O P E R A T I N G I N S T R U C T I O N S

AM/FM STEREO RECEIVER

RX-4103

DISCRETE AMPLIFIER STAGE

VOLUME

MEMORY T/P MODE

REMOTE SENSOR

BALANCE

STANDBY

TUNING/PRESET

TV/AUX

TONE DIRECT

ON/STANDBY

PHONES

A SPEAKER B

Introduction

UNPACKING AND INSTALLATION
ENGLISH Congratulations on Your Purchase!
Your new high fidelity receiver is designed to deliver maximum enjoyment and years of trouble free service. Please take a few moments to read this manual thoroughly. It will explain the features and operation of your unit and help ensure a trouble free installation. Please unpack your unit carefully. We recommend that you save the carton and packing material. They will be helpful if you ever need to move your unit and may be required if you ever need to return it for service. Your unit is designed to be placed in a horizontal position and it is important to allow at least two inches of space behind your unit for adequate ventilation and cabling convenience. To avoid damage, never place the unit near radiators, in front of heating vents, in direct sunlight, or in excessively humid or dusty locations. Connect your complementary components as illustrated in the following section. FOR U.S.A. Note to CATV System Installer: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. FCC INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. CAUTION: Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Caution regarding placement (Except for U.S.A. and Canada) To maintain proper ventilation, be sure to leave a space around the unit (from the largest outer dimensions including projections) equal to, or greater than, shown below. Left and right panels: 5 cm Rear panel: 10 cm Top panel: 20 cm

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING

To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. Caution : Do not block ventilation openings or stack other equipment on the top.
READ THIS BEFORE OPERATING YOUR UNIT
FOR U.S.A. AND CANADA.. 120 V FOR OTHER COUNTRIES. 115 V/230 V
FOR YOUR SAFETY Units shipped to the U.S.A. and Canada are designed for operation on 120 V AC only. Safety precaution with use of a polarized AC plug. However, some products may be supplied with a nonpolarized plug. CAUTION : To prevent electric shock, match wide blade of plug to wide slot, fully insert. ATTENTION : Pour eviter les choc electriques, introduire la lame la plug large de la borne correspondante de la prise et poussre jusquau fond.

FOR YOUR SAFETY Units shipped to countries other than the above countries are equipped with an AC voltage selector switch on the rear panel. Refer to the following paragraph for the proper setting of this switch. AC VOLTAGE SELECTION This unit operates on 115/230 V AC. The AC voltage selector switch on the rear panel is set to the voltage that prevails in the area to which the unit is shipped. Before connecting the power cord to your AC outlet, make sure that the setting position of this switch matches your line voltage. If not, it must be set to your voltage in accordance with the following direction. AC voltage selector switch
FOR CHINA, EUROPE AND AUSTRALIA. 220V/230V/240V FOR YOUR SAFETY Units shipped to China are designed for operation on 220 V AC only. Units shipped to Australia are designed for operation on 240 V AC only. To ensure safe operation, the three-pin plug supplied must be inserted only into a standard three-pin power point which is effectively earthed through the normal household wiring. Extension cords used with the equipment must be three-core and be correctly wired to provide connection to earth. Improper extension cords are a major cause of fatalities. The fact that the equipment operates satisfactorily does not imply that the power point is earthed and that the installation is completely safe. For your safety, if in any doubt about the effective earthing of the power point, consult a qualified electrician. PAN-EUROPEAN UNIFIED VOLTAGE All units are suitable for use on supplies 230-240 V AC. AC 230 V AC 115 V
Move switch lever to match your line voltage with a small screwdriver or other pointed tool.

ENGLISH

CONTENTS
UNPACKING AND INSTALLATION... 2 READ THIS BEFORE OPERATING YOUR UNIT... 3
System Connections..... 5 Front Panel & Remote Controls..... 7
REMOTE CONTROL OPERATION RANGE... 9 LOADING BATTERIES..... 9

Operations

LISTENING TO A PROGRAM SOURCE.... 10 LISTENING TO RADIO BROADCASTS.... 12 RECORDING..... 14 OTHER FUNCTIONS.... 14
Troubleshooting Guide.... 15 Specifications..... 16

System Connections

Do not plug the AC input cord into the wall AC outlet until all connections are completed. Be sure to connect the white RCA pin cord to the L(left) and the red RCA pin cord to the R(right) jacks when making audio connections. Change the position of the FM indoor antenna until you get the best reception of your favorite FM stations. A 75 outdoor FM antenna may be used to further improve the reception. Disconnect the indoor antenna before replacing it with the outdoor one. Place the AM loop antenna as far as possible from the receiver, TV set, speaker cords and the AC input cord and set it to a direction for the best reception. If the reception is poor with the AM loop antenna, an AM outdoor antenna can be used in place of the AM loop antenna. Make connections firmly and correctly. If not, it can cause loss of sound, noise or damage to the receiver. If the electricity fails or the AC input cord is left unplugged for more than 2 weeks, the memorized contents will be cleared. Should this happen, memorize them again.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2)This device must accept any interference received, including interference that may cause undesired operation.

AC INPUT 120V~60Hz 2.5A

MODEL NO. RX-4103 STEREO RECEIVER
MADE IN CHINA DESIGNED IN USA

SPEAKERS

SER. NO

OUT IN

SPEAKER IMPEDANCE A, B - 8 MIN / SPEAKERS A+B -16 MIN / SPEAKERS

ANTENNA

I CONNECTING ANTENNAS

FM (OUTDOOR ANTENNA)

I CONNECTING AUDIO/VIDEO COMPONENTS

CD player

MULTIPLE COMPACT DISC PLAYER CDC-5080R

OPEN/CLOSE

V-CD PBC REVERT PROG PEAK DELETE AUTO EDIT

ON/OFF

GRAPHICS

SCENE TRACK

RANDOM REPEAT ALL 1 DISC S A< >B MPX INTRO

INDEX STEP

PHONES LEVEL REMOTE SENSOR PROGRAM/REVIEW RANDOM REPEAT

MIN MAX

TV or additional component

AUDIO OUT

FM (INDOOR ANTENNA)

AM loop antenna

AM LOOP

Tape deck

DIGI-LINK STEREO DOUBLE CASSETTE DECK DD-5080C

HIGH NORM CD SYN REC

COUNTER

PLAY(LINE) OUT

AUTO REVERSE

MIN SEC

RELAY P

T SIZE

MEMORY

B/C/OFF

R PLAY

-00 -20 -10 -6 -+3 +6

REVERSE

DUBBING NORMAL HIGH

CD SUN REC

PLAY/AUTO TAPE SELECTOR

MIC MIX MIC

HX-PRO

RECORD & PLAY/AUTO TAPE SELECTOR

REC LEVEL

REC BALANCE

R SOURCE

REC(LINE) IN AUDIO OUT AUDIO IN
Video deck or MD recorder, etc.
V-CD PBC REVERT PEAK PROG AUTO EDIT

RANDOM

SCENE TRACK INDEX

DELETE

REPEAT ALL 1 DISC S A< >B MPX INTRO

PHONES LEVEL PHONES

The VCR jacks may also be connected to an additional component such as MD recorder, tape deck, etc. The TV/AUX jacks may also be connected to an additional component such as a TV, DVD player, etc.

I AC INPUT CORD

Plug this cord into a wall AC outlet.

I CONNECTING SPEAKERS

Speaker A Right Left

Right Speaker B

Usually SPEAKER A terminals are used for only a pair of speakers. When you have another pair of speakers, SPEAKER B terminals can be used. Never short-circuit the + and - speaker cords. Be sure to connect speakers firmly and correctly according to the channel (left and right) and the polarity (+ and -). Note : For safe amplifier operation, use the speakers with impedance of over 8 when you use only SPEAKER A or B terminals and use the speakers with impedance of over 16 when you use both SPEAKER A and B terminals.
Front Panel & Remote Controls

FM MODE MEMORY

DISPLAY

P.SCAN

AUDIO CONTROL

TONE SEL

TREBLE /BASS
REMOTE CONTROL UNIT RM-101
POWER BUTTON Press this button to turn the power on, then the STANDBY indicator goes off. Press again this button to turn the power off, then the STANDBY indicator lights up. STANDBY INDICATOR HEADPHONE JACK Stereo headphones with a standard 1/4 inch plug can be plugged into this jack for private listening. SPEAKER A, B SELECTOR BUTTONS These buttons allow you to select various combinations of speakers as follows: To drive A speakers, press only the SPEAKER A button (SPEAKER A lights up). To drive B speakers, press only the SPEAKER B button (SPEAKER B lights up). To drive both A and B speakers, press the SPEAKER A and B buttons (SPEAKER A and B light up). When using headphones for private listening, press these buttons to switch off the speaker A and B (SPEAKER A and B go off). INPUT SELECTOR BUTTONS Press the button to select the desired input source. TONE BUTTON When adjusting the tone (bass and treble), press this button to select the desired tone mode. Each time this button is pressed, the tone mode is changed to bass or treble. BALANCE BUTTON When adjusting the sound volume balance, press this button to enter the balance mode. BALANCE, TREBLE/BASS UP/DOWN ( , + /-) BUTTONS At the balance mode, adjust the sound volume balance between left and right speakers with these buttons. When the BALANCE + /- buttons on the remote control are pressed, it enters the balance mode automatically without pressing the BALANCE button on the front panel. At the desired tone mode, adjust the tone as desired with these buttons. TONE DIRECT BUTTON Press this button to listen to a program source without the tone effect.
MEMORY BUTTON Press this button to store preset stations. TUNING/PRESET MODE BUTTON Press this button to select the tuning mode or the preset mode. NUMERIC BUTTONS(0 ~ 9) Press these buttons to select or to store preset stations directly. TUNING/PRESET UP/DOWN( BUTTONS Press these buttons to tune in the desired stations. FM MODE BUTTON Press this button to select the desired FM mode. Each time this button is pressed, the FM mode is changed to the stereo mode or the mono mode. PRESET SCAN BUTTON Press this button to scan the stations in the preset sequence. VOLUME CONTROL KNOB, UP/DOWN( ) BUTTONS Adjust the volume to a comfortable listening level with this knob or these buttons. MUTE BUTTON Press this button to temporarily mute the sound. Press again to resume the previous sound level. DISPLAY BUTTON Press this button to select the brightness of units display as desired. Each time this button is pressed, the brightness of units display changes as follows: ON dim OFF

SLEEP BUTTON Press this button to activate the sleep timer for a specified period of time. Each time this button is pressed, the sleep time changes as follows: 90 OFF Unit : minutes
REMOTE SENSOR This receives the signals from the remote control unit. FLUORESCENT DISPLAY For details, see the next page.

FLUORESCENT DISPLAY

REMOTE CONTROL OPERATION RANGE

LOADING BATTERIES

Remove the cover.
Load two batteries matching the polarity.
Use the remote control unit within a range of about 7 meters (23 feet) and angles of up to 30 degrees aiming at the remote sensor.
Remove the batteries when they are not used for a long time. Do not use the rechargeable batteries(Ni-Cd type).
LISTENING TO A PROGRAM SOURCE

Turn the power on.

Operate the selected component for playback.
Adjust the volume to a comfortable listening level.

POWER A SPEAKER B

The unit is turned on and enters the operating mode. To turn the power off, press the POWER button. Then it enters the standby mode and the STANDBY indicator lights up. This means that the unit is not disconnected from the AC mains and a small amount of current is retained to support the operation readiness. In the standby mode, if an INPUT SELECTOR button is pressed, the unit is turned on automatically and the desired input is selected.
Switch the desired speakers on.

To mute the sound.

SPEAKER
REMOTE CONTROL UNIT RM-101 REMOTE CONTROL UNIT RM-101
Then the corresponding speaker indicator lights up and the sound can be heard from the speakers connected to the selected speaker terminals. When using the headphones for private listening, press the corresponding SPEAKER button to switch off both A and B speakers.
MUTE lights up and SPEAKER flickers. To resume the previous sound level, press this button again.
Select the desired input source.

FM/AM CD TAPE TV/AUX VCR

To listen with the headphones.
Each time the FM/AM button on the front panel or the TUNER button on the remote control is pressed, the band is changed to AM or FM.
Be sure to switch off both A and B speakers.

Enter the tone mode.

FM MODE MEMORY DISPLAY SLEEP P.SCAN TUNER

TUNER CD TAPE VCR AUX

AUX AUDIO CONTROL TONE SEL
Each time this button is pressed, the corresponding tone mode is selected and shown for 5 seconds as follows: BAS(s) TRE(ble) Note: When the tone direct function is activated, the tone mode cannot be entered and T-DIR is displayed.
If the tone display disappears, start from the step 8 again. Notes: Extreme settings at high volume may damage your speakers. In general, the bass and treble levels are adjusted to 0.
To listen to a program source without the tone effect.
T-DIR is displayed and the sound that bypasses the tone circuitry will be heard. To cancel the tone direct function, press this button again to display D-OFF.
Adjusting the sound volume balance

Enter the balance mode.

Adjust the sound volume balance between the left and right speakers.
BAL is displayed for 5 seconds.
If the balance display disappears, start from the step 11 again. When the BALANCE + / - buttons on the remote control are pressed, it enters the balance mode automatically without pressing the BALANCE button on the front panel. Note: In general, the balance level is set to the center position(red dot).
Adjusting the tone(bass and treble)
At the desired tone mode, adjust the tone as desired.
LISTENING TO RADIO BROADCASTS

ENGLISH Auto tuning

Select the tuner and then the desired band.

FREQUENCY

Each time this button is pressed, the band is changed to FM or AM.

Select the tuning mode.

Press the TUNING/PRESET UP( ) or DOWN( ) button for more than 0.5 second.

T/P MODE

Each time this button is pressed, the mode changes as follows: Tuning mode : CH goes off. Preset mode : CH lights up.
Then AUTO appears on the display. The tuner will now search until a station of sufficient strength has been found. The display shows the tuned frequency and TUNED. If the station found is not the desired one, simply repeat this operation. Weak stations are skipped during auto tuning.

Manual tuning

Manual tuning is useful when you already know the frequency of the desired station. Perform the steps 1 and 2 in Auto tuning procedure and press the TUNING/PRESET UP( ) or DOWN( ) button repeatedly until the right frequency has been reached.

Presetting radio stations
You can store up to 30 preferred stations in the memory.

Press the MEMORY button.

Tune in the desired station with auto or manual tuning.
MEMO is flickering for 5 seconds.
When using the NUMERIC buttons on the remote control. 3 Examples) For 3 :
MEMORY BACKUP FUNCTION The following items, set before the receiver is turned off, are memorized. INPUT SELECTOR settings Preset stations,etc. Note If the electricity fails or the AC input cord is disconnected for more than 2 weeks, they are all cleared. So you should memorize them again.

For 15 :

within 2 seconds
For 30 : The station has now been stored in the memory. When using the NUMERIC buttons, the station is stored automatically without pressing the MEMORY button. A stored frequency is erased from the memory by storing another frequency in its place. If MEMO goes off, start again from the above step 2.
Tuning to preset stations
After selecting the tuner as an input source, select the preset mode.
Select the desired preset number.
For 30 : Then CH lights up. When selecting the desired preset number with the NUMERIC buttons, the desired preset station will be tuned to automatically without selecting the preset mode.
Listening to FM stereo broadcasts
While listening to FM broadcasts.
Scanning preset stations in sequence

FM MODE

DISPLAY SLEEP P.SCAN TUNER

CD TAPE VCR AUX

Each time this button is pressed, the FM mode changes as follows: Stereo mode : STEREO lights up. Mono mode : STEREO goes off. When FM stereo broadcasts are poor because of weak broadcast signals, select the FM mono mode to reduce the noise, then FM broadcasts are reproduced in monaural sound.
The receiver will start scanning the stations in the preset sequence and each station is received for 5 seconds. At the desired station, press this button again to stop scanning.
Select the desired preset number (1~30) and press the MEMORY button.
Repeat the above steps 1 to 3 to memorize other stations.

RECORDING

The volume, tone(bass, treble) and balance settings have no effect on the recording signals. When you select tuner, CD or AUX as a recording source, recording may be made on TAPE or VCR, or both simultaneously.

Recording with TAPE

Recording with VCR
Select the desired input as a recording source except for TAPE.

FM/AM CD TV/AUX VCR

Select the desired input as a recording source except for VCR.

FM/AM CD TAPE TV/AUX

Start recording on the TAPE.
Start recording on the VCR.
Start play on the desired input.
The audio signals from the desired input will be recorded onto the VCR.

OTHER FUNCTIONS

Operating the sleep timer
The sleep timer allows the receiver to continue to operate for a specified period of time before automatically shutting off. To set the receiver to automatically turn off after the specified period of time.

Adjusting the brightness of the units fluorescent display
Each time this button is pressed, the sleep time changes as follows: 90 OFF

Unit : minutes

Each time this button is pressed, the brightness of the units fluorescent display changes as follows: ON dim OFF In the display OFF mode, pressing any button will restore the display ON mode.
While operating the sleep timer, SLEEP lights up and the units fluorescent display is dimly lit.

Troubleshooting Guide

If a fault occurs, run through the table below before taking your receiver for repair. If the fault persists, attempt to solve it by switching the receiver off and on again. If this fails to resolve the situation, consult your dealer. Under no circumstances should you repair the receiver yourself as this could invalidate the warranty.

PROBLEM

No power

POSSIBLE CAUSE

The AC input cord is disconnected. Poor connection at AC wall outlet or the outlet is inactive. The speaker cords are disconnected. The volume is adjusted too low. The MUTE button on the remote control is pressed to ON. Speakers are not switched on. Incorrect selection of the input source. Incorrect connections between the components. No antenna is connected. The desired station frequency is not tuned in. The antenna is in wrong position. An incorrect station frequency has been memorized. The memorized stations are cleared. No antenna is connected. The antenna is not positioned for the best reception. Weak signals.

REMEDY

Connect the cord securely. Check the outlet using a lamp or another appliance. Check the speaker connections. Adjust the volume. Press the MUTE button to cancel the muting effect. Press the SPEAKER A or B button to ON. Select the desired input source correctly. Make connections correctly.

No sound

Stations cannot be received
Connect an antenna. Tune in the desired station frequency. Move the antenna and retry tuning. Memorize the correct station frequency. Memorize the stations again. Connect an antenna. Change the position of the antenna.
Preset stations cannot be received

Poor FM reception

Continuous hissing noise during FM reception, especially when a stereo broadcast is received. Continuous or intermittent hissing noise during AM reception, especially at night. No recording
Change the position of the antenna. Install an outdoor antenna.
Noise is caused by motors, fluorescent lamps or lightning, etc.
Keep the receiver away from noise sources. Install an outdoor AM antenna. Make connections correctly. Operate each component correctly.
Incorrect selection between the components. Incorrect operation of each component for playback and recording. Batteries are not loaded or exhausted. The remote sensor is obstructed.

Remote control unit does not operate.
Replace the batteries. Remove the obstacle.

Specifications

AMPLIFIER SECTION
Power output, stereo mode, 8 , THD 0.9 %, 50 Hz~20 kHz... W Total harmonic distortion, 8 , 105 W, 1 kHz.... 0.05 % Intermodulation distortion 60 Hz : 7 kHz= 4 : 1 SMPTE, 8 , 105 W.... 0.3 % Input sensitivity, 47 k Line...... 200 mV Signal to noise ratio, IHF A weighted Line...... 95 dB Frequency response Line, 20 Hz~40 kHz...... 3 dB Output level TAPE/VCR OUT, 2.2 k..... 200 mV Bass/Treble control, 100 Hz/10 kHz..... 10 dB

FM TUNER SECTION

Tuning frequency range.... 87.5~108 MHz Usable sensitivity, THD 3%, S/N 30 dB.... 17.2 dBf 50 dB quieting sensitivity, mono/stereo.... 20.8/41.2 dBf Signal to noise ratio, 65 dBf, mono/stereo..... 68/68 dB Total harmonic distortion, 65 dBf, 1 kHz, mono/stereo... 0.5/0.8% Frequency response, 40 Hz~12 kHz..... 3 dB Stereo separation, 1 kHz..... 32 dB Capture ratio...... 4 dB IF rejection ratio..... 75 dB

AM TUNER SECTION

Tuning frequency range.... 520~1710 kHz Usable sensitivity..... 800 V/m Signal to noise ratio..... 40 dB Selectivity..... 25 dB

GENERAL

Power supply.... AC 120 V, 60 Hz Power consumption...... 2.5 A Dimensions (W H D)... 332 mm(17-3/8 5-7/inches) Weight (Net)..... 9.5 kg(20.9 lbs)
Note: Design and specifications are subject to change without notice for improvements.

5707-21054-001-0

5-Disc CDC Changer Programmed and Random Play Toslink Digital Output

CDC-5090R

Key Features Dual 1-Bit (Twin) D/A Converters 5-Disc Carrousel Type 8 Times Oversampling Digital Filter 3-Beam Laser Pickup DTS Digital Out/Optical Digital Output Programmable Memory (32) Music Calendar (14) Play 1/Exchange 4 Random Play (1/ Disc/All) Repeat Mode (1/Disc/All) A-B Repeat (Via Remote) Intro Scan (via remote) Delete Play (Via Remote) Disc Loading Status Display CD Synchro RecordTape Edit Length Adjustment Elapsed/Remaining Time Button Headphone Output Jack Headphone Volume Control (Via Remote) Multi-Function Flourescent Display Display Off/Dimmer Remote Control Digit-Link III operation with other Digi-Link III Sherwood Components Dimensions: (W x H x D): 17 3/8 x 4 3/8 x 15 1/4 Weight: 12 1/2 lbs.

UPC Code: 9

Sherwood America Inc.
13101 Moore Street, Cerritos, CA 90703 Tel: (800) 962-3203 Fax: (562) 741-0967 www.sherwoodamerica.com
Due to ongoing product improvements, Sherwood reserves the right to change product specifications without prior notification. All trademarks and registered trademarks are of their respective owners.
Remote Controlled iPod Doc
Links iPhone, iPod touch, iPod classic, iPod Nano (gen 1, 2 & 3), iPod (gen 4 & 5), iPod mini to audio receivers and systems iPod Video Playback Resume Music and Video Playback Function Component Video output from iPod nano (gen 3) and iPod classic @ 480p or 576p and by iTouch and iPhone @ 480i & 576i On-Screen Display Dedicated Remote Control Compatible with any brand of A/V Receiver Remote Control interoperable with Sherwoods Digi-Link i components Recharges iPod UPC Code: 83488 9
13101 Moore Street, Cerritos, CA 90703 Tel: (800) 962-3203 Fax: (562) 741-0967~8 www.sherwoodamerica.com
HDMI Switcher/Component Video Converter Two x 1 HDMI 1.3 Switching 480p Component Video Input Universal Video Up-Conversion Infrared Remote Control

HSB-600

The HDMI LinkTranscodes 480p Component Video to HDMI and switches 2 HDMI sources
Audio/Video Interface 2 HDMI Inputs Component Video Input Toslink Optical Audio Input HDMI Output Toslink Optical Audio Output RS-232 Serial Control input Infrared Remote Control HDCP Compliant This revolutionary product transcodes (converts) component video (480p) to HDMI (digital video) and adds digital audio to the HDMI data stream, switches two HDMI sources, routes digital audio to Toslink SPDIF output for processing by A/V receiver or pre-pro and is controllable via RS-232 or IR. Dimensions: 17 3/8" W x 2 1/4" H x 9 3/8" D

UPC Code: 44945 8

HSB-6501

UPC Code: 44946 5

Single Zone, High Performance AVR 7.1 DTS-ES, Dolby Digital EX Automatic Speaker Setup Dual Point Room EQ Universal Video Up-Conversion XM Satellite Radio Connect and Play 2 x 1 HDMI Switching 100 Watts x 7
100 Watts per channel x 2 from 20 Hz to 20 kHz with no more than 0.05% THD, 8 ohms 100 Watts per channel for each of 7 channels, surround mode Dolby Digital EX DTS-ES DTS 96/24 DTS Neo -6 Adjustable Dolby Pro Logic IIx Dolby Virtual Speaker Dolby Headphone Totally Discrete Amplifier Stage for all channels 3 DSP Surround modes (Theater, Hall, Stadium) 192 kHz/24 bit Au7.1 channel direct input Automatic Speaker Set-up with Supdio D to A converters for all channels plied Microphone Dual Point Room EQ Quadruple Crossover A/V Synch Delay by Input 3 A/V Inputs and 2 A/V outputs Universal Video Up-Conversion 2 Component Video Inputs Component Video Output 2 HDMI Inputs One HDMI Output 3 Analog Inputs (including tuner) Analog Output 3 composite Video Inputs and 2 composite Video outputs 4 Digital Inputs (2 Coaxial and 2 OptiOptical Digital Output Multi-stage Dynamic Range Control Cinema EQ Tone Direct cal) Speaker On/Off Switch Color Coded Speaker Terminals Quartz PLL Synthesized AM/FM tuning XM Connect and Play 30 AM/FM tuner presets 30 XM tuner presets

Dimensions (H x W x D) (Inches) 5 1/2 x 17 3/8 x 15 Weight: 26 lbs UPC Code: 45349 3
Dual Zone High Performance AVR 2 x 1 HDMI 1.3 Repeater 7.1 DTS-ES, Dolby Digital EX Automatic Speaker Setup SNAP Room EQ Dual-Mode RF + IR Remote Control XM Satellite Radio Ready 100 Watts x 7
R-772 shown with optional side panels
100 Watts per channel from 20 Hz to 20 kHz. Stereo mode, 8 ohms, with <0.05% THD 100 Watts x 7 (Surround Mode) 2 in 1 out HDMI 1.3 switching Decodes DTS Master Audio HD and Dolby Tru HD PCM via HDMI DTS-ES Discrete and Adjustable Dolby Pro Logic IIx Dolby Matrix DTS-96/24 DTS NEO-6 Cinema and Music Dolby Digital EX Headphone Layers 1, 2, 3 Digitally Re-Masters PCM input to 96 kHz/ 24-bit Automatic Format Detection 192 kHz 24-bit Crossover frequency 40 to 250 Hz A/V Synch delay by DACs for all channels Dolby Virtual Speaker Pure Audio Mode input Firmware upgradeable SNAP 12-band parametric EQ per channel RS-232 Universal Video upconverts composite and S-Video to Component Video 2 Optical and 2 Co-ax Digital Inputs Digital Output On Screen Display (available from all video outputs) RF + IR Learning remote Programmable Input Labeling Crystal 32-Bit DSP processor 8 DSP Modes 7.1 channel direct input Subwoofer Pre-Amp Output Room 2 A/V Output w/ fixed/variable audio level, composite Automatic 7.1 to 5.1 + Stereo Lockable Installer Memory Rear Panel Room-2 IR control with 1 input and 1 output Dedicated 4 Rear Panel AuRoom 2 Remote 12-Volt Trigger 2 HDTV-Ready Component Video Inputs Component Video Output dio/Video Inputs 4 Audio Inputs Front Panel A/V Input Including S-Video Cinema EQ Tone Defeat Automatic set-up 10-step Dynamic Range Control Totally Discrete Amplifier Stage for speaker level and distance Channel Level Memory Heavy Duty Speaker Binding Posts XM Connect and Play XM Neural Surround 4 Gang FM tuner Preset (TDAS) Scan 30 XM Presets 30 AM/FM Station Presets Digi-Link III Sleep Timer Aluminum Front Panel
Dimensions (H x W x D) (Inches) 5 1/2 x 17 3/8 x 15 Weight: 26 lbs UPC Code: 83101 7
High Performance A/V Receiver Dolby and DTS Lossless Audio Converts All Video to HDMI HDMI 1.3 Repeater with Three Inputs Dual-Zone Operation Blue Tooth Music Streaming from PC or Phone* Sirius Ready; DS-10 iPod Doc Ready
100 Watts RMS per channel with no more than 0.2% THD, from 20 Hz to 20 kHz, 6 ohms
100 Watts per channel with no more than 0.2% THD into 6 ohms for each of 7 channels HDMI 1.3 Repeater Lossless Audio DTS-HDMaster Audio Dolby TrueHD DTS 96/24; ES; Neo6 Dolby: DPLIIx: DSD (SACD) LMP (DVD-A) Totally Discrete Amplifier Stage for all channels Multi-Source, Dual-Zone operation 8 DSP Surround modes (Theater, Hall, Stadium, etc.) 192 kHz/24 bit Audio D to A converters for all channels Multi-source, dual-zone 7.1 SNAP Room EQ channel direct input Automatic Speaker Set-up with Supplied Microphone Quadruple Crossover A/V Synch Delay by Input 3 A/V Inputs and 2 A/V outputs Anchor Bay ABT-2010 converts all video to display resolution including 1080p via HDMI Component Video Inputs Component Video Output 3 HDMI Inputs One HDMI Output 8 Analog Inputs (including tuner) Analog Output Composite and S-Video with 3 in and 2 out 4 Digital Inputs (2 Coaxial and 2 Optical) Optical Digital Output Multi-stage Dynamic Range Control Cinema EQ Tone Direct Speaker On/Off Switch Color Coded Speaker Terminals Quartz PLL Synthesized AM/FM tuning Sirius Ready 30 AM/FM tuner presets Dual-Mode RF + IR Preprogrammed remote control RS-232 Serial control IR-Output 12-Volt Trigger Output Front panel receptacle for optional BT receiver Sherwood DigiLink-i compatible for remote interoperability with Sherwood DS-10 iPod doc * With Optional Sherwood BT-R7 Bluetooth receiver

Dimensions: 17 1/8 W x 6 11/16 H x 15 D Weight: 30 lbs. UPC Code: 83847 4
100 W x 7 Audiophile A/V Receiver 4 x 1 HDMI; Lossless Audio Faroudja DCDi Processing SNAP Room EQ Multi-Source, Dual-Zone
100 Watts per channel from 20 Hz to 20 kHz. Stereo mode, 8 ohms, with <0.05% THD 100 Watts x 7 (Surround Mode) 4 in 1 out HDMI 1.3 switching Scales 480i, 480p, 720p, 1080i and all analog video to 720p/1080i/1080p Faroudja 2301 Scaler/Deinterlacer Decodes DTS Master Audio HD and Dolby Tru HD DTS-ES Discrete and Matrix DTS-96/24 DTS NEO-6 Cinema and Music Dolby Digital EX Adjustable Dolby Pro Logic IIx Dolby 192 kHz Headphone Layers 1, 2, 3 Digitally Re-Masters PCM input to 96 kHz/ 24-bit Automatic Format Detection 24-bit DACs for all channels Dolby Virtual Speaker Pure Audio Mode Crossover frequency 40 to 250 Hz A/V Synch delay by input Firmware upgradeable SNAP 12-band EQ per channel RS-232 and USB Universal Video 4 Optical and 2 Co-ax Digital Inputs Digital Output On upconverts composite and S-Video to Component Video Screen Display (available from all video outputs) RF + IR Learning remote with LCD display Programmable Input Crystal 32-Bit DSP processor 8 DSP Modes 7.1 channel direct input 8 Pre-Amp Outputs (L, C, R, L. Labeling Surround, L Rear Center Surround, R Rear Center Surround, R. Surround, Subwoofer) Room 2 A/V Output w/ fixed/ Lockable Installer Memory Rear Panel Room-2 IR variable audio level, S-Video Automatic 7.1 to 5.1 + Stereo control with 1 input and 1 output Dedicated Room 2 Remote 12-Volt Trigger 3 HDTV-Ready Component Video 4 Rear Panel Audio/Video Inputs 4 Audio Inputs Front Panel A/V Input Inputs Component Video Output Including S-Video and Optical Digital Cinema EQ Tone Defeat Automatic set-up for speaker level and distance Channel Level Memory 10-step Dynamic Range Control Totally Discrete Amplifier Stage (TDAS) Heavy Duty Speaker Binding Posts XM Connect and Play XM Neural Surround 4 Gang FM tuner Preset Scan 30 XM 30 AM/FM Station Presets Digi-Link III Sleep Presets
Dimensions: 17 3/8 W x 6 H x 15 D Weight: 31 lbs. UPC Code: 45406 3
13101 Moore Street, Cerritos, CA 90703 Tel: (800) 962-3203 Fax: (562) 741-0967 www.sherwoodusa.com
High Performance A/V Receiver Dolby Digital, 100 Watts x 5 Automatic Speaker Setup SNAP Room EQ 2 x 1 HDMI Repeater Blue Tooth Music Streaming from PC or Phone*

RD-6504

100 Watts RMS per channel with no more than 0.2% THD, from 40 Hz to 20 kHz, 6 ohms
100 Watts per channel with no more than 0.2% THD into 8 ohms for each of 5 channels Dolby Digital EX Adjustable Dolby Pro Logic IIx Totally Discrete Amplifier Stage for all channels 3 DSP Surround modes (Theater, Hall, Stadium) 192 kHz/24 bit Audio D to A converters for all channels 5.1 channel direct input Automatic Speaker Set-up with Supplied Microphone SNAP (12-Band Automatic Parametric) Room EQ 5-Band User adjustable Parametric EQ 2 A/ V Inputs and 2 A/V outputs 2 Component Video Inputs Component Video Output 2 HDMI Inputs One HDMI Output 3 Analog Audio Inputs (including tuner) Analog Output 2 Compos3 Digital Inputs (2 Coaxial and 1 Optical) ite Video Inputs and 2 Composite Video outputs Multi-stage Dynamic Range Control Cinema EQ Tone Direct Speaker On/Off Switch Color Coded Speaker Terminals Quartz PLL Synthesized AM/FM tuning 30 AM/FM tuner presets Front Panel Blue Tooth Receptacle (* with Optional Blue Tooth Receiver)

Dimensions: 17 3/8 W x 5 1/2 H x 15 D Weight: 23 lbs. UPC Code: 83525 1
High Performance A/V Receiver Dolby Digital, 100 Watts x 5 Automatic Speaker Setup SNAP Room EQ 2 x 1 HDMI Switching Blue Tooth Music Streaming from PC or Phone*

RD-6513

Dimensions: 17 3/8 W x 5 1/2 H x 15 D Weight: 23 lbs. UPC Code: 83083 6
High Performance A/V Receiver Dolby and DTS Lossless Audio HDMI 1.3 Repeater with Three Inputs Dual-Zone Operation Blue Tooth Music Streaming from PC or Phone*

RD-7503

100 Watts RMS per channel with no more than 0.2% THD, from 20 Hz to 20 kHz, 8 ohms
100 Watts per channel with no more than 0.2% THD into 8 ohms for each of 7 channels HDMI 1.3 Repeater Lossless Audio DTS Master Audio HD Dolby TrueHD DTS 96/24; ES; Neo6 Dolby: DPLIIx: Virtual Speaker; Headphone DSD (SACD) LMP (DVD-A) Totally Discrete Amplifier Stage for all channels Multi-Source, Dual-Zone operation 8 DSP Surround modes (Theater, Hall, Stadium, etc.) 192 kHz/24 bit Audio D to A converters for all channels Digitally remasters PCM to 96 kHz/24Bit Multi-source, dual-zone 7.1 channel direct input Automatic Speaker Set-up with Supplied Microphone SNAP Room EQ Quadruple CrossA/V Synch Delay by Input 3 A/V Inputs and 2 A/V outputs 2 Component Video Inover puts Component Video Output 3 HDMI Inputs One HDMI Output 8 Analog Inputs (including tuner) Analog Output Composite and S-Video with 3 in and 2 out 4 Digital Inputs (2 Coaxial and 2 Optical) Optical Digital Output Multi-stage Dynamic Range Control Cinema EQ Tone Direct Speaker On/Off Switch Color Coded Speaker Terminals Quartz PLL Synthesized AM/FM tuning Sirius Ready 30 AM/FM tuner presets Preprogrammed IR remote control Blue Tooth front panel receptacle for optional BT receiver * With Optional Bluetooth receiver
Dimensions: 17 1/8 W x 6 11/16 H x 15 D Weight: 30 lbs. UPC Code: 83346 2

RD-8504

100 Watts per channel with no more than 0.2% THD into 6 ohms for each of 7 channels HDMI 1.3 Repeater Lossless Audio DTS-HD Master Audio Dolby TrueHD DTS 96/24; ES; Neo6 Dolby: DPLIIx DSD (SACD) LMP (DVD-A) Totally Discrete Amplifier Stage for all channels Multi-Source, Dual-Zone operation 8 DSP Surround modes (Theater, Hall, Stadium, etc.) 192 kHz/24 bit Audio D to A converters for all channels Multi-source, dual-zone 7.1 channel SNAP Room EQ Quaddirect input Automatic Speaker Set-up with Supplied Microphone A/V Synch Delay by Input 3 A/V Inputs and 2 A/V outputs Anchor Bay ABT ruple Crossover -2010 converts all video to display resolution including 1080p via HDMI Component Video Inputs Component Video Output 3 HDMI Inputs One HDMI Output 8 Analog Inputs (including tuner) Analog Output Composite and S-Video with 3 in and 2 out 4 Digital Inputs (2 Coaxial and 2 Optical) Optical Digital Output Multi-stage Dynamic Range Control Cinema EQ Tone Direct Speaker On/Off Switch Color Coded Speaker Terminals Quartz PLL Synthesized AM/FM tuning Sirius Ready 30 AM/FM tuner presets Preprogrammed IR remote control Front panel receptacle for optional BT receiver Sherwood DigiLink-i compatible for remote interoperability with Sherwood DS-10 iPod doc * With Optional Sherwood BT-R7 Bluetooth receiver

Dimensions: 17 1/8 W x 6 11/16 H x 15 D Weight: 30 lbs. UPC Code: To be announced

RD-7502

Dimensions (H x W x D) (Inches) 5 1/2 x 17 3/8 x 15 Weight: 26 lbs UPC Code: 45101 7
105 Watts X 2 Stereo Receiver Remote Control, All Discrete Amps A/B Speaker switching from remote

RX-4103

105 Watts RMS per channel with no more than 0.9% THD, from 40 Hz to 20 kHz, 8 ohms
Unlike the budget stereo receivers now flooding the entry-level price points at dealers across the country, the new Sherwood RX-4103 is designed and built in-house with the same quality and attention to detail we have been bringing to our audio gear for the last 50 years. With 105 Watts RMS per channel, a versatile remote control and switching for two pair of loudspeakers, the only thing that bespeaks the word budget about the RX-4103 is its modest cost.

Key Features

Totally Discrete Amplifiers for all chan

Performance Ratings

Input Sensitivity IM Distortion (rated output)
nels (TDAS) Switching for two pair of loudspeakers (in parallel) 25-Key Remote Control AM and FM Stereo Tuning 30 Station Presets 5 Audio Inputs (Including Tuner) Sleep Timer Bass and Treble Tone Controls

General Features

Digital Encoder Volume Control System Illumination (Dimmer) Headphone Jack
200 mV <0.3% S/N Ratio 90 dB IHF FM Sensitivity 17.2 dBf Tuner S/N Ratio (Mono/Stereo) 68 /68 dB FM THD (Mono/Stereo) 0.3%/0.4% Selectivity 55 dB Stereo Separation 40 dB FM Frequency Response kHz, +/- 1 dB AM Sensitivity 800 uV/M AM Frequency Response 100 Hz2.3 kHz
Tone Direct Large Fluorescent Display UPC Code: 18 lbs. Due to ongoing product improvements, Sherwood reserves the right to change product specifications without prior notification. All trademarks and registered trademarks are of their respective owners.

Dimensions and Weight

17 3/8" W x 5" H x 13"
100 Watts X 2 Stereo Receiver Remote Control, All Discrete Amps A/B Speaker switching from remote

RX-4105

In our modern, surround sound driven universe, one might think that mere Stereo is old fashioned. But dont be mislead. Humans have only two ears and stereo is still a significant life form. Our case in pointthe new Sherwood RX-4105. Rated at 100 watts x 2, distortion is less than 0.20% from 20 Hz to 20 kHz into 8 ohms. The RX -4105s AM/FM tuner has the ability to pre-set up to 30 favorite stations. It has inputs for 4 audio sources. And the sound is phenomenalas youd expect from a company that dates its own existence to before stereos birth. The RX-4105 has at least one unexpected grace: the ability to independently select up to two sets of loudspeakers via the supplied remote control. (Audio purists will be pleased to know that this relay controlled switching puts the speakers in parallel maintaining their individual sound qualities.) Key Features

100 Watts X 2 Stereo Receiver Phono Section, All Discrete Amps Binding Posts, Remote Control

RX-4109

100 Watts RMS per channel with no more than 0.9% THD, from 40 Hz to 20 kHz, 6 ohms
Unlike the budget stereo receivers now flooding the entry-level price points at dealers across the country, the new Sherwood RX-4109 is designed and built in-house with the same quality and attention to detail we have been bringing to our audio gear for the last 50 years. With 100 Watts RMS per channel, phono section, binding posts, a versatile remote control and switching for two pair of loudspeakers, the only thing that bespeaks the word budget about the RX-4109 is its modest cost.
Surround Sound Stereo Receiver Dolby Virtual Speaker and Headphone Optimized for Blu-Ray Bluetooth option for Audio Streaming from PC or Phone
RX-4503 Virtual Surround Receiver
A new concept for retail. Merchandise Blu-Ray players with a Sherwood Virtual Surround sound receiver. With 5.1 analog inputs and subwoofer output, Sherwoods new RX-2.1 Virtual Surround receiver accepts audio from Blu -Ray and DVD players and gives consumers an easy-to-install and easy-to-use adoption path for surround sound. By using our built-in Dolby Headphone, your customers can even self-demo this amazing technology. For the icing on the cake, show them how they can stream MP3 files from the latest cell phones direct to the Sherwood. Once consumers hear the RX-4503, theyll recognize that stereo is alive and well. Its only 5.1 thats on life-support. Key Features
Totally Discrete Amplifiers for all channels
(TDAS) 100 W RMS x 2, 40 Hz-20 kHz, 6, with less than 0.2% THD Switching for four pair of loudspeakers (in parallel); Speaker On/Off Switch IR Remote Control AM & FM Stereo Tuning/30 presets 30 Station Presets Sleep Timer
Digital Encoder Volume Control System Illumination (Dimmer) Headphone Jack Tone Direct Large Fluorescent Display UPC Code:

83085 0

17 3/8" W x 5" H x 13"; 18 lbs.
Dual-Zone, Dual-Source Stereo Receiver Switching for Four Pair of Speakers

RX-5502

In our modern, surround sound driven universe, one might think that mere Stereo is old fashioned. But dont be misled. Humans have only two ears and stereo is still a significant life form. Our case in pointthe new Sherwood RX-5502. With independent speaker selection for up to 4 pair of loudspeakers, the RX-5502 is adept at powering multi-room audio setups, yet is economical enough to serve a single room. Rated at 70 watts RMS x 4 (with 100 watts per channel into 4 ohms), distortion is less than 0.20% from 20 Hz to 20 kHz into 8 ohms. Key Features Performance Ratings

Totally Discrete Amplifiers for all chan Input Sensitivity
nels (TDAS) Switching for four pair of loudspeakers (in parallel) 25-Key Remote Control Phono Input AM and FM Stereo Tuning 30 Station Presets 5 Audio Inputs (Including Tuner) Sleep Timer Bass and Treble Tone Controls
IM Distortion (rated output)
200 mV <0.3% S/N Ratio 90 dB IHF FM Sensitivity 17.2 dBf Tuner S/N Ratio (Mono/Stereo) 68 /68 dB FM THD (Mono/Stereo) 0.3%/0.4% Selectivity 55 dB Stereo Separation 40 dB FM Frequency Response kHz, +/- 1 dB AM Sensitivity 800 V/M AM Frequency Response 100 Hz2.3 kHz
Tone Direct Large Fluorescent Display UPC Code:

45394 3

17 3/8" W x 5" H x 13" 18 lbs.
13101 Moore Street, Cerritos, CA 90703 Tel: (800) 962-3203, Fax: (562) 741-0967~8 www.sherwoodamerica.com
RF Controlled, XM-Ready Dual-Zone, Dual-Source Stereo Receiver Switching for Four Pair of Speakers Audio Streaming from PC and Phone*

RX-773

Multi-zone playback has never been easier. The new RX-773 comes complete with dual-mode IR plus RF remote. Since each unit is independently addressable, stack several in a central location, operate 6 zones and up to 12 rooms via RF and do it all without a keypad. Use the optional Blue Tooth receiver to stream MP3s from your cell phone to any room. The 773 is even XM ready. With independent speaker selection for up to 4 pair of loudspeakers, the 773 is adept at powering multi-room audio setups, yet is economical enough to serve a single room. Rated at 70 watts 4 (with 100 watts per channel into 4 ohms), distortion is less than 0.20% from 20 Hz -20 kHz into 8 ohms. * with Optional Bluetooth receiver Key Features
Totally Discrete Amplifiers for all chan
Input Sensitivity IM Distortion (rated output)
nels (TDAS) Switching for four pair of loudspeakers (in parallel) 61-Key Remote Control Phono Input AM and FM Stereo Tuning 30 Station Presets 5 Audio Inputs + AM/FM/XM Sleep Timer Bass and Treble Tone Controls
200 mV <0.3% S/N Ratio 90 dB IHF FM Sensitivity 17.2 dBf Tuner S/N Ratio (Mono/Stereo) 68 /68 dB FM THD (Mono/Stereo) 0.3%/0.4% Selectivity 55 dB Stereo Separation 40 dB FM Frequency Response kHz, +/- 1 dB AM Sensitivity 800 V/M AM Frequency Response 100 Hz2.3 kHz Tone Direct Large Fluorescent Display
17 3/8" W x 5" H x 13" 18 lbs. UPC Code: Due to ongoing product improvements, Sherwood reserves the right to change product specifications without prior notification. All trademarks and registered trademarks are of their respective owners.

Newcastle additions for WCES: Two Universal DVD Players with DVD-A and SACD. New 7.1 A/V Receiver suitable For Custom Installation
SD-860 Universal CD/DVD/DVD-A/SACD Player DVD +/- R/RW, CD-R/RW compatible SACD, DVD-Audio/DVD-Video playback MP-3, JPEG, Kodak Picture CD Playback WMA/WMV Playback DivX Playback Progressive Scan playback 192 kHz/24-Bit Audio DACs 480p Component Video Output Two each S-Video and composite Video outputs 5.1/7.1 channel Audio Outputs plus One each coaxial and optical digital audio outputs 2-channel audio downmix output Pure Audio Mode turns off all video processing Pure Black Mode allows black level adjustment (7.5 IRE or 0 IRE) Sherwood Digi Link III communication protocol Aluminum front panel

UPC Code: 44625 9

SD-871 Universal CD/DVD/DVD-A/SACD Player SACD, DVD-Audio/DVD-Video playback DVD +/- R/RW, CD-R/RW compatible MP-3, JPEG, Kodak Picture CD Playback WMA Playback DivX Playback Progressive Scan playback 192 kHz/24-Bit Audio DACs Faroudja DCDI processing HDMI 216 MHz/12 Digital output (HDCP: 720p/1080i Video output, 192 kHz audio output) bit video DACs 2 Pair component video outputs (RCA and BNC) RS-232C control input 480p Component Video Output Two each S-Video and composite Video outputs 5.1/7.1 channel Audio Outputs plus 2-channel audio downmix output One each coaxial and optical digital audio outputs Pure Audio Mode turns off all video processing Pure Black Mode allows black level adjustment (7.5 IRE or 0 IRE) Sherwood Digi Link III communication protocol Aluminum front panel UPC Code: 44623 5
7.1 A/V Receiver for Custom Installation
100 Watts per Channel from 20 Hz-20 kHz in Stereo Mode, 8 ohms, with <0.20% THD 100 Watts per Channel x 7 in Surround Mode DTS-ES Discrete and Matrix DTS-96/24 DTS NEO6 Movie and Music Dolby Digital EX Dolby Pro Logic IIx adjustable for Movie, Music, Matrix, Emulated + Parameter Control Dolby Virtual Speaker Dolby Headphone Automatic Format Detection 192 kHz 24-bit DAC's for all channels Crossover frequency selectable at 40 Hz-120 Hz in 20 Hz increments Automatic Speaker Set-up with supplied microphone Dual-Point Room EQ Operating System is software upgradeable via RS-232 Universal Video upconverts composite and S-Video to Component Video A/V Synch Delay Discrete On/Off IR codes 2 Optical and 2 Co-ax Digital Inputs Digital Output On Screen Display (available from all video outputs) 8unit Preprogrammed Remote Control 32-Bit TI processor 12 DSP Modes 7.1 channel direct input Room 2 A/V Output with fixed/variable audio level Rear Center amps assignable to Room2 feed 3 HDTV-Ready Component Video Inputs Component Video Output 3 Rear Panel Audio/Video Inputs 2 Audio Inputs Front Panel A/V Input Cinema EQ Dynamic Range Control Totally Discrete Amplifier Stage (TDAS) Heavy Duty Speaker Binding Posts Quartz PLL Synthesized Digital Tuning Direct Frequency Input Preset Scan 30 Station Presets Digi-Link III 24K Gold In/Out Jacks Sleep Timer Dimensions: 17 3/8 W x 5 H x 15 D

UPC Code: 44835 2

All specifications are subject to change without notice. All copyrights are the property of their respective copyright holder.
Progressive Scan DVD, CD, CDR, CDR-W, CD-MP3 and VCD Player

VD-4500

For nearly 50 years, the Sherwood brand has been synonymous with high performance, value priced gear. Now, finally, theres a Sherwood DVD/CD player that matches both physically and philosophically.
Plays virtually all of todays optical software including DVDs, DVD-Rs, DVDRWs, DVD+Rs, DVD+RWs, CDs, CDRs, CD-RWs, MP-3, WMA and HDCD encoded CDs, VCDs, S-VCDs, JPG, Kodak and Fuji Photo CDs Coaxial and Optical digital output for DTS or Dolby Digital decoding by an external amplifier or receiver Component, S-Video and composite video output 54 MHz, 10 bit Video DACs 96 MHz, 24 bit Audio DACs Supports 96 MHz 24-bit audio playback Programmable, repeat and random playback Specifications Video Audio Output: Output: S/N Ratio, 1 kHz, 20 kHz LPF: Dynamic Range: Channel Separation: THD: Dimensions and Weight 17 3/8" W x 3 3/16" H x 9" UPC Code: 81762 2
5-mode repeat including: Disc, Title, Chapter, Track and A<->B 3-Speed Forward and Reverse Slow playback (1/8, 1/4 and 1/2 Speed) 6-Speed Forward and Reverse Picture Search (2, 4, 8, 16, 32 and 64 times normal) Direct Access to Title, Chapter, Track and Time Supports Multiple Angle view 2-Mode Zoom Playback 3-Scene Marker On-Screen Display Full featured Infrared remote control
1 Volt Peak to Peak, 75 ohms 2 Volts RMS 110 dB 108 dB 95 dB 0.01% 6lbs. 8 oz.

Sherwood America Inc