NOTE: Refer to page 67 of this catalog for limit setting instructions. 4

The SOMFY DC Motor Range

Technical Specifications
LV 25 Range - Single Shaft Drive
MOTOR TYPE NOMINAL TORQUE SPEED ELECTRICAL RATING WEIGHT THEORETICAL LIFTING CAPACITY*

in. lb.

LV 25-B44 LV 25-B64 3.52 5.28

0.4 0.6

24DC 24DC

Ampere

450mA 500mA

.322.322

.145.145
LW 25 Range - Double Shaft Drive
LW 25-B44 LW 25-B83 3.52 7.04

0.4 0.8

450mA 650mA

.432.432

.195.195

LT 28 Range

LT28 A LT28 AF LT28 B 6.16 6.16 6.16

.7.7.7

12VDC 12VDC 24VDC

750mA 750mA 380mA

.6.6.6

.27.27.27

8.8 8.8 8.8
* See chart on page 22 for Product Applications/ Lifting Specifications

The SOMFY AC Motor Range

Motor Names
It is easy to understand these names as they follow the logical order of increasing torque and have a letter indicating the application (speed).
Torque (Nm) Motor Diameter 4 for LSfor LTfor LT60 Speed R: Rolling Shutter = 14 rpm A: Awning = 20 rpm (LT50 range only) S: Screen = 36-38 rpm F: High Speed = 64 rpm Range-Voltage 120V Range 2 230V Range 1
Conversion Factor: 1 Nm = 8.8 in. lbs.

Radio Technology Somfy

* Important information which must be understood before using the following technical specifications.
SOMFY motors are not designed for continuous operation. They are equipped with a built-in thermal overload protector which limits their operation to intermittent use only. in accordance with Underwriter Laboratories, Inc. and Canadian Standards Association specifications. Maximum running time is approximately 5 minutes depending upon operating conditions. Although SOMFY motors are designed for indoor and outdoor use, they must be protected from direct weather elements such as: rain, sleet, etc. Theoretical Lifting Capacity does not take into account any systems losses and should be used only as a reference. For the definition of Theoretical Lifting Capacity please refer to page 13. The actual lifting capacity of the particular motor depends on other factors such as tube diameter used and its length, selection of motor accessories (brackets, end caps, etc.), and mounting method used. Please consult SOMFY Systems for assistance with determining the actual lifting capacity of SOMFY motors in your particular application.

OTHER LS40 RANGE MOTORS OTHER LS40 OR LT50 RANGE MOTORS OTHER LS40 OR LT50 RANGE MOTORS
kg. TYPE OF TUBE ROUND 2.0 (51) ROUND 2.5" (63.5) ROUND 3.0 (76) ROUND 3.5" (89) lb.

45 100

55 120

64 140

73 160

82 180

504S2 504S2 504S2 504S2
506S2 506S2 506S2 510S2 510S2

510S2 515S2 515S2 515S2

OTHER LT50 RANGE MOTORS OTHER LT50 RANGE MOTORS OTHER LT50 RANGE MOTORS

OTHER LT50 RANGE MOTORS

For Interior Window Coverings
PLEATED, CELLULAR AND ROMAN

Motor Type

Output Drive (Hexagonal Shaft)
Single Single Double Double
Maximum area for Pleated Shades Sq. Ft.
60 Sq. Ft. 90 Sq. Ft. 60 Sq. Ft. 120 Sq. Ft.
Maximum area for Cellular Shades Sq. Ft.
53 Sq. Ft. 75 Sq. Ft. 53 Sq. Ft. 105 Sq. Ft.

Roman Shades Lbs.

4.25 Lbs. 7.5 Lbs. 4.25 Lbs. 8.5 Lbs.
Maximum height with 1.4 mm cord
11.5 Ft. 11.5 Ft. 11.5 Ft. 11.5 Ft.

Speed (RPM)

LV 25-B44 LV 25-B64 LW 25-B44 LW 25-B83
Specifications based on motors used with (CTS). They are approximate and may vary depending on product application, fabric etc.

Output Drive

120 Sq. Ft. >120 Sq. Ft. >120 Sq. Ft.
105 Sq. Ft. >105 Sq. Ft. >105 Sq. Ft.

8.8 Lbs. 21 Lbs. 42 Lbs.

13 Ft. 18 Ft. 19.8 Ft.

LT28 LS40* LT50**

Tubular Tubular Tubular
* LS40 Based on use of 404S2 ** LT50 Based on use of 510S2

HORIZONTAL BLINDS

Maximum area for 25 mm Aluminum blinds ( Sq. Ft.)
22 Sq. Ft. 44 Sq. Ft. 22 Sq. Ft. 54 Sq. Ft.
Maximum area for 50 mm Wood blinds ( Sq. Ft.)

NA NA NA 27 Sq. Ft.

Maximum height with O 1.4 mm cord ( Ft.)
LV 25-B44 LV 25-B64 LV 25-B44 LV 25-B83
Specifications based on motors used with (CTS). They are approximate and may vary depending on product application.

75 Sq. Ft. 75 Sq. Ft.

75 Sq. Ft. 120 Sq. Ft.

13 Ft. 19.8 Ft.

LS40* LT50**

Tubular Tubular

Specifications based on motors used with (CTS). They are approximate and may vary depending on product application. * LS40 Based on use of 409R2 ** LT50 Based on use of 510R2
Special Application Motors

ILT Motor

The ILT motor features an on board microprocessor and uses a digital shaft encoder to track the position of the motor. Limits are set using the ILT switch itself, virtually eliminating the need to access the motor when adjusting the limits. A low voltage modular cable links the motor to the switch, and a separate 3-conductor (L-N-G) cable supplies power to the motor. On-board control and electronic limits are combined to provide these additional features: * Low voltage control from a switch, infrared transmitter, home automation or network controls * Individual or group control from a switch or IR sensor without additional components * One user defined intermediate stop from a switch or remote

LOAD BAR

STRAP MOTOR
NOTE: The SOMFY FTS System is a specialized system and should not be installed without proper training from a SOMFY technician.

POWER SOURCE 120V AC

SWITCH
For a quick reference guide to our installations, refer to page 26 and 27 of this catalog. The complete instructions are available on our website at www.somfysystems.com under the Technical Documentation section.
SLT and OREA RTS Motors SLT
The SLT Range is made exclusively for cassette awnings. What separates the SLT from a standard LT is the onboard control which detects when a cassette is almost closed and reduces the torque of the motor for the last few inches of travel. Then when the headrail meets the cassette, the on-board control shuts the motor off. The combination of digital control plus a reduced-torque closing provides the maximum protection against fabric stretch. For more information, turn to page 66.

OREA RTS

The new radio version of the SLT motor is the OREA RTS. This motor can be mounted on the left or right side of the cassette awning and is compatible with the RTS sensors. It features an integrated radio receiver with remote limit setting and a remote user programmable intermediate stop. 24
FTS Motor Selection Guide
This motor chart was created based on experimental results. The following tube diameters were used:
LT50 LT60 FABRIC TUBE O70 O78 STRAP TUBE O63 O63

WIDTH LENGTH/PROJECTION

13.1ft

16.4ft

19.6ft

22.9ft

26.2ft

29.5ft 32.8ft

3.2ft 1m 6.5ft 2m 9.8ft 3m 13.1ft 4m 16.4ft 5m 19.6ft 6m 22.9ft 7m 26.2ft 8m 29.5ft 9m 32.8ft 10m 36ft 11m 39.3ft 12m

10.7 ft2

21.5 ft2

32.2 ft2

43.0 ft2

53.8 ft2

64.5 ft2

75.3 ft2

86.1 ft2

96.8 ft2

107.6 ft2

129.1 ft2

150.7 ft2

172.2 ft2

193.7 ft2

215.2 ft2

FTS 25/20
96.8 ft2 129.1 ft2 129.1 ft2 172.2 ft2

161.4 ft2

226.0 ft2

258.3 ft2

290.6 ft2

322.9 ft2

120VAC Supply Neutral White (both motors) Winding Tension STRAP MOTOR Brake (gray) Winding Tension FABRIC MOTOR Brake (gray)

Switch and Security

Common Direction 1 - Fabric Unwinding Direction 2 - Fabric Winding Lockout
Jumper needed if lockout not used.

Jumper or Alarm Contact

50-60 Hz Pin Selector
Asymetric Tension Adjustment

Final Tension Adjustment

Dynamic Tension Adjustment

Brake Release Button

DC Motor Mechanical Accessories
DC LT28 BRACKETS AND END CAPS

Dimensions (mm)

Cat. Number

6180353

Description
Angle Brackets w/Teflon Bushings - 4 screws and anchors included - O 4 mm idler bushing included

6180354

Angle Brackets w/Plastic Caps - Compatible with 6090315 idler end cap - Pin O 4 mm

6180356

Standard Brackets

6090315

End Cap For Tube 28 x 0.7 mm, 29 x 1.15 mm and 29 x 2.0 mm - Pin O 4 mm

O 39 O 2.4

6061298
Flush Mount Bracket for LT28A and LT28B Motor
Headrail Adaptors for LV and LW Motors

6050009

Headrail Adaptor for 25 x 25 mm/Celebrity/Best Buy

6050008

Headrail Adaptor for Fbr. 25 x 25 mm

6050007

Headrail Adaptor for SoftLine

6050006

Headrail Adaptor for MidiMatic

6050005

Headrail Adaptor for Classic Supreme

6050004

Headrail Adaptor for Verosol Europe/Mexico

6050010

Headrail Adaptor for VersaRail/Easy Up/Activator/EasyGlide

6050650

Headrail Adaptor for EasyRise (New Version/Old Version)

6050600

Headrail Adaptor for GutterRail/Low Profile 2 Headrail

6050602

Headrail Adaptor for SureClose Headrail

6050013

Headrail Adaptor for LightLines

6050003

Shaft Adaptor for 5 mm Hexagonal

6051003

6180497

CTS 25 (Kit) Short Cones for VersaRail Headrail (5 mm Hex Shaft)

6180498

CTS 25 (Kit) Short Cones for VersaRail Headrail (6 mm Hex Shaft)
LS40 Mechanical Accessories

6061308

LS40 to LT50 Adaptor Kit - Allows the use of LT50 crowns and drives with LS40 motors - Black composite - Maximum motor torque - 13 Nm - Maximum system load - 56 Kg (123 Lbs.)

6070418

29 O 38
LS40 "LO" Bracket with a Square Stud - Motor mounting screws included - 10 mm square stud - Zinc plated steel - Maximum motor torque - 13 Nm - Maximum system load - See note below

6070521

48 O 58
LS40 and LT50 RH LO" Bracket with Round Hole - Two motor mounting screws included - Zinc plated steel - Maximum motor torque - 20 Nm - 2 holes for 1/4-20 screws on 48 mm diameter - Maximum system load - 70Kg (154 Lbs.) - Replaces SOMFY Cat. No. 6070419 LS40 Motor Bracket - Compatible with RolleaseTM Bracket - Stainless steel - Maximum motor torque - 4 Nm - Maximum system load - See note below

10.4 O 38

6070427

6070429

LS40 to LT50 Mounting Conversion Bracket - Black composite - Allows LS40 motors to be used with LT motor brackets - Maximum motor torque - 9Nm - 2 screws included - Maximum system load - 56 Kg. (123 Lbs.)

6090307

40 mm Diameter Adjustable End Cap - 12 mm dia. shaft (Zinc plated steel) - Cast aluminum with set screw.set screw must use lock-tight to prevent screw from vibrating free. - Kit containing (6090310, 6090195). These parts are available separately. - Maximum system load - See note below
Note: Maximum system load will vary depending on application. SOMFY recommends testing of component in actual application to determine its suitability.

6090185

40 x 0.6 mm Octagonal Tube End Cap - 8 mm dia. shaft - White composite - Maximum system load - See note below 40 x 1.1 mm Octagonal Tube End Cap - Same as above but modified to fit 40 x 1.1 mm tube

6090186

6080040
LS40 Idler Bracket (for 8 mm shaft) - Decorative white composite - Maximum motor torque - 4Nm (removable parts must be screwed together, see enclosed instructions). - Maximum system load - 17 Kg. (38 Lbs.)(must be screwed together) - Compatible with motor bracket Cat. #6070040

O 20.5

6070082

6070138

"U" Shape LS Style Motor Bracket for 10 mm Square Stud - Maximum motor torque - 25 Nm - Zinc-plated steel - Maximum system load - See note below - Replaces SOMFY Cat. No. 6070137

6070182

Heavy Duty Angle Plate - For ceiling and wall installation in combination with Cat. No. 6070503 - Black oxide finish - Compatible with brackets 6070503,6080026 and 6080116 - Maximum motor torque - 100 Nm - Maximum system load - See note below LT50 Round Anti-Vibration Motor Bracket - Zinc plated steel with a 10 mm molded square stud insert surrounded by rubber - Compatible with matching idler end Cat. #6080206 - Can be mounted on 6070526 - Maximum motor torque - 20Nm - Can reduce sound levels by 4-5 dB - Maximum system load - See note below

6070238

10 mm Square

6070256

Motor Bracket LT60 FTS - Zinc plated steel, gauge 3 (0.24 in.) - Recommended for use with LT FTS 60 (Fabric Tension System) - Maximum motor torque - 100 Nm - Includes universal bracket with spring ring that must be used - Maximum system load - 200 kg. (441 Lbs.) - Spring must be replaced with a locking spring ring 4350027 to obtain full torque and load capability.

6070284

LT50 Angle Plate with Elongated Holes Allowing Adjustment - Zinc plated steel - Compatible with idler end bearing support Cat. No. 9080239 and intermediate bearing support Cat. No. 6050438 - Maximum motor torque - 50 Nm - Maximum system load - 69 Kg. (152 Lbs.) - Replaces SOMFY Cat. No. 6070283

6070446

LT50/60 Motor Bracket with 1/2" Conduit Connector - Four mounting holes provided - Lateral space requirement for installation: 28 mm - Zinc plated steel - Must be used with either spring ring Cat. No. 4350026, or locking spring ring Cat. No. 4350027 (not included) - Maximum motor torque - 85 Nm or 100 Nm when locking spring ring Cat. #4350027 is used.

6070499

Universal Bracket with Spring Ring - Assembled to accept Inch Series threaded screws 1/4 - 20, 5/16 - 18 (nuts molded into bracket) Universal Bracket with Spring Ring - Zamak Material - 2 holes for M6 hex or 1/4 - 20 flat head screw on 48 mm diameter - 2 holes for M8 hex screw on 60 mm diameter - 2 countersunk holes for M8 screw on 60 mm diameter - Lateral space requirement for installation: 27 mm - Maximum motor torque - 85 Nm or 100 Nm when used with locking spring ring Cat. No. 4350027, and 5/16 - 18 or M8 bolts without molded nuts - Maximum system load - 200 Kg. (441 Lbs.) when used with locking spring ring Cat. #4350027 With M8 and M6 nuts molded in bracket - Same as above - Maximum system load 200 Kg. (441 Lbs.)

6070516

6070517

2 x M8

"LO" LT50 Motor Bracket - Comes with two 5 mm motor mounting screws - Maximum motor torque 50 Nm - Zinc plated steel - Maximum system load - See note below

6070518

Adjustable Motor Bracket with Spring Ring - Zinc-plated steel - Horizontally and Vertically adjustable - Lateral space requirement for installation: 27 mm - Maximum motor torque 50 Nm - Maximum system load - See note below

dia. 11

6070519

O 4.2 84

LT50 HA Motor Bracket - Allows flush mounting of the motor head against the mounting surface - Zinc plated steel - Maximum motor torque - 50 Nm - Maximum system load - See note below

6070522

LT RH Motor Bracket - Pin hole is vertical - Zinc plated steel - 10 mm square stud - Maximum motor torque - 25 Nm - Mounting Screws Cat. No 4000555 included - Maximum system load - 70 Kg. (154 Lbs.) Same as above except pin hole is horizontal

6070523

6070524
LT60 Retrofit Bracket with Spring Ring - Zinc plated steel - Maximum motor torque - 80 Nm - Allows retrofitting new LT60 motor into old 600s brackets - Maximum system load - See note below

6070525

LT Motor Bracket with a Square 16 x 16 mm Stud - Zinc plated steel - Maximum motor torque - 80 Nm - Required spring ring Cat. No. 4350026 not included - Maximum system load - See note below
Dimensions (mm) Cat. Number Description

6070526

LT50 Angle Bracket - For ceiling and wall installation - Zinc plated steel - Horizontally and vertically adjustable - Maximum motor torque - 50Nm - Maximum system load - See note below - Replaces SOMFY Cat. No. 6070193

2- O 5.3

6070188
CTS50 Motor Mounting Bracket (Cord Take-Up System) - Zinc plated steel - Attaches directly to LT50 motor head (48 mm on center) - Adaptable for Nichibei headrail (70 x 70) - Maximum motor torque - 10Nm - Maximum system load - See note below

Idler Brackets

6080189
CTS50 Motor Idler Bracket (Cord Take-Up System) - Zinc plated - 10 mm square shaft with ball bearings - Adaptable for Nichibei headrail(70 x 70) - Maximum motor torque - 10Nm - Maximum system load - See note below LT Idler End Bracket (inside diameter 10 mm) - Zinc plated steel - 10 mm ID Nylon ball bearing - Compatible with motor bracket 6070082 and 6070513 - Maximum motor torque - 50 Nm - Maximum system load 130 Kg. (287 Lbs.) - Replaces Somfy Cat. No. 6080048 Same as above but with a 12 mm ID Nylon Ball Bearing - Replaces Somfy Cat. No. 6080228 Idler Bracket 10 mm Ball Bearing and Holder Kit Nylon Ball Bearing with 10 mm ID Nylon Ball Bearing with 12 mm ID Ball Bearing Holder - Used with Cat. No. 6080138 or 6080241 ball bearings - Zinc plated steel - Maximum motor torque - 50 Nm - Maximum system load - up to 130 Kg. (287 Lbs.) Heavy Duty Idler Bracket - Used with end cap having stationary 16 mm diameter shaft (example Cat. No. 6090256) - Cotter pin holding end cap's shaft included - Zinc plated steel - Maximum motor torque - 100 Nm - Maximum system load - See note below LT50 Round Anti-Vibration Idler Bracket - Zinc plated steel with a 10 mm round insert surrounded by rubber - Compatible with matching motor bracket Cat. #6070238 - Can be mounted on 6070526 - Maximum motor torque - 20Nm - Can reduce sound levels by 4-5 dB - maximum system load - See note below LT50 Idler Bracket with 14 mm ID Bearing - Zinc plated steel - Adjustable bearing location - Maximum motor torque - 50 Nm - Maximum system load - See note below - Replaces SOMFY Cat. No. 6080217

6250701

CMO ME Square Awning Motor Bracket - U.S. thread 1/4 - 20, 5/16 - 18 threads - Delivered with two motor mounting screws (3/16 Socket Head) - Black finished aluminum alloy - Maximum motor torque - 100 Nm (must be used with 5/16 - 18 bolts at maximum torque) - Maximum system load - See note below

6250702

CMO Motor Bracket - Converts a CMO motor head to be compatible with standard LT brackets - Allows the motor to be rotated in 60o increments - Delivered with two motor mounting screws - Black composite - Maximum motor torque - 80 Nm - Maximum system load - See note below

6250713

CMO Awning Eye with 2.36" (60 mm) Long 7 mm Hex Shaft CMO Awning Eye with 6.5" (165 mm) Long 7 mm Hex Shaft CMO Awning Eye with 4" (100 mm) Long 7 mm Hex Shaft

6250712

LT CMO Awning Eye Compatible with Geiger Crank Handles - Length of the shaft is (100 mm) 4" - Stainless steel pin for eyepiece mounting to 7 mm Hex shaft - Stainless steel stop washer & socket head screw (also sold separately) - Zinc plated steel shaft - Stainless steel lock washer - Stainless steel M4 socket head screw CMO Extension Shafts - 7 mm Hex, 8.66" (220 mm) long - Zinc plated steel - 7 mm Hex, 13" (330 mm) long - Zinc plated steel Connecting Sleeves - 7 mm Hex to diameter 11.3 mm - Zinc plated steel - 7 mm Hex to 8 mm Square - Zinc plated steel - 7 mm Hex to 7 mm Hex - Zinc plated steel CMO Extension Shaft with Universal Joint - Shaft 7 mm Hex, 12.4" (315 mm) long - zinc plated steel - Output of the universal joint is a 12 mm diameter hole - Universal joint - White powder coated steel - Color: white fixing plate - 60o outlet

6250715

6250716

6250717

6250718 6250719

6250720

6250721
CMO Extension Shaft with Awning Eye and Plate - Shaft 7 mm Hex, 10.25" (260 mm) long- Zinc plated steel - Color: white fixing plate with black awning eye - 60o outlet

6250723

LT CMO 70 Degree, 4 Hole Plate SS Crank Handle Universal Joint - Compatible with 14 mm diameter bell type connectors - Material: Stainless steel and nickel plated zinc casting plate - 7 mm hex shaft: Steel, zinc plated

6250724

LT CMO 90 Degree, 2 Hole Plate SS Crank Handle Universal Joint - Material: Stainless steel and nickel plated zinc casting plate

6250725

LT CMO 90 Degree, 4 Hole Plate SS Crank Handle Universal Joint

LT Range

SOFT CLIP (Removable)
Installation of the drive wheel to the motor shaft: Push the drive into the motor shaft until you hear a "click". Two clips lock the drive wheel into the motor shaft. There are two types of LT drive wheels: Removable or "Soft Clip" type, and fixed or "Hard Clip" type.

Motor Shaft

Drive Wheel Clips

Motor Shaft in Place

The "Soft Clip" drives are available only for round tubes in 2", 2.5" and 2.75" diameters. The drive wheel can be removed by physically pulling it off the motor shaft. For the ease of identification all "Soft Clip" drives are brown. The "Hard Clip" drives can only be removed from the shaft by pressing the two clips inward at the same time. The motor must be out of the tube in order to have access to the clips. These drives are black. Installation in round tubes: The drive must be riveted to the tube after the motor is inserted. See page 62 for required fastener size and quantity. Installation in profiled tubes: The drive doesn't need to be riveted to the tube because it is already in a positive lock position within the profiled tube.

Open Grooves

HARD CLIP (Fixed)
Motor Shaft Locked in Place

Closed Grooves

LS40, LT50/60, LT50 RH
Determining the Tube Length (B):
Clear dimension (A) Space requirement for motor bracket (C) Space requirement for idler bracket (D)

C B A D

= Tube length (B) The dimensions for the lateral space requirement for the motor brackets and idler brackets depends on the bracket design in each instance. They also include the space requirements for the motor head which are listed on pages 10-12.

Installation

- Attach motor brackets - Provide opening for the motor cables - Install the motor in the tube. Only push the motor into place. Never hit into place with a hammer! Profiled Tubes Push on the motor crown and drive wheel (which fit the prefinished tube) and slide motor inside the tube. Round Tubes Notch the tube on the motor side for the basic motor crown and push on the drive wheel. Now slide the motor into the tube in such a way that the raised key of the crown comes to rest in the cut notch. A Notch: LS40 Length = 8.5 mm LTmm LTmm

Raised Key

B Width = 6 mm 4 mm 8 mm

Motor on Left

Motor on Right

Position 2

Adjustment of Upper and Lower Positions for the LS40 Motor

Stop Position 2

- Connect the motor tester cable (Cat. No. 6020086) to the motor cable, match the wire colors and connect to power. - Identify the UP recessed limit screw by finding the arrow on the motor head which points in the direction that retracts (rolls up) the system. - Turn the power on to ensure that the switch is operating properly (UP-raises, DOWN-lowers). If not, turn the power off and simply reverse the black and red motor leads. - Flip the tester cable switch in the UP direction. If the system stops before its UP limit, turn the UP screw to "+" until necessary. If the system does not stop at its UP limit, flip the tester cable switch off and turn the UP screw to "-". Repeat this until correct setting is achieved. NOTE: 7 Turns of Hex Screws equals 1 turn of roller tube. - Flip the tester cable switch in DOWN direction. If the system stops before its DOWN limit, turn the DOWN limit screw to "+". If not, flip the tester cable switch off and turn the DOWN limit screw to "-". Repeat this until correct setting is achieved. NOTE: Recessed thumbscrews can accomodate a flat head screwdriver, SOMFYs Allen wrench or Flexible limit switch adjuster.
LT50/60 CMO and LT50 RTS CMO
Programming and Limit Setting Instructions
For initial programming, provide power only to the motor being programmed. For awning installations, an awning hood is strongly recommended and a drip loop should be formed to prevent water from entering the head of the motor as shown in Fig. (1). Fig. (1) Follow the steps below to program the motor and set the limits.
1) Provide power to the motor.
Remove cap as shown in Fig. (2) and depress both limit switch buttons until they lock in the down position. To assign the transmitter to communicate with the motor, push the UP and DOWN buttons on the transmitter simultaneously until the motor jogs briefly up and down then release. See Fig. (3).

120 VAC

NEUTRAL

DRIP LOOP

GROUND

Fig. (2)

Fig. (3)

Fig. (4)

UP STOP DOWN
2) Check the direction of operation.
The DOWN button should correspond with the down direction of the end product (for awnings DOWN extends the awning). If the direction is wrong, press the STOP button on the transmitter as shown in Fig. (4) until the motor jogs. Check the direction again to make sure it is correct.
3) Setting the UP and DOWN limits
Press the UP button of the transmitter until the end product reaches the required UP position, then stop it. Unlock the UP limit switch on the motor head by pressing and releasing it. The UP limit is now set. Repeat the above operation to set the DOWN limit.

Transmitter previously recorded

New Transmitter

Repeat this procedure for each additional transmitter/channel you wish to add or delete. It is not possible to delete the transmitter/channel used to enter the programming state. 69
3) Resetting the motor's memory and recording a new
transmitter when the only transmitter is lost.

! NEW TRANSMITTER

**A. Perform a double power cut in the following sequence:
1. Power-off - 2 sec. minimum 2. Power-on - 5 to 15 seconds 3. Power-off - 2 sec. minimum 4. Power-on The end product moves for 5 seconds in one direction, to indicate that the double power cut has been recorded.The motor is in a PROGRAMMING STATE for 2 minutes.

>5 sec.

5 seconds
B. Recording a New Transmitter
Press the programming button of the NEW RTS transmitter For 1 second max. Release it after the end-product jogs briefly UP/DOWN indicating that the transmitter has erased all previous transmitters and recorded the NEW one.
**RESETTING MOTORS BACK TO USER MODE
WARNING: This type of power cut affects all
the ALTUS RTS motors on the same power line. To avoid resetting of non-concerned motors, press briefly any button of their assigned transmitter/channel (UP STOP or DOWN). , , The non-concerned motors will return to USER MODE.
C. Restoring Factory mode with a New Transmitter
Press and HOLD the programming button of the NEW RTS transmitter for more than 7 seconds. The end-product will jog briefly UP/DOWN twice. Once after 1 second and again after 7 seconds. This indicates the ALTUS/OREA RTS motor has been completely cleared.
4) Back to the factory configuration (to completely reset the ALTUS RTS motor memory)
**A.Perform a power cut in the following sequence:
1. Power-off - 2 sec. minimum 2. Power-on - 5 to 15 seconds 3. Power-off - 2 sec. minimum 4. Power-on The end product moves for 5 seconds in one direction, to indicate that the double power cut has been recorded. The motor is in PROGRAMMING STATE for 2 minutes.
! PREVIOUSLY RECORDED TRANSMITTER

>5 sec. 5 seconds

B. Restoring Factory Mode with a Previously Recorded Transmitter
Operator Wiring Instructions

LT50/60

Incorrect
DECORATOR PADDLE/ TOGGLE SWITCH

WARNING:

Do not wire two or more LT operators to one single pole switch. This will cause the motors to malfunction.

GROUND CONNECTED TO BOX

LT MOTOR WIRING COLOR CODE
120V AC CODE WHITE PUSH-BUTTON YELLOW PUSH-BUTTON (C) COMMON (G) GROUND BLACK RED WHITE GREEN
Note: Only RTS and ILT motors can be wired in parallel.
LT50 ALTUS RTS AND LT50 RTS CMO MOTOR WIRING COLOR CODE
120V AC CODE (H) HOT (N) NEUTRAL (G) GROUND BLACK WHITE GREEN
Operator Wiring Considerations

670013 100405A 9703956 9910004

9001264 9203887

9000980

9163325 9163334

Cat. No. 6061126 6061216

2005 No. 9500687 9138028

Description LS 40 Intermediate Bracket Fabric Clip for 40 mm Tube Fabric Fastener for 2" (50 mm) O.D. Tube Fabric Fastener for 2.5" (63 mm) O.D. Tube 45 x 51mm Extruded Aluminum White Headrail (max. 20 Ft.) CTS 50 Headrail Mounting Brackets CTS 50 Headrail Finished Side Caps Headrail for CTS 50 Headrail Cover for CTS 50 Heavy Duty LT Intermediate Support Bracket Light Duty LT50 Intermediate Support Bracket for a 2" Tube Headrail Side Caps 63 x 1.5 mm (approx. 2.5") Tube Cord Take-up Reel 50 x 1.5 mm (approx. 2") Tube Cord Take-up Reel LT50 Intermediate Bracket with 16 mm ID Bearing LT50 Adjustable Intermediate Support Bracket for a 2" Tube LT50 Adjustable Intermediate Support Bracket for a 2.5" Tube Stop Collar Ring for 5 mm Hex Shaft Stop Collar Ring for 6 mm Hex Shaft Ladder Braid Crimps 5 mm Hex Shaft for CTS (16 Ft. Maximum Length) 6 mm Hex Shaft for CTS (7 Ft. Sections) 2 Slat Clips for Wood Blinds (White) 2 Slat Clips for Wood Blinds (Ivory) 2 Slat Clips for Wood Blinds (Brown) Decorative Tape Adaptors for 1 Cotton Tape Decorative Tape Adaptors for 1.5 Cotton Tape Idler End Bearing Support for 16 mm Dia. Shaft 6 mm Hex Shaft for CTS (5 Ft. Sections) 2 Tube Take-up Reel 40 mm Tube Take-up Reel 40 mm Octagonal Tube LT Intermediate Bracket for 2 Tube Headrail Adaptor for GutterRail/Low Profile 2 Headrail Headrail Adaptor for SureClose Headrail Headrail Adaptor for EasyRise (New Version) Wall Mount Brackets for RDS/RTS Control Long Shaft Adaptor for 6 mm Hexagonal Long Shaft Adaptor for 5 mm Hexagonal 2.75 Round LT50 Crown 2.75 Round LT60 Crown 70 mm Octagonal LT60 Crown DS 70 LT Drive (1.2 -1.5 mm wall thickness) P72 LT60 Crown DS 70 LT50 Crown DS 78 LT60 Crown 3.5 Round LT60 Crown 3.5 Round LT50 Crown DS 74 LT50 Crown DS 78 LT50 Crown I65 LT50 Crown DS 78 / R LT60 Crown 4.0 Round LT60 Crown 4.0 Round LT60 Set I85 LT60 Crown I85 LT60 Set DS 78 / D LT60 Crown DS 85 LT60 Crown

Page 53 53

9002541

9162258 9162257

9146011

9707639 9705776

Cat. No. 6061401 6061402

2005 No. 9147545 9147327

Description DS 85 LT50 Crown Ls40 Drive for (40 x 1.5 mm) Tube LS40 Crown for (40 x 1.5 mm) Tube LS40 Drive for (40 x 0.8 mm) Octagonal Tube LS40 Crown for (40 x 0.8 mm) Octagonal Tube LSmm Round Set LSmm Octagonal Set Flush Mount Bracket for LT28A and LT28B Motors ABS Wheel-Left Rotation ABS Wheel-Right Rotation CMO ABS Wheel-Left Rotation CMO ABS Wheel-Right Rotation LS40 to LT50 Adaptor Kit LS40 Drive for (40 x 1.0 mm) Tube LS40 Crown for (40 x 1.0 mm) Tube 2.5 Round LT Drive (63 mm x 1.5 mm) - Soft Clip 2.5 Round LT Drive (63 mm x 1.5 mm) - Hard Clip 2.75 Round LT Drive (70 mm x 1.5 mm) - Hard Clip 3.5 Round LT Drive (89 mm x 1mm) 3.5" Round LT Drive (89 mm x 2 mm) 4.0 Round LT Drive (102 mm x 2 mm) 70 mm Octagonal LT Drive P72 LT Drive DS 78/R LT Drive DS 78 LT Drive DS 78/D LT Drive DS 85 LT Drive I85 LT Drive 70 mm Octagonal, Aluminum LT50/60 Drive Wheel Kit 2 Round LT50 Drive (50 mm x 1.5 mm) - Soft Clip 2 Round LT50 Drive (50 mm x 1.5 mm) - Hard Clip 2.5 Round LT50 Set - Hard Clip 2.75 Round LT50 Set 2.75 Round LT Drive (70 mm x 1.5 mm) - Soft Clip 60 mm Octagonal LT50 Set 60 mm Octagonal LT Drive 70 mm Octagonal LT50 Set P72 LT50 Set 3.5 Round LT50 Set DS 70 LT50 Set DS 70 LT Drive (0.8 -1 mm wall thickness) DS 74 LT50 Set DS 74 LT Drive DS 78 LT50 Set I65 LT50 Drive I65 LT50 Set SM 65 LT50 Crown - 3 grooves SM 65 LT Drive AMA71 LT50 Drive AMA71 LT50 Crown LT60 Crown (78 mm Dia.) LT60 Drive (78 mm Dia.) 2 LT Drive for CTS 50 Tube 50 mm Octagonal LT50 Crown 50 mm Octagonal LT50 Drive 2.75 Round LT60 Set 70 mm Octagonal LT60 Set 3.5 Round LT60 Set

Page 52 54

9206088

9206026 9751001

9705344

Cat. No. 6080256 6080257

2005 No. 9707026 9707025
Description 2.5 Round LT50 Crown 60 mm Octagonal LT50 Crown LT50 Motor Angle Bracket Molded LT28 Motor/Idler Brackets LS40 Radial Square Motor Bracket Universal LT50 Motor Bracket (LS Style) "U" Shape LS Style Motor Bracket Heavy Duty Angle Plate CTS 50 Motor Bracket LT50 Round Anti-Vibration Motor Bracket Motor Bracket LT60 FTS LT50 Angle Plate with Elongated Holes Allowing Adjustment LS40 "Lo" Bracket with a Square Stud LS40 Motor Bracket LS40 to LT50 Motor Mounting Conversion Bracket LT50/60 Motor Bracket with 1/2" Conduit Connector Universal Bracket with Spring Ring Weld-on Bracket Without Spring Ring Universal Bracket with Spring Ring -Zamak Material Universal Bracket With Spring Ring and Metric Molded Nuts Heavy Duty Angle Plate with Universal Motor Bracket Heavy Duty Angle Plate Motor Bracket With Spring Ring (120 mm x 120 mm) LT50 Adjustable Universal Motor Bracket Motor Bracket With Spring Ring (100 mm x 100 mm) LT50/60 Radial Motor Bracket LT50 Universal Motor Bracket Retrofit Brackets Pin Hole Vertical Retrofit Brackets Pin Hole Horizontal Lo LT50 Motor Bracket Adjustable Motor Bracket with Spring Ring LT50 HA Motor Bracket LS40 and LT50 RH LO Bracket with Round Hole LT RH Motor Bracket with Vertical Pin Hole LT RH Motor Bracket with Horizontal Pin Hole LT60 Retrofit Bracket with Spring Ring LT Motor Bracket with a Square 16 x 16 mm Stud LT50 Angle Bracket LT50 Anti-Vibration Motor Bracket LT50 Anti-Vibration Motor Bracket Headrail Mounting Brackets LS40 Idler Bracket for 8 mm Shaft Idler Bracket 10 mm Ball Bearing and Holder Kit Heavy Duty Idler Bracket Nylon Ball Bearing with 10 mm ID Ball Bearing Holder CTS 50 Headrail Mounting Bracket CTS 50 Motor Idler Bracket LT50 Round Anti-Vibration Motor Bracket LT50 Idler Bracket with 14 mm ID Bearing Idler End Bearing Support for 14 mm dia. shaft (no hardware) Nylon Ball Bearing with 12 mm ID Idler End Nylon 12 mm Ball Bearing with Holder LS40 Motor/Idler Bracket for 2 x 2 1/4 GutterRail Headrail LT50 Idler Bracket with Nylon Bearing (for 10 mm Shaft) LT50 Idler Bracket with Nylon Bearing (for 12 mm Shaft) Heavy Duty Idler Bracket with Idler End Cap Holder Idler End Cap Holder

Somfy Altus Motor Wiring Diagram

LT50 ALTUS RTS

GROUND

NEUTRAL

LT50 RTS CMO
Note: Only RTS and ILT motors can be wired in parallel.
LT50 ALTUS RTS AND LT50 RTS CMO MOTOR WIRING COLOR CODE 120V AC BLACK WHITE GREEN CODE (H) HOT (N) NEUTRAL (G) GROUND
1600 E. St. Gertrude Pl. Santa Ana, CA 92705 800-332-2866 714-708-1399, Fax License # 700678

Santa Ana

8120 Miramar Rd. San Diego, CA 92126 858-621-6300 858-621-6333, Fax License # 700678

San Diego