notice dry contact

10/03/03

Page 1

INSTALLATIONguide

DRY CONTACT TRANSMITTER

The DRY CONTACT TRANSMITTER is a RTS control that can be controlled driven by a key switch, a paddle switch, a Centralis IB or a dry contacts rain sensor. The UP or DOWN radio commands are achieved when the UP or DOWN inputs ( ) are connected with the common input (C). The STOP command is achieved when the three inputs ( C) are conected together.

Programing button LED

Ref.5006405A

Characteristics

PROG ,S,,S
Built-in manual security control
Supply : 220-240V 2,5A 50/60Hz Fuse : 3,15A Transmission timing : min0,5 sec. max10 sec. Frequency : 433.42 MHz Protection index : IP30 Temperature : +5C to +40C Class II product
Hereby, SOMFY, declares that this equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. A Declaration of Conformity is available at the web address www.somfy.com Heading CE

usable in EU, CH

Installation
This device must be installed and programmed by qualified installers for whom this instruction is intended. Before connecting the unit, read the instructions carefully.
MAINS 230V - 50Hz Neutral Phase
Cabling of a CENTRALIS IB

2 x 1,5 mm2

Set the switch on the "-" position

Brown Blue

L = Mains phase N = Mains neutral C = common

= UP = DOWN

SUPPLY 230V 50Hz

Phase Neutral Earth

CENTRALIS IB

Dry contacts TRANSMITTER

Cabling of a Key switch

MAINS 230V - 50Hz

Neutral Phase

KEY SWITCH

L = Mains phase N = Mains neutral C = common = UP = DOWN
We reserve the right to make changes due to technical improvements.

Page 2

Cabling of a rain sensor
2 x 1,5 mm2 MAINS 230V - 50Hz Earth Neutral Phase

Rain sensor

yellow/green brown blue blue brown brown blue yellow/green blue brown

RAIN SENSOR

Mounting

RECESSED mounting

Screw the support on the recessed box.
Complete the cabling and clip the receiver on the support.

Clip the front cover.

SURFACE mounting
Screw the flush mounting box onto the wall.
Screw the support on the box.

Clip the front cover

Programming
Programing button LED PROG ,S,,S
INITIAL INSTALLATION To record the first DRY CONTACT TRANSMITTER
Set the RTS receiver in its programming mode (refer to the relevant instruction guide). Press the programming button on the frontside of the DRY CONTACT TRANSMITTER RTS until the reaction of the RTS receiver (blinking of a light or movement of the end-product). The address of the transmitter is memorized by the RTS receiver which automatically quits its programming mode.
EXISTING INSTALLATION To add a new DRY CONTACT TRANSMITTER
Press more than two seconds on the programming button of a RTS transmitter already memorized in the RTS receiver in order to wake up the receiver. Record the new control by pressing the programming button on the frontside of the transmitter until the reaction of the RTS receiver (blinking of a light or movement of the end-product). The address of the transmitter is memorized by the RTS receiver which automatically quits its programming mode.
C DELETE A DRY CONTACT TRANSMITTER
Carry out the same procedure as described in chapter 3A : Set the RTS receiver in its programming mode, then press the prog button of the transmitter you wish to delete.
SOMFY SAS, capital 20.000.000 Euros, RCS Bonneville 303.970.230

RTS DRY-CONTACT INTERFACE

Operating Instructions

The RTS dry-contact Interface (Catalog 6300454) can be used to communicate between home automation or other third party systems and SOMFYs RTS Motors and Inteo line of controls.

Battery Holder

RED BLACK GREEN WHITE

Programming Button

NOTE: Please Consult RTS Motor Instructions for Specific Product Details.
1. Place the RTS Motor in Programming Mode as described in the individual product operating instructions. 2. Press the programming button on the RTS Interface to program it in the memory of the RTS Motor. 3. To activate an UP command, a momentary contact (relay) closure is required between the WHITE and GREEN wires. 4. To activate a DOWN command, a contact closure is required between the BLACK and GREEN wires. 5. To activate a STOP command or Intermediate Position, a contact closure is required between the RED and GREEN wires.

SOMFY CANADA

6315 Shawson Drive, Unit #1 Mississauga, Ontario L5T1J2
SOMFY SYSTEMS, INC. reserves the right to change, update or improve this document without prior notice.

SOMFY SYSTEMS, INC.

47 Commerce Drive Cranbury, NJ 08512
SOMFY MEXICO S.A. De C.V.
Calle 3 No.47, Loc.E-5 Fracc Ind. Alce Blanco Nau.,Edo. de Mex C.P 53370,Mex.
C SOMFY SYSTEMS, INC. 3/02