SOMFY INSTRUCTIONS GLYSTRO 25 RTS

Part #s 1000177

The new Glystro 25 RTS is equipped with an improved RTS radio receiver technology. Based on the platform of the new Somfy RTS DC controller, the Glystro 25 RTS can access the programmed "MY" (preferred position) without having to be in a fully traversed (open or closed) drapery setting. Additionally, the motor output direction (drapery direction) can be reversed during the programming process, which allows for enhanced compatibility with other motorized window coverings.

Connect Power to Motor

Factory Mode (No controls previously programmed) 1. Plug the recommended power supply into the designated input jack located at the bottom of the Glystro 25 motor. Master carrier/drapery will jog. NOTE: A "jog" is a brief side to side movement of the master carrier or drapery if attached.

Initiate Programming

Temporary "Pairing" of Transmitter 1. On the Telis transmitter, briefly press the UP and DOWN buttons simultaneously, the master carrier/drapery will jog.
Polarity (Drapery Direction)
Confirming Correct Drapery Direction 1. On the transmitter, press and hold the UP button. If drapery traverses to the "OPEN" position, direction is correct. (Proceed to Changing Operational Mode pg2) If drapery traverses to the "CLOSED" position, direction must be reversed. (See Reversing drapery direction below) Reversing Drapery Direction 1. If drapery traverses to a "CLOSED" position, the directional output needs to be reversed. Simply press and hold the "MY" button until the drapery jogs. Direction is now reversed.

= OPEN Direction

= CLOSED Direction
2. Press and hold the UP button to confirm drapery now traverses to the "OPEN" position.
Copyright Somfy Systems, Inc. 10/2009

C-0018

PAGE 1 REV 3
Changing Operational Mode
The Operation mode effects the way the drapery responds when commanded by the Telis remote. In Maintained Mode: The drapery will respond to a brief press of the UP or DOWN button. The drapery will traverse to a full open or closed position unless commanded to stop my pressing the "MY" (stop) button.

my my my

In Momentary Mode: The drapery will respond only as the UP or DOWN button is held. Once the button is released, the drapery will stop. This function is best used when the drapery is not required to travel to a full open or closed position, but rather a short traverse for enhanced control convenience. The New Glystro 25RTS provides both Maintained & Momentary control as a factory default. If this (default) function is preferred, there is no need for additional programming (Skip Programming the Limits below and proceed to Completing and Exiting Programming Mode pg 2 & 3) If Maintained only mode is desired (no momentary control) follow the programming instructions (below) for MAINTAINED ONLY MODE. Maintained Only Mode (Optional) 1. Press and hold the "MY" and DOWN buttons simultaneously until the drapery jogs. Operational mode is now programmed for maintained mode only. NOTE: MAINTAINED COMMAND mode will not function until FINAL PROGRAMMING is completed.
Programming the Limits (Stop locations) *OPTIONAL
NOTE: This procedure must be preformed in order to utilize the "MY" (preferred stop position) If the "my" (preferred position) is not required, proceed to Completing and Exiting Programming Mode below Limit (stop location) Setting 1. Briefly press the "MY" (stop) and UP buttons simultaneously until drapery traverses to the full OPEN position. If drapery stops before reaching the OPEN end limit (stop location) press and hold the UP button until end limit is reached.

2. Briefly press the "MY" (stop) and DOWN buttons simultaneously until drapery traverses to the full CLOSED position. If drapery stops before reaching the CLOSED end limit (stop location) press and hold the DOWN button until end limit is reached. 3. Press and hold the "MY" (stop) until drapery jogs. Limit settings (Stop locations) are now programmed.
Completing and Exiting Programming Mode (User Mode)
Assigning the Transmitter to the Glystro Drapery Motor 1. Using a paperclip or pen, press and hold the Programming Button on the back side of the Telis transmitter until the drapery jogs. Transmitter is now memorized by Glystro motor.

Programming Button

PAGE 2 REV 3
Operating the Glystro25 RTS Motor (User Mode) Standard Default Operation (Maintained & Momentary Mode)
Maintained Mode 1. Briefly press the UP or DOWN button. Drapery will automatically traverse to a full OPEN or CLOSED position. Press the "MY" (stop) button to stop drapery while traversing. Momentary Mode 1. Press and hold the UP or DOWN button to open or close the drapery. Release button and drapery will stop.
Maintained Operation Only (OPTIONAL) 1. Briefly press the UP or DOWN button, drapery will automatically traverse to a full OPEN or CLOSED position. Press the "MY" (stop) button to stop drapery while traversing. NOTE: Maintained Only Mode (No Momentary Mode) is not possible unless previously programmed. See previous Changing Operational Mode section for details.
Programming a "MY" (Preferred Stop Position)
1. Press the UP or DOWN button to activate drapery to a preferred position. 2. Press and hold the "MY" (stop) until drapery jogs. The preferred "MY position is now programmed. Briefly press the "MY" button to operate drapery to the preferred position. Note: The "MY (preferred position) can be accessed from any drapery position.
Deleting a "MY" (Preferred Stop Position) 1. Activate the drapery to the pre-set "my" (preferred position) 2. Press and hold the "MY" button until the drapery jogs. The "my" (preferred position) is now deleted.
Resetting Glystro 25 RTS Motor
Deleting Previously Programmed Transmitters 1. Using a paper clip, pen or similar device, press and hold the Programming Button on the Glystro 25 RTS until the drapery jogs two times (approximately 7 seconds). Resetting Motor to Factory Mode 1. Using a paper clip, pen or similar device, press and hold the Programming Button on the Glystro 25 RTS until the drapery jogs three times (approximately 12 seconds).

www.somfy.com

Sonesse 30 DCT

Installation instructions

Ref :5051080A

SAFETY
This Somfy product must be installed by a professional motorization and home automation installer, for whom these instructions are intended. Before installation, check that this product is compatible with the associated equipment and accessories. These instructions describe how to install, commission and use this product. Moreover, the installer must comply with current standards and legislation in the country in which the product is being installed, and inform his customers of the operating and maintenance conditions for the product. Any use outside the sphere of application specified by Somfy is not approved. Such use, or any failure to comply with the instructions given herein will invalidate the warranty, and Somfy refuses to accept liability.

COMPATIBLE BLINDS

Venetian blinds Roman shades Roller blinds

COMPATIBLE CONTROL

Setting Tool

Centralis IB

Wall Switch
GENERAL SAFETY INSTRUCTION
The safety instructions that must be observed, besides the usual rules, are explained in these instructions and in the attached Safety Instructions document.
Never immerse the motor in liquid!

Avoid impacts!

Never drill holes in the motor!

Do not drop it!

Copyright 2008 Somfy SAS. All rights reserved - V0 - 11/2008

INSTALLATION

Motor preparation 1) Fit the crown (a) and drive wheel (b) to the motor. 2) Measure the length (L) between the middle of the drive wheel and the head end.
Tube preparation Cut the tube to the required length. Deburr the tube and remove the debris. Motor/tube assembly 1) Slide the motor into the tube.
2) Fix the tube to the motor with selftapping screws or steel pop rivets depending on the dimension (L).
Mounting the motorized tube on the brackets If necessary, screw the bracket interface on the motor head. Mount the motorized tube on the end bracket (C ). Mount the motorized tube on the motor bracket (D).

Wiring

Sonesse 30 DCT is Dry contact motor.It cant be controlled with power going through the setting tool cable.
1) Connect the power cable to the motor.
2 ) Connect the setting tool cable to the motor.
3) Control wiring Setting Tool 1 UP (White/Blue) 2 STOP (Blue) 3 DOWN (White/Orange) 4 GND (Orange) Centralis IB 1 UP or DOWN (White/Blue or White/ Orange) 2 UP or DOWN (White/Blue or White/ Orange) 3 GND (Orange) Wall Switch 1 UP or DOWN (White/Blue or White/ Orange) 2 UP or DOWN (White/Blue or White/ Orange) 3 GND (Orange) 4) Correspondence

COMMISSIONING

Checking the direction of rotation Press the setting tool UP button: a) If the shade is raised, the direction of rotation is correct. Move to the section entitled Adjusting the end limits. b) If the shade is lowered, the direction of rotation is incorrect. Move to the next step. Press the setting tool STOP button until the shade jogs: the direction of rotation has been modified. Press the setting tool UP button to check the direction of rotation.

Adjusting the end limits The limits can be set in any sequence. 1) Press and hold the UP button to move the shade to the desired up position. 2) Press simultaneously the STOP and DOWN buttons and release them once the shade begins to move. The up limit is memorized. 3) Press the STOP button when it reaches the desired down position. If necessary adjust the down position, using the UP or DOWN buttons. 4) Press simultaneously the STOP and UP buttons and release them when the shade begins to move. The down limit is memorized. The shade moves up and will stop at its upper limit. 5) To confirm the end limits press and hold the STOP button until the shade jogs. The end limits are recorded.
MY position 1) Recording MY position To set the MY position, move the shade to the desired position with the UP and DOWN buttons then press the STOP button until the shade jogs.
2) Changing the MY position To change the MY position go to the new desired MY position with the UP and DOWN buttons then press the STOP button until the shade jogs.
3) Delete the MY position To delete the MY position, move to this position and press the STOP button until the shade jogs.
Mode Selection By factory default, the motor is in Roller mode but you can change from a mode to another. To change from a Roller mode to a Tilting mode, press the UP, STOP and DOWN buttons simultaneously until the shade jogs.
With the setting tool, it is possible to cancel and exit the speed or limit adjustment mode by simultaneously pressing the UP, STOP, and DOWN buttons. These modes will also be cancelled with inactivity of 2 minutes.
Adjusting the roller speed 1) Press and hold the STOP button until the shade jogs twice. The shade moves up and down automatically in 10 second cycles. 2) While the shade is moving, briefly press the UP button to increase the speed or DOWN button to decrease the speed. 3) To confirm the new speed, press and hold the STOP button until the shade jogs.
Adjusting the Tilting speed 1) Press and hold the STOP button until the shade jogs 3 times. The shade moves up and down automatically in 10 second cycles. 2) While the shade is moving, briefly press the UP button to increase the speed or DOWN button to decrease the speed.

10s 10s

3) To confirm the new speed, press and hold the STOP button until the shade jogs.
UP, DOWN and MY In roller mode 1) To move the shade from a limit to the other limit, press briefly the UP or DOWN button.
2) To stop the shade, press the STOP button.
3) To move the shade to the MY position, press briefly the STOP button.
In tilting mode 1) To move the shade from a limit to the other limit, press briefly (less than 0,5s) the UP or DOWN button.
3) To move the shade to the MY position, press briefly the STOP button. The Venetian blind goes first to the down end-limit, then to the MY position. 4) To tilt the slats, press and hold the UP or DOWN button until the slats reach the desired position.

End limit re-adjustement UP LIMIT 1) Press the UP button, to move the shade to the limit to be readjusted. 2) Press and hold the DOWN and STOP buttons simultaneously until the shade jogs. 3) Press and hold the UP or DOWN button to move the shade to the new desired position. 4) To confirm the new limit press and hold the STOP button until the shade jogs.
DOWN LIMIT 1) Press the DOWN button, to move the shade to the limit to be readjusted. 2) Press and hold the STOP and UP buttons simultaneously until the shade jogs. 3) Press and hold the UP or DOWN button to move the shade to the new desired position. 4) To confirm the new limit press and hold the STOP button until the shade jogs.
Modifying the direction of rotation To reverse the rotation direction, press and hold all the three buttons simultaneously until the shade jogs twice.
Erasing the memory of the motor. Press and hold all the three buttons simultaneously until the shade jogs 3 times. All the settings are erased.

Technical data

Voltage Operating temperature Protection rating Torque Adjustable Speed Roller Speed (By default) Tilting Speed (By default)
24V 0C / 60 C IPNm rpm 28 rpm 16 rpm

Troubleshooting

The motor doesnt work: Verify: The wiring of the motor. The power supply of the motor (24 V). The compatibility of the control The heat generated (wait 5 minutes for the cooling of the motor). The equipment stops too soon: Verifiy: The operation of end-limits during the rotation of the motor. The crown is properly fitted to the tube. The end-limits of the motor are properly adjusted. Verify that the shade is within the recommended weight limit
SOMFY hereby declares that this product complies with the essential requirements and other relevant provisions of Directive 1999/5/EC. A Declaration of Conformity is available at the web address www.somfy.com/CE. Suitable for use in EU, CH and NO

Somfy worldwide

Argentina: Somfy Argentina Tel: +(0) 4737-3700 Australia: Somfy PTY LTD Tel: +61 (2) Fax: +61 (0) 0075 Austria: Somfy GesmbH Tel: +43 (0) 662 / 08 - 0 Fax: +43 (0) 662 / 08 - 22 Belgium: Somfy Belux Tel: +32 (0) Fax: +32 (0) Brasil: Somfy Brasil Ltda Osasco - SP - Brasil Tel/fax: +Canada: Somfy ULC Tel: +1 (0) 6446 Fax: +1 (0) 6448 China: Somfy China Co. Ltd Tel: +8621 (0) Fax: +8621 (0) Croatia : Somfy Predstavnitvo Tel: +385 (0) 640 Cyprus : Somfy Middle East Tel: +357(0) Fax: +357(0) Czech Republic: Somfy, spol. sr.o. Tel: (+420) 486-7 Fax: (+420) 846 Denmark: Somfy Nordic Danmark Tel: +93 Fax: +94 Export: Somfy Export Tel: + Tel: + Fax: + Finland: Somfy Nordic AB Finland Tel: +358 (0)Fax: +358 (0)France : Somfy France Tel. : +33 (0) 374 Fax : +33 (0) 074 Tel. : +33 (0) 055 Germany: Somfy GmbH Tel: +49 (0) 0 Fax: +49 (0) 9 (logistic) Greece: SOMFY HELLAS S.A. Tel: +6146768 Fax: +6120745 Hong Kong: Somfy Co. Ltd Tel: +852 (0) Fax: +852 (0) 2815 0716

Hungary : Somfy Kft Tel: +5120 Fax: +5121 India: Somfy India PVT Ltd Tel : +(91) 9176 Fax: +(91) 3080 Indonesia: Somfy Jakarta Tel: +(62) 3620 Fax: +(62) 7447 Iran: Somfy Iran Tel: +98-217-7951036 Fax : +98-217-7951036 Israel: Sisa Home Automation Ltd Tel: +972 (0) Italy: Somfy Italia s.r.l Tel: +39-024847181 Fax: +39-024455794 Japan: Somfy KK Tel: +81 (0)6800 Fax: +81 (0)6915 Jordan: Somfy Jordan Tel: +962-6-5821615 Kingdom of Saudi Arabia: Somfy Saoudi Riyadh : Tel/Fax: +020 Tel/Fax: +203 Jeddah : Tel: +353 Fax: +938 Kuwait: Somfy Kuwait Tel/Fax: +Lebanon:Somfy Lebanon Tel: +961 (0) 224 Fax: +961 (0) 228 Malaisia: Somfy Malaisia Tel: +60 (0) 74743 Mexico: Somfy Mexico SA de CV Tel: 52 (55) Fax: 52 (55) Morocco: Somfy Maroc Tel: +212-22443500 Fax: +212-22443523 Netherlands: Somfy BV Tel: +31 (0) Fax: +31 (0) Norway: Somfy Nordic Norge Tel: +39 Fax: +21 Poland: Somfy Sp. zo.o. Tel: +48 (22) 300 Fax: +48 (22) 301 Portugal: Somfy Portugal Tel. +Fax. +396 849
Romania: Somfy SRL Tel.: +40 - (0)368 - Fax: +40 - (0)368 - Russia: Somfy LLC Tel.: +72 Fax: +73 Serbia: SOMFY Predstavnitvo Tel: 00381 (0)510 Singapore: Somfy PTE Ltd Tel: +65 (0) Fax: +65 (0) Slovak republic: Somfy, spol. sr.o. Tel: +Tel: +Fax: +South Korea: Somfy JOO Tel: +82 (0) Fax: +82 (0) Spain: Somfy Espana SA Tel: +34 (0) 900 Fax: +34 (0) 396 Sweden: Somfy Nordic AB Tel: +46 (0) Fax: +46 (0) Switzerland: Somfy A.G. Tel: +41 (0) Fax: +41 (0) Syria: Somfy Syria Tel: +963-9-55580700 Tawan: Somfy Development and Taiwan Branch. Tel: +886 (0) 8934 Fax: +886 (0) 4680 Thailand:Bangkok Regional Office Tel: +66 (0) Tunisia: Somfy Tunisia Tel: +216-98303603 Turkey: Somfy TurkeyMah Tel: +90 (0) Fax: +90 (0) United Arab Emirates: Somfy Gulf Jebel Ali Free Zone Tel: +971 (0) Fax: +971 (0) United Kingdom: Somfy Limited Tel: +44 (0) 3030 Fax: +44 (0) 1133913010 United States: Somfy Systems Tel: +1 (0) 1300 Fax: +1 (0) 1776
Somfy SAS, capital 20.000.000 Euros,RCS Bonneville 303.970.230 11/2008