3-810-585-23 (1)

Operating Instructions

EN F ES S C
CDP-CE505 CDP-CE405 CDP-CE305 CDP-C450Z CDP-C350Z CDP-C250Z CDP-C661

1995 by Sony Corporation

WARNING
To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

On power sources

Before operating the player, check that the operating voltage of the player is identical with your local power supply. The operating voltage is indicated on the nameplate at the rear of the player. The player is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the player itself has been turned off. If you are not going to use the player for a long time, be sure to disconnect the player from the wall outlet. To disconnect the AC power cord (mains lead), grasp the plug itself; never pull the cord. AC power cord must be changed only at the qualified service shop.

CAUTION

You are cautioned that any changes or modification not expressly approved in this manual could void your authority to operate this equipment.

Owners Record

The model and serial numbers are located at the rear of the unit. Record the serial number in the space provided below. Refer to them whenever you call upon your Sony dealer regarding this product. This symbol is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Model No. _________________________ Serial No. _________________________

On placement

Place the player in a location with adequate ventilation to prevent heat build-up in the player. Do not place the player on a soft surface such as a rug that might block the ventilation holes on the bottom. Do not place the player in a location near heat sources, or in a place subject to direct sunlight, excessive dust or mechanical shock.
For the customers in Australia
The following caution label is located inside the unit.

On operation

If the player is brought directly from a cold to a warm location, or is placed in a very damp room, moisture may condense on the lenses inside the player. Should this occur, the player may not operate properly. In this case, remove the disc and leave the player turned on for about an hour until the moisture evaporates.

INFORMATION

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior.

On adjusting volume

Do not turn up the volume while listening to a portion with very low level inputs or no audio signals. If you do, the speakers may be damaged when a peak level portion is played.

On cleaning

Clean the cabinet, panel and controls with a soft cloth slightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder or solvent such as alcohol or benzine.

Precautions

On safety
Caution The use of optical instruments with this product will increase eye hazard. Should any solid object or liquid fall into the cabinet, unplug the player and have it checked by qualified personnel before operating it any further.
If you have any questions or problems concerning your player, please consult your nearest Sony dealer.

Getting Started

Welcome!
Thank you for purchasing the Sony Compact Disc Player. Before operating the unit, please read this manual thoroughly and retain it for future reference.

TABLE OF CONTENTS

Unpacking.... 4 Hooking Up the System... 4

About This Manual

The instructions in this manual are for models CDP-CE505, CDP-CE405, CDPCE305, CDP-C450Z. CDP-C350Z, CDPC250Z and CDP-C661. The CDP-CE505 is the model used for illustration purposes, unless otherwise mentioned. Any difference in operation is clearly indicated in the text, for example, CDPCE505 only.

Playing a CD.... 6

Playing CDs
Using the Display... 8 Replacing Discs While Playing a Disc.. 8 Locating a Specific Disc... 9 Locating a Specific Track or a Particular Point in a Track. 9 Playing Tracks Repeatedly... 10 Playing in Random Order (Shuffle Play).. 10 Creating Your Own Program (Program Play).. 11

Conventions

Instructions in this manual describe the controls on the player. You can also use the controls on the remote if they have the same or similar names as those on the player. The following icons are used in this manual: Indicates that you can do the task using the remote. (Note that the CDP-CE305, CDP-C250Z and CDP-C661 cannot do the tasks marked with this icon.) Indicates hints and tips for making the task easier.

Recording From CDs

Recording Your Own Program.. 13 Recording a CD by Specifying Tape Length (Time Edit) (except for CDP-C450Z, CDP-C350Z and CDP-C250Z). 13 Fading In or Out.... 14 Adjusting the Recording Level (Peak Search) (except for CDP-C450Z, CDP-C350Z and CDP-C250Z). 15

Storing Information About CDs (Custom Files) (CDP-CE505 and CDP-C450Z only)
What You Can Do With the Custm Files... 16 Grouping Tracks (Music Clip)... 16 Storing Specific Tracks (Delete Bank)... 17

Additional Information

Notes on CDs.... 18 Troubleshooting.... 19 Specifications.... 19

Index... Backcover

Unpacking
Check that you received the following items: Audio connecting cord (1) Remote commander (remote) (except for CDPCE305, CDP-C250Z and CDP-C661) (1) Sony SUM-3 (NS) batteries (except for CDP-CE305, CDP-C250Z and CDP-C661) (2)

Hooking Up the System

Overview
This section describes how to hook up the CD player to an amplifier. Be sure to turn off the power of each component before making the connections.

CD player

Inserting batteries into the remote (except for CDP-CE305, CDP-C250Z and CDP-C661)
You can control the player using the supplied remote. Insert two R6 (size AA) batteries by matching the + and on the batteries. When using the remote, point it at the remote sensor g on the player.
Line output (R) Line output (L) To an AC outlet

Audio input (L)

Audio input (R)

Amplifier

When to replace batteries
With normal use, the batteries should last for about six months. When the remote no longer operates the player, replace all the batteries with new ones. : Signal flow To an AC outlet

What cords will I need?

Audio cord (supplied) (1)
Do not leave the remote near an extremely hot or humid place. Do not drop any foreign object into the remote casing, particularly when replacing the batteries. Do not expose the remote sensor to direct sunlight or lighting apparatuses. Doing so may cause a malfunction. If you dont use the remote for an extended period of time, remove the batteries to avoid possible damage from battery leakage and corrosion.

White (L) Red (R)

Hookups
When connecting an audio cord, be sure to match the color-coded cord to the appropriate jacks on the components: Red (right) to Red and White (left) to White. Be sure to make connections firmly to avoid hum and noise.

CD player Amplifier

If you have a component with the CONTROL A1 connector (CDP-CE505 only)
Connect the component via the CONTROL A1 connector. You can control the player with the connected component. For details, refer to the supplementary instructions.
Connecting the AC power cord
Connect the AC power cord to a wall outlet.

The player plays

All discs in the player consecutively in the order of disc number Only the disc youve selected
You can select the disc you want to start playing first Press one of the DISC 15 buttons. When listening with the headphones (CDP-CE505 and CDP-C450Z only) Connect the headphones to the PHONES jack on the player and adjust the volume with the PHONE LEVEL control on the player or with the LINE OUT LEVEL +/ buttons on the remote. You can adjust the output level to the amplifier (except for CDP-CE305, CDP-C250Z and CDP-C661) Press LINE OUT LEVEL +/ on the remote. You can reduce the output level up to 20 dB. When you reduce the output level, FADE appears in the display. When you turn off the player, the output level automatically returns to the maximum level. Note If you press the LINE OUT LEVEL +/ buttons on the remote while recording, the recording level will change even when it is preset on the tape deck, etc. (except for CDP-CE305, CDP-C250Z and CDP-C661).
Press. The disc tray closes and the player plays all the tracks once (Continuous Play). Adjust the volume on the amplifier.

To stop playback

Press p.

DISC 15 / P p

DISC SKIP

OPEN/CLOSE

Pause Resume play after pause Go to the next track Go back to the preceding track Go to the next disc Select a disc directly Stop play and remove the CD
P P or DISC SKIP DISC 15 OPEN/CLOSE

Using the Display

You can check information about the disc using the display.
Checking the remaining time
Each time you press TIME while playing a disc, the display changes as shown in the chart below.
Playing time and number of the current track

ALL DISCS

Press TIME. Remaining time on the current track
Checking the total number and playing time of the tracks
Press TIME before you start playing. The display shows the current disc number, the total number of tracks, total playing time and music calendar.

Current disc number

If the track number exceeds 24, . appears instead of the remaining time.
Press TIME. Remaining time on the disc

Total playing time

This information is available only in Continuous Play mode. Total number of tracks Music calendar Press TIME.
The information also appears when you press OPEN/CLOSE to close the disc tray. The tracks numbered over 20 cannot be displayed in the music calendar. Notes on the disc number indications

To cancel Repeat Play

Press REPEAT repeatedly until REPEAT disappears from the display.
Repeating the current track
You can repeat only the current track while the disc is played in Continuous Play. While the track you want is being played, press REPEAT repeatedly until REPEAT 1 appears in the display.
When you directly locate a track numbered over 10
Press >10 first, then the corresponding number buttons. To enter 0, use button 10. Example: To play track number 30 Press >10 first, then 3 and 10.
You can extend the playing time during Music Scan
Press MUSIC SCAN repeatedly until the playing time you want (10, 20 or 30) appears in the display. (For CDPCE505 or CDP-C450Z, press M. SCAN on the remote.) Each time you press the button, the playing time changes cyclically.
Playing in Random Order (Shuffle Play)
You can have the player shuffle tracks and play in a random order. The player shuffles all the tracks on all discs or on the disc youve specified.

SHUFFLE DISC

If appears in the display, the disc has reached the end while you were pressing ). Press 0 or to go back.
Playing Tracks Repeatedly
You can play discs/tracks repeatedly in any play mode.

REPEAT

Shuffle Play on all discs
You can play all tracks on all discs in a random order.
Press REPEAT while playing a disc. REPEAT appears in the display. The player repeats the discs/tracks as follows:
Press SHUFFLE repeatedly until ALL DISCS appears in the display. Press to start ALL DISCS Shuffle Play. The indication appears while the player is shuffling the tracks.

To cancel Shuffle Play

Press CONTINUE.
You can start Shuffle Play while playing
Press SHUFFLE, and Shuffle Play starts from the current track.
Creating Your Own Program (Program Play)
You can arrange the order of the tracks on the discs and create your own program. The program can contain up to 32 tracks.

PROGRAM CHECK CLEAR p

You can specify discs during Shuffle Play (Select Shuffle Play)
You can specify discs during ALL DISCS Shuffle Play mode, and the tracks on the specified discs are played in a random order. Press DISC to specify the discs after Step 1. Semi-circles appear around the specified disc numbers in the display. To cancel the selected discs, press DISC again. The semi-circles disappear. To return to ALL DISCS Shuffle Play, press SHUFFLE twice.

Shuffle Play on one disc

You can play all tracks on the specific disc in a random order.

DISC 1 5

Press SHUFFLE repeatedly until 1 DISC appears in the display. Press DISC to start 1 DISC Shuffle Play on the selected disc. The indication appears while the player is shuffling the tracks.
Press PROGRAM. PROGRAM appears in the display. If a program is already stored, the last step of the program appears in the display. When you want to erase the whole program, hold down CLEAR until ALL CLr appears in the display (see page 12). Press DISC to select the disc.

PROGRAM DISC

AL in the display stands for all tracks. When you want to program the whole disc as one step, skip Step 3 and go to Step 4.
Press the number buttons of the tracks you want to program in the order you want. To program the track numbered over 10, use the >10 button (see page 10).

Last programmed track

Playing order

After one second

Programmed tracks

If youve made a mistake

Press CLEAR, then press the correct number button.

(Continued)

To program other discs or tracks, do the following: To program
Other discs Other tracks on the same disc Other tracks on other discs

Checking the track order

You can check your program before or after you start playing. Press CHECK. Each time you press this button, the display shows the track (the disc and track numbers) or the disc (the disc number and AL indication) of each step in the programmed order. After the last step in the program, the display shows End and returns to the original display. If you check the order after you start playing, the display shows only the remaining steps.

Repeat Step(s)

2 and 3
Press to start Program Play.

To cancel Program Play

You can create your program while checking the disc labels

To check and change your program
See page 12. A The indication appears while checking the program B for side A and while checking the program for side B.
When you record on side B, reverse the tape and press or P on the player to resume playing.

Fading In or Out

You can manually fade in or out to prevent tracks from starting or ending abruptly. Note that you cannot use this effect when you use the DIGITAL OUT (OPTICAL) connector.

To cancel Time Edit

You can program the tracks you want in advance
Select the tracks before doing the above procedure. The player creates a program from the remaining tracks.
You can freely specify the tape length
Set the tape length using number buttons. To enter 0, use button 10. Example: When the tape length of one side is 30 minutes and 15 seconds Press 3, 10, 1 and 5.

FADER**

Number buttons EDIT/TIME FADE*
*except for CDP-C450Z, CDP-C350Z and CDP-C250Z **except for CDP-CE505 and CDP-C450Z (CDP-CE505 and CDP-C450Z only)
You can check and change the program

See page 12.

When track numbers flash in Step 3 or 4 (CDP-CE505 only)
This means that there is a portion remaining on the tape after the player has programmed all the tracks so that you can add more tracks to the portion (Link Edit). You can also select another disc and add the tracks on the disc you select if the tracks on the current disc are shorter than the remaining time. Press EDIT/TIME FADE to have the player add the tracks, or press number buttons of the tracks flashing in the display. When you want to add tracks on another disc, press DISC SKIP to select the disc, and then press number buttons of the track. After adding the tracks, press to start playing. If you dont need to add tracks, just press to start playing. When B in the

Start play fading in

Press FADER
During pause. FADE lights up in the display and the Q indication flashes. The play fades in. When you want to start fading out. FADE lights up in the display and the q indication flashes. The play fades out and the player pauses.

End play fading out

indication flashes
This means that more than 1 minute remains on the tape but no track on the current disc fits the remaining portion. If you add tracks on other discs, select the disc you want and follow the procedure above.
Fading lasts for about 5 seconds. However, when you press FADER during Music Scan (see page 10), the play fades out for about 2 seconds.
Changing the fading time (CDP-CE505 and CDP-C450Z only)
You can change the fading time from 2 to 10 seconds before fading in or out. If you dont change it, fading lasts for 5 seconds.
Press FADER on the remote before you start playing.
Press the number button corresponding to the fading time you want (210).
Fading out at the specified time (Time Fade) (except for CDP-C450Z, CDP-C350Z and CDP-C250Z)
You can have the player fade out automatically by specifying the playing time. Once you set the Time Fade, it works twice, that is, the play fades out at the end of both sides of a tape.
Adjusting the Recording Level (Peak Search) (except for CDP-C450Z, CDPC350Z and CDP-C250Z)
The player locates the highest level among the tracks to be recorded to let you adjust the recording level before you start recording.

PEAK SEARCH p

Press EDIT/TIME FADE repeatedly before you start playing until and A in the indication appear in the display.

TIME FADE

Press or to specify the playing time. Each time you press these buttons, the display changes as shown below, with the playing time of one side following each indication.
Before you start playing, press PEAK SEARCH. PEAK flashes in the display and the player repeats the portion of the highest level. Adjust the recording level on the deck. Press p on the player to stop Peak Search. PEAK disappears from the display.
Press to start playing. At the specified time the play fades out and the player pauses. B in the indication appears in the display.
The portion with the highest level may differ every time you try the adjustment on the same disc. The difference is, however, so slight that you wont find any problem in adjusting the recording level precisely. Peak Search does not operate while you open the disc tray by pressing EX-CHANGE.
To record on side B, reverse the tape and press or P on the player to resume playing. Again, the play fades out at the specified time.

To cancel Time Fade

Press EDIT/TIME FADE.
You can freely specify the playing time
See You can freexly specify the tape length on page 14.
You can change discs during Time Fade
If the play ends before the specified fade-out time, (for example, when you record CD-singles on a tape) change the disc. The specified fade-out time is counted only during playing.

You can fade in to resume playing in Step 4
After you reverse the tape, press FADER.
If you press 0 or ) during Time Fade, Time Fade will be cancelled.
What You Can Do With the Custom Files
The player can store 2 types of information called Custom Files for each disc. Once you have stored Custom Files for a disc, the player automatically recalls what you have stored whenever you select the disc. Note that Custom Files will be erased if you dont use the player for about 1 month.

Erasing Custom Files

If the memory for Custom Files becomes full, the player displays FULL when you press FILE to store the information and you cannot store any more disc information. If necessary, erase any unwanted Custom Files as follows: To erase all Custom Files of one disc
If the disc you want to clear is stored in the Music Clip, remove all the tracks of the disc from the clip following the procedure in Remove tracks from a clip on page 17. If the disc you want to clear is stored in the Delete Bank, erase all the Delete Bank following the procedure in Erasing the Delete Bank on page 18.
You can store this information:

When you use

Music Clip (page 16) Delete Bank (page 17)

You can

Group the tracks on each disc into up to 4 groups Delete unwanted tracks and store only the tracks you want
To erase all Custom Files of all discs
While holding down ERASE and 1 on the player, press POWER to turn off and on the player. ALL ErS appears in the display and all the Custom Files will be erased.
The Custom File indication lights up when you store the corresponding information.
Grouping Tracks (Music Clip)
You can group the track on each disc into up to 4 groups called clips. Once you store a track into a clip, you can use the Music Clip every time you play the disc. You can also play only the tracks stored in a selected clip. You can store one track into four clips, or all tracks on a disc into one clip. Note that tracks numbered over 32 cannot be stored into a clip.

FILE DELETE CLIP A B C D

Where are Custom Files stored?

Delete Bank

Music Clip
Custom Files are stored not on the disc but in the players memory. This means you cannot use Custom Files when you play the disc on other players.
How many discs can you file?
You can file up to 172 discs in the Custom File.

MUSIC CLIP buttons

Storing tracks into clips 1 Play the track you want to store into a clip. 2
Press one of the MUSIC CLIP buttons (A, B, C or D). C-FILE appears and the selected MUSIC CLIP button flashes for a while. Repeat Steps 1 and 2 to store other tracks into clips.
Storing Information About CDs (Custom Files) (CDP-CE505 only) Storing Information About CDs (Custom Files) (CDP-CE505 and CDP-C450Z only) Recording From CDs
Playing tracks in a clip (Clip Play)
Press one of the MUSIC CLIP buttons before you start playing. C-PLAY appears in the display and the selected MUSIC CLIP button lights. The tracks stored in the clip appear in the music calendar. The player starts playing tracks in the selected clip. To play tracks in another clip
Press p to stop playing, then press one of the MUSIC CLIP buttons you want to play.
Storing Specific Tracks (Delete Bank)
You can delete unwanted tracks and store only the tracks you want. When you select the disc with the Delete Bank, you can play only the tracks you want. The player memorizes the Delete Bank for about 1 month, even if you turn off the player.

CONTINUE SHUFFLE

Clip Play is available only in Continuous and Shuffle Play mode. If you press MUSIC CLIP in Program Play mode, the player automatically enters Continuous Play mode and starts Clip Play. In ALL DISCS Play mode, the player plays the tracks in the selected clip on all discs consecutively. If you press MUSIC CLIP during Clip Play, the button does not operate.

ERASE Number buttons

Insert or select the disc. Press SHUFFLE to select ALL DISCS or 1 DISC. Press the number buttons to delete the tracks you want to delete. The track number and OFF appears in the display and the track numbers youve deleted disappear from the music calendar. If youve made a mistake
Press the number button of the track. The track number and On appears in the display and the track will be restored.
Removing tracks from a clip 1 Before you start playing, press one of the MUSIC
CLIP buttons to start Clip Play.
Press or to select the track you want to remove from the clip. Press ERASE to remove the track. ErASE appears in the display for a while. The player starts playing the next track in the clip. Repeat Steps 2 and 3 to remove other tracks. When youve removed all tracks from the clip, the MUSIC CLIP button goes off after the player plays the last track in the clip.

Press FILE to store the remaining tracks. FILE and DELETE in the Custom File indication light up in the display. You can delete unwanted tracks during playback
Press CLEAR while playing the track. The player starts playing the next track. If you press FILE, the player stores the remaining tracks.
Storing Information About CDs (Custom Files) (CDP-CE505/C450Z only)
Playing using the Delete Bank 1
Insert or select the disc. FILE and DELETE in the Custom File indication light up in the display. Press CONTINUE or SHUFFLE to select ALL DISCS or 1 DISC. Press or one of the DISC15 buttons you want to start playing.

Notes on CDs

On handling CDs
To keep the disc clean, handle the disc by its edge. Do not touch the surface. Do not stick paper or tape on the disc.
Erasing the Delete Bank 1 Insert or select the disc.
FILE and DELETE in the Custom File indication light up in the display.
Not this way Do not expose the disc to direct sunlight or heat sources such as hot air ducts, nor leave it in a car parked in direct sunlight as there can be considerable rise in temperature inside the car. Do not use any commercially available stabilizer. If you do, the disc and the player may be damaged. After playing, store the disc in its case.
Press FILE. FILE appears in the display. Press ERASE while FILE appears in the display. The Delete Bank is erased. ErASE apperas in the display and FILE and DELETE in the Custom File indication disappear.
Before playing, clean the disc with a cleaning cloth. Wipe the disc from the center out.
Do not use solvents such as benzine, thinner, commercially available cleaners or anti-static spray intended for vinyl LPs.

Troubleshooting

If you experience any of the following difficulties while using the player, use this troubleshooting guide to help you remedy the problem. Should any problem persist, consult your nearest Sony dealer. Theres no sound. /Check that the player is connected securely. /Make sure you operate the amplifier correctly. /Adjust the playback level using the PHONE LEVEL control on the player (CDP-CE505 and CDP-C450Z only) or LINE OUT LEVEL +/ on the remote (except for CDP-CE305, CDP-C250Z and CDP-C661). The CD does not play. /Theres no CD inside the player (no DISC appears). Insert a CD. /Place the CD with the label side up on the disc tray correctly. /Clean the CD (see page 18). /Moisture has condensed inside the player. Remove the disc and leave the player turned on for about an hour (see page 2). The remote does not function. (except for CDP-CE305, CDP-C250Z and CDP-C661) /Remove the obstacles in the path of the remote and the player. /Point the remote at the remote sensor g on the player. /Replace all the batteries in the remote with new ones if they are weak. The player functions incorrectly. /The microcomputer chips may be operating incorrectly. Turn the power off, then turn it back on to reset the player.

Specifications

Compact disc player
Laser Semiconductor laser ( = 780 nm) Emission duration: continuous Max 44.6 W* * This output is the value measured at a distance of 200 mm from the objective lens surface on the Optical Pick-up block with 7 mm aperture. 2 Hz to 20 kHz 0.5 dB CDP-CE505/C450Z: More than 107 dB CDP-CE405/CE305/C350Z/C250Z /C661: More than 102 dB More than 98 dB CDP-CE505/C450Z: Less than 0.0035% CDP-CE405/CE305/C350Z/C250Z /C661: Less than 0.0045% More than 100 dB

Laser output

Frequency response Signal-to-noise ratio
Dynamic range Harmonic distortion

Channel separation

Output
Jack type LINE OUT DIGITAL OUT (OPTICAL) (CDP-CE505/ C450Z only) PHONES (CDP-CE505/ C450Z only) Phono jacks Maximum output level 2V (at 50 kilohms) Load impedance Over 10 kilohms Wave length: 660nm
Optical 18dBm output connector Stereo 10 mW phone jack

32 ohms

General
Power requirements Where purchased USA Australia Power requirements 120 V AC, 60 Hz 240 V AC, 50/60 Hz
Power consumption Dimensions (approx.) (w/h/d)
14 W 385 mm (3/1/4 in.) incl. projecting parts 5.6 kg (12 lbs 6 oz)

Mass (approx.)

Supplied accessories
Audio cord (2 phono plugs 2 phono plugs) (1) Remote commander (remote) (except for CDP-CE305, CDP-C250Z and CDP-C661) (1) Sony SUM-3 (NS) batteries (except for CDP-CE305, CDPC250Z and CDP-C661) (2) Design and specifications are subject to change without notice.
Index Additional Information
AMS 9 Automatic Music Sensor. See AMS
Scanning. See Music Scan Searching. See Locating Select Shuffle Play 11 Shuffle Play 10
Names of controls Buttons
CHECK 12 CLEAR 12 CONTINUE 6 DISC 6 DISC CHECK 9 DISC SKIP 7 EDIT/TIME FADE 13 ERASE 12 EX-CHANGE 8 FADER 14 FILE 17 LINE OUT LEVEL +/ 4 MUSIC CLIP MUSIC SCAN 10 Number 10 OPEN/CLOSE 6 PEAK SEARCH 15 PROGRAM 11 REPEAT 10 SHUFFLE 10 TIME P 7 p 7 0/) 10 / 9 > 10 10
Time Edit 13 Time Fade 15 Total playing time 8 Troubleshooting 19
Clip Play 17 Connecting 4 Continuous Play 6

Delete Bank 17

Unpacking 4

Editing. See Recording

V, W, X, Y, Z