Cable holder (1)

Support belt (1) and screws (2)

Stand (1) and screws (4)

2: Attaching the stand

Packaging material

Take out the stand, screws, and packaging material to begin stand setup. Set the packaging material as shown. Place the TV directly to the stand as shown.
After placing the TV on the stand, remove the packaging material.
Fix the TV to the stand using the supplied screws.
This TV is very heavy, so two or more people should place the TV on the stand. If using an electric screwdriver, set the tightening torque at approximately 1.5 Nm (15 kgfcm).
3: Connecting an aerial/ VCR
Connecting an aerial only

Coaxial cable (supplied)

4: Preventing the TV from toppling over

Mains lead (supplied)

Connecting an aerial and VCR
Mains lead (supplied) Coaxial cable (supplied)

5: Bundling the cables

Scart lead (not supplied) Coaxial cable (not supplied)
6: Selecting the language and country/ region
Press F/f/G/g to select the language displayed on the menu screens, then press.
Press F/f to select the country/region in which you will operate the TV, then press.

3,4 3,2

Connect the TV to your mains socket (220240V AC, 50Hz). Press 1 on the TV (top side).
When you switch on the TV for the first time, the Language menu appears on the screen. When the TV is in standby mode (the 1 (standby) indicator on the TV (front) is red), press "/1 on the remote to switch on the TV. If the country/region in which you want to use the TV does not appear in the list, select - instead of a country/region. The message confirming the TV start auto-tuning appears on the screen, then go to 7: Auto-tuning the TV.

7: Auto-tuning the TV

The TV will now search for and store all available TV channels.

Press MENU to exit.

The TV has now tuned in all the available channels.
When a digital broadcast channel cannot be received, or when selecting a region in which there are no digital broadcasts in step 4 under 6: Selecting the language and country/region, the time must be set from Clock Set in the Set-up menu (page 29) after performing step 4.
Before you start auto-tuning the TV, insert a pre-recorded tape into the VCR connected to the TV (page 6) and start play back.
The video channel will be located and stored on the TV during auto-tuning. If no VCR is connected to the TV, this procedure is not required. Go to step 2.
Press G/g to select OK, then press
The TV starts searching for all available digital channels, followed by all available analogue channels. This may take some time, please be patient and do not press any buttons on the TV or remote. If a message appears for you to confirm the aerial connections No digital or analogue channels were found. Check all the aerial connections and press to start auto-tuning again.

When the Programme Sorting menu appears on the screen, follow the steps of Programme Sorting (page 32).
If you do not change the order in which the analogue channels are stored on the TV, go to step 4.

Safety information

Mains lead
Observe the followings to prevent the mains lead being damaged. If the mains lead is damaged, it may result in a fire or an electric shock. Unplug the mains lead when moving the TV set. When you disconnect the mains lead, disconnect it from the mains socket first. Be sure to grasp the plug when disconnecting the mains lead. Do not pull on the mains lead itself. Do not pinch, bend, or twist the mains lead excessively. The core conductors may be exposed or broken. Do not modify the mains lead. Do not put anything heavy on the mains lead. Keep the mains lead away from heat sources. If you damage the mains lead, stop using it and ask your dealer or Sony service centre to exchange it. Do not use the supplied mains lead on any other equipment. Use only an original Sony mains lead, not other brands.
The TV set is not disconnected from the mains when the TV set is switched off. To disconnect the TV set completely, pull the plug from the mains. However, some TV sets may have features which need the TV set to be left in standby to work correctly.

Carrying

Before carrying the TV set, disconnect all the cables from the TV set. Carrying the large size TV set requires two or more people. When you carry the TV set by hand, hold the TV set as illustrated on the right. When lifting the TV set or moving the panel of the TV set, hold it firmly from the bottom. If you do not do so, the TV set may fall and be damaged or cause serious injury. When transporting it, do not subject the TV set to jolts or excessive vibration. The TV set may fall and be damaged or cause serious injury. If the TV set has been dropped or damaged, have it checked immediately by qualified service personnel. When you carry the TV set in for repair or when you move it, pack it using the original carton and packing material.

Placement

The TV set should be installed near an easily accessible mains socket. Place the TV set on a stable, level surface. Do not hang anything on the TV set. If you do, the TV set may fall from the stand, causing damage or serious injury. Do not install the TV set in places subject to extreme temperature, for example in direct sunlight, or near a radiator, or heating vent. If the TV set is exposed to extreme temperature, the TV set may overheat and cause deformation of the casing or cause the TV set to malfunction. Do not install the TV set in a place exposed to direct air conditioning. If the TV set is installed in such a location, moisture may condense inside and may cause a malfunction. Never place the TV set in hot, oily, humid or excessively dusty places. Do not install the TV set where insects may enter. Do not install the TV set where it may be exposed to mechanical vibration. Do not install the TV set in a location where it may protrude, such as on or behind a pillar, or where you might bump your head on it. Otherwise, it may result in injury. Do not allow children to climb on the TV set. If you use the TV set near the seashore, salt may corrode metal parts of the TV set and cause internal damage or fire.

Do not place this TV set in a place where medical equipment is in use. It may cause a malfunction of medical instruments.
10 cm Leave at least this space around the set.

Outdoor use

Do not install this TV set outdoors. If the TV set is exposed to rain, it may result in a fire or an electric shock. If this TV set is exposed to direct sunlight, the TV set may heat up and it may damage the TV set.

Installed with stand

30 cm 10 cm 10 cm 6 cm
Vehicle, Ships and other vessels
Do not install this TV set in a vehicle. The motion of the vehicle may cause the TV set to fall down and cause injury. Do not install this TV set on a ship or other vessel. If the TV set is exposed to seawater, it may cause a fire or damage the TV set.
Leave at least this space around the set.
Never install the TV set as follows:
Air circulation is blocked.

Water and moisture

Do not use this TV set near water for example, near a bathtub or shower room. Also do not expose to rain, moisture or smoke. This may result in a fire or an electric shock. Do not touch the mains lead and the TV set with wet hands. Doing so may cause an electric shock or damage to the TV set.
Moisture and flammable objects
Do not place any objects on the TV set. The TV set shall not be exposed to dripping or splashing and that no objects filled with liquid, such as vases, shall be placed on the TV set. To prevent fire, keep flammable objects or naked lights (e.g. candles) away from the TV set. If any liquid or solid object does fall through openings in the cabinet, do not operate the TV set. It may result in an electric shock or damage to the TV set. Have it checked immediately by qualified service personnel.

Lightning storms

For your own safety, do not touch any part of the TV set, mains lead, or aerial lead during lightning storms.

Broken pieces

Do not throw anything at the TV set. The screen glass may break by the impact and cause serious injury. If the surface of the TV set cracks, do not touch it until you have unplugged the mains lead. Otherwise electric shock may result.

Servicing

Dangerously high voltages are present inside the TV set. Do not open the cabinet. Entrust the TV set to qualified service personnel only.
Small accessories removal and fittable
Keep small accessories out of childrens reach.

Precautions

Viewing the TV
To view the TV comfortably, the recommended viewing position is from four to seven times the screens vertical length away from the TV set. To obtain a clear picture, do not expose the screen to direct illumination or direct sunlight. If possible, use spot lighting directed down from the ceiling. View the TV in moderate light, as viewing the TV in poor light or during long period of time, strains your eyes.
Handling and cleaning the screen surface/cabinet of the TV set

Be sure to unplug the mains lead connected to the TV set from mains socket before cleaning. To avoid material degradation or screen coating degradation, observe the following precautions. Do not push on the screen, scratch it with a hard object, or throw anything at it. The screen may be damaged. Do not touch the display panel after operating the TV set continuously for a long period as the display panel becomes hot. We recommend that the screen surface be touched as little as possible. To remove dust from the screen surface/cabinet, wipe gently with a soft cloth. If dust is persistent, wipe with a soft cloth slightly moistened with a diluted mild detergent solution. Never use any type of abrasive pad, alkaline/acid cleaner, scouring powder, or volatile solvent, such as alcohol, benzene, thinner or insecticide. Using such materials or maintaining prolonged contact with rubber or vinyl materials may result in damage to the screen surface and cabinet material. The ventilation holes can accumulate dust over time. To ensure proper ventilation, we recommend removing the dust periodically (once a month) using a vacuum cleaner. If the angle of the TV set is to be adjusted, steady the base of the stand with your hand to prevent the TV set from becoming separated from the stand. Be careful not to get your fingers caught between the TV set and the stand.

Volume adjustment

Adjust the volume so as not to trouble your neighbours. Sound carries very easily at night time. Therefore, closing the windows or using headphones is suggested. When using headphones, adjust the volume so as to avoid excessive levels, as hearing damage may result.

LCD Screen

Although the LCD screen is made with high-precision technology and 99.99% or more of the pixels are effective, black dots may appear or bright points of light (red, blue, or green) may appear constantly on the LCD screen. This is a structural property of the LCD screen and is not a malfunction. Do not push or scratch the front filter, or place objects on top of this TV set. The image may be uneven or the LCD screen may be damaged. If this TV set is used in a cold place, a smear may occur in the picture or the picture may become dark. This does not indicate a failure. These phenomena disappear as the temperature rises. Ghosting may occur when still pictures are displayed continuously. It may disappear after a few moments. The screen and cabinet get warm when this TV set is in use. This is not a malfunction. The LCD screen contains a small amount of liquid crystal and mercury. The fluorescent tube used in this TV set also contains mercury. Follow your local ordinances and regulations for disposal.

Screen mode (page 16)
Changes the screen format when repeatedly pressed (displays the current screen format when pressed only once).

Input select / Text hold

In TV mode (page 21): Selects the input source from equipment connected to the TV sockets. In Analogue Text mode: Holds the current page. Tip
The A/B, PROG + and number 5 buttons have tactile dots. Use the tactile dots as references when operating the TV.
Overview of the TV buttons and indicators
(page 22) / Input select/OK
In TV mode (page 21): Selects the input source from equipment connected to the TV sockets. In TV menu: Selects the menu or option, and confirm the setting.
Increases (+) or decreases (-) the volume. In TV menu: Moves through the options left ( ) or right ( ).

4 PROG +/-/

In TV mode: Selects the next (+) or previous (-) channel. In TV menu: Moves through the options up ( ) or down ( ).
Switches the TV on or off.
6 Remote control sensor/Light sensor (page 29)
Receives IR signals from the remote. Do not put anything over the sensor, as its function may be affected.
Timer REC programme/Picture Off/ Timer indicator
Lights up in orange when the Timer recording is set (page 18, 19). Lights up in green when the picture is switched off (page 29). Lights up in orange when the timer is set (page 28).

Standby indicator

Lights up in red when the TV is in standby mode.

9 " Power indicator

Lights up in green when the TV is switched on.
Make sure that the TV is completely switched off before unplugging the mains lead. Unplugging the mains lead while the TV is turned on may cause the indicator to remain lit or may cause the TV to malfunction.
Press the number buttons or PROG +/- to select a TV channel.
To select channel numbers 10 and above using the number buttons, enter the second and third digits within two seconds. To select a digital channel using the Digital Electronic Programme Guide (EPG), see page 18. In digital mode An information banner appears briefly. The following icons may be indicated on the banner.
: : : : : : : Interactive service is available (Digital Text) Radio service Scrambled/Subscription service Multiple audio languages available Subtitles available Subtitles available for the hearing impaired Recommended minimum age for current programme (from 4 to 18 years) : Parental Lock : Current programme is being recorded

Additional operations

Do this

Press "/1.

Turn off the TV temporarily (Standby mode) Turn on the TV from Standby mode without sound Turn off the TV
Press %. Press 2 +/- to set the volume level. Press 1 on the TV (top side). Note
To disconnect the TV completely, pull the plug from the mains.

Adjust the volume

Press 1 on the TV (top side) to switch on the TV.
When the TV is in standby mode (the 1 (standby) indicator on the TV (front) is red), press "/1 on the remote to switch on the TV.
Press 2 + (increase)/ - (decrease). Press %. Press again to restore. Press. To select an analogue channel, press F/f, then press. To access the Input signal index table, see page 21.
Mute the sound Access the Programme index table (in analogue mode only)
Press DIGITAL to switch to digital mode or ANALOG to switch to analogue mode.
The channels available vary depending on the mode.

To access Digital Text

Many broadcasters provide a Digital Text service. Digital Text offers graphically rich contents, compared to Analogue Text. Select a digital channel which provides Digital Text, then press /. When a broadcaster provides a dedicated Digital Text channel, select this channel to access Digital Text. To navigate through Digital Text, follow the instructions on the screen. To exit Digital Text, press RETURN. To move around, press F/f/G/g. To select items, press and the number buttons. To access shortcuts, press the coloured buttons.

Smart*

Displays conventional 4:3 broadcasts with an imitation wide screen effect. The 4:3 picture is stretched to fill the screen. 4:3

To access Analogue Text

In analogue mode, press /. Each time you press /, the display changes cyclically as follows: Text t Text over the TV picture (mix mode) t No Text (exit the Text service) To select a page, press the number buttons or PROG +/-. To hold a page, press /. To reveal hidden information, press /.

Closes the Tools menu. See page 29. See page 36.
Digital Favourites (in See page 20. digital mode only) Picture Mode Sound Mode See page 23. See page 25.
Auto Clock Set (in Allows you to switch to digital analogue mode only) mode and obtain the time. Sleep Timer i Volume See page 28. Adjusts the volume of the headphones.
Checking the Digital Electronic Programme Guide (EPG) *
In digital mode, press to display the Digital Electronic Programme Guide (EPG). Perform the desired operation, as shown in the following table.
Note Digital Electronic Programme Guide (EPG)
* This function may not be available in some countries. Programme information will only be displayed if the TV station is transmitting it.
Turn off the EPG Move through the EPG Watch a current programme Sort the programme information by category Category list
Press. Press F/f/G/g. Press while the current programme is selected.
Press the blue button. Press F/f/G/g to select a category. The category name is displayed on the side.
The categories available include: All Categories: Contains all available channels. Category name (e.g. News): Contains all channels corresponding to the selected category.
The Digital Electronic Programme Guide (EPG) now only displays the current programmes from the category selected. Set a programme to be recorded Timer REC
Press F/f/G/g to select the future programme you want to record. Press. Press F/f to select Timer REC. Press to set the TV and your VCR timers.
A symbol appears by that programmes information. The indicator on the TV (front) lights up in orange. Notes
You can set VCR timer recording on the TV only for Smartlink compatible VCRs. If your VCR is not Smartlink compatible, a message will be displayed to remind you to set your VCR timer. Once a recording has begun, you can switch the TV to standby mode, but do not switch off the TV completely or the recording may be cancelled. If an age restriction for programmes has been selected, a message asking for pin code will appear on the screen. For more details refer to Parental Lock on page 36.
Set a programme to be displayed automatically on the screen when it starts Reminder
Do this Press F/f/G/g to select the future programme you want to display. Press. Press F/f to select Reminder. Press to automatically display the selected programme when the programme starts.
A c symbol appears by that programmes information. Note If you switch the TV to standby mode, it will automatically turn itself on when the programme is about to start. Set the time and date of a programme you want to record Manual timer REC
Press. Press F/f to select Manual timer REC, then press. Press F/f to select the date, then press g. Set the start and stop time in the same way as in step 3. Press F/f to select the programme, then press. Press to set the TV and your VCR timers.

Cancel a recording/reminder Timer list
Press. Press F/f to select Timer list, then press. Press F/f to select the programme you want to cancel, then press. Press F/f to select Cancel Timer, then press.
A display appears to confirm that you want to cancel the programme.
Press G/g to select Yes, then press

to confirm.

You can also display the Digital Electronic Programme Guide (EPG) by selecting Digital EPG in the MENU (page 22).

Using the Favourite list

The Favourite feature allows you to select programmes from a list of up to 20 channels you specify. To display the Favourite list, see Navigating through menus (page 22).

Favourite list

* This function may not be available in some countries.
Create your Favourite list for the first time
A message appears asking if you want to add channels to the Favourite list when you select Digital Favourites in the MENU for the first time.
Press to select Yes. Press F/f to select the channel you want to add.
If you know the channel number, you can use the number buttons to directly select a channel.
Channels that are stored in the Favourite list are indicated by a symbol. Turn off the Favourite list Watch a channel Add or remove channels in the Favourite list Press RETURN. Press while selecting a channel.

Press the blue button.

Channels that are stored in the Favourite list are indicated by a symbol.
Press F/f to select the channel you want to add or remove.
Remove all channels from the Favourite list 1
Press. Press the blue button to return to the Favourite list. Press the blue button. Press the yellow button.
A display appears to confirm that you want to delete all channels from the Favourite list.
Viewing pictures from connected equipment
Switch on the connected equipment, then perform one of the following operation.
For equipment connected to the scart sockets using a fully-wired 21-pin scart lead (page 38) Start playback on the connected equipment. The picture from the connected equipment appears on the screen. For an auto-tuned VCR (page 8) In analogue mode, press PROG +/-, or the number buttons, to select the video channel. For other connected equipment (page 37) Press / repeatedly until the correct input symbol (see below) appears on the screen. On screen display

Sound menu
You can select the options listed below on the Sound menu. To select options in Settings, refer to Picture menu (page 23).
Selects whether to apply settings made in the Sound menu to all inputs, or only to the input currently being watched. All: Applies settings to all inputs. Viewing Only: Applies settings only to the current input. Selects the sound mode. Dynamic: Enhances treble and bass. Standard: For standard sound. Recommended for home entertainment. Custom: Flat response. Also allows you to store your preferred settings. Resets the sound settings except Sound Mode, Dual Sound and i Speaker Link to the factory settings. Adjusts higher-pitched sounds. Adjusts lower-pitched sounds. Emphasizes left or right speaker balance. Keeps a constant volume level even when volume level gaps occur (e.g., adverts tend to be louder than programmes). Adjusts the volume level of the current input relative to other inputs, when Target Inputs is set to Viewing Only. Selects the surround mode. TruSurround XT: For surround sound (for stereo programmes only). Simulated Stereo: Adds a surround-like effect to mono programs. Off: For normal stereo or mono reception. Gives sound more impact by compensating for phase effects in speakers using the BBE High Definition Sound System.

Sound Mode

Reset Treble Bass Balance Auto Volume Volume Offset Surround

Dual Sound

Selects the sound from the speaker for a stereo or bilingual broadcast. Stereo, Mono: For a stereo broadcast. A/B/Mono: For a bilingual broadcast, select A for sound channel 1, B for sound channel 2, or Mono for a mono channel, if available.
If you select other equipment connected to the TV, set Dual Sound to Stereo, A or B.
i Speaker Link (headphone speaker link)
Switches the TVs internal speakers on/off when headphones are connected. On: Sound is output only from headphones. Off: Sound is output from both the TV and headphones.
Treble, Bass, Balance, Auto Volume, Surround and BBE cannot be used for headphones and audio output sockets.

Screen menu

You can select the options listed below on the Screen menu. To select options in Settings, refer to Picture menu (page 23).

Selects whether to apply settings made in the Screen menu to all inputs, or only to the input currently being watched. All: Applies settings to all inputs. Viewing Only: Applies settings only to the current input. For details about the screen format, see To change the screen format manually to suit the broadcast (page 16). Automatically changes the screen format according to the broadcast signal. To keep your setting, select Off.
Even if you have selected On or Off in Auto Format, you can always modify the format of the screen by pressing repeatedly. Auto Format is available for PAL and SECAM signals only.
Screen Format Auto Format

4:3 Default

Selects the default screen format for use with 4:3 broadcasts. Smart: Displays conventional 4:3 broadcasts with an imitation wide screen effect. 4:3: Displays conventional 4:3 broadcasts in the correct proportions. Off: Keeps the current Screen Format setting when the channel or input is changed.
This option is available only if Auto Format is set to On.

Display Area

Adjusts the screen area displaying the picture. Full Pixel: Displays the picture for 1080i or 1080p sources in the original size when parts of the picture are cut off. Normal: Displays the picture in the original size. 1/2: Enlarges the picture to hide the edge of the picture. Adjusts the horizontal position of the picture. Adjusts the vertical position of the picture when the screen format is set to Smart (50 Hz), Zoom or 14:9. Adjusts the vertical size of the picture when the screen format is set to Smart, Zoom or 14:9.
Horizontal Shift Vertical Shift Vertical Size

Set-up menu

You can select the options listed below on the Set-up menu. To select options in Settings, refer to Picture menu (page 23).

Auto Start-up

Starts the first time operation menu to select the language and country/region, and tune in all available digital and analogue channels. Usually, you do not need to do this operation because the language and country/region will have been selected and channels already tuned when the TV was first installed (page 7, 8). However, this option allows you to repeat the process (e.g., to retune the TV after moving house, or to search for new channels that have been launched by broadcasters). Selects the language in which the menus are displayed. Assigns a name to any equipment connected to the side and rear sockets. The name will be displayed briefly on the screen when the equipment is selected. You can skip an input source that is not necessary. 1 Press F/f to select the desired input source, then press. 2 Press F/f to select the desired option below, then press.

Quiet Power On Speaker

Audio Out
Colour System Product Information

All Reset

Resets all settings to the factory settings and then displays the Auto Start-up screen.
All settings, including Digital Favourite list, country, language, auto tuned channels, etc. will be reset.

PC Settings menu

You can select the options listed below on the PC Settings menu. To select options in Settings, refer to Picture menu (page 23).

Screen Format

Selects a screen format for displaying input from your PC. Normal: Displays the picture in its original size. Full1: Enlarges the picture to fill the display area, keeping its original horizontalto-vertical aspect ratio. Full2: Enlarges the picture to fill the display area. Resets the PC settings except Screen Format and Power Management to the factory settings. Automatically adjusts the display position and phase of the picture when the TV receives an input signal from the connected PC.
Auto Adjustment may not work well with certain input signals. In such cases, manually adjust Phase, Pitch, Horizontal Shift and Vertical Shift.

Reset Auto Adjustment

Phase Pitch Horizontal Shift Vertical Shift Power Management
Adjusts the phase when the screen flickers. Adjusts the pitch when the picture has unwanted vertical stripes. Adjusts the horizontal position of the picture. Adjusts the vertical position of the picture. Switches the TV to standby mode if no signal is received for 30 seconds.
Analogue Set-up menu (Analogue mode only)
You can change/set the analogue settings using the Analogue Set-up menu. To select options in Settings, refer to Picture menu (page 23).

1 Digit Direct

When 1 Digit Direct is set to On, you can select an analogue channel using one preset number button (0 - 9) on the remote.
When 1 Digit Direct is set to On, you cannot select channel numbers 10 and above entering two digits using the remote.

Auto Tuning

Press the number buttons to enter the three-digit programme number of the broadcast you want.
Remove or change the order of the digital channels as follows: To remove the digital channel
Press. A message that confirms whether the selected digital channel is to be. deleted appears. Press G to select Yes, then press
To change the order of the digital channels
Press g, then press F/f to select the new position for the channel and press G. Repeat the procedure in steps 1 and 2 to move other channels if required.

Press RETURN.

Digital Manual Tuning Tunes the digital channels manually. 1 Press the number button to select the channel number you want to manually tune, then press F/f to tune the channel. 2 When the available channels are found, press F/f to select the channel you want to store, then press. 3 Press F/f to select the programme number where you want to store the new channel, then press. Repeat the procedure above to tune other channels manually.

Digital Set-up

Displays the Digital Set-up menu. Subtitle Setting* Displays digital subtitles on the screen. When For Hard Of Hearing is selected, some visual aids may also be displayed with the subtitles (if TV channels broadcast such information). Subtitle Language* Selects which language subtitles are displayed in. Audio Language* Selects the language used for a programme. Some digital channels may broadcast several audio languages for a programme. Audio Type* Increases the sound level when For Hard Of Hearing is selected. Parental Lock* Sets an age restriction for programmes. Any programme that exceeds the age restriction can only be watched after a PIN Code is entered correctly. 1 Press the number buttons to enter your existing PIN code.
If you have not previously set a PIN, a PIN code entry screen appears. Follow the instruction of PIN Code below.
Press F/f to select the age restriction or None (for unrestricted watching), then press. Press RETURN.
PIN Code* Sets a PIN code for the first time, or allows you to change your PIN code. 1 Enter a PIN as follows: If you have previously set a PIN
Press the number buttons to enter your existing PIN.
If you have not set a PIN
Press the number buttons to enter the factory setting PIN of 9999.
Press the number buttons to enter the new PIN code.
A message appears to inform you that the new PIN has been accepted.
PIN code 9999 is always accepted.
Technical Set-up Displays the Technical Set-up menu. Auto Service Update: Enables the TV to detect and store new digital services as they become available. Software Download: Enables the TV to automatically receive software updates, free through your existing aerial (when issued). Sony recommends that this option is set to On at all times. If you do not want your software to be updated, set this option to Off. System Information: Displays the current software version and the signal level. Time Zone: Allows you to manually select the time zone you are in, if it is not the same as the default time zone setting for your country. CA Module Set-up Allows you to access a Pay Per View service once you obtain a Conditional Access Module (CAM) and a view card. See page 37 for the location of the (PCMCIA) socket.

Digital channel is not displayed

General

The TV turns off automatically (the TV enters standby mode)
Cause/Remedy Check if the Sleep Timer is activated, or confirm the Duration setting of On Timer (page 28). If no signal is received and no operation is performed in the TV mode for 10 minutes, the TV automatically switches to standby mode. Check if the On Timer is activated (page 29). Select AV Preset in the Set-up menu and cancel Skip of the input source (page 28). Replace the batteries.
The TV turns on automatically Some input sources cannot be selected The remote does not function

Numerics

1 Digit Direct 32 14:4:3 Default 27 4:3 16
Digital Auto Tuning 35 Digital Manual Tuning 35 Digital Set-up 36 Digital Set-up menu 35 Digital Text 16 Digital Tuning 35 Display Area 27 Display Mode 23 Dual Sound 26
Parental Lock 36 PC Settings menu 31 Phase 31 Picture menu 23 Picture Mode 23 Picture Off ( ) indicator 14 PIN Code 36 Pitch 31 Power (") indicator 14 Power (1) switch 14 Power Management 31 Power Saving 29 Product Information 29 Programme index table 15 Programme Labels 32 Programme List Edit 35 Programme Sorting 32
Adv. Contrast Enhancer 24 Advanced Settings 24 Aerial, connecting 6 AFT 33 All Reset 30 Analogue Set-up menu 32 Analogue Text 16 Audio Filter 33 Audio Language 36 Audio Out 29 Audio Type 36 Auto Adjustment 31 Auto Clock Set 17, 21, 39 Auto Format 27 Auto S Video 28 Auto Start-up 28 Auto Tuning analogue and digital channels 8 analogue channels only 32 digital channels only 35 Auto Volume 25 AV Preset 28 AV2 Output 29
EPG (Digital Electronic Programme Guide) 18 Equipment labels 28
Fastext 16 Favourite list 20

Gamma 24

Quiet Power On 29
Headphones connecting 37 Speaker Link 26 Volume 17, 21, 39 Horizontal Shift 27, 31 Hue 23
Reminder 19 Remote control inserting batteries 4 overview 13 sensor 14 Reset PC settings 31 picture 23 sound 25
Input signal index table 21 Interactive service 15

Classic Serviceparts are pleased to announce the development of three new replacement remote controls to cover the Sony Bravia range of LCD TVs.
IRC81801 IRC81818 IRC81819
Sony Part RM-ED001 RM-ED002 RM-ED005 RM-ED007 RM-ED008 RM-ED009 RM-ED011 RM-ED011W RM-ED013 RM-ED014 Sony Model KDL-15G2000 KDL-19L4000 KDL-20B4030 KDL-20B4050 KDL-20G2000 KDL-20G3000 KDL-20G3030 KDL-20S2000 KDL-20S2020 KDL-20S2030 KDL-20S3000 KDL-20S3020 KDL-20S3030 KDL-20S3040 KDL-20S3050 KDL-20S3060 KDL-20S3070 Classic Remote IRC81801 IRC81801 IRC81818 IRC81818 IRC81818 IRC81818 IRC81819 IRC81819 IRC81819 IRC81819 Classic Remote IRC81818 IRC81819 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 Sony Model KDL-20S4000 KDL-20S4020 KDL-23B4030 KDL-23B4050 KDL-25P2530 KDL-26B4030 KDL-26B4050 KDL-26E4000 KDL-26E4020 KDL-26E4030 KDL-26E4050 KDL-26L4000 KDL-26P2520 KDL-26P2530 KDL-26P3000 KDL-26P300H KDL-26P3020 KDL-26P302H KDL-26P3030 KDL-26S2000 KDL-26S2010 KDL-26S2020 KDL-26S2030 KDL-26S2800 KDL-26S2810 KDL-26S2820 KDL-26S3000 KDL-26S3010 KDL-26S3020 Classic Remote IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81819 IRC81819 IRC81819 IRC81819 IRC81819 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818

Phone: 01759 303068

Fax: 01759 303620
Online: chsinteractive.co.uk
Sony Model KDL-26S4000 KDL-26S4010 KDL-26T2600 KDL-26T260H KDL-26T2800 KDL-26T3000 KDL-26U2000 KDL-26U2500 KDL-26U2520 KDL-26U2530 KDL-26U3000 KDL-26U3020 KDL-26U4000 KDL-26V4000 KDL-26V4220 KDL-26V4230 KDL-26V4240 KDL-26V4500 KDL-32D2600 KDL-32D2710 KDL-32D2810 KDL-32D3000 KDL-32D3010 KDL-32E4000 KDL-32E4020 KDL-32E4030 KDL-32E4050 KDL-32L4000 KDL-32P2520 KDL-32P2530 KDL-32P3000 KDL-32P300H KDL-32P3020 KDL-32P302H KDL-32P3030 KDL-32P5500 KDL-32S2000 KDL-32S2010
Classic Remote IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81819 IRC81818 IRC81818 IRC81818 IRC81819 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81819 IRC81819 IRC81819 IRC81819 IRC81819 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818
Sony Model KDL-32S2020 KDL-32S2030 KDL-32S2510 KDL-32S2520 KDL-32S2530 KDL-32S2800 KDL-32S2810 KDL-32S2820 KDL-32S3000 KDL-32S3010 KDL-32S3020 KDL-32S4000 KDL-32S4010 KDL-32T2600 KDL-32T2800 KDL-32T3000 KDL-32U2000 KDL-32U2500 KDL-32U2510 KDL-32U2520 KDL-32U2530 KDL-32U3000 KDL-32U3020 KDL-32U4000 KDL-32V2000 KDL-32V2500 KDL-32V4000 KDL-32V4200 KDL-32V4210 KDL-32V4220 KDL-32V4230 KDL-32V4240 KDL-32V4500 KDL-32V4710 KDL-32V4720 KDL-32V4730 KDL-32W4000 KDL-32W4210
Classic Remote IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81818 IRC81819 IRC81819 IRC81819 IRC81819 IRC81819 IRC81819
Sony Model KDL-32W4220 KDL-32W4230 KDL-37P3000 KDL-37P300H KDL-37P3020 KDL-37P302H KDL-37P3030 KDL-37S4000 KDL-37S4010 KDL-37U3000 KDL-37U3020 KDL-37U4000 KDL-37V4000 KDL-37V4220 KDL-37V4230 KDL-37V4240 KDL-37V4500 KDL-37V4710 KDL-40D2600 KDL-40D2710 KDL-40D2810 KDL-40D3000 KDL-40D3010 KDL-40D3400 KDL-40D3500 KDL-40D3550 KDL-40D3660 KDL-40E4000 KDL-40E4020 KDL-40E4030 KDL-40E4050 KDL-40L4000 KDL-40P2520 KDL-40P2530 KDL-40P3000 KDL-40P300H KDL-40P3020 KDL-40P302H