Awnings

MOTORS & ACCESSORIES
Motor Selection Chart.. 2-3 Altus 50 RTS & Altus 60 RTS. 4-5 Orea 50 RTS & Orea 60 RTS..6-7 Orea 50 WT & Orea 60 WT.. 8-9 LT50 & LT60.. 10-11 LT50 CSI & LT60 CSI... 12-13 LT50 CSI RTS..14-15 Phoenix...16-17 Adaptors - 50mm, 60mm Motors. 18-20 Motor Brackets - 50, 60mm CSI Motors.21-22 Bearings - 50, 60mm Motors. 23 Plug End Brackets - 50, 60mm Motors. 24 CSI Accessories - 50, 60mm CSI Motors.. 25 Phoenix Accessories.. 26 Cables.. 27-28 Test Leads & Limit Adjusters.. 29
FOLDING ARM AWNING MOTOR SELECTION CHART
The following chart is a guide only. Refer to the hardware manufacturer for more details.
HOW TO USE THIS SELECTION CHART
Refer to the chart that corresponds to the projection required. Select the tube size from the left hand column. Select the motor suitable by matching the arms & tube size together. A safety factor has already been incorporated. Installation length shown in metres.

Projection up to 1.5m

Number of Arms --> Installation length (m) -->

Tube Diameter (mm)

63/70 78

Projection up to 2m

Projection up to 3m

Projection up to 5m

Torque --> 50 Motor Designation
LT 50 Gemini Altus 50 25Nm Orea 50 25Nm Gemini CSI
LT 50 Helios Altus 50 30Nm Orea WT 30Nm Helios CSI RTS

Orea 50 35Nm

LT 50 Mariner Altus 50 40Nm Orea WT 40Nm Orea 50 40Nm Mariner CSI Mariner CSI RTS
LT 50 Vectran Altus 50 50Nm Orea 50 50Nm Orea WT 50Nm Vectran CSI RTS
Torque --> 60 Motor Designation
LT 60 Vega Altus 60 60Nm Vega CSI

LT 60 Sirius Sirius CSI

100 Nm
LT 60 Titan Altus 60 100Nm Orea 60 100Nm Orea WT 100Nm Titan CSI

120 Nm

copyright SOMFY Pty. Limited
LT 60 Taurus Altus 60 120Nm Taurus CSI

[ Awnings: 2 ]

DROP ARM AWNING MOTOR SELECTION CHART
Refer to the chart that corresponds to the number of arms to be used in the system. Select the drop from the left hand column. Select the motor suitable by matching the width & drop together. A safety factor has already been incorporated. Installation sizes shown in metres.

2 Arms

Total Width (metres) --> 1.4 1.2 1.5 1.8 2.1

Drop - (metres)

4 Arms
LT 50 Meteor Altus 50 20Nm Meteor CSI RTS
LT 50 Gemini Altus 50 25Nm Gemini CSI
LT 50 Helios Altus 50 30Nm Helios CSI RTS
LT 50 Mariner Altus 50 40Nm Mariner CSI Mariner CSI RTS

[ Awnings: 3 ]

ALTUS 50 RTS ALTUS 60 RTS
MAIN CHARACTERISTICS & FEATURES
230V / 50Hz tubular motor. The Altus RTS (Radio Technology Somfy) is suitable for a wide range of awning applications. Available in torques from 25Nm (50mm) to 120Nm (60mm) and coupled with its 48mm or 60mm (respectively) design, it is adapted for 50 tubes and above. A built-in radio receiver with Somfys rolling code for RTS control, the Altus RTS allows the user to operate almost any application with the convenience of a remote control. Remote set limits. Turning capacity limited only by thermal time. Suitable for tubes: 50 to 85. Memory Capacity: 12 channels / transmitters, plus 3 sensors. Programmable my position. Requires the use of a crown and wheel for tube adaptation. Horizontal mount only. Intermittent Usage.
ALTUS ALTUS ALTUS ALTUS RTS RTS RTS RTS 25/17 30/17 40/17 50/12
Torque (Nm) Torque (Nm) Torque (Nm) Torque (Nm) Speed (RPM) Speed (RPM) Speed (RPM) Speed (RPM) Ref. Ref. Ref. Ref. 1049447 1051304
ALTUS ALTUS ALTUS ALTUS ALTUS RTS RTS RTS RTS RTS 55/17 70/17 85/17 100/12 120/12
Torque (Nm) Torque (Nm) Torque (Nm) Torque (Nm) Torque (Nm) 120 Speed (RPM) Speed (RPM) Speed (RPM) Speed (RPM) Speed (RPM) 12 Ref. Ref. Ref. Ref. Ref. 1167039

[ Awnings: 4 ]

TECHNICAL CHARACTERISTICS
Blue = Neutral Brown = Active Yellow /Green = Earth

17.15 min 20

17 min 23

ALTUS RTS 100/12

ALTUS RTS 120/12

ALTUS RTS 40/17

ALTUS RTS 50/12

ALTUS RTS 85/17

ALTUS RTS 30/17

ALTUS RTS 70/17

ALTUS RTS 55/17

ALTUS RTS 25/17

L1 (mm) L2 riveting distance (mm) Torque (Nm) Speed (rpm) Rated Voltage (V) Rated Power consumption (W) Rated Current (A) Running time before thermal cut off (min) Thermal cut off temp (C) Average running noise (dbA) Minimum tube diameter Motor weight (kg) Cable length (M) Number of cores in cable Cross section of cable (mm) Index Protection Approval

0.50 x 1.5 2.3 0.75 IP44

1.50 x 1.5 2.3 0.75 IP44

1.63 x 1.5 4.3 0.75 IP44

1.140* x 1.5 4.3 0.75 IP44
1.140* x 1.5 5.3 0.75 IP44
NOTE Information about the noise is according to Somfy measures and is for information only. Taken as the worst value in load, for the up direction during the rst 10 seconds of travel.
Normal functioning temperature: -10C to +40C
* Thermal protection will not automatically reset. Power off then on the motor to reset.

[ Awnings: 5 ]

OREA 50 RTS OREA 60 RTS
230V / 50Hz tubular motor. The Orea 50 / 60 RTS is suitable for awning application types that require the use of a sealed cassette box. Available in torques from 25Nm (Orea 50) to 100Nm (Orea 60), coupled with its flexible 48mm (Orea 50) or 60mm (Orea 60) design, it is adapted for 50mm tubes and above. A built-in radio receiver with Somfys rolling code and over torque upper limit functionality are integrated to provide a tightly sealed headbox. Installation flexibility of remote control make the Orea 50 / 60 RTS ideal for cassette style awnings. Remote set limits with auto set over torque upper limit. Turning capacity limited only by thermal time. Suitable for tubes: 50 to 85. Memory Capacity: 12 channels / transmitters, plus 3 sensors. Programmable my position. Requires the use of a crown and wheel for tube adaptation. Horizontal mount only. Intermittent Usage.
OREA OREA OREA OREA RTS RTS RTS RTS 25/17 35/17 40/17 50/12
Torque (Nm) Torque (Nm) Torque (Nm) Torque (Nm) Speed (RPM) Speed (RPM) Speed (RPM) Speed (RPM) Ref. Ref. Ref. Ref. 1117119 1118090
OREA RTS 55/17 OREA RTS 85/17 OREA RTS 100/12
Torque (Nm) Torque (Nm) Torque (Nm) 100 Speed (RPM) Speed (RPM) Speed (RPM) 12 Ref. Ref. Ref. 1184058

[ Awnings: 6 ]

OREA 60 RTS 100/12

OREA 60 RTS 85/17

OREA 50 RTS 50/12

OREA 50 RTS 40/17

OREA 60 RTS 55/17

OREA 50 RTS 35/17

OREA 50 RTS 25/17

[ Awnings: 7 ]

OREA 50 WT OREA 60 WT
230V / 50Hz tubular motor. The Orea 50 / 60 WT is suitable for awning applications that require the use of a sealed cassette box. Available in torques from 25Nm to 100Nm, coupled with its flexible 48mm or 60mm (respectively) design, it is adapted for 50mm tubes and above. Electronically set limits and the adaptability of 230V control plus over torque upper limit functionality for a tightly sealed headbox make the Orea 50 / 60 WT ideal for cassette style awnings. Remote set limits with auto set over torque upper limit. Turning capacity limited only by thermal time. Suitable for tubes: 50 to 85. 230V switch control via mechanical or electronic means.* Requires the use of a crown and wheel for tube adaptation. Horizontal mount only. Intermittent Usage.

OREA OREA OREA OREA WT WT WT WT 25/17 35/17 40/17 50/12
Torque (Nm) Torque (Nm) Torque (Nm) Torque (Nm) Speed (RPM) Speed (RPM) Speed (RPM) Speed (RPM) Ref. Ref. Ref. Ref. 1117161 1118122
OREA WT 55/17 OREA WT 85/17 OREA WT 100/12
Torque (Nm) Torque (Nm) Torque (Nm) 100 Speed (RPM) Speed (RPM) Speed (RPM) 12 Ref. Ref. Ref. 1184082
*Direct switching of a 230V motor must always be done via a mechanical interlock.

[ Awnings: 8 ]

Blue = Neutral Brown = Active 1 Black = Active 2 Green/Yellow = Earth

OREA WT 55/17

OREA WT 25/17

OREA WT 100/12

OREA WT 50/12

OREA WT 40/17

OREA WT 85/17

OREA WT 35/17

0.50 x 1.5 2.4 0.75 IP44

1.50 x 1.5 2.4 0.75 IP44

1.63 x 1.5 4.4 0.75 IP44
1.160* x 1.5 5.4 0.75 IP44

[ Awnings: 9 ]

LT50 LT60
230V / 50Hz tubular motor. The LT50 / LT60 motors are suitable for a wide range of awning applications. Available in torques from 25Nm to 120Nm and with its flexible 48mm or 60mm (respectively) design, it is adapted for 50mm tubes and above. Rapid set push button limits and the availability of a wide range of 230v controllers make the LT50 and LT60 suitable all round performers. Rapid set limits. 46 turn limit capacity (LTturn capacity). Suitable for tubes: 50 to 85. 230V switch control via electronic or mechanical means*. Requires the use of a crown and wheel for tube adaptation. Horizontal mount only. Intermittent Usage.
GEMINI 25/17 HELIOS 30/17 MARINER 40/17 VECTRAN 50/12
Torque (Nm) Torque (Nm) Torque (Nm) Torque (Nm) Speed (RPM) Speed (RPM) Speed (RPM) Speed (RPM) Ref. Ref. Ref. Ref. 1049065 1051029
VEGA 60/12 SIRIUS 80/12 TITAN 100/12 TAURUS 120/12
Torque (Nm) Torque (Nm) Torque (Nm) Torque (Nm) Speed (RPM) Speed (RPM) Speed (RPM) Speed (RPM) Ref. Ref. Ref. Ref. 1166025 1167017
* Parallel wiring of motors is prohibited without the use of an isolation control, eg. 4AC Motor Controller, 4 Motor Group Controller etc. Direct switching of a 230V motor must always be done via a mechanical interlock.

[ Awnings: 10 ]

MARINER 40/17

VECTRAN 50/12

GEMINI 25/17

HELIOS 30/17

TAURUS 120/12

TITAN 100/12

SIRIUS 80/12

VEGA 60/12

L1 (mm) L2 riveting distance (mm) Torque (Nm) Speed (rpm) Turn Capacity Rated Voltage (V) Rated Power consumption (W) Rated Current (A) Running time before thermal cut off (min) Thermal cut off temp (C) Average running noise (dbA) Minimum tube diameter Motor weight (kg) Cable length (M) Number of cores in cable Cross section of cable (mm) Index Protection Approval

170 0.50 x 1.5 2.2 2.0.75 IP44
240 1.50 X 1.5 2.55 2.0.75 IP44
270 1.50 x 1.5 2.8 2.0.75 IP44
240 1.50 x 1.5 2.55 2.0.75 IP44
280 1.63 x 1.5 3.92 2.0.75 IP44
320 1.63 x 1.5 4.19 2.0.75 IP44
410 1.63 x 1.5 4.68 2.0.75 IP44
450 2.150* x 1.5 4.45 2.0.75 IP44

[ Awnings: 11 ]

LT50 CSI LT60 CSI
230V / 50Hz tubular motor. The CSI (manual override) motor is suitable for awnings that require the added flexibility of manual crank operation. Available in torques from 25Nm (50mm) to 120Nm (60mm) the CSIs manual override function allows the versatility of operation even if power is not present. With utilisation of the same adaptors as the 50 and 60mm range and rapid set push button limits, the CSI motor is a great hardwired option for areas that are prone to power loss. Rapid set limits. 34 turn limit capacity. Suitable for tubes: 50 to 85. 230V switch control via electronic or mechanical means*. Requires the use of a crown and wheel for tube adaptation. Horizontal mount only. Intermittent Usage.
GEMINI 25/17 MARINER 40/17
Torque (Nm) Torque (Nm) Speed (RPM) Speed (RPM) Ref. Ref. 1043001 1049011
Torque (Nm) Torque (Nm) Torque (Nm) Torque (Nm) Speed (RPM) Speed (RPM) Speed (RPM) Speed (RPM) Ref. Ref. Ref. Ref. 1166002 1167003
* Parallel wiring of motors is prohibited without the use of an isolation controller, eg. 4AC Motor Controller, 4 Motor Group Controller, etc. Direct switching of a 230V motor must always be done via a mechanical interlock.

[ Awnings: 12 ]

2 Holes at 6.apart
170 0.50 x 1.5 2.81 2.0.75 IP44
270 1.50 x 1.5 3.38 2.0.75 IP44
240 1.63 x 1.5 4.67 2.0.75 IP44
290 1.63 x 1.5 4.93 2.0.75 IP44
350 1.63 x 1.5 5.4 2.0.75 IP44
140* x 1.5 5.56 2.0.75 IP44

400 1.8 4

[ Awnings: 13 ]
Information about the noise is according to Somfy measures and is for information only. Taken as the worst value in load, for the up direction during the rst 10 seconds of travel.

LT50 CSI RTS

230V / 50Hz tubular motor The CSI (Manual Override) RTS (Radio Technology Somfy) motor is suitable for a wide range of awning application types. Available in torques from 20Nm to 50Nm, the CSIs manual override function allows the versatility of operation even if power is not present*. With utilisation of the same adaptors as the 50mm range, rapid set push button limits and RTS functionality, the CSI motor is a great remote option for areas that are prone to power loss. Rapid set limits. 34 turn limit capacity. Suitable for tubes: 50 to 85. Memory capacity: 12 Channels / transmitters, plus 3 sensors. 2 programmable "my" positions. Requires the use of a crown and wheel for tube adaptation. Horizontal mount only. Intermittent Usage.

METEOR CSI RTS 20/17 HELIOS CSI RTS 30/17 MARINER CSI RTS 40/12 VECTRAN CSI RTS 50/12
Torque (Nm) Torque (Nm) Torque (Nm) Torque (Nm) Speed (RPM) Speed (RPM) Speed (RPM) Speed (RPM) Ref. Ref. Ref. Ref. 1049037 1051017
* RTS functionality is not available if power is lost to the motor.

[ Awnings: 14 ]

MARINER CSI RTS 40/12

VECTRAN CSI RTS 50/12

METEOR CSI RTS 20/17

HELIOS CSI RTS 30/17

2 Holes at 6.4, 86 apart
160 0.50 x 1.5 2.96 2.0.75 IP44
240 1.50 x 1.5 3.21 2.0.75 IP44
Normal functioning temperature: -10C to +40C [ Awnings: 15 ]

PHOENIX

230V / 50Hz shaft drive motor. The Phoenix motor has long been used to motorise greenhouse louvres and as a retrofit to older style folding arm awnings that are normally operated via a crank handle. Still utilising a manual override operation when needed the Phoenix motor is a high torque, shaft driving, enclosed unit. With its unique design it allows for a relatively simple fit to an existing awning. Progressive limits. 38 turn limit capacity. Suitable for: 13, 14 and 19mm square shafts. 230V switch control via electronic or mechanical means.* Requires the use of adaptors depending on drive method. Vertical mount only. Intermittent Usage.

PHOENIX 50/12

Torque (Nm)

Speed (RPM)

1205001
*Parallel wiring of motors is prohibited without the use of an isolation controller, eg. 4AC Motor Controller, 4 Motor Group Controller, etc. Direct switching of a 230V motor must always be done via a mechanical interlock. Adaptors required for 13mm and 14mm shafts.

[ Awnings: 16 ]

171 61
Torque (Nm) Speed (rpm) Turn Capacity Rated Voltage (V) Rated Power Consumption (W) Rated Current (A) Running time before thermal cut off (min) Thermal cut off temp (C) Average running noise (dbA) Motor weight (kg) Cable length (M) Number of cores in cable Cross section of cable (mm) Index Protection Approval

390 1.5.5 2.0.75 IP33

38 230
Normal functioning temperature: -10C to +40C [ Awnings: 17 ]
ADAPTORS 50mm, 60mm MOTORS

Tube Profile

Crown Wheel Crown

Ref. Ref.

9751013 9707033

60 x 1.5 Round

Wheel Crown

9751013 9707029

60 x 2.0 Round

9751002 9707030

Issey 63

Sunmaster 65

9751005 9707034
Rochling, Perma, Turnils 70

[ Awnings: 18 ]

Tube Profile Wheel

Crown Wheel

9751005 9128424

Imbac 70

9410303 9128429

Franciaflex 70

Ref. Ref. Ref.

9277167

Perma, HD, Turnils 70

Crown 1 Crown 2

9761001 9707027
Dohner, Issey, Turnils 78

9761003 9707035

Issey 85

[ Awnings: 19 ]

9206019

63 Round

No Crown Adaptor Required

9761011 9277167

9761010 9700978

Schenker 75

9761005 9701051

Dohner, Turnils 78

9761001 9705341
Dohner, Aluxor, Issey, 78

9761003 9707641

Dohner, Issey 85

9420300 9690085

Imbac 85

[ Awnings: 20 ]

MOTOR BRACKETS 50mm, 60mm MOTORS

50mm, 60mm

U N I V E R SA L Z A M ACK B R ACKE T
Fix Points: - 2 holes 6mm, 48mm apart. - 2 holes 8mm, 60mm apart. - 2 holes 8mm, 60mm apart with bolt head. Maximum Torque: 85 Nm Ref.
HIGH LOAD BRACKET 50/60mm

157 110

Three points for fixing bolts: - m6, 44mm and 48mm. - m8, 60mm. Dimensions: 157h x 120w x 60d. Maximum Torque: 120 Nm Ref.

9910000

9430601
UNIVERSAL ZAMACK THREADED
Threaded holes for fixing bolts: -m6, 48mm apart. -m8, 60mm apart. -2 holes 8mm, 60mm apart with bolt head. Maximum Torque: 85 Nm Ref.

9910001

UNIVERSAL ZAMACK BRACKET WITH LOCKING RING
Fix Points: -2 holes 6mm, 48mm apart. -2 holes 8mm, 60mm apart. -2 holes 8mm, 60mm apart with bolt head. Maximum Torque: 120 Nm Ref.

9910003

[ Awnings: 21 ]
MOTOR BRACKETS 50mm CSI, 60mm CSI MOTORS

50mm CSI, 60mm CSI

SQUARE BRACKETS WITH MULTIPLE FIXING POINTS
Square Bracket with multiple xing points Three threaded bracket mounting points: - m6, 44mm and 48mm apart. - m8, 60mm apart. - 2 holes, 60mm & 44mm apart with bolt head. Maximum Torque: 120 Nm Ref.
UNIVERSAL FIX POSITION BRACKET
Three point mounting: - m6, 86mm apart. Two point Motor xing. - m6, 48mm with a point for 120 positioning.
Maximum Torque: 50 Nm Ref.

9910040

9410658

LT TO CSI BRACKET

Allows for the use of a Zamack bracket with a CSI motor. Fixed with two supplied screws. Use with ref. 9910001, 9910000. Maximum Torque: 85 Nm Ref.

30 FIX POSITION BRACKET

Three point mounting: - m6, 86mm apart. 30 motor xing.
Maximum Torque: 85 Nm Ref.

9910051

9420654

[ Awnings: 22 ]

BEARINGS 50mm, 60mm MOTORS

HIGH LOAD PLUG END SHAFT

16 pin end. Two wheels are required for use. For use with bracket ref: 9430603. Maximum load: Plastic Wheels 172 kgs. Aluminium wheels 250 kgs. Maximum Torque: 120Nm Ref.
SPRING LOADED PLUG END 12
Length adjustment of: 30mm. Crown and Wheel adaptor required. (see 50 adaptors). Maximum Torque: 50Nm Ref.

9420674

9685181 9420801
SPRING LOADED PLUG END 10
SPRING LOADED PLUG END 14
Length adjustment of: 30mm. Crown and Wheel adaptor required. (see adaptors section). Maximum Torque: 50Nm Ref.

9685181 9420800

9420802
CROWN & WHEEL MOUNTING FOR SPRING LOADED PLUG ENDS When utilising the bearings, a crown and wheel must be fixed to the item to ensure correct operation.

[ Awnings: 23 ]

PLUG END BRACKETS 50mm, 60mm MOTORS

HOLDER FOR BALL

For use with ball ref: 9028665.

NYLON BALL

12 bore. For use with holder ref: 1781030.

Maximum Torque: 50 Nm

9685181 1781030

9685181 9028665

HIGH LOA D INTERMEDIATE SUPPORT
Four wheels to suit the tube being used are required with this bracket. (see adaptors section). Maximum Torque: 120 Nm Ref.
H I G H LO A D PLU G E N D B R ACKE T
Adjustable saddle holder to suit: 9420674. Dimensions: 157h x 120w x 60d.
Maximum Torque: 120 Nm Ref.

9685181 9420673

9685181 9430603

[ Awnings: 24 ]

CSI ACCESSORIES 50mm CSI, 60mm CSI MOTORS
CRANK HANDLE WITH HOOK 1250mm
CRANK HANDLE WITH HOOK 2000mm

9129671

9129674
S H O RT E Y E O U T L E T m m
LON G E Y E O U T L E T m m

9685114

9685136

[ Awnings: 25 ]

PHOENIX ACCESSORIES PHOENIX MOTOR
PHO E N I X A N G L E B R ACKE T
Adjustable position angle bracket for Phoenix motor. Painted in Epoxy colour cream. Dimensions: 190h x 124w x 50d.
S Q U A R E PLU G E N D B R ACKE T
Mounting bracket with locking screw for nylon bearing. For use with ref. 1781015.
Maximum Torque: 55 Nm Ref.

9129686

9127808

BUSH ADAPTOR 13mm

For use with Phoenix Motor. Allows for a 13mm shaft to be used with the standard 19mm drive.

BUSH ADAPTOR 14mm

For use with Phoenix motor. Allows for a 14mm shaft to be used with the standard 19mm drive.

9129576

9129577

NYLON BEARING

12 bearing for Phoenix motor used with end bracket. For use with ref. 9127808.

1781015

PHOENIX EXPLODED DIAGRAM

[ Awnings: 26 ]

CABLES
NOTE: It is important to observe local wiring regulations before tting Somfy Motors.

H I RSCH MA N N CO N N EC TO R F O R S U P P LY ( BL ACK)
H I RSCH MA N N CO N N EC TO R F O R M OTO R ( BL ACK)
Detachable high protection connector: 3 terminals + earth. IP54 rating. Weight: 30g. Connectors can be tted to RTS and WT cables. Supplied not connected. Ref. 9686064
Detachable high protection connector: 3 terminals + earth. IP54 rating. Weight: 30g. Connectors can be tted to RTS and WT cables. Supplied not connected. Ref. 9686065
HI-PRO MOTOR CABLE VVF WHITE
VVF white cable. Four cores (blue, black, brown and green/ yellow). 0.75mm cross section. Suitable for LT 50/ 60 motors.

Ref. Length.

9203802 2.5m

9203804 5m

9203805 10m
HI-PRO MOTOR CABLE RRF BL ACK
RRF black cable. Four cores (blue, black, brown and green/ yellow). 0.75mm cross section. Suitable for LT 50/ 60 motors.

9203834 3m

9203839 10m
RTS MOTOR CABLE VVF WHITE
VVF white cable. Three cores (blue, brown and green/ yellow). 0.75mm cross section. Suitable for RTS 50/ 60 motors.

9001647 3m

9001648 5m

9001659 10m

[ Awnings: 27 ]
RTS MOTOR CABLE RRF BL ACK
RRF black cable. Three cores (blue, brown and green/ yellow). 0.75mm cross section. Suitable for RTS 50/ 60 motors.

9001654 3m

CSI MOTOR CABLE VVF WHITE
VVF white cable. Four cores (blue, black, brown and green/ yellow). 0.75mm cross section. Suitable for C.S.I 50/ 60 motors.

9208282 2.5m

[ Awnings: 28 ]
TEST LEAD & LIMIT ADJUSTERS
TEST LEAD FOR RT S MOTORS

WORKSHOP CONTROL BOX

For use with RTS motors. 3m cable with quick clip connectors. Power illumination. Ref.
For standard motors in a high use environment.

QUICK TEST

9686071

9001603

UN IVERSAL TEST LEAD
For use with Orea or Oximo WT motors, RTS motors, LS40/LT50 or LT60 motors. 3m cable with quick clip connectors.

9014459

[ Awnings: 29 ]