D= E= F= G= H= I = J= K= L= M= N= O= P= Q= R= S= T=

U= V= W= X= Y= Z=

To enter two letters in succession that require the same key, press
entering the first letter.
To clear a mistake, press
To enter a lower case letter, continue pressing the key for the letter until the
lower case letter appears. To enter one of the following symbols, press or repeatedly:. / ! " # $ % & ( ) + + , - : ; < = > ? @ [ ] ^ _ ' { | } ) (

DATE&TIME SET

Setting the Date and Time
The date and time appear in the display and are printed at the top of every page you fax. Set the date and time as shown below.
The currently set date appears (example):

DATE 08-15-2004

Enter a two-digit number for the month (01 for January, 02 for February, 12 for December, etc.). Example: January

DATE 01-15-2004

To correct a mistake, press
then enter the correct number.
to move the cursor back to the mistake and
Enter a two-digit number for the day (01 to 31). Example: the 5th

DATE 01-05-2004

Enter the year (four digits). Example: 2004
The currently set time appears (example):

TIME 12:19 PM

Enter a two-digit number for the hour (01 to 12) and a two-digit number for the minute (00 to 59). Example: 9:25

TIME 09:25 PM

to select A.M. or

to select P.M.

to start the clock.

ANTI JUNK #

Daylight Saving Time
If desired, you can set the clock to move forward and backward automatically at the beginning and end of Daylight Saving Time. Follow these steps:

Display: OPTION SETTING

DAY LIGHT SAVE

to select YES, or

to select NO.

ERROR BEEP

Setting the Reception Mode
The machine has two modes for receiving incoming faxes: FAX mode: Select this mode when you only want to receive faxes on your line. The fax machine will automatically answer all calls on four rings and receive incoming faxes. TEL mode: Select this mode when you want to receive both phone calls and faxes on the line connected to the fax machine. All calls, including faxes, must be answered by picking up the fax machine's handset or an extension phone connected to the same line.
Setting the reception mode
Make sure a document is not loaded in the document feeder, and then press
until the arrow in the display points to the desired mode.

TEL FAX

JAN-03 10:30
For more information on receiving faxes in FAX and TEL modes, see Chapter 3, Receiving Faxes.

Volume Adjustment

You can adjust the volume of the speaker, handset, and ringer using the up and down arrow keys.

Speaker

Press or to select the desired volume level.

SPEAKER: HIGH

Press
again to turn off the speaker.

SPEAKER: MIDDLE

SPEAKER: LOW
When talking through the handset, press or to select the desired volume level.

RECEIVER: HIGH

Note: The volume reverts to MIDDLE
each time you replace the handset.

RECEIVER: MIDDLE

RECEIVER: LOW

Ringer

Press or to select the desired volume level. (Make sure has not been pressed, the handset is not lifted, and a document is not loaded in the feeder.)

Batch Page Numbering

You can change the page numbering of the transmitted document from simple numbering ("P.01", "P.02", etc.) to batch numbering, which means that a slash and the total number of pages being sent are added after each page number (for example, "P. 01/05", "P.02/05", etc.). This allows the recipient to check for missing pages.

PAGE COUNTER

ENTER # (01 - 99)
Enter the total number of pages (01 to 99) by pressing the numeric keys. Example: 5 pages

If desired, press

to set the resolution and/or contrast.
Dial the receiving machine and send the fax.
If you need to cancel a batch number entry, remove the document from the

feeder or press.

If the number of pages actually transmitted does not coincide with the batch
number entered, the alarm will sound and PAGE COUNT ERROR will appear in the display. PAGE E. will also appear in the NOTE column of the Transaction Report if printed.
Sending a Fax From Memory
You can scan a document into the machines memory and send the document from memory. This increases transmission speed and allows you to send a fax to multiple destinations in a single operation. After transmission, the document is automatically cleared from memory. Note: If a power failure occurs while sending a fax from memory, you will need to repeat the operation.
Broadcasting (sending a fax to multiple destinations)
This function allows you to send the same fax to as many as 20 different destinations in just one operation.
When sending to multiple destinations, only auto-dial numbers can be used
to dial the numbers of the receiving machines.
until the name of the destination appears in the display
(if no name was stored, the number will appear).
to store the destination.
Repeat Steps 3 and 4 for each of the other destinations to which you wish to send the fax (maximum of 20).
To check your selected destinations, press
to scroll through them. To.
delete a destination, scroll to the destination and then press
When you are ready to begin transmission, press
A Transaction Report is automatically printed out after Broadcasting is
completed. Check the "Note" column of the report to see if any of the destinations are marked "Busy" or have a communication error code. If so, send the document to those destinations again.

Memory transmission

You can also send a fax through memory when sending to a single destination. This is convenient when sending to destinations where the line is often busy, as it saves you from waiting to pick up the original document and frees the feeder for other operations. To send a fax through memory, load the document, press dial using one of the following methods:

When the machine rings, pick up the handset.
If you hear a fax tone, wait until the display shows RECEIVING and then replace the handset.

RECEIVING

If RECEIVING does not appear (or if you have set the Fax Signal Receive setting to NO), press

to begin reception.

If the other party first speaks with you and then wants to send a fax, press
after speaking. (Press before
the sender presses their Start key.)
When RECEIVING appears in the

display, hang up.

Answering on an extension phone connected to the same line
Answer the extension phone when it rings.
If you hear a soft fax tone, wait until your machine responds (you will hear pronounced, high-pitched tones), then hang up.
Pronounced, highpitched tones
If the machine doesn't respond, or if the other party first talks to you and then wants to send a fax, set the phone down (do not hang up), walk over to the machine, lift the machines handset, and press
The above step is necessary if you have set the Fax Signal Receive setting

to NO.

Putting a call on hold
To put the other party on hold during a phone conversation, press. When
this is done, they cannot hear you. You can put the handset back in the cradle without breaking the connection. When you are ready to speak with the other party again, pick up the handset. If you did not put the handset back in the cradle, press again to resume conversation.
Optional Reception Settings

Fax Signal Receive

The machine will automatically begin reception if you hear a soft fax tone after answering a call on the machine or an extension phone. If you use a computer fax modem to send documents on the same line, you must turn this function off in order to prevent the machine from mistakenly attempting to receive documents from the computer fax modem. Follow the steps below to change the setting.

5 times.

FAX SIGNAL RX
to turn on the function, or

CALLER-ID

Reception Ratio
The machine has been set at the factory to automatically reduce the size of received documents to fit the size of the printing paper. This ensures that data on the edges of the document are not cut off. If desired, you can turn this function off and have received documents printed at full size.
If a document is too long to fit on the printing paper, the remainder will be
printed on a second page. In this case, the cut-off point may occur in the middle of a line.
Automatic reduction may not be possible if the received document is too
large, contains too many fine graphics or images, or is sent at high resolution. In this case, the remainder of the document will be printed on a second page.

Note: This function cannot be used if you are using the Distinctive Ring function.
Distinctive Ring (Requires Subscription to Service)

Important:

To use distinctive ring, you must subscribe to a distinctive ring
service from your local phone company.
Note that your fax machine may not be compatible with some distinctive
ring services. Distinctive ring is a service offered by some local telephone companies whereby they assign an additional second number to your regular single line. The second number rings differently from your normal number. If you subscribe to a distinctive ring service, you can set the fax machine to automatically answer when your second number is called. This allows you to use the second number as an exclusive fax number. To have your fax automatically answer when your second number is called, follow the steps below:
Press a number from 1 to 3 (1 to 5 in Canada) to select the ring pattern below that matches your second numbers ring pattern. Press 6 to have your fax automatically answer your normal telephone number. Press 7 to turn off the distinctive ring function. RING PATTERN 1 RING PATTERN 2 RING PATTERN 3 RING PATTERN 4 (Canada only) RING PATTERN 5 (Canada only) STANDARD RING OFF SETTING Two short rings One short, one long, and one short ring Two short rings and one long ring Three very short rings Two very short rings Your standard (normal) ring pattern Turn distinctive ring off
Set the reception mode to FAX.
When using distinctive ring, you must set the reception mode of your fax
machine to FAX. When your designated fax number is dialed, your fax will automatically answer and begin reception after two rings. Note that other devices on the same line will also ring until your fax answers. If one of your other numbers is dialed, the fax will ring; however, it will not answer.
Blocking Reception of Unwanted Faxes
The Anti Junk Fax function allows you to block reception of faxes from a party that you specify. This saves paper by not printing out unwanted "junk" faxes. To use this function, follow the steps below to enter the fax number from which you do not wish to receive faxes. One fax number can be entered.
Press to store an Anti Junk number, or to clear a previously stored number (if you are clearing a number, go to Step 6). Enter the fax number by pressing the number keys (max. 20 digits).

If you find it difficult to remove dirt from the roller, moisten the cloth with
water and then wring it out thoroughly before wiping. Do not use alcohol, benzene, thinner, or other solvents. Wipe here

Cleaning the housing

Wipe the external parts and surface of the machine with a dry cloth. Caution! Do not use benzene or thinner. These solvents may damage or discolor the machine.

Improving Print Quality

Aligning the print cartridge
If print quality is not satisfactory, first try aligning the print cartridge.
Note: Make sure that paper is loaded before beginning this procedure.
After printing the alignment page the display shows:

CLEAN NOZZLES

Cleaning the print cartridge nozzles
If print quality is still not satisfactory after aligning the print cartridge, follow these steps to clean the print cartridge nozzles.
The machine prints a test pattern similar to the one shown in the following
Compare the diagonal line above the printed bars to the diagonal line below the printed bars.
Look for a break in the diagonal line above the bars. A break indicates

clogged nozzles.

Breaks in the diagonal line at the top of the page indicate clogged nozzles.
Unbroken lines at the bottom of the page indicate the nozzles were cleaned.
If the bottom diagonal line still has breaks, repeat Steps 1 through 4 to run the nozzle test again. Run the test a third time if necessary.
If the print quality is satisfactory after running the nozzle test three times,

the nozzles are clean.

If the print quality is still not satisfactory after running the test a third time,

continue with Step 7.

, open the operation panel, open the print compartment cover,
and remove and then reinstall the print cartridge (see the procedure beginning on page 16).
Repeat the nozzle test. If the lines are still broken, wipe the nozzles as explained in the following section.
Wiping the print nozzles and contacts
If you have cleaned the print nozzles as explained in the previous section at least three times and print quality is still not satisfactory, try wiping the print nozzles and contacts.
and remove the print cartridge (see the procedure beginning on page 16).
CAUTION! DO NOT touch the gold contact area of the cartridge or the

Dialing and transmission problems
Problem No dial tone when you pick up the handset or press the SPEAKER key.
Reception and copying problems
Problem The fax machine doesn't receive documents automatically. Solution Make sure that the reception mode is set to FAX. If you subscribe to a distinctive ring service, make sure that the Distinctive Ring function is set to the correct ring pattern. If you do not subscribe to a distinctive ring service, make sure that Distinctive Ring is set to OFF SETTING. (See Distinctive Ring on page 66.) Make sure that the document is loaded properly in the feeder of the transmitting machine. Make a copy or print a report to confirm the printing ability of your machine. The print cartridge may need alignment or cleaning. See page 77. Ask the other party to send higher contrast documents. The print cartridge may need replacement. Make a copy or print a report to check your machines printing ability. Received images are distorted. Noise on the telephone line may cause distortion. Have the other party try sending the document again. Make a copy or print a report on your fax machine. If the copy or report is also distorted, your fax machine may need service. The quality of copies is poor and/or dark vertical lines appear. Any dirt or material on the scanning glass will cause spots to appear on copies and transmitted faxes. Clean the scanning glass as explained on page 74.
The printing paper comes out blank when you try to receive a document.

Print quality is poor.

The received document is faint.
Solution Make sure the power cord is properly plugged into a power outlet. Connect another electrical appliance to the outlet to see if it has power. The machine does not respond when you press any of its keys. Automatic document feeding does not work for transmission or copying. If a beep sound is not made when you press the keys, unplug the power cord and then plug it in again several seconds later. Check the size and weight of the document (see Transmittable Documents on page 33).

General problems

Problem Nothing appears in the display.

Messages and Signals

Note: If you have turned on the Caller ID function, see page 62 for display messages related to Caller ID. ADD PAPER & / PRESS START KEY (alternating messages) Check the printing paper. If the tray is empty, add paper and then press

. If there is paper in the
tray, make sure it is inserted correctly (take out the stack, align the edges evenly, and then reinsert it in the tray) and then press CHANGE CARTRIDGE
This message appears after you install or replace the print cartridge (see page 18). The print cartridge is missing and must be installed, or is not installed correctly. The original document is jammed. See the following section, Clearing Paper Jams. Document jams will occur if you load more than 10 pages at once or load documents that are too thick (see page 33). The document may also jam if the receiving machine doesnt respond properly when you attempt to send a fax. A fax has been received in memory because the print cartridge needs replacement, you have run out of printing paper, or the paper is jammed. The fax will print out automatically when the problem is fixed. has been pressed. The cartridge is nearly empty (approximately one eighth of the ink remains).

CHECK CARTRIDGE

DOCUMENT JAMMED

FAX RX IN MEMORY

FUNCTION MODE

INK NEAR EMPTY

LINE ERROR
Transmission or reception was not successful. Press to clear the message and then try again. If the error persists, see Line error on page 82.

LOW INK

The cartridge is low on ink (approximately one quarter of the ink remains). If faxes have been received to memory because printing is not possible (an additional message will indicate the problem), resolve the problem so that printing can continue (see Substitute Reception to Memory on page 57). If you are attempting to transmit from memory, see If the memory becomes full on page 50. If you are copying, see If MEMORY IS FULL appears on page 59. The machine is preparing to or printing out a document from memory. This appears if you attempt to search for an auto-dial number when none have been stored. This appears if you forgot to replace the handset after using it to dial and send a fax. Replace the handset or press to clear the message.

MEMORY IS FULL

MEMORY PRINTING

NO # STORED

OFF HOOK

ON HOOK DIAL

has been pressed and the fax machine is waiting for you to dial.

OUT OF INK

The cartridge is out of ink and must be replaced. Faxes will be received to memory. The printing paper is jammed. See page 90. A printer error has occurred. Open the printer compartment cover, make sure the print cartridge is installed correctly, and then close the cover. Press to clear the message.

Remain on the line and briefly explain to the dispatcher the reason for the call. Perform such activities in the off-peak hours, such as early morning or late evening.

S H A R P

Revised date:. Issued date :Sep.19.2002
MATERIAL SAFETY DATA SHEET (1/3)

MSDS No. B-1028

Section 1. Product Identification
Product Code : Ink-Cartridge (Mono) UX-C70B
Section 2. Suppliers Name and Address
Sharp Corporation 22-22 Nagaike-cho, Abeno-ku, Osaka, Japan Local suppliers are listed below. Please contact the nearest supplier for additional information. (Country) U.S.A. (Name and Telephone Number) Sharp Electronics Corporation Telephone number for information: 1-800-237-4277 Emergency telephone number : 1-800-255-3924 Sharp Electronics of Canada Ltd. Telephone number for information : 905-890-2100 Emergency telephone number : 1-800-424-9300

Canada

Section 3. Composition / Information for Ingredients
Ingredients Carbon Black Acrylic Terpolymer Water Soluble Organic Solvents Hydroxylated Alkane Acrylic Resin Water Notes: Cas No. 1333-86-4 (2) (2) (2)(4) (2) 7732-18-5 Proportion (% by Weight) 1-6 0.1-2 10-20 1-10 0.1-5 >55 OSHA PEL 3.5 mg/m3 (1) (3) (3) (3) (3) (3) ACGIH TLV 3.5 mg/m3 (1) (3) (3) (3) (3) (3)
(1) Total dust (measured carbon black) (2) Trade secret of patented molecule. (3) Specific workplace exposure limits have not been established. (4) New Jersey Trade Secret Registration Number (NJTSRN) 80100451-5004
Section 4. Hazardous Identification
The following information is based on testing of the ink and on the characteristics of component chemicals: Primary Routes of Entry: Ink stains on skin or mucus membranes (mouth, eyes & nose) may cause discomfort. Medical Conditions Aggravated by Exposure: None known at intended levels of use. POTENTIAL HEALTH EFFECTS: Inhalation: Short Term Exposure -- If ink mist is inhaled, respiratory tract irritation may occur. Long Term Exposure -- No adverse chronic effects expected. Skin Contact: Short Term Exposure -- Ink may be slightly irritating to the skin. Long Term Exposure -- No adverse chronic effects expected. Not a dermal sensitizer. Short Term Exposure -- Not an eye irritant. Eye Contact: Long Term Exposure -- No adverse chronic effects expected. Ingestion: Short Term Exposure -- Low oral toxicity. Long Term Exposure -- No adverse chronic effects known or expected, but based on component characteristics, gastrointestinal effects, liver and kidney toxicity, and CNS effects are possible if large quantities of ink are repeatedly ingested.

Section 12. Toxicological Information
Acute Toxicity: Chronic Toxicity: Not expected to be acutely toxic; LD50 (oral, rat) expected to be >2000 mg/kg. Not expected to be chronically toxic based on component information, volume, concentration, and intended use. Pure carbon black, a minor component of this ink, has been listed by LARC as group 2B (possible carcinogen). This classification is based on rat lung particulate overload studies performed with airborne particulate carbon black.Ink is not listed by LARC, NTP, or OSHA. OSHA Regulated(USA): Not listed In 1996 the LARC reevaluated carbon black as a Group 2B carcinogen (possible human carcinogen). This evaluation is given to Carbon Black for which there is inadequate human evidence, but sufficient animal evidence. The latter is based upon the development of lung tumors in rats receiving chronic inhalation exposures to free carbon black at levels that induce particle overload of the lung. Studies performed in animal models other than rats have not demonstrated an association between carbon black and lung tumors.

Carcinogenicity:

Section 13. Ecological Information

No data available.

Section 14. Disposal Consideration
This product is not a listed or hazardous waste in accordance with Federal Regulation 40 CFR Part 261. If discarded, this product would not be a hazardous waste either by listing or by characteristic. However, it is the responsibility of the product user to determine at the time of disposal whether a material has been contaminated and should be classified as a hazardous waste. In accordance with RCRA 40 CFR Section 264.314 and 265.314, the placement of any liquid in landfills is prohibited. Disposal is subject to local, state and federal regulations.
Section 15. Transport Information
DOT PROPER SHIPPING NAME: Not regulated as hazardous material.
Section 16. Regulatory Information
All ingredients are registered under the Toxic Substances Control Act (TSCA) or underpolymer exemption. All ingredients are exempt, registered or considered registered (polymers) under the European Inventory of Existing Commercial Chemical Substances(EINECS/ELINCS). Preparation not classified as dangerous (EU Directive 67/548/EEC;1999/45/EC). All ingredients are listed on or are considered polymers under the Canadian Domestic Substances List (DSL) or Non Domestic Substances List (NDSL). Note of the product ingredients are listed as Emergency Planning and Community Right-to-Know Act (EPCRA)-Section 302: Extremely Hazardous Substances (EHS). None of the product components are present above the minimum quantities of listed chemicals in EPCRA Section 313 Supplier Notification. This product contains no known materials at levels which the State California has found to cause cancer, birth defects or other reproductive harm - California Proposition 65.

Section 17. Other Information
Restrictions: This information relates only to the specific material designated as supplied by the manufacturer. This information is supplied to us by the manufacturer and Sharp offers no warranties as to its accuracy and accepts no responsibilities for any typographical errors which may appear on these sheets. It is the responsibility of the user to determine the suitability of this product for each particular use. Literature Reference: LARC(1996): LARC monographs on the Evaluation of the Carcinogenic Risk of Chemicals to Humans, Vol.65, Printing Process and Printing Inks, Carbon Black and Some Nitro Compounds, Lyon, pp.149-261 H.Muhle, B.Bellmann, O.Creutzenberg, C.Dasenbrock, H.Ernst, R.Kilpper, J.C.MacKenzie, P.Morrow, U.Mohr, S.Takenaka, and R.Mermelstein(1991) Pulmonary Response to Toner upon Chronic Inhalation Exposure in Rats. Fundamental and Applied Toxicology 17, pp.280-299

Quick Reference Guide

Sending Faxes
Place your document (up to 10 pages) face down in the document feeder. Normal Dialing

Receiving Faxes

until the arrow in the display
points to the desired reception mode.
1. Lift the handset or press 2. Dial the fax number.
FAX mode: The fax machine automatically answers and receives faxes. TEL mode: Answer all calls (even faxes) by picking up the handset. To begin fax reception, press
3. Wait for the reception tone (if a person answers, ask them to press their Start key). 4. Press
Storing Auto Dial Numbers
Automatic Dialing 1. Press 1. Press or until the desired 2. Enter the fax number. 3. Press
destination appears in the display. 2. Press
4. Enter a name by pressing number keys. Direct Keypad Dialing 1. Dial the fax number. 2. Press
(To enter two letters in succession that require the same key, press entering the first letter.) after
SPACE = A= B= C= D= E= F= G= H= I = J= K= L= M= N= O= P= Q= R= S= T= U= V= W= X= Y= Z=

5. Press

and then

Gua de referencia rpida

Transmisin de documentos
Coloque el documento (hasta 10 pginas) mirando hacia abajo en el alimentador. Marcacin normal 1. Levante el auricular o pulse 2. Marque el nmero de fax. 3. Espere a escuchar el tono de recepcin (si alguien contesta al telfono, pdale que pulse la tecla Inicio). 4. Pulse

Recepcin de documentos

hasta que la flecha de la
pantalla seale el modo de recepcin deseado. RESOLUTION/

RECEPTION

Modo FAX: El aparato de fax contestar y recibir documentos automticamente. Modo TEL: Contesta todas las llamadas (incluso las de fax) levantando el auricular. Para que comience la recepcin del documento, pulse

School/Organization Name________________________________________ Contact Name _______________________________ Address ___________________________________________ City ________________________ State _________ Zip ________ E-Mail ______________________________ Phone _______________________ Fax ___________________ Date ___________ Please fill out this form and fax it back to us or simply enclose it with your shipment. If this form is faxed prior to your shipment being sent we will send you pre-paid labels for returning your cartridges. Minimum of 30 inkjets or more per box. Please note: If Empty Cartridge Inventory Sheets are not filled out we will take an inventory on your empties and send you a check.

Dazz Cycle

Empty Inkjet Inventory List

1-866-543-9465

Fax 1-866-454-5439
- INKJET CARTRIDGE LIST Canon Ink-Jet Cartridges
BJ-200/BJ-100 (BC-02) BJC-210/240 (BC-05) BJ-200/300 (BX-3) PIXMA Series (PG-30/CL-31) PIXMA Series Black (PG-40/PG-50) PIXMA Series Color (CL-41/CL-51) PIXMA Series Black (PGI-5) #5 (PGI-7) #7
PIXMA Series All Colors (CLI-8) #8 (CLI-9) #9

$ Value

PIXMA Series Blk (PGI-220) Clr (CLI-221)
PIXMA Series Blk (PGI-225) Clr (CLI-226) PIXMA Series Blk (PG-210XL) Clr (CL-211XL)
PIXMA Series Blk (PG-210) Clr (CL-211)
$ 0.50 $ 0.50 $ 1.00 $ 0.25 $ 1.00 $ 3.00 $ 0.10 $ 0.10 $ 0.25 $ 0.25 $ 1.50 $ 1.00 $ 0.05 $ 0.25 $ 0.50 $ 0.50 $ 0.50 $ 3.00 $ 0.50 $ 0.25 $ 0.50 $ 3.50 $ 0.10 $ 0.25 $ 0.10 $ 1.00 $ 0.50 $ 2.50 $ 0.10 $ 1.00 $ 2.50 $ 0.25 $ 1.00 $ 0.50 $ 1.00 $ 1.50 $ 0.05 $ 0.10 $ 0.50 $ 0.25 $ 0.10 $ 0.50 $ 0.25 $ 0.50 $ 1.50 $ 2.50 $ 0.10 $ 0.50
Lexmark Ink-Jet Cartridges Z735 (18C0781) # 1 Z2320 (18C0190) #2 / #3 / #4A / #5A Z2320 (18C2090) #14 / #15 Z23/Z25/Z33 (10N0016) #16 Z23/Z25/Z33 (10N0017) #17 Z51 (15M0120/15M0125) #20 / #25 X4530 (18C1523/24) #23 / #24 Z23/Z25/Z33 (10N0026) #26 Z23/Z25/Z33 (10N0027) #27 X2500/Z845 (18C1248/29) #28 / #29 5250/5270/Z816 (18C0032) #32 / #33 5250/5270/Z816 (18C0034) #34 / #35
Z2420 (18C2130) #36 / #36XL / #37 / #37XL

HP Ink-Jet Cartridges

#02 / #10 / #11 / #14 / #88 / #940 All Clrs 810C/812C (C6615AN/DN) #15 840C/842C (C6625AN) #17 610C/612C (C6614AN/DN) #20 3910/3940 (C9351AN) #21 / #21XL 3910/3940 (C9352AN) #22 / #22XL 720/800 (C1823A/D/G) #23 FAX 200/300 (51626A/G) #26 3320/3325/3425 (C8727A) #27 3320/3325/3425 (C8728A) #Series (51629A/G) #29 700/800 (51645A/G) #Series (51649A) #49 3910/3940/1410 CB334AN #54 5150/5550/7150 (C6656A) #56 5150/5550/7150 (C6657A) #57 5150/5550/7150 (C6658A) #58
D2560 (CC640WN) #60 / #61 Blk and Clr D2560 (CC641WN) #60XL / #61XL Blk and Clr
X9350 #40 / #41 / #42 / #43 / #44 / #43XL / # 44XL Z12/Z32 (17G0050) #48 / #50 / #55 Z12/Z32 (17G0060/65) #60 / #65 5700/7000 #70 / #71 / #(12A1980/85/90) #80 / #85 Z55/Z65 (18L0032/42) #82 / #83 / #88 805/905 #100 / #105 / #105XL
$ 1.00 $ 1.00 $ 0.10 $ 1.00 $ 1.00 $ 0.25 $ 0.10 $ 0.50 $ 0.50 $ 0.10 $ 0.25 $ 2.00 $ 0.10 $ 0.10 $ 0.50 $ 0.25 $ 0.50 $ 0.25 $ 0.25 $ 0.10 $ 1.00 $ 0.50 $ 0.25 $ 0.25 $ 0.25 $ 0.25 $ 0.25 $ 0.25 $ 0.25 $ 0.25 $ 0.25 $ 0.25 $ 0.25 $ 0.10 $ 0.10 $ 0.10 $ 0.10 $ 1.00 $ 0.05 $ 0.05 $ 0.50 $ 0.05 $ 2.00

Dell Ink-Jet Cartridges

Series 1 A920 #T0529 Series 1 A920 #T0530 Series 2 A940/960 #7Y743 Series 2 A940/960 #7Y745 Series 5 A922 #J5566 Series 5 A922 #J5567 Series 5 A922 #M4640 Series 5 A922 #M4646 Series 6 810/725 #JF333
Series #DH828 / #DH829 / #CH883 / #CH884

Series #MJ264

Series #MK990 / #MK991 / #MK992 / #MK993 Series #KX701 / #KX703 / #JP451 / #JP452
J5730/J5750 (CB335WN) #74 J5730/J5750 (CB336WN) #74XL J5730/J5750 (CB337WN) #75 J5730/J5750 (CB338WN) #75XL 900 Series (C6578A/D) #78 / #78XL OfficeJet Pro K550 #88 All Colors 5440/7850/1510 (C9362WN) #92 5440/7850/1510 (C9361WN) #93 5740/6540 (C8765WN) #95 5740/6540 #94 / #96 / #97 / #98 / #99 A432/516 (CB304A) #110 #701
P7500 (CB322WN) #564 and #920 All Clrs P7500 (CB322WN) #564XL and #920XL
Series 15 V105 #U143F / #U145F Series 21 V313 #Y498D / #Y499D Series 22 and 23 V515 #X737N / #X752N Series 24 V715 #X768N / #X771N Sharp UX-70 Black All Skinny Epsons Brother LC-51 All Colors Brother LC-61/LC-65 All Colors
All Other Inks (Not refilled Epson, Bro, or Canon)
Cell Phone w/ Camera (Not Broken / Must be Functional)
Miscellaneous Ink-Jet Cartridges and Cell Phones
J4580 (CC653AN) #901 Blk and Clr J4580 (CC653AN) #901XL Blk #21 / #27 / #56 Prev. Refilled #22 / #28 / #57 Prev. Refilled
Total Quantity of InkJet Cartridges: Grand Total for InkJet Cartridges : $
Prices Effective 03/20/2011 Prices Subject to change Always Check our website for current pricing @ www.dazz-cycle.com