25.3/642 25.3/642 25.3/642

2.91/74

.98/24 White Button 2.48/63

Do Not Wire in Parallel

LT60 FTS
655A2 FTS 27.3/684 26.7/677
2 Mounting Holes for Self-Tapping Screw Dia. 5 mm (Cat. # 4000551) Depth 13 mm Spaced 1.89" (48 mm) Apart
WIRING COLOR CODE FOR FTS 50/60
5 White Black Red Green Grey Neutral White Button Yellow Button Ground Brake

SLT60*

660R2 SLTL 660R2 SLTR

28.9/734 28.9/734

28.2/717 28.2/717
SLT of push buttons is: blue & yellow * (left color code white & blue (right version). version) &
NOTE: Dimensions in millimeters are more accurate. X dimension refers to the length of the motor tube and drive assembly. Y dimension refers to the distance for mounting the pop rivets.

2.36/60

1.85/47

1.5\38

SOMFY LT50/LT60 CMO, LT50 RH, LT50 ILT RH and LT50 ILT

LT50 CMO

MOTOR TYPE X in. / mm Y in. / mm

.96/24

525A2 CMO 530R2 CMO 535A2 CMO 540R2 CMO 550R2 CMO
23.39/594 23.39/594 26.14/664 26.14/664 26.14/664
22.80/579 22.80/579 25.55/649 25.55/649 25.55/649

LT50/60 CMO

.48/12.79/20

2.13/54 1.64/41.7

1.81/46 1.57/40
See Note for Tube Diameter

LT60 CMO

.98/25

1.57/40 1.57/40

660R2 CMO 25.4/646 680R2 CMO 26.8/681 6100R2 CMO 26.8/681
24.8/630 26.2/665 26.2/665

White Black Red Green

Neutral White Button Ground Yellow Button

WIRING COLOR CODE

NOTE 1: LT50 Tube Diameter = 1.85"/47 mm LT60 Tube Diameter = 2.36"/60 mm
Center Line of Override Shaft HEX.275/7 or SQUARE.236/6

LT50 RH

504S2 RH 506S2 RH 510S2 RH 515S2 RH 520R2 RH 19.9/505 20.7/525 21.9/555 23.8/605 20.7/525 19.3/490 20.1/510 21.3/540 23.2/590 20.1/510

.2.0/49.6.16/3.9

Mounting Hole.80/20 Deep
2 Mounting Holes for Self-Tapping Screw Dia. 4 mm (Cat. # 4000555) Depth 9 mm, Spaced 1.14" (29 mm) Apart

After choosing the roller tube and the chart corresponding to your type of slat (see pages 17-20), select the operator according to the weight and the total height of the shutter ( the safety factor is included in these charts).
TORQUE REQUIREMENT DIAGRAM
Torque Actual Motor Torque Required Safety Margin (allowing for friction and misalignment)

Torque Variations

Theoretical Torque

Number of Turns

A. The initial torque required to start lifting the slats is small. However, it increases rapidly. This results from the motor lifting the load of the slats away from the bottom of the application. B. All slats are hanging free. The torque may slightly decrease while the slats are rolling up, since the tube radius has not yet increased. C. The maximum torque required is arrived at when the slats are lifted up about one third of the way from the bottom of the application. D. The torque decreases progressively and reaches a minimum when the shutter is fully rolled up.
After choosing the roller tube and the page corresponding to your type of slat, select the operator according to the weight and the total height of the shutter (A safety factor is included in these charts).
TYPE OF SLAT: HEIGHT 1.44" TO 1.50" (36/38 mm) THICKNESS.340" TO.355" (9 mm)

HEIGHT: 0 TO 5 FT.

kg. TYPE OF TUBE OCTA. 40 ROUND 2.5" (63.5) OCTA. 60 Round 70 OCTA. 70 Round 75 ROUND 3.5" (89) lb. 173 380

510R2 510R2 510R2 510R2

520R2 520R2 520R2 520R2

530R2 530R2 530R2 530R2

540R2 540R2 540R2 540R2

550R2 550R2 550R2

660R2 660R2 660R2 660R2

680R2 680R2 680R2 680R2

6100R2 6100R2 6100R2

6100R2

HEIGHT: 5 FT. TO LESS THAN 8 FT.

404R2 409R2

550R2 550R2 550R2 550R2
6100R2 6100R2 6100R2 6100R2
HEIGHT: 8 FT. TO 11.5 FT.
TYPE OF SLAT: HEIGHT 1.58" TO 1.65" (40/42 mm) THICKNESS.340" TO.355" (9 mm)
kg. TYPE OF TUBE ROUND 2.5" (63.5) OCTA. 60 Round 70 OCTA. 70 Round 75 ROUND 3.5" (89) lb. 173 380

660R2 660R2

680R2 680R2 680R2
TYPE OF SLAT: HEIGHT 1.986" TO 2.10" (50/53 mm) THICKNESS.55" (14 mm)
510R2 520R2 530R2 510R2 520R2 530R2 510R2 520R2 530R2

540R2 550R2 540R2 550R2 540R2 550R2 550R2

510R2 520R2 530R2 540R2

TYPE OF SLAT: HEIGHT 2.125" TO 2.20" (54/56 mm) THICKNESS.55" (14 mm)

HEIGHT: 0 to 5 FT.

kg. TYPE OF TUBE OCTA. 60 Round 70 OCTA. 70 Round 75 ROUND 3.5" (89) lb. 173 380

510R2 510R2 510R2

520R2 520R2 520R2

530R2 530R2 530R2

540R2 540R2 540R2
510R2 520R2 510R2 510R2 520R2 520R2

660R2 660R2 660R2

510R2 520R2 530R2 510R2 520R2 530R2

540R2 550R2 540R2 550R2

510R2 520R2 530R2 540R2 550R2
For Window Coverings (Roll-up Applications)
kg. TYPE OF TUBE ROUND 29 mm lb.
kg. TYPE OF TUBE ROUND 40 mm ROUND 2.0" (50.8) ROUND 2.5" (63.5) lb.

404S2 404S2 404S2

OTHER LS40 RANGE MOTORS OTHER LS40 OR LT50 RANGE MOTORS OTHER LS40 OR LT50 RANGE MOTORS
kg. TYPE OF TUBE ROUND 2.0 (51) ROUND 2.5" (63.5) ROUND 3.0 (76) ROUND 3.5" (89) lb.

45 100

55 120

64 140

73 160

82 180

504S2 504S2 504S2 504S2
506S2 506S2 506S2 510S2 510S2

510S2 515S2 515S2 515S2

OTHER LT50 RANGE MOTORS OTHER LT50 RANGE MOTORS OTHER LT50 RANGE MOTORS

OTHER LT50 RANGE MOTORS

For Interior Window Coverings
PLEATED, CELLULAR AND ROMAN

Motor Type

Output Drive (Hexagonal Shaft)
Single Single Double Double
Maximum area for Pleated Shades Sq. Ft.
60 Sq. Ft. 90 Sq. Ft. 60 Sq. Ft. 120 Sq. Ft.
Maximum area for Cellular Shades Sq. Ft.
53 Sq. Ft. 75 Sq. Ft. 53 Sq. Ft. 105 Sq. Ft.

Roman Shades Lbs.

4.25 Lbs. 7.5 Lbs. 4.25 Lbs. 8.5 Lbs.
Maximum height with 1.4 mm cord
11.5 Ft. 11.5 Ft. 11.5 Ft. 11.5 Ft.

Speed (RPM)

LV 25-B44 LV 25-B64 LW 25-B44 LW 25-B83
Specifications based on motors used with (CTS). They are approximate and may vary depending on product application, fabric etc.

Output Drive

120 Sq. Ft. >120 Sq. Ft. >120 Sq. Ft.
105 Sq. Ft. >105 Sq. Ft. >105 Sq. Ft.

8.8 Lbs. 21 Lbs. 42 Lbs.

13 Ft. 18 Ft. 19.8 Ft.

LT28 LS40* LT50**

Tubular Tubular Tubular
* LS40 Based on use of 404S2 ** LT50 Based on use of 510S2

HORIZONTAL BLINDS

Maximum area for 25 mm Aluminum blinds ( Sq. Ft.)
22 Sq. Ft. 44 Sq. Ft. 22 Sq. Ft. 54 Sq. Ft.
Maximum area for 50 mm Wood blinds ( Sq. Ft.)

NA NA NA 27 Sq. Ft.

Maximum height with O 1.4 mm cord ( Ft.)

FABRIC

FABRIC MOTOR

ELECTRONIC CONTROL

For the 525A2 FTS motor, the entire FTS system must be able to withstand a minimum of 250 Lbs. of force. This value was obtained based on both the fabric tube and strap tube having a diameter of 2.5. For the 655A2 FTS motor, the entire FTS system must be able to withstand a minimum of 500 Lbs. of force. This value was based on both the fabric tube and strap tube having a diameter of 3.5.

LOAD BAR

STRAP MOTOR
NOTE: The SOMFY FTS System is a specialized system and should not be installed without proper training from a SOMFY technician.

POWER SOURCE 120V AC

SWITCH
For a quick reference guide to our installations, refer to page 26 and 27 of this catalog. The complete instructions are available on our website at www.somfysystems.com under the Technical Documentation section.
SLT and OREA RTS Motors SLT
The SLT Range is made exclusively for cassette awnings. What separates the SLT from a standard LT is the onboard control which detects when a cassette is almost closed and reduces the torque of the motor for the last few inches of travel. Then when the headrail meets the cassette, the on-board control shuts the motor off. The combination of digital control plus a reduced-torque closing provides the maximum protection against fabric stretch. For more information, turn to page 66.

OREA RTS

The new radio version of the SLT motor is the OREA RTS. This motor can be mounted on the left or right side of the cassette awning and is compatible with the RTS sensors. It features an integrated radio receiver with remote limit setting and a remote user programmable intermediate stop. 24
FTS Motor Selection Guide
This motor chart was created based on experimental results. The following tube diameters were used:
LT50 LT60 FABRIC TUBE O70 O78 STRAP TUBE O63 O63

WIDTH LENGTH/PROJECTION

13.1ft

16.4ft

19.6ft

22.9ft

26.2ft

29.5ft 32.8ft

3.2ft 1m 6.5ft 2m 9.8ft 3m 13.1ft 4m 16.4ft 5m 19.6ft 6m 22.9ft 7m 26.2ft 8m 29.5ft 9m 32.8ft 10m 36ft 11m 39.3ft 12m

10.7 ft2

21.5 ft2

32.2 ft2

43.0 ft2

53.8 ft2

64.5 ft2

75.3 ft2

86.1 ft2

96.8 ft2

107.6 ft2

129.1 ft2

150.7 ft2

172.2 ft2

193.7 ft2

215.2 ft2

FTS 25/20
96.8 ft2 129.1 ft2 129.1 ft2 172.2 ft2

161.4 ft2

226.0 ft2

258.3 ft2

290.6 ft2

322.9 ft2

301.4 ft2

344.4 ft2

387.5 ft2

430.5 ft2

269.1 ft2

FTS 55/20

376.7 ft2 452.1 ft2

FABRIC MOTOR Fabric Winding Gray Green White (not connected) Tester Cable Black Gray Green White Red STRAP MOTOR (not connected) Gray Green White Strap Winding
Setting the Limits for the first time
Both limits must be set on each motor. Use the Limit Setting chart below to determine the order in which the limits are set for a given motor and fabric orientation. 1. Unwind the fabric using the tester cable (fig. 2). When the desired position is reached, set the strap tube limit by pressing and releasing the PRIMARY limit (1) on the strap motor tube. Then press and release the SECONDARY limit (2) on the fabric motor. 2. Using the tester cable, wind the fabric around the fabric tube (fig. 3). When the desired position is reached, press and release the PRIMARY limit (3) on the fabric motor tube. Then press and release the SECONDARY limit (4) on the strap motor. 3. Before connecting the motors to the controller, run the system (using the tester cable) in both directions to verify that the system works correctly. NOTE: If any limits need to be readjusted, be sure to re-set both the primary and secondary limits for the system in the correct order as described above.
Limit Setting Order According to Motor Configuration

Fig. 2

Secondary Limit

Primary Limit

Tester Cable

RED Dynamic Tension

BLACK Dynamic Tension Use wire nuts to cap off unused leads

Fig. 3

BLACK Dynamic Tension

Dynamic Tension

Use wire nuts to cap off unused leads
B. INSTALLATION CONFIGURATIONS
Below are the Four Motor Configurations that are possible with the FTS System: The different configurations each require a unique instruction for wiring and limit setting. Wiring Identification The tables below the illustrations describe the wiring scheme with FTS control terminal identification based on the motor and fabric orientation above it. NOTE: The illustration on top is configured exactly the same as the one below it, only flipped over to visually illustrate the fabric rolling above or below the tube.
FABRIC MOTOR STRAP MOTOR STRAP MOTOR
FABRIC MOTOR FABRIC MOTOR

STRAP MOTOR STRAP MOTOR

MOTOR HEADS

WIRING

White Black Red Gray Green

TERMINAL #

* Common Winding Tension Brake Ground
White Red Black Gray Green

* USE GROUND BAR

Common Winding Tension Brake Ground

C. FINAL CONNECTIONS

All wiring must conform to NEC (National Electrical Code) and local codes. Before connecting the operators to the electronic control, set the tension adjustment potentiometers to "0" and ensure that all the dip switches are in the "off" position. Referring to charts above, connect the motors and switch to the electronic control as shown in the diagram to the right. Check that the system operates correctly with respect to the switch directions. Make sure the limits have been properly set. At this point, there may be some fabric sag - this is normal. To finish the installation, set both the dynamic and final tension adjustment potentiometers to a minimum value of 5. This will remove all the fabric sag in the system and ensure proper operation of the FTS installation.

6051003

Long Shaft Adaptor for 5 mm Hexagonal

6050002

Shaft Adaptor for 5 mm Square

6050001

Shaft Adaptor for 6 mm Hexagonal

6051001

Long Shaft Adaptor for 6 mm Hexagonal

AMS 25

6050000
Adjustable Mechanical Stop (AMS)

6050666

Wall Mount Brackets for RDS/RTS Control

6050403

Ladder Braid Crimps

6050026

29 mm Round Tube (Max. 16 ft.)

6050029

NEW 29 mm Tube w/"Grooved" Surface (Max. 20 ft.)

6180029

NEW CTS29 w/New Molded Cradle Assembly Kit

6070029

NEW Molded LT28 Motor/Idler Brackets

6050129

NEW 45 x 51 mm Extruded Aluminum White Headrail (Max. 20 ft.)

6080029

NEW Headrail Mounting Brackets

6050290

NEW Headrail Side Caps

End Cap for 29 mm Tube

6050411
Decorative Tape Adaptors for (1) Cotton Tape

6050412

Decorative Tape Adaptors for (1.5) Cotton Tape

6050406 6050505

5 mm Hex Shaft for CTS (16 Ft. Maximum Length) 6 mm Hex Shaft for CTS (6 Ft. Sections)

6050400

Stop Collar Ring for 5 mm Hex Shaft

6050401

Stop Collar Ring for 6 mm Hex Shaft
DC Motor Cord Take-Up Systems (CTS)

6180367

29 mm Cone and Ring (Kit)
CTS 29 mm for SOMFY 46 x 51 mm Headrail

6180389

CTS 25 (Kit) for Standard 1" x 1" Headrail (5 mm Hex Shaft)

6180393

CTS 25 (Kit) for Standard 1" x 1" Headrail (5 mm Sq Shaft)

6180395

CTS 25 (Kit) for Standard 1" x 1" Headrail (6 mm Hex Shaft)

6180396

CTS 25 (Kit) for Classic Supreme Headrail (5 mm Hex Shaft)

6180394

CTS 25 (Kit) for Classic Supreme Headrail (6 mm Hex Shaft)

6180397

CTS 25 (Kit) for VersaRail/Easy-Up/EasyGlide (5 mm Hex Shaft)

6180398

CTS 25 (Kit) for VersaRail/Easy-Up/EasyGlide (6 mm Hex Shaft)

6180407

CTS 25 (Kit) for LightLines (5 mm Hex Shaft)

6180408

CTS 25 (Kit) for LightLines (6 mm Hex Shaft)

6180404

CTS 25 (Kit) for GutterRail/Low Profile 2 Headrail (5 mm Hex Shaft)

6090186

6080040
LS40 Idler Bracket (for 8 mm shaft) - Decorative white composite - Maximum motor torque - 4Nm (removable parts must be screwed together, see enclosed instructions). - Maximum system load - 17 Kg. (38 Lbs.)(must be screwed together) - Compatible with motor bracket Cat. #6070040

6070040

LS40 Radial Square Motor Bracket - Decorative white composite - Maximum motor torque - 4Nm (removable parts must be screwed together, see enclosed instructions) - Maximum system load - 17 Kg. (38 Lbs.)(must be screwed together) - Compatible with idler bracket 6080040

O 50 Pull String

6050040
LS40 Intermediate Bracket - Decorative white composite - Maximum motor torque - 4Nm (removable parts must be screwed together, see enclosed instructions). - Maximum system load - 17 Kg. (38 Lbs.)(must be screwed together) - Any LS40 drive wheel may be used to adapt to any tube profile - Pull string used to disengage intermediate connection

6090040

LS40 Idler End Cap with 8 mm Diameter Pin - Decorative white composite - Maximum motor torque - 13Nm - Any LS40 drive wheel may be used to adapt to any tube profile - Maximum system load - See note below

6180391

CTS 40 Kit for GutterRail 2 x 2 1/4 Headrail

6050521

40 mm Octagonal Tube (Sold in 20 ft. lengths)

6050410

2 Slat Clips for Wood Blinds (White) 2 Slat Clips for Wood Blinds (Ivory) 2 Slat Clips for Wood Blinds (Brown)

6050089

40 mm Fabric Clip

6080251

LS40 Motor/Idler Bracket for 2 x 2 1/4 GutterRail Headrail - requires 2 screws (4000555 not included)

Crowns and Drives

Dimensions (mm) Cat. Number

6061286

LS40 Crown for 40 x 0.8 mm Octagonal Tube LSmm Octagonal Set LS40 Drive for 40 x 0.8 mm Octagonal Tube

6061284

LS40 Crown for (40 x 1.5 mm) Tube LSmm Round Set LS40 Drive for (40 x 1.5 mm) Tube

6061310

LS40 Crown for (40 x 1.0 mm) Tube

6061309

LS40 Drive for (40 x 1.0 mm) Tube
LT50/60 Mechanical Accessories

Motor Brackets

6070003

6070499

Universal Bracket with Spring Ring - Assembled to accept Inch Series threaded screws 1/4 - 20, 5/16 - 18 (nuts molded into bracket) Universal Bracket with Spring Ring - Zamak Material - 2 holes for M6 hex or 1/4 - 20 flat head screw on 48 mm diameter - 2 holes for M8 hex screw on 60 mm diameter - 2 countersunk holes for M8 screw on 60 mm diameter - Lateral space requirement for installation: 27 mm - Maximum motor torque - 85 Nm or 100 Nm when used with locking spring ring Cat. No. 4350027, and 5/16 - 18 or M8 bolts without molded nuts - Maximum system load - 200 Kg. (441 Lbs.) when used with locking spring ring Cat. #4350027 With M8 and M6 nuts molded in bracket - Same as above - Maximum system load 200 Kg. (441 Lbs.)

6070501

Spring ring needs to be replaced with locking spring ring Cat. #4350027 to obtain maximum torque and load capability

6070502

6070500
Weld-on Bracket Without Spring Ring - Steel bracket without surface treatment - For welding to mounting plates of all kinds. Lateral space requirement for installation: 23 mm + thickness of mounting plate - Must be used with spring ring Cat. No. 4350026 or locking spring ring Cat. No. 4350027 (not included) - Maximum motor torque - 85 Nm or 100 Nm depending on spring ring and quality of weld - Maximum system load - 200 Kg. (441 Lbs.) when used with locking spring ring Cat. #4350027

6070504

Heavy Duty Angle Plate with Universal Motor Bracket - With two M8 screws and nuts included - Angle plate (zinc-plated steel) - Three adjustment positions possible - Maximum motor torque - 85 Nm or 100 Nm when used with locking spring ring Cat. #4350027 - Maximum system load - 130 Kg. (287 Lbs.) or 200 Kg. (441 Lbs.) when used with locking spring ring Cat. #4350027 Heavy Duty Angle Plate - Same as above but without the universal motor bracket Motor Bracket With Spring Ring (120 mm x 120 mm) - Four mounting holes provided - Zinc-plated steel - Lateral space requirement for installation: 28 mm - Maximum motor torque - 85 Nm - Maximum system load - See note below Motor Bracket With Spring Ring (100 mm x 100 mm) - Four mounting holes provided with a through hole in the center of the bracket - Zinc-plated steel - Lateral space requirement for installation: 28 mm - Maximum motor torque - 85 Nm - Maximum system load - See note below

6080262

White Dress Cover for Idler Brackets 6080254, 6080255 and motor brackets 6070082, 6070513 - White composite - Replaces SOMFY Cat. No. 6080252

6080256

Heavy Duty Idler Bracket with Idler End Cap Holder - Two screws and cotter pin included - Zinc plated steel, gauge 3(0.2391 in.) - Used with end cap having stationary 16 mm diameter shaft - Maximum motor torque when properly installed with cotter pin: - FTS range - 55 Nm - LT range - 100 Nm - Maximum system load - 200 Kg. (441 Lbs.)

6080257

Idler End Cap Holder - Zinc plated steel - Compatible with bracket (Cat. No. 6070506) - Used with end cap having stationary 16 mm diameter shaft - Maximum motor torque when properly installed with cotter pin: - FTS range - 55 Nm - LT range - 100 Nm - Maximum system load - 200 Kg. (441 Lbs.) - Open end of the U must face up

6080528

U Shaped Idler Bracket - Zinc plated steel - Idler bearing securing screw included - Maximum motor torque - 40Nm - Maximum system load - 115 Kg. (254 Lbs.)

6080529

Idler Bearing (for O 12mm Shaft) - Nylon - Maximum motor torque - 40Nm - Compatible with #6080528 - Maximum system load - 115 Kg. (254 Lbs.)

Intermediate Brackets

6050256
Heavy Duty LT Intermediate Support Bracket - Will adapt to any tube profile using tube matching LT drives - The 4 drives are not included and must be specified separately - Maximum motor torque: FTS range - 55 Nm, LT range - 100 Nm - Heavy gauge 3(0.24 in.), zinc plated steel - Extruded aluminum shaft with heavy duty roller bearing - Maximum system load - See note below Light Duty LT50 Intermediate Support Bracket for a 2" Tube - Maximum torque - 50 Nm - Zinc plated steel - Adjustable ball bearing location - 2 adjustable cast aluminum drives included along a steel shaft - Maximum system load - See note below LT50 Intermediate Bracket with 16 mm ID Bearing - Zinc plated steel - Cat. No. mm bearing plate also sold separately - Cat. No. 6090252 square shaft also sold separately - Maximum motor torque: FTS range - 25Nm, LT50 range - 50Nm - Maximum system load - 69 Kg. (152 Lbs.) LT50 Adjustable Intermediate Support Bracket for a 2" Tube - Zinc plated steel bracket - Cast aluminum drives, with set screw - set screw must use lock tight to prevent screw from vibrating free - Maximum motor torque: FTS range - 25Nm, LT50 range - 50Nm - Maximum system load - 69 Kg. (152 Lbs.) LT50 Adjustable Intermediate Support Bracket for a 2.5" Tube LT Intermediate Bracket for 2" Tube Only - Zinc plated steel bracket - Composite end caps - Maximum motor torque - 15 Nm - Requires properly notched 2 tube for transfer of torque - Recommended tube used included with 2 LT drives - Maximum system load - 69 Kg. (152 Lbs.) - Compatible with LT brackets 6070082,6080254, and 6080255 LT50 Flexible Intermediate Bracket Kit for 2" Tube - Maximum angle up to 30o - Maximum effective motor torque - 7 Nm - Zinc plated steel bracket - Cast aluminum drives and flexible coiled steel shaft - Maximum system load - 28 Kg. (60 Lbs.) - Same as above except for maximum angle up to 450

4350036

6020086

6020087

6180500

CTS 50 Kit

6050185

Headrail for CTS 50

6050186
Headrail Cover for CTS 50

6050184

Finished Side Caps for CTS 50 Headrail

6080183

Headrail Mounting Brackets

6050090

O 1.5 mm
Fabric Fastening Clip for 2" (50 mm) O.D. Tube - Made out of spring steel

6050102

Fabric Fastener for 2.5" (63 mm) O.D. Tube

Cables and Miscellaneous

Standard Motor Cables Without Plug (4 wire)
LT Motor Cable - 6 Ft. LT Motor Cable - 12 Ft. LT Motor Cable - 24 Ft. LT Motor Cable - 6 Ft. long with waterproof plug
LT RTS and ILT Motor Cables Without Plug (3 wire)
6020542 LT Motor Cable - 3 Ft. LT Motor Cable - 6 Ft. LT Motor Cable - 12 Ft. LT Motor Cable - 18 Ft. LT Motor Cable - 24 Ft.
LT RTS and ILT Motor Cables With Plug

6020549

O (O 130 for 6050326)
Plug-in Cable with 5-15P NEMA Plug - 3 Ft. Plug-in Cable with 5-15P NEMA Plug - 6 Ft. Plug-in Cable with 5-15P NEMA Plug - 12 Ft. Plug-in Cable with 5-15P NEMA Plug - 18 Ft. Plug-in Cable with 5-15P NEMA Plug - 24 Ft. 50 x 1.5 mm (approx. 2") Tube Cord Take-up Reel - Material - Cast aluminum alloy - Shipped unassembled in 4 pieces - Adjustable tape width 63 x 1.5 mm (approx. 2.5") Tube Cord Take-up Reel 2" Tube Take-up Reel (outside dia. 89mm) - Material ABS - Maximum tape width - 9 mm 40mm tube take-up reel (outside dia. 66mm)

6050337

6050326 6050517

6050519

Anti-Blocking System (ABS)
ABS Wheel - Left Rotation - Maximum motor torque - 30 Nm ABS Wheel - Right Rotation - Maximum motor torque - 30 Nm The input of the ABS wheel fits the LT50 motor shaft. The output shaft will accept any of the LT50 drive wheels. Drive retaining washer is included. In the up direction, 30 Nm can be lifted. If an obstacle is detected in the down direction then the motor will spin freely and not damage the product. A momentary switch or Somfy controls having 3 min. time out are required. Same as above but with greater torque threshold which is required to activate the ABS - CMO ABS left rotation - maximum motor torque - 30 Nm - CMO ABS right rotation - maximum motor torque - 30 Nm

6061303 6061305

Tube Profiles Cat. Number Description

6250712

LT CMO Awning Eye Compatible with Geiger Crank Handles - Length of the shaft is (100 mm) 4" - Stainless steel pin for eyepiece mounting to 7 mm Hex shaft - Stainless steel stop washer & socket head screw (also sold separately) - Zinc plated steel shaft - Stainless steel lock washer - Stainless steel M4 socket head screw CMO Extension Shafts - 7 mm Hex, 8.66" (220 mm) long - Zinc plated steel - 7 mm Hex, 13" (330 mm) long - Zinc plated steel Connecting Sleeves - 7 mm Hex to diameter 11.3 mm - Zinc plated steel - 7 mm Hex to 8 mm Square - Zinc plated steel - 7 mm Hex to 7 mm Hex - Zinc plated steel CMO Extension Shaft with Universal Joint - Shaft 7 mm Hex, 12.4" (315 mm) long - zinc plated steel - Output of the universal joint is a 12 mm diameter hole - Universal joint - White powder coated steel - Color: white fixing plate - 60o outlet

6250715

6250716

6250717

6250718 6250719

6250720

6250721
CMO Extension Shaft with Awning Eye and Plate - Shaft 7 mm Hex, 10.25" (260 mm) long- Zinc plated steel - Color: white fixing plate with black awning eye - 60o outlet

6250723

LT CMO 70 Degree, 4 Hole Plate SS Crank Handle Universal Joint - Compatible with 14 mm diameter bell type connectors - Material: Stainless steel and nickel plated zinc casting plate - 7 mm hex shaft: Steel, zinc plated

6250724

LT CMO 90 Degree, 2 Hole Plate SS Crank Handle Universal Joint - Material: Stainless steel and nickel plated zinc casting plate

6250725

LT CMO 90 Degree, 4 Hole Plate SS Crank Handle Universal Joint

6250730

7 mm Hex to 7 mm Hex Universal Joint Adaptor

6250731

7 mm Hex to 8 mm Square Universal Joint Adaptor

6250732

7 mm Hex to 8 mm Square Double Universal Joint Adaptor
LT50/60 and LT50/60 CMO Mechanical Accessory Kits
Product Kit Cat. Number Description of Parts Quantity
U.S. 3/4 inch SS Hardware Kit
1/4 - 20 x 3/4 hex head SS 18-8 bolt 1/4 flat washer SS 18-8 1/4 split lock washer 18-2 2
U.S. 1 inch SS Hardware Kit
1/4 - 20 x 1 hex head SS 18-8 bolt 1/4 flat washer SS 18-8 1/4 split lock washer 18-2 2
U.S. 1.25 inch SS Hardware Kit
1/4 - 20 x 1.25 hex head SS 18-8 bolt 1/4 flat washer SS 18-8 1/4 split lock washer 18-2 2
Metric 20 mm SS Hardware Kit
M6 x 20 mm hex head cap screw SS Lock washer split M6 SS A2 M6 flat washer SS A2 2
Metric 25 mm SS Hardware Kit
M6 x 25 mm hex head cap screw SS Lock washer split M6 SS A2 M6 flat washer SS A2 2
Metric 30 mm SS Hardware Kit
M6 x 30 mm hex head cap screw SS Lock washer split M6 SS A2 M6 flat washer SS A2 2

670013 100405A 9703956 9910004

9001264 9203887

9000980

9163325 9163334

Cat. No. 6061126 6061216

2005 No. 9500687 9138028

Description LS 40 Intermediate Bracket Fabric Clip for 40 mm Tube Fabric Fastener for 2" (50 mm) O.D. Tube Fabric Fastener for 2.5" (63 mm) O.D. Tube 45 x 51mm Extruded Aluminum White Headrail (max. 20 Ft.) CTS 50 Headrail Mounting Brackets CTS 50 Headrail Finished Side Caps Headrail for CTS 50 Headrail Cover for CTS 50 Heavy Duty LT Intermediate Support Bracket Light Duty LT50 Intermediate Support Bracket for a 2" Tube Headrail Side Caps 63 x 1.5 mm (approx. 2.5") Tube Cord Take-up Reel 50 x 1.5 mm (approx. 2") Tube Cord Take-up Reel LT50 Intermediate Bracket with 16 mm ID Bearing LT50 Adjustable Intermediate Support Bracket for a 2" Tube LT50 Adjustable Intermediate Support Bracket for a 2.5" Tube Stop Collar Ring for 5 mm Hex Shaft Stop Collar Ring for 6 mm Hex Shaft Ladder Braid Crimps 5 mm Hex Shaft for CTS (16 Ft. Maximum Length) 6 mm Hex Shaft for CTS (7 Ft. Sections) 2 Slat Clips for Wood Blinds (White) 2 Slat Clips for Wood Blinds (Ivory) 2 Slat Clips for Wood Blinds (Brown) Decorative Tape Adaptors for 1 Cotton Tape Decorative Tape Adaptors for 1.5 Cotton Tape Idler End Bearing Support for 16 mm Dia. Shaft 6 mm Hex Shaft for CTS (5 Ft. Sections) 2 Tube Take-up Reel 40 mm Tube Take-up Reel 40 mm Octagonal Tube LT Intermediate Bracket for 2 Tube Headrail Adaptor for GutterRail/Low Profile 2 Headrail Headrail Adaptor for SureClose Headrail Headrail Adaptor for EasyRise (New Version) Wall Mount Brackets for RDS/RTS Control Long Shaft Adaptor for 6 mm Hexagonal Long Shaft Adaptor for 5 mm Hexagonal 2.75 Round LT50 Crown 2.75 Round LT60 Crown 70 mm Octagonal LT60 Crown DS 70 LT Drive (1.2 -1.5 mm wall thickness) P72 LT60 Crown DS 70 LT50 Crown DS 78 LT60 Crown 3.5 Round LT60 Crown 3.5 Round LT50 Crown DS 74 LT50 Crown DS 78 LT50 Crown I65 LT50 Crown DS 78 / R LT60 Crown 4.0 Round LT60 Crown 4.0 Round LT60 Set I85 LT60 Crown I85 LT60 Set DS 78 / D LT60 Crown DS 85 LT60 Crown

Page 53 53

9002541

9162258 9162257

9146011

9707639 9705776

Cat. No. 6061401 6061402

2005 No. 9147545 9147327

Description DS 85 LT50 Crown Ls40 Drive for (40 x 1.5 mm) Tube LS40 Crown for (40 x 1.5 mm) Tube LS40 Drive for (40 x 0.8 mm) Octagonal Tube LS40 Crown for (40 x 0.8 mm) Octagonal Tube LSmm Round Set LSmm Octagonal Set Flush Mount Bracket for LT28A and LT28B Motors ABS Wheel-Left Rotation ABS Wheel-Right Rotation CMO ABS Wheel-Left Rotation CMO ABS Wheel-Right Rotation LS40 to LT50 Adaptor Kit LS40 Drive for (40 x 1.0 mm) Tube LS40 Crown for (40 x 1.0 mm) Tube 2.5 Round LT Drive (63 mm x 1.5 mm) - Soft Clip 2.5 Round LT Drive (63 mm x 1.5 mm) - Hard Clip 2.75 Round LT Drive (70 mm x 1.5 mm) - Hard Clip 3.5 Round LT Drive (89 mm x 1mm) 3.5" Round LT Drive (89 mm x 2 mm) 4.0 Round LT Drive (102 mm x 2 mm) 70 mm Octagonal LT Drive P72 LT Drive DS 78/R LT Drive DS 78 LT Drive DS 78/D LT Drive DS 85 LT Drive I85 LT Drive 70 mm Octagonal, Aluminum LT50/60 Drive Wheel Kit 2 Round LT50 Drive (50 mm x 1.5 mm) - Soft Clip 2 Round LT50 Drive (50 mm x 1.5 mm) - Hard Clip 2.5 Round LT50 Set - Hard Clip 2.75 Round LT50 Set 2.75 Round LT Drive (70 mm x 1.5 mm) - Soft Clip 60 mm Octagonal LT50 Set 60 mm Octagonal LT Drive 70 mm Octagonal LT50 Set P72 LT50 Set 3.5 Round LT50 Set DS 70 LT50 Set DS 70 LT Drive (0.8 -1 mm wall thickness) DS 74 LT50 Set DS 74 LT Drive DS 78 LT50 Set I65 LT50 Drive I65 LT50 Set SM 65 LT50 Crown - 3 grooves SM 65 LT Drive AMA71 LT50 Drive AMA71 LT50 Crown LT60 Crown (78 mm Dia.) LT60 Drive (78 mm Dia.) 2 LT Drive for CTS 50 Tube 50 mm Octagonal LT50 Crown 50 mm Octagonal LT50 Drive 2.75 Round LT60 Set 70 mm Octagonal LT60 Set 3.5 Round LT60 Set

2.1 DIMENSION CHART

APPLICATION Roller Blinds Motor Hardware System Maxi. Surface Maxi. Height 1.4 cord

LS 40 LT 50

Tube 40x1.5 Tube 50x1.5
Depending on fabric and botton bar weight
Aluminium Venetian Blinds
25 mm Alu. I_I 57xmm Alu. I_I 57xmm Alu. I_I Nichibe 70xmm Alu. I_I Nichibe 70x70

Wood Venetian Blinds

25 mm Wood I_I57xmm Wood I_I57xmm Wood I_I Nichibe 70xmm Wood I_I Nichibe 70x70 I_I 57x51 50x1.5 I_I Nichibe 70x70

LS 40 LT 50 LT 50

Depending on fabric weight
Maxi height: Maxi cord length. (Stack of slat to be deducted for maxi opening)
$ Internal test up to 4 m high
2.2 MOTOR SELECTION CHART

< Venetian blind >

2.2 MOTOR SELECTION CHARTS LS 40
Cord Venetian blinds with CTS 40
Bearing #9162145, Cone #9162144 $ Estimated maximum values, depending on type of fabric s, slats, bottom bar, hardware system.Consult Somfy for precise calculation
2.2 MOTOR SELECTION CHARTS LT 50 RH
Cord Venetian blinds with CTS 50
Bearing #9162241, Cover #9162242, Tilting rod #9162243, Cone #9162140 $ Estimated maximum values, depending on type of fabric s, slats, bottom bar, hardware system.Consult Somfy for precise calculation
Bearing #9162241, Cover #9162242, Tilting rod #9162243, Cone #9162240 $ Estimated maximum values, depending on type of fabric s, slats, bottom bar, hardware system.Consult Somfy for precise calculation

< Roller blind >

Crowns #9147330 and #9132143 Wheel #9147544 and #9132142 $ Estimated maximum values, depending on type of fabric s, slats, bottom bar, hardware system.Consult Somfy for precise calculation
Crown #9500343, Wheel #9500354 $ Estimated maximum values, depending on type of fabric s, slats, bottom bar, hardware system.Consult Somfy for precise calculation
Crown #9132138 Wheel #91321139 $ Estimated maximum values, depending on type of fabric s, slats, bottom bar, hardware system.Consult Somfy for precise calculation 26
Wheel #9206089 (Soft clip) or Wheel #9206088(Hard clip) $ Estimated maximum values, depending on type of fabric s, slats, bottom bar, hardware system.Consult Somfy for precise calculation
Crown #9147550 Wheel #9147340 $ Estimated maximum values, depending on type of fabric s, slats, bottom bar, hardware system.Consult Somfy for precise calculation 28

Crown #9500341 Wheel #9500340 $ Estimated maximum values, depending on type of fabric s, slats, bottom bar, hardware system.Consult Somfy for precise calculation 29
< Roman & Balloon blinds >
2.3 ASSEMBLY INSTRUCTIONS

< LS 40 >

a.PREPARING THE TUBE. - Cut the roller tube to the required length. Note: Take into account the installation width, the width of the motor head, the type of plug end and the bracket size. - De-burr the ends of the tube and ensure that the inside of the tube is clean. - Fit the plug end into the other end of the tube and secure with four steel pop rivets.
b.PREPARING THE TUBULAR MOTOR. - Place the crown wheel over the body of the motor and slide it over the raised key of the motors limit switch unit. - Place the drive wheel onto the output shaft of the motor.
c.FITTING THE MOTOR INTO THE TUBE. - Measure the drilling length as shown on the right. Do not drill into the motor output shaft. - Fit the motor into the tube, ensuring that the slot at the end of the tube slides over the key on the crown wheel. - Secure the drive wheel to the tube using 4 x 5mm steel pop rivets, placed at 120 from each other.

Attaching zone

Drilling length to measure
d.MOTOR END FITTING. - Three possible ways of fixing the motor head:
With 2 screws directly on the head
With a square shaft 10 mm rf. 9147334
With a flat <LO> bracket ref. 9147337
e.INSTALLING THE MOTORISED TUBE Note: Install the motor bracket on the same side as the power supply. - Fit the brackets, but do not tighten them. - Fit the plug end bracket over the plug end. - Ensure that the tube is horizontal using a spirit leveller. - Tighten the brackets once it is level. f. WIRING RECOMMENDATIONS The Electrical Supply Regulations 1988 give an Electricity Board the right to refuse to supply, or continue the supply to, a consumers installation which is not safe or which may cause interference with the supply to others. The Electricity Supply Regulations accept Regulations comply with all safety requirements. All electrical installations are governed by the IEE wiring regulations (16th edition).

Goupille ou vis

Square shaft ref. 500602 Motor bracket Plug end bracket

$ except US

Do not wire two or more motors to one switch without using a relay.
Do not use light switches. Do not wire two or more switches to one motor, without using relays approved by SOMFY. g.LIMIT SWITCH SETTING.
Two positions have to be set: the upper and lower limit position. This is where the awning, blind or roller shutter stops automatically: 1 - Ensure the switch is at the STOP position. 2 - Check that the: - Up button corresponds to the shutter or blind rolling up - Down button corresponds to the shutter or blind rolling down. If the rotational direction is incorrect, reverse the black and brown wires of the motor (connected to the switch).
SETTING THE STARTING POINT. - Before fitting the end product onto the tube, depress the DOWN button until the motor stops. The limit switch is pre-set at 3 turns. If a key way tube is used, place the key way facing outwards (towards yourself). To do this: Turn the DOWN thumbscrew. To identify the DOWN thumbscrew: check the direction the end product unwinds, find the arrow which points in the same direction (on the motor), the thumbscrew is located next to this arrow. Fix the fabric or shutter onto the tube, taking into account the direction the end product unwinds.

upper limit

lower limit
UP: Winding of the end product. DOWN: Unwinding of the end product.
UPPER LIMIT. Identify the UP thumbscrew which sets the upper limit. Find the arrows on the motor head which points the direction the motor rotates. Press the UP direction on the switch. The system would roll up. At this point, there are two possibilities: 1) The system stops short of the desired upper position. To adjust the blind up to the desired position, turn the UP thunbscrew in the positive direction while the switch is pressed UP, or 2) The system rolls beyond the desired upper position. Use the switch to roll the blind to the desired position or below the desired position. If the blind is below the desired position, refer to 1).
LOWER LIMIT. Identify the DOWN thumbscrew which sets the lower limit. Find the arrows on the motor head which points the direction the motor rotates. Press the DOWN direction on the switch. The system will roll down. At this point, there are two possibilities: 1) The system stops short of the desired lower position. To adjust the blind up to the desired position, turn the DOWN thumbscrew in the positive direction while the switch is pressed DOWN, or 2) The system rolls beyond the desired upper position. Use the switch to roll the blind to the desired position or below the desired position. If the blind is below the desired position, refer to 1).

h.DIAGNOSTICS. IF NOTHING WORKS, CHECK:
- that the power supply is switched on; also check fuses in the system. - that the control switch is wired correctly. - that the limit switches are set properly. - that the thermal protective device has not shut the motor off. If so, wait for the motor to cool down. - that the motor and switch has been wired correctly. Disconnect the switch and test the motor with a test cable.
IF THE SYSTEM DOES NOT STOP, CHECK:
- that the limit switch crown is being driven by the tube. - that the tube has been properly notched. - that the motor drive wheel is securely fastened to the tube. NB: if the motor is tested outside the tube, the crown wheel has to be manually turned in order to activate the limit switch unit and to stop the motor.

< CTS 40 >

A PART PREPARATION: a.Cut and punch the headrail in the same way as for a standard monocommand headrail. (N.B.: a cut-out is not necessary for the crank handle.)
PERMA headrail H.D. headrail
b.The CTS 40 bearing fits directly the PERMA 57 x 51 mm headrail standard cut-out. The standard H.D. 57 x 51 mm cuts-out have to be punched again with the special punching tool. 200.15 380.05
Cut-out Limit switch access holes: 6 mm
c.Drill the holes necessary for the motor and plug end bearings, and for access to the limit switch screws.
Plug end bracket holes: 4 mm
Motor bracket holes: 4 mm
d.Cut the 40 mm octagonal tube to size and deburr its extremities.
Lenght of tube (L) - 64 mm
e.Put the adaptor crown and wheel on to the motor. Screw the motor bearing onto the motor. Put the motor in down limit by supplying the motor and driving manually the crown adaptor in the down direction.
Caution: The ladder grip must be under the upper slat.

X mini

f.Cut the ladderbraids according to the slats width (see the chart below). Make a loop with the ladder grip.

LADDER GRIP

SLATS WIDTH LADDER LENGTH (X)

25 mm 195 mm

35 mm 200 mm

50 mm 210 mm

g.Tie a knot on the cone side. Cut the lifting cord to a length corresponding to the height of the blind (H) +160 mm. Make a mark on the bottom bar side at 110 mm + H for the knot.

B FINAL ASSEMBLY:

h Put in place the bearing into the headrail in the same direction as show below. The bearing can be positionned in two ways: however we advise to put all the bearings in the same way.

Take-up cord

i.Get the cords trough the bearings (and the stack of slats). When the stack of slats is assemble separatly from the headrail, take care the cord goes the rigth way in relation with the ladder braid.
j.Get the ladder braids trough the bearings (see detail below):
k.Put in place the cones. -The ladderbraids gets into the cone groove, and then, slide the cones into the bearing. -Let the cords hang on the same side of the bearing. Do not fix them onto the cones. -Turn the cones to align all the grooves with a cord attachment part on the top.

Groove

Ladder braid
l.a) Slide the tube into the cones (see detail on following page). Keep the attached part of the cone line up. b) Secure the cords onto the cones with the help of a screw driver.
Rotate each cone and align for tube insertion
Detail for tube insertion:
Two studs to spot the cone groove Cone

External groove of tube

m.Turn the tube one half a turn to get the cord knot at the bottom of the headrail. Insert the motor into the headrail and the tube. Insert the plug end. The plug end side gets opposite the holes drilled for access to the limit switches.

Motor Plug end

Plug end bracket
n.Insert the plug end bracket into the headrail and onto the plug end.
o.Tie a knot at the bottom end of the cord where the marks have been done.
p.Adjust the top limit and then readjust the bottom limit if necessary. Check and if necessary adjust the horizontality of the bottom bar. CAUTION: do not stack the slats completely, leave at least 25 mm, in up position.
Limit switch access holes

Motor bracket holes

p.Caution transportation packaging. Stacks of slats in the upper position with tight lifting cords.

< LT 50 RH >

a. PREPARING THE TUBE - Cut the tube to the required length, taking into account the width of the installation, the width of the head of the motor, the type of plug end and the size of the plug end bracket. - Deburr the ends of the tube & ensure that the inside of the tube is clean. - For all tube sizes up to & including 85mm diameter, cut a slot in the motor end of the tube to the dimensions shown. - For all tube sizes over 85mm you must form a tongue in the motor end of the tube by making two cuts 25mm apart & 20mm deep. - Fit the plug end into the other end of the tube & secure using 4 steel pop rivets.

2. up position

Remove the protective cap from head of motor
3. Depress fully both limit switch push buttons. They will auto-
matically lock in the down position. Operate the switch and check that the system operates correctly. If not put the switch to the off position, reverse the black & brown motor direction wires and try again.

down position

Identify the UP limit switch push button. Press the switch to the up direction until the required position is reached and put the switch in the off position Unlock the UP limit switch push button by depressing and releasing it Repeat the above operation to set the lower limit

BROWN WIRE

BLACK WIRE
7. Check with the switch that the motor stops at the up & down position just set 8.
Refit the protective cap. NOTE: Tubular motors are not continuously rated. They have a built-in thermal overload device which limits their operation to approximately 4 minutes.
f. TROUBLESHOOTING GUIDE NOTHING WORKS - Is the power supply switched on - check any fuses in the system? - Is control switch wired correctly? Refer to instructions. - Are limit switches set properly? Review limit switch settings. - The thermal protective device may have shut the motor off. Wait for the motor to cool down. - Check the wiring between the motor & the switch. - Disconnect the switch & test the motor with a test cable. THE SYSTEM IS NOT STOPPING - Is the limit switch crown wheel being driven by the tube (has tube profile been properly notched)? -Is motor drive wheel securely fastened to the tube. NB: if the motor is tested outside the tube, the crown wheel has to be manually turned in order to stop the rotation of the output shaft.

2.4 RECOMMENDATIONS

OCTOGONAL TUBES:
TO CHECK THE COMPATIBILITY OF A TUBE WITH CTS40, PLEASE USE THE ATTACHED DRAWINGS. THE DEPRAT TUBE 40 X 0,6 IS COMPATIBLE WITH CTS40, THE DEPRAT 40X 0,8 IS NOT COMPATIBLE.

FOR A GOOD TILTING:

LEAVE THE CORD SLACK IN DOWN LIMIT AND THE LOAD BAR BORNE BY THE LADDERBRAIDS. DO NOT FORGET TO PUT THE LADDERBRAIDS SLAT CLIPS. THE LADDERBRAIDS IS IMPORTANT. TO USE TOO THIN LADDERBRAIDS CAN CAUSE PROBLEMS.

FOR A GOOD LIFTING:

THE DIAMETER AND THE QUALITY OF THE LIFTING CORDS ARE VERY IMPORTANT. OUR TESTS HAVE BEEN CARRIED OUT WITH CORDS FROM JULIUS KOCH AND NIBROL. IN DOWN POSITION THE CORD MUST NOT MAKE ANY DEAD TURNS. TAKE CARE, DURING ASSEMBLY, NOT TO SCRATCH THE CONE FOR INSTANCE WITH A SCREWDRIVER. IN ORDER NOT TO WEAR QUICKLY THE CORDS, THE SLAT PUNCHES MUST BE OF GOOD QUALITY AND OF ADAPTED DIMENSIONS. PRIOR TO ASSEMBLY UNTWIST THE CORDS. TO BE 100% OF THE GOOD HORIZONTABILITY OF THE LOAD BAR AVOID TO MIX CONES FROM DIFFERENT BATCHES ON THE SAME BLIND. WE GUARANTY THE GOOD WORKING OF CTS40 ONLY WHEN THE HEADRAIL IS HORIZONTAL.

ASSEMBLY:

TO LIMIT FRICTION LEAVE A LARGE ENOUGH GAP BETWEEN PLUG END AND BRACKET. TO TAKE INTO ACCOUNT THE CORD DIMENSIONAL CHANGES, DO NOT STACK THE SLATS COMPLETELY. SET THE UP LIMIT AT 25 MM FROM THE HEADRAIL.

TRANSPORTATION:

THE BLINDS MUST BE DISPATCHED RETRACTED. ONCE FITTED, IN ORDER TO SUPPRESS ANY OVERLAPPING OF THE CORD, DRIVE THE BLINDS IN DOWN POSITION. IN ORDER TO CANCEL THE CORD OVERLAPPING, THE STACKS OF SLATS MUST BE CAREFULLY PACKED. (SEE ASSEMBLY INSTRUCTIONS)

ORDERS:

THE CONES AND BEARING CAN ONLY BE ORDERED AND SHIPPED IN BOXES OF 50 PIECES. MINIMUM LENGHT OF HEADRAIL WITH LS 40 + CTS 40: X MM

PART 3

CONTROLS

CHATRT

1 - EUROPEAN CONTROLS

page 54

3.1 EUROPEAN CONTROLS

One motor / one switch

Inis uno inteo 3 positions
One motor / one switch: (Tilt)
Inis uno inteo 5 positions
Group control / one switch (Up to 4 motors)
Group control / one switch (tilt)
Individual and group control with tilt function

Centralis IB

Individual and group control

Centralis uno IB

Centralis IB or Chronis IB

Centralis uno IB VB

Individual and group control with IR

One motor / sun control

Soliris sensor

Soliris uno

Individual and group control with sun function

Soliris IB

Individual and group radio control with SL 7070

Centralis indoor RTS

SL 7070 Drape

Centralis RTS

Telis 1 RTS

Telis 4 RTS

PART 4

REFERENCE LIST

1 - MOTORS 2 - MOTOR ADAPTERS 3 - CONTROLS 4 - CTS
page 60 page 64 page 68 page 71

4.1 MOTORS

- Tubular actuator: 230 V - 50 Hz - Torque 4 Nm speed 14 r.p.m. - Supplied without adapters. - Quantity per standard package: - Weight: 820 g - Tubular actuator: 230 V - 50 Hz - Torque 1.3 Nm speed 55 r.p.m. - Supplied without adapters. - Quantity per standard package: - Weight: 1000 g

MERCURE

- Tubular actuator: 230 V - 50 Hz - Torque 3 Nm speed 30 r.p.m. - Supplied without adapters. - Quantity per standard package: - Weight: 900 g
- Tubular actuator: 230 V - 50 Hz - Torque 9 Nm speed 14 r.p.m. - Supplied without adapters. - Quantity per standard package: - Weight: 1160 g

VULCAN

- Tubular actuator: 230 V - 50 Hz - Torque 13 Nm speed 8 r.p.m. - Supplied without adapters. - Quantity per standard package: - Weight: 1170 g

HERMES RH

- Tubular actuator: 230 V - 50 Hz - Torque 4 Nm speed 32 r.p.m. - Supplied without adapters. - Quantity per standard package: - Weight: 1720 g

ARIANE RH

- Tubular actuator: 230 V - 50 Hz - Torque 6 Nm speed 54 r.p.m. - Supplied without adapters. - Quantity per standard package: - Weight: 1720 g

JET RH

- Tubular actuator: 230 V - 50 Hz - Torque 10 Nm speed 54 r.p.m. - Supplied without adapters. - Quantity per standard package: - Weight: 1850 g

ATLAS RH

- Tubular actuator: 230 V - 50 Hz - Torque 15 Nm speed 32 r.p.m. - Supplied without adapters. - Quantity per standard package: - Weight: 1950 g

GEMINI RH

- Tubular actuator: 230 V - 50 Hz - Torque 25 Nm speed 17 r.p.m. - Supplied without adapters. - Quantity per standard package: - Weight: 2200 g
- Tubular actuator: 120 V - 60 Hz - Torque 1.3 Nm speed 65 r.p.m. - Supplied without adapters. - Quantity per standard package: - Weight: 1000 g
- Tubular actuator: 120 V - 60 Hz - Torque 4 Nm speed 36 r.p.m. - Supplied without adapters. - Quantity per standard package: - Weight: 800 g
- Tubular actuator: 120 V - 60 Hz - Torque 4 Nm speed 16 r.p.m. - Supplied without adapters. - Quantity per standard package: - Weight: 900 g
- Tubular actuator: 120 V - 60 Hz - Torque 9 Nm speed 16 r.p.m. - Supplied without adapters. - Quantity per standard package: - Weight: 1100 g

504 S2 RH

- Tubular actuator: 120 V - 60 Hz - Torque 4 Nm speed 38 r.p.m. - Supplied without adapters. - Quantity per standard package: - Weight: 1720 g

505 F2 RH

- Tubular actuator: 120 V - 60 Hz - Torque 5 Nm speed 64 r.p.m. - Supplied without adapters. - Quantity per standard package: - Weight: 1720 g

9147544

9132139
- For tube 50 x 2 mm MADOPRON

9132138

9701206

- For round tube 53 mm

9701213

9701207

Crown drive Tube adapter
- For round tube 51 x 1 mm HASSINGER - $up to 9 Nm

9701208

Wheel drive Tube adapter
- For round tube 47 mm HELIOSCREEN

9500322

9500354
- For round tube 48 mm GRIESSER

9500343

9701209
- For round tube 50 x 1,5 mmWAREMA

9701210

- For round tube 50 x 1,5 mm WAREMA
6 x 3 mm motor bracket for LS Motor bracket
- $Only with LYRA - + 3 screws
10 x 10 mm motor bracket for LS Motor bracket

- $up to 13 Nm

LO Motor bracket for LS Motor bracket
- Motor bracket suitable for fitting motors and roller blinds. - Provides 2 * M5 holes with 48 mm centres for fixing onto end plates

9137009

Motor bracket
Bracket and Plug-end for tube 40 x 1,5 mm

- $Only with LYRA

Drive Wheel (Soft clip) 9206089 Drive wheel
- For tube 50mm - No need for crown adapter - Quantity per standard package: - Weight:
Drive Wheel (Hard clip) 9206088 Drive wheel
- For tube 50mm - No need for crown adapter - Quantity per standard package: - Weight: 22 g
10 x 10 Motor bracket for LT 50 RH Motor bracket
- For motors up to 25 Nm - Can be used in combination with angle bracket 510660 - Quantity per standard package: - Weight: 35.6 g

US LO Plate 60 mm

- For direct mounting on side plate

9910011

US LO Plate
- Quantity per standard package: - Weight: 27.6 g

LO Plate 60 mm

9910012

LO Plate

Drive- Wheel for Siral tube and CTS 50 Nichibe Tube 9704080 Wheel
- For tube 52 - No need for crown adaptater - Quantity per standard package: - Weight: 25 g

9410665

Motor bracket for LS 40
- Used with motor bracket 10x10 ref.9147334 - Quantity per standard package: - Weight: 170 g

End plug for LS End Plug

- Quantity per standard package: - Weight: 62 g
Adjustable plug end for LS End Plug
- Pin 12, 40 - Quantity per standard package: - Weight: 200 g
Motor bracket for LS 40 / LT Bracket
- Quantity per standard package: - Weight: 170 g

- Quantity per standard package: 1 - Weight: 187 g - Dimensions: - Bus line control - Timer

1805031

Chronis IB
- Quantity per standard package: 1 - Weight: 162 g - Dimensions: - Sun sensor - 5 m white cables - Quantity per standard package: 1 - Weight: 780 g - Dimensions:

9101475

Soliris Sensor

- Wall radio transmitter

1810090
- Quantity per standard package: 1 - Weight: 78 g - Dimensions: - Radio transmitter - 1 channel

1810096

- Quantity per standard package: 1 - Weight: 88 gr - Dimensions: - Radio transmitter - 4 channel

1810018

- Quantity per standard package: 1 - Weight: 88 g - Dimensions: - RTS remote control transmitter - 1 channel for individual control - 433,42 Mhz frequency - Range: 200 m in free field - Quantity per standard package: 1 - Weight: - Dimensions: - RTS remote control transmitter - 1 channel for individual control - 433,42 Mhz frequency - Range: 200 m in free field - Quantity per standard package: 1 - weight: 88 g - Dimension: 120 x 45 x 17 - RTS remote control transmitter - 1 channel for individual control - 433,42 Mhz frequency - Limited range: 200 m in free field - Quantity per standard package: 1 - weight: 88 g - Dimension: 120 x 45 x 17 - RTS remote control transmitter - 1 channel for individual wind and sun control - 433,42 Mhz frequency - Limited range: 200 m in free field - Quantity per standard package: 1 - weight: 88 g - Dimension: 120 x 45 x 17 - RTS remote control transmitter - 1 channel for individual control - 433,42 Mhz frequency - Range: 200 m in free field - Quantity per standard package: 1 - Dimension: 120 x 45 x 17

1810024

Telis Soliris RTS

1810169

Telis 1 Silk RTS

1810170

Telis 4 Silk RTS

1810174

Telis Soliris Silk RTS

1810306

Telis 1 Patio RTS

- weight: 88 g

1810307

Telis 4 Patio RTS

- RTS remote control transmitter - 4 channels for individual / group control - 433,42 Mhz frequency - Limited range: 200 m in free field - Quantity per standard package: 1 - weight: 88 g - Dimension: 120 x 45 x 17 - RTS remote control transmitter - 1 channel for individual wind and sun control - 433,42 Mhz frequency - Limited range: 200 m in free field - Quantity per standard package: 1 - weight: 88 g - Dimension: 120 x 45 x 17 - RTS remote control transmitter - 1 channel for individual control - 433,42 Mhz frequency - Limited range: 200 m in free field - Quantity per standard package: 1 - weight: 88 g - Dimension: 120 x 45 x 17

1810308

Telis Soliris Patio RTS

1810025

Telis Soliris US Patio RTS

- Radio receiver

Centralis Indoor RTS
- Radio receiver - For venetians with tilt function

1810110

SL7070 Drape

1870011

IRT 103
- IR transmitter for IRS 100 & 200 - Supplied without batteries - 3 buttons for up, down, stop - Quantity per standard package: 1 - Weight: 45 g - Dimensions: 118 x 45 x 14 - 8 channel infrared transmitter for IRS 300 - Subgroup control 1-4 and 5-8 - Group control 1-8 - Supplied with batteries - Quantity per standard package: 1 - Weight: 101 g - Dimensions: 162x50x20 - Individual control - For bus line and AC motor infrared receiversl

1870010

IRT 803

9154186

IR Sensor
- Quantity per standard package: 1 - Weight: 67 g - Dimensions:

1822033

Bus line Infra-red Receiver AC motor Infra-red Receiver
- Control for Somfy BUS line by infra-red transmitter (IRT 103, IRT 803) or external input (individual push-button or Somfy Bus line). - 220-240 V - Colour: grey - Dimensions: 135 x 120 x 42 - Weight: 330 g - Control for Somfy BUS line by infra-red transmitter (IRT 103; IRT 803) or external input (individual push-button or Somfy Bus line). - 220-240 V - 3 different Drape functions for venetian blinds - Colour: grey - Dimensions: 135 x 120 x 42 - Weight: 330 g - Individual control with tilt function - Bus line connection for group control - 1 per motor - Quantity per standard package: 1 - Weight: 400 g - Dimensions: 112 x 52 x 106 - Group control unit for max. 4 motors

DMKI - DIVE 11R2