CDP-XA50ES

SERVICE MANUAL

AEP Model E Model

Photo: Black
Model Name Using Similar Mechanism CD Mechanism Type Base Unit Name Optical Pick-up Name
NEW CDM32BB-12B (BLACK) CDM32BN-12B (GOLD) BU-12B KSS-273B/J1N

SPECIFICATIONS

Continued on next page

COMPACT DISC PLAYER

MICROFILM
TABLE OF CONTENTS 1. SERVICING NOTES
1-1. How to Open the Disc Tray When Power Switch Turns Off... 3 1-2. Preparation for Adjustment and Measurement. 3

2. 3. 4.

GENERAL.. 4 DISASSEMBLY... 15 TEST MODE
4-1. AF Mode... 20 4-2. ADJ Mode... 21 4-3. CLV-S Mode... 21
6-1. 6-2. 6-3. 6-4. 6-5. 6-6. 6-7.
ELECTRICAL ADJUSTMENTS.. 22 DIAGRAMS

MODEL IDENTIFICATION

BACK PANEL

4-986-742-

AEP Model : 1 (CED) Singapore Model : 2 (SP)
Printed Wiring Boards SERVO Section .. 25 Schematic Diagram SERVO Section . 27 Schematic Diagram AUDIO Section . 32 Printed Wiring Boards AUDIO Section .. 37 Printed Wiring Boards PANEL Section .. 39 Schematic Diagram PANEL Section . 41 Printed Wiring Boards POWER SUPPLY Section .. 44 6-8. Schematic Diagram POWER SUPPLY Section .. 47 6-9. IC Pin Function Description.. 54
EXPLODED VIEWS.. 60 ELECTRICAL PARTS LIST.. 66
SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
SECTION 1 SERVICING NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pick-up block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens. Notes on chip component replacement Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may be damaged by heat. Flexible Circuit Board Repairing Keep the temperature of the soldering iron around 270 C during repairing. Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). Be careful not to apply force on the conductor when soldering or unsoldering.
HOW TO OPEN THE DISC TRAY WHEN POWER SWITCH TURNS OFF
Insert a tapering driver into the aperture of the unit bottom, and turn in the direction of arrow (to OUT direction).

tapering driver

* To close the disc tray, turn the tapering driver in the reverse direction (to IN direction).
PREPARATION FOR ADJUSTMENT AND MEASUREMENT
CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
Perform connecting the IC261 pin 2 of SERVO board to the line of +5V because this unit does not work without the stabilizer structurally.
[SERVO BOARD] Conductor side
This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior.
Laser component in this product is capable of emitting radiation exceeding the limit for Class 1. The following caution label is located inside the unit.
This section is extracted from instruction manual.

SECTION 2 GENERAL

SECTION 3 DISASSEMBLY
This set can be disassembled in the order shown below.
LOADING PANEL SECTION (Page 15)
CASE (TOP PLATE ), FRONT PANEL SECTION (Page 16)

AUDIO BOARD (Page 16)

MECHANISM DECK (CDM32BB-12B/CDM32BN-12B) (Page 17)

SERVO BOARD (Page 17)

PANEL (DRAWER) (Page 18)
BASE UNIT (BU-12B) (Page 18)
SLED MOTOR (M21), OPTICAL PICK-UP (KSS-273B/J1N) (Page 19)
Note: Follow the disassembly procedure in the numerical order given.

LOADING PANEL SECTION

5 connector (CN292)

4 loading panel section

3 two hexagon hole bolts (LID) (for black/gold)
1 Open the tray turning the tapering screwdriver to the arrow direction.

2 two screws (KTP3 8) (for black/gold)
CASE (TOP PLATE), FRONT PANEL SECTION
1 three flat head screws 9 three connectors (CN351, 352, 461) 1 three flat head screws

2 case (top plate)

3 two connectors (CN201, 993) 6 four screws (3 8)
7 two brakets (case) 4 screw (3 8)
0 front panel section 4 two screws (3 8) 3 two connectors (CN202, 203) 8 two screws (K3 8) 5 lag 4 four screws (3 8) 6 eight screws (BVB) 4 TR screw 3 two connectors (CN401, 501)

AUDIO BOARD

3 two connectors (CN922, 923)
3 four connectors (CN103, 104, 105, 202) 3 four connectors (CN402, 502, 610, 611) 7 audio board 3 two connectors (CN608, 609)
2 side plate (R) 1 four flat head screws
MECHANISM DECK (CDM32BB-12B/CDM32BN-12B)
2 two screws 2 two screws 3 clamp 3 clamp
4 mechanism deck (CDM32BB-12B) (CDM32BN-12B)

1 connector (CN952)

1 connector (CN105)

SERVO BOARD

1 two screws (BVTP3 6) 1 two screws (BVTP3 6) 5 six screws (BVTP3 6)
1 two connectors (CN103, 104) 3 wire (flat type) (26 core) (CN102) 4 wire (flat type) (12 core) (CN101)

2 bracket (servo)

6 servo board

bracket (servo)

PANEL (DRAWER)

1 two tapping screws

3 Remove the panel (drawer) to direction of the arrow.

2 two ditch

BASE UNIT (BU-12B)
4 two screws (PTPWH2.6 8)
4 two screws (PTPWH2.6 8) 5 two holders (SP)
5 two holders (SP) 1 flexible board (CN192) 6 base unit

7 two coil springs (F)

7 flexible board (CN291) 7 two coil springs (F)

2 screw (B2.6 10)

SLED MOTOR (M21), OPTICAL PICK-UP (KSS-273B/J1N)
2 two screws (BTP2.6 8) 7 poly-slider washer 8 gear (D) 4 tapping screw 5 lag

3 leaf spring (skew)

9 Remove the sled motor (M21) and optical pick-up (KSS-273B/J1N) to direction of the arrow A.

6 leaf spring (OP)

A 0 bracket (OP base)

1 flexible board (CN11)

4 tapping screw

SECTION 4 TEST MODE

4-1. AF MODE

REPEAT button

SIDE-B ( MIN TIME ) (1)
Connect the TP2 (AFJ) on the SERVO board to the ground and turn on the power supply. The AF mode is then activated and the following check can be made. 4-1-1. Fluorescent Indicator Tube Check After confirming display of all on, keep pressing the following button, and the following display is attained. p (STOP) button

C. FILE

(Display: 09)

TIME button

(Display: 01)

(Display: 10)

(PLAY) button Keep pressing the OPEN/CLOSE button, and all on display is attained again. 4-1-2. Key Check All buttons are assigned with numbers respectively, and when each button is pressed, it is counted and its number is displayed. Up to 16 can be counted. A button pressed once is not further counted but the number is displayed.

(Display: 02)

P (PAUSE) button

Table 4-1.

Button ERASE

(Display: 03)

Display 23 all light up 01 02
Button P ) 0 CHECK CLEAR P MODE REPEAT TIME

Display 09 10

EDIT/ TIME FADE FILE FILTER

) button

SHUFFLE REPEAT AAUTO SPACE STEP EDIT

PUSH ENTER

(Display: 04)

OPEN/CLOSE p (

0 button
1 PROGRAM INDEX PEAK B ( JUST )

(Display: 05)

CHECK button 15

(Display: 06)

4-1-3. Remote Commander Check Press the ( button on remote commander, and ( on the set turn on. Nothing will be displayed if pressing another button.

CLEAR button 10

(Display: 07) count display button number display

P MODE button

SIDE-A FADE C. SEC DELETE CUSTOM INDEX

(Display: 08)

4-2. ADJ MODE
Connect the TP1 (ADJ) on the SERVO board to the TP (GND) and turn on the power supply. The ADJ mode is then activated and the following operation is executed. There is no problem even if GFS is low value continuously during playing. Do not perform high speed search during an access. The gain of focus servo and spindle servo does not lower during playing. Manual operation and measurement of the servo system are possible. (For detailed operating method, see Table 4-2. in ADJ Mode.) 4-2-1. Button Operation Table in ADJ Mode After all music numbers are displayed, press the TIME button, and the jitter display mode is then set. The button functions are as listed below. Button Functions (Operate with remote commander.)

TP (GND) IC101

TP 1 (ADJ)

TP 2 (AFJ)

Table 4-2.
Button No. Test Mode Tracking servo off Tracking servo on S-curve measuring mode All servo off Top turnback display Botton turnback display Center display Optimum point display Optimum jitter display TE traverse display VC, FE and RF display Autogain display (Focus, tracking and sled)

Procedure: 1. Connect the frquency counter to TP (PLK). 2. Turned power switch on. 3. Put disc (YEDS-18) in and press the ( button. 4. Confirm that the reading on frequency counter is 4.3218 MHz.

SECTION 6 DIAGRAMS

Skew Adjustment Note : Do not perform the skew adjustment when not using attached stabilizer to a set.
oscilloscope (AC range) SERVO board TP (RF) TP (VC)

Circuit Boards Location

TP (TEI) 29 (FEI) TP (RFI) TP (FE) TP (RF) IC101 BSL board TP1 (ADJ) TP2 (AFJ) SERVO board LOADING MOTOR board FUSE board POWER board COAX board
TP (TE) TP TP (VC) (PLK) CN102
CN101 RF signal waveform VOLT/DIV: 200 mV TIME/DIV: 500 ns (with the 10: 1 probe in use) level: 1.2 0.20 Vp-p

SW board

OPT board

LINE board VR board

KEY-R board

AUDIO board

DISPLAY board
LOADING SW board KEY-L board FL RELAY board

FLEX RELAY board

adjustment screw

screwdriver

1. Remove the bottom plate, put one third of the unit out from the desk. 2. Connect the osiclloscope to TP (RF) and TP (VC) on SERVO board. 3. Turned power switch on. 4. Put disc (YEDS-18) in and press the ( button. 5. Adjust to be clear the waveform of the oscilloscope turning the adjsutment screw with a screwdriver. Note: Clear RF signal waveform means that the shap can be clearly distinguished at the center of the waveform. 6. After the adjustment, lock the adjustment screw.
IC Block Diagrams SERVO Section IC91 M51957AL IC203 LB1641

T.S.D MOTOR DRIVE

O.C.P MOTOR DRIVE

VDD IN

FWD/REV/STOP CONTROL LOGIC

MOTOR DRIVE

NOISE FILTER

FWD.IN

REV.IN

IC101 CXD2545Q

ATSK DFSW SCLK DIRC XRST SENS MUTE SQSO SQCK COUT FOK DFCT MIRR LOCK CLOK DATA SFDR SSTP EXCK 76 SUBCODE P-W PROCESSOR XLAT 87 MON MDS MDP FSW ADD 90
SRON SRDR SFON TFDR TRON TRDR TFON FFDR FRON FRDR FFON

SLED PWM GENERATOR

SLED SERVO

CPU INTERFACE

SUBCODE Q PROCESSOR

75 SBSO

TRACKING PWM GENERATOR

CLOCK GENERATOR

1 VSS2

2 L2 (+)

4 L2 ()

6 VDD2

7 VSUB (A) L

8 XVDD

9 XOUT
VSUB (A) R R2 () R2 (+) XIN XVSS XVSS VDD2 VDD VSS VSS2

CXD8679Q

NRGCLR 128FSO CKVDD LATCH INVO2 INVO1 LRCKI DATAI SYSM SHIFT DINIT BCKI INVI VSS VSS INIT ATT
TIMING CIRCUIT IF SELD 52 IF SELC 53 NC 54 SBCKI 55 SDATAR 56 IIR SDATAL 57 NC 58 DFDTOL 59 DFBCKO 60 OVERFLOW DETECTOR DFDTEN 61 TESTTESTVSS 64 P/S CONVERT & D/F-CLK GEN. OVERFLOW DETECTOR POLALITY 23 DFLRCKO 22 TESTTEST3 CLOCK GENERATOR 20 VSS BITSTREAM IIR ATT x 0.75 DITHER FIR 4 FIR 1 FIR 2 FIR 3 FIR 4 FIR 1 FIR 2 FIR 3 ATT x 0.75 L. I. P. 3rd order NOISE SHAPER 26 MODE 25 NC 24 DFDTOR 4BIT DATA ATT MODE ATT L. I. P. S/P OR "0" DETECT MUTE CIRCUIT

VCC PR Q

PANEL Section
32 INAF 31 OVFLAG 30 MUTER 29 MUTEL 28 MTPOL C 27 DRPOL 1

TC7W74F

IC801-803

LC7570E

DATA VFL S0 S1 S2 S3 NC S4 WR CL

3rd order NOISE SHAPER

NC 1 BLK 2 VSS 3 SIN S33 S32 S31 S30 S29 S28 S27 SSHIFT REGISTER A/D CONVERTER

NC VDA

LATCH, FL DRIVER
S5 S6 S7 S8 S9 S10 S11 S12 S13 S14 S15 S16
DATA SELECT 2 DATA SELECT
NC S25 S24 S23 S22 S21 NC S20 S19 S18 S17 NC

NSDOL4

NSDOL3

NSDOL2

NSDOL1

NSDOR1

NSDOR2

NSDOR3

NSDOR4

Waveforms

SERVO Section AUDIO Section
6-9. IC PIN FUNCTION DESCRIPTION
SERVO BOARD IC101 CXD2545Q (DIGITAL SIGNAL PROCESSOR, FOCUS/TRACKING/SLED SERVO, EFM COMPARATOR) Pin No. Pin Name 3

1.2 +0.25 Vp-p 0.20

5.2 Vp-p
1 IC101 @ (RFDC) 200 mV/DIV, 500 ns/DIV

6 IC101 $ (BLCK)

1 IC602 1
I/O O O O O O O O O O O O O I I I I O O I I I O I I I I I O I O I I I I O I I
Function Sled servo drive PWM signal output terminal Sled servo drive PWM signal output terminal Not used (open) Not used (open) Not used (open) Not used (open) Not used (open) Not used (open) Not used (open) Not used (fixed at L) Sled servo drive PWM signal () output to the BA6297AFP (IC102) Tracking servo drive PWM signal () output to the BA6297AFP (IC102) Tracking servo drive PWM signal output terminal Tracking servo drive PWM signal output terminal Focus servo drive PWM signal output terminal Focus servo drive PWM signal output terminal Tracking servo drive PWM signal (+) output to the BA6297AFP (IC102) Focus servo drive PWM signal (+) output to the BA6297AFP (IC102) Focus servo drive PWM signal () output to the BA6297AFP (IC102) Oscillator circuit output terminal for analog PLL of the playback EFM Oscillator circuit input terminal for analog PLL of the playback EFM Input terminal for the test (fixed at L) Ground terminal (digital system) Input terminal for the test (fixed at L) Input terminal for the test (fixed at L) Charge-pump output terminal for analog PLL of the playback EFM PLL charge-pump output terminal for the variable pitch Power supply terminal (+5V) (analog system) Power supply terminal (+5V) (for operational amplifier) Ground terminal (analog system) Input terminal for the A/D converter Not used (open) Not used (open) Output terminal of the operational amplifier Clock signal input from external VCO for the variable pitch Not used (open) Not used (open) Not used (fixed at L)

Sub-code sync (S0+S1) detection signal output to the system controller (IC201)
Pin No. Pin Name SBSO EXCK SUBQ SQCK MUTE SENS XRST DIRC SCLK DFSW ATSK DATA XLAT CLOK COUT DVDD MIRR DFCT FOK FSW MON MDP MDS LOCK SSTP SFDR
I/O O I O I I O I I I I I I I I O O O O O O O O O I O Sub-code P-W serial data output terminal
Function Not used (open) Not used (fixed at L) Sub-code P-W serial data reading clock signal input terminal Sub-code Q data signal output to the system controller (IC201) Sub-code Q data reading clock signal input from the system controller (IC201) Mute signal input from the system controller (IC201) Internal status (SENSE) signal output to the system controller (IC201) System reset signal input from the reset signal generator (IC91) L: reset For several hundreds msec. after the power supply rises, L is input, then it changes to H 1-track jump mode input terminal Not used (fixed at H) Not used (fixed at L) Sense serial data reading clock signal input from the system controller (IC201) Defect on/off select signal input terminal Input terminal for the anti-shock Not used (fixed at L)
Serial data input from the system controller (IC201) Serial data latch pulse signal input from the system controller (IC201) Serial data transfer clock signal input from the system controller (IC201) Track number count signal output terminal Mirror detection signal output terminal Defect signal output terminal Focus OK signal output terminal Not used (open) Power supply terminal (+5V) (digital system) Not used (open) Not used (open) Not used (open) Not used (open) Not used (open)
Selection signal output terminal of the output filter for spindle motor Spindle motor on/off control signal output terminal Spindle servo control signal output terminal
Spindle servo control signal output terminal Not used (open) GFS is sampled by 460 Hz H output when GFS is H Not used (open) Detection input from the sled limit-in detect switch (S22) The optical pick-up is inner position when H Sled servo drive PWM signal (+) output to the BA6297AFP (IC102)
SERVO BOARD Pin No. Pin Name A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 WE NC NC LED-PLAY LED-PAUSE LED-FILTER
IC201 I/O O O O O O O O O O O O O O O O O O O O O O O O O O O O I I I I O O I I I I I
CXP84124-068Q (SYSTEM CONTROLLER) Function
Address signal output to the static RAM (IC202)
Write enable signal output to the static RAM (IC202) Not used (open) Not used (open) ( LED (D871) drive signal output terminal P LED (D872) drive signal output terminal H: LED on H: LED on H: LED on L: reset

FILTER LED (D873) drive signal output terminal Reset signal output to the CXD2562Q-CS (IC603)
SPDL-MUTE SHIFT-ON/OFF VOL UP VOL DOWN BLANK FL D0 FL D1 FL D2 FL CLK FL WR SENSER SW SENSER LIMIT OUT RESET XTALI XTALO VSS TX TEX AVSS AVREF K0 K1 K2
Mute signal output to the spindle motor driver (IC104, 105) Volume up control signal output to the volume control motor driver (IC350) Volume down control signal output to the volume control motor driver (IC350) Blank signal output to the fluorescent indicator tube driver (IC801 to IC803) Serial data output to the fluorescent indicator tube driver (IC803) Serial data output to the fluorescent indicator tube driver (IC802) Serial data output to the fluorescent indicator tube driver (IC801) Serial data transfer clock signal output to the fluorescent indicator tube driver (IC801 to IC803) Read/write select signal output to the fluorescent indicator tube driver (IC801 to IC803) On/off control signal output to the stabilizer detect sensor (IC261) Detect signal input from the stabilizer detect sensor (IC261) Detection input from the sled limit-out detect switch (S21) The optical pick-up is outer position when L System reset signal input from the reset signal generator (IC91) L: reset For several hundreds msec. after the power supply rises, L is input, then it changes to H Main system clock input terminal (4 MHz) Main system clock output terminal (4 MHz) Ground terminal Sub system clock output terminal Sub system clock input terminal Ground terminal (for A/D converter) Reference voltage input terminal (+5V) Key input terminal (A/D input) ERASE key (S850) input Key input terminal (A/D input) FILE, EDIT/TIME FADE, TIME, REPEAT, P MODE keys (S851 to S855) input Key input terminal (A/D input) CHECK, CLEAR, FILTER, 0, ) , PUSH ENTER keys (S884 to S888, RV870) input Not used (open) Not used (fixed at L) H: on H: on

Pin No. *1

Pin Name K3 K4 K5 ADJ/AFJ IN/OUT SW SCLK PRGL CLK SENSE DATA SQCK SUBQ TEST SEL1 SEL0 RMIN TIMER TEST TEST SCOR AMUTE LDON XLT LOAD OUT LOAD IN DOUT DMUTE D0 D1 D2 D3 VDD NC D4 D5 D6 D7 A0 A1 A2

I/O I I I I I O O O I O O I O I I I I O O I O O O O O O O I/O I/O I/O I/O I I/O I/O I/O I/O O O O Power supply terminal (+5V) Not used (fixed at H)
Function Key input terminal (A/D input) OPEN/CLOSE, (, P, p keys (S889 to S892) input Rotary encoder input terminal (A/D input) Rotary encoder input terminal (A/D input) Setting terminal for the test mode AMS key (RV870) input AMS key (RV870) input

L active

Detection input from the loading in/out detect switch (S281, S282) (A/D input) Sense serial data reading clock signal output to the CXD2545Q (IC101) Serial data latch pulse signal output to the CXD8679Q (IC601) Serial data transfer clock signal output to the CXD2545Q (IC101) and CXD8679Q (IC601) Internal status (SENSE) signal input from the CXD2545Q (IC101) Serial data output to the CXD2545Q (IC101) and CXD8679Q (IC601) Sub-code Q data reading clock signal output to the CXD2545Q (IC101) Sub-code Q data signal input from the CXD2545Q (IC101) Output terminal for the test Not used (open) Destination setting terminal (fixed at L) Destination setting terminal (fixed at L) Remote control signal input from the remote control receiver (IC804) Timer control input terminal Output terminal for the test Output terminal for the test Not used (fixed at H) Not used (open) Not used (open)
Sub-code sync (S0+S1) detection signal input from the CXD2545Q (IC101) Muting control signal output to the analog mute driver and mute relay driver Laser diode on/off selection signal output to the RF amplifier in optical pick-up Serial data latch pulse signal output to the CXD2545Q (IC101) Loading motor (M271) drive signal output to the LB1641 (IC203) Loading motor (M271) drive signal output to the LB1641 (IC203) Digital out on/off control signal output to the CXD2545Q (IC101) Muting control signal output to the CXD2545Q (IC101) and CXD8679Q (IC601) *1 *1
Two-way data bus with the static RAM (IC202)
Loading motor (M271) control
Operation Terminal LOAD OUT (pin ^) LOAD IN (pin ^)

OFF L L

OUT H L

IN L H

BRAKE H H

Main Ports

SPDL-MUTE (pin !) From the viewpoint of performance of the set, the disc must not move nor sway when the disc table opens. These problems however occur in the actual case due to the offset voltage generated and the voltage generated because of the positional relation between the BSL coil and Hall element. The spindle motor driver (IC104, IC105) is therefore muted while the tray is open. Pin ! provides the timing for this. SENSER (pin @) The results of the detection of IC261 IS471F is output to this pin. It becomes L when there is no stabilizer (when light reaches). The next process of imposing the next focus is not performed. (Effective only when pin @ is H.) Therefore, it must be noted that if PLAY is performed when the servo board at the top of the CDM is not assembled properly, the detection circuit operates and this pin does not operate. It is does not operate, refer to 1. SERVICING NOTES Preparations for Adjustment and Measurement on page 3.

(6) BASE UNIT SECTION (BU-12B) 270

274 268

261 270

252 262

M21 not supplied #1

S21, S22

273 251
The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. Part No. 4-970-924-01 8-820-014-01 4-968-944-01 4-968-865-01 4-968-879-01 3-364-731-01 4-968-864-01 4-968-862-01 1-653-918-11 4-971-266-01 Description SPRING (SKEW), LEAF OPTICAL PICK-UP KSS-273B/J1N SHAFT, SLED GEAR (C) SPRING (OP), LEAF WASHER, POLY-SLIDER GEAR (B) BASE, MECHANICAL FLEXIBLE BOARD SCREW (M2.6X4) Remark

Ref. No. 251 * 264

Part No. A-4660-688-A A-4699-545-A X-4945-273-1 3-701-444-11 X-4945-203-1 A-4660-814-A 4-968-871-01 4-968-867-01 4-968-869-01 4-968-870-01 4-968-880-01 4-968-866-01 4-917-562-21 4-968-916-01
Description STABILIZER ASSY BSL BOARD, COMPLETE ROTOR ASSY WASHER, 6 BASE ASSY, SLIDE
Ref. No. 265 ! 266 * 271 * 274 M21 S21 S22
PULLEY ASSY, DISK WASHER (SPINDLE) CAP, CENTERING SPRING (CENTERING), COMPRESSION RACK, SLIDE SPRING (SLED), COMPRESSION GEAR (D) INSULATOR BRACKET (OP BASE)
X-4945-920-1 MOTOR ASSY (SLED) 1-571-958-11 SWITCH, PUSH (1 KEY) (LIMIT OUT) 1-571-958-11 SWITCH, PUSH (1 KEY) (LIMIT IN)
NOTE: Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. -XX and -X mean standardized parts, so they may have some difference from the original one. RESISTORS All resistors are in ohms. METAL: Metal-film resistor. METAL OXIDE: Metal oxide-film resistor. F: nonflammable
SECTION 8 ELECTRICAL PARTS LIST
Items marked * are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. SEMICONDUCTORS In each case, u: , for example: uA. : A. uPA. : PA. uPB. : PB. uPC. : PC. uPD. : PD. CAPACITORS uF: F COILS uH: H The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. When indicating parts by reference number, please include the board.

Ref. No.

Part No.
Ref. No. C514 C517 C518 C519 C520 C521 C522 C523 C524 C525 C528 C529 C530 C531 C532 C533 C534 C535 C536 C537 C541 C551 C552 C553 C601 C602 C603 C604 C605 C606 C607 C608 C609 C610 C611 C612 C613 C614 C615 C621 C622 C623 C624 C625
Part No. 1-136-810-11 1-136-817-91 1-136-814-11 1-104-646-11 1-117-775-31 1-128-197-11 1-136-850-11 1-136-850-11 1-136-850-11 1-136-850-11 1-136-850-11 1-136-850-11 1-136-850-11 1-130-973-00 1-130-969-11 1-130-969-11 1-136-233-11 1-136-233-11 1-128-200-11 1-128-200-11 1-164-159-11 1-162-199-31 1-126-024-11 1-162-199-31 1-126-023-11 1-164-732-11 1-164-159-11 1-164-732-11 1-164-159-11 1-164-732-11 1-162-290-31 1-128-200-11 1-117-775-31 1-164-732-11 1-102-947-00 1-102-947-00 1-128-201-11 1-162-290-31 1-164-732-11 1-117-855-51 1-117-855-51 1-126-023-11 1-126-023-11 1-128-201-11

1-259-452-11 1-259-472-11 1-259-444-11 1-259-476-11 1-259-456-11 1-259-464-11 1-259-468-11 1-259-396-11 1-259-416-11 1-259-416-11 1-259-416-11 1-259-416-11 1-249-931-11 1-259-440-11 1-249-913-11 1-249-913-11 1-249-885-11 1-249-885-11 1-249-946-11 1-249-946-11 1-249-946-11 1-249-946-11 1-249-923-11 1-249-923-11 1-249-520-11 1-249-959-11 1-249-931-11 1-249-637-11 1-249-979-91 1-249-995-11 1-249-979-91 1-249-977-11 1-249-506-11 1-249-917-11 1-249-504-11 1-249-504-11 1-249-504-11 1-249-504-11 1-259-476-11 1-259-452-11 1-259-472-11 1-259-444-11 1-259-476-11 1-259-456-11 1-259-464-11 1-259-468-11 1-259-396-11 1-259-416-11 1-259-416-11 1-259-416-11
1-259-428-11 CARBON 1-259-428-11 CARBON 1-259-428-11 1-259-428-11 1-259-424-11 1-259-424-11 1-259-420-11 1-259-430-11 1-259-420-11 1-259-420-11 1-249-947-11 1-259-416-11 1-259-412-11 1-259-448-11 1-259-420-11 1-212-887-00 1-259-484-11 1-259-460-11 1-259-476-11 1-219-022-11 1-219-022-11 CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON FUSIBLE CARBON CARBON CARBON FUSIBLE FUSIBLE < VIBRATOR >
X601 1-577-685-11 FILTER, CRYSTAL (16MHz) X602 1-579-161-11 VIBRATOR, CRYSTAL (45MHz) ************************************************************ * A-4699-545-A BSL BOARD, COMPLETE ******************* < CONNECTOR > CN11 1-580-864-11 SOCKET, CONNECTOR (SMT) 10P < HOLE ELEMENT > H11 H12 8-719-987-62 DIODE LT140SAZ 8-719-987-62 DIODE LT140SAZ < RESISTOR/CHIP CONDUCTOR > R11 1-216-049-91 METAL CHIP 1K 5% 1/10W R12 1-216-049-91 METAL CHIP 1K 5% 1/10W R13 1-216-295-91 CONDUCTOR, CHIP (2012) R14 1-216-295-91 CONDUCTOR, CHIP (2012) R15 1-216-295-91 CONDUCTOR, CHIP (2012) ************************************************************ * 1-663-631-11 COAX BOARD *********** < CAPACITOR > C702 C703 C704 C705 C706 1-104-645-11 1-164-732-11 1-136-165-00 1-107-611-11 1-164-732-11 CERAMIC CERAMIC FILM MICA CERAMIC 1uF 0.1uF 0.1uF 100PF 0.1uF 20% 20% 5% 5% 20% 50V 50V 50V 500V 50V
1-259-416-11 CARBON 1-249-931-11 CARBON 1-259-440-11 CARBON
The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified.
Ref. No. C707 C708 Part No.

DISPLAY

Description 100uF 100PF

FL RELAY

Remark 20% 25V 10% 50V

FLEX RELAY

Ref. No. Part No.

FLEXIBLE

1-126-023-11 ELECT 1-162-282-31 CERAMIC < CONNECTOR >
R803 1-216-097-00 METAL CHIP 100K 5% 1/10W ************************************************************ * 1-653-906-11 FL RELAY BOARD ************** < CONNECTOR > CN291 1-568-794-11 SOCKET, CONNECTOR 12P * CN292 1-568-950-11 PIN, CONNECTOR 12P ************************************************************ * 1-654-005-11 FLEX RELAY BOARD **************** < CONNECTOR >

CN701 CN703

1-580-771-11 PIN, CONNECTOR (PC BOARD) 3P 1-580-771-31 PIN, CONNECTOR (PC BOARD) 3P < IC >
8-759-242-70 IC TC7WU04F < PIN JACK >
1-507-567-71 JACK, PIN 1P (DIGITAL OUT COAXIAL) < RESISTOR >

R701 R702

1-259-401-11 CARBON 1-259-412-11 CARBON

75 220

1/6W 1/6W
CN191 1-580-473-11 SOCKET, CONNECTOR 26P CN192 1-580-460-11 SOCKET, CONNECTOR 26P ************************************************************ 1-653-918-11 FLEXIBLE BOARD ************** < SWITCH > S21 1-571-958-11 SWITCH, PUSH (1 KEY) (LIMIT OUT) S22 1-571-958-11 SWITCH, PUSH (1 KEY) (LIMIT IN) ************************************************************ * 1-663-628-11 FUSE BOARD ********** 1-533-233-11 HOLDER, FUSE < CAPACITOR > ! C991 ! C992 ! C993 1-113-924-11 CERAMIC 1-113-924-11 CERAMIC 1-113-925-11 CERAMIC < CONNECTOR > 0.0047uF 20% 250V 0.0047uF 20% 250V 0.01uF 20% 250V
< COIL WITH CORE > T701 1-459-795-11 COIL (WITH CORE) ************************************************************ * 1-654-256-11 DISPLAY BOARD ************* 4-969-510-01 HOLDER (FL) < CAPACITOR > C801 C802 C803 C804 C805 C806 C807 1-163-038-00 1-163-031-11 1-163-031-11 1-163-031-11 1-163-031-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.01uF 0.01uF 0.01uF 0.01uF 0.01uF 0.01uF 25V 50V 50V 50V 50V 50V 50V
1-163-031-11 CERAMIC CHIP 1-163-031-11 CERAMIC CHIP
< FLUORECENT INDICATOR TUBE > FLD801 1-517-357-11 INDICATOR TUBE, FLUORESCENT < IC > IC801 IC802 IC803 IC804 8-759-324-36 8-759-324-36 8-759-324-36 8-749-923-80 IC IC IC IC LC7570E LC7570E LC7570E GP1U90XB * CN991 CN992 CN993 CN994 1-564-321-21 1-770-128-11 1-564-321-00 1-580-230-11 PIN, CONNECTOR 2P PIN, CONNECTOR 2P PIN, CONNECTOR 2P PIN, CONNECTOR (PC BOARD) 2P < FUSE > ! F991 ! F992 1-532-279-00 FUSE, TIME-LAG (T0.5A/250V) 1-532-279-00 FUSE, TIME-LAG (T0.5A/250V) < LINE FILTER > ! T991 1-421-915-11 COIL, LINE FILTER ************************************************************

0.0015uF 5% 0.22uF 10% 0.15uF 10% 0.1uF 0.1uF 0.1uF 0.33uF 0.1uF 0.1uF 0.33uF 0.1uF 0.1F 0.1uF 0.1uF 0.1uF 0.01uF 0.1uF 100uF
1-259-460-11 CARBON 1-259-440-11 CARBON < THERMISTOR >
TH903 1-806-882-11 THERMISTOR, POSITIVE TH904 1-808-065-11 THERMISTOR, POSITIVE ************************************************************ * A-4699-587-A SERVO BOARD, COMPLETE ********************** < CAPACITOR > C93 C94 C95 C96 C97 C101 C102 C103 C104 C105 C106 C107 C108 C109 C110 C111 C112 C113 C114 C115 C131 C132 C133 1-124-995-11 1-124-995-11 1-124-995-11 1-163-141-00 1-126-162-11 1-126-177-11 1-126-177-11 1-163-017-00 1-163-133-00 1-164-004-11 1-163-133-00 1-163-809-11 1-163-145-00 1-163-117-00 1-164-489-11 1-164-232-11 1-163-038-00 1-163-038-00 1-163-038-00 1-164-346-11 ELECT ELECT ELECT CERAMIC CHIP ELECT ELECT ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 220uF 220uF 220uF 0.001uF 3.3uF 100uF 100uF 0.0047uF 470PF 0.1uF 470PF 0.047uF 0.0015uF 100PF 0.22uF 0.01uF 0.1uF 0.1uF 0.1uF 1uF 47PF 5% 0.0047uF 5% 0.0047uF 5% 20% 20% 20% 5% 20% 20% 20% 5% 5% 10% 5% 10% 5% 5% 10% 10V 10V 10V 50V 50V 10V 10V 50V 50V 25V 50V 25V 50V 50V 16V 50V 25V 25V 25V 16V 50V 50V 50V
1-164-232-11 CERAMIC CHIP 1-163-038-00 CERAMIC CHIP 1-126-177-11 ELECT < CONNECTOR >
* CN91 CN101 CN102 CN103 CN104 CN105 CN201 CN202 CN203 CN251
1-573-278-11 1-568-795-11 1-580-473-11 1-580-781-11 1-580-774-11 1-580-771-11 1-580-774-11 1-580-775-11 1-580-770-11 1-580-774-11
PIN, CONNECTOR 8P SOCKET, CONNECTOR 12P SOCKET, CONNECTOR 26P PIN, CONNECTOR (PC BOARD) 7P PIN, CONNECTOR (PC BOARD) 6P PIN, CONNECTOR (PC BOARD) 3P PIN, CONNECTOR (PC BOARD) 6P PIN, CONNECTOR (PC BOARD) 8P PIN, CONNECTOR (PC BOARD) 2P PIN, CONNECTOR (PC BOARD) 6P < DIODE >

D201 D202 D261

8-719-914-44 DIODE DAP202K 8-719-976-96 DIODE DTZ4.7C 8-719-938-07 LED GL480 (STABILIZER DETECT) < IC >
1-163-109-00 CERAMIC CHIP 1-163-017-00 CERAMIC CHIP 1-163-017-00 CERAMIC CHIP

IC91 IC101 IC102

8-759-636-16 IC M51957AL 8-752-369-78 IC CXD2545Q 8-759-071-79 IC BA6297AFP
Ref. No. IC103 IC104 IC105 IC201 IC202 IC203 IC261 Part No. Description Remark Ref. No. R143 R144 R145 R146 R147 R148 R149 R150 R151 R152 R153 R154 R155 R161 R162 R163 R164 R165 R166 R167 R168 R171 R172 R173 R174 R175 R176 R179 R180 R181 R182 R183 R184 R201 R202 R203 R204 R205 R206 R207 R208 R209 R210 R212 R213 R214 R261 Part No. 1-216-093-00 1-216-093-00 1-216-085-00 1-216-085-00 1-216-308-00 1-216-073-00 1-216-073-00 1-216-073-00 1-216-097-00 1-216-001-00 1-216-001-00 1-216-073-00 1-216-097-00 1-216-075-00 1-216-091-00 1-216-093-00 1-216-093-00 1-216-093-00 1-216-097-00 1-216-065-00 1-216-097-00 1-216-001-00 1-216-105-00 1-216-057-00 1-216-057-00 1-216-105-00 1-216-308-00 1-216-001-00 1-216-105-00 1-216-057-00 1-216-057-00 1-216-105-00 1-216-308-00 1-216-013-00 1-216-069-00 1-216-069-00 1-216-069-00 1-216-069-00 1-216-069-00 1-216-069-00 1-216-069-00 1-216-069-00 1-216-073-00 1-216-073-00 1-216-073-00 Description METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 68K 68K 33K 33K 4.7 10K 10K 10K 100K 10K 100K 12K 56K 68K 68K 68K 100K 4.7K 100K 10 220K 2.2K 2.2K 220K 4.220K 2.2K 2.2K 220K 4.6.8K 6.8K 6.8K 6.8K 6.8K 6.8K 6.8K 6.8K 10K 10K 10K 100K 68 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% Remark 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W

1-427-816-11 TRANSFORMER, POWER (for AUDIO)
1-663-636-11 SW BOARD ******** 1-696-874-21 LEAD (WITH CONNECTOR) < SWITCH >
! T902 1-427-817-11 TRANSFORMER, POWER (for DIGITAL) ************************************************************ ************** HARDWARE LIST ************** #1 #2 #3 #4 #5 #6 #7 #9 #10 #11 #12 #13 #14 #15 #16 #17 #18 #19 #20 #21 7-685-246-14 SCREW +KTP 3X8 TYPE2 NON-SLIT (for GOLD) 7-682-248-09 7-682-565-09 7-682-548-09 7-685-880-09 7-685-646-79 7-685-871-01 7-685-873-09 7-685-647-79 7-682-903-01 7-685-645-79 7-682-902-11 7-621-775-50 7-621-772-30 7-685-134-19 7-628-253-00 7-627-852-58 7-685-534-19 7-685-872-09 7-685-246-19 SCREW +K 3X8 SCREW +B 4X16 SCREW (3X8) SCREW +BVTT 4X6 (S) SCREW, TAPPING SCREW +BVTT 3X6 (S) SCREW +BVTT 3X10 (S) SCREW +P 3X10 TYPE2 NON-SLIT SCREW +PWH 3X5 SCREW +BVTP 3X6 TYPE2 N-S SCREW +PWH 2.6X5 SCREW +B 2.6X10 SCREW +B 2X6 SCREW +PTPWH 2.6X8 (TYPE2)
! S991 1-572-267-51 SWITCH, PUSH (AC POWER) (1 KEY) ************************************************************ * 1-663-635-11 VR BOARD ********* 4-962-201-01 PLATE (HP), GROUND < CAPACITOR > C350 C351 C461 C561 1-136-165-00 1-136-165-00 1-162-290-31 1-162-290-31 FILM FILM CERAMIC CERAMIC < CONNECTOR > CN351 * CN352 CN461 1-764-345-11 PIN, CONNECTOR (PCB) (L TYPE) 8P 1-580-772-11 PIN, CONNECTOR (PC BOARD) 4P 1-764-326-11 PIN, CONNECTOR (PCB) (V TYPE) 3P < IC > IC350 8-759-962-08 IC BA6208 < JACK > J461 J461 1-750-162-61 JACK (LARGE TYPE) (PHONES) (BLACK) 1-779-219-11 JACK (LARGE TYPE) (PHONES) (GOLD) < COIL > L461 L561 1-412-473-21 INDUCTOR 1-412-473-21 INDUCTOR 0uH 0uH 0.1uF 0.1uF 470PF 470PF 5% 5% 10% 10% 50V 50V 50V 50V
SCREW +PS 2X4 SCREW, PRECISION +P 1.7X5 TYPE3 SCREW +BTP 2.6X8 TYPE2 N-S SCREW +BVTT 3X8 (S) SCREW +KTP 3X8 TYPE2 NON-SLIT (for BLACK) ************************************************************ ACCESSORIES & PACKING MATERIALS ******************************* 1-473-944-11 1-590-925-31 3-707-584-21 3-858-365-11 REMOTE COMMANDER (RM-D950) CORD, CONNECTION (AUDIO 1m) COVER, BATTERY (for RM-D950) MANUAL, INSTRUCTION (ENGLISH, FRENCH, SPANISH, SWEDISH) 3-858-365-21 MANUAL, INSTRUCTION (GERMAN, DUTCH, ITALIAN, PORTUGUESE) (AEP) 3-858-365-31 MANUAL, INSTRUCTION (CHINESE) (Singapore)
< VARIABLE RESISTOR > 1-223-747-11 RES, VAR, CARBON 10K/10K (LINE OUT PHONE LEVEL) ************************************************************ MISCELLANEOUS ************** ! 158 ! M21 M271 S21 S22 1-558-568-21 1-769-109-11 1-769-110-11 8-820-014-01 1-653-918-11 X-4945-920-1 X-4945-565-1 1-571-958-11 1-571-958-11 CORD, POWER WIRE (FLAT TYPE) (12 CORE) WIRE (FLAT TYPE) (26 CORE) OPTICAL PICK-UP KSS-273B/J1N FLEXIBLE BOARD MOTOR ASSY (SLED) MOTOR ASSY (LOADING) SWITCH, PUSH (1 KEY) (LIMIT OUT) SWITCH, PUSH (1 KEY) (LIMIT IN) RV350

SAA7350BS 4x PCM1704K UltraAnalog D20400A 1x PCM54 (S/H) CX20017 PCM56P J 1x TDA1541 TDA1541 PCM58P CX20152 CX20152 CXD2565M CXD2565M CXD2562 TDA1541 CXD2562 TDA1541 2x PCM58P CXD2561 CX20017 PCM54 CX20152 PCM53JP-V CX20152 PCM54 CX20152 PCM53JP-V K CXD2562 TDA1541A CXD2562 PCM58P PCM54 PCM54 CX20017 PCM58P PCM56P CXD2562Q TDA1541 CXD8594 + CXA8042AS
SONY CDP-R3 + DAS-R1a CXD2552Q + CXD2552 SONY CDP-X229ES CXD2562Q SONY CDP-X3000 CXD2562Q + CXA8042AS SONY CDP-X303ES CXD2562Q SONY CDP-X5000 CXD2562 + CXA8042 SONY CDP-X505ES CXD2562Q SONY CDP-X33ES CXD2552Q SONY CDP-X55ES CXD2552 SONY CDP-X777ES CXD2552BQ SONY CDP-X779ES CXD2562 SONY CDP-X77ES CXD2552 SONY CDP-X7ESD PCM58P S SONY CDP-X900 CXA8042 SONY CDP-XA20ES CXD8505BQ + CXA8042AS SONY CDP-XA30ES CXD2562Q + CXA8042AS SONY CDP-XA50ES CXA8042AS SONY CDP-XA55ES CXD8594Q + CXA8042S SONY CDP-XA5ES CXD2562Q + CXA8042AS SONY CDP-XA7ES CXD2562 + CXA8042AS SONY CDP-XB920 CXD8715 + CXA8355 SONY CDP-XB720E CXD8735N SONY CDP-XB930 CXD8735N SONY CDP-XE300 CXD8567 SONY CDP-XE310 CXD8567 SONY CDP-XE330 CXD2529Q SONY CDP-XE900 CXD8505 + CXA8055 SONY CHC-P11 (mini hifi) PCM1710U SONY DAS-R1 2x TDA1541A S1 (single crown) SONY PLAYSTATION SCPH-1002 AKM AK4310VM or AK4310AVM (late) SONY PLAYSTATION SCPH-5502 AKM AK4310AVM SONY PLAYSTATION SCPH-5552 AKM AK4310AVM SOUND WAVE CD1100 LC7881 SUDGEN OPTIMA TDA1543 SUDGEN SDA-1 TDA1541 SUDGEN SDT-1 TDA1541A S1 (single crown) T+A CD1210R SM5864AP TAG McLAREN CD20R CS4329 TALK ELECTRONICS THUNDER 3 CS4390 TASCAM CD201 MN6474
TEAC CPD3450SE TEAC PD155mk2 TEAC PD160 TEAC PD365 TEAC VRDS 7 TEAC VRDS 8 TEAC VRDS 9 TEAC VRDS 10SE TEAC VRDS 25 TEAC ZD5000 TECHNICS SL-P1 TECHNICS SL-P2 TECHNICS SL-P50 TECHNICS SL-P110 TECHNICS SL-P120K E TECHNICS SL-P272A TECHNICS SL-P520 TECHNICS SL-P555 TECHNICS SL-P720 TECHNICS SL-P770 TECHNICS SL-P990 TECHNICS SL-P999 TECHNICS SL-P1200 TECHNICS SL-PG480A TECHNICS SL-PJ28A TECHNICS SL-PS670D TECHNICS SL-PS700 TECHNICS SL-PS770A THETA DSP THOMSON LAD300 THULE CD100 THULE SPIRIT TOSHIBA XR40 UHER UCD-210 UNIVERSUM CD4682 USHER CD-100 WADIA 23 WADIA 850 WADIA 860
YDC103 Y3015 TC9218F YM7121B SAA7350 PCM1702 PCM1702 TDA1547 AD1862J PCM53 PCM53 PCM53 MN6474 PCM54HP PCM54HP MN6474 MN6618A MN6471 MN6618A 2x PCM56P + 2x PCM56P-J 4x PCM56P-J 4x PCM56P-J PCM54HP MN662713 MN6477 MN6474 MN6474 MN64733 PCM67 TD6720N CS4303 PCM1715U TD6705AP LC7882 PCM56 PCM1732 AD1865 PCM1702 4x PCM1702
WADIA 861 YAMAHA CD-2 YAMAHA CD-3 YAMAHA CD-2000 YAMAHA CDX-3 YAMAHA CDX-410 YAMAHA CDX-420 YAMAHA CDX-470 YAMAHA CDX-480 YAMAHA CDX-490 YAMAHA CDX-580 YAMAHA CDX-590 YAMAHA CDX-593 YAMAHA CDX-700 YAMAHA CDX-810 YAMAHA CDX-880 YAMAHA CDX-890 YAMAHA CDX-893 YAMAHA CDX-900 YAMAHA CDX-993 YAMAHA CDX-1100 YAMAHA CDX-2020