INTELLIKNIGHT FIRE ALARM CONTROL PANEL
The IntelliKnight System is the easy way to make the most of fire alarm technology.
IntelliKnight 5820XL is the first fire alarm system to provide you with revolutionary value and performance in addressable sensing technology. The 5820XL FACP offers exclusive, built-in digital communication, distributed intelligent power, a modular design and an expanded, easy to use interface. Powerful features such as drift compensation and maintenance alert are delivered in this powerful FACP from Silent Knight. For more information about the 5820XL system, or to locate your nearest source, please call 800-328-0103. Description
5820XL is an intelligent addressable fire alarm control panel (FACP). The basic 5820XL system can be expanded by adding modules such as 5860 remote annunciator, 5815XL signalling line circuit expander, 5824 serial/parallel printer interface module (for printing system reports), and 5895XL intelligent power module. 5820XL supports Hochiki or SK devices. 5820XL also features a powerful built-in dual line fire communicator that allows for reporting of all system activity to a remote monitoring location.
IntelliKnight Model 5820XL Addressable Fire Alarm Control System

Features

Built in support for 99 SK detectors and 99 SK modules, expandable to 396 SK detectors and 396 SK modules using System Sensor protocol Built in support for 127 Hochiki devices, expandable to 508 Hochiki devices using Hochiki protocol. Uses standard wireno shielded or twisted pair required Built-in digital communicator Central station reporting by point or by zone Built-in synchronization for appliances from AMSECO, Gentex, Faraday, System Sensor, and Wheelock Flexput I/O circuits Supports Class B (Style 4) and Class A (Style 6) configuration for SLC, SBUS, and Flexput circuits Distributed, intelligent power Drift compensation 13 pre-programmed output cadences (including ANSI-3.41) and 4 programmable outputs Built-in annunciator with 80-character LCD display RS-485 bus provides communication to system accessories Built-in RS-232 and USB interface for programming via PC Built-in Form C trouble relay rated at 2.5 amps at 27.4 VDC Improvements in SKSS software deliver five times faster uploads/downloads Two built-in Form C programmable relays rated at 2.5 amps at 27.4 VDC Supports sounder bases 6 amp power supply and maximum charging capacity of 35 amp hours (An additional cabinet enclosure is required for batteries in excess of 18 amp hours) Programmable date setting for Daylight Saving Time Plex-1 door option combines a dead front cabinet door with a clear window, limiting access to the panel while providing single button operation of the reset and silence functions

Installation

Model 5820XL
The 5820XL can be surface or flush mounted

Compatibility

The 5820XL SLC supports multiple device types of the same protocol: SK (System Sensor) Hochiki You cannot mix Hochiki and SK devices on a FACP.
IntelliKnight Model 5820XL Addressable Fire Alarm Control Panel

Indicator Lights

5820XL features a 6 amp power supply and maximum battery charging capacity of 35 amp hours. An additional cabinet enclosure (PN RBB) is required for batteries in excess of 18 amp hours. Flexput circuits on 5820XL control can be individually programmed to function as notification circuits, auxiliary power outputs, or initiation circuits that support both 2- and 4-wire smoke detectors. The 5820XL system operates on nontwisted, unshielded cable when wired in compliance with standard wiring practices as called out in the National Electric Code 760-51 specifications for power-limited fire protective signalling cables. No special wiring is required. 5820XL provides 13 preset notification cadence patterns (including ANSI 3.41) and four user programmable selections for fire alarm notification. Two programmable general purpose Form C relay outputs are provided on 5820XL. Additionally, the IntelliKnight system features a built-in walk test and autoprogramming. Its innovative, dead-front cabinet design allows for flush or surface mounting. System maintenance is easy to perform. required to start a new system. The built-in keypad and 5860 remote annunciator give on-site access to all programming. You can also program remotely using the 5660 Silent Knight Software Suite, which is Windowsbased software.
General Alarm (Red): Flashes when in alarm; solid when alarm silenced
Supervisory (Yellow): Flashes when a supervisory condition exists; solid when supervisory silenced System Troubles (Yellow): Flashes when a trouble condition exists; solid when trouble silenced
System Silenced (Yellow): On when an alarm, trouble or supervisory condition has been silenced but not yet cleared

Built-In Digital Communicator
System Power (Green): Flashes for AC failure; solid when power systems are normal

System Application

5820XL has one built-in signalling line circuit (SLC) which supports multiple devices dependent on protocol being used. Three additional loops can be added using the 5815XL SLC expanders to increase overall capacity. The 5820XL SLC loops support multiple device types, including: Addressable photoelectric smoke detector Addressable ionization smoke detector Addressable heat sensor Contact module Relay output module
5820XL features a built-in UL listed digital communicator for remote reporting of system activity and system programming. The communicator has the ability to seize two telephone lines to report alarms and troubles to a monitoring facility. The communicator supervises two phone lines and will activate a trouble signal if a line failure is sustained for more than 45 seconds. Other communication features include: retry if communication fails, two phone number capability, download phone number capability and Touch-Tone or rotary dialing. The communicator is compatible with SIA and Ademco Contact ID. The format is selectable by account number.
Addressable duct smoke detector Addressable notification module

User Interface

Addressable beam detector (SK protocol only) Addressable multi modules (SK protocol only) Automatic drift compensation Maintenance alert
Addressable multi-criteria smoke detector (SK protocol only) The following advanced sensor capabilities are available with 5820XL: Built-in sensor test to comply with NFPA 72 calibration testing requirements
The 5820XL built-in annunciator with 80 character LCD display and large easy-to-use tactile touchpad can be used for system operation, programming and maintenance. It has five LEDs for alarm, supervisory, system trouble, system silenced and system power. System operations include silencing alarms and troubles, resetting alarms and the display of alarm troubles and memory. The system's non-volatile event history buffer stores 1000 events for viewing from the built-in or remote annunciator. System operation can be initiated with a mechanical firefighter's key or a valid 4- to 7-digit operator's code. The IntelliKnight system offers several options to simplify and speed up programming. The JumpStart feature minimizes programming

Approvals

Programming
NFPA 13, NFPA 15, NFPA 16, NFPA 72: Central Station; Remote Signalling; Local Protective Signalling Systems; Auxiliary Protected Premises Unit; & Water Deluge Releasing Service. Suitable for automatic, manual, waterflow, sprinkler supervisory (DACT non-coded) signalling services. Other Approvals: UL Listed; CSFM 7170-0559: 135; MEA 429-92-E Vol. VI; FM Approved
Specifications Electrical S-BUS Accessories Miscellaneous Accessories
Primary AC: 120 VRMS at 50/60 Hz, 2.5A or 240 VRMS at 50/60 Hz, 1.4A Total Accessory Load: 6A @ 27.4 VDC, power-limited Standby Current: 215 mA Alarm Current: 385 mA Flexput Circuits: Six programmable circuits which can be programmed individually as: Notification circuits: 3A @ 27.4 VDC per circuit, power-limited Auxiliary power circuits: 3A @ 27.4VDC per circuit, power-limited Initiation Circuits: 100 mA @ 27.4VDC per circuit, power limited
5860/R Remote Fire Annunciator Features the same 80 character backlit LCD display keypad and firefighter's keyswitch as the 5820XL. 5860 is gray and 5860R is red.
5815XL Signal Line Circuit Expander The SLC expander is used to add more addressable devices to the IntelliKnight system. 5820XL supports three 5815XLs. Each 5815XL can support 127 devices. 5895XL Intelligent Power Module Adds 6 amps of power, 6 Flexput I/O circuits and 2 Form C relay circuits to a 5820XL system.
5660 Silent Knight Software Suite (SKSS) User-friendly Windows software for remote programming of 5820XLs using a PC. Upload and view panel account information, event history, and detector status. 5670 Silent Knight Software Suite (SKSS) Powerful end-user facility management software allows viewing of detector status and event history via modem or direct connection. Plex-1 Dead front cabinet door with clear window to limit access to the FACP.

Physical

Flush Mount Dimensions: 14.5W x 24.75H x 3.9D (36.8 W x 62.9 H x 9.8 D cm ) Overall Dimensions: 16.2W x 26.4H x 4.2D (40.6 W x 67 H x 11.8 D cm) Weight: 28 lbs. (12.8 kg) Color: Red
5880 LED/IO Module Features 40 LED outputs, 8 normally open dry contact inputs, and one piezo output.
5496 Intelligent Power Module A 6 amp notification power expander that provides four power-limited notification appliance circuit outputs.

RBB Remote battery box accessory cabinet. Use if backup batteries are too large to fit into FACP cabinet. Dimensions: 16 W x 10 H x 6 D (406 mm W x 254 mm H x 152 mm D)
5865-3 and 5865-4 Remote LED Annunciator Features 30 programmable LED (15 red and 15 yellow) outputs, and a piezo sounder. The 5865-4 adds a silence and reset switch to the package. 5883 Relay Board Features 10 general purpose Form C relays. Used with 5880 module.
SD505-DTS-K Remote test switch. Used with SD505-DUCTR. Provides remote key operated test function and annunciation of detector alarm.

Hochiki and SK Devices

Battery Charging Capacity: 7.0-35 AH Battery Size: 18 AH max allowed in control panel cabinet. Larger capacity batteries can be housed in RBB accessory cabinet. Telephone Requirements: FCC Part 15 and Part 68 approved Type of Jack: RJ31X (two required)
5824 Serial/Parallel Printer Interface Module Provides one parallel and one RS-232 serial port for connecting a printer to the 5820XL. Use to print a real-time log of system events, detector status reports, and event history. Interfaces with building control system.
See the specification sheets listed below for a complete listing of the Hochiki and SK devices. 53624 Hochiki Devices Data Sheet 53623 SK Device Protocol Devices Specification Sheet
This document is not intended to be used for installation purposes. We try to keep our product information up-to-date and accurate. We cannot cover all specific applications or anticipate all requirements. All specifications are subject to change without notice. For more information, contact Silent Knight 12 Clintonville Road, Northford, CT 06472 Phone: (203) 484-7161, Fax: (203) 484-7118. www.silentknight.com. IntelliKnight & JumpStart are Registered Trademarks of Silent Knight Flexput is a Trademark of Silent Knight

Made in America

PN 350210 Rev G 2010 Honeywell International Inc.

7.6.3.1 Assigning a Name to Points.... 7-27 System Options.... 7-27 7.7.1 Reporting Account.... 7-28 7.7.1.1 Edit Accounts.... 7-29 Select Account (ID).... 7-29 Edit Account Number.... 7-29 Select Reporting Format.... 7-29 Events to Report.... 7-30 Switch Attempts.... 7-30 Fail Attempts.... 7-30 Selecting Primary and Secondary Phone Lines.. 7-30 Telephone Number.... 7-31 7.7.1.2 Auto Test Time.... 7-32 7.7.2 Phone Lines..... 7-32 7.7.2.1 Dialing Prefix.... 7-33 7.7.2.2 Number of Answer Rings.... 7-34 7.7.2.3 Dial Option (TouchTone or Pulse).... 7-34 7.7.2.4 Rotary Format..... 7-34 7.7.2.5 Line Monitor.... 7-34 7.7.2.6 Ground Start Relay.... 7-34 7.7.2.7 Answering Machine Bypass.... 7-35 7.7.3 Sys. Event Outputs.... 7-35 7.7.3.1 Trouble Events.... 7-36 7.7.3.2 System Alarm Cadence.... 7-37 7.7.4 Miscellaneous Options 1..... 7-38 7.7.4.1 Water Flow Delay.... 7-38 7.7.4.2 Low AC Report Delay.... 7-40 7.7.4.3 Automatic Daylight Savings Adjustment... 7-40 7.7.4.4 Clock Display Format (AM/PM or Military)... 7-40 7.7.4.5 Change AC Line Frequency.... 7-40 7.7.5 Miscellaneous Options 2..... 7-41 7.7.5.1 Synchronize Strobes Active During Silence.. 7-41 7.7.5.2 Auto Display Oldest Event... 7-41 7.7.5.3 Report by Zone or by Point... 7-41 7.7.6 Miscellaneous Options 3..... 7-42 7.7.6.1 Alarm Verification Time.... 7-42 7.7.6.2 Plex Door Option..... 7-42 7.7.6.3 Daylight Saving Time Start and End... 7-43 7.7.7 Edit Banner Message..... 7-44 7.8 JumpStart Autoprogramming..... 7-45 7.9 Computer Account.... 7-46 7.7
7.10 Access Codes..... 7-47 7.10.1 Profile Edit Menu.... 7-48 7.10.1.1 Edit Name.... 7-48 7.10.1.2 Edit Access Code..... 7-48 7.10.1.3 Panel Functions.... 7-48
Section 8 System Operation

8.1 8.2

.... 8-1

8.3 8.4

8.6 8.7
User and Installer Default Codes.... 8-1 Annunciator Description.... 8-1 8.2.1 LCD Displays..... 8-2 8.2.2 Banner..... 8-2 Key Operation..... 8-2 Menu System..... 8-3 8.4.1 Main Menu Overview.... 8-3 8.4.2 Using the Menus.... 8-4 Basic Operation..... 8-4 8.5.1 Setting Time and Date..... 8-4 8.5.2 Disable / Enable a Point.... 8-4 8.5.3 Disable / Enable NACs by Group.... 8-4 8.5.4 View Event History.... 8-5 8.5.4.1 To clear the event history... 8-5 8.5.5 Conduct a Fire Drill.... 8-5 8.5.6 Conduct an Indicator Test..... 8-5 8.5.7 Conduct a Walk Test.... 8-6 8.5.8 Conduct a Dialer Test.... 8-6 8.5.9 Silence alarms or troubles..... 8-7 8.5.10 Reset alarms.... 8-7 8.5.11 Check Detector Through Point Status.... 8-7 8.5.12 View Status of a Point..... 8-8 8.5.13 View Alarms or Troubles..... 8-8 8.5.14 View System Information..... 8-8 8.5.15 Reset dialer..... 8-8 8.5.16 Communicating with a Remote Computer.... 8-9 8.5.17 Working with a Printer.... 8-10 Operation Mode Behavior..... 8-11 Releasing Operations..... 8-14 8.7.1 Single Interlock Zone Releasing.... 8-15 Conditions Required for an Pre-Alert Output Activation.. 8-15 Conditions required for an General Alarm and Release Output Activation. 8-15

2.1 Federal Communications Commission (FCC)
1. The following information must be provided to the telephone company before the IntelliKnight 5820XL can be connected to the phone lines:
A B C D E F Manufacturer: Model Number: FCC registration number: Ringer equivalence: Type of jack: Facility Interface Codes: Service Order Code: Silent Knight IntelliKnight 5820XL AC6USA-23901-AL-E 0.8B RJ31X Loop Start: 02LS2 Ground Start: 02GS2 9.0F
This equipment complies with Part 68 of the FCC rules and the requirements adopted by ACTA. On the inside cover of this equipment is a label that contains, among other information, a product identifier. If requested, this information must be provided to the telephone company. A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord (not provided) and modular jack must be utilized with this product. It is designed to be used with a modular jack that is also compliant. The REN (ringer equivalence number) provided on this installation sheet is used to determine the number of devices that may be connected to the public switched telephone network. This number must not exceed 5.0. Since this product has an REN of 1.0, the number of devices is limited. The REN number is imbedded in the FCC registration number as 10B. If the 5820XL causes harm to the telephone network, the telephone company will notify you in advance that the temporarily discontinuance of service may be required. But if advance notice is not practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary. The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service. If trouble is experienced with the 5820XL, for repair or warranty information, please contact Silent Knight at 1-800-328-0103 or www.silentknight.com. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the 5820XL until the problem has been resolved.

Mounting the 5860

This section of the manual describes mounting the remote annunciator. The annunciator can be flush- or surface-mounted. Figure 4-10 shows the parts of the annunciator. Instructions for disassembling and mounting appear on the following pages.
Figure 4-10 Annunciator Parts
The 5860 comes from the factory fully assembled. You must disassemble it for mounting. To disassemble the annunciator, use a 5/64 hex wrench to remove the set screws, located on the bottom of the annunciator bezel. (See Figure 4-11 for location of the set screws.)
Figure 4-11 Annunciator Back Box and Bezel Details

4.5.1.1 Flush Mounting

This section of the manual describes flush mounting. You can flush-mount with or without an electrical box.
Flush Mounting with an Electrical Box The 5860 annunciator can be used with the following types of electrical boxes: 4S, singlegang, and double-gang. If an electrical box is used, the box must be 1-3/8 back from the face of the wall to accommodate the annunciator. Studs used with an electrical box must be two by fours (or larger).
Figure 4-12 Placement of Electrical Box for Flush Mounting
Flush Mounting Steps 1. Cut a hole in the sheet rock to the following dimensions: 8-1/4 w x 6-5/8 h. If an electrical box is used, the box must be 1-3/8 back from face of wall to accommodate the annunciator (see Figure 4-12). 2. Remove knockout holes as needed for wires. 3. Fit the annunciator back box into the hole and stabilize with mounting wires. Angle the mounting wires into the first hole past the sheet rock. Secure the wires behind the screws as shown in Figure 4-13. When all four wires are in place, the back box should fit snugly into the hole in the sheet rock.
4. After the annunciator wiring to the panel has been completed (described in Section 4.5.2), replace the electronic assembly in the back box. Place the bezel over the back box and tighten the set screws on the bezel.
Figure 4-13 Flush Mounting the Back Box

4.5.1.2 Surface Mounting

The 5860 can be mounted directly to a surface or can be attached to a single, double, or foursquare electrical box. The Model 5860TG/TR trim ring kit is available for use when surface mounting. 1. Drill holes in the surface to match the screw holes on the back box. 2. Fit the trim ring over the back box. 3. Attach the back box to the surface using screws provided. 4. After the annunciator wiring to the panel has been completed (described in Section 4.5.2), replace the electronic assembly in the back box. Place the bezel over the back box and tighten the set screws on the bezel.

4.13.1.1 Regulated Class B Notification Wiring
You must use an appliance from the list of compatible appliances in the Appendix A at the back of this manual. To install a circuit: 1. Wire Class B Notification appliances as shown in Figure 4-30.
2. Configure the circuit through programming (see Section 7.6).
Alarm Polarity UL Listed EOL Model 7628 4.7 k Max. Impedance: 1.5 Regulated 24 VDC Full Wave Rectified 27.4 VDC, 3A per Circuit, 6A max Combined Notification Wiring Supervised Power Limited
Figure 4-30 Class B Notification Appliance Circuit Wiring
4.13.1.2 Class A Notification Wiring
You must use an appliance from the list of compatible appliances in the Appendix at the back of this manual. To install a Class A notification appliance circuit: 1. Wire the Class A notification appliances as shown in Figure 4-31.
For proper system supervision do not use looped wire under terminals marked O and X of the Flexput connectors. Break wire runs to provide supervision of connections.
2. Configure the circuit for Class A in programming (see Section 7.6).
Regulated 24 VDC Full Wave Rectified 27.4 VDC, 3A per Circuit, 6A max Combined
Figure 4-31 Class A Notification Appliance Circuit Configuration Note: In programming any point that uses multiple Flexput circuits, the lowest Flexput circuit number is used to refer to the circuit pair. For example, Figure 4-31 uses both Flexput circuit 5 and 6, so in programming it would be referred to as point 5.
4.13.2 Conventional Input Switch Circuits
This section of the manual explains how to install conventional initiating devices for Class A (Style D) or Class B (Style B) configurations.

4.13.2.1 Class B Inputs

You can connect conventional Class B switches, such as waterflow switches and pull stations, directly to the Flexput circuits of the control panel. To install a Class B switch: 1. Wire the Class B switch as shown in Figure 4-32. 2. Configure the circuit through programming (see Section 7.6).
Supervised Power Limited UL Listed EOL Model 7628 4.7 k

JumpStart Autoprogramming
The JumpStart feature allows for faster system setup. When you run JumpStart (immediately after addressing SLC devices), the system scans devices on all SLC loops and determines device type (for example, ionization smoke detector or heat sensor) and selects some system options based on the device type. This saves the installer from having to program options for each device. Depending on the application, the installer may need to make some changes after JumpStart completes. See Section 6.1.3 for complete details about running JumpStart.
IMPORTANT JumpStart is intended to be run one time only, immediately after SLC devices have been addressed and connected. JumpStart will reset all manually programmed options to default settings. Do not run JumpStart after you have configured the system.

Input Points

JumpStart will determine the number and type of input points (detectors or contact monitor modules) on each SLC loop. JumpStart assigns the correct detector type (heat, ionization or photoelectric), so the installer does not need to edit device type for detectors. Any contact monitor modules on the system will be assigned type "Manual Pull." The installer will need to manually change the switch type if manual pull is not correct. JumpStart creates one zone (Zone 1) and assigns all input points to Zone 1. Zone 1 is mapped to Output Group 1. After JumpStart completes, you can re-map to configure a multiple zone/ output group system (see Section 7.4.1.3). For a general explanation of mapping, see Section 6.2.

Output Points

JumpStart creates three output groups and assigns output circuits as follows: Circuits 1-6: Configured as Notification and assigned to Group 1. JumpStart automatically programs Zone 1 to activate Group 1 using constant on output. Circuit 7 (Relay 1): Assigned to Group 249. JumpStart automatically programs Zone 1 to activate Group 249 using constant on output when a supervisory condition occurs. Circuit 8 (Relay 2): Assigned to Group 250. JumpStart automatically programs Zone 1 to activate Group 250 using constant on output when an alarm occurs. Addressable output points (Relay modules, NAC Modules, Sounder Bases, Relay Bases): All addressable relay devices will be configured as Output Pt (general purpose output point) and assigned to Group 1.

Mapping Overview

This section of the manual is an overview of mapping. Details about how to select mapping options appear in the appropriate subsections in Section 7. Mapping is an important concept with the control panel. In general terms, mapping is assigning or linking events to outputs that should activate when events occur. You do this by assigning input points to input zones, output points to output groups and then linking or mapping zones and output groups. Figure 6-1 is a brief overview of the concept of mapping. The next several pages of the manual show these subjects in detail.
Figure 6-1 Mapping Overview

Input Point Mapping

Input points are assigned to input zones. Any input point can be assigned to any input zone. (Input points can be assigned to one zone only. An input point can be designated as Unused, which means it has not been assigned to a zone.)
Figure 6-2 Input Point Assignment Example

Output Circuit Mapping

Figure 6-3 is a simple example showing how to assign notification and relay output circuits to groups. For an example of a simple floor above/floor below application, see Figure 6-5.
Figure 6-3 Assigning Output Circuits to Groups (Example)

Zone Event Mapping

There are 8 types of events that can occur in zones (see below). For each event type, you can activate up to 8 output groups and patterns. If it is necessary to map to more than 8 output groups, an output group template may be used (see Section 7.5.5 for information on output group templates). Event types are: Manual Pull Alarm Water Flow Alarm Detector Alarm (heat or smoke detectors) Aux 1 and Aux 2 Alarm (user-specified alarm types) Pre-alarm Supervisory Trouble
Figure 6-4 Example of Zone Events Mapped to Output Groups and Patterns
Figure 6-5 Example of Zone Events Mapped to Output Groups and Patterns

Mapping LED Points

Figure 6-6 is a simple example showing how LED points are mapped to zones and output groups. Typically you would create two output groups for each zone, one for alarms and one for troubles. (LED points are available when Models 5865-3/4 and/or 5880 are used with the system.)

Group or Zone selection will appear depending on the type selected. Section 7.6 Enter Name NOTIF UNUSED Enter Name NOTIF UNUSED Enter Name Section 7.6.3
Edit Name Enter Point # 5880 Select Group # Edit Name Enter Point # 5865 Select Group # Edit Name

Section 7.6.3

Options/Defaults Edit Account # For each account (1-4), select: *123456
Comments Account # (6-digit number, identifies account to central station) Section 7.7.1 Reporting Format (SIA, S20, Contact ID) Section 7.7.1 Section 7.7.1

Edit Format

*Contact ID
Edit Acct. System Options Reporting Accounts

Auto Test Time

Y (Yes) N (No) M (Must) Y (Yes) Rep. Alarm Restore N (No) M (Must) Y (Yes) Report Troubles N (No) M (Must) Y (Yes) Report Ena/Disable N (No) M (Must) Y (Yes) Report Test N (No) M (Must) Y (Yes) Report Resets N (No) M (Must) Switch attempts 1-5 Fail attempts 1 - 15 Primary Phone Line 1 or 2 Secondary Phone 1 or 2 Line Edit Phone #1 up to 40 digits Set the Hour Set the Minutes Select AM/PM Report Alarms
*5 *10 *Line 1 *Line 2 blank *02:00 AM

Section 7.7.1

Options/Defaults For each phone line (1 & 2), select: Dialing Prefix Up to 9 digits # of Answer Rings Range: 00-15 none 06
Comments Section 7.7.2.1 Number of rings before panel answers a call from a computer Section 7.7.2.2 Touch Tone TouchTone alternating with pulse see Section 7.7.2.3 Pulse dialing Section 7.7.2.4 Section 7.7.2.5 Section 7.7.2.6 Section 7.7.2.7 Section 7.7.3.1
TT TT/PL Select Dialing Option Phone Lines Select Phone Line PULSE U = 60/40 Rotary Pulse Format E = 66/34 Yes Line Monitor No Yes = enabled Ground Start No = disabled Answering Machine Yes = enabled Bypass No = disabled Select Group System Trouble Select Cadence Alarm Silence Select Group Select Cadence Select Group Trbl Silence Select Cadence Group Tr SBUS Com SBUS Pwr Trouble Events SLC Loop AC Loss Battery User Selected Gnd Flt Phone Ln Account Printer Aux Pwr Sys Sw Fire Drill Select Cadence Sys Alarm Cadence System Aux1 System Aux2 TouchTone

*U *Yes

*N = Disabled *Y = Enabled None selected None selected None selected

System Options (cont.)

Select Group

System Event Outputs

Select Cadence

Section 7.7.3.2 Constant

Options/Defaults 0 - 90 Seconds Water Flow Delay *30 sec
Comments Water Flow delay is the number of sec. before water flow alarm is generated. Section 7.7.4.1 Low AC Report Delay. Section 7.7.4.2 Automatic Daylight Saving Time enable or disable. Section 7.7.4.3 and 7.7.6.3. See also DST settings in Misc. Option 3, below. System Clock Format (AM/PM or military). Section 7.7.4.4 Section 7.7.4.5

arrow.

2-Count

Alarm Ver.

SNGL ILOCK DBL ILOCK

4. Press

Heat Temperature Setting Use this feature to set the temperature at which heat detectors will respond. The range is 135 to 150 F. All detectors in the zone will respond in the same way. The Model SD505-AHS Heat Detector is an absolute temperature device. This means that it responds to an alarm immediately if the temperature in the zone goes above the programmed temperature. 5. Enter the temperature at which the heat detector will respond. Or Use the or keys to scroll through the range or enter directly from the number keys. on the annunciator, then press
6. Use the or keys to scroll through the range or enter directly from the number keys on the annunciator.

7. Then press

7.4.1.3 Zone Outputs
Output groups and cadence patterns are mapped to events. They can be programmed to output when an event occurs in a zone. Some system trouble events can be mapped for the entire system. Section 6.2 of this manual contains a general explanation of mapping. The following sections explain how to select mapping options.
Note: Use of multiple notification groups may not synchronize with each other.
Mapping to Zone Events Eight types of events can occur in zones. For each event type, you can activate up to 8 output groups or output group template, specifying a pattern for each. The following is a list of all event types:
Note: Abbreviations in the parenthesizes are the characters that are displayed in programming (see Figure 7-3).
Manual Pull Alarm (MP) Water Flow Alarm (WF) Detector Alarm (DE). This applies to heat or smoke detectors. Aux 1 and Aux 2 Alarm (A1 or A2). User-specified alarm types. Pre-alarm (PR) Supervisory (SU) Trouble (TR) for Program Menu.
To map zone events to outputs: 1. From the Installer Main Menu, select 2. From the Program Menu, select 3. From the next menu, select

for Zone.

for Edit Zone.
4. Enter the zone number you wish to edit. 5. From the next menu, select

for Zone Outputs.

6. From the next screen, a list of 8 event types will display. Select the event type you want to program. A screen similar to the one shown in Figure 7-3 will display. Press 7. Press the or

MAN_PULL Latching

WATERFLOW

Non Latching

Latching SUPERVISY SWITCH FIREDRILL Non Latching

SILENCE

Type Selection Function ZN_AUX1 ZN_AUX2 SYS_AUX1 SYS_AUX2 DETECT SW TAMPER MAN REL ILOCK OUTPUT PT AUX CONST NOTIF AUX RESET AUX DOOR OUTPUT PT RELAY AUX RESET AUX DOOR Select Group Select Group Select Group Latching Non Latching Latching Non Latching Latching Non Latching Select Group Latching Option Latching Non Latching Latching Non Latching Latching Non Latching Latching Non Latching Comments Use these switch types if you want to monitor special zone-level conditions (such as operation of a fan or damper).
Use these switch types if you want to monitor special system-wide conditions (such as operation of a fan or damper).

SWITCH (cont.)

Used to monitor conventional 4-wire detectors, a contact closure will generate a detector alarm event. Performs identically to a supervisory switch, but will be indicated as a tamper switch on the LCD annunciator. Manual release switch, typically a pull station. Interlock release switch input. Output Point, a general use notification type. Use for driving standard notification appliances. Use constant power for applications that require a constant auxiliary power source. Power is always present at Constant circuits. Use for auxiliary power, resettable applications. See Section 4.13.5.3 for a description of how this option operates. Use for auxiliary power, door holder applications. For example, if you were using an auxiliary power supply for door holders, you would use this option. See Section 4.13.5.1 for a description of how this option operates. Output Point, a general use relay type. Use for applications requiring a relay, such as fan shutdown, elevator recall, and so on. Use for auxiliary power, resettable applications. See Section 4.13.5.3 for a description of how this option operates. Use for auxiliary power, door holder applications. For example, if you were using an auxiliary power supply for door holders, you would use this option. See Section 4.13.5.1 for a description of how this option operates.
Programming Table 7-5: Point Programming Options for 5815XL Modules
Type Selection SLC LED Function Latching Option Comments
Select LED No. Select Group 01 -80
Point Programming For Internal or External Power Module (5895XL)

Note: Alarm and trouble signals that have been silenced but the detector remains un-restored will un-silence every 24 hours until it is restored.

8.5.10 Reset alarms

Press RESET and enter your code or rotate the key at the prompt. If an external reset switch has been installed, activating the switch will reset alarms. If you are already using system menus when you press RESET , you will not need to enter your code or rotate the key.
8.5.11 Check Detector Through Point Status
The control panel constantly monitors smoke detectors to ensure that sensitivity levels are in compliance with NFPA 72. If sensitivity for a detector is not in compliance, the panel goes into trouble, generating a CAL TRBLE condition. A detector enters a CAL MAINT state to indicate that it is approaching an out of compliance condition (but is currently still in compliance). When a CAL TRBLE condition occurs, the central station receives a detector trouble report (373 + Zone # for Contact ID format; FT + Zone # in SIA format). To check sensitivity for an individual detector, follow the steps below. Section 8.5.17 provides instructions for printing the status of all detectors in the system. 1. From the Main Menu, press 2. Press

for Point Status.

3. Select the module where the point you want to check is located. 4. Enter the number of the point you want to check and press
5. A screen similar to those shown in Figure 8-4 will display.
Figure 8-4 Checking Detector Sensitivity Compliance
If a printer is attached to the system (via a Module 5824 serial/parallel interface module), you can print detector status (see Section 8.5.17).
8.5.12 View Status of a Point
2. From the list that displays, press ENTER to select the module where this point is located. The screen that displays will show you if the point has a trouble and will provide sensitivity compliance information. (See Section 8.5.11 for complete information about detector sensitivity compliance.)
8.5.13 View Alarms or Troubles
When the system is in alarm or trouble, you can press trouble. See Section 8.5.13 for more information. to view the location of an alarm or
8.5.14 View System Information
Press 8 from the Main Menu to view the panel model and serial number and system version number and date. The information displays for several seconds then returns to the main menu.

Manual release switch trouble (Water Trouble Release Zone) Interlock switch trouble (Water Release Zone) Detector trouble Positive Alarm Sequence acknowledge switch trouble Auxiliary Power Trouble Point Enabled Water flow switch alarm Water flow switch disabled Supervisory/Tamper switch or supervisory duct dectector disabled Water flow switch alarm restore Water flow switch trouble restore Supervisory/Tamper switch or supervisory duct dectector trouble restore Supervisory condition restore Supervisory condition Water flow switch trouble Supervisory/Tamper switch or supervisory duct dectector trouble Trouble Trouble Trouble Trouble Disable Alarm Disable Disable Restore Trouble Trouble
Point Event Point Event Point Event Point Event
pi Exp. ID pi Exp. ID pi Exp. ID pi Exp. ID

SR SS ST ST

Pnt # Pnt # Pnt # Pnt #
Water flow switch re-enabled

Disable

Point Event Point Event Point Event Point Event Point Event Point Event Point Event Point Event Point Event Point Event Point Event Point Event Point Event Point Event Point Event Point Event Point Event Point Event Point Event Point Event Point Event Point Event Point Event
pi Exp. ID pi Exp. ID pi Exp. ID pi Exp. ID pi Exp. ID pi Exp. ID pi Exp. ID pi Exp. ID pi Exp. ID pi Exp. ID pi Exp. ID pi Exp. ID pi Exp. ID pi Exp. ID pi Exp. ID pi Exp. ID pi Exp. ID pi Exp. ID pi Exp. ID pi Exp. ID pi Exp. ID pi Exp. ID pi Exp. ID
SU SU UA UA UA UA UB UH UH UH UH UJ UJ UJ UJ UJ UT UT UT UT UT UU XE
Pnt # Pnt # Pnt # Pnt # Pnt # Pnt # Pnt # Pnt # Pnt # Pnt # Pnt # Pnt # Pnt # Pnt # Pnt # Pnt # Pnt # Pnt # Pnt # Pnt # Pnt # Pnt # Pnt #
Exp. ID Exp. ID Exp. ID Exp. ID Exp. ID Exp. ID Exp. ID Exp. ID Exp. ID Exp. ID Exp. ID Exp. ID Exp. ID Exp. ID Exp. ID Exp. ID Exp. ID Exp. ID Exp. ID Exp. ID Exp. ID Exp. ID Exp. ID
Supervisory/Tamper switch or Disable supervisory duct dectector re-enabled Zone-based AUX1 switch alarm Zone-based AUX2 switch alarm System-based AUX1 switch alarm System-based AUX2 switch alarm Auxiliary switch input disabled Zone-based AUX1 switch alarm restore Zone-based AUX2 switch alarm restore System-based AUX1 switch alarm restore System-based AUX2 switch alarm restore Zone-based AUX1 switch trouble restore Zone-based AUX2 switch trouble restore External Reset/Silence/Fire Drill switch trouble restore System-based AUX1 switch trouble restore System-based AUX2 switch trouble restore Zone-based AUX1 switch trouble Zone-based AUX2 switch trouble External Reset/Silence/Fire Drill switch trouble System-based AUX1 switch trouble System-based AUX2 switch trouble Auxiliary switch input re-enabled An unexpected SLC device has been detected Alarm Alarm Alarm Alarm Disable Restore Restore Restore Restore Trouble Trouble Trouble Trouble Trouble Trouble Trouble Trouble Trouble Trouble Disable Trouble

Testing and Troubleshooting
3) When necessary, activation of Notification Appliances can be prevented by the DISABLE function Testing: 1) Activate a input via an alarm initiating device and check that the correct outputs activate (Notification Appliances sound/flash, relays activate, alarm LED lights). Reset system. Repeat for each alarm initiating device. 2) Momentarily open the following circuits one at a time and check for a trouble signal: Notification Appliance (bell) Circuits. Initiating devices
3) If new batteries were installed, wait 48 hours before completing this step. Remove AC power, activate initiating device and check that: The ALARM indicator lights. All active Notification Appliances sound.
Measure battery voltage while the Notification Appliances are sounding. Replace any battery with terminal voltage less than 85% of rating. Reapply AC power and RESET system.

10.2.2 Event History

The event history can be useful for tracking or recalling a trouble condition.
10.3 Built-in Troubleshooting and Testing Tools
The fire control panel has several built-in testing and troubleshooting tools that can be utilized to save time while testing and troubleshooting points and SLC devices.
10.3.1 SLC Device Locator
SLC device locator can be used to locate a device on a SLC loop. Follow these steps to locate a particular SLC device: 1. Select 2. Select
(Point Functions) from the Main Menu. (SLC Dev Locator).
A message similar to the one shown in Figure 10-1 will display.
Figure 10-1 Shut Down Warning

3. Press the

arrow to toggle NO to YES then press
If NO is chosen you will exit back to the Point Function menu. If Yes is chosen the system will cease normal operation leaving the premise unprotected. 4. Select the SLC loop. 5. Enter the SLC address of the device you wish to locate. The LED on the selected device will start flashing. 6. Press any key to exit SLC device locator function.
Note: Once you exit the system will resume normal operation.

10.3.2 SLC Multi Locator

This feature is the same as SLC Device Locator, except you can locate up to 8 devices on a single search. Follow these instructions to locate multiple SLC devices: 1. Select 2. Select
Figure 10-2 Shut Down Warning
If NO is chosen you will exit back to the Point Function menu. If Yes is chosen the system will cease normal operation leaving the premise unprotected. 4. Select the SLC loop. 5. Enter up to 8 SLC addresses for the devices you wish to locate. The LEDs on the selected devices will start flashing. 6. Press the to exit SLC multi-locator function.

10.3.3 I/O Point Control

This feature allows you to toggle any output on or off and trip any input device. This can be useful to test a points output mapping. Follow these steps to control a I/O point: 1. Select 2. Select