General safety instructions
This washer dryer meets the relevant safety require ments.
Before starting operation
- Install the washer dryer in accordance with the installation instructions, page 48. - Remove and keep the transport protection devi ces. - Do not connect the washer dryer if it has visible damage. If in doubt consult customer service or dealer. - Read the enclosed documents carefully. They contain important information for installation, use, and safety of the appliance.
Using your washer dryer correctly
This washer dryer is intended for: - use in the household only - washing machinewashable textiles in water and drying this textiles - operation with commercially available detergents and cleaning products which are suitable for use in washing machines. Do not use the washer dryer if: - the laundry has been treated with a solvent or has been colourtreated (e.g. stain remover, petroleum ether). - the laundry contains dust, e.g. coal dust or flour - the laundry contains foam/rubber - the laundry contains traces of hairspray, nail var nish remover or similar substances.
When washing and drying please note
- Remove all objects from pockets, especially ligh ters. - Do not leave children unsupervised with the ap pliance. - Keep pets away from the appliance. - Do not insert/pull out the mains plug with wet hands. - Do not pull out the mains plug by tugging the ca ble. - Caution when draining hot water. - Do not climb onto the washer dryer. - Do not lean on the open washer dryer door. - Do not install the washer dryer in a room where there is a risk of freezing. - Transit bolts must be in position for transport.
Looking after your washer dryer

Your New washer dryer

Filling laundry detergent and/or additive dispensers Dispenser 1: Detergent for prewash or presoaking agent. Dispenser 2: Detergent for main wash Dispenser 2: Additives, e.g. fabric softener or starch.

Service flap

Open the door.

and close it.

Control panel
Display panel Indicates the settings which have been selected (e.g. spin speed, time delay) as well as programme progress and the programme state. Option lights W delay, X end, B spin determine the dis play's content. Y dry: Normal heat selected for drying Z delicate: Low heat selected for drying h door button For opening the door.

M start button For starting and pausing the cycles.
Buttons I quick (in addition to the programme if required): Shortened programme duration W delay (in addition to the programme if required): Selects the start time (delays the start of the pro gramme). Y dry: Selects the drying mode and the drying time B spin: Selects the spin speed or without final spin". The indicator lights of the buttons come on, if the options are active.
Programme selector For switching the washer dryer on and off and for selecting the programme. Can be rotated in either direction. The programme selector does not rotate while the programme is running. The programme sequence is electronically controlled.
Description of the washer dryer
Operation and special features
This washer dryer allows - washonly - dryonly - wash+dry programmes to be set. In the latter programmes, the cycle shifts automatically from washing to drying wi thout having to touch the controls to continue the cy cle after washing. The drying works on the principle of condensation. The condensation produced during the drying cycle use the drain hose into the basin for draining. The water tap must be left open and the drain hose must be correctly positioned during drying cycles. The door The washer dryer is fitted with a safety device that prevents the door from opening while it is working. Make sure there is no water in the tub and that the drum is not moving. Open the door after finishing a programm q Wait until END appears on the display. q Press the h door button on the front panel.

The signal

The acoustic signal indicates: pressing a button start of programme end of programme operating errors and faults.
q Press the I quick and W delay button simultaneously to activate or deactivate the signal. The display indicates j or i. i The volume of the signal cannot be changed. The programme state Press the B spin button to show the programme state in the display. After the topical spin speed the programm state will be visualized. When the washer dryer is in the washing cycle there is the symbol shown in the Q (washing) part of the display. When the washer dryer is in the drying cycle there is the symbol shown in the Y (Drying) part of the display.
Preparing and sorting the laundry

Preparing the washing

Warning Loose debris (e.g. coins, paper clips, needles, nails) can damage items of clothing as well as parts of the washer dryer (e.g. drum). q Empty all pockets on items of clothing. q Brush sand out of pockets and cuffs/turnups. q Close zips, fasten pillow cases/cushion covers. q Remove curtain runners or tie up in a net/bag. q Wash in a net/cushion cover: - delicates, e.g. tights, curtains, - small laundry items, e.g. socks or handkerchiefs, - underwired bras (underwire may become detached during washing and cause damage). q Trousers, knitwear and knitted textiles, e.g. jersey garments, Tshirts or sweatshirts should be turned inside out. q Do not wash unhemmed or torn garments as they may fray.

Sorting the laundry for washing
According to colour and degree of dirt
Warning Washing may become discoloured. Do not wash new coloured washing with other washing.
White items may become grey. Wash white and coloured items separately.

Degrees of dirt

Lightly soiled No visible soiling or stains. Washing has probably absorbed body odour. - Lightweight summer clothing and sportswear worn for several hours. - Tshirts, shirts, blouses worn for up to one day. - Bed linen, guest towels used for one day. Normally soiled Visible soiling and/or a few light stains. - Tshirts, shirts, blouses soaked in sweat or worn several times. - Underpants, briefs worn for one day. - Tea towels, hand towels, bed linen used for up to one week. - Curtains (without nicotine soiling) used for up to six months.
Very soiled Visible soiling and/or stains. - Kitchen towels used for up to one week. - Fabric serviettes. - Baby bibs. - Children's outer clothing or football jerseys and shorts soiled with grass and/or earth. - Work clothes, e.g. mechanic's overalls, baker's and butcher's clothing. Typical stains - Skin grease, cooking oil/fat, sauces, mineral oil, wax (containing fat/oil). - Tea, coffee, red wine, fruit, vegetables (which can be bleached). - Blood, egg, milk, starch (containing protein, carbohydrate). - Soot, earth, sand (pigments), tennis clothing soiled with red clay. Removing stains Remove/pretreat stains as soon as possible after they have occurred. First dab with a soapy solution. Do not rub. Then select the appropriate programme and wash the item. i Stubborn/dried in stains can sometimes only be removed by washing several times.
Sorting washing according to the instructions on the care labels
Only wash laundry that is labelled with the following care symbols:

Cottons 90 C

Coloureds 60 C, 40 C, 30 C
Easycare 60 C, 40 C, 30 C
Handwashable and machinewashable silk and wool, cold, 40 C, 30 C Do not wash laundry items which bear the following care label in the washer dryer:

B = do not wash

Sort the laundry with due consideration for maximum loads. Do not overload the washer dryer as this leads to poor washing results. Maximum laundry loads for washing Whites/coloureds Easycare, delicates, Machine washable wool and silk 5 kg 2.5 kg 1.0 kg
Sorting the laundry for drying
Warning Sort the laundry according to the care symbols on the labels. Use to machinedry only laundry that is labelled "dry ersafe", or that is identified by the following care sym bols: = Dry at normal temperature = Dry at low temperature (Gentle drying) Do not dry the following garments in this washer dryer: Laundry that is identified with the following care sym bol: = Do not dry in a tumble dryer. - Airtight fabrics (e.g. rubbercoated fabrics). - Delicate materials (silk, curtains made from synthe tic material) they may crease. - Drippingwet laundry high energy consump tion. - Wool or fabrics containing wool. - Observe the manufacturer's instructions. i Keep the maximum machine load in mind. Do not overload the washer dryer.

Maximum laundry loads for drying
Cottons / coloureds Easycare

2.5 kg 1.5 kg

Energy conservation
It is advisable to wash cottons / coloureds always in full machine loads (5 kg), subsequently making small er loads for drying. q Only use the drying facility for laundry which has been washed, rinsed and spun. q Easycare laundry should have been spun at the relevant speed (see programme chart) before be ing tumble dried. q For best results, sort the washing according to fibre type and desired level of dryness. q Take delicate laundry out of the washer dryer whilst it is still slightly damp. Let it briefly dry out in the air as overdrying in the washer dryer may cause creasing. q It is not necessary to iron the laundry immediately after drying. We recommend that before ironing items are folded or rolled up so that residual mois ture can spread evenly through the laundry.

Practical tips

Detergents and cleaning products

Dosing detergent

d Risk of poisoning! Keep detergents and cleaning products out of the reach of children. Dose detergent according to q the water hardness. You can find out the water hardness from your water utility company. q the specifications of the detergent manufacturer. q the amount of laundry. q the degree of soiling. i The correct dosage reduces the impact on the environment and produces a good washing result. i The detergent quantities indicated on the packets refer to full machine loads. With less laundry or if the laundry is only lightly soi led, reduce the quantity of detergent. i For the wool programme, only use phneutral detergents for woollens. Water hardness Hardness level Soft Moderately hard Hard Very hard French degree fH Up to - - 40 Over 40 German degree dH Up to - - 22 Over 22

Dosing powder detergent

Normal dirty washing q Choose a programme without prewash. q Pour the total quantity of detergent indicated on the packs into dispenser 2 of the detergent dra wer. Very dirty washing q Choose a programme with prewash. q Add of the recommended quantity of detergent into dispenser 1 of the detergent drawer and of the detergent into dispenser 2.

Dosing liquid detergent

i Use liquid detergents only for the main washing cycle, without prewash. q Pour the recommended dose into the batcher supplied with the liquid detergent and place it in side the drum or q Pour the liquid detergent into dispenser 2 of the detergent drawer after fitting the relative red insert A. i The scale on the red insert will help you to use the right quantity of liquid detergent. i When dispenser 2 is used for powder detergent, the red insert A must be removed. Liquid detergents and start time delay Start time delay, page 28. With time delay selection use a dosage container for liquid detergents, e.g. a ball, otherwise the liquid de tergent will run slowly out of the soap dispenser and congeal. Take dosage container out of the drum at the end of the programme.

Filling detergent/ cleaning product
Dispenser 1 Detergent for prewash. Dispenser 2 Detergent for main wash. Machine accessories include a red insert A that can be placed inside dispenser 2 to allow liquid detergent to be used. Dispenser 2 (3) Pour liquid additives such as starch and fabric softe ner. The additives are automatically introduced into the tub during final rinsing. i The level of the liquids must not exceed the maxi mum limit, otherwise the trays will be emptied too soon. i Before pouring thick additives into the tray, dilute them with a little water to prevent them from ob structing the trap. Dispenser 4 is used for bleach. i If there is a cover marked , this means that bleach cannot be used with this model of machi ne. q Pull out the detergent drawer. q Pour in detergent and/or cleaning product. q Close the detergent drawer.

Scaleremovers

Scaleremovers can be introduced into dispenser 1 and 2 according to the manufacturer's indications. First, add the detergent and then the scaleremover.

First wash

The washer dryer was tested before leaving the facto ry. To remove any residual test water, wash the first time without any laundry. q Check that the transport protection devices have been removed from the back of the washer dryer, page 51. q Do not load any laundry. q Close the door. q Open the water tap. q Pull out the detergent drawer all the way. q Put half a measuring cup of normal detergent into dispenser 2. i Do not use any special detergents for woollens or delicates (foam formation). q Close the detergent drawer. q Set the programme selector to the required pro gramme, e.g. y cotton 60 C. q Press the M start button. q When the programme has ended, set the pro gramme selector to the off position. q Open the door. i Leave the door ajar in order to allow the inside of the washer dryer to dry.

Programmes and functions

Programme selector
Washing programmes The programmes are set using the programme selec tor which can be turned in both directions. The pro gramme selector must not be set to intermediate positions between the indicated programmes. Intensive washing programme y 30, 40, 60, 75 C Intensive washing programme for resistant cotton, coloured or hemp fabrics. Maximum load: 5.0 kg Intensive washing programme with prewash 60, 90 C + P For heavily soiled laundry with stains and for work wear/overalls. Put 1/4 cup of the detergent in chamber 1. Maximum load: 5.0 kg Delicate washing programmes A 30, 40, 60 C for delicate artificial synthetic fibres, blends or linen fabrics. They prevent the formation of creases that are difficult to remove during ironing. Maximum load: 2.5 kg Reduced spin speed Wool and Silk washing programme U 15, 30 C Delicates cycle only for garments marked pure wool" washable, treated, shrink proof and machine washa ble silk. We do not recommend washing these textiles with other rougher textiles.

Other types of wool should be hand washed or dry cleaned. Maximum load: 1.0 kg Reduced spin speed

Drying programmes

Y dry Resistant fabric white and coloured cottons and linens Load: 1.5 to 2.5 kg Drying time: 40 to 90 minutes Z delicate Delicate fabric Easycare (dripdry) laundry, such as synthetics and fabric blends, as well as cotton with dripdry finish, e.g. viscose rayon, cuprammonium rayon, modacrylic fibre and polyester Load: 1.5 to 2.5 kg Drying time: 70 to 120 minutes i To spin warm laundry is more effective than cold one. Therefore there is a special spin cycle integrated in the drying programme. Select the spin speed with the B spin button before starting the drying programme. The spin option is only possible for the Y dry pro gramme and for drying times ranging from 1 h 30 min to 2 h 0 min. We recommend the special spin cycle for resistant cotton, coloured or hemp fabrics.

Special programmes

Softener For an additional rinse cycle turn the programme selector to K rinse. It ends with a short, gentle spin at 900 r.p.m. If the laundry is to be removed dripping wet, set the spin speed to 000 prior to starting this programme. For use fabric softener or starch fill the additives in dispenser 2 (3) before starting the programme. Softening q Fill the softener agent in dispenser 2 (3). q Set programme selector to K rinse. q Press the M start button. Starching For cotton and linen items. Do not use fabric conditioner before starching. q Dissolve starching agent in water. Follow the ma nufacturer's instructions on the package. q Fill the starch in dispenser 2 (3). q Set programme selector to K rinse. q Press the M start button. If the laundry is to be dried in the washer dryer subse quent to the starching cycle, add approx. 30 to 50 % more starch, and select the empty b + spin B pro gramme with the maximum spin speed to attain the highest degree of water extraction.
Soaking Only put items of the same colour into the drum. Put detergent for soaking in chamber 1. Follow the manufacturer's instructions on the package. i If the soaking suds are to be retained for the main wash programme, a detergent suitable for drum type washers must be used. (Risk of excessive foam formation!) Set programme selector to A easycare 30 or 40. Press the M start button. After approx. 15 minutes, set the programme selector to off and allow laundry to soak in suds as long as desired. i After one minute the loading door is unlocked. Suds may exit when opening! To end the soaking programme: - Select spin speed suitable for your fabric. To avoid heavy foaming choose a wash programme with prewash after the spin cycle but do not put any detergent into compartment 1. - If the laundry is to be washed in the soaking water: Set the programme selector to the desired pro gramme and start it without adding further deter gent. Starting a wash programme automatically after soaking You can utilise the delayed start time function to effect the automatic termination of the soaking cycle. q Dependent upon the fabrics being washed, choose a wash programme with prewash, but do not fill any detergent into chamber 1 of the soap dispenser. q Use the W delay button to set the desired soak time.

Changing the drying programme
The drying programme changes by pressing the Y dry button once more after reaching the maximum of 2 hours or by pressing the Y dry button for about 4 seconds. To prevent overdrying of laundry which would cause it to shrink or crinkle, avoid selecting excessively long drying times. In addition, overdrying would consume energy unnecessarily. i Warm laundry appears more damp to the touch than cold laundry. This can easily lead to misjud gements.

Indicative drying times

Weight of washing 1.5 kg 2.5 kg
Resistant fabric 40 minutes 70 minutes 70 minutes 90 minutes
Delicate fabric 70 minutes 100 minutes 120 minutes -
Drying result Damp for ironing Dry Damp for ironing Dry

B spin button

Press this button to select the choice of the spin speed. q Press the button repeatedly to select the required spin speed. The following spin speeds are available: 000 rpm: Spin disabled and stop with tub full. The washer dryer does not perform the final spin and ends the washing programme with water in the tub. To drain the water, page 27. For cotton and coloured programmes, speed decreases by 100 rpm starting from max. 1600 down to 600 rpm For synthetics, delicates and woollens programmes, speed decreases by 100 rpm starting from 900 down to 600 rpm. The indicator LED lights up while the spin speed is being selected. If the option LED lights, the display indicates the selected spin speed. i Drying times depend on the spin speed: the higher the speed the lower the drying time and, conse quently, the lower the power consumption. Choo se the highest spin speed compatible with the type of laundry.

from 600 to 1600 rpm:

from 600 to 900 rpm:
Unbalanced load detection system
The automatic unbalanced load detection system turns round the laundry several times to ensure even distribution. If the laundry is very unevenly distributed, the final speed is reduced or there is no spin cycle for reasons of safety.

Washing and drying

This washer dryer allows - washonly - dryonly - wash+dry programmes to be set. In the wash+dry programmes, the cycle shifts auto matically from washing to drying without having to touch the controls to continue the cycle after washing. Opening the door Loading the washer dryer q Press the h door button to open the door. d Risk of explosion! Laundry items which have been pretreated with deter gents containing solvents, e.g. stain remover or clea ner's solvent, must be rinsed out thoroughly by hand before they are placed in the washer dryer, otherwise there is a risk of explosion! Warning Before loading the washer dryer, ensure that no foreign matter or pets are in the drum. q Place the laundry loosely and unfolded in the drum. Mix large and small items. q Please observe the maximum drum loads for the different wash and drying programmes, pages 23 and 24. q Ensure that no items of laundry are jammed between the door and the rubber seal. q Close the door by pressing it shut until it engages audibly. q Measure and fill detergent for washonly or wash+dry programmes. q Open the water tap.

Cleaning and servicing the washer dryer
d Risk of electric shock! First, always disconnect the appliance from the power supply. Never clean the washer dryer with a water jet. d Risk of explosion! Never clean the washer dryer with solvents. Warning Use only mild detergents to clean the washer dryer. Never use sharp objects they will damage the surface! If required: q Use a mild, nonabrasive detergent. q Wipe dry with a soft cloth. If metal items (e.g. coins, paper clips, needles, nails) left in the drum have caused rust spots: q Use chlorinefree cleaning agents; comply with the manufacturer's instructions. Never use steel wool.

Housing and fascia Drum

Detergent drawer
If there are detergent or cleaning product residues in the detergent drawer: q Pull out the detergent drawer to its stop (position). q Lift it slightly and q then pull fairly vigorously. q Clean the inside of the detergent drawer housing. q Remove the trap B. q Clean the detergent drawer and insert B under running water and dry. q Put back the trap B. q Slide in the detergent drawer.
If the water has not completely drained, foreign ob jects or fluff may block the pump. d Risk of scalding! Allow the hot water to cool down beforehand. Keep children and pets away from the washer dryer. q Switch off the washer dryer.

Open the service flap

Depending on the model, proceed as follows: Builtin appliance q Use a coin to turn the plastic buttons fixing the co ver to the base plate anticlockwise. Stand alone appliance q Insert a small screwdriver into the slots in the base plate cover then gently prise up to release the up per part of the cover. q Pull the cover slightly forwards and then up to re move it completely.

Drain the water

q Take the drainage hose out of the holder and pull out of the housing. q Place a tray on the floor and remove the plug B to drain the water. i Depending on the quantity of water, it may be ne cessary to empty the tray several times. q If there isn't any water, put in the plug B carefully and push the hose back in.
q Unscrew the cover of the pump D by turning it anticlockwise. A little more residual water will flow out. q Remove detergent residue, foreign objects and fluff from inside and clean the interior. The pump impeller wheel must be able to rotate. q Remove detergent residue and fluff from the pump cover thread and pump housing. q Insert the pump cover and screw tight. Insert and close the service flap Depending on the model, proceed as follows: Builtin appliance q Insert the lower part of the cover first. Then use a coin to secure it by turning the plastic buttons a quarter turn clockwise. i The slots in the buttons must be horizontal. Stand alone appliance q Insert the lower part of the cover first and then push it towards the housing until it clicks into pla ce.

Filter in the water inlet hose
If no water or insufficient water is running into the washer dryer: First, reduce the water pressure in the inlet hose: q Turn off the tap. q Switch off the washer dryer. q Remove the plug from the socket. q Remove the hose from the tap. q Clean the filter with a small brush or paint brush. q Connect the hose. q Open the water tap. q Check whether water is leaking out of the end of the hose connected to the tap. If water is still discharged, check that the strainer is attached properly.
Descaling the washer dryer
Caution Descaling agents contain acids which may corrode the components of the washer dryer and discolour the washing. Provided that you use the correct amount of detergent, it is not necessary to descale the washer dryer. If descaling is nevertheless required, please follow the instructions supplied by the manufacturer of the descaling agent.

What to do if.

d Risk of electric shock! Repairs may be carried out by customer service or authorised technicians only. If a repair is necessary or if you are unable to eliminate a fault yourself with the aid of the following table, pro ceed as follows: q Switch off the washer dryer. q Disconnect the machine from the power supply. q Turn off the tap. q Call customer service, page 46. In the event of faults, the washer dryer will display an error code. Error code Possible cause
Door not closed properly. You added more laundry. The safety device of the door doesn't locked yet. Water loss in the washer dryer

Remedial action

Close it. Wait until the safety device is locked. Disconnect the machine from the electrical power supply. Close the water tap. Contact the nearest customer service. Check that: - the water tap is open - the water inlet filter is not clogged. Clean it, page 40. -the check eye at the safety device is red, change the hose Check that: -the drain hose is not twisted -the drain pump is not clogged. Clean it, page 27.

No water for washing.

The water does not drain.
Other codes are important for our customer service only. Note the error code exactly for telling the customer service.
Fault washer dryer door cannot be opened. p
Possible cause Spin speed = 0 selected. Programme is running and/or washer dryer door is locked for safety reasons.
Remedial action Select and start the empty b + spin B programme. Wait until programme ends.
Programme does not g start.
M start button not pressed. Delayed start time is set. Power failure. Delayed start time is deleted. The door isn't securely closed. The plug isn't correctly fitted in the socket.

Press the M start button. None. Washer dryer starts automati cally after running the delay time. Select a new delay time or start the programm immediately: Press the M start button. Close the door. Fit the plug correctly.
Spin speed cannot be selected. Maximum spin speed cannot be set. Detergent residue in the detergent drawer. g
Spin cycle is already running; the Always select speed before the spin speed cannot be changed during the cycle starts. spin cycle. Easy care or Woolen programm selected. Damp or lumpy detergent. If required, change the programm. Clean and dry the detergent drawer, page 38. Use the dosing aid for liquid detergent.
The tub does not fill with The plug isn't correctly fitted into the Fit the plug correctly. water socket The washer dryer fills with water and drains continuously Water not visible in the drum. Water runs out from pp under the appliance. The drain hose is too low Fit the drain hose correctly, page 53.
Not a fault. When certain programmes run, the water is below the visible area. Screw fitting of the inlet hose is leaking. Drainage hose is leaking. Tighten the screwfitting. Have Customer Service replace the drainage hose.
Fault Water doesn't drain. Foam comes out of the detergent drawer. g
Possible cause Drain hose is twisted Drain pump is clogged. Too much or wrong detergent.
Remedial action Correct the drain hose. Clean the drain pump, page 39. Reduce the detergent dosage for the next wash cycle. Take only detergent suitable for automatic machines.
Spin cycle actuated several times.
Not a fault. Unbalanced load detection system is attempting to compensate the imbalance by spinning the washing several times. Large laundry items have become entangled and are not evenly distributed in the drum. For safety reasons the highspeed spin cycle was automatically reduced. Soiling is greater than expected. Detergent was underdosed.
Always wash large and small items together.
The washing has not been spun correctly.
Washing result not satisfactory. y
Select a suitable programme or a programm with prewash. Dose detergent according to the manufacturer's instructions. Select K rinse immediately or change over to liquid detergent. Brush the washing after the drying.
Detergent residue on the washing.
Some phosphatefree detergents contain waterinsoluble residue which may appear as light stains on the washing.
Fault Grey residue on the washing. Unexpected programme termination. shown in the the display The display is dark.
Possible cause Soiling caused by ointment, grease or oil. M start button inadvertently pressed. no failure the programm state is shown Power failure.

Resistant drying d i

Installing, connecting and transporting the washer dryer
Please install and connect the washer dryer in accordance with the enclosed installation and assembly instructions. Be sure to read the information contained in this chapter!

Safety information

d Risk of injury! The washer dryer is very heavy. Lift with caution. Frozen hoses may tear/burst. Do not install the machi ne in an area where there is a risk of frost or outdoors. The washer dryer may be damaged. Do not turn the washer dryer upside down and do not place it on its side. Do not lift the washer dryer by its projecting parts (e.g. door). Check the washer dryer for damage caused during transportation. Do not connect the washer dryer if it has visible signs of damage. If in doubt, contact your local dealer. Remove and keep transit bolts, page 51. In addition to the instructions listed here, particular regulations issued by the relevant water and power utility companies may apply. If in doubt, have the appliance connected by an elec trician.

Standard accessories

Stand alone appliance Bag inside the drum: - Feet - Counternuts for feet - Covers for holes left by removing the transport bolts. - Separator for liquid detergent - Wrench
On the rear of the washer dryer: - Water drainage hose. - Water inlet hose - Mains cable with plug. Builtin appliance In addition to the stand alone appliance In the packaging of the washer dryer: - a door template. Inside the drum: - another bag contains utilities for the builtin instal lation, see the separate Installation and assembly instructions. Moisture in the drum is due to the final inspection which every washer dryer undergoes before it leaves the factory. Depending on the connection situation, the following part is also required: - 1 24-40 mm hose clip (specialist outlet) for con nection to a siphon. Useful tool Use a spirit level for aligning the washer dryer.

Dimensions

Stand alone appliance a = 596 mm b = 552 mm c = 850 mm
Builtin appliance There are different dimensions for builtin appliance. See the separate Installation and assembly instruc tion.
Removing the wooden basis
d Risk of damage! Do not overturn the washer dryer and do not lay it on its sides. q Place the white polystyrene corner pieces on the floor behind the washer dryer, as shown in the dia gram.
q Carefully place the washer dryer on its back on the corner pieces.
q Remove the four screws fixing the wooden base with the supplied wrench.
q Screw the 4 feet (supplied) onto the underside of the washer dryer with the relative lock nuts.
Transport protection devices

d Risk of damage! Before using the washer dryer for the first time, com pletely remove the transport protection devices on the rear. Store the transport protection devices for later trans port (moving house). q Loosen bolts with the 13mm spanner until they are freely movable in the bushes. q Remove complete transport protection devices (bolt with sleeve).
q Insert the covers to prevent splashes or water getting inside the washer dryer, or touching parts under voltage.

Installation area

Appliance stability is important so that the washer dryer does not wander" during the spin cycles. The installation area must be solid and even. Soft floor surfaces, such as carpets or surfaces with foam backing, are not suitable. If the washer dryer is to be installed on a wood joist ceiling: q If possible, place the washer dryer in a corner of the room. q Screw a waterresistant wooden board (at least 30 mm thick) to the floor. q Affix the feet of the washer dryer using holding brackets *.
If the washer dryer is to be placed on a pedestal: q Affix the feet of the washer dryer using holding brackets *. * Holding brackets (set) can be obtained from a specialist store or the Customer Service (order no. WX 9756).
Positioning and levelling
Level the washer dryer with the assistance of the four adjustable feet and a spirit level. All four feet must be firmly on the floor. The washing machine must not wobble. The locknuts on the front feet of the appliance must be screwed against the housing! q Loosen the counternut 1 using the wrench. q Adjust the height by means of turning the appliance foot 2. q Tighten the counternut; grip the foot and do not adjust the height.
Attention Loud noises, vibrations and wandering" may be due to incorrect alignment! For builtin installation See the separate Installation and assembly instruc tion.

Hose and cable lengths

Connection on left side

approx. 110 cm

approx.130cm

max. 90 cm

approx. 180cm min. 50 cm

Connection on right side

approx. 100 cm
Aquasecure extension hose
Available in kit form from specialist outlets: - Connecting kit plastic hose (approx. 2.50 m), order no. WZ 10130. There are different hose and cable lenghts in builtin appliances. See the separate Installation and assem bly instruction.

For builtin installation

min. 50 cm

approx. 130 cm

Water connection
To prevent leaks or water damage, it is essential to follow the instructions in this chapter! Caution Operate the washer dryer with cold drinking water only. Do not connect the appliance to the mixer tap of an unpressurized hotwater boiler. If in any doubt, have the water connection carried out by an authorized technician. The water supply hose must not be: - Bent or squashed. - Modified or cut through (stability can no longer be guaranteed). Plastic threads must only be tightened by hand. Do not remove the strainers from the water supply hose. Observe the water pressure in the supply network: - The water pressure should be between 0.5x105. 9x105 Pa (0.5. 9 bars) (when the tap is turned on, at least 8 litres of water is discharged per minute). - A pressure reducing valve must be installed if the maximum water pressure is exceeded. Connect the water supply hose. q Connect the water supply hose to the tap. i The check eye 1 will be red, if the aquasecure hose (water inlet hose) is damaged, errorcode page 42. After connecting the water inlet hose: q Turn on the tap fully. q Check the connection points for leaks.

Care labels, 16 Cleaning and care Descaling, 41 Detergent drawer, 38 Drum, 38 Filter in the water inlet hose, 40 Housing and fascia, 38 Pump, 39 Connecting kit, 53 Consumption data, 46 Control panel, 10 Cottons/coloureds, 23 Customer service, 46
Degrees of dirt, 14 Delay Start, 10, 11, 28 Delicate drying, 25 Detergent, 19 Detergent drawer, 21, 38 Dimensions, 49 Display panel, 10 Door, 11 Door button, 10 Door template, 49 Dosing detergent, 19 Drain the water, 39 Dryonly programmes, 34 Drying button, 10, 30 Drying programmes, 24 Drying times, 30 Dyeing, 27
Laundry preparing, 13 remove, 13 sorting, 14, 17 Liquid detergent, 20 Low heat, 10
Maximum laundry loads, 16, 17 Normal heat, 10
Option lights, 10 W delay, 10 Z delicate, 10, 30 Y dry, 10, 30 B spin, 10 X end, 10
Easycare, 23 Electrical connection, 56 End, 10 End of programme, Without final spin, 37 Error code, 42
Fault, 42 Filling detergent, 21 Filter in the water inlet hose, 40 First wash, 22 Functions, 23
Positioning and levelling, 52 Powder detergent, 20 Programme selector, 10, 23 Programme state, 12 Programmes, 23 Dryonly , 34 Wash + Dry , 36 Washonly , 33 Pump, 39 Pumping, 27
Remedial action, 43 Removing stains, 15
Hose and cable lengths, 53 Identificationplate, 46
Scaleremovers, 21 Selecting Programmes, 23 Service flap, 39, 40 Short Wash, 10, 28 Signal, 11 Soaking, 26 Softener, 25 Special programmes, 25 Bleaching, 27 Dyeing, 27 Pumping, 27 Soaking, 26 Softening, 25 Starching, 25 Spin Speed,10, 12, 31 Stand alone appliance, 47 Standard accessories, 47 Starching, 25 Start, 10, 28
Time to end, 10 Transport protection devices, 52 Transporting the washer dryer, 56
Unbalanced load detection system, 31 Use, 32, 37
Wash + Dry programmes, 36 Washonly programmes, 33 Washer dryer, 11 Washing programmes, 23 Water connection, 54 Water drainage, 55 Water hardness, 19 Without final spin, 37 Wooden basis, 50 Woollens, 23

WDI1440/WDen 1108 00

TECHNICAL SPECIFICATIONS- EL POLO APARTMENTS SOTOGRANDE

IV PHASE

FOUNDATION AND FRAME: reinforced concrete pad using 250 Kg/cm2 concrete of resistance and wrought increasing the acoustic isolation between floors. ENCLOSURE AND BRICKWORK: Outside: ceramic brick wall composed leaf, muddy with concrete mortar, polyurethane cavity insulation 50 kg/cm2, air chamber and wall. Houses separated by acoustic insulation, with plate DANAFON, fixed with mechanical clamp over muddy of concrete mortar. Interior ceramic partition walls with double hollow brick. INSIDE CARPENTRY: solid panelled security entrance door with exterior NUEVO DUELAS system, fitted with security lock with TESA TBL anchorage points and anti-lever hinges. It is panelled in green for the exterior side, and in white colour inside. MAHOGONI-MERANTI wood with LASUR white glaze. System of anti-noise, brown colour ROVER PLASTIK bands. Crank of 250 OLV, model LORENA DE MARTINELLI. model STRIBO and wide-angle lens peephole. CARR FURNITURE Interior doors are panelled finished in MAPLE COAC colour. In the kitchen and in the living room with glasses, model CUADRAT-4. And in bedrooms and bathrooms model CADRE-4 with fittings of design. Wardrobes lined with lacquered ivory planks , with shelves and hanging rail. Doors model FLAT ABATIBLES, with the same colour than the interior doors and with hinges of 110 grades of opening and automatic return system. OUTSIDE CARPENTRY: Aluminium TECHNAL model SAPHIR carpentry, with fittings and lever of the same trade, even treatments with sea atmospheres of green granulated colour. In dinning rooms, elevated opening system and security glass. Mallorca-style exterior shutters in aluminium in bedrooms, the same colour as the carpentry. Climalit type glazing, with security glass in dinning room and Argon gas in the chamber. In pergolas and balustrade with pine wood and glazed treatment. PAVING AND FLOOR COVERING: Common areas and stairs in Breda gres with format 0.33X0.33 mts. In halls, bedrooms and living-rooms: macael white marble polished, format 0.40x0.40 mts. Kitchens: macael white marble and stuccoed fittings. The terraces with gres tiles, with a floating system to keep all the paving to the same level. The bathroom have an own designed, and comprises of marble and colour stucco. Outside filled with mortar water repellent and acriton paint or similar. Plates anti-impact under the flooring to increase the acoustic insulation. ROOF: Waterproofing and thermal insulation using polyurethane according to being walked or not.
AIR CONDITIONING: Hot and cold equipment super multi inverter sistem, Daikin with allows independent airconditioning by conduit machine and individual thermostat for each room. Use of ecologic refrigeration R410A, and type A of maximum rate of energetic effectiveness. Exterior machine MXZ-8A140V. Interior machines: Livings room with system for conduct, model SEZ-KA50VA, sonorous level 25 dB. Main bedroom: model MSZ-FA35VA with plasma filter and i-see Sensor system, automatic detection of heat centre, sonorous level 21 dB. In the rest of the rooms : model MSZ-GA35VA with CATECHIN filter for purification of air and sonorous level 21 dB. PLUMBING: hot and cold water distribution system with thermally insulated copper piping through and water-drainages of P.V.C sanitary. Hot water supplied by instant electrical heaters, model STIEBEL DHE-18, with remote control STIEBEL FB-1 controlling the temperature. ROCA fittings, DAMA SENSO COMPACTO model, with GROHE mixer tap or similar.

ELECTRICITY: triphase installation with an independent diferential protection system for the air conditioning, outside and in the rest of the house. Power point and perimeter lighting of terraces. Mechanisms NIESSEN model ARCO. TELECOMMUNICATIONS: System of reception of TV terrestrial signal. Satellite signal with centralised reception for the whole houses. Connexion for all the rooms and main terraces. Via Satellite channels opened directly in sockets, cable TV/broad band pre-installation in all the rooms. Telephone connection in living-room, bedroom, kitchen and main terraces. Electronic entry-phone with audio unit model NOVA NC221. Installation for the reception of Sky-digital, Canal Satellite digital and TV digital terrestrial. KITCHEN: fully fitted kitchen, model SERIE ALPINA from SANTOS. It composed by: Kitchen type A: Compensation over the refrigerator. Furniture for oven and microwave. A short piece of furniture with 1 drawer and 2 pull out drawer. Cutlery box in beech tree wood Door for the wash machine A short piece of furniture with 2 pulls out drawer stand for the sink An ecological rubbish bin Door for the dishwasher A hanging piece of furniture for display cabinet Costado visto alto Skirting board Worktops band f white silestone Bands of upper-crust with 15 cm high in white silestone Handles Ceramic hobSIEMENS MOD. ET72Q001E Dishwasher SIEMENS mod. SE65E331EU integrable Refrigerator SIEMENS mod. KG39S350 INOX. Oven SIEMENS mod. HB420540E Washing-dryer machine SIEMENS mod. WDI1440EE integrable. Microwave SIEMENS mod. HF17056 INOX Extractor hood FRECAM mod. TOP LINE 90 INOX Sink FRECAM mod.1611 INOX Tap FRECAM mod: PAR Cromo. Kitchen type C Compensation over the refrigerator. Furniture for oven and microwave. A piece of furniture in column size for keeping cleaning staff. A short piece of furniture with 1 drawer and 2 pull out drawer. A short piece of furniture with 1 drawer and 2 pull out drawer. Cutlery box in beech tree wood Door for the wash machine A short false corner 15x15 A short piece of furniture with 2 pulls out drawer stand for the sink An ecological rubbish bin Door for the dishwasher A hanging piece of furniture for storage Skirting board Worktops band f white silestone
Bands of upper-crust with 15 cm high in white silestone marble. Stainless steal handles in bar shape. Ceramic hobSIEMENS MOD. ET72Q001E Dishwasher SIEMENS mod. SE65E331EU integrable Refrigerator SIEMENS mod. KG39S350 INOX. Oven SIEMENS mod. HB420540E Washing-dryer machine SIEMENS mod. WDI1440EE integrable. Microwave SIEMENS mod. HF17056 INOX Extractor hood FRECAM mod. TOP LINE 90 INOX Sink FRECAM mod.1611 INOX Tap FRECAM mod: PAR Cromo. In both types of kitchens, the oven and the microwave can be replaced by a compact oven plus INNOWAVE steel microwave from SIEMENS mod. HB84K550.

LIFTS: Electronic luxury cabins of MACPUAR, S.A. Without machines room. For 6 person. With access to the basement. Double boarding of 180 grades in the ground floor. Access for the handicapped. Automatic doors with stainless steal finish and they are fire resistant for 30 minutes. SECURITY: security sistem centralized in the main access of the urbanisation by closed circuit TV with control of the perimeter of the urbanisation. Basements and pier access. SEGURITAS DIRECT. Direct communication with guard house. BASEMENT: spacious storages for each house. Protection against fire. Wide access way. Power point in storages. COMMON AREA: Community club with common garden areas, swimming pool, sauna, toilets, dressing rooms. A wooden pier for small boats. The houses are given with a maintenance manual, provider list and decenal insurance. Iridium alarm of

www.elpolo.es

This is the final technical specifications for this development under construction nowadays. According to the second phase, we take this one like a model, although is subjected to possible modifications.