About This Manual

The Model 5207 Fire Control/Communicator Installation Manual (P/N 150865) is intended for those persons involved with the installation and maintenance of the 5207 panel. It is a comprehensive guide, providing detailed instructions, and should be kept for reference. As much as possible, we have tried to organize the manual chronologically by the tasks that need to be performed. This manual is intended to be used with printed circuit board (PCB), Revision M. If you are using a different board, contact Silent Knight Security Systems for the appropriate instructions. IMPORTANT: Previous versions of the 5207 were selectable between 12V and 24V. This release is 24V only. *All information regarding 12V have been removed from this manual. Some versions of the 5207 product documentation were made up of two manuals, one for hardware installation and one for programming. We have combined both manuals into one. With the exception of information about the obsolete 5521 programmer*, this manual contains all information previously contained in the two manuals.
*Contact Silent Knight if you need this information.

KEY LCD DISPLAY MESSAGE

1-1, 2-3, etc.
A clear rectangle represents a key that you press on a touchpad. The font shown to the left represents messages that you see on a liquid crystal display (LCD) or the seven-segment (built-in touchpad) display. This manual is organized into sections. Section numbers are part of the page numbers. For example, 1-1 means Page 1 of Section 1.

Optional Accessories

Table 1-1: Compatible Modules Manufactured by Silent Knight

Model What It Does

4180 Status Display/Relay Module 5210 Zone Expander 5220 Direct Connect Module 5230 Remote Annunciator Quick connect program cable, part number Signal Power Expander
For remote annunciation of alarm and trouble status information for each zone. Adds 8 zones to the 5207 for a total expansion of the system to 16 zones. For direct alarming and trouble transmission from the 5207 to a supervising station. For remote annunciation, operation, and on-site programming. For temporarily connecting the 5230 to the 5207 for programming. Notification circuit power for additional notification appliances. Provides additional 6A of 24 VDC, supervised. For remote programming of the 5207 using a personal computer. Modem for downloading; required if the 5541 software is used. Converts a zone from class B to class A or from class A to class B. One 7181 per zone to be converted.

1. 2. 3. 4. 5. 6.

Requirements for Central Station Fire Alarm Systems
The Ground Fault Detection option must be selected (programming Step 5). The Phone Line #2 Enable option must be selected (programming Step 9). The Phone Line Monitor Enable option must be selected (programming Step 9). Set the Total Attempts option for between 5-10 attempts (programming Step 10). Do not select the Ground Start Option (programming Step 9). Enable the automatic daily test by selecting a phone number for the Report Test to Phone #1-4 option (programming Step 14.4). 7. On class A (style D) zones, the number of waterflow devices is limited to five. 8. Auxiliary relays may not be programmed to activate for Pre-Alarm. See Section 4.13.
Agency Listings and Requirements
Requirements for Auxiliary Protected Fire Alarm Systems for Fire Alarm Service
1. Follow the current load restrictions shown in Section 3.5. 2. The Model 5220 Direct Connect module must be installed (see Section 4.7 for wiring).
Requirements for Remote Station Protected Fire Alarm Systems, for Digital Communication or Polarity Reversal
1. Follow the current load restrictions shown in Section 3.5. 2. Use the 5207s built-in dialer or install the Model 5220 Direct Connect Module (see Section 4.7).
California Fire Marshal (CFM)
The CFM approval number for the 5207 is 7165-0559:111.

Factory Mutual (FM)

The Model 5207 is FM approved under project # OQ1A3.AY when used with the Silent Knight Model 9000 Receiver.
Materials and Equipment Board of Acceptance Division (MEA)
The 5207 is approved under MEA. Approval was previously given from the City of New York Board of Standards and Appeals (BSA), the 5207 is still approved under BSA Calendar Number 703-88-SA.
Section 3 Control Panel Installation
3.1 Electrical Specifications
Table 3-1 Electrical Specifications
Primary AC Total DC Load Accessory Power Smoke Power Battery Charging Voltage Battery Charging Current Class B (style A) Circuit Current Telephone Minimum Input Sensitivity Good Phone Line Voltage Maximum Low Battery Detect Minimum Low AC Detect Maximum Watchdog Response Time Notification Power 120 Vrms at 60 Hz, 2A 5A 18.4 V to 27.6 V max., 1A 18.4 V to 27.6 V max., 1A 27.3 2.62 A max. 60 mA max. 45 dB 3V 20.4 sec. 1A max. per output (4A total)
Environmental Specifications
It is important to protect the 5207 control panel from water. To prevent water damage, the following conditions should be AVOIDED when mounting the units: Do not mount directly on exterior walls, especially masonry walls (condensation). Do not mount directly on exterior walls below grade (condensation). Protect from plumbing leaks. Protect from splash caused by sprinkler system inspection ports.
Do not mount in areas with humidity-generating equipment (such as dryers, production machinery). When selecting a location to mount the 5207 control panel, the unit should be mounted where it will NOT be exposed to temperatures outside the range of 0 C-49 (32 C F-120 or F) humidity outside the range of 10%-85% at 30 (86 noncondensing. C F) See also the mounting recommendations in 3.7 for additional environmental specifications.

Figure 3-4 Battery Calculation Example
5. Refer to to verify the battery size you need to provide at least the total standby current you have calculated. If the installation must meet requirements for NFPA 72 (Auxiliary Protected Fire Alarm Systems for Fire Alarm Service or Remote Station Protected Fire Alarm Systems, Digital Communication or Polarity Reversal), the total standby current cannot exceed the amount shown in the last column of the following table:
Table 3-4 Maximum Battery Standby Load Rechargeable Battery Size 17 AH 34 AH (if wired in parallel) (Largest size battery that can be used.) Max. Load for 24 hrs. Standby, 5 mins. Alarm 435 mA 873 mA *Max. Load for 60 hrs. Standby, 5 mins. Alarm 175 mA 350 mA
* Required for NFPA 72 Auxiliary Protected Fire Alarm Systems for Fire Service (City Box) and Remote Station Protected Fire Alarm Systems (Polarity Reversal).
6. Ensure that the total current of all items attached to the 5207, including the 5207 itself, does not exceed 5 A when the panel is in alarm (see Section 3.1).

Power Supply Wiring

The Model 5198 power supply delivers 24 VDC at 5A for loop power, smoke detector power, notification device power, and accessory power. The Model 6914 is a 12-Volt, 17-AH battery. Figure 3-5 shows the power supply wiring.
Figure 3-5 Power Supply Wiring
Warning To reduce the risk of electrical shock, make sure that all power has been turned off or disconnected before attempting to connect the Model 5198 power supply. Do NOT apply power to this panel until all accessories are properly connected.
Note: All conduit and wiring connected to the 5207 must meet the applicable National Electric Code, NFPA Standards, state, and local building code requirements. In all cases, the authority having jurisdiction takes precedence.
Connecting the 5198 to AC Power
The Model 5198 is mounted behind the power shield. Connect the black wire from the 120 VAC 60 Hz source to terminal 1 on the 5198. Connect the white (neutral) wire from the 120 VAC 60 Hz AC source to terminal 3 on the 5198. Connect the ground wire from the 120 VAC 60 Hz source to terminal 2 on the 5198.
Connecting the 5198 to Batteries
The tables in Section 4 will help you determine correct battery size. Caution
Apply AC power before connecting the batteries to the power supply to prevent arcing on battery terminals.
When using two batteries, it is recommended that they be of the same ampere hour (AH) rating. The Model 5198 provides two sets of battery leads to connect two 12 VDC batteries in series. 1. Connect the first red battery lead to the positive side of battery #1. 2. Connect the first black battery lead to the negative side of battery #1. 3. Connect the second red battery lead to the positive side of battery #2. 4. Connect the second black battery lead to the negative side of battery #2. Note: The total current draw on loop power, accessory power, and notification device outputs must not exceed 6A.

Note: The 3158 Keltron Module must be mounted within 3 feet of the control panel and all wiring must be run in conduit. The Keltron Module shall be enclosed in the TBX1 enclosure.
1. Wire the 3158 to the 5207 as shown in the figure below. 2. Program Relay 3 to activate for all trouble conditions and no silence. Relay 2 should be programmed to activate for Alarms. 3. Program notification circuit 3 and 4 to be non-supervised and non-silencing. 4. Program Bell 3 as Special. The chart below shows which selections to make in step programming.
Step Option Select De-select

5 23.3 23.4 23.5 23.6

Misc Opts Special Fire Alarm Trouble No Silence
Bell 3 and Bell 4 Bell 3 Relay 2 and Bell 4 Relay 3 Relay 3, Bell 3 and Bell 4 Bell 3
Note: DO NOT select pulsing bells.
Figure 4-9 Wiring the Keltron 3158 to the 5207

150865 4-9

Model 5230 Remote Annunciator
The 5230 performs all system operation. It also provides trouble and alarm information and can be used for programming.

Setting ID Codes

Before permanently installing the Model 5230 Remote Annunciator, you must first set its identification codes. Each annunciator to be supervised must be given its own identification codes. The ID numbers must start at 1 and progress sequentially to 7 (7 annunciators max.). Upon initial power up, the address of each annunciator is displayed. (Annunciators with address 0 will not be supervised.) On the back of each annunciator is a small 4-position dip switch used to set the ID code. Use the chart below to determine the dip switch positions for each possible ID code.
Table 1-1: Model 5230 Dip Switch Settings
ID Number 0* 7 *Not supervised Switches 1 Up Down Up Down Up Down Up Down Up = On 2 Up Up Down Down Up Up Down Down Down = Off 3 Up Up Up Up Down Down Down Down 4 Up Up Up Up Up Up Up Up
5230 Permanent Connection
Wire permanent 5230s as shown in Figure 4-10. When the annunciator powers up, it will display its ID code and current status of the panel. A temporary 5230 can be connected for programming and troubleshooting. See Section 4.9.4 for temporary annunciator connection.
Figure 4-10 Model 5230 Connection
Mounting the 5230 Remote Annunciator
For UL installations, the 5230 Remote Annunciators must be mounted on a dual gang electrical box and all wiring runs must be made using 18-gauge wire or larger. To mount the annunciator: 1. Remove the rear mounting plate by inserting a #4 flat blade screwdriver into the slots on the bottom edge of the annunciator. Gently turn the screwdriver until the mounting plate pulls away from the frame. 2. Secure it to the wall using #6 or #8 screws. The mounting plate should be oriented so that the word TOP is toward the top of the plate and facing you. A square hole is provided in the mounting plate to run the wiring to the annunciator. 3. When all of the wires have been connected to the annunciator, set the top of the annunciator over the tabs on the top of the mounting plate. Make sure the wires do not get pinched between the frame and the mounting plate. Press each corner of the bottom side onto the annunciator mounting plate until you hear it click. You may have to gently squeeze the annunciator (top to bottom) to align it while snapping the bottom edge into place.

Temporary Annunciator Connection
If you are using an annunciator for programming or troubleshooting only, you can use cable P/N 130294 (ordered separately) to temporarily attach the 5230 at connector P3. Figure 4-11 shows the connections. A temporary annunciator must have an ID number (1 or higher) but does not need to be enabled through programming.
Figure 4-11 Temporary Annunciator Connection
Model 5395 Signal Power Expander
The Model 5395 is a notification and auxiliary power expander that provides up to 6.0 amps of regulated, 24-volt power for powering notification appliances and auxiliary devices. Figure 4-12 shows you how to connect the Model 5395 to the Model 5207 panel. See the 5395 installation manual (P/N 150933) for complete information.
Figure 4-Connection to 5207
Model 7181 Zone Converter
The Model 7181 Zone Converter lets you interchange zone types on the 5207. Figure 4-13 and Figure 4-14 show how to make conversions. Refer to the Model 7181 Installation Manual (P/N 150632) for complete information.
Figure 4-13 Connecting Class A (Style D) Sensor to Class B (Style A) Panel
Figure 4-14 Connecting Class B (Style A) Sensor to Class A (Style D) Panel
Supervised Notification Appliance Outputs
Note: To reduce the possibility of false alarms and transient damage, DO NOT bundle telephone wires together with notification circuit wires.
The 5207 provides four supervised notification circuit outputs to annunciate alarm conditions. For proper operation, you must use polarized sounding devices with a 4.7k ohm end-of-line resistor on each loop. Figure 4-15 shows how to connect the notification circuits to the 5207.
Figure 4-15 Supervised Notification Appliance Wiring
See Appendix A for a list the UL sounding appliances that can be used with the 5207. Contact Silent Knight if you have any questions about compatible notification circuits.

Auxiliary Relays

The 5207 provides four programmable auxiliary relay outputs. Relays can be programmed to activate for the following conditions, either for all zones or by individual zone: pre-alarm (entry delay) (not acceptable for NFPA 72 Central Station), fire alarm, auxiliary alarm, alarm by zone, and system or loop troubles (loss of AC, low battery, failed to communicate, phone line troubles, and notification circuit troubles). Refer to the 5207 programming manual for more information. Figure 4-16 shows the relay contact connections using a doorstrike application as an example.

CLEAR CLEAR

Display alarm memory
Displays current alarm memory. (It is recommended that you clear alarm memory after displaying it.) Displays trouble conditions. If silencing audible signals, you may need to enter a code.
Display troubles Silence troubles or alarms

SILENCE

+ code + code

7 ENTER 7

Operation

Table 5-Operation

To 5230 Annunciator Set date

8 ENTER

+ code 0 or 1

See explanation below.

The SET MODE LED will turn on and the built-in touchpad display will flash "-8" indicating that you are in SET DATE mode. Enter six digits for the date. For example, to set the date for 08/15/97, enter the following digits: Once you press the last digit of the date, the SET TIME LED will turn off and the date will be changed. To exit Set Date mode, press Set time

9 CLEAR ENTER CLEAR 9 7

9 ENTER
The SET MODE LED will turn on and the built-in touchpad display will flash "9" indicating that you are in Set Time mode. Enter six digits for the time. The first digit indicates day of the week ( 0 = Sunday, indicates time of day (
= Monday, etc.). The second digit
= PM). The last four digits are the actual time. For example, to set the time for Wednesday,
. 4:30 p.m., you would enter: Once you press the last digit of the time, the SET TIME LED will turn off and the time will be changed.
To exit Set Time mode in the middle of the sequence, press
Note: If you are powering up the 5207, you will be in Set Time mode with "-9" showing on the display. In thise case, you dont need to press
. Just enter the six digits for the time. Zone # +

DISABLE

Disable/Enable zones

Zone # +

Disables or enables a zone. When a zone is disabled, there will be an alert tone that cannot be silenced until the zone is enabled. Complete instructions appear in Section 5.2.1.

Fire drill

Begin:

End: Walk test

Enter:
Complete instructions appear in Section 5.2.2.

Section 6 Programming: Quick Reference
This section of the manual briefly describes all available programming options and lists the factory programmed default values. Section 7 of this manual is a complete, step-by-step guide that provides details, including LCD diagrams, of each programming step. Please read Section 7 thoroughly, especially if you have never programmed the 5207 before. The quick reference chart can be used for keeping track of how options have been programmed for an installation. The drawing below explains how to use the quick reference chart.
Figure 6-1 How to Use the Programming Quick Reference Chart
Step # 1 Pg. 7-Pg. 7-4 1st digit: Bell Test at Restore: 0 = No test 8 = Test Enable Devices: 0 = Dialer 1 = Printer
Option 2nd digit: Power up Mode Report: 0 = No report 1 = Report sent

Default 00

Your Selection
0------7 2-6 Unused 7 = 24V system (Do not change factory programming.) ------64 = Sound smoke delay 5 = Report fast restores 6 = Do not de-select. 7 = Time displays in military format

3 Pg. 7-5

Options: 0 = Cadenced pulsing of bells 1 = Code required at panel 2 = Trouble alert tone for pre-alarm sound 3 = Pulsing fire bells
Step # 4 Pg. 7-5 1st digit: (Display Rate) 0 =.5 sec 1 = 1 sec. 2 = 1.5 sec. 3 = 3 sec. Misc. Options: 0 = Report walk tests 1 = Do NOT de-select 2 = Detect ground fault
Option 2nd digit: 0-7 = Max. number of supervised touchpads (0 means none.)

Default 20

5 Pg. 7-6
-= Sequential bell test 4 - 7 = Supervise bells 1-4
6 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 6.10 Begins on Pg. 7-7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 7.9 7.10 Begins on Pg. 7-Pg. 7-Pg. 7-10
Internal Zone Options (zones 1-8) 24-hour alarm (do not change default) Select zones to be supervised for trouble Unused (do not change default) Zones will be Normally Open (do not change default) Zone response speed 2 or 4 Zone response speed 3 or 4 Unused Pre-alarm delay Smoke verification delay Number of zones that can be disabled -----------------------------------12345678
__________________________
__________________________ __________________________ __________________________ __________________________ __________________________
External Zone Options (zones 9-16) 24-hour alarm (do not change default) Select zones to be supervised for trouble Unused (do not change default) Zones will be Normally Open (do not change default) Zone response speed 2 or 4 Zone response speed 3 or 4 Unused Pre-alarm delay Smoke verification delay Number of zones that can be disabled -----------------------------------90123456
Total number of zones in system
Dialer Options: 0 = Retry if fail 1 = Enable phone line = Unused (do not select) 3 = Ground start (do not use in UL installations) 4 = Enable phone line monitor 5 = Answer ring detect 6 = Unused (do not select) 7 = Up/downloading

The Model 5230 Remote Annunciator is for programming the 5207 panel. You must be in Step Programming Mode (also known as mode 27) to program the panel. See the following sections for details.

Using Step Programming

Press ENTER , followed by the code that has been programmed as code 0 (the factory programmed value for code 0 is 123456). If you have entered mode 27 correctly, the display will show 1 PWR UP CLR (Step 1, Power-up Clear). Press ENTER to make selections for this step. Press ENTER again to move to the next step.
Note: If you receive a trouble beep and the message TRY AGAIN appears, either you are not using the correct code 0, or the EEPROM could be malfunctioning. If the problem is the EEPROM, you must obtain a new default EEPROM from Silent Knight.
Enter Step Programming mode
Exit Step Programming Moving through the Steps and Sub-Steps

STEP STEP CLEAR CLEAR

. You will return to normal operation.
To move sequentially through the options: Press ENTER until you reach the step (option) you want to program. To go directly to step: If you know the step you want to go to, you can save time by moving directly to the step. Press STEP STEP. Enter the desired step number, then press ENTER. The new step will be displayed. To go to directly a sub-step: Some steps contain sub-steps (see the diagram on the next page for an example). To go to a particular sub-step, first go to the step. Then, press STEP followed by the substep number and press ENTER. For example, to go to step 14.2, you would press the following sequence of keys: STEP STEP ENTER STEP 2 chart continued on next page

Selecting Options

Scrolling For most options, you enter numbers in the same way as if you were using a calculator. The digits appear on the right side of the display and scroll to the left as you continue to enter data.
Toggling In some steps, pressing a key will cause the corresponding digit to appear and disappear on the display. When a digit appears, it indicates that the option is selected. A dash indicates that the option is not selected. In the following example, options 1, 5, and 7 are selected:
Entering numbers greater than 9 Use the SHIFT key as shown below to enter numbers 10-15. Hexadecimal digits (in parentheses) appear on the screen to represent these numbers.

ENTER.

From the 1 PWR UP CLR display, press Press
Press the number of the code you want to add or change. Press
Enter the new access code number. Press

Step Programming Options

This section is organized in step order and provides complete instructions for each step.

Step 1. Power Up Clear

Display Description
The two digits of this step are used to program two options, BELL TEST AT RESTORE (digit 1) and DEFAULT MODE (power up) REPORTING (digit 2). Digit 1: 0 = No bell test at restore. 8 = Bell test will occur at restore. Digit 2: 0 = A report will not be sent if the system enters power up mode. 1 = An "open" report will be sent if the system enters power up mode. Example 1: If you select "80" for this step, a bell test will occur at restore (digit 1) and no report will occur if the system enters power up mode (digit 2). Example 2: If you select "01" for this step, a bell test will not occur at restore (digit 1) and the system will report "Open" if it enters power up mode (digit 2).

Step 2. Device Enables

Step 2 allows you to enable the dialer, printer, and 24-volt smoke power. 0 = Dialer. The dialer must be enabled. Do not change the factory programming. 1 = Printer. Enable the printer if your installation includes a 5260 printer interface. (The 5260 is not UL listed for use with the 5207.) 7 = 24-V System. Enables 24V power. Do NOT disable. 2 - 6 = Unused. These digits are reserved by the manufacturer for future use. Leave these blank at all times.
Step 3. More System Options
Step 3 allows you to select seven system options shown below. To select an option, press its number. 0 = Cadenced pulsing of bells. If you select this option, bells will pulse in the pattern shown below (for customizing patterns, refer to Steps 27 and 28): 3.5 seconds on,.5 seconds off 3.5 seconds on,.5 seconds off 3.5 seconds on, 4.5 seconds off 1 = Code required at the panel. If you select this option, users will have to enter a code to perform tasks on the built-in touchpad. 2 = Trouble alert tone used for pre-alarm sound. If you choose this option the built-in trouble alert will sound when a trouble condition occurs. 3 = Pulsing fire bells. Select this option if you want fire alarm bells to pulse one second on, one second off. (If you want fire bells to have cadenced pulsing instead of one second on, one second off pulsing, choose both this option AND cadenced pulsing.) 4 = Trouble alert tone will sound during smoke delays. If you choose this option, the built-in trouble alert sounder will sound when a trouble condition occurs. 5 = Report fast restores. This option causes restores that occur as soon as the alarm situation is corrected instead of waiting for the shutdown time. 6 = Must be enabled. Do NOT de-select. 7 = Time displays in military format. If you select this option, the system time will display in the 24-hour military format instead of the 12-hour with AM/PM format.

Not used. Do not select any zones for this option.
Pre-alarm delay. Use this step to select a pre-alarm delay for zones 1 to 8. When this delay is selected for a zone, it means that the panel will not immediately go into alarm. Alarm responses and reporting will be delayed for the programmed duration (duration programmed in Step 20.3). Any outputs programmed for pre-alarm (in Step 23.1) will activate. At the end of the prealarm time, if the alarm has not been reset, the panel will go into alarm. Smoke verification delay. For use with smoke detectors only (not for manual pull stations). Use this step to select any zones that will be controlled by a smoke detector delay. This means that the smoke detector will delay for a specified amount of time before responding to an alarm condition. (The duration of the delay is programmed in Step 20.4.) Can be disabled. For zones 1-8, enter the number of zones that can be disabled.
Step 7. External Zone Options
24 Hour alarmZones will be active 24 hours. Must be selected for all zones. Do NOT change the factory programming for this step.
Trouble supervisedFor zones 9 to 16, enter the number of zones that will be trouble supervised.
Not used. Do NOT select any zones for this option.
This step sets all expansion zones as Normally Open. Do not change the factory programming for this step.
Use this step to select the 3-to-4 second or 30-to-40 second loop response time for zones 9 to 16. If you need more information about how to program loop response time, see the explanation at Steps 6.5 and 6.6.
Use this step to select the 15-to-20 second or 30-to-40 second loop response time for zones 9 to 16. If you need more information about how to program loop response time, see the explanation at Steps 6.5 and 6.6.
Pre-alarm delay. Use this step to select a pre-alarm delay for zones 1 to 8. When this delay is selected for a zone, it means that the panel will not immediately go into alarm. Alarm responses and reporting will be delayed for the programmed duration (duration programmed in Step 20.3). Any outputs programmed for pre-alarm (in Step 23.1) will activate. At the end of the prealarm time, if the alarm has not been reset, the panel will go into alarm.

Table 8-3: 16-Zone 4+2 Format

Zone Code Description

Alarm Zone 1. Alarm Zone 8 Alarm Zone 9 Alarm Zone 10 Alarm Zone 11. Alarm Zone 16 Trouble Zone 1. Trouble Zone 8 Trouble Zone 9 Trouble Zone 10 Trouble Zone 11. Trouble Zone 16 Restore Zone 1. Restore Zone 8 Restore Zone 9 Restore Zone 10 Restore Zone 11. Restore Zone 16
ALARM 1. ALARM 8 ALARM 9 ALARM 10 ALARM 11 ALARM 16 TROUBLE 1. TROUBLE 8 TROUBLE 9 TROUBLE 10 TROUBLE 11 TROUBLE 16 RESTORE 1. RESTORE 8 RESTORE 9 RESTORE 10 RESTORE 11 RESTORE 16

Radionics BFSK Format

Model 5207 can transmit using the Radionics BFSK format with 1400 Hz or 2300 Hz acknowledge. The messages that will be printed are listed with the codes for FSK1 and SK 4+2. Radionics BFSK format can only report eight zone codes. Zones 9 through 16 report as zones 1 through 8; zones 17 through 24 report as zones 1 through 8, and so on. Because of this limitation, programming the 5207 to report in both the Radionics BFSK and either the FSK or SK 4+2 formats is NOT advised. Use only if required by the receiver. The Radionics BFSK format repeats after 8. It is recommended that you use no more than 8 zones if your system is programmed to report in Radionics BFSK format. However, if you choose to use more than 8 zones with the Radionics BFSK format, it is a good idea to make every 8th zone (such as Fire, Tamper Sprinkler, etc.) the same zone type (such as Fire). If you assign the zones in this manner, the letter X in will be a digit that represents every 8th zone number, as shown below:
Digit Reported (X) Zone Numbers 5 13. 16
Table 8-4: Radionics BFSK
BFSK Radionics BFSK Description

Fire Codes X E0 F0 FX EX

Alarm Zone X Restore Zone 0 Trouble Zone 0 was Forced Armed Trouble Zone X Restore Zone X
Alarm on zone X (see chart above for actual number). Disable restore zone 0. Trouble zone 0 (zone disabled). Trouble zone X (see chart above page for actual number). Alarm or trouble restore zone X (see chart above for actual number).
Other Zones E9 Restore Zone 9 Test/restore zone 9. FB Trouble Zone B Phone line fault *FC Trouble Zone C Expansion trouble (see Note below) EB Restore Zone B Phone line trouble restore. *EC Restore Zone C Expansion restore (see Note below) E9 Test/restore Zone 9 Data lost. F0 Trouble Zone 0. AC lost. F9 Trouble Zone 9. Low battery. E0 Restore Zone 0. AC restore. E9 Restore zone 9 Battery restore. BY Open zone (Code #) Reset alarm by user code #. Note: "Expansion" refers to all expansion trouble/restores listed in SIA format, Table 8-1.

Model Name or Number (Base model name or number in parentheses.) 429CST (S11A) 429CT (S10A) 609U01-11 609U02-11 611U (601U or 602U) 611UD (601U or 602U) 611UT (601U or 602U) 612U (601U or 602U) 612UD (601U or 602U) 711U (701E or 701U) 712U (701E or 701U) 713-5U (702E or 701U) 713-6U (702E or 701U) 721-U (S10A) 721-UT (S10A) 525 525T 9376 SIH-24F (HS-224D or HSB-224) SLK-12 SLK-24F (HS-224D) SLK-24FH (HS-224D) (HS224L) Heat Detector base 1100 1100T 1100TB 1151 (110LP) (B401B) 1800 1851B (B101B) 1851DH (DH1851DC) 2100 2100T 2100TB 2151 (B110LP or B110LRP) 2300T (DH400) 2400AIT 2400AT 2400TH
/ loop 30 / loop 40 / loop 40 / loop 40 / loop 40 / loop 40 / loop 40 / loop 40 / loop 25 / loop 25 / loop 25 / loop 25 / loop 30 / loop 30 / loop 17 / loop 17 / loop 20 / loop 20 / loop 20 / loop 25 / loop 25 / loop 25 / loop 25 / loop 30 / loop 20 / loop 20 / loop 20 / loop 20 / loop 20 / loop 20 / loop 20 / loop 20 / loop 20 / loop 20 / loop 20 / loop 20 / loop 20 / loop 20 / loop 20 / loop 20 / loop 20 / loop 20 / loop 20 / loop
/ loop 14 / loop 24 / loop 24 / loop 24 / loop 24 / loop 24 / loop 24 / loop 24 / loop 15 / loop 15 / loop 15 / loop 15 / loop 15 / loop 15 / loop 8 / loop 8 / loop 10 / loop 10 / loop 10 / loop 10 / loop 10 / loop 10 / loop 10 / loop 30 / loop 8 / loop 8 / loop 8 / loop 8 / loop 8 / loop 8 / loop 8 / loop 8 / loop 8 / loop 8 / loop 8 / loop 8 / loop 8 / loop 8 / loop 8 / loop 8 / loop 8 / loop 8 / loop 8 / loop
System Sensor System Sensor System Sensor System Sensor System Sensor System Sensor System Sensor System Sensor System Sensor
Model Name or Number (Base model name or number in parentheses.) 2451 (B401B) 2451DH (DH 400) 2451TH (B401B) 2800 2800TH 2851B (B101B) 2851BTH (B101B) 2851DH 2851TH (B101B)
/ loop 20 / loop 20 / loop 20 / loop 20 / loop 20 / loop 20 / loop 20 / loop 20 / loop
/ loop 8 / loop 8 / loop 8 / loop 8 / loop 8 / loop 8 / loop 8 / loop 8 / loop
Four Wire Smoke Detectors
Manufacturer Silent Knight Detection Systems ESL System Sensor Model SD-P24F with SD-B4@ base DS200/DS200HD MBSeries 449 Series 1851B 2851/2851BTH DH200ADCD

Model 5207 Fire Alarm Built-in Touchpad Operating Instructions
These instructions must be framed and displayed next to the Model 5207 panel in accordance with NFPA 72 fire code for Local Protected Fire Alarm Systems. Basic Operation of Built-in Touchpad Function System test* Reset alarms (or smoke detectors)* Clear alarm memory* Reset dialer Start download Alarm memory display Display troubles Silence troubles or alarms* Disable/Enable zones Begin fire drill
0 ENTER 1 ENTER 2 ENTER 3 ENTER + code 0 or ENTER + code 0 or ENTER 6 ENTER 7 ENTER + code, or SILENCE + code

Keystrokes

Function Set date* For example, to set the date of Jan. 13, 1995, enter: Set time* For example, to set the time of Wed., 4:30 p.m., enter: 3 0
Keystrokes 8 ENTER + 6-digit date Use mmddyy format for date, where: mm = Month (enter leading 0 for 1-digit months) dd = Day (enter leading 0 for 1-digit days) yy = Year 9 ENTER + 6-digit date Use wdhhmm format for time, where: w = Day of week (0=Sun., 1=Mon., 2=Tue., 3=Wed., 4=Thu., 5=Fri., 6=Sat.) d = Time of day (0=AM, 1=PM) hh = Hour (enter leading 0 for 1-digit hrs.) mm = Minutes (enter leading 0 for 1-digit min.)

Zone # + DISABLE

ENTER + code 0 or 1
To exit download, set date, and set time modes, press CLEAR CLEAR. * These functions do not require you to enter a valid operating code unless the NEED CODE AT PANEL option is selected during programming. For service call:
The system sounds an alarm and reports a fire test when you exit fire drill mode. End fire drill Walk test Zone Troubleshooting mode Step Programming mode
SILENCE + code 0 or 2 ENTER + code ENTER + code ENTER + code 0

Form # 150486