PREPAREDBY :

LCY-99160A

APPROVEDBY :

DATE TFT LIQUID CRYSTALDISPLAY GROUP SHARPCORPORAT I ON
ISSUE : LIAR. 31. PAGE: 20 pages APPLI CABLE GROUP TFT LIQUID CRYSTAL DISPLAY GROUP

SPECIFICATION

DEVICE SPECIFICATION FOR

TFT-LCD

MODEL No.

LQ039QZDS53

CUSTOMER'SAPPROVAL
PRESENTED BY S. YASUDA DIVISION DEPUTYGENERAL MANAGER DEVELOPMENT ENGINEERING DEPT. II TFJ DJVISION I TFT LIQUID CRYSTALDISPLAY GROUP SHARPCORPORATION 1

sHARf=

MODEL SPEC No I 1999.10. 27

RECORDS REV1 OF SION

No:LQ039QZDS53 :LCY-99160 un

PIIWARV YllYlU\.

NflTc.-.&A

LCY-99160

Lampcurrent : ________.___________---------------------------------------.

1 st Issue Added

LCY-99160A 7 Table 1-2 : 2000.03.31 ____________._______------------.--------------------------------------------------.

----_---_--_._--____----

1.5 h1h11s1 MAX 5. 5 hArms~ ,
________________-__------. ----_--. _____-.
____________._i_____------------.--------------------------------------------------. _-_________-.__-_---------------.------------------------___--_______.______-------------.------------------------------------------____________._____-_____________._____._-------------------------------------, ____________._______------------.--------------------------------------------------. ________________________________________------------.------_-----_------____ _-_-_______-______ _____________________________ ____________~______-------------.--------------------------------------------------. ____________._______------------.--------------------------------------------------. ____________________------------.--------------------------------------------------. ___-________.___________________.___________________-------------------------------. ____________._______------------.--------------------------------------------------. ____________._______------------.--------------------------------------------------. _-__________._______------------.------------------------------------------_-__-__--___~_____________ ______._____________-----------------------------____________._______------------.-----.--------------------------------------------. ___________.___________________._-_________________-------------------------------__-_-_-____.________-----------.----____________-________ _______-________-___----em---------__________________-_-----------_______.___________________._-_--_------e-_--u ----em-.
__________________ _____________________________ _________________.__---------~--~----~--------~----------.-_---.__-----.--
_---___-_______________________ _________________-__-------------------------------___________.________-----------.--------------------------------------------------____-______.____________________________------------------------------------------___________,________-----------.-----.--------------------------------------------_______-___.________-----------.-----~--------------------------------------------__--_______.________-----------.--------------------------------------------------___________.___________________.___________________-------------------------------___________,____________________________------------------------------------------___________~___________________ _________-_______________--------------------------

LCY-99160A NOTICE

This publication
is the proprietary of SHARP and is copyrighted with all rights reserved.
Under the copyright laws, no part of this
Publication may be reproduced or transmitted in any form or by any means, electronic or mechanical for any purpose, in whole or in Piart, without the express written permission of SHARP. Express written permission is also required before any use of this Publication may be made by a third party. The application circuit examples in this publication are provided to explain the representative applications of SHARPs devices and SHARI takes
ate not intended to guarantee any circuit design or permit any industrial property right or other rights to be executed.
ncJ responsibility for any problems related to any industrial property right or a third party resulting from the use of SHARPs devices, errcepf for those resulting directly from device manufacturing processes. In the absence of confirmation by device specification lecification sheets before using any SHARPs device. SHARP reserves the right to make changes in the specifications, characteristics, data, materials, structures and other conten scribed herein at any time without notice in order to improve design or reliability. Contact SHARP in order to obtain the late ecification sheets before using any SHARPs device. Manufacturing locations are also subject to change without notice. Observe the following points when using any device in this publication. Iproper use of the devices. SHARP takes no responsibility for damage caused t sheets, SHARP takes no responsibility for any defects that

luipment using any of SHARPs devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest devil
The devices in this publication are designed for use in general electronic equipment designs, such as: Personal computers / Office automation /Telecommunication Consumer electronics The appropriate design measures should be taken to ensure reliability and safety when SHARPs evices are used for equipment such as: Transportation control and safety equipment(i.e., aircraft, trains, automobiles, etc.) I?affic signal ! Gas leakage sensor breakers Alarm equipment / Various safety devices etc. SHARPs devices shall not be used for equipment that requires extremely high level of reliability, Ich as: Military and space applications / Nuclear power control equipment Medical equipment for life support Contact a SHARP representative in advance, when intending to use SHARF? devices for any specific applications ose recommended by SHARP. Contact and consult with a SHARP representative, if there are any questions about the contents ofthis publication. other tha I equipment Test and measurement equipment / Industrial control / Audio visual and multimedia equipment
(1) Application This specification applies to color TFT-LCD module, LQO39Q2DS53.

(2) Overview

This module is a color reflective and active matrix LCD module incorporating amorphous silicon TFT (Thin Film panel. driver KS, an FPC, a front Transistor), named HR-TFT (High Reflective TFT). It is composed of a color TFT-LCD
light, a touch panel and a back sealed casing. It isnt composed control circuit. Graphics and texts can be displayed on 320 x 3 x 240 dots panel with 262,144 colors by supplying. Optimum view angle is 12 oclock. An inverted display mode is selective in the vertical or the horizontal direction. (3) Mechanical specifications
vote 3-l] Excluding protrusion. (4) Pixel configuration For detailed measurements and tolerances, please refer to Fig. I.

Display Area

(1.240)

( 320.240

(5) Input/Output terminal 5-l)TlT-LCD panel driving section

LCY-99 160A -3

LCY-99

I60A -4

INoteS-l]See section (7-1)-(A) *Cautions when you turn on or off the power supply. mote5-2lSelection for vertical scanning direction
Scanning direction (Pixel configuration) Normal scanning ( X , I) II ( x ,240 )

Inverted scanning

( X , 1) l? ( X ,240)
[NoteSJlSelection LBR High Low
for horizontal scanning direction SPL SPR Input output output Input
Scanning direction (Pixel configuration) Normal scanning Inverted scanning (1 ,Y) to (32O.Y) (1 ,Y) to (320,Y)
5-2) Front light driving section Table 5-2 Pin No. Ll L2 [NoteSAlL Symbol VLI vL2 I/O I I Description Power supply for fluorescent tube (High voltage) [Note541 Power supply for fluorescent tube (Low voltage) Remark
terminal should be connected to either GND voltage terminal ofDC/AC invertcr.
5-3) Touch panel driving section Pin No. Tl T2 T3 T4 Symbol Y! x2 Y2 x1 I/O Description

Remark

Lower electrode Y (12 oclock side) Upper electrode X (right side) Lower electrode Y (6 oclock side) Upper electrode X (let? side)
(6) Absolute Maximum Ratings Table 6

[Terminal

l] VO,Vl,V2,V3,V4,V5,V6,V7,V8,VY oftouch panel ( Xl, X2, Y I, Y2, ) are applied. 95%RH Max.(at Ta I 40C). Maximum wet-bulb temperature is less than 39C (at Ta>4OC).
[Terminal 21 MOD,Un,SPS,CLS,SPL,RO-RS,GO-GS,BO-BS,LP,DCLK,LBR,SPR,PS [Note6-l]Terminal vote6-Z]Humidity:
Condensation of dew must be avoided.
(7)Electrical characteristics
7-1) Recommended operating conditions
A) TFT-LCD paneldrivingsection
*Cautions when you turn on or off the power

supply

(a) Turn on or off the power supply with simultaneously or the following sequence. Turn on -- VSHD and VSHA first. then VCC. then VSS, then VEE *then VDD. Turn off --- VDD first, then VEE, then VSS, then VCC, then VSHD and VSHA (b) The input signal of MOD Terminal(Pin No.3) must be LOW level voltage when turning on the power supply, and it is held until more than double vertical periods after VCC is turned on completely. After then, give it HIGH level voltage until power off. vote 7-l]These are standard input voltages for gray scale. When VCOM is alternated polarity, these voltage should bc altcmated polarity. VO(black) is different polarity alternating signal of VCOM. V9(white) is the same polarity alternating signal of VCOM. Center voltage of each standard input voltage shift positive way for LCD characteristics (namely VO shifts positive first, then VI, then V2, then V3, then V4, then V5, then V6, then V7, then VS, and then V9). This sift amount is adjusted so as to no flicker of each standard input voltage after DC bias voltage of VCOM and VO is adjusted. mote 7-21 It must be kept that 3.OV 5 (VCC-VSS) < 3.6V. 0 must be held high voltage until turning off the power supply. (Connect Pin No.3 and No.4 terminals to the same signal.) [Note 7-3]The same phase and amplitude with VCOM. VEEDC is center of VEE. [Note 7-4]DCLK,SPL,SPR,LBR,LP,PS,RO-RS,GO-G5 [Note 7-S]DCLK,SPL,SPR,LBR,LP,RO-RS,GO-G5 mote 7-6]PS terminal is applied. and BO-B5 terminals are applied. and BO-B5 terminals are applied.

mote 7-7]MOD,CLS,SPS and U/L terminals are applied
[Note 7-BIVCOMAC should be alternated on VCOMDC every 1 horizontal period and 1 vertical period. VCOMDC is adjusted so as to minimize flicker or maximum contrast every each module. B) Front light driving section

wore 7-9]Calculated

reference value(IL x VL)
7-2) Timing Characteristics of input signals

[Note I-IO]There

must be only one up-edge of DCLK (includes Tsusp and Thsp time) in the period of SPL(or SPR)=Hi.

LCY-99160A-8

SPL,SPR

RO-R5 Go-G5 BON-B5

SPL,SPR fm

Table 7-4

Setup Hold
AC Characteristics (2) Symbol Tsulpck Thlpck Twlp Mm. 20 Typ. Max. Unit Remark time (CK)

Parameter

time (CK)
Source LP , High level width
Thlpck < Thlpck < LP Lisp Thv Twlp > 1 A

< I

Tsulpck h-4
7-3) Power consumption Measurement condition : SPS=~OH~,CLS=~~.~~~HZ,SPL(SPR)=I~.~~~H~,DCLK=~.~MHZ The term of PS=Lo in one horizontal period -- 44psec(280DCLK) Ta=25C when normal scan mode

[Note 7-1 l]Vertical

stripe patternalternating gray scale (GS21) with 42 gray scale (GS42) every 1 dot. 21 vertical pattern (GSO - GS63 for horizontal way)

mote 7- 12]64-Gray-bar

8.lnput Signals, Basic Display Color and Gray Scale of Each Color

Table 8

Darker irighter a Bfeu

GSI GS+ GS61 GS62 GS63

0 : Low level voltage

1 : High level voltage

Each basic color can be displayed in 64 gray scales from 6 bit data signals. According to the combination of total 18 bit data signals, the 262,144-color display can be achieved on the screen.
(9)Optical characteristics 9-J)Not driving the front light condition

Ta=25"C

160A - 11

Response time

Rise Fall

e =O" (0.26) (0.31)

9-3,4]

(0.30) (0.34)

(0.33) (0.39)
White chromaticity Reflection ratio

vote 9-S] % [Note 9-3.61

+ The measuring method of the optical characteristics is shown by the following figure. * A measurement device is Otsuka luminance meter LCDSOOO.(With the diffusion reflection unit.)

Norm hobe Ial

Chemical coated surface (Optical diffusion treatment) J i Ir
Photodetector (with luminosity correction system)
A beam (through an optical fiber) dL)

Touch panel Module

Center of display
Measuring method (a) for optical characteristics
Measuring method (b) for optical characteristics
9-2)Driving the front light condition

f-j=00

(0.26) (0.28)

50 (0.28) (0.31) 40 -

100 (0.33) (0.39) -
White chromatic@ Brightness Lamp life time

Y Y LL

0 = 0 IL=5.OlllA IL=S.OmA

25 10000

(c&m3 hour mote 9-71
+ The measuring method of the optical characteristics is shown by the following figure. *A measurement device is TOPCON luminance meter BM-S(A).(Viewing Photodctector(including luminosity fatter) _. -.

cone1)

Center
Measuring method (c) For optical characteristics
[Note 9-l] Viewing angle range is defined as follows.

160A - 14

6oWock direction

Definition mote 9-21

for viewing angle
Definition of contrast ratio: The contrast ratio is defined as follows: Photodetecter output with all pixels white(GS63) Photodetezter output with all pixels blaclc(GS0)
~COMAC=~.~~p-p,~o-~.~~p-p,~~=-4.~~~~

Contrast ratio(CR)=

[Note 9-31 These values are under the condition of measuring method (b) with a point light source (lighting angle=30). [Note 9-41 Definition of response time: The response time is defined as the following the input signal for black and white. figure and &all be measured by switching
mote 9-51 A measurement device is Minolta CM-2002. [Note 9-61 Definition of reflection ratio Reflection ratio = Light detected level of the reflection by the LCD module Light detected level of the reflection by the standard white board

LCY-9916OA

[Note 9-71 The lamp life time is defined as a time when brightness not to become under 50% of the original value. mote 9-81 These values are under the condition of measuring method(a) with a diffusion light source. (1O)Touch panel characteristics
Insuration resistance Minimum (11) Display quality tension for detecting

] atDC25V

The display quality of the color TFT-LCD for TFT-LCD. (12) Mechanical characteristics 12- 1) External appearance See Fig. 1 12-2) FPC (for LCD panel) characteristics (a) Specific connector FH 12-50S-OSSH (HIROSE)
module shall be in compliance with the Incoming Inspection Standards
(c) Bending endurance of the bending slits portion(See Fig.1) No line of tbe FPC is broken for the bending test (Bending radius =OAmm and angle =90) in 30 cycles. ( 13)Handling Precautions 13-l) Insertion and taking out of FPC Be sure insert and take out of the FPC into the connector of the set after turning off the power supply on the set side. 13-2) Handling of FPC The FPC shall be bent only slit portion. The bending slit shall be bent uniformly on the whole slit portion with bending radius larger than 0.6mm ,and the direction is only inner side (back side of the module). Dont bend it outer side (display surface side). Dont give the FPC too much force, for example, hanging the module with holding FPC. 13-3) Handling of lead wire of CCFI (a) Dont pull GND line for CCFT in order to avoid the trouble on CCFT. (b) Handle with care not to scratch the lead wire of CCFT or FPC by the edge of metal case. 13-4) Installation of the module On mounting the module, be sure to fix the module on the same plane. Take care not to warp or twist the module.

13-5) Precaution when mounting (a) The polarizer can be easily scratched. Handle it with suflicient cart. (b) If water droplets and oil attaches to it for a long time, discoloration and staining occurs. Wipe them off

immediately.

(c) Glass is used for the TFT-LCD
panel and touch panel. If it is dropped or bumped against a hard object, it may
be broken. Handle it with sufftcient care. (d) As the CMOS IC is used in this module, pay attention to static electricity when handling it. Take a measure for grounding on the human body. 13-6) Others (a) The liquid-crystal is deteriorated by ultraviolet rays. Do not leave it in direct sunlight and strong ultraviolet rays for many hours. (b) If it is kept at a temperature below the rated storage temperature, it becomes coagulated and the panel may be broken. Also, if it is kept at a temperature above the rated storage temperature, it becomes isotropic liquid and does not return to its original state. Therefore, it is desirable to keep it at room temperature as much as possible. (c) If the LCD breaks, dont put internal liquid crystal into the mouth. When the liquid crystal sticks to the hands, feet and clothes, wash it out immediately. (d) Wipe off water droped or finger grease immediately. Long contact with water may cause discoloration (e) Observe general precautions for all electronic components. (f) VCOM must be adjusted on condition of your fmal product. No adjustment causes the deterioration quality. (g) Static image should not be displayed more than 5 minutes in order to prevent from occurrence of residual image. (I 4) Forwarding (a) (b) (c) (d) form MAX IPCS. 2500 g or spots. for display
Piling number of cartons:
Package quantity in one cartons:
Carton size: 420 mm(W) x 360 mm(D) x 120mm(H) Total mass of I carton filled with full modules:
Fig.2 shows packing form.
(15) Reliability Test Conditions for TFT-LCD Module

Shock test

980 m/s*, 61ns fx, *Y, +z 3 times for each direction (JIS COO4I, A-7 Condition C) Frequency range: 1OHz-55Hz Sweep: IOHz-55Hz Stroke: 1.5 mm X,Y,Z 2 hours for each direction (total 6 hours) (JIS C0040,A-10 Condition A) (Ih)

Vibration test

Heat shock test Point activation test (Touch panel) Writing friction resistance test (Touch panel)

Ta=-25C -+7OC I 5 cycles (lh) Hit it 1,OOO,OOO times with a silicon rubber of R8 HS 60. Hitting force : 250g Hitting speed : 3 times per second Write according to the right illustration mentioned Load : 250gf Speed : 3 strokes per second Stroke : 35mm Frequency : 50000 times x 4 pieces Testing apparatus : shown in Fig (I) conditions: Pen : 0.8R Polyacetal stylus in the under -

Weight

I 7u!m

Touch Panel Fig. 15

SHARI=
[Notc]Ta = Ambient temperature, Tp = Panel temperature [Check items]
(a) Test No. I-9 In the standard condition, there shall be no practical problems that may affect the display function. (b) Test No. I O-No. I I The measurements after the tests satisfy (IO) Table IO. (Touch panel characteristics) (16) Others 16- 1) Indication of serial number The serial number is shown on a label. Attached location is shown in Fig.1 (Outline Dimensions). Indicated contents of the label LQ039Q2DS53 model No. 00000000 serial No.
16-2) Used Regulation of Chemical Substances Breaking Ozone Stratum Substances with the object of regulating : CFCS, Carbon tetrachlotide, Halon I, 1, I-Trichloro (a) (b) This LCD module, Constructed manufacture. 16-3) If some problems arise about mentioned items in this document and other items, the user of the TFT-LCD and Sharp will cooperate and make efforts to solve the problems with mutual respect and good will. module ethane (Methyl chloroform) This LCD module, Constructed part and Parts dont contain the above substances. part and Parts dont contain the above substances in processes of
T. bend is FPC General Unit larger tolerance mm

than is

P. FPC CONNECTOR: 52207-0417 (JAPAN moiex)

RO.6 20.3

I c -------_I

Oatline

dimensions

7 z E z

LCY-99 160A -20

Master

carton

Caution i s

Maximum per

tinits carton

Packing