100 50/60

4 3,6 40x1,5

40x1,5 1.1

0,75 IP44

Standard

CTS 40
CTS 40 Cord Take up System Cord lift and tilt system for all blinds. Even cord winding on cone. Adaptable for headrails of 51 x 57 mm. Capacity: 35 revolutions of 1.4 mm cord = 5.5 m.

Venetian Blinds

LS 40: 20 Kg Maxi. Height: 5.5 m
Product Cord Take-up System. Cord lift and tilt system for blinds. Driven by octogonal tube. Even cord winding on cone. Application Venetian, Roman, Austrian blinds. Maximum travel 5500 mm of 1.4 mm cord with core. For other cords, contact us. Adaptation to headrail By specifically to headrail designed cradle. Adaptation to tube By specifically to tube designed cone.

Roman Blinds

MOTORIZED BLIND Mounting In headrail. No preferential direction of rotation. Operation By motor (or manual systems).
TECHNICAL D ATA TEC HNICAL Cord diameter Cord type Cord material Cord braiding Cord with Core Cord treatment Maximum load per 1.4 mm cord Maximum length of 1.4 mm cord which can be rolled - nbr of turns Working temperature (C)
C TS 1.4 mm Round Braided 100% Polyester yarns 16 ends Yes Stabilized 4 Kg *5.5 m - 35 turns 0 to +60
*Tested only on blinds up to 4 m
CTS 40 IS A PATENTED SYSTEM Patent Numbers EP554212, US5328113 JP 5 - 13758

200.15 380.05 40.50.3

41.80.2

26.10.2

31.10.3 104.6 maxi

LT 50 RH

LT 50 RH.
Maxi. load: 70 Kg Maxi. Height: 7 m
Product Tubular operator with built in brake, adjustable up and down limit switches. Adaptable to round tube ID mini 50 x 1,15 mm by identical to tube designed crown and drive adapters. Application Roller blinds and roman shades with CTS 50. Maximum travel 46 revolutions of roller tube.
Maxi. load: 70 Kg Maxi. Height: 5.5 m
MOTORIZED BLIND Mounting By 2 self tapping screws fixed motor brackets or directly on blind side plates. Cable: Axial and/or radial motor output: See General catalogue for length. Control range Compatibility with Somfy AC controls. Wood Venetian Blinds

E AN ARI S ME HER INI GEM

S2 504

A5 A5225

S2 506

R3 525

S3 505

F2 505

S2 510

S3 510

AS ATL

S2 515
L1 (in mm) L2 - Drilling length (in mm) L3 (in mm) Torque Nm Speed in Rpm. Limit switch capacity Electrical rating (watts) Voltage (VAC) Frquency (Hz) Amperage (A) Continuous running time Operator outside (mm) Minimum of roller tube (mm) Operator weight (Kg) Cable Length (m) Conductors Gauge (mm2)

50 0,45 4

50 0,5 4

50 0,65 4

50 0,8 4

60 0,7 5

60 1,3 5

60 1,8 5

32/50/60 1,05 5

32/50/60 1,55 5

12/50/60 0,7 5

50 0,75 5

120 60

50x1,15 1,72

50x1,15 1,85

50x1,15 1,95

50x1,15 2,2

50x1,15 1,82

50x1,15 2

50x1,15 2,55

50x1,15 1,75

4 0,75 IP44

4 AWG18 IP44

4 AWG18 IP44

4 0,75 IP44
Standard L1 Lmax Basic crown for tube 50 x 1,15
16,85 mini 11,06 max 4,95 max

25,1 mini

2,050.25 13,2 mini

L 3 max

49,6 maxi 2 holes forself-cutting screw 4 with entre-axe 29 mm0.5
Holes 12 mini & depth 19,5 mini.

15,7 mini buttons

34,5 max buttons

CTS 50

CTS 50 Cord Take up System Cord lift and tilt system for all blinds. Even cord winding on cone. Adaptable for headrail Nichibe (70 X 70) and tube Nichibe Capacity: 35 revolutions of 1.4 mm cord = 5.5 m.
LT 50: 10 Nm max. Maxi Height: 6.40 mm Cord diameter: 1.3 mm
Product Cord Take-up System. Cord lift and tilt system for blinds. Driven by octogonal tube. Even cord winding on cone. Application Venetian, Roman, Austrian, Pleated blinds. Maximum travel 6000 mm of 1.3 mm cord with core. For other cords, contact us. Adaptation to headrail By specifically to headrail designed cradle. Adaptation to tube By specifically to tube designed cone.
Max dimension: 6.4 m X 6.4 m
MOTORIZED BLIND Mounting In headrail. No preferential direction rotation. Operation By motor (or manual systems).
Pleated Blinds With CTS 50
C TS 50 1.3 mm Round Braided 100% Polyester yarns 16 ends Yes Stabilized 5 Kg 6 m - 35 turns 0 to +50
CTS 50 IS A PATENTED SYSTEM Patent Numbers EP554212, US5328113 JP 5 - 0.15

54.7 0.2

10 0.2

44 0.2

44 0.05 31.1 0.3 24

83.5 maxi

PART 2

1 DIMENSION CHART

page 16

SOLUTIONS

2 MOTOR SELECTION CHART Venetian blind Roller blind Roman & Balloon blinds 3 ASSEMBLY INSTRUCTIONS LS 40 CTS 40 LT 50 RH 4 RECOMMENDATIONS page 35 page 41 page 47 page 52 page 17 page 23 page 31

2.1 DIMENSION CHART

Crown #9500341 Wheel #9500340 $ Estimated maximum values, depending on type of fabric s, slats, bottom bar, hardware system.Consult Somfy for precise calculation 29
< Roman & Balloon blinds >
2.3 ASSEMBLY INSTRUCTIONS

< LS 40 >

a.PREPARING THE TUBE. - Cut the roller tube to the required length. Note: Take into account the installation width, the width of the motor head, the type of plug end and the bracket size. - De-burr the ends of the tube and ensure that the inside of the tube is clean. - Fit the plug end into the other end of the tube and secure with four steel pop rivets.
b.PREPARING THE TUBULAR MOTOR. - Place the crown wheel over the body of the motor and slide it over the raised key of the motors limit switch unit. - Place the drive wheel onto the output shaft of the motor.
c.FITTING THE MOTOR INTO THE TUBE. - Measure the drilling length as shown on the right. Do not drill into the motor output shaft. - Fit the motor into the tube, ensuring that the slot at the end of the tube slides over the key on the crown wheel. - Secure the drive wheel to the tube using 4 x 5mm steel pop rivets, placed at 120 from each other.

Attaching zone

Drilling length to measure
d.MOTOR END FITTING. - Three possible ways of fixing the motor head:
With 2 screws directly on the head
With a square shaft 10 mm rf. 9147334
With a flat <LO> bracket ref. 9147337
e.INSTALLING THE MOTORISED TUBE Note: Install the motor bracket on the same side as the power supply. - Fit the brackets, but do not tighten them. - Fit the plug end bracket over the plug end. - Ensure that the tube is horizontal using a spirit leveller. - Tighten the brackets once it is level. f. WIRING RECOMMENDATIONS The Electrical Supply Regulations 1988 give an Electricity Board the right to refuse to supply, or continue the supply to, a consumers installation which is not safe or which may cause interference with the supply to others. The Electricity Supply Regulations accept Regulations comply with all safety requirements. All electrical installations are governed by the IEE wiring regulations (16th edition).

Goupille ou vis

Square shaft ref. 500602 Motor bracket Plug end bracket

$ except US

Do not wire two or more motors to one switch without using a relay.
Do not use light switches. Do not wire two or more switches to one motor, without using relays approved by SOMFY. g.LIMIT SWITCH SETTING.

Rotate each cone and align for tube insertion
Detail for tube insertion:
Two studs to spot the cone groove Cone

External groove of tube

m.Turn the tube one half a turn to get the cord knot at the bottom of the headrail. Insert the motor into the headrail and the tube. Insert the plug end. The plug end side gets opposite the holes drilled for access to the limit switches.

Motor Plug end

Plug end bracket
n.Insert the plug end bracket into the headrail and onto the plug end.
o.Tie a knot at the bottom end of the cord where the marks have been done.
p.Adjust the top limit and then readjust the bottom limit if necessary. Check and if necessary adjust the horizontality of the bottom bar. CAUTION: do not stack the slats completely, leave at least 25 mm, in up position.
Limit switch access holes

Motor bracket holes

p.Caution transportation packaging. Stacks of slats in the upper position with tight lifting cords.

< LT 50 RH >

a. PREPARING THE TUBE - Cut the tube to the required length, taking into account the width of the installation, the width of the head of the motor, the type of plug end and the size of the plug end bracket. - Deburr the ends of the tube & ensure that the inside of the tube is clean. - For all tube sizes up to & including 85mm diameter, cut a slot in the motor end of the tube to the dimensions shown. - For all tube sizes over 85mm you must form a tongue in the motor end of the tube by making two cuts 25mm apart & 20mm deep. - Fit the plug end into the other end of the tube & secure using 4 steel pop rivets.
b. PREPARING THE TUBULAR MOTOR
1. Place the crown wheel over the body of the motor. Slide the
slot in the crown wheel over the raised key on the motors limit switch unit. A crown wheel is not necessary on 63mm round tubes. 2. Fit the drive wheel onto the output shaft of the motor.* *NB: there are two ways of attaching the drive wheel REMOVABLE - Two of the five internal faces of the drive wheel have grooves. Position these two grooves over the clips of the output shaft. Slide the wheel over the clips until they lock on the lip of the drive wheel. The drive wheel can be removed by physically pulling it off.` FIXED - Position two of the internal faces without grooves over the clips on the output shaft. Slide the drive wheel over the clips until they lock on the lip of the drive wheel. The drive wheel can only be removed by unhooking the two clips from the lip & then removing it.

c. FITTING THE MOTOR INTO THE TUBE For round tubes: - Measure the drilling length. - Fit the motor into the tube ensuring that the slot in the end of the tube slides over the key on the crown wheel. For tube sizes over 85mm diameter tap the tongue in the end of the tube into the recess in the outside diameter of the crown wheel. Secure the drive wheel to the tube using 4 x 5mm steel pop rivets or 4 x M6 countersunk screws.
d. SUPPLY CABLE OUTPUT AXIAL OUTPUT Route the supply cable through the centre hole of the motor bracket. RADIAL OUTPUT Route the supply cable through the groove in the motor head. MOUNTING A MOTORISED TUBE WITH A STANDARD PLUG END Slide the motor head into the motor end bracket and secure with the spring clip. Fit the plug end bracket over the plug end. Ensure the tube is horizontal & tighten the brackets.
e. WIRING RECOMMENDATIONS The Electrical Supply Regulations 1988 give an Electricity Board the right to refuse to supply, or continue the supply to, a consumers installation which is not safe or which may cause interference with the supply to others. The Electricity Supply Regulations accept Regulations comply with all safety requirements. All electrical installations are governed by the IEE wiring regulations (16th edition).
Do not use light switches. Do not wire two or more switches to one motor, without using relays approved by SOMFY.
f. LIMIT SWITCH SETTING SOMFY recommend using a test cable to set the motor limits, and to ensure the system is operating correctly before the final electrical connection is made. Two positions have to be set: the UP & DOWN positions, this is where the rolling shutter or awning will stop automatically. Sequence: 1. Ensure the switch is in the OFF position

2. up position

Remove the protective cap from head of motor
3. Depress fully both limit switch push buttons. They will auto-
matically lock in the down position. Operate the switch and check that the system operates correctly. If not put the switch to the off position, reverse the black & brown motor direction wires and try again.

down position

Identify the UP limit switch push button. Press the switch to the up direction until the required position is reached and put the switch in the off position Unlock the UP limit switch push button by depressing and releasing it Repeat the above operation to set the lower limit

BROWN WIRE

BLACK WIRE
7. Check with the switch that the motor stops at the up & down position just set 8.
Refit the protective cap. NOTE: Tubular motors are not continuously rated. They have a built-in thermal overload device which limits their operation to approximately 4 minutes.

f. TROUBLESHOOTING GUIDE NOTHING WORKS - Is the power supply switched on - check any fuses in the system? - Is control switch wired correctly? Refer to instructions. - Are limit switches set properly? Review limit switch settings. - The thermal protective device may have shut the motor off. Wait for the motor to cool down. - Check the wiring between the motor & the switch. - Disconnect the switch & test the motor with a test cable. THE SYSTEM IS NOT STOPPING - Is the limit switch crown wheel being driven by the tube (has tube profile been properly notched)? -Is motor drive wheel securely fastened to the tube. NB: if the motor is tested outside the tube, the crown wheel has to be manually turned in order to stop the rotation of the output shaft.

2.4 RECOMMENDATIONS

OCTOGONAL TUBES:
TO CHECK THE COMPATIBILITY OF A TUBE WITH CTS40, PLEASE USE THE ATTACHED DRAWINGS. THE DEPRAT TUBE 40 X 0,6 IS COMPATIBLE WITH CTS40, THE DEPRAT 40X 0,8 IS NOT COMPATIBLE.

FOR A GOOD TILTING:

LEAVE THE CORD SLACK IN DOWN LIMIT AND THE LOAD BAR BORNE BY THE LADDERBRAIDS. DO NOT FORGET TO PUT THE LADDERBRAIDS SLAT CLIPS. THE LADDERBRAIDS IS IMPORTANT. TO USE TOO THIN LADDERBRAIDS CAN CAUSE PROBLEMS.

FOR A GOOD LIFTING:

THE DIAMETER AND THE QUALITY OF THE LIFTING CORDS ARE VERY IMPORTANT. OUR TESTS HAVE BEEN CARRIED OUT WITH CORDS FROM JULIUS KOCH AND NIBROL. IN DOWN POSITION THE CORD MUST NOT MAKE ANY DEAD TURNS. TAKE CARE, DURING ASSEMBLY, NOT TO SCRATCH THE CONE FOR INSTANCE WITH A SCREWDRIVER. IN ORDER NOT TO WEAR QUICKLY THE CORDS, THE SLAT PUNCHES MUST BE OF GOOD QUALITY AND OF ADAPTED DIMENSIONS. PRIOR TO ASSEMBLY UNTWIST THE CORDS. TO BE 100% OF THE GOOD HORIZONTABILITY OF THE LOAD BAR AVOID TO MIX CONES FROM DIFFERENT BATCHES ON THE SAME BLIND. WE GUARANTY THE GOOD WORKING OF CTS40 ONLY WHEN THE HEADRAIL IS HORIZONTAL.

ASSEMBLY:

TO LIMIT FRICTION LEAVE A LARGE ENOUGH GAP BETWEEN PLUG END AND BRACKET. TO TAKE INTO ACCOUNT THE CORD DIMENSIONAL CHANGES, DO NOT STACK THE SLATS COMPLETELY. SET THE UP LIMIT AT 25 MM FROM THE HEADRAIL.

TRANSPORTATION:

THE BLINDS MUST BE DISPATCHED RETRACTED. ONCE FITTED, IN ORDER TO SUPPRESS ANY OVERLAPPING OF THE CORD, DRIVE THE BLINDS IN DOWN POSITION. IN ORDER TO CANCEL THE CORD OVERLAPPING, THE STACKS OF SLATS MUST BE CAREFULLY PACKED. (SEE ASSEMBLY INSTRUCTIONS)

ORDERS:

THE CONES AND BEARING CAN ONLY BE ORDERED AND SHIPPED IN BOXES OF 50 PIECES. MINIMUM LENGHT OF HEADRAIL WITH LS 40 + CTS 40: X MM

PART 3

CONTROLS

CHATRT

1 - EUROPEAN CONTROLS

page 54

3.1 EUROPEAN CONTROLS

One motor / one switch

Inis uno inteo 3 positions
One motor / one switch: (Tilt)
Inis uno inteo 5 positions
Group control / one switch (Up to 4 motors)
Group control / one switch (tilt)
Individual and group control with tilt function

Centralis IB

Individual and group control

Centralis uno IB

Centralis IB or Chronis IB

Centralis uno IB VB

Individual and group control with IR

One motor / sun control

Soliris sensor

Soliris uno

Individual and group control with sun function

Soliris IB

Individual and group radio control with SL 7070

Centralis indoor RTS

SL 7070 Drape

Centralis RTS

Telis 1 RTS

Telis 4 RTS

PART 4

REFERENCE LIST

1 - MOTORS 2 - MOTOR ADAPTERS 3 - CONTROLS 4 - CTS
page 60 page 64 page 68 page 71

4.1 MOTORS

- Tubular actuator: 230 V - 50 Hz - Torque 4 Nm speed 14 r.p.m. - Supplied without adapters. - Quantity per standard package: - Weight: 820 g - Tubular actuator: 230 V - 50 Hz - Torque 1.3 Nm speed 55 r.p.m. - Supplied without adapters. - Quantity per standard package: - Weight: 1000 g

MERCURE

- Tubular actuator: 230 V - 50 Hz - Torque 3 Nm speed 30 r.p.m. - Supplied without adapters. - Quantity per standard package: - Weight: 900 g
- Tubular actuator: 230 V - 50 Hz - Torque 9 Nm speed 14 r.p.m. - Supplied without adapters. - Quantity per standard package: - Weight: 1160 g

VULCAN

- Tubular actuator: 230 V - 50 Hz - Torque 13 Nm speed 8 r.p.m. - Supplied without adapters. - Quantity per standard package: - Weight: 1170 g

HERMES RH

- Tubular actuator: 230 V - 50 Hz - Torque 4 Nm speed 32 r.p.m. - Supplied without adapters. - Quantity per standard package: - Weight: 1720 g

ARIANE RH

- Tubular actuator: 230 V - 50 Hz - Torque 6 Nm speed 54 r.p.m. - Supplied without adapters. - Quantity per standard package: - Weight: 1720 g

JET RH

- Tubular actuator: 230 V - 50 Hz - Torque 10 Nm speed 54 r.p.m. - Supplied without adapters. - Quantity per standard package: - Weight: 1850 g

ATLAS RH

- Tubular actuator: 230 V - 50 Hz - Torque 15 Nm speed 32 r.p.m. - Supplied without adapters. - Quantity per standard package: - Weight: 1950 g

GEMINI RH

- Tubular actuator: 230 V - 50 Hz - Torque 25 Nm speed 17 r.p.m. - Supplied without adapters. - Quantity per standard package: - Weight: 2200 g
- Tubular actuator: 120 V - 60 Hz - Torque 1.3 Nm speed 65 r.p.m. - Supplied without adapters. - Quantity per standard package: - Weight: 1000 g

- Tubular actuator: 120 V - 60 Hz - Torque 4 Nm speed 36 r.p.m. - Supplied without adapters. - Quantity per standard package: - Weight: 800 g
- Tubular actuator: 120 V - 60 Hz - Torque 4 Nm speed 16 r.p.m. - Supplied without adapters. - Quantity per standard package: - Weight: 900 g
- Tubular actuator: 120 V - 60 Hz - Torque 9 Nm speed 16 r.p.m. - Supplied without adapters. - Quantity per standard package: - Weight: 1100 g

504 S2 RH

- Tubular actuator: 120 V - 60 Hz - Torque 4 Nm speed 38 r.p.m. - Supplied without adapters. - Quantity per standard package: - Weight: 1720 g

505 F2 RH

- Tubular actuator: 120 V - 60 Hz - Torque 5 Nm speed 64 r.p.m. - Supplied without adapters. - Quantity per standard package: - Weight: 1720 g

506 S2 RH

- Tubular actuator: 120 V - 60 Hz - Torque 6 Nm speed 38 r.p.m. - Supplied without adapters. - Quantity per standard package: - Weight: 1870 g

510 S2 RH

- Tubular actuator: 120 V - 60 Hz - Torque 10 Nm speed 38 r.p.m. - Supplied without adapters. - Quantity per standard package: - Weight: 20000 g

515 S2 RH

- Tubular actuator: 120 V - 60 Hz - Torque 15 Nm speed 38 r.p.m. - Supplied without adapters. - Quantity per standard package: - Weight: 2250 g
- Tubular actuator: 100 V - 50/60 Hz - Torque 3 Nm speed 30 r.p.m. - Supplied without adapters. - Quantity per standard package: - Weight: 900 g
- Tubular actuator: 100 V - 50/60 Hz - Torque 4 Nm speed 14 r.p.m. - Supplied without adapters. - Quantity per standard package: - Weight: 900 g
- Tubular actuator: 100 V - 50/60 Hz - Torque 7 Nm speed 14 r.p.m. - Supplied without adapters. - Quantity per standard package: - Weight: -

505 S3 RH

- Tubular actuator: 100 V - 50/60 Hz - Torque 5 Nm speed 32 r.p.m. - Supplied without adapters. - Quantity per standard package: - Weight: 1750 g

510 S3 RH

- Tubular actuator: 100 V - 50/60 Hz - Torque 10 Nm speed 32 r.p.m. - Supplied without adapters. - Quantity per standard package: - Weight: 2000 g

525 R3 RH

- Tubular actuator: 100 V - 50/60 Hz - Torque 25 Nm speed 12 r.p.m. - Supplied without adapters. - Quantity per standard package: - Weight: 2200 g
- Tubular actuator: 240 V - 50 Hz - Torque 3.5 Nm speed 30 r.p.m. - Supplied without adapters. - Quantity per standard package: - Weight: 1100 g
- Tubular actuator: 240 V - 50 Hz - Torque 9 Nm speed 14 r.p.m. - Supplied without adapters. - Quantity per standard package: - Weight: 1100 g

525 A5 RH

- Tubular actuator: 240 V - 50 Hz - Torque 25 Nm speed 17 r.p.m. - Supplied without adapters. - Quantity per standard package: - Weight: 2200 g

- For direct mounting on side plate

9910011

US LO Plate
- Quantity per standard package: - Weight: 27.6 g

LO Plate 60 mm

9910012

LO Plate

Drive- Wheel for Siral tube and CTS 50 Nichibe Tube 9704080 Wheel
- For tube 52 - No need for crown adaptater - Quantity per standard package: - Weight: 25 g

9410665

Motor bracket for LS 40
- Used with motor bracket 10x10 ref.9147334 - Quantity per standard package: - Weight: 170 g

End plug for LS End Plug

- Quantity per standard package: - Weight: 62 g
Adjustable plug end for LS End Plug
- Pin 12, 40 - Quantity per standard package: - Weight: 200 g
Motor bracket for LS 40 / LT Bracket
- Quantity per standard package: - Weight: 170 g
Interface braket set 9002541 Bracket
- Used with end plug ref.9129630 - Quantity per standard package: - Weight: 344 g
Plug-end bracket diameter 12 (LACQUERED) 9410634 Idler bracket

- Weight: 173 g

Plug-end bracket diameter 12 (ZINCKED) 9410633 Idler bracket
White cover 9002519 Bracket cover
- For bracket Ref: 9410633 - Quantity per standard package: 1 - Weight: 200 g

9500683

- Wall, side and ceiling mounting - Quantity per standard package: 1 - Weight: 45 g - ! up to 4 Nm

9500686

Plug-end bracket
- 9500684: For plug-end 6 - 9500685: For plug-end 8 - 9500686: For plug-end 10 - $up to 4 Nm - Quantity per standard package: 1 - Weight: 45 g - Adaptable to tubes in combination with any LS 40 wheels - $up to 4 Nm - Quantity per standard package: 1 - Weight: 30g

9500688

Universal plug-end 8

9500687

Intermediate bracket set
-Adaptable to tubes in combination with any LS 40 wheel - $up to 4 Nm

4.3 CONTROLS

- 3 positions AC switch - Screw connectors - Contact rating max: - Quantity per standard package: 1 - Weight: 116 g - Dimensions: - 5 positions AC switch - Screw connectors - Contact rating max: - Quantity per standard package: 1 - Weight: 110 g - Dimensions: - Two 3 positions AC switch - Screw connectors - Contact rating max: - Quantity per standard package: 1 - Weight: 135 g - Dimensions: - Two 5 positions AC switch - Screw connectors - Contact rating max: - Quantity per standard package: 1 - Weight: 128 g - Dimensions: - Individual control - Bus line connection for group control

1810016

Inis Uno 3 positions

1800002

Inis Uno 5 positions

1800026

1810307

Telis 4 Patio RTS

- RTS remote control transmitter - 4 channels for individual / group control - 433,42 Mhz frequency - Limited range: 200 m in free field - Quantity per standard package: 1 - weight: 88 g - Dimension: 120 x 45 x 17 - RTS remote control transmitter - 1 channel for individual wind and sun control - 433,42 Mhz frequency - Limited range: 200 m in free field - Quantity per standard package: 1 - weight: 88 g - Dimension: 120 x 45 x 17 - RTS remote control transmitter - 1 channel for individual control - 433,42 Mhz frequency - Limited range: 200 m in free field - Quantity per standard package: 1 - weight: 88 g - Dimension: 120 x 45 x 17

1810308

Telis Soliris Patio RTS

1810025

Telis Soliris US Patio RTS

- Radio receiver

Centralis Indoor RTS
- Radio receiver - For venetians with tilt function

1810110

SL7070 Drape

1870011

IRT 103
- IR transmitter for IRS 100 & 200 - Supplied without batteries - 3 buttons for up, down, stop - Quantity per standard package: 1 - Weight: 45 g - Dimensions: 118 x 45 x 14 - 8 channel infrared transmitter for IRS 300 - Subgroup control 1-4 and 5-8 - Group control 1-8 - Supplied with batteries - Quantity per standard package: 1 - Weight: 101 g - Dimensions: 162x50x20 - Individual control - For bus line and AC motor infrared receiversl

1870010

IRT 803

9154186

IR Sensor
- Quantity per standard package: 1 - Weight: 67 g - Dimensions:

1822033

Bus line Infra-red Receiver AC motor Infra-red Receiver
- Control for Somfy BUS line by infra-red transmitter (IRT 103, IRT 803) or external input (individual push-button or Somfy Bus line). - 220-240 V - Colour: grey - Dimensions: 135 x 120 x 42 - Weight: 330 g - Control for Somfy BUS line by infra-red transmitter (IRT 103; IRT 803) or external input (individual push-button or Somfy Bus line). - 220-240 V - 3 different Drape functions for venetian blinds - Colour: grey - Dimensions: 135 x 120 x 42 - Weight: 330 g - Individual control with tilt function - Bus line connection for group control - 1 per motor - Quantity per standard package: 1 - Weight: 400 g - Dimensions: 112 x 52 x 106 - Group control unit for max. 4 motors

1860000

1810000

CD 4 Drap

1810058
- Quantity per standard package: 1 - Weight: 480 g - Dimensions: 150 x 105 x 75

1870065

White rocker switch S51 AC
- 5 positions white AC rocker switch - Screw connectors - Contact rating max 3 A - 2 momentary positions for pulse tilting - 2 fixed positions for lifting - Quantity per standard package: 1 - Weight: 25 g - Surface mounting box for # 660101/660102/660103

9660135

Switch box
- Quantity per standard package: 1 - Weight: 40 g - Dimensions: 86 x 42 x 39

4.4 CTS

Punching tool for HD 57 x 51 mm
- To adapt the standard HD headrail punch to CTS 40 bearing - Quantity per standard package: 1 - Weight: 7200 g

9090030

Punching tool
Octogonal tube 40 x 1.15 mm Tube
- Extruded tube supplied by Somfy Systems Inc. USA

Cone CTS CTS

- Quantity per standard package: 50 - Weight: 23 g

Bearing CTS CTS

CTS 40 bracket for 51 x 57 headrail 9500736 Bracket
- Quantity per standard package: 1 - Weight: 19 g
CTS 40 bracket for NANIK headrail 9500644 Bracket
- Quantity per standard package: 1 - Weight: 2 g

9137018

End Plug
Plug-end for octogonal tube 40 x 0,6 mm
- Quantity per standard package: 1 - Weight: 37 g
- Quantity per standard package: - Weight: g

Cone 9162240 CTS

Cover 9162242 CTS

Tilting Rod 9162243

PART 5
A D D I T I O N A L I N F O R L M AT I O N
MAXIMUM DIMENSION OF BLINDS

page 74

5.1 LIFTING CAPACITY & MAXIMUM DIMENSIONS OF BLINDS
You will find on page 13 to 16 charts giving the maximum dimensions of blinds you can motorize with the different LS 40 / LT 50 motors. These maximum dimensions are worked out in the following way. Radius 1. The lifting capacity of a motor is given by its torque Torque = Load (Newton) x Radius (metre) 1 Kg 10 N Example: With Mercure which is 4 Nm you can lift in theory on a diameter of 40 mm (radius 20 mm or 0,02 m) 20 kg (4 Nm / 0,02 m = 200N 20 Kg) F LOAD 2. Venetian, Roman and Austrian blinds 2.1 Maximum diameter. 2.1.1 Blinds with lifting cords and equipped with CTS. For these blinds the diameter to consider is the diameter of the cone ( 20 mm ) plus the thickness of the lifting cord: 1.4 mm. Radius = (47 + 1.4)/2 = 24.2 mm. 2.1.2 Blinds with tapes For these blinds the maximum diameter to consider is the diameter of the tape reel when the blind is retracted. This diameter depends on the initial diameter of the take up reel and on the thickness of tape. 2.2 Weight and maximum dimensions. The weight to consider is the weight on the cords or tapes when the blind is retracted, this is the weight of the fabric or slats plus the weight of the bottom bar. 3. Roller blinds In some cases the diameter to consider is the diameter of the rolling tube when the blind is down. The weight to take into account is the weight of the blind when it is down i.e. total weight of fabric and bottom bar. But according to the height of the blinds, the thickness of the fabric and the weight of the bottom bar the maximum torque is not reached at the down position of the blind but after several turns in the up direction. 4. Friction Last important point to take into account is friction: - friction between cord and fabric or slats, - friction in bearing, - friction in guides.

DMKI - DIVE 11R2