Simrad AP11

Autopilot

A L W A Y S

F O R E F R O N T

T E C H N O L O G Y

This page is intentionally left blank

Instruction manual

Instruction Manual
This manual is intended as a reference guide for operating and correctly installing the AP11 autopilot. Great care has been paid to simplify operation and set-up of the Robertson AP11, however, an autopilot is a complex electronic system. It is affected by sea conditions, speed of the vessel, hull shape and size. Please take time to read this manual to get a thorough understanding of the operation and system components and their relationship to a complete AP11 autopilot system. Other documentation materials that is provided with your system include a warranty card. This must be filled out by the authorized dealer that performed the installation and mailed in to activate the warranty.

20220513E

Robertson AP11 Autopilot

Document revisions

Documentation department Rev A B C D E Date 07.03.97 10.07.97 16.02.98 28.09.98 26.01.00 02.01.02 Sign

N.G. N.G. N.G. N.G. N.G.

Hardware/Software design Date 07.03.97 Sign
Project/Product Management Date 07.03.97 10.07.97 16.02.98 28.09.98 26.01.00 02.01.02 Sign
Th.H. Th.H. Th.H. Th.H. Th.H.

Document history

Rev. Rev. A First edition Diagrams for J300X and J3000X Terminal Boards included, page 48. Missing text on illustration page 37 added. Misprint page 47 corrected. Distributor list updated. Minor corrections in text on pages 2, 10, 12, 21, 27, 28, 50, 55, 56, 57, 59, 62 and 64. Correction of display picture for small course changes, page 23, correction in text under Display backlighting page 36 and new part no. for Seal plug, page 100. LFI3000 substituted by LFI3000 Mk2. Distributor list updated. Added note page 53. Added text on page 54 (par. 8). Distributor list updated.

Rev. B Rev. C

Rev. D Rev. E

Contents

1 INTRODUCTION....7 1.1 1.2 1.3 1.4 1.5 1.6 1.7 General....7 System Components...8 AP11 Control Unit...9 J3000X and J300X Junction Unit...10 RF300 Rudder Feedback Unit..11 RFC35 Fluxgate compass...11 Optional components...12 CDI35 Course Detector Interface...12 RFC35R Rate compass...12 LF3000 Linear Feedback...13 LFI3000 Mk2 Linear Feedback Interface..13 "Rudder" Indicator...14 "Compass" Indicator....14 R3000X Remote Control...15 S100 NFU steering lever...15 Overview....16 On/Off....18 Standby....18 Standby- Compass mode...19 AP11 with MSD50 Stern Drive unit..19 Zero point setting....19 Operation....20 Non-Follow-Up electrical steering...20 NFU Steering Lever...21 Hand held remote...21 Standby-Nav mode...21 Standby - Wind mode...22 Automatic Steering...22 Auto Compass mode...23 Nav. displays in Auto Compass mode..24 Dodging...25 U-Turn....26
AP11 AUTOPILOT OPERATION...16 2.1 2.2 2.3 2.4 2.5
2.6 2.7 2.8 2.9 2.10 2.11 2.12 2.13 2.14
2.15 2.16 2.17 2.18 2.19 2.20 2.21 2.22 2.23 2.24
Tacking in Auto Compass mode..27 Clutch/bypass switch...27 Navigating with the AP11...28 Auto Navigation Mode...29 Nav. displays in Auto Navigation mode..30 Wind vane steering...31 Auto W/A mode...31 Tacking in AUTO W/A mode..33 Nav. displays in Auto W/A mode..34 Multistation operation...34 Remote Control...35 User settings...36 Display backlighting....36 Manual speed selection....36 Manual selection of Sea State Filter..37 Alarms....38 Demo mode...38 INSTALLATION....40 General....40 Installation checklist....40 Unpacking and handling...41 Determine system configuration...42 AP11 Basic system...42 AP11 connected to a IS11 instrument system..43 AP11 system with options...43 AP11 system with special J300X options..44 RF300 Rudder feedback installation...44 Junction unit installation...46 Cable connections...46 Grounding and RFI...47 Drive unit installation...49 Connecting a reversible pump...51 Connecting a hydraulic linear drive...51 Separate clutch/bypass switch...51 Connecting a solenoid valve...52 Control Unit Installation...53

2.25 2.3.1 3.2 3.3 3.4

3.5 3.6

3.9 3.10 3.11 3.12 3.13

RFC35 Fluxgate Compass installation...55 RFC35R Rate Compass...56 R3000X Remote Control installation...57 S100 NFU Lever installation...58 Interfacing....59 J3000X NMEA input/output...59 Databox connection...60 IS11 instrument installation...61 J300X/J300X-40 NMEA input/output..61 J300X Radar Clock/Data...62 J300X External Alarm...62 LF3000 Linear Feedback...63 CD100 Course Detector....65 CDI35 Interface...66 Software Setup Procedure..67 Description of Installation Settings...67 AP11 Installation menus...68 Dock-side settings...70 Display illumination colour...71 Boat type....71 Drive unit voltage...71 Rudder feedback calibration...72 Rudder Test....72 Compass setup...74 Radar...74 Transition speed....74 Master Reset...75 Sea Trial...76 Rudder zero adjust...76 Compass calibration...78 Compass Offset...78 Automatic tuning....79 View parameters...80 Final sea trial....83 Providing user training....84 Control unit....85 Removal of the Control Unit...85 5

The AP11 autopilot system includes NMEA0183 input and output ports. The NMEA input allows a single navigation receiver and speed and wind sensors to provide input to the system. The NMEA output provides heading and rudder angle to separate IS11 instruments or to the IS11 Databox. Depending on the autopilot configuration and the equipment that may be connected to the NMEA input, other NMEA data may also be available at the NMEA output. The time proven experience of the Robertson engineers and the computer power in the AP11 system has made it possible to automate and simplify the setup and installation procedures. One important feature is the capability to set up automatically the steering parameters and select the scaling factor for speed and hull type; power (planing or displacement) or sail. Proportional rate output commands and an adaptive sea state filter contribute to enhanced steering performance in any sea condition.

System Components

A basic AP11 autopilot system consists of: AP11 Control Unit, J3000X or J300X Junction Unit, RF300 Rudder Feedback Unit, RFC35 Fluxgate Compass and Drive unit.

RFC35 FLUXGATE COMPASS

AP11 CONTROL UNIT
RPU80/RPU160 REVERSIBLE PUMPS J3000X/J300X JUNCTION UNIT
MAINS POWER SUPPLY 12/24 VDC

RF300 RUDDER FEEDBACK

Figure 1 AP11 Basic system

AP11 Control Unit

110 mm [4,33"]

ROBERTSON AP11

50 mm Dia. [1,97"]

STBY-AUTO PWR

RESPONSE

AUTOPILOT

17 mm 18 mm [0,67"] [0,71"]
Figure 2 Control Unit Dimensions A compact autopilot control for panel or bulkhead mounting. Large LCD display for readout of autopilot data.
J3000X and J300X Junction Unit
Figure 3 J3000X and J300X dimensions The junction unit is the heart in the AP11 autopilot system. It contains the steering computer, interface circuits to all system components and drive circuits for the drive unit motor and clutch. Two models, J300X and J3000X are available. J3000X Supply voltage Motor current (continuous/peak) Number of control units NMEA ports Input for NFU control External alarm Radar clock/data interface (Anritsu and Furuno radars) Table 1 Junction unit comparison chart 10-28 V 6/10 A x J300X 10-28 V 10/20A x x x

RF300 Rudder Feedback Unit
Figure 4 RF300 Dimensions Rudder feedback unit with transmission link and 10 m (30 feet) of cable. Transforms the angular travel of the rudder to a digital signal read by the autopilot steering computer. (See also optional linear feedback on page 13).

RFC35 Fluxgate compass

Figure 5 RFC35 Dimensions A compact heading sensor from Robertson with 15 m (45 feet) of cable. The direction of the earth's magnetic field is sensed by a coil with a floating ring core and transformed to a digital signal read by the autopilot steering computer.

Optional components

CDI35 Course Detector Interface
Figure 6 CDI35 dimensions Interface unit to connect autopilot to magnetic compass with CD100 Course Detector. Provides excitation current for CD100 and converts the analogue sin/cos signal to digital format for the autopilot steering computer.

RFC35R Rate compass

Fluxgate compass with integrated rate sensor. Provides a dramatic improvement to the dynamic performance of both the autopilot and a stabilized radar display. Same dimensions as RFC35.

LF3000 Linear Feedback

Figure 7 LF3000 dimensions Linear feedback unit for boats with outboard engine. Transforms the linear movement to an analogue signal. Supplied with 8,5 m cable and mounting clamps.
LFI3000 Mk2 Linear Feedback Interface
Figure 8 LFI3000 Mk2 dimensions Interface unit for LF3000 Linear Feedback. Converts the analogue LF3000 signal to the standard digital feedback signal for the autopilot steering computer.
"Rudder" Indicator

50mm Dia.

17mm 18mm
Figure 9 Robertson IS11 analogue display dimensions A 12 V Dataline instrument that can be connected directly to the NMEA output on the junction unit. Analogue display of boats' rudder angle.
"Compass" Indicator
A 12 V Dataline instrument that displays the boats heading on both digital and analogue format. Can be connected directly to NMEA output on the junction unit. Dimensions as for "Rudder" Indicator.

REMOTE REMOTE REMOTE

STBY-AUTO STBY-AUTO STBY-AUTO
Remote mode switching (from STBY)

INITIAL MODE

ENDING MODE AUTO COM

Light ON

STBY COM

Light OFF

STBY NAV

AUTO COM

Note: not AUTO NAV

STBY W/A

AUTO W/A
Remote mode switching (from AUTO)

REMOTE REMOTE

ENDING MODE STBY COM

AUTO NAV

STBY-AUTO STBY-AUTO
Light OFF Note: not STBY NAV

User settings

A group of user adjustable settings are provided in the AP11 autopilot. The settings are described below.

Display backlighting

Press and hold MODE button

(From any mode)

Lighting can be set to eight different levels: 0 (Off) - 7 (brightest). The display returns to the previous one when the Mode button is released.

Manual speed selection

Note ! Prior to making a manual speed selection it is recommended that you study the "Transition Speed" paragraph on page 74 to get a clear understanding of the automatic speed selection feature. The AP11 automatically selects the HI speed parameters at turn on. If you change boat speed it is recommended that you select HI or LO parameters correspondingly.
HI speed response level selected
LO speed response level selected
Short press on both and Mode buttons
You can manually toggle between the two levels as shown. The manually selected steering parameter set (HI or LO) will remain in effect until AUTO mode is re-entered.
Manual selection of Sea State Filter
Press and hold both the and the Mode button
Select filter setting using < (decreasing) or > (increasing). Filter setting OFF AUTO Description Tightest steering. Most active rudder. Automatically sets autopilot sensitivity according to sea state (adaptive). Lowest yaw band value that can be set manually. Highest yaw band value that can be set manually (max. damping).
The AP11 will return to active mode by pressing the STBY/AUTO button, or it automatically times out after 30 seconds and returns to active mode. Sea State Filter setting is stored in the autopilot memory when power is turned off and is recalled next time the system is used.

Alarms

The software program in the AP11 is continually monitoring system input and output data as well as operational functions of the system. Audible and visual alarms are given in the event a failure is detected. The Heading Display will show a flashing FAIL whilst the Mode Display below will show an explaining text.
The audible alarm is reset by pressing the Mode button or by changing mode from e.g. AUTO to STBY. The visual alarm will now display "Err." and alternate in 3 seconds every 12 seconds with the operating display until the fault has been rectified. Consult the Trouble Shooting section, page 88 for hints and try to solve the problem yourself. If the problem turns out to be too complicated, consult your nearest Simrad Robertson dealer for assistance.

Determine system configuration
It is important to become familiar with the configuration of the system prior to beginning the installation. The diagrams presented on page 42 through page 44 provide sample system configuration drawings. With the flexibility of the AP11 system, your specific installation may include all or part of one of the sample diagrams. Try to mount the units within the standard cable length supplied with each unit.

AP11 Basic system

R 35 FC FLUXG ATE C MPAS O S AP 11 C NTR L UNIT O O
R PU80/R U160 P R EVER IBLE S P UMP S J3000X/J300X JUNCTIO N UNIT
MAINSP W S P O ER UP LY 12/24 VDC R F300 R UDDER FEEDBAC K
Figure 12 AP11 Basic System
AP11 connected to a IS11 instrument system
RFC35 FLUXGATE COMPASS J3000X JUNCTION UNIT

RPU80 REVERSIBLE PUMP

GPS SENSOR

CHART PLOTTER

WIND DATABOX SPEED DEPTH

IS11 SENSORS

IS11 INSTRUMENTS
Figure 13 AP3000X connected to an IS11 system

AP11 system with options

BO AT'S MAG NETIC CO MPAS S R 35 FC FLUXG ATE C MP S O AS

AP11 CO NTRO UNIT L

S ECO ND S TATIO N

R3000X REMOTE CONTROL

CD100 C URS O E DETECTO R
C DI35 CO SE UR DETEC R TO INTER FAC E

J3000X JUNC TIO N UNIT

NFU S TEERING LEVER
R U80 P R EVER IBLE S P UMP

PLO TTER NAV. R EIVER EC

S LENO O ID VALVE
IS C MPAS IS R 11 O S 11 UDDER INS UMENT INS UMENT TR TR LF3000 LINEAR FEEDBAC K
LFI3000 LINEAR FEED BAC K INTER FAC E
MLD200 * MECHANIC AL LINEAR DR IVE

* BUILT IN FEEDBAC K

RF300 R UDDER FEEDBAC K
HLD350 HYDR AULICLINEAR DR IVE
Figure 14 AP11 system with options
AP11 system with special J300X options

PLOTTER NAV. RECEIVER

J300X JUNCTION UNIT

RPU160 REVERSIBLE PUMP

EXTERNAL ALARM
CLOCK DATA OUTPUT FOR RADAR CHART PLOTTER

IS11 RUDDER INSTRUMENT

WIND SPEED DEPTH

IS11 COMPASS INSTRUMENT

DATABOX RF300 RUDDER FEEDBACK
HLD2000L HYDRAULIC LINEAR DRIVE
Figure 15 AP11 system with special J300X options
RF300 Rudder feedback installation
The RF300 Rudder feedback unit mounts close to the rudders, and is mechanically linked to the rudder tiller arm or rudder quadrant. Refer to figure below for the recommended mounting arrangement. Note that the RF300 transmitter arm has two slots for the transmission link. The slots enable maximum flexibility to provide the 1:1 mechanical linkage relationship.
Do not try to remove the transmitter arm from the feedback unit. The unit is factory adjusted and need no further adjustment at installation than described below. As a starting point, it is desirable to set the transmitter rod to the inner limit of the outer slot if possible. (Refer to figure). Drill and tap the rudder tiller arm so that the Y1 dimension is equal to the Y2 dimension (Use 4.2 mm drill and 5 mm tap). Attach the ball joint to the tiller arm, and connect the transmitter rod to the ball joint at the rudder tiller arm.

Grounding and RFI

The AP11 system has very good RFI protection and all units are using the Junction Unit as common ground/shield connection. The Junction Unit should therefore have a proper ground connection to the hull. ROBNET cables and other signal cables (compass, feedback, NMEA) should not be run in parallel with cables carrying RF or high current, such as VHF and SSB transmitters, battery chargers/generators and winches. Remove the bottom cover to get access to the plug-in terminals. Strip about 1 cm (0.4") of the cable's insulation and pull the screen backwards to cover the insulation. Position the straps as shown and tighten well to make sure the screen has good contact. Leave sufficient free wires so that the plug-in terminals can be easily connected/disconnected.
Main Board terminals Power Board terminals Ground terminal
Figure 19 Junction unit grounding Pull out each terminal before connecting the wires. Remove all strands before putting on the terminal cover.

Power Board terminals

TB9 and TB10 are not on the J3000X Power Board

Main Board terminals

Drive unit installation
The relation between drive units, drive unit voltage, input voltage, drive output and interfacing to steering gear are shown in the table below. The AP11 system detects whether a reversible motor or a solenoid is connected and outputs the correct drive signal automatically. Refer to the connecting diagram for the different drive units on page 51 onwards. Installation instruction for the drive units are found in the manual for the individual units.
Robertson Drive Unit type
Drive unit Input voltage voltage (Mains) 12, 24V

Drive output

Interface to steer-ing gear Hydraulic plumbing
RPU80, RPU100 12V RPU150 RPU160 (Reversible hydraulic pump) RPU200, 24V (Reversible hydraulic pump) HLD350, HLD2000/HLD2000L HLD2000D (Hydraulic linear drives) MLD200 (Mechanical linear drive) MRD100 (Reversible mechanical drive) MRD150 RPU1/RPU3 (Continuous running hydraulic pump) 12V 12V 24V 12V 12V 24V 12V 12V 24V

Revers. motor

24V 12, 24V 12, 24V 24V 12, 24V 12, 24V 24V 12, 24V 12V 24V

Robertson reversible pump
Figure 20 Reversible pump connection
Connecting a hydraulic linear drive

HYDRAULIC LINEAR DRIVE

TB1 TB2 TB3 TB4 TB5 TB6 TB7

Bypass Clutch

Single pole clutch/bypass switch
Figure 21 Hydraulic linear drive connection
Separate clutch/bypass switch
On sailboats it may be practical to install a single (or double) pole switch at the helm to be able to disengage the drive unit. Run the clutch/bypass cable via the switch to the junction unit as shown. Refer also to page 27.
Connecting a solenoid valve

SOLENOID VALVE

POWER PCB TB1 TB2 TB3 TB4 TB5 TB6 TB7

Sol. gnd

Figure 22 Solenoid valve connection
Control Unit Installation
The control unit is fully waterproof and can therefore be installed on deck or below. The connections should be protected from water penetration and should, if possible, allow rear access to remove the desiccant pack annually. The position selected should in the first instance meet the requirements of the helmsman or crew. The control unit should be at least 150 mm (6") away from a magnetic compass.
Pay particular attention to the viewing angle when installing the control unit in a dashboard or overhead. A viewing angle of min. 30 is recommended. When reading the display from the opposite position (12 oclock) the viewing angle can be reduced to 20. The selected surface must be flat and even to within 0.5 mm.

30 0.5 mm max.

Figure 23 Control unit mounting
1. Once a suitable position has been found, the installation can begin. For security reasons a note should be made of the unit serial number, and kept in a safe place. 2. Carefully position the self-adhesive template provided on the surface where the instrument is to be mounted 3. Drill a small pilot hole first and then check the location on the other side of the panel or bulkhead to confirm suitability. 53
4. Open hole out using a 50 mm (2") cutter in a hand held brace or electric drill. Drill the 4 fixing holes using a 2.5 mm (3/32") drill. 5. Connect the control unit to the Dataline wire, making sure that the colors are correctly wired to the terminals. Note that the cables should be supported with clips close to the terminal blocks. 6. Before finally fixing the instrument in position, the installation should be checked functionally. 7. If it is not possible to gain access to the instrument back when fitted, the terminals at this stage should be covered with a liberal coating of silicone grease, Vaseline, WD40 (or similar moisture dispersant). These materials will not harm any other instrument components. 8. Secure the instrument head in place using 4 No. 6 self tapping screws provided and ensure the sealing gasket is correctly located with the self-adhesive side to the location surface. DO NOT OVERTIGHTEN as the instrument can be permanently damaged if distorted tighten screws lightly and evenly. Note ! DO NOT use any form of sealing compound on the instrument back. This can damage the instrument and prevent access to the desiccant pack.

LFI3000 Mk2 additional test
1. Align engines to centre position; zero rudder. 2. Rev engines to 3-4000 rev/min and observe the rudder angle indicator on the autopilot, a 2 change in the reading should be accepted. 3. If the rudder angle exceeds 2, connect the screen on the TB1 cable to the centre block terminal (See Figure 37) and repeat item 2. If this gives a better result keep the screen connected. After the above dock-side settings are completed, the autopilot can be operated in the normal way even if some adjustments remain before the installation setup is completed. Proceed to next menu item by pressing >.

Compass setup

This menu item will set up the system to read compass heading on the Robertson two-wire format or on Robnet format. If a standard RFC35 Fluxgate compass or a magnetic compass (via CDI35 Interface) is connected, the display shall read J3. If a Robertson RFC35R Rate Compass is connected the display shall read net (Robnet). Activate the COMPASS display by pressing the MODE button. Use the < or > button to select the correct interface. Store by pressing the MODE button. Press > to proceed to next menu item.
The display will read RADAR. If your AP11 system includes a J300X (not a J3000X) Junction Unit, you have the possibility of connecting a Anritsu or a Furuno radar that do not read heading signals on NMEA format. Activate the RADAR display by pressing MODE. Use the < or > button to select Anritsu (A) or Furuno (F) type of radar. Store type of radar by pressing MODE. Press > to proceed to next menu item.

Transition speed

The display will read SPEED. The AP11 provides two different sets of steering parameters for controlling the response of the boat at different speeds (HI) or (LO) while in AUTO COM and AUTO NAV modes. The AP11 always selects the HI speed steering parameters when first switched on. This is a safety feature. After initial turn on, selection of the steering parameters is done automatically, based on the availability of input data from either an external speed log or an external navigator through the NMEA input port. GPS speed over ground may also be used if a log is not installed. However, GPS may give unstable speed information causing unwanted change of parameters. The speed at which the AP11 changes from HI to LO (or opposite) is determined by the "Transition Speed" value as set under this menu item.

Automatic tuning

The display will read AUT TUNE. Autotuning is a new dynamic function that enables the AP11 system to automatically set up the steering parameters (Rudder, Counter Rudder, Autotrim) for the boat. The scaling factors of the parameters are also set automatically as a function of the boat type selection performed in the Dockside Settings Menu. Note ! Autotune is an optional procedure that is not required for the AP11 to function. The AP11 is preset with steering parameters that should steer most boats in the 30 - 50 foot range and Autotune may not be required if the preset parameters steer your boat acceptably. Recommended speed during Autotune is 5-10 knots. Autotune should not be performed at planing speed. It is recommended that the Autotune be done in an East or West direction if possible, as these will yield the best balanced parameters.
The Autotune function will take control of the boat and perform a number of S-turns. It must always be performed in open waters with sufficient safe distance to other traffic. The Autotune function may take from 1 to 2 minutes to complete. Activate the AUT TUNE by pushing MODE, - the display will flash YES or NO. If the display reads NO, press > to acknowledge YES. Press MODE again to start the Autotune. After the Autotune is completed the display will read dONE. The rudder must be controlled manually as the mode is returned to STBY. After having performed the Autotune, there should normally be no need for further adjustments. On certain installations, however, you may want to "fine tune" the parameters after the Autotune due to the special steering characteristic of a specific boat. Viewing or changing the Autotune parameters are done from within the VIEW PARAMETERS menu item.

View parameters

A boat's steering parameters found by Autotune can be looked at and if needed changed under this menu item. The steering parameters can also be set to values manually instead of performing an Autotune. The parameters are divided into two sets: HI = Steering parameters for automatic steering at HI speed LO = Steering parameters for automatic steering at LO speed Access the View Parameter Menu as described on page 68. Press the MODE button to access the first menu item. Study the flow chart and table below for further information and follow the recommendations on the next page.

Removal of the Control Unit
To remove the control unit, the outer cover must first be removed. This can be done by squeezing the sides between finger and thumb and applying an upward pressure. At the same time place a wide bladed screwdriver between the bulkhead or panel and the cover, and gently rotate. Then remove the four fixing screws securing the head in place, and very gently lever off the head.

Junction Unit

No special maintenance is required. It is advisable, however, at the start of each season to make a visual inspection of the internal and check all connections.

Rudder Feedback

Make a visual inspection at 2-3 month intervals and at the start of each season. Apply some grease at the ball joints when required (RF300). At the start of each season also make a visual inspection of the (LFI3000) feedback interface if installed, and check the connections.

Compass

If the compass is exposed to the weather, make a visual inspection at 2-3 months intervals, and at the start of each season.

Drive unit

Refer to the drive unit manual for maintenance instructions.

Exchange of E-Prom

Junction Unit EPROM
Remove the EPROM from the socket by means of the special extraction tool (P/N 44139806) Insert the tool by pressing the two grip pins down into the two slots in the corners of the socket. Squeeze the tool and pull out the EPROM. When inserting new EPROMS, make sure the cut-off corner matches with the one in the socket. Press it gently into the socket. The identification tag indicates: - Name of unit - Robertson part number - Software version EPROM for J300X and J3000X Junction units: - P/N 22081640 Cut-off corner
Grip pins Identification tag
After change of EPROM, perform a master reset as described on page 75.

TROUBLE SHOOTING

An autopilot is a complex system and the performance is dependent of a proper installation and a successful sea trial. In the event of a failure, you will be helped by the AP11 software which contains several test features that will assist you in isolating a probable fault.

Display OFF CRS.

Alarm listing
Probable fault Off course alarm Limits: 20 on compass, 5 on wind Compass failure Rudder feedback failure Drive unit failure Recommended action Check steering parameters (View Parameters Menu page 80).Check boat trim, adjust trim flaps or sails. Check connections, cable and heading sensor. Check cable, connections and installation of Rudder Feedback Unit Check connections to drive unit motor and clutch or bypass valve. Verify that motor is running, and the clutch or bypass clicks in and out. Also check that the mechanical or hydraulic hand steering works properly and that the rudder moves smoothly. Consult the drive unit manual. Check that the "NMEA talker" is powered up and configured for transmitting data to the autopilot. The LEDs in the junction unit will flicker if data is present on RX port. Check connections, cables and switches on data source. Run NMEA check in installation setup to analyze incoming data. Also check Nav. receiver setup for: waypoints, route, magnetic variation, arrival alarm etc.

Data input check

CROSS TRACK ERROR

BEARING WP - WP

WIND APPARENT (VWR MESSAGE)

SPEED OVER GROUND

WATER SPEED

LOOPBACK TEST PORT NO. 1

LOOPBACK TEST PORT NO. 2
Each menu item will show one of the following status codes: --OK INV FRM NO DATA Valid data received Invalid data received Format failure, or wrong check sum received
If any of the displayed status codes are different from OK, the most probable reason is erratic or missing data from the data source, i.e. Nav. receiver, plotter, wind sensor or log. Check the individual equipment for correct set-up prior to consulting your Simrad Robertson dealer for assistance.

Hardware check

To confirm that the NMEA hardware of the Junction Unit is O.K., it is possible to make a loop-back test. Connect TX1+ to RX1+ and TX1- to RX1- for port no. 1 (J3000X) and similar for port no. 2 (J300X). The display will give the message "OK" if hardware is O.K. and "--" if something wrong. If a Dataline Databox is connected to one of the ports, it will automatically do a loopback test without any hardwiring.

Signal monitor

On the Junction unit input it is possible to monitor the incoming signal by observing corresponding "RX" LED on the input circuit. Port 1 on Main Board, port 2 (J300X) on Power Board. Flickering LED indicates that signal is received. However, there may still be a problem with baudrate, polarity and stop bits.
The Junction unit also has a NMEA "TX" LED that will flicker whenever the autopilot is on. (Sending heading and rudder angle data.) Make sure this "TX" LED is not mixed up with the "RX" LED when checking for incoming data. Press > to proceed to the System Status check.

System status

XX - Power Board Revision YY - Main Board Revision
The system state feature allows you to read the software version of the control unit and the junction unit and also the revision of the Power Board and the Main Board in the junction unit. Activate the SYS STAT display by pushing MODE once. Step through the display readings by pushing < or >.

Operation: 10 to +55C (+14 to +130F) Storage: 30 to +80C (22 to + 176F)
Stroke:... 300 mm Operating principle:.. Variable differential transformer, excitation and signal conversion by separate LFI3000 Interface unit Power:.. Supplied by LFI3000 Dimensions:.. 465 mm (18,3") x 22 (0,86") dia. Mounting:. Clamped to hydraulic ram Material:.. Rod: Stainless Tube: Epoxy coated sea water resistant aluminium Environmental protection:.. IP67
LFI3000 Mk2 Feedback Interface
Supply:... From Junction Unit Output signal:.. Polarity independent variable frequency Frequency resolution. Center 3400Hz, 20Hz/degree equal to 1,7 mm travel Linearity:.. 3 degrees up to 45 degrees of rudder Cable supplied:.. 1,5 m TP shielded cable Dimensions:.. 128 x 102 x72 mm (5.0 x 4.0 x 2.8 in.) Weight:.. 0,7 kg including cable (1,6 lbs.)
Power consumption:.. 0,9 watts Temperature range:
AP11 AUTOPILOT SPARE PARTS LIST
AP11 Control unit AP11 Control unit with installation accessories AP11 Control unit Installation accessories Front cover Cap strip digital buttons Seal plug, back plate Protection cover 7 m cable, (3xTP, shielded) Screws no. 6 self-tapping( 4 ea.) Template Junction Units J300X Junction unit with installation accessories J300X Junction unit (only) Installation accessories J300X Power PCB assy. J300X Main PCB assy. EPROM for J300X/J3000X Base plate Main cover Terminal cover J3000X Junction unit with installation accessories J3000X Junction Unit (only) Installation accessories J3000X Power PCB assy. J300X Main PCB assy.

22081442

EPROM for J300X/J3000X Base plate Main cover Terminal cover RFC35 Fluxgate Compass RFC35 Fluxgate Compass with installation accessories RFC35 Fluxgate Compass (only) Installation accessories consisting of: 20104972 Mounting bracket (2 ea.) 44140762 Screw 3.5x25 (4 ea.) 44140770 Screw 30x9 (2 ea.) 22081376 Plug (4 ea.)

22081178

RFC35 PCB assy. RF300 Rudder Feedback Unit

20193470 20193624

RF300 Rudder Feedback with transmission link RF300 Rudder Feedback RF300 transmission link Transmission rod M5x325mm RF300 Transmission lever RF300 Ball joint ass'y

SPARE PARTS RICE LIST

SIMRAD PRODUCTS
Navico Egersund 20237780/A English

Navico Egersund

Modification record
The price list is dynamic, and changes may occur. In event of changes to this price list, the following modification record should be filled in.

17.01.2007

Comments

First issue

20237780 / A
Spare Parts Price List 2007
Obsolete Products (omitted from Price List)
Product Autopilots AP300 AP300DL AP300P AP300X AP300DLX AP300PX AP9 Adaptive MC9/MC100 Interface Units CI300X G40A G45 RGC Signal Interface Unit TI50 Feedback Units RF100 RF300S RF45 RF14XI LFI3000 Fluxgate Compasses RFC250 RFC300 Gyro Compasses RGC10 RGC11 RGC12 Rudder Angle Indicators RI40 RI45 RI35 Panorama Panorama I Remote Controls F200 FU35 S100 F1/2 JP300 Drive Units HLD350 HLD2000 RPU100 RPU200 Substitute No No No AP22 AP20 AP21 No No GI51 GI51 GI51 GI51 TI51 No RF300 RF45X No LFI3000Mk2 RFC35NS RFC35N GC80/85 GC80/85 GC80/85 RI9 RI9 RI35Mk2 Panorama Mk2 No No FU50 JS10 No JP21 HLD350Mk2 HLD350Mk2 RPU80/160 RPU300, 24V RF45X may be used RF300 Product code FA or higher RF45X may be used Comments
Parts on request Parts on request

Wired for Robnet

(Panorama Mk2 + RF14XU)

(R3000X may be used)

Alt. HLD2000Mk2L

Contents

IS15 INSTRUMENTS... 1 AP11 AUTOPILOT.. 4 AP20 AUTOPILOT.. 4 AP21 AUTOPILOT.. 4 ROBNET CABLES AND CONNECTORS:.. 4 AP22 AUTOPILOT.. 5 AP16 AUTOPILOT.. 5 AP25 AUTOPILOT.. 5 AP26 AUTOPILOT.. 5 AP27 AUTOPILOT.. 6 TI25 THRUSTER INTERFACE.. 6 TOOLS.... 6 ROBNET2 CABLES... 6 SimNet CABLES AND ACCESSORIES.. 6 AUTOPILOT COMPUTERS.. 7 JUNCTION UNITS.. 8 AP35 AUTOPILOT.. 9 AP45 AUTOPILOT... 10 AP50 AUTOPILOT... 11 AP9MK3/MKII AUTOPILOT.. 12 FUA9X FOLLOW-UP AMPLIFIER.. 13 FEEDBACK UNITS... 14 HEADING SENSORS... 15 RUDDER ANGLE INDICATORS... 17 REMOTE CONTROLS... 17 DRIVE UNITS... 19 RGC50 GYRO COMPASS... 22 RGC10 GYRO COMPASS... 24 RGC11 GYRO COMPASS... 26 RGC12 GYRO COMPASS... 29 GC80/GC85 GYRO COMPASS (MASTER COMPASS).. 30 GYRO REPEATERS... 32 CHART SYSTEM... 33 ROBERTSON MULTIPURPOSE PILOT... 36
Spare Parts Price List 2005
AC10..7 AC20..7 AC40..7 AD50..11 ADP600..36 AP11..4 AP16..5 AP20..4 AP21..4 AP22..5 AP25..5 AP26..5 AP27..6 AP35..9 AP45..10 AP50..11 AP51..11 AP9 ADAPTIVE..13 AP9MK3/MKII..12 AR68..32 AR77..32 AR78..32 AR80..32 AUTOPILOT COMPUTERS..7 FU50.. 19 FU91.. 18 FUA9X.. 13
R3000X.. 17 RC25... 16 RC36... 16 RC37... 16 REMOTE CONTROLS.. 17 RF14XU... 14 RF300.. 14 RF45X.. 14 RFC35.. 15 RFC35N... 15 RFC35NS.. 15 RFC35R... 15 RFC35RS.. 15 RFC35SIN.. 15 RGC BEARING REPEATER. 32 RGC SIGNAL INTERFACE UNIT.. 32 RGC10.. 24 RGC11.. 26 RGC12.. 29 RGC50.. 22 RI35 MK2.. 17 RI9.. 17 RMP.. 36 ROBERTSON MULTIPURPOSE PILOT... 36 ROBFISH.. 36 ROBNET CABLES. 4 ROBNET2 CABLES.. 6 RPU160... 19 RPU200... 19 RPU300... 20 RPU80.. 19 RUDDER ANGLE INDICATORS.. 17
G40A... 10 G45.. 10 GC80... 30 GC85... 30 GI50.. 11 GI51.. 11 GYRO COMPASS. 22 GYRO REPEATERS. 32
HEADING SENSORS.. 15 HLD2000.. 20 HLD2000 MK2.. 20 HLD350... 21

IS15.. 1

J3000X.. 8 J300X.. 8 J300X-40.. 8 J45A.. 8 J45S.. 8 J50.. 9 JP21.. 4 JS10.. 17 JUNCTION UNITS. 8
CD100A...16 CD109..16 CDI35..16 CHART SYSTEMS.33 CI300X..9 COP..35 CS55..33 CS56..33 CS65..33 CS66..34

LFI3000 MK2. 14

MC100.. 13 MC30... 33 MC50... 35 MC9.. 13 MLD200... 21 MSD50.. 22
S35.. 18 S9.. 18 SIMNET CABLES. 6 SJS500.. 36 STS500.. 36
D90-D93..13 DD15...21 DR75..32 DR76..32 DRIVE UNITS.19
F1/2..19 F200-40...18 FEEDBACK UNITS..14 FU25..18

NI300X.. 9

TI25.. 6 TI50.. 11 TI51.. 11 TOOLS.. 6

PANORAMA MK2. 17

Spare Parts Price List 2007 PART NO. DESCRIPTION REFERENCE

IS15 INSTRUMENTS

22094734 22094734
IS15 COMBI INSTRUMENT W/ACCESSORIES EXCH: IS15 COMBI INSTRUMENT W/ACC. IS15 COMBI PROM (PROGRAMMED) V.R. IS15 MULTI INSTRUMENT W/ACCESSORIES EXCH: IS15 MULTI INSTRUMENT W/ACC. IS15 MULTI PROM (PROGRAMMED) V.R. IS15 COMPASS INSTRUMENT W/ACCESSORIES EXCH: IS15 COMPASS INSTRUMENT W/ACC. IS15 COMPASS PROM (PROGRAMMED) V.R. IS15 WIND INSTRUMENT W/ACCESSORIES EXCH: IS15 WIND INSTRUMENT W/ACC. IS15 WIND PROM (PROGRAMMED) V.R. IS15 TACK INSTRUMENT W/ACCESSORIES EXCH: IS15 TACK INSTRUMENT W/ACC. IS15 TACK PROM (PROGRAMMED) V.R. IS15 RUDDER INSTRUMENT W/ACCESSORIES EXCH: IS15 RUDDER INSTRUMENT W/ACCESSORIES IS15 RUDDER PROM (PROGRAMMED) V.R. IS15 SERVICE KIT (screws, corners, gasket) IS15 PROTECTION COVER IS15R COMBI INSTRUMENT W/ACCESSORIES EXCH: IS15R COMBI INSTRUMENT W/ACC. IS15 COMBI PROM (PROGRAMMED) V.R. IS15R MULTI INSTRUMENT W/ACCESSORIES EXCH: IS15R MULTI INSTRUMENT W/ACC. IS15 MULTI PROM (PROGRAMMED) V.R. IS15R COMPASS INSTRUMENT W/ACCESSORIES EXCH: IS15R COMPASS INSTRUMENT W/ACC. IS15 COMPASS PROM (PROGRAMMED) V.R. IS15R WIND INSTRUMENT W/ACCESSORIES EXCH: IS15R WIND INSTRUMENT W/ACC. IS15 WIND PROM (PROGRAMMED) V.R. IS15R TACK INSTRUMENT W/ACCESSORIES EXCH: IS15R TACK INSTRUMENT W/ACC. 1

Navico Egersund PART NO. 22093777 DESCRIPTION IS15 TACK PROM (PROGRAMMED) V.R. IS15R SERVICE KIT (screws, gaskets, snap on ring) IS15 WIND TRANSDUCER W/ BRACKET AND CABLE IS15 WIND TRANSDUCER ONLY EXCH: IS15 WIND TRANSDUCER ONLY IS15 WIND TRANSDUCER BRACKET AND CABLE IS15 WIND TRANSDUCER CUPS ASS'Y * REPLACEMENT OF VANE ASS'Y REQUIRES NEW FACTORY CALIBRATION WIND TRANSDUCER CALIBRATION + VANE IS15 TRANSCEIVER WITH ACCESSORIES EXCH: IS15 TRANSCEIVER WITH ACCESSORIES IS15 TRANSCEIVER PCB ASS'Y EXCH: IS15 TRANSCEIVER PCB ASS'Y IS15 EXPANDER WITH ACCESSORIES EXCH: IS15 EXPANDER WITH ACCESSORIES IS15 EXPANDER PCB ASS'Y EXCH: IS15 EXPANDER PCB ASS'Y IS15 POWER SUPPLY WITH ACCESSORIES IS15 POWER SUPPLY PCB ASS'Y EXCH: POWER SUPPLY PCB ASS'Y ROBLINK CABLES ROBLINK CABLE 0,3M ROBLINK CABLE 2M (6,5') ROBLINK CABLE 5M (16,5') ROBLINK CABLE 10M (33') ROBLINK POWER CABLE 2,5M (8') ROBLINK CABLE ADAPTER/"JOINER", 5PCS. TRANSDUCERS PLEASE REFER TO MAIN PRICE LIST FOR COMPLETE UNITS 44169720 FAIRING FOR B44V HIGH SPEED FAIRING FOR B744V PADDLE WHEEL & VALVE KIT FOR P17, ST650/SS557 PADDLE WHEEL KIT FOR ST610,B744V, B44V (33-250) PADDLE WHEEL KIT FOR P52 PADDLE WHEEL & VALVE KIT, ST610 (33-113) FAIRING FOR SS505 TYPE 33-160 REFERENCE
Spare Parts Price List 2007 PART NO. DESCRIPTION HIGH SPEED FAIRING FOR B45 TRANSDUCER CABLE TYPE C2 (DEPTH) PRICE PER 5 M TRANSDUCER CABLE TYPE C9 (SPEED/TEMP) PRICE PER 5 M TRANSDUCER CABLE TYPE C32 (TRIDUCER) PRICE PER 5 M B44V S/T INSERT ST650 S/T INSERT ST650 SEA VALVE ASS'Y ST650 BLANKING PLUG 20-602 ST650/B17 HOUSING & NUT 33-100 PLASTIC HOUSING ASS'Y (FOR ST610) STAINLESS STEEL HOUSING (SS557/ST650) ST610 S/T INSERT REFERENCE
Navico Egersund PART NO. DESCRIPTION REFERENCE

AP11 AUTOPILOT

AP11 CONTROL UNIT EXCH: AP11 CONTROL UNIT FRONT COVER (CLIP-ON BEZEL) PROTECTION COVER

22084750 22084834

AP20 AUTOPILOT
AP20 CONTROL UNIT EXCH: AP20 CONTROL UNIT AP20 MOUNTING KIT (screws, gaskets, corners) AP20 OPTIONAL MOUNTING BRACKET KIT AP20 FRONT HOUSING ASS'Y BACK COVER WITH GASKET AP20 PCB ASS'Y EXCH: AP20 PCB ASS'Y PROTECTION COVER PROM (PROGRAMMED) V.R.

22086193

AP21 AUTOPILOT
AP21 CONTROL UNIT EXCH: AP21 CONTROL UNIT AP21 MOUNTING KIT AP21 FRONT ASS'Y AP21 PCB ASS'Y EXCH: AP21 PCB ASS'Y AP21 CONTROL UNIT CABLE incl. gasket ass'y AP21/AP22 PROM (PROGRAMMED) V.R. AP21 BACK COVER

22086557

JP21 JACK POINT JP21 COVER ASS'Y & O-RING

44139806

ROBNET CABLES AND CONNECTORS:
ROBNET ROBNET ROBNET ROBNET ROBNET ROBNET ROBNET ROBNET
CABLE 7 METER CABLE 15M WITH 2 MALE CONNECTORS EXT. CABLE 10M MALE/FEM CABLE 15M WITH 1 MALE CONNECTOR MALE CONNECTOR ASS'Y FEMALE CONNECTOR ASS'Y PCB CONNECTOR 180 DGR. PCB CONNECTOR 90 DGR.
Interface Units Control Units

44155737

20213773 20213773

20212189

AP50 AUTOPILOT
AP50 CONTROL UNIT W/ACCESSORIES EXCH: AP50 CONTROL UNIT W/ACCESSORIES INSTALLATION ACCESSORIES (screws, gasket, corners) AP50 MOUNTING BRACKET ASS'Y PROTECTION COVER AP50 FRONT HOUSING ASSY AP50 BOARD ASS'Y EXCH: AP50 BOARD ASS'Y AP50 EPROM (PROGRAMMED) V.R. AP51 REMOTE CONTROL AP51 REMOTE CONTROL W/ACCESSORIES EXCH: AP51 REMOTE CONTROL W/ACCESSORIES AP51 BOARD ASS'Y EXCH: AP51 BOARD ASS'Y AP51 FRONT HOUSING ASS'Y BACK COVER CONTROL UNIT CABLE WITH GASKET AP51 PROM (PROGRAMMED) V.R. MOUNTING KIT TI50 THRUSTER INTERFACE SUBSTITUTED BY TI51 THRUSTER INTERFACE TI51 THRUSTER INTERFACE EXCH: TI51 THRUSTER INTERFACE TI51 PCB ASS'Y EXCH: TI51 PCB ASS'Y PROM (PROGRAMMED) V.R. ROBNET CABLES AND CONNECTORS; SEE PAGE 4 AD50 ANALOG DRIVE AD50 ANALOG DRIVE EXCH: AD50 ANALOG DRIVE AD50 PCB ASSY EXCH: AD50 PCB ASSY PROM (PROGRAMMED) V.R. GI50 GYRO INTERFACE SUBSTITUTED BY GI51 GYRO INTERFACE GI51 GYRO INTERFACE GI51 GYRO INTERFACE EXCH: GI51 GYRO INTERFACE 11

22086276

22089460

20213104

Navico Egersund PART NO. 20213815 DESCRIPTION GI51 PCB ASS'Y EXCH: GI51 PCB ASS'Y GI51 SOFTWARE PROGRAMMING KIT RS232 PENDULUM FUNCTION KEY ROBNET CABLES AND CONNECTORS; SEE PAGE 4 REFERENCE PRICE

Net price

20168316 20168316

AP9MK3/MKII AUTOPILOT

AP9MK3 CONTROL UNIT W/ACCESSORIES EXCH: AP9MK3 CONTROL UNIT MOUNTING KIT EMC KIT TYPE 9 AP9MK3 FRONT HOUSING ASS'Y (WITHOUT DISPLAY BOARD) EXCH: AP9MK3 FRONT HOUSING ASS'Y AP9MK3 FRONT PANEL KEYPAD COURSE SELECTOR KNOB ASS'Y COURSE SELECTOR TOOTH WHEEL AP9MK3 COURSE DISPLAY GLASS AP9MK3 INFO DISPLAY GLASS AP9MK3/MKII DISPLAY PCB ASS'Y EXCH: AP9MK3/MKII DISPLAY PCB ASS'Y FOR AP9MK3: PCB REV. B ONWARDS DISPLAY LCD 4-DIGITS 3/4" ILLUMIN.STRIP NEL 5L-384-C DISPLAY MODUL LM16255M BARGRAPH DISPLAY ILLUMIN STRIP NEL 5L-383-C AP9MK3/MKII FRONT PCB ASS'Y EXCH: AP9MK3/MKII FRONT PCB ASS'Y FOR AP9MK3: PCB REV. M ONWARDS AP9MK3 IC PROGRAMMED V1R4 AP9MK3/MKII INTERFACE PCB ASS'Y EXCH: AP9MK3/MKII INTERF. PCB ASS'Y FOR AP9MK3: PCB REV. L ONWARDS AP9 ANALOG OPTION KIT AP9MK3/MKII GYRO I/F PCB ASS'Y EXCH: AP9MK3/MKII GYRO I/F PCB ASS'Y FOR AP9MK3: PCB REV. B ONWARDS

LCD3 EL3 LCD1 LCD2 EL2

Spare Parts Price List 2007 PART NO. 44155240 DESCRIPTION D90-D93 DISTRIBUTION UNITS D9X POWER SUPPLY PCB ASS'Y EXCH: D9X PS PCB ASS'Y D9X INTERCONN. PCB ASS'Y EXCH: D9X INTERCONN. PCB ASS'Y D9X SOLID STATE PCB ASS'Y 24VDC EXCH:D9X SOL.STATE PCB ASS'Y 24VDC D9X SOLID STATE PCB ASS'Y110VDC EXCH:D9X SOL.STATE PCB ASS'Y 110VDC D9X SOLID STATE PCB ASS'Y 220VAC EXCH:D9X SOLID STATE PCB ASS'Y 220VAC D9X DUAL ANALOG PCB ASS'Y EXCH: D9X DUAL ANALOG PCB ASS'Y D9X THRUSTER INTERFACE PCB ASS'Y EXCH:D9X THRUSTER I/F PCB ASS'Y D9X OPTO PCB ASS'Y EXCH: D9X OPTO PCB ASS'Y ISOLATION AMPLIFIER (DUAL ANALOG PCB) BUS CABLE SOLID STATE RELAY 24V DC SOLID STATE RELAY 110V DC SOLID STATE RELAY 220V AC D90 D91 D92 REFERENCE
AP9 ADAPTIVE AUTOPILOT: PARTS ON REQUEST MC100 MAIN COMPUTER: PARTS ON REQUEST MC9 MAIN COMPUTER: PARTS ON REQUEST

23602857

FUA9X FOLLOW-UP AMPLIFIER
FUA9X FOLLOW-UP AMPLIFIER PCB ASS'Y EXCH: FUA9X PCB ASS'Y D9X SOLID STATE PCB ASS'Y 24VDC EXCH:D9X SOL.STATE PCB ASS'Y 24VDC D9X SOLID STATE PCB ASS'Y 110VDC EXCH:D9X SOL.STATE PCB ASS'Y 110VDC D9X SOLID STATE PCB ASS'Y 220VAC EXCH:D9X SOLID STATE PCB ASS'Y 220V D9X INTERCONN. PCB ASS'Y EXCH: D9X INTERCONN. PCB ASS'Y D9X DUAL ANALOG PCB ASS'Y EXCH: D9X DUAL ANALOG PCB ASS'Y D9X POWER SUPPLY PCB ASS'Y EXCH: D9X PS PCB ASS'Y BUS CABLE

FEEDBACK UNITS

44118388
RF14XU RUDDER FEEDBACK UNIT RF14XU RUDDER FEEDBACK UNIT EXCH: RF14XU RUDDER FEEDBACK UNIT RF STANDARD TRANSMISSION LINK BALL JOINT 8MM, STAINLESS STEEL TRANSMISSION LEVER 12MM ELECTRONIC XU MODULE POTENTIOMETER (SINGLE) 5K) RF45X RUDDER FEEDBACK UNIT RF45X RUDDER FEEDBACK EXCH: RF45X RUDDER FEEDBACK RF45X PCB ASS'Y W/POTMETER EXCH: RF45X PCB ASS'Y POTMETER 10K (WITH WIRES) JUNCTION BOX (HENSEL D1202) RF45 TRANSMISSION LINK ASS'Y RF45 BALL JOINT ASS'Y TRANSMISSION LEVER RF300 RUDDER FEEDBACK UNIT RF300 RUDDER FEEDBACK UNIT RF300 TRANSMISSION LINK ASS'Y RF300 TRANSMISSION LEVER ASS'Y RF300 BALL JOINT ASS'Y LF3000 LINEAR FEEDBACK LF3000 LINEAR FEEDBACK LF3000 MOUNTING KIT EXCH: LF3000 LINEAR FEEDBACK LF3000 COIL CORE LF3000 SEASTAR KIT LFI3000 MK2 INTERFACE SUBSTITUTES LFI3000 EXCH. LFI3000 MK2 INTERFACE LFI3000 MK2 BOARD ASS'Y SUBSTITUTES LFI3000 BOARD ASS'Y EXCH: LFI3000 MK2 BOARD ASS'Y

22504039

20193678 20193624

20187928

HEADING SENSORS
RFC35 FLUXGATE COMPASS RFC35 FLUXGATE COMPASS W/ Acc. EXCH: RFC35 FLUXGATE COMPASS W/ Acc. RFC35 PCB ASS'Y (MOTHER BOARD) EXCH: RFC35 PCB ASS'Y (MOTHER BOARD) RFC35R RATE COMPASS NOTE: SUBSTITUTED BY RC25 EXCH: RC25 RATE COMPASS W/ Acc. (REPLACEMENT FOR EXCH: RFC35R COMPLETE) RFC35 PCB ASS'Y (MOTHER BOARD) EXCH: RFC35 PCB ASS'Y (MOTHER BOARD) RFC35 RATE UPGRADE KIT (AVAILABLE ON REQUEST) RFC35R PCB ASS'Y (AVAILABLE ON REQUEST) EXCH: RFC35R PCB ASS'Y (AVAILABLE ON REQUEST) RFC35R MICROCONTROLLER V2R4 RFC35N NMEA COMPASS RFC35N W/ACCESSORIES EXCH. RFC35N W/ACCESSORIES RFC35 PCB ASS'Y (MOTHER BOARD) EXCH: RFC35 PCB ASS'Y (MOTHER BOARD) RFC35N PCB ASS'Y EXCH: RFC35N PCB ASS'Y RFC35NS NMEA/SIN COMPASS RFC35NS COMPASS W/ACCESSORIES EXCH. RFC35NS W/ACCESSORIES RFC35 PCB ASS'Y (MOTHER BOARD) EXCH: RFC35 PCB ASS'Y (MOTHER BOARD) RFC35N PCB ASS'Y EXCH: RFC35N PCB ASS'Y RFC35 SIN PCB ASS'Y EXCH: RFC35 SIN PCB ASS'Y RFC35NS CABLE 0.3M RFC35RS RATE + SIN/COS COMPASS W/ACC. NOTE: SUBSTITUTED BY RC37 EXCH: RC37 RATE COMPASS W/ ACC. (REPLACEMENT FOR EXCH: RFC35RS COMPLETE) RFC35 PCB ASS'Y (MOTHER BOARD) EXCH: RFC35 PCB ASS'Y (MOTHER BOARD) RFC35R PCB ASS'Y (AVAILABLE ON REQUEST)

22084149

22082499 22082499

22083661

22081178 22082374
Navico Egersund PART NO. DESCRIPTION EXCH: RFC35R PCB ASS'Y (AVAILABLE ON REQUEST) RFC35SIN PCB ASS'Y EXCH: RFC35SIN PCB ASS'Y RFC35R MICROCONTROLLER V2R4 RC36 RATE COMPASS RC36 RATE COMPASS W/ Acc. EXCH: RC36 RATE COMPASS W/ Acc. RC36 PCB ASS'Y EXCH: RC36 PCB ASS'Y RC37 RATE COMPASS NMEA - SIN RC37 RATE COMPASS W/ACCESSORIES EXCH. RC37 RATE COMPASS W/ACCESSORIES RC37 PCB ASS'Y EXCH: RC37 PCB ASS'Y RC25 RATE COMPASS RC25 RATE COMPASS W/ Acc. EXCH: RC25 RATE COMPASS W/ Acc. RC25 PCB ASS'Y (MOTHER BOARD) EXCH: RC25 PCB ASS'Y COURSE DETECTORS CD100A COURSE DETECTOR CD100A CABLE, 7M CD109 COURSEDET. W/ HOLDER COURSE DETECTOR TRIPOD HOLDER AMP CONNECTOR W/ BRACKET CDI35 INTERFACE UNIT W/Acc EXCH: CDI35 INTERFACE UNIT W/Acc CDI35 PCB ASS'Y EXCH: CDI35 PCB ASS'Y REFERENCE

22086938 22086938

22084396 22084396

22084370 22084370

22081152

22060966 22060966

RUDDER ANGLE INDICATORS
PANORAMA MK2 RUDDER ANGLE INDICATOR (45-0-45) EXCH. PANORAMA MK2 RUDDER ANGLE INDICATOR

22083992 22083968

RI35 MK2 RUDDER ANGLE INDICATOR RI35 MK2 RUDDER ANGLE INDICATOR EXCH: RI35 MK2 RUDDER ANGLE INDICATOR RI35 MK2 METER AND BOARD ASS'Y RI35 MK2 FRONT HOUSING RI35 MK2 BACK COVER RI35 MK2 FRONT PANEL RI9 RUDDER ANGLE INDICATOR RI9 RUDDER ANGLE INDICATOR EXCH: RI9 RUDDER ANGLE INDICATOR RI9 PCB ASS'Y EXCH: RI9 PCB ASS'Y INSTRUMENT, 45 DEG. SCALE LAMP BI-PIN 12V 40MA (5 pcs.) DIMMER POTENTIOMETER 4,7 K RI9 FRONT PANEL RI9 FRONT HOUSING INSTRUMENT SCALE 60 DEGREES: ON REQUEST INSTRUMENT SCALE 70 DEGREES. ON REQUEST INSTRUMENT SCALE 90 DEGREES: ON REQUEST

22015697 22015705

REMOTE CONTROLS
JS10 JOYSTICK JS10 JOYSTICK JOYSTICK, 2 POSITION JS10 MOUNTING PLATE SWITCH JS10 CABLE, 10 M JS10 RUBBER COLLAR R3000X REMOTE CONTROL R3000X REMOTE CONTROL R2500 MOUNTING KIT R2500 PCB ASS'Y R2500 CABLE R2500 FRONT HOUSING R3000X FRONT PANEL

20184586 22022396

Navico Egersund PART NO. 20171328 DESCRIPTION F200-40 REMOTE CONTROL F200-40 REMOTE CONTROL W/ACCESSORIES EXCH: F200-40 REMOTE CONTROL F100-40 CABLE, 7M W/AMP CONN. F200 PCB COMPLETE EXCH: F200 PCB ASS'Y LCD DISPLAY 4 DIGITS 0.5" CONTROL KNOB ASS'Y COURSE SELECTOR SHAFT ASS'Y F200 FRONT PANEL S9 STEERING LEVER S9 STEERING LEVER S9 HOUSING S9 BACK COVER S9 HANDLE ASS'Y S9 SERVICE KIT (Springs & grease) FU91 STEERING LEVER FU91 STEERING LEVER FU91 FRONT PANEL 45 DEG. FU9X PCB ASS'Y EXCH: FU9X PCB ASS'Y DIMMER POTENTIOMETER, 4,7K POTMETER BOURNS, 10K FU91/92 PTTC SWITCH ASS'Y S35 STEERING LEVER S35 STEERING LEVER W/ ACC. S35 PCB ASS'Y HANDLE S35 BUTTON & COVER S35 SERVICE KIT (Spring, switch, seal) FU25 FOLLOW-UP STEERING LEVER FU25 STEERING LEVER WITH ACCESSORIES EXCH: FU25 STEERING LEVER FU25/50 MOUNTING KIT (Srews and handle) ROTARY KNOB ASS'Y FU25 FRONT PANEL FU25 CABLE ROBNET2, 15 m POTENTIOMETER (10K) WITH BRACKET AND WIRES FU25 BOARD ASSY EXCH: FU25 BOARD ASSY REFERENCE

23602089

23603277

23241243

20213948
Spare Parts Price List 2007 PART NO. DESCRIPTION FU35 FOLLOW-UP STEERING LEVER SUBSTITUTED BY FU50 EXCH: FU50 STEERING LEVER FU50 FOLLOW-UP STEERING LEVER FU50 STEERING LEVER WITH ACCESSORIES EXCH: FU50 STEERING LEVER FU25/50 MOUNTING KIT (Srews and handle) ROTARY KNOB ASS'Y FRONT PANEL POTENTIOMETER (10K) WITH BRACKET AND WIRES FU50 BOARD ASSY EXCH: FU50 BOARD ASSY F1/2 REMOTE CONTROL F1/2 SPRING LEAF KIT REFERENCE

20214037

20212288 20212288

23020233

DRIVE UNITS

21118617

RPU80 REVERSIBLE PUMP UNIT RPU80 REVERSIBLE PUMP UNIT EXCH: RPU80 REVERS. PUMP UNIT RPU80 LEMAC MOTOR 12V (SUBSTITUTES RPU80 FRACMO MOTOR 12V) BRUSH LEMAC C8386 9x6x18,2MM (PAIR) BRUSH FRACMO CBC 188, 7,2x6,5x10MM (PAIR) BRUSHES FOR RPU100 AND RPU200 BRUSH FRACMO CB156, 6x10x20MM (PAIR) BRUSH FRACMO CB174, 6x10x20MM (PAIR)

21118641 21118658

SPADE RECEPTACLE

44177525

21118666 21118633
RPU160 REVERSIBLE PUMP UNIT RPU160 REVERSIBLE PUMP UNIT EXCH: RPU160 REVERS. PUMP UNIT RPU160 LEMAC MOTOR (SUBSTITUTES 44140739 RPU160 FRACMO MOTOR) BRUSH LEMAC C8386 9x6x18,2MM (PAIR) BRUSH FRACMO CBC 196, 7,2x6,5x10MM (PAIR) RPU200 REVERSIBLE PUMP UNIT SUBSTITUTED BY RPU300 24V (21118476) RPU200 MOTOR FRACMO 24V (SUBSTITUTED BY RPU300 LEMAC MOTOR 24V 44169993) BRUSH FRACMO CB156, 6x10x20MM (PAIR) BRUSH FRACMO CB174, 6x10x20MM (PAIR)

21118682

RPU300 REVERSIBLE PUMP UNIT RPU300 REVERSIBLE PUMP UNIT 12V RPU300 REVERSIBLE PUMP UNIT 24V EXCH: RPU300 REVERSIBLE PUMP UNIT 12V EXCH: RPU300 REVERSIBLE PUMP UNIT 24V RPU300 LEMAC MOTOR 12V (SUBSTITUTES 44140747 RPU300 FRACMO MOTOR 12V) RPU300 LEMAC MOTOR 24V (SUBSTITUTES 44141141 RPU300 MOTOR FRACMO 24V) BRUSH FRACMO CBC 192, 12,7x6,3X19MM (PAIR) RPU300 LEMAC BRUSH, SHORT TYPE 12,7x7,94x12MM (PAIR) RPU300 LEMAC BRUSH, LONG TYPE 12,7x7,94x19MM (PAIR) RPU 80/160/300 SEAL KIT UNC FITTINGS FOR RPU80/160/300 EU TYPE FITTING KIT, UNC ( 3 PCS.) US TYPE FITTING KIT, UNC ( 3 PCS.) RPU ADAPTER FITTING 7/16" UNC-1/4" NPT (3 PCS.) HLD2000 HYDRAULIC LINEAR DRIVES; SUBSTITUTED BY; HLD350/HLD2000 MK2 HYDRAULIC LINEAR DRIVES EXCHANGE HLD2000MK2L HLD EMERG.RELEASE PIN ASS'Y RPU160 LEMAC MOTOR (SUBSTITUTES RPU100 FRACMO MOTOR 12V) BRUSH LEMAC C8386 9x6x18,2MM (PAIR) BRUSH FRACMO CB156, 6x10x20MM (PAIR) BRUSH FRACMO CB174, 6x10x20MM (PAIR) HLD2000S FLEXIBLE HOSES ASS'Y RPU300 LEMAC MOTOR 24V (SUBSTITUTES RPU200 MOTOR 24V) RPU300 LEMAC BRUSH, SHORT TYPE 12,7x7,94x12MM (PAIR) RPU300 LEMAC BRUSH, LONG TYPE 12,7x7,94x19MM (PAIR) BRUSH FRACMO CBC 192, 12,7x6,3X19MM (PAIR) HLD2000 SEAL KIT, COMPL. HLD2000 MK2 PUMP AND MOTOR ASS'Y HLD2000 MK2 SEAL KIT, COMPL. RPU 80/160/300 SEAL KIT HLD350/2000 MK2 HYDR.CYLIND. ASS'Y

20997953

21101415
Spare Parts Price List 2007 PART NO. DESCRIPTION EXCH: HLD350/2000 MK2 HYDR.CYLIND. ASS'Y HLD2000 MK2L HYDR.CYLINDER ASS'Y EXCH: HLD2000 MK2L HYDR.CYLINDER ASS'Y HLD BASE PLATE ASS'Y BALL JOINT DIA 12 x M12 (Substitutes 21113295) HLD2000MK2 PIPE WITH BANJO COUPLING HLD2000MK2L PIPE WITH BANJO COUPLING HLD350/2000 MK2 PISTON ASS'Y HLD2000L MK2 PISTON ASS'Y HLD350/2000 MK2 TANK ASS'Y BYPASS VALVE 12V COMPLETE BYPASS VALVE 24V COMPLETE HLD350 MK2 HYDR. LINEAR DRIVE HLD350 MK2 HYDR. LINEAR DRIVE EXCH. HLD350 MK2 HYDR. LINEAR DRIVE HLD2000 MK2 SEAL KIT, COMPL. RPU80 LEMAC MOTOR 12V (SUBSTITUTES RPU80 FRACMO MOTOR 12V) BRUSH LEMAC C8386 9x6x18,2MM (PAIR) BRUSH FRACMO CBC 188, 7,2x6,5x10MM (PAIR) HLD350S FLEXIBLE HOSES ASS'Y HLD350 MK2 PUMP AND MOTOR ASS'Y HLD350/2000 MK2 HYDR.CYLIND. ASS'Y HLD350/2000 MK2 TANK ASS'Y MLD200 MECHANICAL LINEAR DRIVE MLD200 W/BUILT IN RUDDER FB EXCH: MLD200 MECHANICAL LINEAR LFI3000 INTERFACE PCB ASS'Y HLD EMERG.RELEASE PIN ASS'Y LF3000 COIL CORE MLD200 TOOTH BELT MLD200 MOTOR 10V/35W MLD200 CLUTCH (12V) BALL JOINT DIA 12 x M12 (Substitutes 21113295) BRUSH LEMAC C8386 9x6x18,2MM (PAIR) DD15 DIRECT DRIVE DD15 DIRECT DRIVE EXCH. DD15 DIRECT DRIVE DRAGLINK DL2030 DRAGLINK DL3040 DRAGLINK DL4050 REFERENCE

for 8 ch.system

** for 8 ch.system ** for 8 ch.system
** ** ** for 8 ch.system ** for 8 ch.system ** for 8 ch.system **

26056036

** for 8 ch.system ** for 8 ch.system for 8 ch.system ** ** ** for 8 ch.system ** for 8 ch.system
Navico Egersund PART NO. DESCRIPTION NOTES! Exchange sensitive element is completely refurbished and includes 12 month warranty. All orders for exchange sensitive elements, warranty or non-warranty, for any Simrad model gyrocompass will be invoiced in full when the element is shipped. Exchange credit or approved warranty will be evaluated when broken element, including all belonging parts, is received at Navico Egersund. Sensitive elements may be sent to Navico Egersund AS for overhaul. Turn-around time is normally one month. Price NOK 10 500,- NET. REFERENCE

RGC10 GYRO COMPASS

44138493 44134880
MASTER COMPASS PARTS RGC10 SENSITIVE ELEMENT EXCH: RGC10 SENSITIVE ELEMENT RGC10 CASE ASS'Y RGC10 ELEMENT CARTON BOX

102390410 102394390

44141620 44175305
GYRO ASS'Y PARTS RGC10 LEVEL ASS'Y RGC10/11 SUSPENSION WIRE ASS'Y RGC10 FLW-UP COIL ASS'Y SEC. RGC10 PRIMARY FOLLOW-UP COIL RGC10 LIQUID BALLIST. ASS'Y RGC10/11 SERVO MOTOR ASS'Y W/O MOTOR RGC10/11 SPUR GEAR RGC10/11 TERMINAL BOARD ELECTRONIC BOARDS RGC10 TRANSM. PCB ASS'Y VER.0 EXCH: RGC10 TRANSM. PCB ASS'Y VER.0 RGC10/11 T/M PCB ASS'Y VER.1 EXCH: RGC10/11 T/M PCB ASS'Y VER.1 RGC10 SERVO AMP PCB ASS'Y EXCH: RGC10 SERVO AMP PCB ASS'Y RGC10 PANEL PCB ASS'Y EXCH: RGC10 PANEL PCB ASS'Y BEARINGS RGC10/11 ROTOR BEARING (CHERAMIC) RGC50/10/11 BEARING V.AXIS & HORIS. RING RGC10 LOWER VERTICAL BEARING ASS'Y

102300423

44138584 44138584

102395280 102395280

44138618

102393070

Spare Parts Price List 2007 PART NO. DESCRIPTION RGC10/11 BEARING HOR.RING N/S RGC10 HARNESS PH.RING RGC10/11 PHANTOM RING BEARING SERVO MOTOR ELECTRICAL RGC10 BRUSH ASS'Y 1 (3 BRUSHES) RGC10 BRUSH ASS'Y 2 (2 BRUSHES) RGC10 SLIP RING INVERTER GC80/85/RGC10/11/12 INVERTER ASS'Y EXCH: GC80/85/RGC10/11/12 INVERTER ASS'Y EXCH: RGC10 INVERTER ASS'Y "BLUE MARK" RGC10 INV. OCT. PCB EXCH: RGC10 INV. OCT. PCB COIL L22 1mH/1A COIL L1 SC-05-100 MISCELLANEOUS RGC10/11 LUBBER LINE (HEAD MARK) RGC10/11 LAMP, COMPASS CARD RGC10 SHOCK ABSORBER ASS'Y RGC10/11 COMPASS CARD MOTORS RGC10 SYNC. TRANSMITTER ASS'Y RGC10 SYNC.TRANSM. 15 Cx4 RGC10/11 SERVO MOTOR SYNCHRO TRANSFORMER ASS'Y COVER RGC10 GLASS RGC10 PANEL ASS'Y RGC10/11 KNOB/SCREW (2 PCS.) RGC10/11 LIQUID BALLISTIC O-RING (4 PCS.) OIL BEARING OIL, VERT/HORIZ 10 ml LIQUID BALLISTIC OIL (20ML) DAMPER OIL TUBE (15 CCM/TUBE) GREASE FOR UPPER VERTICAL BEARING GREASE FOR ROTOR BEARING 30 GR GYRO SLIPRING LUBRICATION OIL, 20ml REFERENCE

44142073

102394250

44141687

102395850 102395850

44138261 44140853

102393180

44138287 20201125

103501510

27103621 27103613

102300930 102390680

44138451 27102128

DTE (20 ml) #ANDOC 260
Navico Egersund PART NO. DESCRIPTION TRANSMISSION UNIT RGC10/11 STEP AMP PCB ASS'Y VER1 EXCH: RGC10/11 STEP AMP PCB ASS'Y VER1 WIRES RGC10 HARNESS HOR.RING E/N RGC10 HARNESS HOR.RING W/N RGC10 HARN.PU COIL-HOR.RING RGC10 HARNESS VERT-HOR RING RGC10/11 LAMP, COMPASS CARD RGC10/11 OIL DAMPER CASE RGC10/11 DAMPER CASE COVER AXIS RGC10/11 AXIS, VERTICAL RGC50/10/11 SERVICE KIT (Adjust weights, grease and tools) NOTES! Exchange sensitive element is completely refurbished and includes 12 month warranty. All orders for exchange sensitive elements, warranty or non-warranty, for any Simrad model gyrocompass will be invoiced in full when the element is shipped. Exchange credit or approved warranty will be evaluated when broken element, including all belonging parts, is received at Navico Egersund. Sensitive elements may be sent to Navico Egersund AS for overhaul. Turn-around time is normally one month. Price NOK 10 500,- NET. REFERENCE 10239504 10239504

44141364

10230039

44177038 13108196

10210210

RGC11 GYRO COMPASS

27104215 44134880
MASTER COMPASS PARTS RGC11 SENSITIVE ELEMENT W/CPU I/F PCB EXCH: RGC11 SENSITIVE ELEMENT W/CPU I/F PCB RGC11 EPROM (STATE THE S/N WHEN ORDERING) RGC11 ELEMENT CARTON BOX 102394390

44141612 26

GYRO ASS'Y PARTS RGC10/11 COMPASS CARD RGC10/11 LAMP, COMPASS CARD RGC10/11 NOISE FILTER

200305840

Spare Parts Price List 2007 PART NO. 44175305 DESCRIPTION RGC10/11 SERVO MOTOR ASS'Y W/O MOTOR RGC10/11 SPUR GEAR RGC11 PRIMARY PICK-UP COIL RGC11 SECONDARY PICK-UP COIL RGC10/11 TERMINAL BOARD ELECTRICAL GC80/85/RGC11/12 BRUSH ASS'Y RGC11 HARNESS E-N RGC11 HARNESS W-N GC80/85/RGC11/12 SLIP RING ELECTRONIC BOARDS RGC11 PANEL ASS'Y, CONTROL PCB EXCH: RGC11 PANEL ASS'Y, CONTROL PCB RGC10/11 T/M PCB ASS'Y VER.1 EXCH: RGC10/11 T/M PCB ASS'Y VER.1 RGC11 SERVO AMPLIFIER PCB ASS'Y EXCH: RGC11 SERVO AMPLIFIER PCB ASS'Y RGC11 CPU I/F PCB ASS'Y EXCH: RGC11 CPU I/F PCB ASS'Y RGC11 CPU PCB ASS'Y EXCH: RGC11 CPU PCB ASS'Y RGC11 CPU P.S. PCB ASS'Y EXCH: RGC11 CPU P.S. PCB ASS'Y BEARINGS RGC10/11 ROTOR BEARING (CHERAMIC) RGC50/10/11 BEARING V.AXIS & HORIS. RING RGC10/11 BEARING HOR.RING N/S INVERTER GC80/85/RGC10/11/12 INVERTER ASS'Y EXCH: GC80/85/RGC10/11/12 INVERTER ASS'Y EXCH: RGC11 INVERTER ASS'Y "BLUE MARK" NOTE: WE OFFER THE OLD VERSION (44166437) AS LONG AS AVAILABLE FROM STOCK. REFURBISHED WITH EXTRA 10% DISCOUNT. RGC11 INV. OCT. PCB EXCH: RGC11 INV. OCT. PCB MISCELLANEOUS RGC10/11 LUBBER LINE (HEAD MARK) RGC10/11 LAMP, COMPASS CARD RGC10 SHOCK ABSORBER ASS'Y REFERENCE

102393422 102393453

44141356 44142081

10239379

101692600

44141034 44141034

10239531 10239531

44141109

102102361 102103260

44166437

102391727 102391727

44138261

Navico Egersund PART NO. 27103621 DESCRIPTION RGC10/11 COMPASS CARD RGC11 GLASS RGC11 COVER RGC10/11 LIQUID BALLISTIC O-RING (4 PCS.) RGC10/11 KNOB/SCREW (2 PCS.) TRANSMISSION UNIT RGC10/11 STEP AMP PCB ASS'Y VER1 EXCH: RGC10/11 STEP AMP PCB ASS'Y VER1 RGC10/11 OIL DAMPER CASE RGC10/11 DAMPER CASE COVER OIL BEARING OIL, VERT/HORIZ 10 ml LIQUID BALLISTIC OIL (20ML) DAMPER OIL TUBE (15 CCM/TUBE) GREASE FOR UPPER VERTICAL BEARING GREASE FOR ROTOR BEARING 30 GR GYRO SLIPRING LUBRICATION OIL, 20ml RGC50/10/11 SERVICE KIT (Adjust weights, grease and tools) RGC50/10/11/12 ADJUSTING WEIGHTS ADJUSTING WEIGHTS 25x1,5 mm, kit 10pcs. ADJUSTING WEIGHTS 10x0,3 mm, kit 10pcs. ADJUSTING WEIGHTS 10x0,5 mm, kit 10pcs. ADJUSTING WEIGHTS 10x1,0 mm, kit 10pcs. ADJUSTING WEIGHTS 10x1,5 mm, kit 10pcs. ADJUSTING WEIGHTS 19x0,5 mm, kit 10pcs. ADJUSTING WEIGHTS 19x1,0 mm, kit 10pcs. ADJUSTING WEIGHTS 19x1,5 mm, kit 10pcs. NOTES! Exchange sensitive element is completely refurbished and includes 12 month warranty. All orders for exchange sensitive elements, warranty or non-warranty, for any Simrad model gyrocompass will be invoiced in full when the element is shipped. Exchange credit or approved warranty will be evaluated when broken element, including all belonging parts, is received at Navico Egersund. REFERENCE

44141323 44141364

10230038 10230039

13108196

44166304 44166296
Spare Parts Price List 2007 PART NO. DESCRIPTION Sensitive elements may be sent to Navico Egersund AS for overhaul. Turn-around time is normally one month. Price NOK 10 500,- NET. REFERENCE

RGC12 GYRO COMPASS

44140861 27102128
MASTER COMPASS GC80/RGC12 SENSITIVE ELEMENT EXCH: GC80/RGC12 SENSITIVE ELEMENT GC80/RGC12 RUBBER TUBE RGC80/85/RGC12 HRZC PCB ASS'Y EXCH: RGC80/85/RGC12 HRZC PCB ASS'Y RGC12 MCU PCB ASS'Y EXCH: RGC12 MCU PCB ASS'Y RGC12 PMCU PCB ASS'Y EXCH: RGC12 PMCU PCB ASS'Y RGC12 STDM PCB ASS'Y EXCH: RGC12 STMD PCB ASS'Y RGC12 POWER TRANSFORMER GC80/85/RGC10/11/12 INVERTER ASS'Y EXCH: GC80/85/RGC10/11/12 INVERTER ASS'Y RGC12 STEP MOTOR ASS'Y W/ STEP MOTOR GC80/85/RGC12 BELT RGC12 STEP MOTOR RGC12 GLASS RGC12 LINE FILTER RGC12 BEARING, HORIZONTAL RING GC80/85/RGC12 ELEMENT CARTON BOX GC80/85/RGC12 HARNESS ASS'Y N-E GC80/85/RGC11/12 BRUSH ASS'Y GYRO SLIPRING LUBRICATION OIL, 20ml CONTROL BOX RGC12 SCU PCB ASS'Y EXCH: RGC12 SCU PCB ASS'Y RGC12 POWER SUPPLY PCB ASS'Y EXCH: RGC12 POWER SUPPLY PCB ASS'Y RGC12 OPT PCB ASS'Y EXCH: RGC12 OPT PCB ASS'Y RGC12 ADD PCB ASS'Y EXCH: RGC12 ADD PCB ASS'Y RGC12 OPS PCB ASS'Y EXCH: RGC12 OPS PCB ASS'Y RGC12 NSD PCB ASS'Y EXCH: RGC12 NSD PCB ASS'Y RGC12 EXTENSION CABLE, 10M GC80/85/RGC11/12 SLIP RING

101697065 10239379

44169639 44142081

10169564 10169564

Navico Egersund PART NO. DESCRIPTION TOOLS GC80/85/RGC12 MOUNTING JIGS 3,2 mm & 3,4 mm GC80/85/RGC12 REFERENCE LEVEL TOOL RGC50/10/11/12 ADJUSTING WEIGHTS ADJUSTING WEIGHTS 25x1,5 mm, kit 10pcs. ADJUSTING WEIGHTS 10x0,3 mm, kit 10pcs. ADJUSTING WEIGHTS 10x0,5 mm, kit 10pcs. ADJUSTING WEIGHTS 10x1,0 mm, kit 10pcs. ADJUSTING WEIGHTS 10x1,5 mm, kit 10pcs. ADJUSTING WEIGHTS 19x0,5 mm, kit 10pcs. ADJUSTING WEIGHTS 19x1,0 mm, kit 10pcs. ADJUSTING WEIGHTS 19x1,5 mm, kit 10pcs. NOTES! Exchange sensitive element is completely refurbished and includes 12 month warranty. All orders for exchange sensitive elements, warranty or non-warranty, for any Simrad model gyrocompass will be invoiced in full when the element is shipped. Exchange credit or approved warranty will be evaluated when broken element, including all belonging parts, is received at Navico Egersund. REFERENCE

44174449 44174431

GC80/GC85 GYRO COMPASS (MASTER COMPASS)
GC85 SENSITIVE ELEMENT EXCH: GC85 SENSITIVE ELEMENT GC80/RGC12 SENSITIVE ELEMENT EXCH: GC80/RGC12 SENSITIVE ELEMENT GC80/RGC12 RUBBER TUBE GC80/85 MCC PCB ASS'Y GC80/85/RGC12 HRZC PCB ASS'Y EXCH: RGC80/85/RGC12 HRZC PCB ASS'Y GC80/85 SMCC PCB ASS'Y GC80/85 MTTRM PCB ASS'Y GC80/85/RGC12 BELT GC80/85 STEP MOTOR ASS'Y GC80/85/RGC12 HARNESS ASS'Y N-E GC80/85/RGC11/12 BRUSH ASS'Y GC80/85/RGC11/12 SLIP RING GC80/85/RGC10/11/12 INVERTER ASS'Y EXCH: GC80/85/RGC10/11/12 INVERTER ASS'Y GC80/85/RGC12 MOUNTING JIGS 3,2 mm & 3,4

102391727

Spare Parts Price List 2007 PART NO. 27102128 DESCRIPTION mm GC80/85/RGC12 REFERENCE LEVEL TOOL GC80/85/RGC12 ELEMENT CARTON BOX GYRO SLIPRING LUBRICATION OIL, 20ml GC80/85 COMPACT CONTROL UNIT GC80/85 ICIF PCB ASS'Y GC80/85 GPANEL PCB ASS'Y GC80/85 IOPT PCB ASS'Y GC80/85 ITERM PCB ASS'Y GC80/85 SWITCH ASS'Y GC80/85 SWITCH COVER POWER SUPPLY UNIT GC80/85 GPOWER PCB ASS'Y GC80/85 EXPANDED CONTROL UNIT GC80/85 SCC PCB ASS'Y GC80/85 SCOIF PCB ASS'Y (EXPANDED) GC80/85 GPANEL PCB ASS'Y GC80/85 GTERM PCB ASS'Y GC80/85 GPOWER PCB ASS'Y GC80/85 SWITCH ASS'Y GC80/85 SWITCH COVER GC80/85 DUAL CONTROL UNIT GC80/85 SCC PCB ASS'Y GC80/85 SCOIF PCB ASS'Y (DUAL) GC80/85 GPANEL PCB ASS'Y GC80/85 DTERM PCB ASS'Y GC80/85 GTERM PCB ASS'Y GC80/85 DRY PCB ASS'Y GC80/85 DPANEL PCB ASS'Y GC80/85 PCC PCB ASS'Y GC80/85 SWITCH COVER GC80/85 GPOWER PCB ASS'Y NOTES! Exchange sensitive element is completely refurbished and includes 12 month warranty. All orders for exchange sensitive elements, warranty or non-warranty, for any Simrad model gyrocompass will be invoiced in full when the element is shipped. Exchange credit or approved warranty will be evaluated when broken element, REFERENCE 101692201

44142396 44142404

10189207 AT-4171

44142412

10189517

44142404

AT-4171

44142404 44142412

44142396 AT-4171 10189517
Navico Egersund PART NO. DESCRIPTION including all belonging parts, is received at Navico Egersund. RGC SIGNAL INTERFACE UNIT SUBSTITUTED BY GI51 GYRO INTERFACE GI51 GYRO INTERFACE EXCH: GI51 GYRO INTERFACE (REPLACEMENT FOR RGC SIGNAL INTERF. UNIT) EXCH: GI51 GYRO INTERFACE (REPLACEMENT FOR EXCH: RGC SIGNAL INTERF. PCB ASS'Y) REFERENCE PRICE

20213773

GYRO REPEATERS

27103365

EXCH: DR75 REPEATER, REPLACED BY: EXCH: DR76 DIGITAL REPEATER

27103340

EXCH: AR77 ANALOG REPEATER, REPLACED BY: EXCH: AR78 ANALOG REPEATER EXCH: AR68 ANALOG REPEATER, REPLACED BY: EXCH: AR80 ANALOG REPEATER RGC BEARING REPEATER RGC BEARING REPEATER LAMP (2 PCS.) AR78 ANALOG REPEATER EXCH: AR78 ANALOG REPEATER AR80 ANALOG REPEATER EXCH: AR80 ANALOG REPEATER DR76 DIGITAL REPEATER EXCH: DR76 DIGITAL REPEATER

27103324

27103639
Spare Parts Price List 2007 PART NO. 27102128 DESCRIPTION mm GC80/85/RGC12 REFERENCE LEVEL TOOL GC80/85/RGC12 ELEMENT CARTON BOX GYRO SLIPRING LUBRICATION OIL, 20ml GC80/85 COMPACT CONTROL UNIT GC80/85 ICIF PCB ASS'Y GC80/85 GPANEL PCB ASS'Y GC80/85 IOPT PCB ASS'Y GC80/85 ITERM PCB ASS'Y GC80/85 SWITCH ASS'Y GC80/85 SWITCH COVER POWER SUPPLY UNIT GC80/85 GPOWER PCB ASS'Y GC80/85 EXPANDED CONTROL UNIT GC80/85 SCC PCB ASS'Y GC80/85 SCOIF PCB ASS'Y (EXPANDED) GC80/85 GPANEL PCB ASS'Y GC80/85 GTERM PCB ASS'Y GC80/85 GPOWER PCB ASS'Y GC80/85 SWITCH ASS'Y GC80/85 SWITCH COVER GC80/85 DUAL CONTROL UNIT GC80/85 SCC PCB ASS'Y GC80/85 SCOIF PCB ASS'Y (DUAL) GC80/85 GPANEL PCB ASS'Y GC80/85 DTERM PCB ASS'Y GC80/85 GTERM PCB ASS'Y GC80/85 DRY PCB ASS'Y GC80/85 DPANEL PCB ASS'Y GC80/85 PCC PCB ASS'Y GC80/85 SWITCH ASS'Y GC80/85 SWITCH COVER GC80/85 GPOWER PCB ASS'Y NOTES! Exchange sensitive element is completely refurbished and includes 12 month warranty. All orders for exchange sensitive elements, warranty or non-warranty, for any Simrad model gyrocompass will be invoiced in full when the element is shipped. Exchange credit or approved warranty will be evaluated when broken element, REFERENCE 101692201
10189207 AT-4171 10189517
Navico Egersund PART NO. DESCRIPTION CS56 CHART SYSTEM w/MC50 CS SPEAKER USB LS60-M LOUDSPEAKER FB200 MC 24V FILTERBOX MC50 FOUR CHANNEL DC EXCH: MC50 FOUR CHANNEL DC MC50 EIGHT CHANNEL DC EXCH: MC50 EIGHT CHANNEL DC CS55/56 SOFTWARE CD CHART INTERFACE UNIT EXCH: CHART INTERFACE UNIT MC50 FOUR CHANNEL AC EXCH: MC50 FOUR CHANNEL AC MC50 FOUR CHANNEL RAID AC EXCH:MC50 FOUR CHANNEL RAID AC MC50 FOUR CHANNEL RAID DC EXCH:MC50 FOUR CHANNEL RAID DC MC50 EIGHT CHANNEL AC EXCH:MC50 EIGHT CHANNEL AC MC50 EIGHT CHANNEL RAID DC EXCH:MC50 EIGHT CHANNEL RAID DC MC50 EIGHT CHANNEL RAID AC EXCH:MC50 EIGHT CHANNEL RAID AC ** By exchange of MC50 Computer, Software must be ordered separately CS66 CHART SYSTEM w/MC50 CS SPEAKER USB LS60-M LOUDSPEAKER FB200 MC 24V FILTERBOX MC50 FOUR CHANNEL DC EXCH: MC50 FOUR CHANNEL DC MC50 EIGHT CHANNEL DC EXCH: MC50 EIGHT CHANNEL DC CS66 SOFTWARE CD CHART INTERFACE UNIT EXCH: CHART INTERFACE UNIT MC50 FOUR CHANNEL AC EXCH: MC50 FOUR CHANNEL AC MC50 FOUR CHANNEL RAID AC EXCH:MC50 FOUR CHANNEL RAID AC MC50 FOUR CHANNEL RAID DC EXCH:MC50 FOUR CHANNEL RAID DC MC50 EIGHT CHANNEL AC EXCH:MC50 EIGHT CHANNEL AC MC50 EIGHT CHANNEL RAID DC REFERENCE