3-859-844-13(1)

Camera Adaptor

Operating Instructions

Before operating the unit, please read this manual thoroughly and retain it for future reference.

CA-TX7/TX7P

1997 by Sony Corporation

WARNING

To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.
For the customers in the USA This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. This device requires shielded interface cables to comply with FCC emission limits.
This symbol is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

Table of Contents

Overview... 4 Location and Function of Parts.. 5 Front and Left Side.. 5 Switches and Knobs on the Rear and Right Side. 7 Connectors on the Rear and Right Side.. 9 Mounting on Video Camera.. 11 Notes on Use.. 14 Specifications... 15

Overview

The CA-TX7/TX7P Camera Adaptor, which is docked with a DXC-D30/ D30P or DXC-637 series Color Video Camera, allows connecting the camera to the CCU-TX7/TX7P Camera Control Unit via a triaxial cable.
Component signal transfer method

AAAAyA<H.L0.idx>

This unit enables transfer of Y, RY and BY signals for high picture quality.

Long-distance transfer

The maximum triaxial cable length that can be used to connect this unit to a camera control unit is max. 750 m (when using a Belden 8.5 mm cable) or 1125 m (when using a Belden 13.2 mm cable).
Electrical shock prevention function
To prevent electrical shock, this unit shuts off any high-voltage power supply whenever there is an incomplete connection.

Coaxial cable connection

When necessary, this unit can be connected to a camera control unit via a coaxial cable.1)
Variety of input/output connectors
Input/output connectors for the following signals are provided: Video signal output for teleprompter Return video signal output Intercom/program output for connected headset Microphone or line-in audio input Lens or tripod head control signal output
....... 1) This units triaxial connector must be refitted to enable connection of a coaxial cable. Consult your Sony dealer for details.
Location and Function of Parts

Front and Left Side

Accessory shoe
2 TALK switch 3 INTERCOM switch 4 INTERCOM knob 5 PROGRAM knob
Shoulder strap fitting 6 RETURN 1/RETURN 2 buttons

1 Camera connector

7 BREAKER button 8 POWER switch
1 Camera connector (PRO 76-pin DIGITAL or PRO 50-pin) Connects to the cameras VTR connector. Two types of connectors are provided and can be replaced according to the camera. PRO 76-pin DIGITAL: Use this connector for docking with the DXC-D30/D30P digital video cameras. PRO 50-pin: Use this connector for docking with the DXC-637 series analog video cameras.

For details on replacing these connectors, see Mounting on video Camera on page 11.
3 INTERCOM switch Selects the channel for transferring intercom audio. CH1: Selects CH1 (channel 1). CH2: Selects CH2 (channel 2).
When the LINE switch on the CCU-TX7/TX7P Camera Control Unit is in the PRIV position, the intercom operates only between the camera and the camera control unit regardless of the INTERCOM switch position. 4 INTERCOM knob Adjusts the intercom audio reception level. When using a DXC-D30/D30P, setting the TALK switch 2 to REMOTE will enable the audio level knob on the DXC-D30/D30Ps front panel to adjust both the intercom audio and program audio levels. 5 PROGRAM knob Adjusts the program audio reception level. When using a DXC-D30/D30P camera, setting the TALK switch 2 to REMOTE will enable this knob to adjust the balance between the program audio and intercom audio levels. Turn clockwise to raise the program audio level, and turn counterclockwise to raise the intercom audio level.
Use a DXC-D30/D30P with ROM of ver. 1.1 or later. For version check and ROM change, consult your Sony dealer. 2 TALK switch Selects whether or not to transfer intercom audio from the camera to the camera control unit. ON: Transfers intercom audio from camera to camera control unit. OFF: Do not transfer intercom audio from camera to camera control unit. REMOTE: Transfers intercom audio from camera to camera control unit only while the VTR START button on camera or lens is being pressed.
6 RETURN 1/RETURN 2 buttons Select the return video signal1) to be output from the RETURN OUT connector and to the cameras viewfinder. Press the RETURN 1 or RETURN 2 button to select the return video signal 1 or return video signal 2 from the camera control unit. To show the shooting picture on the viewfinder screen, release the button. The return video signal which selected last is still output from the RETURN OUT connector if the button is released. 7 BREAKER button The power to this unit is cut off when the circuit breaker is activated by a power source or connection problem. After resolving the problem, press this button to reset the breaker.
If the breaker gets activated even after correcting the connection, contact your Sony dealer.
8 POWER switch Turns this units power supply on and off. To power the unit, set the switch to EXT or CCU according to the type of power source being used.

EXT Power supplied via an optional CMA-8A/8ACE AC Adaptor connected to the DC IN connector (when this unit is connected to a camera control unit via a coaxial cable)
CCU Power supplied via camera control unit (when this unit is connected to a camera control unit via a triaxial cable)
Set this to OFF to turn off the power supply. When this unit is connected to a camera control unit via a triaxial cable, the following functions continue to operate even after the power is turned off. Intercom communication On/off control of the back tally indicator (when TALLY switch is ON) Calling via CALL button
....... 1) Return video: Video signals that are sent from a camera to a camera control unit and returned to the same or another camera so that the camera operators can check the recorded image.
Switches and Knobs on the Rear and Right Side
1 Cursor knobs 2 TALLY switch 3 Back tally indicator 4 CALL button 7 UHF portable tuner taps
5 AUDIO SELECT (CH1/CH2) switches 6 MIC IN +48V (CH1/CH2) switch

8 CURSOR switch

Illustration: CA-TX7
1 Cursor knobs (for DXC-D30/D30P) When the CURSOR switch 8 is set to A or B, this adjusts the position and size of the box cursor that is displayed in the viewfinder of the DXC-D30/D30P. H-POSITION: Adjusts the horizontal position of the box cursor. V-POSITION: Adjusts the vertical position of the box cursor. WIDTH: Adjusts the width of the box cursor. HEIGHT: Adjusts the height of the box cursor. 2 TALLY switch Set this switch to the ON position to activate the back tally indicator 3. 3 Back tally indicator (red) When the TALLY switch 2 is in the ON position, this indicator lights (in red) in response to this units operating status. It also lights when the CALL button on the camera control unit or remote control panel has been pressed.
4 CALL button Press this button to call the operator of the camera control unit or remote control panel. Pressing this button lights the tally indicator (red) on the camera control unit, on the remote control panel, and in the cameras viewfinder. This units back tally indicator 3 also lights if the TALLY switch 2 is in the ON position. 5 AUDIO SELECT (CH1/CH2) switches Select the source for signals to be transferred via the camera control units channel 1 and channel 2. CAMERA: Transfers audio from a microphone on the camera to the camera control unit. CA-MIC: Transfers audio from a microphone connected to this units MIC IN (CH1/CH2) connector to the camera control unit. CA-LINE: Transfers audio from a line output connected to this units MIC IN (CH1/CH2) connector to the camera control unit.
6 MIC IN +48V (CH1/CH2) switch Selects whether or not to supply power to a microphone connected via the MIC IN CH1 and CH2 connectors. ON: Supplys +48-V power to microphone. OFF: Do not supply power to microphone. Leave this switch in the ON position when using a microphone of phantom powering1) type. 7 UHF portable tuner taps When using an optional WRR-810A UHF Portable Tuner, attach the holder and bracket (supplied with the WRR-810A) for the portable tuner mounting adapter.

For details of attaching and using the WRR-810A, see the Operating Instructions for the WRR-810A.
8 CURSOR switch (for DXC-D30/D30P) Selects whether or not to display a box cursor in the DXC-D30/D30P Color Video Cameras viewfinder. B: Displays box cursor B. A: Displays box cursor A. OFF: No box cursor is displayed.
No cursor is displayed in the viewfinder when using a DXC-637 series camera.
....... 1) Phantom powering: Powering method for operating condenser microphones by supplying power via a bias power source and an amplifier. Because no DC voltage is present in the audio channel, it is called phantom powering.
Connectors on the Rear and Right Side
5 CCU connector 1 INTERCOM/PROGRAM connector 2 PROMPTER OUT connector 6 DATA connector

3 RETURN OUT connector

7 DC OUT connector 8 DC IN connector
4 MIC IN (CH1/CH2) connectors Illustration: CA-TX7
1 INTERCOM/PROGRAM connector (XLR 5-pin, male) Connect a headset for monitoring intercom audio or program audio. Normally, a monaural (one-side) headset should be connected. An internal adjustment can be made to enable both sides of the headset to receive audio, with intercom audio on the left side and program audio on the right side.
Contact your Sony dealer for further information on this internal adjustment.
Contact your Sony dealer for further information on the internal adjustment to change the teleprompter video signal transfer direction.
3 RETURN OUT (return video signal output) connector (BNC type) Outputs return video signals from a camera control unit. Use the RETURN 1 and RETURN 2 buttons to switch between the two return video signals. 4 MIC IN (CH1/CH2) (MIC inputs, channel 1 and channel 2) connectors (XLR 3-pin, female) Connect external microphones or other equipment as sources for audio to be transferred to the camera control units channel 1 or 2. Set the AUDIO SELECT (CH1/CH2) switch to select the channel for the connected equipment.
2 PROMPTER OUT (teleprompter video signal output) connector (BNC type) Outputs teleprompter video signals1) from the camera control unit. (This unit can treat color teleprompter video signals.) If you have made the internal adjustment to change the teleprompter video signal transfer direction so that signals are transferred from this unit to the camera control unit, this connector becomes the input connector for teleprompter video signals.
....... 1) Teleprompter video signals: Video signals for prompter which displays scripts in the television monitor by the camera lens or on the face of a one-way mirror positioned directly in front of the camera lens so that performers can read scripts while looking into the camera lens.
5 CCU (Camera control unit) connector (CATX7: Kings triaxial connector, CA-TX7P: Fischer triaxial connector) Connect a camera control unit via a triaxial cable. In addition to supporting signal transmission between this unit and the connected camera control unit, the triaxial cable enables this unit to receive its power supply via the camera control unit. Using a coaxial cable to connect the camera control unit The CCU connector must be refitted to enable connection of a coaxial cable. Note that connecting a coaxial cable makes it impossible for this unit to receive power from the camera control unit. Use a CMA-8A/8ACE AC Adaptor for AC power sources.

Contact your Sony dealer for more information on refitting the CCU connector.
6 DATA connector (10-pin) Outputs control signals for the lens (focus or zoom control) and the tripod head (panning or tilting) that are sent from a remote control panel connected to the camera control unit.
For further information about using this connector, consult your Sony dealer.
7 DC OUT connector (4-pin) Use this connector when supplying power (DC 12V, Max. 12 W) to a WRR-810A UHF Portable Tuner (supplied separately) or an LCD teleprompter unit.
Never connect a unit that has a power consumption rating of more than 12 W. 8 DC IN connector (XLR 4-pin) When connecting this unit to a camera control unit via a coaxial cable, use this connector for a CMA-8A/ 8ACE AC Adaptor (supplied separately). Use the CCQX-3 DC power cord to connect the CMA-8A/ 8ACE to this unit.

Mounting on Video Camera

This unit is dockable with the DXC-D30/D30P digital video camera or with a DXC-637 series analog video camera. Replace the camera connector according to the camera to be used. Using a DXC-D30/D30P : Use the PRO 76-pin DIGITAL connector. Using a DXC-637 series camera : Use the PRO 50-pin connector.
Turn the POWER switch off before mounting the unit on the camera.

Using the DXC-D30/D30P

Replace the PRO 50-pin connector with the PRO 76-pin DIGITAL connector.
Loosen the two screws (M3) and remove the cover from the PRO 50-pin connector.
Never loosen the other screws.

PRO 50-pin connector

Press the right side of the PRO 50-pin connector until the PRO 76-pin DIGITAL connector appears. The both connectors swing to switch the positions by pressing either of them.
PRO 76-pin DIGITAL connector

(Continued)

Attach the cover upside down. Make sure that the match mark lines up with PRO 76P DIGITAL indication.

Match mark

PRO76P DIGITAL
Using the DXC-637 series camera
Replace the PRO 76-pin DIGITAL connector with the PRO 50-pin connector. Press the left side of the PRO 76-pin DIGITAL connector until the PRO 50-pin connector appears. Make sure that the match mark lines up with PRO 50P indication.

Mounting on the camera

This section describes the procedure for mounting this unit on a DXCD30/D30P. Use the same procedure for mounting on a DXC-637 series camera. (Replace the PRO 76-pin DIGITAL connector with the PRO 50pin connector.)
If necessary, replace the PRO 50-pin connector with the PRO 76-pin DIGITAL connector.
For details, see Using the DXCD30/D30P (page 11).
Fit the projection on the bottom of this unit into the slot on the camera.
Camera Slot Groove Projection
Slide the unit along the groove on the camera, and press firmly until fixed.
Tighten the two screws (M4 12) in the figure.

Mscrews

Tighten the two screws (M4 6) to fix the shoulder pad.

Slide the shoulder pad to its central position before tightening the screws. Otherwise the screws may not be properly fixed.

Removing from the camera

Follow the procedure above in reverse.

Notes on Use

Use and storage locations Avoid using or storing the unit in the following places: Where it is subject to extremes of temperature (operating temperature: 10C to +45C (14F to 113F)). Note that in summer the temperature in a car with the windows closed can reach 50C (122F). Very damp or dusty places. Where rain is likely to reach the unit. Places subject to severe vibration. Near strong magnetic fields Near transmitting stations generating strong radio waves. Avoid violent impacts Dropping the unit, or otherwise imparting a violent shock to it, is likely to cause it to malfunction. Do not cover with cloth While the unit is in operation, do not cover it with a cloth or other material. This can cause the temperature to rise, leading to a malfunction. After use Turn the POWER switches on the unit and camera control unit off. Care
If the body of the unit is dirty, wipe it with a dry cloth. For severe dirt, use a soft cloth steeped in a small amount of neutral detergent, then wipe dry. Do not use volatile solvents such as alcohol or thinners, as these may damage the finish.

Specifications

General
Power requirements When supplied via the CCU connector: 120 V AC When supplied via the DC IN connector: 12 V DC (10.5 to 17 V DC) Power consumption Varies according to connected equipment as shown in the following tables1):
When power is supplied via the CCU connector Power consumption CA-TX7/TX7P CA-TX7/TX7P and connected equipment CA-TX7/TX7P CA-TX7/TX7P+DXCD30/D30P CA-TX7/TX7P+DXCD30/D30P+DXF-701/ 701CE CA-TX7/TX7P+DXCD30/D30P+DXF-51/ 51CE CA-TX7/TX7P outputting 12 W from the DC OUT connector+DXC-D30/ D30P+DXF-51/51CE 10.5 W 11 W 11.2 W 23.7 W 26 W When power is supplied via the DC IN connector Power consumption CA-TX7/TX7P CA-TX7/TX7P and connected equipment CA-TX7/TX7P CA-TX7/TX7P+DXCD30/D30P CA-TX7/TX7P+DXCD30/D30P+DXF-701/ 701CE CA-TX7/TX7P+DXCD30/D30P+DXF-51/ 51CE CA-TX7/TX7P outputting 12 W from the DC OUT connector+DXC-D30/ D30P+DXF-51/51CE 7.5 W 7.5 W 7.5 W 20.2 W 22.3 W

30.2 W

42.2 W

12.3 W

13.3 W
Operating temperature 10C to +45C (14F to 113F) Operating humidity 20% to 90% Storage temperature 20C to +60C (4F to 140F) Mass Approx. 2.7 kg (5 lb 15 oz) External dimensions 131 mm (3/1 /4 inches) (w/h/d)
....... 1) The power consumption indicated on the name plate of the unit is total consumption of the CA-TX7/TX7P outputting 12 W from the DC OUT connector, DXCD30/D30P, and DXF-51/51CE.

Input/output connectors

CCU CA-TX7: Kings triaxial connector (made by Lemo) CA-TX7P: Fischer triaxial connector
BNC, 1.0 Vp-p, 75 RETURN OUT BNC, 1.0 Vp-p, 75 INTERCOM/PROGRAM XLR 5-pin Input level: 60 dBs (dynamic) Output level: to +12 dBs MIC IN 1,2 XLR 3-pin, female, 600 , balanced Input level: 60 dB (for microphone input) or 20 dB (for line input) DC IN XLR 4-pin, 10.5 to 17 V DC DC OUT 4-pin, 10.5 to 17 V DC, max. 12 W DATA 10-pin Analog: 0 to 5 V DC 4 Digital: 0 or 5 V DC 2 Camera connector PRO 76-pin DIGITAL or PRO 50pin

PROMPTER OUT

Accessories supplied
Operating instructions (1)

Accessories not supplied

Triaxial cable (Belden) CCQX-3 DC Power Cord CMA-8A/8ACE AC Adaptor WRR-810A UHF Portable Tuner
Design and specifications are subject to change without notice.

Sony Corporation

Printed in Japan

Camera Control Unit

CCU-TX7
he Sony CCU-TX7 is a compact camera control unit designed to be the core unit of the Sony triax camera control system for the
DXC-D30/D30WS and the DXC-637 video cameras. The CCU-TX7 system has several functions designed for operational convenience and system versatility, in addition to the inherent benefits of the triax system itself such as, camera control over great distances and small lightweight cables. he CCU-TX7 can run on either AC or DC (12 volts) at the discretion of the operator. This compact unit (half of a 19-inch rack mount), provides a variety of video output signals: SDI,
composite, Y/C, component, and R/G/B. The CCU-TX7 also supports a teleprompter system and major intercom systems such as 2-wire, 4-wire, Clearcom and RTS. To meet the demands of various situations, the CCU-TX7 also has two inputs for return video and a teleprompter input.
upporting the CCU-TX7 are the COU-TX7 Camera Operation Unit, the RCP-TX7 Remote Control Panel, and the CA-TX7
Camera Adaptor. By combining these peripheral products, the best triax camera control system can be easily set up for each application. Also, this control system allows quick camera set-up and one-person camera operation for managing multiple cameras.
ith all these features and efficiencies, the CCU-TX7 is sure to broaden the range of applications of these two cameras, and
create new opportunities for video professionals.

MAIN FEATURES

High Quality Triax Transmission
The CCU-TX7 system uses analog component video transmission, which has a 9MHz bandwidth for the luminance (Y) signal and 4.5MHz for the color difference signals (R-Y/B-Y).
quality digital signals with just one cable to SDI ready units. Using SDI interface, a total digital DXC system becomes a reality.
Note* The CCU-TX7 (Serial No. less than 11000) needs some modification to accommodate the SDI outputs. Please contact your nearest Sony office.
Two Inputs for Return Video
The CCU-TX7 has two RETURN VIDEO inputs (BNC type), thus accepting return video signals (VBS color) from two different systems. At the CA-TX7/TX7P end, two channels of return video can be selected.
Long Distance Transmission
The maximum cable length is 1500m via 14.5mm triax cable (with return video) (Fujikura), up to 1125m via 13.2mm cable (Mohawk, Belden) and up to 750m via 8.5mm cable (Fujikura, Mohawk, Belden). A teleprompter video channel can also be transmitted through the same cable.

Other Signal Outputs

The CCU-TX7 provides two composite outputs, and two component output selectable from Y/R-Y/B-Y, R/G/B and Y/C. The CCU-TX7 also has a 4-pin WF MODE (waveform monitor mode) connector for flickerless parade monitoring of signals, in addition to a WF output and a PIX (picture monitor) output.
Color Teleprompter Compatible
The CCU-TX7 system can be used with color teleprompter systems. Since reverse signal transmission (CA -> CCU) is supported using a teleprompter video channel in a triax cable, it is also possible to transmit video signals other than those for teleprompter from CA to CCU, if necessary.
* For detailed information, please contact your nearest Sony office.
High Speed High Quality Serial Data Transmission
A maximum of 10-bit quantized data can be transmitted at high speed via serial data transmission using a triax cable. This achieves the benefits of smooth and real-time control and instant tactile response from remote control devices.

AC/DC Operation

The CCU-TX7 is designed to operate not only on AC power but also DC power. The CCU-TX7 has a DC inlet for DC 12V (10.5V to 17V) as well as an AC inlet. DC operation greatly expands the system flexibility in field production truck applications.

Digital Signal Outputs

The CCU-TX7 provides two SDI outputs when the optional DXBK-701 SDI Output Board is installed. It can transfer high

Flexible Intercom System

The CCU-TX7 has a program audio channel and a bi-directional intercom channel. Program audio sound from an external audio system can be fed to the camera head, being mixed with the intercom. Major intercom systems (Fourwire/Two-wire/RTS/Clearcom) can be interfaced via respective connectors on the rear panel of the CCU-TX7. The CCU-TX7 system can accept twochannel input from an external intercom system. Communication can be easily routed to the selected counterpart from either the CA-TX7 end, CCU-TX7 end, or the external intercom system (CH-1 or CH-2).
Program Microphone System
The CCU-TX7 and the CA-TX7 are equipped with a two-channel microphone system. Two XLR connectors on the CATX7 provide balanced audio CH-1 and CH-2 inputs with microphone phantom power available for an external microphone. The MIC input gain of each channel can be controlled within a range of 12dB in 16 steps by rotary switches on the internal board of the CCU-TX7.
Coaxial Control Capability
The CCU-TX7 is equipped with a coaxial input. This enables the camera to be controlled via conventional coaxial cable instead of a triax cable, with power supplied locally to the camera.

Compact Size

The CCU-TX7 is half a 19-inch rack size wide and 4 units high. With the RMMTXC7 Rack Mount Kit, 2 units of the CCU-TX7 or one unit with a waveform monitor can be mounted into the standard 19-inch rack.

RS-232C port

The CCU-TX7 is equipped with an RS232C port to link multiple CCU-TX7 units for a multiple camera control operation, or to connect an external personal computer.
DXBK-701 SDI Output Board

PERIPHERALS

CA-TX7

Rotary Triax Connector

The CA-TX7 Triax Camera Adaptor is equipped with a rotary (70) triax connector for easy cabling.
Viewfinder Box Cursor Indication
The CA-TX7 is capable of indicating a box cursor on the screen of any viewfinder of the DXC-D30/D30WS such as the DXF-701WS, and DXF-51. Cursor position (H, V) and size (width, height) can be respectively controlled with control volumes on the rear panel of the CA-TX7. Two kinds of cursors can be stored and retrieved.

* This function is not available for the DXC-637.

76-pin/50-pin Interface

The CA-TX7 is equipped with both Pro 76-pin Digital and Pro 50-pin interfaces, which makes it docked with the DXC-D30/D30WS and the DXC-637.

Pro 50-pin

Pro 76-pin Digital

RCP-TX7

As A Remote Control Panel
q Full Camera Control The RCP-TX7 offers full control functions as a remote camera control panel for the CCU-TX7, covering basic camera control up to more sophisticated operations. It controls camera set-up using convenient scene files, as well as basic control and paint operation controls. For engineering and service purposes, the RCP-TX7 also has a more comprehensive camera setup function. The RCP-TX7 is one forth the width of a 19-inch rack. A total of 4 units of the RCP-TX7 can be installed into the standard 19-inch rack with the RMM-TXR7 Rack Mount Kit. q Scene File System The RCP-TX7 can store up to 16 scene files. All parameters both for camera operation and set-up can be adjusted and stored in each scene file. The stored scene file most suitable for a particular shooting situation can be instantly recalled. q Links in Control of Iris and Master Black In a multi-camera system, linkage control of Iris and Master Black can be set for multiple RCP-TX7 panels. To set the linkage, press the IRIS/M.BLACK LINK button of each RCP-TX7 that you want to link. In controlling Iris and Master Black, the same value can be overridden to all the linked RCP-TX7 units from one RCPTX7, and either one of them can be the initiator at anytime. q Color Matching Capability The RCP-TX7 has a convenient color matching function. When using multiple cameras and RCP-TX7 units, once you finish setting up one RCP-TX7, you can copy the master data to the other RCPTX7 units. Before starting, it is necessary to set one RCP-TX7 as a master and the others as subsidiary units.

COU-TX7

q Convenient Liquid Crystal Display The RCP-TX7 has an LCD (Liquid Crystal Display) on the control panel. The LCD shows menu status information on the item being adjusted. Function status such as Detail Level, Gamma, Knee, White Balance and Black (Flare) Balance can also be displayed on the LCD by using an INDICATION button. The LCD also displays troubleshooting hints, when an operational difficulty arises from use of the RCP-TX7 controls.
As Standalone Camera Controller
When directly connected to the DXC-D30/ D30WS through a 10-pin remote connector, the RCP-TX7 can be used as a standalone remote control unit just like the RM-M7G. (This function is available only for the DXC-D30/ D30WS.)
Basic Camera Control with COU-TX7
The COU-TX7 can be attached as a part of the front panel of the CCU-TX7. Basic control of camera operations can be done with the COU-TX7. This is useful when using the CCU-TX7 in limited space, such as in field production vehicles.

SYSTEM CONFIGURATION

DXF-51(5-inch)) Monochrome Viewfinder Intercom (System & Headset)
WRR-810A + DC-WL800(DC Pack Unit) Wireless Microphone Receiver DXF-701WS(*) or DXF-601 Viewfinder DXC-D30/D30WS or DXC-637 Camera Head CA-TX7 Camera Adaptor Triax Cable
CCU-TX7 Camera Control Unit
Waveform Monitor Vectorscope

Zoom Lens

Picture Monitor SDI Output (w/DXBK-701)
* DXF-701WS can be used only with DXC-D30/D30WS.
CCA-7 (10-pin/10-pin) (Max.50m) Intercom (Headset)
AC DC 12V COU-TX7 Camera Operation Unit
RCP-TX7 Remote Control Panel
Either the COU-TX7 or the RCP-TX7 is used as a control panel of the CCU-TX7.

SPECIFICATIONS

1. CCU-TX7
Input connectors GEN LOCK:

RETURN VIDEO (1,2):

2. CA-TX7
BNC type, loopthrough, VBS/BS, 1.0Vp-p, 75ohms BNC type, loopthrough, VBS, 1.0 Vp-p, 75ohms BNC type, loopthrough, VBS, 1.0 Vp-p, 75ohms BNC type, VBS, 1.0 Vp-p, 75ohms BNC type, Y: 1.0Vp-p, 75ohms R-Y/B-Y: 700mVp-p, 75ohms BNC type, 700mVp-p, 75ohms BNC type, Y: 1.0Vp-p, 75ohms C: NTSC:286mVp-p, 75ohms PAL:300mVp-p, 75ohms Conform to serial digital interface (270Mbps), 0.8 Vp-p, 75 BNC type, VBS, 0.3 Vp-p, 75ohms, negative BNC type, 1.0 Vp-p, 75ohms BNC type, 714mVp-p, 75ohms (Encoded output: 1.0 Vp-p, 75ohms) XLR 3-pin, 0dBu/-20dBu balanced, 2 channels Triax (Kings type) x 1 BNC type x 1 10-pin D-sub 25-pin x 1 4W/2W TALLY: 24V DC, TTL level or contact signals switchable XLR 5-pin x 1 XLR 3-pin x 1 XLR 3-pin x 1 D-sub 25-pin x 2 Input/output connectors Triax (Kings type) x 1 Pro 76P Digital or Pro 50P switchable CAMERA INTERFACE: XLR 3-pin x 2, 600ohms, balanced MIC IN (CH-1/2) Input level : Mic in:-60dB : Line in: -20dB DC IN: XLR 4-pin x 1,10.5V to 17V DC OUT: 4-pin x 1, 10.5V to 17V, Max 12W PROMPTER OUT: BNC type x 1, 1.0Vp-p, 75ohms RETURN OUT: BNC type x 1, 1.0Vp-p, 75ohms INTERCOM/PROGRAM: XLR 5-pin x 1 (for Headset) Input level: -60dBs (dynamic) Output level: to 12dBs DATA OUT: 10-pin x 1 DC 0 to 5V (analog) x 4 DC 0 or 5V (digital) x 2 DC 120V (from Triax connector) or DC 12V (10.5 to 17.0V) (from DC IN connector) DC 120V DC 12V (Supplied from triax connector) (Supplied from DC IN connector)
CA-TX7 internal only CA-TX7 only w/DXC-D30, DXF-701/CE w/DXC-D30, DXF-51 10.5W 11.2W 12.3W Total 10.5W 26W 35W CA-TX7 internal only 7.5W 7.5W 7.5W Total 7.5W 22.3W 30.2W
PROMPT VIDEO (prompter): Output connectors VBS (1,2) (BNC): (*1)Y/R-Y/B-Y (1,2):
(*1)R/G/B (1,2): (*1)Y/C (1,2):
(*2)SDI (1,2): SYNC: PIX (picture monitor): WF (waveform monitor):
Power requirements Power consumption
MIC OUT (CH-1/2): Camera control input/output connectors Camera: Coax: REMOTE: INTERCOM/TALLY:

Operating temperature Storage temperature Operating humidity Weight Dimensions (W x H x D) Supplied accessory
-10C to 45C (14F to 113F) -20C to 55C (-4F to 131F) 20% to 90% Approx. 2.7 kg (5 lb 15oz) 226 x 221 x 131mm (9 x 8 3/4 x 5 1/4 inches) Operation manual x 1
INTERCOM (Front) PGM IN RTS RS232C Power requirements AC 120V or DC 10.5 to 17.0V Power consumption 95W max. Cable length 1500m max. (14.5mm) Operating temperature 5C to 40C (41F to 104F) Storage temperature -20C to 55C (-4F to 131F) Weight Approx. 8.45 kg (18 lb 10oz) Dimensions (W x H x D) 218 x 169 x 415mm (8 5/8 x 6 3/4 x 16 3/8 inches) Supplied accessories AC power cord x 1 Plug holder for AC power cord x 1 Number plate (1 set) Operation manual x 1

3. RCP-TX7

Power requirements Power consumption Operating temperature Storage temperature Weight Dimensions (W x H x D) Cable length Supplied accessory 10 to 17V (supplied from camera or CCU) 4.0W -10C to 45C (14F to 113F) -20C to 55C (-4F to 131F) Approx. 1.5kg (3 lb 5 oz) 100 x 330 x 70mm (4 x 13 x 2 7/8 inches) 50m max. (with CCA-7 cable) CCA-7-5 Connecting Cable (5m) Number plate (1set) Screws and washers x2 Operation manual x 1

300 (11 7/8) 330 (13)

316 (12 1/2) 261.2 (10 3/8) 22.14 42.7
(*)Note: 1) These CCU output signals can be selected to be R/G/B or Y/R-Y/B-Y or Y/C. 2) Using optional DXBK-701 (SDI Output Board)

105 (4 1/4) 80 (3 1/4)

4. COU-TX7

155 (6 1/8) 146 (5 3/4)

163 (6 1/2) CCU-TXCA-TX7
Weight Dimensions (W x H x D) Supplied accessory
Approx. 330g (12.6 oz) 105 x 155 x 43mm (4 1/4 x 6 1/8 x 1 3/4 inches) Operation manual x 1

221 (8 3/4)

370 (14 5/8) 280 (11 1/8)

5. RMM-TXC7

380 (15)

230 (9 1/8) 370 (14 5/8)

Approx. 3.7 kg (8 lb 3 oz) 482 x 177 x 380mm (19 1/8 x 7 x 15 inches) Installation manual x 1

220 (8 3/4)

23.(7) 436 (17 1/4)

164 (6 1/2) (4 7/8)

482 (19)

6. RMM-TXR7

354 (14) 10 29
Weight Dimensions (W x H x D) 140 (5 5/8) 200 (7 7/8) 9.5 (3/8) Supplied accessory
Approx. 2.7 kg (5 lb 12 oz) 482 x 75 x 354mm (19 x 3 x 14 inches) Installation manual x 1
404 (16) 424 (16 3/4) 482 (19)
1999 Sony Corporation. All rights reserved. Reproduction in whole or in part without Sonys written permission is prohibited. Features and specifications are subject to change without notice. Sony is a trademark of Sony Corporation. The Quality Management systems in design of the CCU-TX7, CA-TX7, RCP-TX7, COU-TX7, RMM-TXC7 and RMM-TXR7 have been assessed and registered as meeting the requirements of ISO 9001.

7. DXBK-701

Power Consumption Weight Dimensions (W x H x D) 4.5 W 330 g (11.6 oz) 17 x 148 x 277 mm (11/16 x 5 7/8 x 11 inches)

Distributed by

MK4125V2OHB99MAR
Printed in Japan 1999 Sony Corporation