SOMFY UL approved controls can be found in UL File No. E160923
Guidelines for Selecting SOMFY SYSTEMS Electronic Products
Installations of dual direction motors require flexibility of control and compatibility not only with decor, but also with security, lighting, and environmental control systems. All SOMFY SYSTEMS control products are designed to maximize utility and aesthetics, as you will see in the catalog pages that follow. This section will help in selecting the devices that fit your application best by explaining the general options in a motor control system.

Window Treatment

Electronic Control
Why Do I need Motor Controls?
The design characteristics of an AC dual direction tubular motor which enable it to generate enough torque to raise awnings, shutters or shades, require several considerations in the design of its control circuit. First, these motors cannot be wired in parallel from a single switch as lighting fixtures can. There must be a SOMFY control device which prevents electrical feedback through the motor capacitor, such as a Group Controller or a network of Individual-Group controls. Second, one SOMFY motor cannot be controlled from several locations (switches) without a control device to build priorities among switch signals. A SOMFY Multi-Switch Command (MSC) or an Individual-Group Control (IGC) would apply here.

Group Control

Group of Motors

Two or more Switches

What is low voltage control or low voltage input?
Low voltage control refers to switch and automatic control inputs which interface with 120 volt AC motor controls. Low voltage (usually 12 volts DC) provided by the motor controller supplies the switches and allows for a more flexible system design than can be found with a 120 VAC or line voltage switch network. Low voltage wiring eliminates some of the hazards of line voltage, and is accomplished safely with inexpensive low voltage rated wire or modular cable. DC motors, by definition, include low voltage controls. The wiring requirements for DC motors are different than described above, and will be discussed later in this section.
MOTORIZATION CONCEPTS (Cont'd)
AC MOTOR CONTROL Switches
Switches are the most common interface between the user and the motor or motor controller. SOMFY offers a line of elegant switches made exclusively for motor control. These switches feature up, down, and stop positions in both momentary and maintained configurations for hardwired AC control of a single motor. Momentary switches will continue to drive the motor in a given direction as long as that switch direction is depressed, or until the motor reaches its limit in that direction. Maintained switches can be pressed and released and the motor will travel to its limit in the chosen direction. If you are required to control a single motor from two or more locations, it will be necessary to have all the switches interface with a SOMFY Multi-Switch Command unit. If one switch is required to control two or more motors, you will need to review the Group Control products.

Decorator Toggle Switch (Maintained - Ivory) Decorator Toggle Switch (Maintained - White) Decorator Toggle Switch (Momentary - Ivory) Decorator Toggle Switch (Momentary - White)

6120747 6120748

Rocker Switch Kit w/Alum. Std. Plate (Maintained - White) 6120405 Rocker Switch Kit w/Alum. Std. Plate (Momentary - White) 6120416

DECORATOR IGC SWITCH

The Decorator IGC switch line is designed for use with SOMFY's IGC and IGC/3N1 controls. This switch features a 6 pin modular connector which takes advantage of modular cable to connect it to a motor controller. The IGC Switch can be used for individual or group control. Both single and double switch stations come in white and ivory, and feature UP STOP and DOWN buttons. The , soft contours and neutral colors complement any decor.
MECHANICAL SPECIFICATIONS
Overall Dimensions: L: 4 /2 in. W: 2 /4 in. D: 1 /2 in. Installs in a standard single gang electrical box.
The Decorator IGC Switches are compatible with these SOMFY Products: IGC IGC/3N1 IGC II IGC/3N1 II MCIR IGC-DC Synchronizing Control DC5 HRC-IR HRC-RF Wind-a-Matic II Cat. No. 6300717 Cat. No. 6300719 Cat. No. 6300817 Cat. No. 6300819 Cat. No. 6300885 Cat. No. 6300843, 6300840 Cat. No. 6300889 Cat. No. 6300370 Cat. No. 6300983 Cat. No 6300982 Cat. No. 6300998

CONNECTION DIAGRAM

FRONT VIEW

REAR VIEW

Left Station Connectors Right Station Connectors
IGC SWITCH WITH MODULAR CONNECTORS

LEFT STATION

RIGHT STATION

Left Station Connectors

Right Station Connectors
IGC SWITCH WITH TERMINAL BLOCKS

U D C U D C

LEFT STATION RIGHT STATION

APPLICATION

Below is an illustration of how the Decorator IGC switches are used in conjunction with the SOMFY IGC, IGC/3N1 and the IGC SubGroup Control to create individual motor, group motor, floor control and master (entire house) control.

MODULAR CABLE

IGC IGC/3N1

STOP STOP STOP STOP

SUB-GROUP CONTROL

INDIVIDUAL CONTROL

ROOM CONTROL

MASTER CONTROL

MODULAR CABLE DETAILS

TAB FACING AWAY

WHITE BLACK RED GREEN YELLOW BLUE

PIN NO.

FUNCTION

UP DOWN +12 VDC COMMON NOT USED NOT USED
6 Conductor Flat Modular Cable 6 Position, 6 Pin Modular Connector

PIN 6 PIN 1

W H I T E

B R L E A D C K

G Y R E E L E L N O W

B L U E

ORDERING INFORMATION
Description Single IGC Switch (White) Single IGC Switch (Ivory) Dual IGC Switch (White) Dual IGC Switch (Ivory)
Catalog Number 6300909 6300938
Description Single IGC Switch with Terminals (White) Single IGC Switch with Terminals (Ivory) Dual IGC Switch with Terminals (White) Dual IGC Switch with Terminals (Ivory)
Catalog Number 6300041 6300141

DECORATOR RTS SWITCH

The Decorator RTS Switch (single or four channel) is a wireless radio switch compatible with all the RTS Motors, and externally mounted RTS receivers. It will operate window coverings at a distance with no wiring between the switch and motor or receiver. Commands are transmitted by radio waves at 433.42 MHz.
Overall Dimensions: L: 4 /2 in.
ELECTRICAL SPECIFICATIONS

D: 1 /4 in.

W: 2 /4 in.
Power: 3V Lithium battery, Cr2430 Frequency: 433.42 Mhz
Operating Temperature: 41 F to 104 F Frequency Range (optimal conditions): 65 ft. Installs in a standard, plastic, single gang electrical box.
GENERAL OPERATING INSTRUCTIONS
NOTE: Please Consult RTS Motor or Receiver Instructions for Specific Product Details.
1. Place the RTS Motor or Receiver in Programming Mode as described in the Operating Instructions. 2. Press the programming button on the side of the RTS Switch to program it in the memory of the RTS Motor or Receiver. Be sure the channel is first selected on the four channel model. 3. Pressing the UP button will raise the window covering, while pressing the DOWN button will lower it. To stop the window covering, simply press the STOP button. 4. Pressing the Channel Selector button on the 4-Channel Switch will sequence through the channels. Each LED will light to indicate the channel selected. The Master or 5th channel is indicated when all LEDs are lit.

FRONT Programming Button

Channel Selector Select the Channel Press the Programming Button
Description Single Channel RTS Switch - White Single Channel RTS Switch - Ivory Catalog Number Description Four Channel RTS Switch - White Four Channel RTS Switch - Ivory Catalog Number 6301025 6301035

CHRONIS RTS TIMER

SOMFYs new Chronis RTS Timer is a wireless digital timer compatible with all the RTS Motors and externally mounted RTS Receivers such as the Centralis. It will automatically raise and lower window treatments based on the pre-set time of day. The Chronis can be programmed to operate at the same time each day or different times every day. It has a security function that will raise or lower shades randomly to give the impression of an occupied home. Commands are transmitted via radio, so external wiring is not necessary.

OPERATING AND PROGRAMMING INSTRUCTIONS

SINGLE MOTOR REMOTE

MOTOR GROUND NEUTRAL HOT

TO NEXT IGC

RADIO RECEIVER
The IGC Outdoor Digital Keypad comes factory programmed with codes for UP DOWN, and STOP When the UP code is entered, the keypad will ,. command the IGC to raise the shutter or grille. Similarly, the shutter or grille will lower when the DOWN code is entered. To keep secure access, the codes can be reprogrammed by following these steps:
KEYPAD ENTRY *382436# *193# *11UUU#3# *11SSS#34# *11DDD#4# *2301# *2401# *99# FUNCTION Enter programming mode Set code length to 3 digits UUU is the UP code (enter desired digits) SSS is the STOP code DDD is the DOWN code Set output pulse width Exit programming mode
The Digital Keypad for Remote Control comes programmed with a single security code. Every time the code is entered, the Remote Control will sequence through UP STOP DOWN, STOP , ,. Follow these steps to change the security code: 1. Locate the code bank on the decoder module. It has 17 socket positions (*, 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, #) which are printed on the circuit board. 2. Socket positions A B C D E represent the five possible digits of the operating code. Socket position A is the first digit, while E is the last digit of the code. 3. Place one end of a program jumper wire (preinstalled) in socket A and the other end in the desired first digit. Repeat this process for B, C, D, and E. NOTE: You may not use the same number twice in the operating code. 4. Attach the decoder to the keypad. Locate the 13 position socket marked S2 on the decoder board. Align socket S2 with the 13 positions on the keyboard and carefully press the socket onto the pins.
Description Outdoor Digital Key Pad for IGC IGC Controller 2 Gang Electrical Box Catalog Number 5670323 Description Indoor Digital Key Pad for Remote Control Outdoor Digital Key Pad for Remote Control Remote Controller Catalog Number 6300690

KEY SWITCHES

SOMFY's line of high-security outdoor Key Switches are protected by a tamper proof cover that cannot be removed without inserting the key. They are available with flush or surface mounting and maintained or momentary switching. SOMFY also offers several indoor Key Switches for those areas that require enhanced security. These Key Switches include heavy duty and light duty models with either momentary or maintained operation.

120VAC

HOT NEUTRAL

REAR OF SWITCH

BLACK RED
Outdoor Key Switches Heavy Duty Momentary Outdoor Key Switch (surface mount) Heavy Duty Momentary Outdoor Key Switch (flush mount) Heavy Duty Maintained Outdoor Key Switch (surface mount) Heavy Duty Maintained Outdoor Key Switch (flush mount) Key Blanks for Outdoor Key Switches Rain Hoods for Outdoor Key Switches Keyed Alike Key Switch Cylinder Note: Upon special request, Key Switches can be keyed alike. Indoor Key Switches Heavy Duty Momentary Indoor Key Switch Heavy Duty Maintained Indoor Key Switch Light Duty Momentary Indoor Key Switch DP/DT Momentary Indoor Key Switch DP/DT Maintained Indoor Key Switch Key for Heavy Duty Indoor Switch Key for Light Duty Momentary Indoor Switch 6110293 Catalog Number 6110772
Individual and Group Controls
Individual-Group Control for DC Motors (IGC-DC)

DC-5 Control

GCS II
Group Control System II (GCS II)
Individual-Group Control (IGC and IGC/3N1)

STOP STOP STOP

Individual-Group Control II (IGC II and IGC II/3N1)

IGC-II/3N1

Subgroup Controller

Moduline System

INDIVIDUAL GROUP CONTROL SYSTEM FOR DC MOTORS (IGC-DC)
The IGC-DC provides control of one or more DC motors in groups and/or individually from one or more locations. It provides both lift and tilt capabilities for horizontal blind applications. The IGCDC is a very flexible control system that can be configured in a variety of ways (i.e.; individual window control, floor control, total building control, etc.) to meet the requirements of your customers. Unlike the IGC, the IGC-DC is a switch and motor controller all in one package, and can be installed in a single gang electrical box.
MECHANICAL SPECIFICATIONS:
Overall Dimensions: L: 4 1/2 in. W: 2 3/4 in. D: 1 1/8 in.
Voltage Rating: INPUT: 12 or 24 VDC
Installs in a standard single gang electrical box. Approvals:
OUTPUT: 12 or 24 VDC 750mA per motor Complies with the National Electrical Code (NEC) Standard

RECOMMENDED TRANSFORMERS

MOTOR TYPE LT28A LT28B LV25-B44 LV25-B64 LW25-B83 LT28-HMOTOR 2 MOTOR 3 MOTOR 4 MOTOR 5 MOTOR 5700098 5700098

RELAY RELAY

To Motor(s)

(5 motors max.)

DIRECTION 1 + 12/24VDC Power Input COMMON DIRECTION 2 Master Line Connection COMMON

MOTOR CONTROL EXAMPLES

3 DC Motors Individually Controlled 3 DC Motors Controlled Individually & as a Group
Master Line 3 IGC-DC Switches 3 IGC-DC Switches

To Power Supply

Decorator IGC Switch
15 DC Motors Controlled as a Group & in Sub-Groups
Master Line Master Switch IGC-DC IGC-DC IGC-DC Decorator IGC Switch To Power Supply To Power Supply To Power Supply
NOTE: Group control is accomplished by terminating the master link on a Decorator IGC Switch as shown.

4. When the monitored wind speed is greater than the DSM setting, the UP direction will activate after 2 seconds. The wind LED will remain on as long as this condition exists. When the wind speed drops below the set value, the DSM will return to normal mode after 15 minutes. The wind LED will blink and the motors are prevented from operating during this period. 5. When the AUTO button is pressed, the AUTO LED will turn on or off depending on its previous status. Manual mode is designated by the LED being off. If the DSM is in manual mode, the sun level has no influence on motor control. The wind speed is constantly monitored and acted on regardless of AUTO setting.

DSM WIRING DIAGRAM

MOTOR SUN SENSOR WIND SENSOR
NOTE: When using a GCS II, the sun and wind sensors can be connected to the GCS II instead of the DSM if convenient.

BLACK BROWN

S W + U I 12 N N V D
TO REMOTE SWITCH NO CONNECTION

TO REMOTE SWITCH

TO IGC OR GCS II

DSM - SINGLE MOTOR

DSM - IGC/GCS II MODEL
Description DSM - Single Motor DSM - IGC DSM - GCS II OPTIONS Wind Sensor Sun Sensor and Bracket Enclosure for Surface Mount Option (Single Motor) Enclosure for Surface Mount Option (IGC/GCS II) Optional Switch Radio Remote Kit Catalog Number 6300899 (White) 6300929 (Ivory) 6300895 (White) 6300925 (Ivory) 6300903 (White) 6300933 (Ivory)
6300908 (White) 6300937 (Ivory) 6300448
DECORATOR SOMFY-MATIC OUTDOOR PLUG-IN SYSTEM
The Outdoor Decorator Somfy-Matic (DSM) enables a retractable awning to provide shading from the sun and protection from the wind automatically and conveniently. The sun and wind sensors continually monitor sun intensity and wind speed. These settings can be adjusted from the faceplate and will trigger the control unit to extend or retract the awning as needed. The Outdoor DSM features advanced circuitry that assures factory preset accuracy and proven reliability. It helps protect furniture and carpeting from fading and saves on heating and air conditioning costs. The system is comprised of plug-in components, so installation is quick and simple.
Overall Dimensions: Operating Temperature Range: Wind Speed: L: 4 5/8 in. W: 4 3/8 in. D: 3 1/2 in.

DCC WIRING DIAGRAMS

CAUTION: Before proceeding with the line voltage wiring instructions, the up and down limits of each motor should be set using the SOMFY tester cable (Cat. No. 6020086). Refer to limit switch instructions packaged with each SOMFY motor for more information. NOTE: When using a GCS II, the sun sensor can be connected to the GCS II instead of the DCC if convenient.

BROWN RED WHITE

BROWN BLUE

TO IGC OR GCS

DCC - SINGLE MOTOR

DCC - IGC/GCS MODEL

Description DCC - Single Motor DCC - IGC DCC - GCS II OPTIONS: Sun Sensor and Bracket Enclosure for Surface Mount Option (Single Motor) Enclosure for Surface Mount Option (IGC/GCS II) Optional Switch Radio Remote Kit Catalog Number 6300901 (White) 6300897 (White) 6300905 (White) 6300931 (Ivory) 6300927 (Ivory) 6300935 (Ivory)

(White) 6300448

6300937 (Ivory)

WIND-A-MATIC II

The SOMFY Wind-a-Matic II is a single motor control designed for residential use. The unit features a wind sensor and an elegant indoor switch. Wind speed is continuously monitored, triggering the control to retract awnings or lower shutters automatically as needed. This control is packaged in a weatherproof enclosure and includes watertight strain-relief fittings for wires entering the box. The Wind-aMatic II is ideal for both new construction and home improvement, installing fast and easy near the motor and reducing overall wiring costs.
Overall Dimensions: Wind Speed: L: 4 5/8 in. 12 to 31 mph -20 to 50 Celsius

W: 4 5/8 in.

D: 2 1/2 in.
Operating Temperature Range:
Voltage Ratings: INPUT: OUTPUT: 120 VAC +/- 10% 120 VAC 5A 50/60 Hz. 1/4 HP
Approvals: The Wind-A-Matic II is UL508 (pending) for industrial controls (UL, cUL) Complies with the National Electrical Code (NEC) Standard
1. The Wind-a-Matic-II should be mounted as close to the motor as possible. If mounted outside, ensure that the connections are facing down to avoid moisture seepage. 2. Connect high and low voltage wires according to the wiring diagram on the next page. Make sure to use included watertight strain relief fittings to maintain the weatherproofing of the enclosure.
3. The wind sensor should be placed close to the awning or shading system to make sure the wind speed is measured at the product. Guard against installing the wind sensor too close to an obstruction such as a chimney, WIND-A-MATIC II CONTROL gutter or the awning itself, as this could block the wind and cause erroneous sensor readings. The sensor should not be more than 100 feet from the control. 4. Connect the low voltage switch according to the diagram on the next page. It should be mounted no more than 100 feet from the Wind-a-Matic-II.

WIND ADJUSTMENT SUN ADJUSTMENT PROGRAMMING BUTTON & LED
UP DOWN MTR COM NEUT HOT SUN WIND COM
TO OPTIONAL LOW VOLTAGE SWITCH

COMBINED SENSOR

TELIS TRANSMITTER
System Set Up 1. With power off, wire the Soliris Receiver as indicated. Turn all circuit breakers on (motors should not move). 2. Set the Soliris Receiver into programming mode by pressing the programming button until the LED lights (about 5 seconds). Press the programming button on the Telis1,Telis4 or Telis Soliris transmitter. The programming LED will blink indicating the transmitter has been memorized. 3. Operate each motor in the DOWN direction using the radio transmitter. The motorized product should move down or out. If this is incorrect, turn off the circuit breakers and reverse the red and black wires of the motor. FAILURE TO CORRECT THIS ERROR WILL CAUSE DAMAGE TO AWNING BY EXTENDING IT DURING WINDY CONDITIONS. Setting The Wind Level 1. To change the wind sensitivity, simply rotate the wind adjustment knob to the desired setting. All time delays are reduced at the Installation Mode setting.

INSTALLATION MODE

TRANSMITTER 1. Pressing the UP button on the Telis transmitter will move the exterior window covering up or in. The DOWN button will move it down or out. 2. To stop the motorized product at any time, press the CENTER button on the transmitter. 3. Pressing the SUN/WIND button on the Telis Soliris Transmitter will toggle between wind only and sun and wind operation. When the wind only function is selected, the Soliris Receiver will not activate according to the sun levels. SUN FUNCTION 4. When the measured sun intensity is greater than the set level, a DOWN command is given. 5. When the sun intensity falls below the set level, the awning or exterior screen will retract automatically after a 20 minute delay. WIND FUNCTION 6. When the monitored wind speed is greater than the setting, the UP direction will activate after 2 seconds. As long as the wind speed remains high, all other commands will be ignored. 7. When the wind speed drops below the set value, the Soliris Receiver will extend the awning automatically after a 12 minute delay. However, a manual command can be given with the radio transmitter after only one minute. LOW VOLTAGE SWITCH 8. An optional single pole, single throw switch can be connected to the low voltage terminals. Each press of the switch will sequence through the directions as follows: DEPRESS 1 UP DIRECTION DEPRESS 2 STOP DEPRESS 3 DOWN DIRECTION DEPRESS 4 STOP
Setting The Sun Level 1. To change the sun sensitivity, simply rotate the sun adjustment knob to the desired setting.

Sun Adjustment Detail

37 50KLUX
Description Soliris Receiver Kit (control & combined sensor) Soliris Receiver (control only) Soliris Sensor Telis Soliris Transmitter SPST Momentary Switch Catalog Number 6300080 (White) Description Telis Transmitter Telis 4 Transmitter Decorator RTS Switch Decorator RTS Switch (4 Channel) Chronis RTS Timer Catalog Number 6301033 (White), 6301034 (Ivory) 6301025 (White), 6301035 (Ivory) 6300383
TELIS SOLIRIS TRANSMITTER
The Telis Soliris Transmitter is a single channel hand-held transmitter compatible with the Soliris Receiver, Altus motor and Soliris RTS Sensor. It will operate window coverings at a distance as well as switch between Wind-Only or Sun & Wind Modes.

Catalog No: 6301017

Overall Dimensions: L: 4 /4 in.

D: /4 in.

W: 1 /4 in.
Power: 3V Lithium batter, Cr2430 Frequency: 433.42 Mhz
NOTE: Please Consult Altus Motor or Soliris Receiver Instructions for Specific Product Details.
1. Place the Altus Motor or Soliris Receiver in Programming Mode as described in the Operating Instructions. 2. Press the programming button on the back of the Telis Soliris to program it into the memory of the Altus Motor or Soliris Receiver. 3. Pressing the UP button will raise the window covering, while pressing the DOWN button will lower it. To stop the window covering, simply press the STOP button. 4. Pressing the Mode Selector button will switch between Wind-Only and Sun & Wind Modes. The corresponding LED will light to indicate the mode selected.
FRONT UP STOP DOWN Programming Button Sun/Wind Selector BACK
SOLIRIS & EOLIS RTS SENSOR
The SOMFY Soliris RTS and Eolis RTS sensors are 24V radio sensors compatible with the Altus and LT CMO RTS motors. The Eolis is a wind only, while the Soliris is a combined sun and wind sensor. Sun intensity and wind speed thresholds can be set right on the sensor. The RTS Sensors will command the motor to extend or retract an awning as needed, via radio signal. It comes with a 24V DC transformer to provide power, otherwise additional wiring is not needed.
Overall Dimensions: L: 9 /3 in.

SOMFY's Remote Control line provides motor control from a distance through the use of a hand held radio transmitter. For convenience, kits of up to four Single Motor Remotes are available with individual control of all motors from a single transmitter. The Single Motor Remote Control features normallyclosed input terminals, to be used when starting a motor would cause damage to an open door or window. This input would interface with a window alarm contact and disable the control when the window or door is open. The Remote Control also has dry-contact output capability. This enables the control to operate other devices, such as SOMFYs GCS-II.
Overall Dimensions: Remote: Receiver: L: 3 1/2 in. L: 3 in. 75 ft. W: 3 1/4 in. W: 4 3/4 in. D: 2 1/4 in. D: 1 3/8 in.
Remote Control fits in a standard 2 gang masonry electrical box
Voltage Ratings: INPUT: OUTPUT: 120 VAC +/- 10% 120 VAC Fuse 50/60 Hz 5A 5A 1/4 HP 115/230 VAC
Approvals: Complies with the National Electrical Code (NEC) Standard, UR, CSA, and FCC.
A. Single Motor Remote Control A single motor can be controlled from a remote switch or radio transmitter. Each press of the switch will sequence through the directions as follows; DEPRESS 1 DEPRESS 2 DEPRESS 3 DEPRESS 4 UP DIRECTION STOP DOWN DIRECTION STOP
SINGLE MOTOR REMOTE RADIO RECEIVER

RADIO TRANSMITTER

B. Multiple Motor Remote Control SOMFY's Single Motor Remote Control is prepackaged in kits for 2, 3, and 4 motor operation from a single transmitter. A 2 channel transmitter operates two motors, while the 4 channel transmitter operates up to four. Receivers should be mounted at least 10 feet apart.
SINGLE MOTOR REMOTE RADIO RECEIVER SINGLE MOTOR REMOTE RADIO RECEIVER SINGLE MOTOR REMOTE RADIO RECEIVER SINGLE MOTOR REMOTE RADIO RECEIVER
4 BUTTON RADIO TRANSMITTER
C. Group Control SOMFY's Group Control System (GCS-II) can be controlled by radio remote by connecting the Single Motor Remote Control to the Low Voltage Switch Connector on the GCS-II. This will provide group only remote control of up to four motors.
GCS - II (Cat. # 6300123)
RED BROWN YELLOW BLACK WHITE

120 VAC

Remote Control RED BROWN YELLOW
GCS-II Terminals UP DOWN COMMON
RADIO RECEIVER RADIO TRANSMITTER
Low voltage terminals are provided for interfacing to home automation or other third party systems. A momentary dry contact (relay) closure is required between the REMOTE SWITCH input and COMMON. This contact should remain closed at least 0.5 seconds, but no more than 1 second. Each closure will sequence through the commands as follows: UP STOP DOWN, STOP , ,.

INDIVIDUAL MASTER CONTROL OR MASTER ONLY OR DAISY CHAIN CONTROL

MOTOR 3

COMMON

+12 VDC

Low voltage terminals are provided for interfacing to home automation or other third party systems. A momentary contact (relay) closure is required between the motor input and common. For example, to activate Motor1, a contact closure is required between the MOTOR1 and COMMON terminals. This contact closure should be at least 0.5 seconds, but no more than one second. Each contact closure will sequence through UP STOP DOWN, STOP for each motor input. , , A contact closure between the MASTER terminal and COMMON will activate all the motors on the 3N1 Remote Control.
Accessories and Special Applications

RS 232

MultiSwitch Command

Synchronization Control

Fabric Tension System

LT28 Stall Sensor

ILT Controls LON Controls

Accessories

RS232 INTERFACE MODULE
The SOMFY RS232 Interface Module translates RS232 protocol for use with SOMFY controls. This unit can connect to any PC, home automation or lighting system. Each addressable device connects to one SOMFY control such as an IGC or MCIR. One RS232 module is required for each motor or group. The RS232 Interface makes it simple to control window coverings by computer.

Catalog No. 6300232

Overall Dimensions: L: 1 /4 in.

W: 3 in.

Mounts in a standard single gang box
Input Voltage: Output Voltage: 12V DC, 150mA (supplied by IGC or MCIR) 12V DC, 150mA, open collector

OPERATING SPECIFICATIONS

The RS232 Interface Module receives and translates UP STOP and DOWN commands. , The interface uses the following communication settings. Settings: 9600 Baud 8 Data Bits 1 Stop Bit No Parity
The SOMFY protocol is available upon request.

TX GROUND SERIAL CABLE

RS232 MODULE

ADDRESS SELECTORS

IN COM
TO POWER AND MOTOR MODULAR CABLE

B C DE

MULTI-SWITCH COMMAND
The Multi-Switch Command offers the convenience of controlling one operator, by more than one switch, from one or more locations. It correctly isolates different switches controlling the same motor. This protects the motor from receiving opposite commands at the same time. The Multi-Switch Command is activated by standard UP/DOWN momentary switches. It mounts in a standard single gang electrical box.

Catalog No. 6300427

Correct

One Motor, 2 Switches

Incorrect

Multi-Switch Command

MOMENTARY ROCKER SWITCH MULTI-SWITCH COMMAND STANDARD SWITCH BOX 2.5 " DEEP MOTOR DIRECTION 1 HOT DIRECTION 2 BLACK RED WHITE BLUE (DIR. 1) BROWN (DIR. 2) GREEN (GROUND) BLACK RED WHITE
HOT DIRECTION 2 DIRECTION 1 GROUND TO ADDITIONAL MOMENTARY SWITCHES STANDARD SWITCH BOX 2.5 " DEEP TO POWER SOURCE 120 VAC HOT NEUTRAL GROUND

FABRIC TENSION SYSTEM CONTROL (FTS)
The FTS is a specialized system designed for the solar protection market where horizontal or inclined type shading is required. The system consists of two specific motors, an electronic control unit and a switch. The control operates each motor independently and maintains a desirable dynamic (moving) tension as well as final tension in the system, eliminating fabric sag while the fabric is both moving and standing. Adjustments to both dynamic and final tension can be made through the electronic control For more complete information, refer to SOMFYs FTS instructions. SOMFYs motor and control warranties are based on strict adherence to these instructions.
Overall Dimensions: L: 8 in.
Voltage Rating: INPUT: Line Voltage: 115 VAC +/- 10% Low Voltage: 5 VDC 0.3 A 115 VAC 5A (each motor) Fuse: 10A

W: 10 in. D: 4 in.

Operating temperature range: 0 C to 40 C OUTPUT:

Approvals:

Complies with the National Electrical Code (NEC) Standard. UL approval pending.

FABRIC MOTOR

ELECTRONIC CONTROL

FABRIC

LOAD BAR STRAP STRAP MOTOR SWITCH

POWER SOURCE 120V AC

Description FTS Control Single IGC Switch FTS Tester Cable Catalog Number (White), 6300140 (Ivory) 6020087

LT28 STALL SENSOR

The Stall Sensor is used with interior window coverings that utilize SOMFYs LT28 DC motor. The sensor will cut power to the motor if the bottom of the window treatment meets the headrail before the motor reaches its limit. This prevents stretching of the fabric and extends motor life. This application is useful with certain fabrics that may change shape over time and thus change the actual upper limit. The stall sensor is not intended to replace the upper limit switch of the motor. NOTE: The LT28 must be modified to work with the Stall Sensor. Please consult the sales staff before ordering. The stall sensor is available as a stand-alone unit (shown right) with a designer switch or in an enclosure without a switch. With the enclosed Stall Sensor, a user may connect any low voltage switch to the input terminals.
Overall Dimensions: Stand Alone Unit: Enclosed Unit:
3 L: 2 /4 in. L: 3 1/2 in. 1 W: 4 /2 in. W: 2 1/4 in. 1 D: 1 /4 in. D: 1 1/2 in.
Voltage Ratings: INPUT: 12 VDC OUTPUT: 12 VDC 2A 750mA
Stand alone unit installs in a standard single gang box.
Approvals: Complies with the National Electrical Code Standards (NEC)
1. Pressing the switch UP or DOWN will move the motor in the appropriate direction. If the motor does not move in the correct direction, turn off the circuit breakers and reverse the motor wires at the terminal block.